From: Andy Fleming Date: Sat, 24 Sep 2005 02:54:21 +0000 (-0400) Subject: [netdrvr gianfar] use new phy layer X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=bb40dcbb0fcebe1df08ba261483fcc38b307d063;p=GitHub%2Fmt8127%2Fandroid_kernel_alcatel_ttab.git [netdrvr gianfar] use new phy layer Signed-off-by: Andy Fleming Signed-off-by: Jeff Garzik --- diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index ff3fccd7513b..4739a63601eb 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -2075,6 +2075,8 @@ config SPIDER_NET config GIANFAR tristate "Gianfar Ethernet" depends on 85xx || 83xx + select PHYLIB + select PHYCONTROL help This driver supports the Gigabit TSEC on the MPC85xx family of chips, and the FEC on the 8540 diff --git a/drivers/net/Makefile b/drivers/net/Makefile index e6acba68923a..39b17cb4f86e 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -13,7 +13,7 @@ obj-$(CONFIG_CHELSIO_T1) += chelsio/ obj-$(CONFIG_BONDING) += bonding/ obj-$(CONFIG_GIANFAR) += gianfar_driver.o -gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_phy.o +gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_mii.o # # link order important here diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 6518334b9280..ae5a2ed3b264 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -29,12 +29,7 @@ * define the configuration needed by the board are defined in a * board structure in arch/ppc/platforms (though I do not * discount the possibility that other architectures could one - * day be supported. One assumption the driver currently makes - * is that the PHY is configured in such a way to advertise all - * capabilities. This is a sensible default, and on certain - * PHYs, changing this default encounters substantial errata - * issues. Future versions may remove this requirement, but for - * now, it is best for the firmware to ensure this is the case. + * day be supported. * * The Gianfar Ethernet Controller uses a ring of buffer * descriptors. The beginning is indicated by a register @@ -47,7 +42,7 @@ * corresponding bit in the IMASK register is also set (if * interrupt coalescing is active, then the interrupt may not * happen immediately, but will wait until either a set number - * of frames or amount of time have passed.). In NAPI, the + * of frames or amount of time have passed). In NAPI, the * interrupt handler will signal there is work to be done, and * exit. Without NAPI, the packet(s) will be handled * immediately. Both methods will start at the last known empty @@ -75,6 +70,7 @@ #include #include #include +#include #include #include #include @@ -97,9 +93,11 @@ #include #include #include +#include +#include #include "gianfar.h" -#include "gianfar_phy.h" +#include "gianfar_mii.h" #define TX_TIMEOUT (1*HZ) #define SKB_ALLOC_TIMEOUT 1000000 @@ -113,9 +111,8 @@ #endif const char gfar_driver_name[] = "Gianfar Ethernet"; -const char gfar_driver_version[] = "1.1"; +const char gfar_driver_version[] = "1.2"; -int startup_gfar(struct net_device *dev); static int gfar_enet_open(struct net_device *dev); static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev); static void gfar_timeout(struct net_device *dev); @@ -126,17 +123,13 @@ static int gfar_set_mac_address(struct net_device *dev); static int gfar_change_mtu(struct net_device *dev, int new_mtu); static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs); static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs); -static irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs); static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs); -static void gfar_phy_change(void *data); -static void gfar_phy_timer(unsigned long data); static void adjust_link(struct net_device *dev); static void init_registers(struct net_device *dev); static int init_phy(struct net_device *dev); static int gfar_probe(struct device *device); static int gfar_remove(struct device *device); -void free_skb_resources(struct gfar_private *priv); +static void free_skb_resources(struct gfar_private *priv); static void gfar_set_multi(struct net_device *dev); static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr); #ifdef CONFIG_GFAR_NAPI @@ -144,7 +137,6 @@ static int gfar_poll(struct net_device *dev, int *budget); #endif int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit); static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int length); -static void gfar_phy_startup_timer(unsigned long data); static void gfar_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp); static void gfar_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid); @@ -162,6 +154,9 @@ int gfar_uses_fcb(struct gfar_private *priv) else return 0; } + +/* Set up the ethernet device structure, private data, + * and anything else we need before we start */ static int gfar_probe(struct device *device) { u32 tempval; @@ -175,7 +170,7 @@ static int gfar_probe(struct device *device) einfo = (struct gianfar_platform_data *) pdev->dev.platform_data; - if (einfo == NULL) { + if (NULL == einfo) { printk(KERN_ERR "gfar %d: Missing additional data!