Felipe Balbi [Tue, 18 Nov 2014 18:07:02 +0000 (12:07 -0600)]
ARM: omap2plus_defconfig: enable XHCI
AM437x devices have a DWC3 IP inside of them.
The host side implementation of DWC3 is XHCI
compliant. By enabling XHCI driver, we get
the USB host port on AM437x Starter Kit working
out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Felipe Balbi [Tue, 18 Nov 2014 18:07:01 +0000 (12:07 -0600)]
ARM: omap2plus_defconfig: enable AM33XX SoC sound
Without this, sound on AM437x Starter Kit will
not work.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Felipe Balbi [Tue, 18 Nov 2014 18:07:00 +0000 (12:07 -0600)]
ARM: omap2plus_defconfig: enable EDT FT5X06 touchscreen
AM437x Starter Kit ships with EDT FT5306 touchscreen
device. By enabling the driver we make sure touchscreen
will work out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Felipe Balbi [Tue, 18 Nov 2014 18:06:59 +0000 (12:06 -0600)]
ARM: omap2plus_defconfig: remove unwanted ethernet drivers
None of these drivers are known to be used on
any platform supported by omap2plus_defconfig,
by removing them we get a slight smaller kernel.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tyler Baker [Thu, 4 Dec 2014 21:24:24 +0000 (13:24 -0800)]
ARM: multi_v7_defconfig: enable MAX77686 PMIC drivers for exynos4412-prime based SoCs
This patch enables the MAX77686 PMIC drivers in the multi_v7_defconfig used
on exynos4412-prime family of SoCs [1]. The exynos4412-prime based boards
are producing the following runtime errors only on the multi_v7_defconfig [2]:
kern.err: deviceless supply vdd_arm not found, using dummy regulator
kern.err: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage to
1287500
kern.err: cpufreq: __target_index: Failed to change cpu frequency: -22
I reviewed the exynos_defconfig, which does not produce these runtime
errors. It was obvious that the exynos_defconfig has the PMIC drivers
enabled, whereas the multi_v7_defconfig does not. This patch has been tested
on a odroid-u2 and a odroid-u3 board. It has resolved the runtime errors.
Therefore, I purpose we enabled these drivers in the multi_v7_defconfig.
[1] http://www.hardkernel.com/main/products/prdt_info.php?g_code=G135270682824
[2] http://storage.armcloud.us/kernel-ci/mainline/
v3.18-rc7-48-g7cc78f8/arm-multi_v7_defconfig/lab-tbaker-00/boot-exynos4412-odroidu3.html
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Thu, 4 Dec 2014 18:09:18 +0000 (19:09 +0100)]
Merge tag 'at91-defconfig' of git://git./linux/kernel/git/nferre/linux-at91 into next/defconfig
Pull "First batch of defconfigs for AT91 / 3.19:" from Nicolas Ferre:
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nicolas Ferre [Mon, 1 Dec 2014 13:06:32 +0000 (14:06 +0100)]
ARM: at91/defconfig: add DM9000 to at91_dt
This chip is present on at91sam9261ek board: add it to the at91_dt_defconfig.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Mon, 1 Dec 2014 12:49:15 +0000 (13:49 +0100)]
ARM: at91/defconfig: add QT1070 to at91_dt
As this touch button driver is used on at91sam9x5ek, it's better to enable it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Mon, 1 Dec 2014 11:27:16 +0000 (12:27 +0100)]
ARM: at91/defconfig: add TCB PWM driver selection
This is the selection of the new PWM driver using TC Blocks. This driver is
useful so we enable it in both sama5 and at91_dt defconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Mon, 1 Dec 2014 11:24:08 +0000 (12:24 +0100)]
ARM: at91/defconfig: add the XDMA driver
Add the Atmel eXtended DMA Controller driver option. This driver is first used
on SAMA5D4 SoCs and only relevant in sama5_defconfig file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ludovic Desroches [Wed, 22 Oct 2014 12:59:18 +0000 (14:59 +0200)]
ARM: at91: sama5: update defconfig
Add neon support for sama5d4 and large blocks/files support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Dmitry Lavnikevich [Fri, 21 Nov 2014 23:55:03 +0000 (07:55 +0800)]
ARM: defconfig: imx_v6_v7_defconfig updates
This is a squash of several imx_v6_v7_defconfig update patches.
- Enable tlv320aic3x audio codec by default (Phytec PBAB01 board)
- Enable DS1307 rtc and gpio fan by default (TBS2910 board)
- Select thermal related drivers
- Add SNVS power off driver
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 28 Nov 2014 21:44:56 +0000 (22:44 +0100)]
Merge tag 'tegra-for-3.19-defconfig' of git://git./linux/kernel/git/tegra/linux into next/defconfig
Pull "ARM: tegra: Default configuration changes for v3.19" from Thierry Reding:
This is merely a regeneration of the default configuration to get rid of
two symbols that are now enabled by default or removed.
* tag 'tegra-for-3.19-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Regenerate default configuration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 28 Nov 2014 21:27:11 +0000 (22:27 +0100)]
Merge tag 'mvebu-defconfig-3.19-2' of git://git.infradead.org/linux-mvebu into next/defconfig
Pull "mvebu defconfig changes for v3.19 (round 2)" from Jason Cooper:
- mvebu
- Add SDHCI, i2c, and MTD_BLOCK
* tag 'mvebu-defconfig-3.19-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add MTD_BLOCK to mvebu_v7_defconfig
ARM: mvebu: enable i2c device in mvebu_v7_defconfig
ARM: mvebu: re-enable SDHCI driver for Armada 38x SoC in v7 defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Zhangfei Gao [Tue, 25 Nov 2014 07:37:26 +0000 (15:37 +0800)]
ARM: multi_v7_defconfig: add driver support for hix5hd2
Tested on hix5hd2 platform with mmc, usb, network, reboot etc.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Krzysztof Kozlowski [Wed, 19 Nov 2014 07:56:19 +0000 (16:56 +0900)]
ARM: exynos_defconfig: Use 16 minors per MMC block device
16 minors per MMC block device are required to boot Rinato (Gear 2)
board because up to 15 partitions are used.
