IB/ocrdma: fix incorrect fall-through on switch statement

In the case where mbox_status is OCRDMA_MBX_STATUS_FAILED and
add_status is OCRDMA_MBX_STATUS_FAILED err_num is assigned -EAGAIN
however the case OCRDMA_MBX_STATUS_FAILED is missing a break and
falls through to the default case which then re-assigns err_num
to -EFAULT.   Fix this so that err_num is assigned to -EAGAIN
for the add_status OCRDMA_MBX_STATUS_FAILED case and -EFAULT
otherwise.

Detected by CoverityScan CID#703125 ("Missing break in switch")

Fixes: fe2caefcdf58 ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/ipoib: Suppress the retry related completion errors

IPoIB doesn't support transport/rnr retry schemes as per
RFC so those errors are expected. No need to flood the
log files with them.

Tested-by: Michael Nowak <michael.nowak@oracle.com>
Tested-by: Rafael Alejandro Peralez <rafael.peralez@oracle.com>
Tested-by: Liwen Huang <liwen.huang@oracle.com>
Tested-by: Hong Liu <hong.x.liu@oracle.com>
Reviewed-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Reported-by: Rajiv Raja <rajiv.raja@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

iw_cxgb4: remove the stid on listen create failure

If a listen create fails, then the server tid (stid) is incorrectly left
in the stid idr table, which can cause a touch-after-free if the stid
is looked up and the already freed endpoint is touched.  So make sure
and remove it in the error path.

Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

iw_cxgb4: drop listen destroy replies if no ep found

If the thread waiting for a CLOSE_LISTSRV_RPL times out and bails,
then we need to handle a subsequent CPL if it arrives and the stid has
been released.  In this case silently drop it.

Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

iw_cxgb4: put ep reference in pass_accept_req()

The listening endpoint should always be dereferenced at the end of
pass_accept_req().

Fixes: f86fac79afec ("RDMA/iw_cxgb4: atomic find and reference for listening endpoints")

Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Fix for core panic

Build with the latest patches resulted in panic:
11384.486289] BUG: unable to handle kernel NULL pointer dereference at
         (null)
[11384.486293] IP:           (null)
[11384.486295] PGD 0
[11384.486295] P4D 0
[11384.486296]
[11384.486299] Oops: 0010 [#1] SMP
......... snip ......
[11384.486401] CPU: 0 PID: 968 Comm: kworker/0:1H Tainted: G        W  O
    4.13.0-a-stream-20170825 #1
[11384.486402] Hardware name: Intel Corporation S2600WT2R/S2600WT2R,
BIOS SE5C610.86B.01.01.0014.121820151719 12/18/2015
[11384.486418] Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
[11384.486419] task: ffff880850579680 task.stack: ffffc90007fec000
[11384.486420] RIP: 0010:          (null)
[11384.486420] RSP: 0018:ffffc90007fef970 EFLAGS: 00010206
[11384.486421] RAX: ffff88084cfe8000 RBX: ffff88084dce4000 RCX:
ffffc90007fef978
[11384.486422] RDX: 0000000000000000 RSI: 0000000000000001 RDI:
ffff88084cfe8000
[11384.486422] RBP: ffffc90007fefab0 R08: 0000000000000000 R09:
ffff88084dce4080
[11384.486423] R10: ffffffffa02d7f60 R11: 0000000000000000 R12:
ffff88105af65a00
[11384.486423] R13: ffff88084dce4000 R14: 000000000000c000 R15:
000000000000c000
[11384.486424] FS:  0000000000000000(0000) GS:ffff88085f400000(0000)
knlGS:0000000000000000
[11384.486425] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[11384.486425] CR2: 0000000000000000 CR3: 0000000001c09000 CR4:
00000000001406f0
[11384.486426] Call Trace:
[11384.486431]  ? is_valid_mcast_lid.isra.21+0xfb/0x110 [ib_core]
[11384.486436]  ib_attach_mcast+0x6f/0xa0 [ib_core]
[11384.486441]  ipoib_mcast_attach+0x81/0x190 [ib_ipoib]
[11384.486443]  ipoib_mcast_join_complete+0x354/0xb40 [ib_ipoib]
[11384.486448]  mcast_work_handler+0x330/0x6c0 [ib_core]
[11384.486452]  join_handler+0x101/0x220 [ib_core]
[11384.486455]  ib_sa_mcmember_rec_callback+0x54/0x80 [ib_core]
[11384.486459]  recv_handler+0x3a/0x60 [ib_core]
[11384.486462]  ib_mad_recv_done+0x423/0x9b0 [ib_core]
[11384.486466]  __ib_process_cq+0x5d/0xb0 [ib_core]
[11384.486469]  ib_cq_poll_work+0x20/0x60 [ib_core]
[11384.486472]  process_one_work+0x149/0x360
[11384.486474]  worker_thread+0x4d/0x3c0
[11384.486487]  kthread+0x109/0x140
[11384.486488]  ? rescuer_thread+0x380/0x380
[11384.486489]  ? kthread_park+0x60/0x60
[11384.486490]  ? kthread_park+0x60/0x60
[11384.486493]  ret_from_fork+0x25/0x30
[11384.486493] Code:  Bad RIP value.
[11384.486493] Code:  Bad RIP value.
[11384.486496] RIP:           (null) RSP: ffffc90007fef970
[11384.486497] CR2: 0000000000000000
[11384.486531] ---[ end trace b1acec6fb4ff6e75 ]---
[11384.532133] Kernel panic - not syncing: Fatal exception
[11384.536541] Kernel Offset: disabled
[11384.969491] ---[ end Kernel panic - not syncing: Fatal exception
[11384.976875] sched: Unexpected reschedule of offline CPU#1!
[11384.983646] ------------[ cut here ]------------