\n", pdev->id); @@ -185,7 +180,7 @@ static int gfar_probe(struct device *device) /* Create an ethernet device instance */ dev = alloc_etherdev(sizeof (*priv)); - if (dev == NULL) + if (NULL == dev) return -ENOMEM; priv = netdev_priv(dev); @@ -207,20 +202,11 @@ static int gfar_probe(struct device *device) priv->regs = (struct gfar *) ioremap(r->start, sizeof (struct gfar)); - if (priv->regs == NULL) { + if (NULL == priv->regs) { err = -ENOMEM; goto regs_fail; } - /* Set the PHY base address */ - priv->phyregs = (struct gfar *) - ioremap(einfo->phy_reg_addr, sizeof (struct gfar)); - - if (priv->phyregs == NULL) { - err = -ENOMEM; - goto phy_regs_fail; - } - spin_lock_init(&priv->lock); dev_set_drvdata(device, dev); @@ -386,12 +372,10 @@ static int gfar_probe(struct device *device) return 0; register_fail: - iounmap((void *) priv->phyregs); -phy_regs_fail: iounmap((void *) priv->regs); regs_fail: free_netdev(dev); - return -ENOMEM; + return err; } static int gfar_remove(struct device *device) @@ -402,108 +386,41 @@ static int gfar_remove(struct device *device) dev_set_drvdata(device, NULL); iounmap((void *) priv->regs); - iounmap((void *) priv->phyregs); free_netdev(dev); return 0; } -/* Configure the PHY for dev. - * returns 0 if success. -1 if failure +/* Initializes driver's PHY state, and attaches to the PHY. + * Returns 0 on success. */ static int init_phy(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); - struct phy_info *curphy; - unsigned int timeout = PHY_INIT_TIMEOUT; - struct gfar *phyregs = priv->phyregs; - struct gfar_mii_info *mii_info; - int err; + uint gigabit_support = + priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ? + SUPPORTED_1000baseT_Full : 0; + struct phy_device *phydev; priv->oldlink = 0; priv->oldspeed = 0; priv->oldduplex = -1; - mii_info = kmalloc(sizeof(struct gfar_mii_info), - GFP_KERNEL); - - if(NULL == mii_info) { - if (netif_msg_ifup(priv)) - printk(KERN_ERR "%s: Could not allocate mii_info\n", - dev->name); - return -ENOMEM; - } - - mii_info->speed = SPEED_1000; - mii_info->duplex = DUPLEX_FULL; - mii_info->pause = 0; - mii_info->link = 1; - - mii_info->advertising = (ADVERTISED_10baseT_Half | - ADVERTISED_10baseT_Full | - ADVERTISED_100baseT_Half | - ADVERTISED_100baseT_Full | - ADVERTISED_1000baseT_Full); - mii_info->autoneg = 1; + phydev = phy_connect(dev, priv->einfo->bus_id, &adjust_link, 0); - spin_lock_init(&mii_info->mdio_lock); - - mii_info->mii_id = priv->einfo->phyid; - - mii_info->dev = dev; - - mii_info->mdio_read = &read_phy_reg; - mii_info->mdio_write = &write_phy_reg; - - priv->mii_info = mii_info; - - /* Reset the management interface */ - gfar_write(&phyregs->miimcfg, MIIMCFG_RESET); - - /* Setup the MII Mgmt clock speed */ - gfar_write(&phyregs->miimcfg, MIIMCFG_INIT_VALUE); - - /* Wait until the bus is free */ - while ((gfar_read(&phyregs->miimind) & MIIMIND_BUSY) && - timeout--) - cpu_relax(); - - if(timeout <= 0) { - printk(KERN_ERR "%s: The MII Bus is stuck!\n", - dev->name); - err = -1; - goto bus_fail; - } - - /* get info for this PHY */ - curphy = get_phy_info(priv->mii_info); - - if (curphy == NULL) { - if (netif_msg_ifup(priv)) - printk(KERN_ERR "%s: No PHY found\n", dev->name); - err = -1; - goto no_phy; + if (IS_ERR(phydev)) { + printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); + return PTR_ERR(phydev); } - mii_info->phyinfo = curphy; + /* Remove any features not supported by the controller */ + phydev->supported &= (GFAR_SUPPORTED | gigabit_support); + phydev->advertising = phydev->supported; - /* Run the commands which initialize the PHY */ - if(curphy->init) { - err = curphy->init(priv->mii_info); - - if (err) - goto phy_init_fail; - } + priv->phydev = phydev; return 0; - -phy_init_fail: -no_phy: -bus_fail: - kfree(mii_info); - - return err; } static void init_registers(struct net_device *dev) @@ -603,24 +520,13 @@ void stop_gfar(struct net_device *dev) struct gfar *regs = priv->regs; unsigned long flags; + phy_stop(priv->phydev); + /* Lock it down */ spin_lock_irqsave(&priv->lock, flags); - /* Tell the kernel the link is down */ - priv->mii_info->link = 0; - adjust_link(dev); - gfar_halt(dev); - if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { - /* Clear any pending interrupts */ - mii_clear_phy_interrupt(priv->mii_info); - - /* Disable