With default 8 minors booting failed with:
[ 1.329092] mmcblk0: mmc0:0001 F5X5MA 3.64 GiB
[ 1.329448] mmcblk0boot0: mmc0:0001 F5X5MA partition 1 4.00 MiB
[ 1.329627] mmcblk0boot1: mmc0:0001 F5X5MA partition 2 4.00 MiB
[ 1.329808] mmcblk0rpmb: mmc0:0001 F5X5MA partition 3 512 KiB
[ 1.335717] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 1.436553] Waiting for root device /dev/mmcblk0p15...
while the correct list of partitions on mmcblk0 for Gear 2 is:
[ 1.436651] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Petazzoni [Thu, 13 Nov 2014 10:11:29 +0000 (11:11 +0100)]
ARM: mvebu: add MTD_BLOCK to mvebu_v7_defconfig
Since many (most?) mvebu platforms have NAND or SPI flashes, it makes
sense to have CONFIG_MTD_BLOCK=y in mvebu_v7_defconfig. The vast
majority of the other ARM defconfigs have it enabled, including
mvebu_v5_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415873489-22446-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Marcin Wojtas [Fri, 14 Nov 2014 15:57:32 +0000 (16:57 +0100)]
ARM: mvebu: enable i2c device in mvebu_v7_defconfig
This commit enables user-space access to I2C bus using char device.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-6-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Marcin Wojtas [Fri, 14 Nov 2014 15:57:28 +0000 (16:57 +0100)]
ARM: mvebu: re-enable SDHCI driver for Armada 38x SoC in v7 defconfig
In the recent update of mvebu_v7_defconfig a config that enables sdhci-pxav3
driver, that supports SDHCI interface of Armada 38x SoC, disappeared.
This commit enables CONFIG_MMC_SDHCI_PXAV3 back.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Fixes
fc9fa8714a75 ("ARM: mvebu: update v7 defconfig with useful options")
Link: https://lkml.kernel.org/r/1415980652-7429-2-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thierry Reding [Fri, 7 Nov 2014 11:36:15 +0000 (12:36 +0100)]
ARM: tegra: Regenerate default configuration
This patch was generated by running 'make tegra_defconfig' followed by
'make savedefconfig' with the v3.18-rc1 tag checked out. Two values go
away: CONFIG_SCSI is selected by CONFIG_ATA and CONFIG_SCSI_MULTI_LUN
was removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Arnd Bergmann [Thu, 20 Nov 2014 16:45:43 +0000 (17:45 +0100)]
Merge tag 'sti-defconfig-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti into next/defconfig
Pull "STi defconfig updates for v3.19" from Maxime Coquelin:
Highlights:
-----------
- Enable ST EHCI and OHCI USB drivers
- Enable STiH416 and STiH415 USB2 PHY driver
* tag 'sti-defconfig-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: multi_v7_defconfig: Enable stih415/6 usb2 phy driver.
ARM: multi_v7_defconfig: Enable st ohci and ehci HCD drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Soren Brinkmann [Mon, 17 Nov 2014 19:55:07 +0000 (11:55 -0800)]
ARM: multi_v7_defconfig: Enable cgroups
This allows booting the kernel with systemd-based root file systems.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 20 Nov 2014 12:13:39 +0000 (13:13 +0100)]
Merge tag 'keystone-soc' of git://git./linux/kernel/git/ssantosh/linux-keystone into next/defconfig
Pull "Keystone config updates for 3.19" from Santosh Shilimkar:
- Enable PCIE controller and related options
- Enable MDIO and ethernet phy options
- Enable DSP IRQCHIP option
* tag 'keystone-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: defconfig: add options to enable PCI controller
ARM: keystone: add pcie related options
ARM: keystone_defconfig: enable mdio and marvell eth phys
ARM: keystone_defconfig: enable dsp irq and gpio support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ray Jui [Wed, 12 Nov 2014 21:03:17 +0000 (13:03 -0800)]
ARM: multi_v7_defconfig: Enable Broadcom Cygnus
Enable Broadcom Cygnus platform support in multi_v7_defconfig
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Scott Branden [Wed, 12 Nov 2014 21:03:16 +0000 (13:03 -0800)]
ARM: multi_v7_defconfig: remove one level of menu from Kconfig
remove menu "Broadcom Mobile SoC Selection"
This requires:
- selecting ARCH_BCM_MOBILE based on SoC selections
- fixup multi_v7_defconfig to work with new menu levels of mach-bcm.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 19 Nov 2014 22:17:42 +0000 (23:17 +0100)]
Merge tag 'mvebu-defconfig-3.19' of git://git.infradead.org/linux-mvebu into next/defconfig
Pull "mvebu defconfig changes for v3.19" from Jason Cooper"
- Add options for DLink DIR665
- Add Armada 370 simple-card audio option
- Add mv88E6171 switch driver option
* tag 'mvebu-defconfig-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: defconfig: Enable the mv88E6171 switch driver
ARM: mvebu: update mvebu_v7_defconfig for Armada 370 audio
ARM: config: Add DLINK DIR665 options to multi_v5_defconfig
ARM: mvebu: Add DLINK DIR665 options to mvebu_v5_defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 19 Nov 2014 22:14:46 +0000 (23:14 +0100)]
Merge tag 'hix5hd2-config-for-3.19' of git://github.com/hisilicon/linux-hisi into next/defconfig
Pull "ARM: HiX5HD2: config update for 3.19" from Wei Xu:
- Enable GMAC, GPIO, Reset, USB, MMC and SATA on HiX5HD2
* tag 'hix5hd2-config-for-3.19' of git://github.com/hisilicon/linux-hisi:
ARM: hisi_defconfig: add driver support for hix5hd2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 19 Nov 2014 21:22:25 +0000 (22:22 +0100)]
Merge tag 'renesas-defconfig-for-v3.19' of git://git./linux/kernel/git/horms/renesas into next/defconfig
Pull "Renesas ARM Based SoC Defconfig Updates for v3.19" from Simon Horman:
* Enable AK4642, Audo DMAC peri peri and R-Car DMAC in shmobile defconrig
* Enable PM Runtime in ape6evm defconfig
* tag 'renesas-defconfig-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: multiplatform: add AK4642 support on defconfig
ARM: shmobile: multiplatform: add Audo DMAC peri peri support on defconfig
ARM: shmobile: multiplatform: add R-Car DMAC support on defconfig
ARM: shmobile: ape6evm: Enable PM Runtime in defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Peter Griffin [Mon, 17 Nov 2014 16:47:00 +0000 (17:47 +0100)]
ARM: multi_v7_defconfig: Enable stih415/6 usb2 phy driver.