Rdma device driver may not have implemented (*get_link_layer)()
so it can not be called directly. Should use appropriate helper function.

Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Fixes: 523633359224 ("IB/core: Fix the validations of a multicast LID in attach or detach operations")
Cc: stable@kernel.org # 4.13
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Expose ioctl interface through experimental Kconfig

Add CONFIG_INFINIBAND_EXP_USER_ACCESS that enables the ioctl
interface. This interface is experimental and is subject to change.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Assign root to all drivers

In order to use the parsing tree, we need to assign the root
to all drivers. Currently, we just assign the default parsing
tree via ib_uverbs_add_one. The driver could override this by
assigning a parsing tree prior to registering the device.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add completion queue (cq) object actions

Adding CQ ioctl actions:
1. create_cq
2. destroy_cq

This requires adding the following:
1. A specification describing the method
a. Handler
b. Attributes specification
Each attribute is one of the following:
a. PTR_IN - input data
    Note: This could be encoded inlined for
  data < 64bit
b. PTR_OUT - response data
c. IDR - idr based object
d. FD - fd based object
                Blobs attributes (clauses a and b) contain their type,
        while objects specifications (clauses c and d)
                contains the expected object type (for example, the
                given id should be UVERBS_TYPE_PD) and the required
                access (READ, WRITE, NEW or DESTROY). If a NEW is
                required, the new object's id will be assigned to this
                attribute. All attributes could get UA_FLAGS
                attribute. Currently we support stating that an
attribute is mandatory or that the specification size
                corresponds to a lower bound (and that this attribute
could be extended).
We currently add both default attributes and the two
generic UHW_IN and UHW_OUT driver specific attributes.
2. Handler
   A handler gets a uverbs_attr_bundle. The handler developer uses
   uverbs_attr_get to fetch an attribute of a given id.
   Each of these attribute groups correspond to the specification
   group defined in the action (clauses 1.b and 1.c respectively).
   The indices of these arrays corresponds to the attribute ids
   declared in the specifications (clause 2).

   The handler is quite simple. It assumes the infrastructure fetched
   all objects and locked, created or destroyed them as required by
   the specification. Pointer (or blob) attributes were validated to
   match their required sizes. After the handler finished, the
   infrastructure commits or rollbacks the objects.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add legacy driver's user-data

In this phase, we don't want to change all the drivers to use
flexible driver's specific attributes. Therefore, we add two default
attributes: UHW_IN and UHW_OUT. These attributes are optional in some
methods and they encode the driver specific command data. We add
a function that extract this data and creates the legacy udata over
it.

Driver's data should start from UVERBS_UDATA_DRIVER_DATA_FLAG. This
turns on the first bit of the namespace, indicating this attribute
belongs to the driver's namespace.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Export ioctl enum types to user-space

Add a new ib_user_ioctl_verbs.h which exports all required ABI
enums and structs to the user-space.
Export the default types to user-space through this file.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Explicitly destroy an object while keeping uobject

When some objects are destroyed, we need to extract their status at
destruction. After object's destruction, this status
(e.g. events_reported) relies in the uobject. In order to have the
latest and correct status, the underlying object should be destroyed,
but we should keep the uobject alive and read this information off the
uobject. We introduce a rdma_explicit_destroy function. This function
destroys the class type object (for example, the IDR class type which
destroys the underlying object as well) and then convert the uobject
to be of a null class type. This uobject will then be destroyed as any
other uobject once uverbs_finalize_object[s] is called.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add macros for declaring methods and attributes

This patch adds macros for declaring objects, methods and
attributes. These definitions are later used by downstream patches
to declare some of the default types.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add uverbs merge trees functionality

Different drivers support different features and even subset of the
common uverbs implementation. Currently, this is handled as bitmask
in every driver that represents which kind of methods it supports, but
doesn't go down to attributes granularity. Moreover, drivers might
want to add their specific types, methods and attributes to let
their user-space counter-parts be exposed to some more efficient
abstractions. It means that existence of different features is
validated syntactically via the parsing infrastructure rather than
using a complex in-handler logic.

In order to do that, we allow defining features and abstractions
as parsing trees. These per-feature parsing tree could be merged
to an efficient (perfect-hash based) parsing tree, which is later
used by the parsing infrastructure.

To sum it up, this makes a parse tree unique for a device and
represents only the features this particular device supports.
This is done by having a root specification tree per feature.
Before a device registers itself as an IB device, it merges
all these trees into one parsing tree. This parsing tree
is used to parse all user-space commands.