PHY Interrupts */ - mii_configure_phy_interrupt(priv->mii_info, - MII_INTERRUPT_DISABLED); - } - spin_unlock_irqrestore(&priv->lock, flags); /* Free the IRQs */ @@ -629,13 +535,7 @@ void stop_gfar(struct net_device *dev) free_irq(priv->interruptTransmit, dev); free_irq(priv->interruptReceive, dev); } else { - free_irq(priv->interruptTransmit, dev); - } - - if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { - free_irq(priv->einfo->interruptPHY, dev); - } else { - del_timer_sync(&priv->phy_info_timer); + free_irq(priv->interruptTransmit, dev); } free_skb_resources(priv); @@ -649,7 +549,7 @@ void stop_gfar(struct net_device *dev) /* If there are any tx skbs or rx skbs still around, free them. * Then free tx_skbuff and rx_skbuff */ -void free_skb_resources(struct gfar_private *priv) +static void free_skb_resources(struct gfar_private *priv) { struct rxbd8 *rxbdp; struct txbd8 *txbdp; @@ -770,7 +670,7 @@ int startup_gfar(struct net_device *dev) (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * priv->tx_ring_size, GFP_KERNEL); - if (priv->tx_skbuff == NULL) { + if (NULL == priv->tx_skbuff) { if (netif_msg_ifup(priv)) printk(KERN_ERR "%s: Could not allocate tx_skbuff\n", dev->name); @@ -785,7 +685,7 @@ int startup_gfar(struct net_device *dev) (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * priv->rx_ring_size, GFP_KERNEL); - if (priv->rx_skbuff == NULL) { + if (NULL == priv->rx_skbuff) { if (netif_msg_ifup(priv)) printk(KERN_ERR "%s: Could not allocate rx_skbuff\n", dev->name); @@ -879,13 +779,7 @@ int startup_gfar(struct net_device *dev) } } - /* Set up the PHY change work queue */ - INIT_WORK(&priv->tq, gfar_phy_change, dev); - - init_timer(&priv->phy_info_timer); - priv->phy_info_timer.function = &gfar_phy_startup_timer; - priv->phy_info_timer.data = (unsigned long) priv->mii_info; - mod_timer(&priv->phy_info_timer, jiffies + HZ); + phy_start(priv->phydev); /* Configure the coalescing support */ if (priv->txcoalescing) @@ -933,11 +827,6 @@ tx_skb_fail: priv->tx_bd_base, gfar_read(®s->tbase0)); - if (priv->mii_info->phyinfo->close) - priv->mii_info->phyinfo->close(priv->mii_info); - - kfree(priv->mii_info); - return err; } @@ -1035,7 +924,7 @@ static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev) txbdp->status &= TXBD_WRAP; /* Set up checksumming */ - if ((dev->features & NETIF_F_IP_CSUM) + if ((dev->features & NETIF_F_IP_CSUM) && (CHECKSUM_HW == skb->ip_summed)) { fcb = gfar_add_fcb(skb, txbdp); gfar_tx_checksum(skb, fcb); @@ -1103,11 +992,9 @@ static int gfar_close(struct net_device *dev) struct gfar_private *priv = netdev_priv(dev); stop_gfar(dev); - /* Shutdown the PHY */ - if (priv->mii_info->phyinfo->close) - priv->mii_info->phyinfo->close(priv->mii_info); - - kfree(priv->mii_info); + /* Disconnect from the PHY */ + phy_disconnect(priv->phydev); + priv->phydev = NULL; netif_stop_queue(dev); @@ -1343,7 +1230,7 @@ struct sk_buff * gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp) while ((!skb) && timeout--) skb = dev_alloc_skb(priv->rx_buffer_size + RXBUF_ALIGNMENT); - if (skb == NULL) + if (NULL == skb) return NULL; /* We need the data buffer to be aligned properly. We will reserve @@ -1490,7 +1377,7 @@ static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, struct gfar_private *priv = netdev_priv(dev); struct rxfcb *fcb = NULL; - if (skb == NULL) { + if (NULL == skb) { if (netif_msg_rx_err(priv)) printk(KERN_WARNING "%s: Missing skb!!.\n", dev->name); priv->stats.rx_dropped++; @@ -1718,131 +1605,9 @@ static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs) return IRQ_HANDLED; } -static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs) -{ - struct net_device *dev = (struct net_device *) dev_id; - struct gfar_private *priv = netdev_priv(dev); - - /* Clear the interrupt */ - mii_clear_phy_interrupt(priv->mii_info); - - /* Disable PHY interrupts */ - mii_configure_phy_interrupt(priv->mii_info, - MII_INTERRUPT_DISABLED); - - /* Schedule the phy change */ - schedule_work(&priv->tq); - - return IRQ_HANDLED; -} - -/* Scheduled by the phy_interrupt/timer to handle PHY changes */ -static void gfar_phy_change(void *data) -{ - struct net_device *dev = (struct net_device *) data; - struct gfar_private *priv = netdev_priv(dev); - int result = 0; - - /* Delay to give the PHY a chance to change the - * register state */ - msleep(1); - - /* Update the link, speed, duplex */ - result = priv->mii_info->phyinfo->read_status(priv->mii_info); - - /* Adjust the known status as long as the link - * isn't still coming up */ - if((0 == result) || (priv->mii_info->link == 0)) - adjust_link(dev); - - /* Reenable interrupts, if