This driver is used by the ehci / ohci usb controllers on stih415/6 SoCs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Mon, 17 Nov 2014 16:47:00 +0000 (17:47 +0100)]
ARM: multi_v7_defconfig: Enable st ohci and ehci HCD drivers.
Enable the ehci and ohci drivers in the multi_v7_defconfig so that
the USB controllers on stih41x work by default.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Zhangfei Gao [Wed, 29 Oct 2014 06:05:47 +0000 (14:05 +0800)]
ARM: hisi_defconfig: add driver support for hix5hd2
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Andrew Lunn [Wed, 5 Nov 2014 19:02:01 +0000 (20:02 +0100)]
ARM: mvebu: defconfig: Enable the mv88E6171 switch driver
This switch is used by the 370-rd. Enable it and support for
fixed-link phy configuration.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415214121-29286-4-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 28 Oct 2014 16:08:44 +0000 (17:08 +0100)]
ARM: mvebu: update mvebu_v7_defconfig for Armada 370 audio
Now that the Armada 370 DB audio complex is represented fully in
Device Tree using the simple-card DT binding, this commit updates
mvebu_v7_defconfig to no longer select the Armada 370 DB audio machine
driver, and instead select the appropriate audio controller and codec
drivers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-7-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Kuninori Morimoto [Tue, 4 Nov 2014 01:50:24 +0000 (17:50 -0800)]
ARM: shmobile: multiplatform: add AK4642 support on defconfig
AK4642 is well used audio codec on Renesas reference board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 4 Nov 2014 01:50:13 +0000 (17:50 -0800)]
ARM: shmobile: multiplatform: add Audo DMAC peri peri support on defconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 4 Nov 2014 01:50:00 +0000 (17:50 -0800)]
ARM: shmobile: multiplatform: add R-Car DMAC support on defconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Murali Karicheri [Wed, 29 Oct 2014 20:28:15 +0000 (16:28 -0400)]
ARM: keystone: defconfig: add options to enable PCI controller
This patch enables PCI controller driver for Keystone SoCs by
default.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Murali Karicheri [Wed, 29 Oct 2014 20:28:14 +0000 (16:28 -0400)]
ARM: keystone: add pcie related options
Now that Keystone PCI controller is merged, add pcie related options
by default for keystone architecture so that driver can be enabled in
the build.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Grygorii Strashko [Tue, 1 Apr 2014 15:02:45 +0000 (18:02 +0300)]
ARM: keystone_defconfig: enable mdio and marvell eth phys
Enable MDIO support for Keystone 2 SoCs and also
enable Marvell Ethernet PHYs support for Keystone 2 K2H EVM
which has two 1G Marvell
88E1111-B2 PHYs installed.
For more information see:
- http://www.advantech.com/Support/TI-EVM/EVMK2HX.aspx
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Grygorii Strashko [Mon, 14 Jul 2014 10:24:28 +0000 (13:24 +0300)]
ARM: keystone_defconfig: enable dsp irq and gpio support
Enable DSP IRQ controller and GPIOs support for Keystone 2.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Simon Horman [Thu, 30 Oct 2014 01:59:22 +0000 (10:59 +0900)]
ARM: shmobile: ape6evm: Enable PM Runtime in defconfig
This is consistent with other shmobile defconfigs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Andrew Lunn [Fri, 31 Oct 2014 22:13:33 +0000 (23:13 +0100)]
ARM: config: Add DLINK DIR665 options to multi_v5_defconfig
Enable building of the switch chip driver and the wireless driver
needed by the DLINK DIR665
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: arm@kernel.org
Link: https://lkml.kernel.org/r/1414793613-11798-5-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andrew Lunn [Fri, 31 Oct 2014 22:13:32 +0000 (23:13 +0100)]
ARM: mvebu: Add DLINK DIR665 options to mvebu_v5_defconfig
Enable building of the switch chip driver and the wireless driver
needed by the DLINK DIR665
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-4-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Mon, 20 Oct 2014 01:08:38 +0000 (18:08 -0700)]
Linux 3.18-rc1
Linus Torvalds [Mon, 20 Oct 2014 00:43:06 +0000 (17:43 -0700)]
Merge tag 'arm-soc-fixes-rc1' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Linus Torvalds [Sun, 19 Oct 2014 23:25:56 +0000 (16:25 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Olof Johansson [Sun, 19 Oct 2014 20:39:08 +0000 (13:39 -0700)]
Merge tag 'qcom-dt-for-3.18-3' of git://git./linux/kernel/git/galak/linux-qcom into fixes
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
Olof Johansson [Sun, 19 Oct 2014 20:34:52 +0000 (13:34 -0700)]
Merge tag 'samsung-fixes-2' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Scott Branden [Fri, 17 Oct 2014 03:57:16 +0000 (21:57 -0600)]
MAINTAINERS: corrected bcm2835 search
Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sun, 19 Oct 2014 19:58:22 +0000 (12:58 -0700)]
Merge tag 'ntb-3.18' of git://github.com/jonmason/ntb
Pull ntb (non-transparent bridge) updates from Jon Mason:
"Add support for Haswell NTB split BARs, a debugfs entry for basic
debugging info, and some code clean-ups"
* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
ntb: Adding split BAR support for Haswell platforms
ntb: use errata flag set via DID to implement workaround
ntb: conslidate reading of PPD to move platform detection earlier
ntb: move platform detection to separate function
NTB: debugfs device entry
Linus Torvalds [Sun, 19 Oct 2014 19:50:44 +0000 (12:50 -0700)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
Linus Torvalds [Sun, 19 Oct 2014 19:45:36 +0000 (12:45 -0700)]
Merge tag 'sound-fix-3.18-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes after 3.18 merge.