A future user-space application could read this parse tree. This
tree represents which objects, methods and attributes are
supported by this device.

This is based on the idea of
Jason Gunthorpe <jgunthorpe@obsidianresearch.com>

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add DEVICE object and root tree structure

This adds the DEVICE object. This object supports creating the context
that all objects are created from. Moreover, it supports executing
methods which are related to the device itself, such as QUERY_DEVICE.
This is a singleton object (per file instance).

All standard objects are put in the root structure. This root will later
on be used in drivers as the source for their whole parsing tree.
Later on, when new features are added, these drivers could mix this root
with other customized objects.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Declare an object instead of declaring only type attributes

Switch all uverbs_type_attrs_xxxx with DECLARE_UVERBS_OBJECT
macros. This will be later used in order to embed the object
specific methods in the objects as well.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add new ioctl interface

In this ioctl interface, processing the command starts from
properties of the command and fetching the appropriate user objects
before calling the handler.

Parsing and validation is done according to a specifier declared by
the driver's code. In the driver, all supported objects are declared.
These objects are separated to different object namepsaces. Dividing
objects to namespaces is done at initialization by using the higher
bits of the object ids. This initialization can mix objects declared
in different places to one parsing tree using in this ioctl interface.

For each object we list all supported methods. Similarly to objects,
methods are separated to method namespaces too. Namespacing is done
similarly to the objects case. This could be used in order to add
methods to an existing object.

Each method has a specific handler, which could be either a default
handler or a driver specific handler.
Along with the handler, a bunch of attributes are specified as well.
Similarly to objects and method, attributes are namespaced and hashed
by their ids at initialization too. All supported attributes are
subject to automatic fetching and validation. These attributes include
the command, response and the method's related objects' ids.

When these entities (objects, methods and attributes) are used, the
high bits of the entities ids are used in order to calculate the hash
bucket index. Then, these high bits are masked out in order to have a
zero based index. Since we use these high bits for both bucketing and
namespacing, we get a compact representation and O(1) array access.
This is mandatory for efficient dispatching.

Each attribute has a type (PTR_IN, PTR_OUT, IDR and FD) and a length.
Attributes could be validated through some attributes, like:
(*) Minimum size / Exact size
(*) Fops for FD
(*) Object type for IDR

If an IDR/fd attribute is specified, the kernel also states the object
type and the required access (NEW, WRITE, READ or DESTROY).
All uobject/fd management is done automatically by the infrastructure,
meaning - the infrastructure will fail concurrent commands that at
least one of them requires concurrent access (WRITE/DESTROY),
synchronize actions with device removals (dissociate context events)
and take care of reference counting (increase/decrease) for concurrent
actions invocation. The reference counts on the actual kernel objects
shall be handled by the handlers.

 objects
+--------+
|        |
|        |   methods                                                                +--------+
|        |   ns         method      method_spec                           +-----+   |len     |
+--------+  +------+[d]+-------+   +----------------+[d]+------------+    |attr1+-> |type    |
| object +> |method+-> | spec  +-> +  attr_buckets  +-> |default_chain+--> +-----+   |idr_type|
+--------+  +------+   |handler|   |                |   +------------+    |attr2|   |access  |
|        |  |      |   +-------+   +----------------+   |driver chain|    +-----+   +--------+
|        |  |      |                                    +------------+
|        |  +------+
|        |
|        |
|        |
|        |
|        |
|        |
|        |
|        |
|        |
|        |
+--------+

[d] = Hash ids to groups using the high order bits

The right types table is also chosen by using the high bits from
the ids. Currently we have either default or driver specific groups.

Once validation and object fetching (or creation) completed, we call
the handler:
int (*handler)(struct ib_device *ib_dev, struct ib_uverbs_file *ufile,
               struct uverbs_attr_bundle *ctx);

ctx bundles attributes of different namespaces. Each element there
is an array of attributes which corresponds to one namespaces of
attributes. For example, in the usually used case:

 ctx                               core
+----------------------------+     +------------+
| core:                      +---> | valid      |
+----------------------------+     | cmd_attr   |
| driver:                    |     +------------+
|----------------------------+--+  | valid      |
                                |  | cmd_attr   |
                                |  +------------+
                                |  | valid      |
                                |  | obj_attr   |
                                |  +------------+
                                |
                                |  drivers
                                |  +------------+
                                +> | valid      |
                                   | cmd_attr   |
                                   +------------+
                                   | valid      |
                                   | cmd_attr   |
                                   +------------+
                                   | valid      |
                                   | obj_attr   |
                                   +------------+

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/vmw_pvrdma: Fix a signedness

Fixes: 29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/vmw_pvrdma: Report network header type in WC

We should report the network header type in the work completion so that
the kernel can infer the right RoCE type headers.

Reviewed-by: Bryan Tan <bryantan@vmware.com>
Signed-off-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()

For RoCE, ib_init_ah_from_wc() can follow the path

    ib_init_ah_from_wc() ->
      rdma_addr_find_l2_eth_by_grh() ->
        rdma_resolve_ip()

and rdma_resolve_ip() will sleep in kzalloc() and wait_for_completion().

