From: Mariusz Bialonczyk <manio@skyboo.net>
Date: Tue, 29 Mar 2016 16:41:38 +0000 (+0200)
Subject: w1: enable active pullup for DS2482 by default
X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=f704938c0ef1e3224e66b16d5b358f02cd351240;p=GitHub%2Fmoto-9609%2Fandroid_kernel_motorola_exynos9610.git

w1: enable active pullup for DS2482 by default

This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.

>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."

According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.

This active pullup can be manually disabled using the introduced
module parameter:
  active_pullup = 0

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---

diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c
index b05e8fefbabd..2e30db1b1a43 100644
--- a/drivers/w1/masters/ds2482.c
+++ b/drivers/w1/masters/ds2482.c
@@ -23,6 +23,19 @@
 #include "../w1.h"
 #include "../w1_int.h"
 
+/**
+ * Allow the active pullup to be disabled, default is enabled.
+ *
+ * Note from the DS2482 datasheet:
+ * The APU bit controls whether an active pullup (controlled slew-rate
+ * transistor) or a passive pullup (Rwpu resistor) will be used to drive
+ * a 1-Wire line from low to high. When APU = 0, active pullup is disabled
+ * (resistor mode). Active Pullup should always be selected unless there is
+ * only a single slave on the 1-Wire line.
+ */
+static int ds2482_active_pullup = 1;
+module_param_named(active_pullup, ds2482_active_pullup, int, 0644);
+
 /**
  * The DS2482 registers - there are 3 registers that are addressed by a read
  * pointer. The read pointer is set by the last command executed.
@@ -138,6 +151,9 @@ struct ds2482_data {
  */
 static inline u8 ds2482_calculate_config(u8 conf)
 {
+	if (ds2482_active_pullup)
+		conf |= DS2482_REG_CFG_APU;
+
 	return conf | ((~conf & 0x0f) << 4);
 }
 
@@ -546,6 +562,8 @@ static int ds2482_remove(struct i2c_client *client)
 
 module_i2c_driver(ds2482_driver);
 
+MODULE_PARM_DESC(active_pullup, "Active pullup (apply to all buses): " \
+				"0-disable, 1-enable (default)");
 MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
 MODULE_DESCRIPTION("DS2482 driver");
 MODULE_LICENSE("GPL");