The urgent one is the fix for kernel panics with linked PCM substream
triggered by the recent nonatomic PCM ops support. Other two fixes
(emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
a new Intel HD-audio controller"
* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
ALSA: emu10k1: Fix deadlock in synth voice lookup
ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88
Linus Torvalds [Sun, 19 Oct 2014 19:40:24 +0000 (12:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
Linus Torvalds [Sun, 19 Oct 2014 19:29:23 +0000 (12:29 -0700)]
Merge tag 'rdma-for-linus' of git://git./linux/kernel/git/roland/infiniband
Pull infiniband/RDMA updates from Roland Dreier:
- large set of iSER initiator improvements
- hardware driver fixes for cxgb4, mlx5 and ocrdma
- small fixes to core midlayer
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
RDMA/cxgb4: Add missing neigh_release in find_route
RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
RDMA/cxgb4: Make c4iw_wr_log_size_order static
IB/core: Fix XRC race condition in ib_uverbs_open_qp
IB/core: Clear AH attr variable to prevent garbage data
RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
RDMA/ocrdma: Remove a unused-label warning
RDMA/ocrdma: Convert kernel VA to PA for mmap in user
RDMA/ocrdma: Get vlan tag from ib_qp_attrs
RDMA/ocrdma: Add default GID at index 0
IB/mlx5, iser, isert: Add Signature API additions
Target/iser: Centralize ib_sig_domain setting
IB/iser: Centralize ib_sig_domain settings
IB/mlx5: Use extended internal signature layout
IB/iser: Set IP_CSUM as default guard type
IB/iser: Remove redundant assignment
IB/mlx5: Use enumerations for PI copy mask
...
Linus Torvalds [Sun, 19 Oct 2014 18:55:41 +0000 (11:55 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull more perf updates from Ingo Molnar:
"A second (and last) round of late coming fixes and changes, almost all
of them in perf tooling:
User visible tooling changes:
- Add period data column and make it default in 'perf script' (Jiri
Olsa)
- Add a visual cue for toggle zeroing of samples in 'perf top'
(Taeung Song)
- Improve callchains when using libunwind (Namhyung Kim)
Tooling fixes and infrastructure changes:
- Fix for double free in 'perf stat' when using some specific invalid
command line combo (Yasser Shalabi)
- Fix off-by-one bugs in map->end handling (Stephane Eranian)
- Fix off-by-one bug in maps__find(), also related to map->end
handling (Namhyung Kim)
- Make struct symbol->end be the first addr after the symbol range,
to make it match the convention used for struct map->end. (Arnaldo
Carvalho de Melo)
- Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
live' (Jiri Olsa)
- Fix python test build by moving callchain_param to an object linked
into the python binding (Jiri Olsa)
- Document sysfs events/ interfaces (Cody P Schafer)
- Fix typos in perf/Documentation (Masanari Iida)
- Add missing 'struct option' forward declaration (Arnaldo Carvalho
de Melo)
- Add option to copy events when queuing for sorting across cpu
buffers and enable it for 'perf kvm stat live', to avoid having
events left in the queue pointing to the ring buffer be rewritten
in high volume sessions. (Alexander Yarygin, improving work done
by David Ahern):
- Do not include a struct hists per perf_evsel, untangling the
histogram code from perf_evsel, to pave the way for exporting a
minimalistic tools/lib/api/perf/ library usable by tools/perf and
initially by the rasd daemon being developed by Borislav Petkov,
Robert Richter and Jean Pihet. (Arnaldo Carvalho de Melo)
- Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
thread maps mean syswide monitoring, reducing the boilerplate for
tools that only want system wide mode. (Arnaldo Carvalho de Melo)
- Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
should be just a front end for exit + free (Arnaldo Carvalho de
Melo)
- Add support to new style format of kernel PMU event. (Kan Liang)
and other misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
perf script: Add period as a default output column
perf script: Add period data column
perf evsel: No need to drag util/cgroup.h
perf evlist: Add missing 'struct option' forward declaration
perf evsel: Move exit stuff from __delete to __exit
kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
perf kvm stat live: Enable events copying
perf session: Add option to copy events when queueing
perf Documentation: Fix typos in perf/Documentation
perf trace: Use thread_{,_set}_priv helpers
perf kvm: Use thread_{,_set}_priv helpers
perf callchain: Create an address space per thread
perf report: Set callchain_param.record_mode for future use
perf evlist: Fix for double free in tools/perf stat
perf test: Add test case for pmu event new style format
perf tools: Add support to new style format of kernel PMU event
perf tools: Parse the pmu event prefix and suffix
Revert "perf tools: Default to cpu// for events v5"
perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
perf Documentation: sysfs events/ interfaces
...
Linus Torvalds [Sun, 19 Oct 2014 18:46:09 +0000 (11:46 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
"Here we have two bug fixes:
1) The current thread's fault_code is not setup properly upon entry to
do_sparc64_fault() in some paths, leading to spurious SIGBUS.
2) Don't use a zero length array at the end of thread_info on sparc64,
otherwise end_of_stack() isn't right"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Do not define thread fpregs save area as zero-length array.
sparc64: Fix corrupted thread fault code.
Linus Torvalds [Sun, 19 Oct 2014 18:41:57 +0000 (11:41 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"A quick batch of bug fixes:
1) Fix build with IPV6 disabled, from Eric Dumazet.
2) Several more cases of caching SKB data pointers across calls to
pskb_may_pull(), thus referencing potentially free'd memory. From
Li RongQing.
3) DSA phy code tests operation presence improperly, instead of going:
if (x->ops->foo)
r = x->ops->foo(args);
it was going:
if (x->ops->foo(args))
r = x->ops->foo(args);
Fix from Andew Lunn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Net: DSA: Fix checking for get_phy_flags function
ipv6: fix a potential use after free in sit.c
ipv6: fix a potential use after free in ip6_offload.c
ipv4: fix a potential use after free in gre_offload.c
tcp: fix build error if IPv6 is not enabled
Andrew Lunn [Sun, 19 Oct 2014 14:41:47 +0000 (16:41 +0200)]
Net: DSA: Fix checking for get_phy_flags function
The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes:
6819563e646a ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 19 Oct 2014 03:12:33 +0000 (23:12 -0400)]
sparc64: Do not define thread fpregs save area as zero-length array.
This breaks the stack end corruption detection facility.
What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.
"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.
So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.
Fix this by making the size explicit.
Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves. So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 19 Oct 2014 03:03:09 +0000 (23:03 -0400)]
sparc64: Fix corrupted thread fault code.
Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.
Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:
1) For pre-hypervisor TLB protection violation traps, if we took
the 'winfix_trampoline' path we wouldn't have %g4 initialized
with the FAULT_CODE_* value yet. Resulting in using the
TLB_TAG_ACCESS register address value instead.