However, developers will not see any warnings if they use ib_init_ah_from_wc()
in an atomic context and test only on IB, because the function doesn't
sleep in that case.

Add a might_sleep() so that lockdep will catch bugs no matter what hardware is
used to test.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/cm: Fix sleeping in atomic when RoCE is used

A couple of places in the CM do

    spin_lock_irq(&cm_id_priv->lock);
    ...
    if (cm_alloc_response_msg(work->port, work->mad_recv_wc, &msg))

However when the underlying transport is RoCE, this leads to a sleeping function
being called with the lock held - the callchain is

    cm_alloc_response_msg() ->
      ib_create_ah_from_wc() ->
        ib_init_ah_from_wc() ->
          rdma_addr_find_l2_eth_by_grh() ->
            rdma_resolve_ip()

and rdma_resolve_ip() starts out by doing

    req = kzalloc(sizeof *req, GFP_KERNEL);

not to mention rdma_addr_find_l2_eth_by_grh() doing

    wait_for_completion(&ctx.comp);

to wait for the task that rdma_resolve_ip() queues up.

Fix this by moving the AH creation out of the lock.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add support to finalize objects in one transaction

The new ioctl based infrastructure either commits or rollbacks
all objects of the method as one transaction. In order to do
that, we introduce a notion of dealing with a collection of
objects that are related to a specific method.

This also requires adding a notion of a method and attribute.
A method contains a hash of attributes, where each bucket
contains several attributes. The attributes are hashed according
to their namespace which resides in the four upper bits of the id.

For example, an object could be a CQ, which has an action of CREATE_CQ.
This action has multiple attributes. For example, the CQ's new handle
and the comp_channel. Each layer in this hierarchy - objects, methods
and attributes is split into namespaces. The basic example for that is
one namespace representing the default entities and another one
representing the driver specific entities.

When declaring these methods and attributes, we actually declare
their specifications. When a method is executed, we actually
allocates some space to hold auxiliary information. This auxiliary
information contains meta-data about the required objects, such
as pointers to their type information, pointers to the uobjects
themselves (if exist), etc.
The specification, along with the auxiliary information we allocated
and filled is given to the finalize_objects function.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add a generic way to execute an operation on a uobject

The ioctl infrastructure treats all user-objects in the same manner.
It gets objects ids from the user-space and by using the object type
and type attributes mentioned in the object specification, it executes
this required method. Passing an object id from the user-space as
an attribute is carried out in three stages. The first is carried out
before the actual handler and the last is carried out afterwards.

The different supported operations are read, write, destroy and create.
In the first stage, the former three actions just fetches the object
from the repository (by using its id) and locks it. The last action
allocates a new uobject. Afterwards, the second stage is carried out
when the handler itself carries out the required modification of the
object. The last stage is carried out after the handler finishes and
commits the result. The former two operations just unlock the object.
Destroy calls the "free object" operation, taking into account the
object's type and releases the uobject as well. Creation just adds the
new uobject to the repository, making the object visible to the
application.

In order to abstract these details from the ioctl infrastructure
layer, we add uverbs_get_uobject_from_context and
uverbs_finalize_object functions which corresponds to the first
and last stages respectively.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Documentation: Hardware tag matching

Add document providing definitions of terms and core explanations
for tag matching (TM) protocols, eager and rendezvous,
TM application header, tag list manipulations and matching process.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Support IB_SRQT_TM

Pass to mlx5_core flag to enable rendezvous offload, list_size and CQ
when SRQ created with IB_SRQT_TM.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

net/mlx5: Add XRQ support

Add support to new XRQ(eXtended shared Receive Queue)
hardware object. It supports SRQ semantics with addition
of extended receive buffers topologies and offloads.

Currently supports tag matching topology and rendezvouz offload.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Fill XRQ capabilities

Provide driver specific values for XRQ capabilities.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/uverbs: Expose XRQ capabilities

Make XRQ capabilities available via ibv_query_device() verb.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/uverbs: Add new SRQ type IB_SRQT_TM

Add new SRQ type capable of new tag matching feature.

When SRQ receives a message it will search through the matching list
for the corresponding posted receive buffer. The process of searching
the matching list is called tag matching.

In case the tag matching results in a match, the received message will
be placed in the address specified by the receive buffer. In case no
match was found the message will be placed in a generic buffer until the
corresponding receive buffer will be posted. These messages are called
unexpected and their set is called an unexpected list.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/uverbs: Add XRQ creation parameter to UAPI

Add tm_list_size parameter to struct ib_uverbs_create_xsrq.
If SRQ type is tag-matching this field defines maximum size
of tag matching list. Otherwise, it is expected to be zero.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add new SRQ type IB_SRQT_TM

This patch adds new SRQ type - IB_SRQT_TM. The new SRQ type supports tag
matching and rendezvous offloads for MPI applications.