needed */ - if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) - mii_configure_phy_interrupt(priv->mii_info, - MII_INTERRUPT_ENABLED); -} - -/* Called every so often on systems that don't interrupt - * the core for PHY changes */ -static void gfar_phy_timer(unsigned long data) -{ - struct net_device *dev = (struct net_device *) data; - struct gfar_private *priv = netdev_priv(dev); - - schedule_work(&priv->tq); - - mod_timer(&priv->phy_info_timer, jiffies + - GFAR_PHY_CHANGE_TIME * HZ); -} - -/* Keep trying aneg for some time - * If, after GFAR_AN_TIMEOUT seconds, it has not - * finished, we switch to forced. - * Either way, once the process has completed, we either - * request the interrupt, or switch the timer over to - * using gfar_phy_timer to check status */ -static void gfar_phy_startup_timer(unsigned long data) -{ - int result; - static int secondary = GFAR_AN_TIMEOUT; - struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data; - struct gfar_private *priv = netdev_priv(mii_info->dev); - - /* Configure the Auto-negotiation */ - result = mii_info->phyinfo->config_aneg(mii_info); - - /* If autonegotiation failed to start, and - * we haven't timed out, reset the timer, and return */ - if (result && secondary--) { - mod_timer(&priv->phy_info_timer, jiffies + HZ); - return; - } else if (result) { - /* Couldn't start autonegotiation. - * Try switching to forced */ - mii_info->autoneg = 0; - result = mii_info->phyinfo->config_aneg(mii_info); - - /* Forcing failed! Give up */ - if(result) { - if (netif_msg_link(priv)) - printk(KERN_ERR "%s: Forcing failed!\n", - mii_info->dev->name); - return; - } - } - - /* Kill the timer so it can be restarted */ - del_timer_sync(&priv->phy_info_timer); - - /* Grab the PHY interrupt, if necessary/possible */ - if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { - if (request_irq(priv->einfo->interruptPHY, - phy_interrupt, - SA_SHIRQ, - "phy_interrupt", - mii_info->dev) < 0) { - if (netif_msg_intr(priv)) - printk(KERN_ERR "%s: Can't get IRQ %d (PHY)\n", - mii_info->dev->name, - priv->einfo->interruptPHY); - } else { - mii_configure_phy_interrupt(priv->mii_info, - MII_INTERRUPT_ENABLED); - return; - } - } - - /* Start the timer again, this time in order to - * handle a change in status */ - init_timer(&priv->phy_info_timer); - priv->phy_info_timer.function = &gfar_phy_timer; - priv->phy_info_timer.data = (unsigned long) mii_info->dev; - mod_timer(&priv->phy_info_timer, jiffies + - GFAR_PHY_CHANGE_TIME * HZ); -} - /* Called every time the controller might need to be made * aware of new link state. The PHY code conveys this - * information through variables in the priv structure, and this + * information through variables in the phydev structure, and this * function converts those variables into the appropriate * register values, and can bring down the device if needed. */ @@ -1850,84 +1615,68 @@ static void adjust_link(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); struct gfar *regs = priv->regs; - u32 tempval; - struct gfar_mii_info *mii_info = priv->mii_info; + unsigned long flags; + struct phy_device *phydev = priv->phydev; + int new_state = 0; + + spin_lock_irqsave(&priv->lock, flags); + if (phydev->link) { + u32 tempval = gfar_read(®s->maccfg2); - if (mii_info->link) { /* Now we make sure that we can be in full duplex mode. * If not, we operate in half-duplex mode. */ - if (mii_info->duplex != priv->oldduplex) { - if (!(mii_info->duplex)) { - tempval = gfar_read(®s->maccfg2); + if (phydev->duplex != priv->oldduplex) { + new_state = 1; + if (!(phydev->duplex)) tempval &= ~(MACCFG2_FULL_DUPLEX); - gfar_write(®s->maccfg2, tempval); - - if (netif_msg_link(priv)) - printk(KERN_INFO "%s: Half Duplex\n", - dev->name); - } else { - tempval = gfar_read(®s->maccfg2); + else tempval |= MACCFG2_FULL_DUPLEX; - gfar_write(®s->maccfg2, tempval); - if (netif_msg_link(priv)) - printk(KERN_INFO "%s: Full Duplex\n", - dev->name); - } - - priv->oldduplex = mii_info->duplex; + priv->oldduplex = phydev->duplex; } - if (mii_info->speed != priv->oldspeed) { - switch (mii_info->speed) { + if (phydev->speed != priv->oldspeed) { + new_state = 1; + switch (phydev->speed) { case 1000: - tempval = gfar_read(®s->maccfg2); tempval = ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII); - gfar_write(®s->maccfg2, tempval); break; case 100: case 10: - tempval = gfar_read(®s->maccfg2); tempval = ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII); - gfar_write(®s->maccfg2, tempval); break; default: if (netif_msg_link(priv)) printk(KERN_WARNING - "%s: Ack! Speed (%d) is not 10/100/1000!\n", - dev->name, mii_info->speed); + "%s: Ack! Speed (%d) is not 10/100/1000!