2) In the TSB miss path, when we notice that we are going to use a
hugepage mapping, but we haven't allocated the hugepage TSB yet, we
still have to take the window fixup case into consideration and
in that particular path we leave %g4 not setup properly.
Errors on this sort were largely invisible previously, but after
commit
4ccb9272892c33ef1c19a783cfa87103b30c2784 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.
FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.
Fixes:
4ccb9272892c ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 19 Oct 2014 01:11:04 +0000 (18:11 -0700)]
Merge branch 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
Linus Torvalds [Sun, 19 Oct 2014 01:03:02 +0000 (18:03 -0700)]
Merge tag 'fbdev-3.18' of git://git./linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- new 6x10 font
- various small fixes and cleanups
* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
fonts: Add 6x10 font
videomode: provide dummy inline functions for !CONFIG_OF
video/atmel_lcdfb: Introduce regulator support
fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
framebuffer: fix screen corruption when copying
framebuffer: fix border color
arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
video: fbdev: use %*ph specifier to dump small buffers
video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
video: fbdev: au1200fb: delete double assignment
video: fbdev: sis: delete double assignment
...
Linus Torvalds [Sat, 18 Oct 2014 21:32:31 +0000 (14:32 -0700)]
Merge tag 'kvm-arm-for-3.18-take-2' of git://git./linux/kernel/git/kvmarm/kvmarm
Pull second batch of changes for KVM/{arm,arm64} from Marc Zyngier:
"The most obvious thing is the sizeable MMU changes to support 48bit
VAs on arm64.
Summary:
- support for 48bit IPA and VA (EL2)
- a number of fixes for devices mapped into guests
- yet another VGIC fix for BE
- a fix for CPU hotplug
- a few compile fixes (disabled VGIC, strict mm checks)"
[ I'm pulling directly from Marc at the request of Paolo Bonzini, whose
backpack was stolen at Düsseldorf airport and will do new keys and
rebuild his web of trust. - Linus ]
* tag 'kvm-arm-for-3.18-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
arm/arm64: KVM: Fix BE accesses to GICv2 EISR and ELRSR regs
arm: kvm: STRICT_MM_TYPECHECKS fix for user_mem_abort
arm/arm64: KVM: Ensure memslots are within KVM_PHYS_SIZE
arm64: KVM: Implement 48 VA support for KVM EL2 and Stage-2
arm/arm64: KVM: map MMIO regions at creation time
arm64: kvm: define PAGE_S2_DEVICE as read-only by default
ARM: kvm: define PAGE_S2_DEVICE as read-only by default
arm/arm64: KVM: add 'writable' parameter to kvm_phys_addr_ioremap
arm/arm64: KVM: fix potential NULL dereference in user_mem_abort()
arm/arm64: KVM: use __GFP_ZERO not memset() to get zeroed pages
ARM: KVM: fix vgic-disabled build
arm: kvm: fix CPU hotplug
Linus Torvalds [Sat, 18 Oct 2014 21:24:36 +0000 (14:24 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the MIPS pull request for the next kernel:
- Zubair's patch series adds CMA support for MIPS. Doing so it also
touches ARM64 and x86.
- remove the last instance of IRQF_DISABLED from arch/mips
- updates to two of the MIPS defconfig files.
- cleanup of how cache coherency bits are handled on MIPS and
implement support for write-combining.
- platform upgrades for Alchemy
- move MIPS DTS files to arch/mips/boot/dts/"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (24 commits)
MIPS: ralink: remove deprecated IRQF_DISABLED
MIPS: pgtable.h: Implement the pgprot_writecombine function for MIPS
MIPS: cpu-probe: Set the write-combine CCA value on per core basis
MIPS: pgtable-bits: Define the CCA bit for WC writes on Ingenic cores
MIPS: pgtable-bits: Move the CCA bits out of the core's ifdef blocks
MIPS: DMA: Add cma support
x86: use generic dma-contiguous.h
arm64: use generic dma-contiguous.h
asm-generic: Add dma-contiguous.h
MIPS: BPF: Add new emit_long_instr macro
MIPS: ralink: Move device-trees to arch/mips/boot/dts/
MIPS: Netlogic: Move device-trees to arch/mips/boot/dts/
MIPS: sead3: Move device-trees to arch/mips/boot/dts/
MIPS: Lantiq: Move device-trees to arch/mips/boot/dts/
MIPS: Octeon: Move device-trees to arch/mips/boot/dts/
MIPS: Add support for building device-tree binaries
MIPS: Create common infrastructure for building built-in device-trees
MIPS: SEAD3: Enable DEVTMPFS
MIPS: SEAD3: Regenerate defconfigs
MIPS: Alchemy: DB1300: Add touch penirq support
...
Linus Torvalds [Sat, 18 Oct 2014 21:22:32 +0000 (14:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mpe/linux
Pull powerpc fix from Michael Ellerman:
"There was a bit of a misunderstanding between us and the ARM guys in
the device tree PCI code, which is breaking virtio on powerpc.
This is the minimal fix until we can sort it out properly"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/pci: Fix IO space breakage after of_pci_range_to_resource() change
Linus Torvalds [Sat, 18 Oct 2014 20:39:19 +0000 (13:39 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs/smb3 updates from Steve French:
"Improved SMB3 support (symlink and device emulation, and remapping by
default the 7 reserved posix characters) and a workaround for cifs
mounts to Mac (working around a commonly encountered Mac server bug)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] Remove obsolete comment
Check minimum response length on query_network_interface
Workaround Mac server problem
Remap reserved posix characters by default (part 3/3)
Allow conversion of characters in Mac remap range (part 2)
Allow conversion of characters in Mac remap range. Part 1
mfsymlinks support for SMB2.1/SMB3. Part 2 query symlink
Add mfsymlinks support for SMB2.1/SMB3. Part 1 create symlink
Allow mknod and mkfifo on SMB2/SMB3 mounts
add defines for two new file attributes
Linus Torvalds [Sat, 18 Oct 2014 20:37:19 +0000 (13:37 -0700)]
Merge tag 'dlm-3.18' of git://git./linux/kernel/git/teigland/linux-dlm
Pull dlm fix from David Teigland:
"This includes a single commit fixing a missing endian conversion"
* tag 'dlm-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: fix missing endian conversion of rcom_status flags
Linus Torvalds [Sat, 18 Oct 2014 20:32:17 +0000 (13:32 -0700)]
Merge branch 'for-linus-update' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs data corruption fix from Chris Mason:
"I'm testing a pull with more fixes, but wanted to get this one out so
Greg can pick it up.