When SRQ receives a message it will search through the matching list
for the corresponding posted receive buffer. The process of searching
the matching list is called tag matching.
In case the tag matching results in a match, the received message will
be placed in the address specified by the receive buffer. In case no
match was found the message will be placed in a generic buffer until the
corresponding receive buffer will be posted. These messages are called
unexpected and their set is called an unexpected list.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Separate CQ handle in SRQ context

Before this change CQ attached to SRQ was part of XRC specific extension.
Moving CQ handle out makes it available to other types extending SRQ
functionality.

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add XRQ capabilities

This patch adds following TM XRQ capabilities:

* max_rndv_hdr_size - Max size of rendezvous request message
* max_num_tags - Max number of entries in tag matching list
* max_ops - Max number of outstanding list operations
* max_sge - Max number of SGE in tag matching entry
* flags - the following flags are currently defined:
    - IB_TM_CAP_RC - Support tag matching on RC transport

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

net/mlx5: Update HW layout definitions

* add offload_type field to mlx5_ifc_qpc_bits
* update mlx5_ifc_xrqc_bits layout

Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Handle NETDEV_CHANGE events

Without this fix, ports configured on top of ixgbe miss link up
notifications. ibv_query_port() will continue to return IBV_PORT_DOWN even
though the port is up and working.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Avoid ICRC errors by copying into the skb first

The current process is to first calculate the CRC and then copy the client
data into the packet. This leaves a window in which the packet contents and
CRC can get out of sync, if the client changes the data after the CRC is
calculated but before the data is copied.

By copying the data into the packet and then calculating the CRC directly
from the packet contents we eliminate the window.

This can be seen with qperf's ud_bi_bw test. This seems like very
strange/reckless client behavior, but whether the client has mangled its
data or not RXE should be able to transfer it reliably.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Another fix for broken receive queue draining

This fixes another path in rxe_requester() that might overlook stale SKBs,
preventing cleanup.

Fixes: 1217197142d1 ("rxe: fix broken receive queue draining")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Remove unneeded initialization in prepare6()

Fixes: 4ed6ad1eb30e ("IB/rxe: Cache dst in QP instead of getting it...")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Fix up rxe_qp_cleanup()

Replace sk_dst_get()/dst_release() in rxe_qp_cleanup() with sk_dst_reset().
sk_dst_get() takes a new reference on dst, so the dst_release() doesn't
actually release the original reference, which was the design intent.

Fixes: 4ed6ad1eb30e ("IB/rxe: Cache dst in QP instead of getting it...")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Add dst_clone() in prepare_ipv6_hdr()

Otherwise the reference count goes negative as IPv6 packets complete.

Fixes: 4ed6ad1eb30e ("IB/rxe: Cache dst in QP instead of getting it...")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Fix destination cache for IPv6

To successfully match an IPv6 path, the path cookie must match. Store it
in the QP so that the IPv6 path can be reused.

Replace open-coded version of dst_check() with the actual call, fixing the
logic. The open-coded version skips the check call if dst->obsolete is 0
(DST_OBSOLETE_NONE), proceeding to replace the route. DST_OBSOLETE_NONE
means that the route may continue to be used, though.

Fixes: 4ed6ad1eb30e ("IB/rxe: Cache dst in QP instead of getting it...")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Fix up the responder's find_resources() function

The resource array is sized by max_dest_rd_atomic, not max_rd_atomic.
Iterating over max_rd_atomic entries of qp->resp.resources[] will cause
incorrect behavior when the two attributes are different (or even
crash if max_rd_atomic is larger).

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Remove dangling prototype

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Disable completion upcalls when a CQ is destroyed

This prevents the stack from accessing userspace objects while they
are being torn down.

One possible sequence of events:
 - Userspace program exits
 - ib_uverbs_cleanup_ucontext() runs, calling ib_destroy_qp(),
   ib_destroy_cq(), etc. and releasing/freeing the UCQ
   - The QP still has tasklets running, so it isn't destroyed yet
   - The CQ is referenced by the QP, so the CQ isn't destroyed yet
   - The UCQ is kfree()'d anyway
 - A send work request completes
 - rxe_send_complete() calls cq->ibcq.comp_handler()
 - ib_uverbs_comp_handler() runs and crashes; the event queue is checked
   for is_closed, but it has no way to check the ib_ucq_object before
   accessing it

The reference counting on the CQ doesn't protect against this since the CQ
hasn't been destroyed yet.
There's no available interface to deregister the UCQ from the CQ, and it
didn't appear that attempting to add reference counting to the UCQ was
going to be a good way to go since this solution is much simpler.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Move refcounting earlier in rxe_send()

The network stack will call nskb's destructor, rxe_skb_tx_dtor(), if the
packet gets dropped by ip_local_out()/ip6_local_out(). Thus we need to add
the QP ref before output to avoid extra dereferences during network
congestion. This could lead to unwanted destruction of the QP.

Fix up the skb_out accounting, too.