The corruption isn't easy to hit, you have to do a readonly snapshot
and have orphans in the snapshot. But my review and testing missed
the bug. Filipe has added a better xfstest to cover it"
* 'for-linus-update' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Revert "Btrfs: race free update of commit root for ro snapshots"
Linus Torvalds [Sat, 18 Oct 2014 20:25:03 +0000 (13:25 -0700)]
Merge tag 'please-pull-pstore' of git://git./linux/kernel/git/aegl/linux
Pull pstore fix from Tony Luck:
"Ensure unique filenames in pstore"
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: Fix duplicate {console,ftrace}-efi entries
Linus Torvalds [Sat, 18 Oct 2014 19:54:46 +0000 (12:54 -0700)]
Merge git://git./linux/kernel/git/aia21/ntfs
Pull NTFS update from Anton Altaparmakov:
"Here is a small NTFS update notably implementing FIBMAP ioctl for NTFS
by adding the bmap address space operation. People seem to still want
FIBMAP"
* git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs:
NTFS: Bump version to 2.1.31.
NTFS: Add bmap address space operation needed for FIBMAP ioctl.
NTFS: Remove changelog from Documentation/filesystems/ntfs.txt.
NTFS: Split ntfs_aops into ntfs_normal_aops and ntfs_compressed_aops in preparation for them diverging.
Linus Torvalds [Sat, 18 Oct 2014 19:52:08 +0000 (12:52 -0700)]
Merge tag 'nfs-for-3.18-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix an uninitialised pointer Oops in the writeback error path
- fix a bogus warning (and early exit from the loop) in nfs_generic_pgio()
Features:
- Add NFSv4.2 SEEK feature and client support for lseek(SEEK_HOLE/SEEK_DATA)
Other fixes:
- pnfs: replace broken pnfs_put_lseg_async
- Remove dead prototype for nfs4_insert_deviceid_node"
* tag 'nfs-for-3.18-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a bogus warning in nfs_generic_pgio
NFS: Fix an uninitialised pointer Oops in the writeback error path
NFSv4.1/pnfs: replace broken pnfs_put_lseg_async
NFSv4: Remove dead prototype for nfs4_insert_deviceid_node()
NFS: Implement SEEK
Linus Torvalds [Sat, 18 Oct 2014 19:25:30 +0000 (12:25 -0700)]
Merge tag 'dm-3.18' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device-mapper updates from Mike Snitzer:
"I rebased the DM tree ontop of linux-block.git's 'for-3.18/core' at
the beginning of October because DM core now depends on the newly
introduced bioset_create_nobvec() interface.
Summary:
- fix DM's long-standing excessive use of memory by leveraging the
new bioset_create_nobvec() interface when creating the DM's bioset
- fix a few bugs in dm-bufio and dm-log-userspace
- add DM core support for a DM multipath use-case that requires
loading DM tables that contain devices that have failed (by
allowing active and inactive DM tables to share dm_devs)
- add discard support to the DM raid target; like MD raid456 the user
must opt-in to raid456 discard support be specifying the
devices_handle_discard_safely=Y module param"
* tag 'dm-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm log userspace: fix memory leak in dm_ulog_tfr_init failure path
dm bufio: when done scanning return from __scan immediately
dm bufio: update last_accessed when relinking a buffer
dm raid: add discard support for RAID levels 4, 5 and 6
dm raid: add discard support for RAID levels 1 and 10
dm: allow active and inactive tables to share dm_devs
dm mpath: stop queueing IO when no valid paths exist
dm: use bioset_create_nobvec()
dm: remove nr_iovecs parameter from alloc_tio()
Linus Torvalds [Sat, 18 Oct 2014 19:12:45 +0000 (12:12 -0700)]
Merge branch 'for-3.18/drivers' of git://git.kernel.dk/linux-block
Pull block layer driver update from Jens Axboe:
"This is the block driver pull request for 3.18. Not a lot in there
this round, and nothing earth shattering.
- A round of drbd fixes from the linbit team, and an improvement in
asender performance.
- Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and
hd from Michael Opdenacker.
- Disable entropy collection from flash devices by default, from Mike
Snitzer.
- A small collection of xen blkfront/back fixes from Roger Pau Monné
and Vitaly Kuznetsov"
* 'for-3.18/drivers' of git://git.kernel.dk/linux-block:
block: disable entropy contributions for nonrot devices
xen, blkfront: factor out flush-related checks from do_blkif_request()
xen-blkback: fix leak on grant map error path
xen/blkback: unmap all persistent grants when frontend gets disconnected
rsxx: Remove deprecated IRQF_DISABLED
block: hd: remove deprecated IRQF_DISABLED
drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks
drbd: compute the end before rb_insert_augmented()
drbd: Add missing newline in resync progress display in /proc/drbd
drbd: reduce lock contention in drbd_worker
drbd: Improve asender performance
drbd: Get rid of the WORK_PENDING macro
drbd: Get rid of the __no_warn and __cond_lock macros
drbd: Avoid inconsistent locking warning
drbd: Remove superfluous newline from "resync_extents" debugfs entry.
drbd: Use consistent names for all the bi_end_io callbacks
drbd: Use better variable names
Linus Torvalds [Sat, 18 Oct 2014 18:53:51 +0000 (11:53 -0700)]
Merge branch 'for-3.18/core' of git://git.kernel.dk/linux-block
Pull core block layer changes from Jens Axboe:
"This is the core block IO pull request for 3.18. Apart from the new
and improved flush machinery for blk-mq, this is all mostly bug fixes
and cleanups.
- blk-mq timeout updates and fixes from Christoph.
- Removal of REQ_END, also from Christoph. We pass it through the
->queue_rq() hook for blk-mq instead, freeing up one of the request
bits. The space was overly tight on 32-bit, so Martin also killed
REQ_KERNEL since it's no longer used.
- blk integrity updates and fixes from Martin and Gu Zheng.
- Update to the flush machinery for blk-mq from Ming Lei. Now we
have a per hardware context flush request, which both cleans up the
code should scale better for flush intensive workloads on blk-mq.