Fixes: fda85ce91240 ("IB/rxe: Fix kernel panic from skb destructor")
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rdmavt: Handle dereg of inuse MRs properly

A destroy of an MR prior to destroying the QP can cause the following
diagnostic if the QP is referencing the MR being de-registered:

hfi1 0000:05:00.0: hfi1_0: rvt_dereg_mr timeout mr ffff8808562108
              00 pd ffff880859b20b00

The solution is to when the a non-zero refcount is encountered when
the MR is destroyed the QPs needs to be iterated looking for QPs in
the same PD as the MR.  If rvt_qp_mr_clean() detects any such QP
references the rkey/lkey, the QP needs to be put into an error state
via a call to rvt_qp_error() which will trigger the clean up of any
stuck references.

This solution is as specified in IBTA 1.3 Volume 1 11.2.10.5.

[This is reproduced with the 0.4.9 version of qperf and the rc_bw test]

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/qib: Convert qp_stats debugfs interface to use new iterator API

Continue porting copy/paste code into rdmavt from qib.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Convert qp_stats debugfs interface to use new iterator API

Continue moving copy/paste code into rdmavt.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Convert hfi1_error_port_qps() to use new QP iterator

Change hfi1_error_port_qps() to use the new rvt_qp_iter() in its QP
scanning.

Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rdmavt: Add QP iterator API for QPs

There are currently 3 spots in the qib and hfi1 driver that have
knowledge of the internal QP hash list that should only be in
scope to rdmavt QP code.

Add an iterator API for processing all QPs to hide the
nature of the RCU hashlist.

The API consists of:
- rvt_qp_iter_init()
  * For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter_next()
  * For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter()
  * For iterating all QPs

The first two are used for things like seq_file prints.

The last is for code that just needs to iterate all QPs
in the system.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Use accessor to determine ring size

The qp_stats print will soon be moving to rdmavt, so use the proper
accessor to get the ring size rather than a driver supplied constant.

Fixes: Commit ff8d836efe06 ("IB/hfi1: Add receiving queue info to qp_stats")
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/qib: Stricter bounds checking for copy to buffer

Replace 'strcpy' with 'strncpy' to restrict the number
of bytes copied to the buffer.

Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hif1: Remove static tracing from SDMA hot path

The hfi1_cdbg() macro can be instantiated in the hot path even when it
is not in use.  This shows up on perf profiles.

Rework the macros (for SDMA and MMU), to use the trace interface directly
to eliminate this performance hit.

Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Acquire QSFP cable information on loopback

Currently, QSFP information is not queried
in cases where loopback was set up and QSFP module is
present.

Acquire QSFP information in case of loopback.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

i40iw: make some structures const

Make some structures const as they are only used during a copy
operation.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: constify vm_operations_struct

vm_operations_struct are not supposed to change at runtime.
vm_area_struct structure working with const vm_operations_struct.
So mark the non-const vm_operations_struct structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/bnxt_re: remove unnecessary call to memset

call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.

Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/usnic: check for allocation failure

usnic_uiom_get_dev_list() can return ERR_PTR(-ENOMEM) so we should check
for that.

Fixes: e3cf00d0a87f ("IB/usnic: Add Cisco VIC low-level hardware driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Add opcode states to qp_stats

These fields allow for debugging send engine processing.

Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Add received request info to qp_stats

The rvt_ack_entry pointed to by s_tail_ack_queue provides important
info about the request that has just been processed or is being processed
on the responder side of a RC connection. This patch adds this info to
the qp_stats to assist debugging.

Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Fix whitespace alignment issue for MAD

Fix a tab alignment issue present in pr_err_ratelimited
error message.

Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Move structure and MACRO definitions in user_sdma.c to user_sdma.h

Clean up user_sdma.c by moving the structure and MACRO definitions into
the header file user_sdma.h

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Move structure definitions from user_exp_rcv.c to user_exp_rcv.h

Clean up user_exp_rcv.c file by moving structure definitions into header
file user_exp_rcv.h. Since these structure definitions depend on the
structure definitions in mmu_rb.h, move #include "mmu_rb.h" above
the include "user_exp_rcv.h" or include of header files that include
user_exp_rcv.h

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Remove duplicate definitions of num_user_pages() function

num_user_pages() function has been defined in both user_exp_rcv.c file
and user_sdma.c file. Move the function definition to a header file so
there is only one definition in the source repo.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Fix the bail out code in pin_vector_pages() function

In pin_vector_pages() function, if there is any error while pinning the
pages or while adding a pinned buffer to the cache, the bail out code
needs to unpin any pinned pages that are not in the cache and adjust the
n_locked counter that counts the total pages pinned. The current bail
out code doesn't seem to be doing it right in two cases:

1. Before pinning required pages for a buffer, the SDMA pinned buffer
cache is searched to see if the virtual address range that needs to be
pinned is already pinned. If there isn't a hit in the cache, a new node
is created for the buffer and is added to the cache after the buffer is
pinned. If adding the new node to the cache fails, the n_locked count is
decremented properly but the pinned pages are not freed. This commit
fixes this issue.

2. If there is a hit in the SDMA cache, but the cached buffer doesn't
have enough pages to cover the entire address range that needs to be
pinned, the node for the cached buffer is extracted from the cache,
remaining pages needed are pinned and added to the node. The node is
finally added back into the cache. If there is an error pinning the
extra pages, the bail out code frees all the pages in the node but the
n_locked count is not being decremented by the no of pages in the node
that are freed. This commit fixes this issue.