- Improve the error printing, from Rob Elliott.
- Backing device improvements and cleanups from Tejun.
- Fixup of a misplaced rq_complete() tracepoint from Hannes.
- Make blk_get_request() return error pointers, fixing up issues
where we NULL deref when a device goes bad or missing. From Joe
Lawrence.
- Prep work for drastically reducing the memory consumption of dm
devices from Junichi Nomura. This allows creating clone bio sets
without preallocating a lot of memory.
- Fix a blk-mq hang on certain combinations of queue depths and
hardware queues from me.
- Limit memory consumption for blk-mq devices for crash dump
scenarios and drivers that use crazy high depths (certain SCSI
shared tag setups). We now just use a single queue and limited
depth for that"
* 'for-3.18/core' of git://git.kernel.dk/linux-block: (58 commits)
block: Remove REQ_KERNEL
blk-mq: allocate cpumask on the home node
bio-integrity: remove the needless fail handle of bip_slab creating
block: include func name in __get_request prints
block: make blk_update_request print prefix match ratelimited prefix
blk-merge: don't compute bi_phys_segments from bi_vcnt for cloned bio
block: fix alignment_offset math that assumes io_min is a power-of-2
blk-mq: Make bt_clear_tag() easier to read
blk-mq: fix potential hang if rolling wakeup depth is too high
block: add bioset_create_nobvec()
block: use bio_clone_fast() in blk_rq_prep_clone()
block: misplaced rq_complete tracepoint
sd: Honor block layer integrity handling flags
block: Replace strnicmp with strncasecmp
block: Add T10 Protection Information functions
block: Don't merge requests if integrity flags differ
block: Integrity checksum flag
block: Relocate bio integrity flags
block: Add a disk flag to block integrity profile
block: Add prefix to block integrity profile flags
...
Linus Torvalds [Sat, 18 Oct 2014 18:48:03 +0000 (11:48 -0700)]
Merge tag 'for-linus-
20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-
20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
Linus Torvalds [Sat, 18 Oct 2014 18:39:52 +0000 (11:39 -0700)]
Merge tag 'md/3.18' of git://neil.brown.name/md
Pull md updates from Neil Brown:
- a few minor bug fixes
- quite a lot of code tidy-up and simplification
- remove PRINT_RAID_DEBUG ioctl. I'm fairly sure it is unused, and it
isn't particularly useful.
* tag 'md/3.18' of git://neil.brown.name/md: (21 commits)
lib/raid6: Add log level to printks
md: move EXPORT_SYMBOL to after function in md.c
md: discard PRINT_RAID_DEBUG ioctl
md: remove MD_BUG()
md: clean up 'exit' labels in md_ioctl().
md: remove unnecessary test for MD_MAJOR in md_ioctl()
md: don't allow "-sync" to be set for device in an active array.
md: remove unwanted white space from md.c
md: don't start resync thread directly from md thread.
md: Just use RCU when checking for overlap between arrays.
md: avoid potential long delay under pers_lock
md: simplify export_array()
md: discard find_rdev_nr in favour of find_rdev_nr_rcu
md: use wait_event() to simplify md_super_wait()
md: be more relaxed about stopping an array which isn't started.
md/raid1: process_checks doesn't use its return value.
md/raid5: fix init_stripe() inconsistencies
md/raid10: another memory leak due to reshape.
md: use set_bit/clear_bit instead of shift/mask for bi_flags changes.
md/raid1: minor typos and reformatting.
...
Linus Torvalds [Sat, 18 Oct 2014 17:26:10 +0000 (10:26 -0700)]
Merge branch 'for-linus2' of git://git./linux/kernel/git/jmorris/linux-security
Pull selinux fix from James Morris:
"Fix for a list corruption bug in the SELinux code"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix inode security list corruption
Linus Torvalds [Sat, 18 Oct 2014 17:25:09 +0000 (10:25 -0700)]
Merge tag 'virtio-next-for-linus' of git://git./linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
Linus Torvalds [Sat, 18 Oct 2014 17:24:26 +0000 (10:24 -0700)]
Merge tag 'modules-next-for-linus' of git://git./linux/kernel/git/rusty/linux
Pull module fix from Rusty Russell:
"A single panic fix for a rare race, stable CC'd"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modules, lock around setting of MODULE_STATE_UNFORMED
Jonathan Corbet [Fri, 17 Oct 2014 12:59:26 +0000 (08:59 -0400)]
MAINTAINERS: Become the docs maintainer
It seems it's my turn to be the documentation maintainer for a bit. My
plan is to work to ensure that docs patches don't fall through the cracks;
I assume most changes will continue to flow through subsystem-specific
trees.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Lutomirski [Wed, 8 Oct 2014 16:02:13 +0000 (09:02 -0700)]
x86,kvm,vmx: Preserve CR4 across VM entry
CR4 isn't constant; at least the TSD and PCE bits can vary.
TBH, treating CR0 and CR3 as constant scares me a bit, too, but it looks
like it's correct.
This adds a branch and a read from cr4 to each vm entry. Because it is
extremely likely that consecutive entries into the same vcpu will have
the same host cr4 value, this fixes up the vmcs instead of restoring cr4
after the fact. A subsequent patch will add a kernel-wide cr4 shadow,
reducing the overhead in the common case to just two memory reads and a
branch.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li RongQing [Sat, 18 Oct 2014 09:33:38 +0000 (17:33 +0800)]
ipv6: fix a potential use after free in sit.c
pskb_may_pull() maybe change skb->data and make iph pointer oboslete,
fix it by geting ip header length directly.
Fixes:
ca15a078 (sit: generate icmpv6 error when receiving icmpv4 error)
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Sat, 18 Oct 2014 09:27:42 +0000 (17:27 +0800)]
ipv6: fix a potential use after free in ip6_offload.c
pskb_may_pull() maybe change skb->data and make opth pointer oboslete,
so set the opth again
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Sat, 18 Oct 2014 09:26:04 +0000 (17:26 +0800)]
ipv4: fix a potential use after free in gre_offload.c
pskb_may_pull() may change skb->data and make greh pointer oboslete;
so need to reassign greh;
but since first calling pskb_may_pull already ensured that skb->data
has enough space for greh, so move the reference of greh before second
calling pskb_may_pull(), to avoid reassign greh.