This commit fixes the above two issues by creating a new function that
frees the pages in a node and decrements the n_locked count by the
number of pages freed.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Clean up pin_vector_pages() function

Clean up pin_vector_pages() function by moving page pinning related code
to a separate function since it really stands on its own.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Clean up user_sdma_send_pkts() function

user_sdma_send_pkts() function is unnecessarily long. Clean it up by
moving some of its code into separate functions.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Clean up hfi1_user_exp_rcv_setup function

Clean up hfi1_user_exp_rcv_setup function by moving page pinning and
unpinning related code to separate functions. In order to reduce the
number of parameters passed between functions, a new data structure
struct tid_user_buf is defined and used.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Improve local kmem_cache_alloc performance

Performance analysis shows that the cache callback function
sdma_kmem_cache_ctor contributes to 1/2 of the kmem_cache_allocs
time.

Since all of the fields in the allocated data structure are initialized
in the code path, remove the _ctor function.

Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/hfi1: Ratelimit prints from sdma_interrupt

Ratelimit error prints from sdma_interrupt function
that could swarm dmesg otherwise.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Grzegorz Morys <grzegorz.morys@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/qib: Stricter bounds checking for copy and array access

Added checking on index value of array 'guids' in qib_ruc.c.
Pass in corrrect size of array for memset operation in qib_mad.c.

Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/qib: Remove unnecessary memory allocation for boardname

Remove all the memory allocation implemented for boardname and
directly assign the defined string literal.

Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/{qib, hfi1}: Avoid flow control testing for RDMA write operation

Section 9.7.7.2.5 of the 1.3 IBTA spec clearly says that receive
credits should never apply to RDMA write.

qib and hfi1 were doing that.  The following situation will result
in a QP hang:
- A prior SEND or RDMA_WRITE with immmediate consumed the last
  credit for a QP using RC receive buffer credits
- The prior op is acked so there are no more acks
- The peer ULP fails to post receive for some reason
- An RDMA write sees that the credits are exhausted and waits
- The peer ULP posts receive buffers
- The ULP posts a send or RDMA write that will be hung

The fix is to avoid the credit test for the RDMA write operation.

Cc: <stable@vger.kernel.org>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rdmavt: Use rvt_put_swqe() in rvt_clear_mr_ref()

hfi1 and qib were converted in previous patches, do the same for rdmavt.

Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Merge branch 'mellanox' into k.o/for-next

Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Report mlx5 enhanced multi packet WQE capability

Expose enhanced multi packet WQE capability to user space through
query_device by uhw.

Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Allow posting multi packet send WQEs if hardware supports

Set the field to allow posting multi packet send WQEs if hardware
supports this feature. This doesn't mean the send WQEs will be for
multi packet unless the send WQE was prepared according to multi
packet send WQE format.

User space shall use flag MLX5_IB_ALLOW_MPW to check if hardware
supports MPW and allows MPW in SQ context.

Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Add support for multi underlay QP

Set underlay QPN as part of flow rule when it's applicable.

There is one root flow table in the NIC RX namespace and all the
underlay QPs steer the traffic to this flow table.
In order to prevent QP to get traffic which is not target to its
underlay QP, we need to set the underlay QP number as part of
the steering matching.

Note:
When multicast traffic is sent the QPN filtering is done by the firmware
as some early step. Adding the QPN match on the flow table entry is
wrong as by that time the target QPN holds the multicast address (e.g.
FF(s)) and it won't match.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Fix integer overflow when page_shift == 31

Fix a bug where MR registration fails when mlx5_ib_cont_pages
indicates that the MR can be mapped using 2GB pages (page_shift == 31).

Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Fix memory leak in clean_mr error path

In clean_mr error path the 'mr' should be freed.

Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Decouple MR allocation and population flows

mlx5 compatible devices have two ways of populating the MTT
table of an MKEY: using a FW command and using a UMR WQE.

A UMR is much faster, so it should be used whenever possible.
Unfortunately the code today uses UMR only if the MKEY was allocated
from the MR cache.

Fix the code to use UMR even for MKEYs that were allocated using
a FW command.

Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Enable UMR for MRs created with reg_create

This patch is the first step in decoupling UMR usage and
allocation from the MR cache. The only functional change
in this patch is to enables UMR for MRs created with
reg_create.

This change fixes a bug where ODP memory regions that
were not allocated from the MR cache did not have UMR
enabled.

Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Expose software parsing for Raw Ethernet QP

Software parsing (SWP) is a feature that can be used to instruct the
device to stop using its internal parser and to parse packets on the
transmit path according to offsets set for each packets.

Through this feature, the device allows the handling of checksum and
LSO by the hardware according to the location of IP and TCP/UDP
headers.

Enable SW parsing on Raw Ethernet send queue by default if firmware
supports it and report these capabilities to user space.

Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/i40iw: Remove unused argument

None of the calls to i40iw_netdev_vlan_ipv6 are using mac so let's
remove it from func's args-list.

Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/qedr: fix spelling mistake: "invlaid" -> "invalid"

Trivial fix to spelling mistake in DP_ERR error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB: Avoid ib_modify_port() failure for RoCE devices

IB CM calls ib_modify_port() irrespective of link layer. If the
failure is returned, the mad agent gets unregistered for those
devices. Recently, modify_port() hook was removed from some of the
low level drivers as it was always returning success. This breaks
rdma connection establishment over those devices.
For ethernet devices, Qkey violation and port capabilities are not
applicable. So returning success for RoCE when modify_port hook is
is not implemented.

Cc: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/vmw_pvrdma: Update device query parameters and port caps

Added support for two device caps - max_sge_rd, max_fast_reg_page_list_len
and the IP_BASED_GIDS port cap flag.

Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Bryan Tan <bryantan@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/vmw_pvrdma: Add RoCEv2 support

The driver version is bumped for compatibility purposes. Also, send correct
GID type during register to device. Added compatibility check macros for
the device.

Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Bryan Tan <bryantan@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/ipoib: Enable ioctl for to IPoIB rdma netdevs

Adds support for ioctl callback in the RDMA netdevs to allow
supporting functions not handled by the generic interface code.

Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Eitan Rabin <rabin@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/nes: Remove zeroed parameter from port query callback

There is no need to explicitly zero parameters, because
the structure requested to be filled already initialized to zeros.

Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/mlx4: Properly annotate link layer variable

The rdma_port_get_link_layer() returns enum rdma_link_layer as
a return value, hence it is better to store the return value in
specially annotated variable and not in int.

Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA/mlx5: Limit scope of get vector affinity local function

The mlx5_ib_get_vector_affinity() call is local to main.c file and there
is no need to be declared globally visible.

Fixes: 40b24403f33e ("mlx5: support ->get_vector_affinity")
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Make rxe_counter_name static

rxe_counter_name is used in rxe_hw_counters.c only. Make it static.

Fixes: 0b1e5b99a48b ('IB/rxe: Add port protocol stats')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/ipoib: Sync between remove_one to sysfs calls that use rtnl_lock

In order to avoid deadlock between sysfs functions (like create/delete
child) and remove_one (both of them are using the sysfs lock and
rtnl_lock) the driver will use a state mutex for sync.

That will fix traces as the following:
schedule+0x3e/0x90
kernfs_drain+0x75/0xf0
? wait_woken+0x90/0x90
__kernfs_remove+0x12e/0x1c0
kernfs_remove+0x25/0x40
sysfs_remove_dir+0x57/0x90
kobject_del+0x22/0x60
device_del+0x195/0x230
 pm_runtime_set_memalloc_noio+0xac/0xf0
netdev_unregister_kobject+0x71/0x80
rollback_registered_many+0x205/0x2f0
rollback_registered+0x31/0x40
unregister_netdevice_queue+0x58/0xb0
unregister_netdev+0x20/0x30
ipoib_remove_one+0xb7/0x240 [ib_ipoib]
ib_unregister_device+0xbc/0x1b0 [ib_core]
ib_unregister_mad_agent+0x29/0x30 [ib_core]
mlx4_ib_remove+0x67/0x280 [mlx4_ib]
INFO: task echo:24082 blocked for more than 120 seconds.
Tainted: G           OE   4.1.12-37.5.1.el6uek.x86_64 #2
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
Call Trace:
schedule+0x3e/0x90
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x95/0x110
? _rcu_barrier+0x177/0x220
mutex_lock+0x23/0x40
rtnl_lock+0x15/0x20
netdev_run_todo+0x81/0x1f0
rtnl_unlock+0xe/0x10
ipoib_vlan_delete+0x12f/0x1c0 [ib_ipoib]
delete_child+0x69/0x80 [ib_ipoib]
dev_attr_store+0x20/0x30
sysfs_kf_write+0x41/0x50

Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx4: Check that reserved fields in mlx4_ib_create_qp_rss are zero

According to mlx4 convention, need to fail the command due to a non-zero
value in the user data which is expected to be zero.

Fixes: 3078f5f1bd8b ("IB/mlx4: Add support for RSS QP")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx4: Remove redundant attribute in mlx4_ib_create_qp_rss struct

rx_key_len is not in use and needs to be removed.

Fixes: 3078f5f1bd8b ("IB/mlx4: Add support for RSS QP")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx4: Fix struct mlx4_ib_create_wq alignment

The mlx4 ABI defines to have structures with alignment of 64B.

Fixes: 400b1ebcfe31 ("IB/mlx4: Add support for WQ related verbs")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx4: Fix RSS QP type in creation verb

The mlx4 was designed to support QP type of MLX4_IB_QPT_RAW_PACKET.

Fixes: 3078f5f1bd8b ("IB/mlx4: Add support for RSS QP")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Add necessary delay drop assignment

Assign the statistics and configuration structure pointer on success.

Fixes: fe248c3a5837 ('IB/mlx5: Add delay drop configuration and statistics')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mlx5: Fix some spelling mistakes

Fix spelling mistakes in remarks
    "retrun"->"return"
    "Decalring"->"Declaring"

Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>