Fixes:
7a7ffbabf9("ipv4: fix tunneled VM traffic over hw VXLAN/GRE GSO NIC")
Cc: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 18 Oct 2014 15:34:37 +0000 (08:34 -0700)]
tcp: fix build error if IPv6 is not enabled
$ make M=net/ipv4
CC net/ipv4/route.o
In file included from net/ipv4/route.c:102:0:
include/net/tcp.h: In function ‘tcp_v6_iif’:
include/net/tcp.h:738:32: error: ‘union <anonymous>’ has no member named ‘h6’
return TCP_SKB_CB(skb)->header.h6.iif;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes:
870c3151382c ("ipv6: introduce tcp_v6_iif()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 18 Oct 2014 16:31:37 +0000 (09:31 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
Linus Torvalds [Sat, 18 Oct 2014 16:30:41 +0000 (09:30 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull Sparc bugfix from David Miller:
"Sparc64 AES ctr mode bug fix"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix FPU register corruption with AES crypto offload.
Linus Torvalds [Sat, 18 Oct 2014 16:29:59 +0000 (09:29 -0700)]
Merge git://git./linux/kernel/git/davem/ide
Pull IDE cleanup from David Miller:
"One IDE driver cleanup"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
Drivers: ide: Remove typedef atiixp_ide_timing
Catalin Marinas [Fri, 17 Oct 2014 16:38:49 +0000 (17:38 +0100)]
futex: Ensure get_futex_key_refs() always implies a barrier
Commit
b0c29f79ecea (futexes: Avoid taking the hb->lock if there's
nothing to wake up) changes the futex code to avoid taking a lock when
there are no waiters. This code has been subsequently fixed in commit
11d4616bd07f (futex: revert back to the explicit waiter counting code).
Both the original commit and the fix-up rely on get_futex_key_refs() to
always imply a barrier.
However, for private futexes, none of the cases in the switch statement
of get_futex_key_refs() would be hit and the function completes without
a memory barrier as required before checking the "waiters" in
futex_wake() -> hb_waiters_pending(). The consequence is a race with a
thread waiting on a futex on another CPU, allowing the waker thread to
read "waiters == 0" while the waiter thread to have read "futex_val ==
locked" (in kernel).
Without this fix, the problem (user space deadlocks) can be seen with
Android bionic's mutex implementation on an arm64 multi-cluster system.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Matteo Franchin <Matteo.Franchin@arm.com>
Fixes:
b0c29f79ecea (futexes: Avoid taking the hb->lock if there's nothing to wake up)
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Sat, 18 Oct 2014 07:04:02 +0000 (09:04 +0200)]
Merge tag 'perf-core-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
* Add period data column and make it default in 'perf script' (Jiri Olsa)
Infrastructure changes:
* Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
should be just a front end for exit + free (Arnaldo Carvalho de Melo)
* Add missing 'struct option' forward declaration (Arnaldo Carvalho de Melo)
* No need to drag util/cgroup.h into evsel.h (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Eric Dumazet [Fri, 17 Oct 2014 19:45:55 +0000 (12:45 -0700)]
bna: fix skb->truesize underestimation
skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.
skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 17 Oct 2014 23:02:13 +0000 (16:02 -0700)]
net: dsa: add includes for ethtool and phy_fixed definitions
net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.
Fixes:
ec9436baedb6 ("net: dsa: allow drivers to do link adjustment")
Fixes:
ce31b31c68e7 ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Fri, 17 Oct 2014 20:56:31 +0000 (13:56 -0700)]
openvswitch: Set flow-key members.
This patch adds missing memset which are required to initialize
flow key member. For example for IP flow we need to initialize
ip.frag for all cases.
Found by inspection.
This bug is introduced by commit
0714812134d7dcadeb7ecfbfeb18788aa7e1eaac
("openvswitch: Eliminate memset() from flow_extract").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabian Frederick [Fri, 17 Oct 2014 20:00:22 +0000 (22:00 +0200)]
netrom: use linux/uaccess.h
replace asm/uaccess.h by linux/uaccess.h
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Fri, 17 Oct 2014 19:30:58 +0000 (12:30 -0700)]
dsa: Fix conversion from host device to mii bus
Commit
b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<
ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD
406783067 PUD
406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<
ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<
ffffffff81781de3>] mutex_lock+0x23/0x37
[<
ffffffff81533244>] mdiobus_read+0x34/0x60
[<
ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<
ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes:
b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Fri, 17 Oct 2014 19:25:28 +0000 (15:25 -0400)]
tipc: fix bug in bundled buffer reception
In commit
ec8a2e5621db2da24badb3969eda7fd359e1869f ("tipc: same receive
code path for connection protocol and data messages") we omitted the
the possiblilty that an arriving message extracted from a bundle buffer
may be a multicast message. Such messages need to be to be delivered to
the socket via a separate function, tipc_sk_mcast_rcv(). As a result,
small multicast messages arriving as members of a bundle buffer will be
silently dropped.
This commit corrects the error by considering this case in the function
tipc_link_bundle_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 17 Oct 2014 16:17:20 +0000 (09:17 -0700)]
ipv6: introduce tcp_v6_iif()
Commit
971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line
misses") added a regression for SO_BINDTODEVICE on IPv6.
This is because we still use inet6_iif() which expects that IP6 control
block is still at the beginning of skb->cb[]
This patch adds tcp_v6_iif() helper and uses it where necessary.
Because __inet6_lookup_skb() is used by TCP and DCCP, we add an iif
parameter to it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes:
971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 17 Oct 2014 14:32:25 +0000 (15:32 +0100)]
sfc: add support for skb->xmit_more
Don't ring the doorbell, and don't do PIO. This will also prevent
TX Push, because there will be more than one buffer waiting when
the doorbell is rung.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Fri, 17 Oct 2014 08:55:08 +0000 (16:55 +0800)]
r8152: return -EBUSY for runtime suspend
Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Fri, 17 Oct 2014 08:53:47 +0000 (16:53 +0800)]
ipv4: fix a potential use after free in fou.c
pskb_may_pull() maybe change skb->data and make uh pointer oboslete,
so reload uh and guehdr
Fixes:
37dd0247 ("gue: Receive side for Generic UDP Encapsulation")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / GitHub / LineageOS / G12 / android_kernel_amlogic_linux-4.9.git / log