\n", + dev->name, phydev->speed); break; } - if (netif_msg_link(priv)) - printk(KERN_INFO "%s: Speed %dBT\n", dev->name, - mii_info->speed); - - priv->oldspeed = mii_info->speed; + priv->oldspeed = phydev->speed; } + gfar_write(®s->maccfg2, tempval); + if (!priv->oldlink) { - if (netif_msg_link(priv)) - printk(KERN_INFO "%s: Link is up\n", dev->name); + new_state = 1; priv->oldlink = 1; - netif_carrier_on(dev); netif_schedule(dev); } - } else { - if (priv->oldlink) { - if (netif_msg_link(priv)) - printk(KERN_INFO "%s: Link is down\n", - dev->name); - priv->oldlink = 0; - priv->oldspeed = 0; - priv->oldduplex = -1; - netif_carrier_off(dev); - } + } else if (priv->oldlink) { + new_state = 1; + priv->oldlink = 0; + priv->oldspeed = 0; + priv->oldduplex = -1; } -} + if (new_state && netif_msg_link(priv)) + phy_print_status(phydev); + + spin_unlock_irqrestore(&priv->lock, flags); +} /* Update the hash table based on the current list of multicast * addresses we subscribe to. Also, change the promiscuity of @@ -2122,12 +1871,23 @@ static struct device_driver gfar_driver = { static int __init gfar_init(void) { - return driver_register(&gfar_driver); + int err = gfar_mdio_init(); + + if (err) + return err; + + err = driver_register(&gfar_driver); + + if (err) + gfar_mdio_exit(); + + return err; } static void __exit gfar_exit(void) { driver_unregister(&gfar_driver); + gfar_mdio_exit(); } module_init(gfar_init); diff --git a/drivers/net/gianfar.h b/drivers/net/gianfar.h index 28af087d9fbb..c77ca6c0d04a 100644 --- a/drivers/net/gianfar.h +++ b/drivers/net/gianfar.h @@ -17,7 +17,6 @@ * * Still left to do: * -Add support for module parameters - * -Add support for ethtool -s * -Add patch for ethtool phys id */ #ifndef __GIANFAR_H @@ -37,7 +36,8 @@ #include #include #include -#include +#include +#include #include #include @@ -48,7 +48,8 @@ #include #include #include -#include "gianfar_phy.h" +#include +#include "gianfar_mii.h" /* The maximum number of packets to be handled in one call of gfar_poll */ #define GFAR_DEV_WEIGHT 64 @@ -73,7 +74,7 @@ #define PHY_INIT_TIMEOUT 100000 #define GFAR_PHY_CHANGE_TIME 2 -#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.1, " +#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.2, " #define DRV_NAME "gfar-enet" extern const char gfar_driver_name[]; extern const char gfar_driver_version[]; @@ -578,12 +579,7 @@ struct gfar { u32 hafdup; /* 0x.50c - Half Duplex Register */ u32 maxfrm; /* 0x.510 - Maximum Frame Length Register */ u8 res18[12]; - u32 miimcfg; /* 0x.520 - MII Management Configuration Register */ - u32 miimcom; /* 0x.524 - MII Management Command Register */ - u32 miimadd; /* 0x.528 - MII Management Address Register */ - u32 miimcon; /* 0x.52c - MII Management Control Register */ - u32 miimstat; /* 0x.530 - MII Management Status Register */ - u32 miimind; /* 0x.534 - MII Management Indicator Register */ + u8 gfar_mii_regs[24]; /* See gianfar_phy.h */ u8 res19[4]; u32 ifstat; /* 0x.53c - Interface Status Register */ u32 macstnaddr1; /* 0x.540 - Station Address Part 1 Register */ @@ -688,9 +684,6 @@ struct gfar_private { struct gfar *regs; /* Pointer to the GFAR memory mapped Registers */ u32 *hash_regs[16]; int hash_width; - struct gfar *phyregs; - struct work_struct tq; - struct timer_list phy_info_timer; struct net_device_stats stats; /* linux network statistics */ struct gfar_extra_stats extra_stats; spinlock_t lock; @@ -710,7 +703,8 @@ struct gfar_private { unsigned int interruptError; struct gianfar_platform_data *einfo; - struct gfar_mii_info *mii_info; + struct phy_device *phydev; + struct mii_bus *mii_bus; int oldspeed; int oldduplex; int oldlink; @@ -732,4 +726,12 @@ extern inline void gfar_write(volatile unsigned *addr, u32 val) extern struct ethtool_ops *gfar_op_array[]; +extern irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs); +extern int startup_gfar(struct net_device *dev); +extern void stop_gfar(struct net_device *dev); +extern void gfar_halt(struct net_device *dev); +extern void gfar_phy_test(struct mii_bus *bus, struct phy_device *phydev, + int enable, u32 regnum, u32 read); +void gfar_setup_stashing(struct net_device *dev); + #endif /* __GIANFAR_H */ diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c index a451de629197..68e3578e7613 100644 --- a/drivers/net/gianfar_ethtool.c +++ b/drivers/net/gianfar_ethtool.c @@ -39,17 +39,18 @@ #include #include #include +#include +#include #include "gianfar.h" #define is_power_of_2(x) ((x) != 0 && (((x) & ((x) - 1)) == 0)) -extern int startup_gfar(struct net_device *dev); -extern void stop_gfar(struct net_device *dev); -extern void gfar_halt(struct net_device *dev); extern void gfar_start(struct net_device *dev); extern int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit); +#define GFAR_MAX_COAL_USECS 0xffff +#define GFAR_MAX_COAL_FRAMES 0xff static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy, u64 * buf); static void gfar_gstrings(struct net_device *dev, u32 stringset, u8 * buf); @@ -182,38 +183,32 @@ static void gfar_gdrvinfo(struct net_device *dev, struct drvinfo->eedump_len = 0; } + +static int gfar_ssettings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct gfar_private *priv = netdev_priv(dev); + struct phy_device *phydev = priv->phydev; + + if (NULL == phydev) + return -ENODEV; + + return phy_ethtool_sset(phydev, cmd); +} + + /* Return the current settings in the ethtool_cmd structure */ static int gfar_gsettings(struct net_device *dev, struct ethtool_cmd *cmd) { struct gfar_private *priv = netdev_priv(dev); - uint gigabit_support = - priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ? - SUPPORTED_1000baseT_Full : 0; - uint gigabit_advert = - priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ? - ADVERTISED_1000baseT_Full: 0; - - cmd->supported = (SUPPORTED_10baseT_Half - | SUPPORTED_100baseT_Half - | SUPPORTED_100baseT_Full - | gigabit_support | SUPPORTED_Autoneg); - - /* For now, we always advertise everything */ - cmd->advertising = (ADVERTISED_10baseT_Half - | ADVERTISED_100baseT_Half - | ADVERTISED_100baseT_Full - | gigabit_advert | ADVERTISED_Autoneg); - - cmd->speed = priv->mii_info->speed; - cmd->duplex = priv->mii_info->duplex; - cmd->port = PORT_MII; - cmd->phy_address = priv->mii_info->mii_id; - cmd->transceiver = XCVR_EXTERNAL; - cmd->autoneg = AUTONEG_ENABLE; + struct phy_device *phydev = priv->phydev; + + if (NULL == phydev) + return -ENODEV; + cmd->maxtxpkt = priv->txcount; cmd->maxrxpkt = priv->rxcount; - return 0; + return phy_ethtool_gset(phydev, cmd); } /* Return the length of the register structure */ @@ -241,14 +236,14 @@ static unsigned int gfar_usecs2ticks(struct gfar_private *priv, unsigned int use unsigned int count; /* The timer is different, depending on the interface speed */ - switch (priv->mii_info->speed) { - case 1000: + switch (priv->phydev->speed) { + case SPEED_1000: count = GFAR_GBIT_TIME; break; - case 100: + case SPEED_100: count = GFAR_100_TIME; break; - case 10: + case SPEED_10: default: count = GFAR_10_TIME; break; @@ -265,14 +260,14 @@ static unsigned int gfar_ticks2usecs(struct gfar_private *priv, unsigned int tic unsigned int count; /* The timer is different, depending on the interface speed */ - switch (priv->mii_info->speed) { - case 1000: + switch (priv->phydev->speed) { + case SPEED_1000: count = GFAR_GBIT_TIME; break; - case 100: + case SPEED_100: count = GFAR_100_TIME; break; - case 10: + case SPEED_10: default: count = GFAR_10_TIME; break; @@ -292,6 +287,9 @@ static int gfar_gcoalesce(struct net_device *dev, struct ethtool_coalesce *cvals if (!(priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE)) return -EOPNOTSUPP; + if (NULL == priv->phydev) + return -ENODEV; + cvals->rx_coalesce_usecs = gfar_ticks2usecs(priv, priv->rxtime); cvals->rx_max_coalesced_frames = priv->rxcount; @@ -348,6 +346,22 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals else priv->rxcoalescing = 1; + if (NULL == priv->phydev) + return -ENODEV; + + /* Check the bounds of the values */ + if (cvals->rx_coalesce_usecs > GFAR_MAX_COAL_USECS) { + pr_info("Coalescing is limited to %d microseconds\n", + GFAR_MAX_COAL_USECS); + return -EINVAL; + } + + if (cvals->rx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) { + pr_info("Coalescing is limited to %d frames\n", + GFAR_MAX_COAL_FRAMES); + return -EINVAL; + } + priv->rxtime = gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs); priv->rxcount = cvals->rx_max_coalesced_frames; @@ -358,6 +372,19 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals else priv->txcoalescing = 1; + /* Check the bounds of the values */ + if (cvals->tx_coalesce_usecs > GFAR_MAX_COAL_USECS) { + pr_info("Coalescing is limited to %d microseconds\n", + GFAR_MAX_COAL_USECS); + return -EINVAL; + } + + if (cvals->tx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) { + pr_info("Coalescing is limited to %d frames\n", + GFAR_MAX_COAL_FRAMES); + return -EINVAL; + } + priv->txtime = gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs); priv->txcount = cvals->tx_max_coalesced_frames; @@ -536,6 +563,7 @@ static void gfar_set_msglevel(struct net_device *dev, uint32_t data) struct ethtool_ops gfar_ethtool_ops = { .get_settings = gfar_gsettings, + .set_settings = gfar_ssettings, .get_drvinfo = gfar_gdrvinfo, .get_regs_len = gfar_reglen, .get_regs = gfar_get_regs, diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c new file mode 100644 index 000000000000..1eca1dbca7f1 --- /dev/null +++ b/drivers/net/gianfar_mii.c @@ -0,0 +1,219 @@ +/* + * drivers/net/gianfar_mii.c + * + * Gianfar Ethernet Driver -- MIIM bus implementation + * Provides Bus interface for MIIM regs + * + * Author: Andy Fleming + * Maintainer: Kumar Gala (kumar.gala@freescale.com) + * + * Copyright (c) 2002-2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include "gianfar.h" +#include "gianfar_mii.h" + +/* Write value to the PHY at mii_id at register regnum, + * on the bus, waiting until the write is done before returning. + * All PHY configuration is done through the TSEC1 MIIM regs */ +int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) +{ + struct gfar_mii *regs = bus->priv; + + /* Set the PHY address and the register address we want to write */ + gfar_write(®s->miimadd, (mii_id << 8) | regnum); + + /* Write out the value we want */ + gfar_write(®s->miimcon, value); + + /* Wait for the transaction to finish */ + while (gfar_read(®s->miimind) & MIIMIND_BUSY) + cpu_relax(); + + return 0; +} + +/* Read the bus for PHY at addr mii_id, register regnum, and + * return the value. Clears miimcom first. All PHY + * configuration has to be done through the TSEC1 MIIM regs */ +int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) +{ + struct gfar_mii *regs = bus->priv; + u16 value; + + /* Set the PHY address and the register address we want to read */ + gfar_write(®s->miimadd, (mii_id << 8) | regnum); + + /* Clear miimcom, and then initiate a read */ + gfar_write(®s->miimcom, 0); + gfar_write(®s->miimcom, MII_READ_COMMAND); + + /* Wait for the transaction to finish */ + while (gfar_read(®s->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY)) + cpu_relax(); + + /* Grab the value of the register from miimstat */ + value = gfar_read(®s->miimstat); + + return value; +} + + +/* Reset the MIIM registers, and wait for the bus to free */ +int gfar_mdio_reset(struct mii_bus *bus) +{ + struct gfar_mii *regs = bus->priv; + unsigned int timeout = PHY_INIT_TIMEOUT; + + spin_lock_bh(&bus->mdio_lock); + + /* Reset the management interface */ + gfar_write(®s->miimcfg, MIIMCFG_RESET); + + /* Setup the MII Mgmt clock speed */ + gfar_write(®s->miimcfg, MIIMCFG_INIT_VALUE); + + /* Wait until the bus is free */ + while ((gfar_read(®s->miimind) & MIIMIND_BUSY) && + timeout--) + cpu_relax(); + + spin_unlock_bh(&bus->mdio_lock); + + if(timeout <= 0) { + printk(KERN_ERR "%s: The MII Bus is stuck!\n", + bus->name); + return -EBUSY; + } + + return 0; +} + + +int gfar_mdio_probe(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct gianfar_mdio_data *pdata; + struct gfar_mii *regs; + struct mii_bus *new_bus; + int err = 0; + + if (NULL == dev) + return -EINVAL; + + new_bus = kmalloc(sizeof(struct mii_bus), GFP_KERNEL); + + if (NULL == new_bus) + return -ENOMEM; + + new_bus->name = "Gianfar MII Bus", + new_bus->read = &gfar_mdio_read, + new_bus->write = &gfar_mdio_write, + new_bus->reset = &gfar_mdio_reset, + new_bus->id = pdev->id; + + pdata = (struct gianfar_mdio_data *)pdev->dev.platform_data; + + if (NULL == pdata) { + printk(KERN_ERR "gfar mdio %d: Missing platform data!\n", pdev->id); + return -ENODEV; + } + + /* Set the PHY base address */ + regs = (struct gfar_mii *) ioremap(pdata->paddr, + sizeof (struct gfar_mii)); + + if (NULL == regs) { + err = -ENOMEM; + goto reg_map_fail; + } + + new_bus->priv = regs; + + new_bus->irq = pdata->irq; + + new_bus->dev = dev; + dev_set_drvdata(dev, new_bus); + + err = mdiobus_register(new_bus); + + if (0 != err) { + printk (KERN_ERR "%s: Cannot register as MDIO bus\n", + new_bus->name); + goto bus_register_fail; + } + + return 0; + +bus_register_fail: + iounmap((void *) regs); +reg_map_fail: + kfree(new_bus); + + return err; +} + + +int gfar_mdio_remove(struct device *dev) +{ + struct mii_bus *bus = dev_get_drvdata(dev); + + mdiobus_unregister(bus); + + dev_set_drvdata(dev, NULL); + + iounmap((void *) (&bus->priv)); + bus->priv = NULL; + kfree(bus); + + return 0; +} + +static struct device_driver gianfar_mdio_driver = { + .name = "fsl-gianfar_mdio", + .bus = &platform_bus_type, + .probe = gfar_mdio_probe, + .remove = gfar_mdio_remove, +}; + +int __init gfar_mdio_init(void) +{ + return driver_register(&gianfar_mdio_driver); +} + +void __exit gfar_mdio_exit(void) +{ + driver_unregister(&gianfar_mdio_driver); +} diff --git a/drivers/net/gianfar_mii.h b/drivers/net/gianfar_mii.h new file mode 100644 index 000000000000..56e5665d5c9b --- /dev/null +++ b/drivers/net/gianfar_mii.h @@ -0,0 +1,45 @@ +/* + * drivers/net/gianfar_mii.h + * + * Gianfar Ethernet Driver -- MII Management Bus Implementation + * Driver for the MDIO bus controller in the Gianfar register space + * + * Author: Andy Fleming + * Maintainer: Kumar Gala (kumar.gala@freescale.com) + * + * Copyright (c) 2002-2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#ifndef __GIANFAR_MII_H +#define __GIANFAR_MII_H + +#define MIIMIND_BUSY 0x00000001 +#define MIIMIND_NOTVALID 0x00000004 + +#define MII_READ_COMMAND 0x00000001 + +#define GFAR_SUPPORTED (SUPPORTED_10baseT_Half \ + | SUPPORTED_100baseT_Half \ + | SUPPORTED_100baseT_Full \ + | SUPPORTED_Autoneg \ + | SUPPORTED_MII) + +struct gfar_mii { + u32 miimcfg; /* 0x.520 - MII Management Config Register */ + u32 miimcom; /* 0x.524 - MII Management Command Register */ + u32 miimadd; /* 0x.528 - MII Management Address Register */ + u32 miimcon; /* 0x.52c - MII Management Control Register */ + u32 miimstat; /* 0x.530 - MII Management Status Register */ + u32 miimind; /* 0x.534 - MII Management Indicator Register */ +}; + +int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum); +int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value); +int __init gfar_mdio_init(void); +void __exit gfar_mdio_exit(void); +#endif /* GIANFAR_PHY_H */ diff --git a/drivers/net/gianfar_phy.c b/drivers/net/gianfar_phy.c deleted file mode 100644 index 7c965f268a82..000000000000 --- a/drivers/net/gianfar_phy.c +++ /dev/null @@ -1,661 +0,0 @@ -/* - * drivers/net/gianfar_phy.c - * - * Gianfar Ethernet Driver -- PHY handling - * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560 - * Based on 8260_io/fcc_enet.c - * - * Author: Andy Fleming - * Maintainer: Kumar Gala (kumar.gala@freescale.com) - * - * Copyright (c) 2002-2004 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -#include "gianfar.h" -#include "gianfar_phy.h" - -static void config_genmii_advert(struct gfar_mii_info *mii_info); -static void genmii_setup_forced(struct gfar_mii_info *mii_info); -static void genmii_restart_aneg(struct gfar_mii_info *mii_info); -static int gbit_config_aneg(struct gfar_mii_info *mii_info); -static int genmii_config_aneg(struct gfar_mii_info *mii_info); -static int genmii_update_link(struct gfar_mii_info *mii_info); -static int genmii_read_status(struct gfar_mii_info *mii_info); -u16 phy_read(struct gfar_mii_info *mii_info, u16 regnum); -void phy_write(struct gfar_mii_info *mii_info, u16 regnum, u16 val); - -/* Write value to the PHY for this device to the register at regnum, */ -/* waiting until the write is done before it returns. All PHY */ -/* configuration has to be done through the TSEC1 MIIM regs */ -void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value) -{ - struct gfar_private *priv = netdev_priv(dev); - struct gfar *regbase = priv->phyregs; - - /* Set the PHY address and the register address we want to write */ - gfar_write(®base->miimadd, (mii_id << 8) | regnum); - - /* Write out the value we want */ - gfar_write(®base->miimcon, value); - - /* Wait for the transaction to finish */ - while (gfar_read(®base->miimind) & MIIMIND_BUSY) - cpu_relax(); -} - -/* Reads from register regnum in the PHY for device dev, */ -/* returning the value. Clears miimcom first. All PHY */ -/* configuration has to be done through the TSEC1 MIIM regs */ -int read_phy_reg(struct net_device *dev, int mii_id, int regnum) -{ - struct gfar_private *priv = netdev_priv(dev); - struct gfar *regbase = priv->phyregs; - u16 value; - - /* Set the PHY address and the register address we want to read */ - gfar_write(®base->miimadd, (mii_id << 8) | regnum); - - /* Clear miimcom, and then initiate a read */ - gfar_write(®base->miimcom, 0); - gfar_write(®base->miimcom, MII_READ_COMMAND); - - /* Wait for the transaction to finish */ - while (gfar_read(®base->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY)) - cpu_relax(); - - /* Grab the value of the register from miimstat */ - value = gfar_read(®base->miimstat); - - return value; -} - -void mii_clear_phy_interrupt(struct gfar_mii_info *mii_info) -{ - if(mii_info->phyinfo->ack_interrupt) - mii_info->phyinfo->ack_interrupt(mii_info); -} - - -void mii_configure_phy_interrupt(struct gfar_mii_info *mii_info, u32 interrupts) -{ - mii_info->interrupts = interrupts; - if(mii_info->phyinfo->config_intr) - mii_info->phyinfo->config_intr(mii_info); -} - - -/* Writes MII_ADVERTISE with the appropriate values, after - * sanitizing advertise to make sure only supported features - * are advertised - */ -static void config_genmii_advert(struct gfar_mii_info *mii_info) -{ - u32 advertise; - u16 adv; - - /* Only allow advertising what this PHY supports */ - mii_info->advertising &= mii_info->phyinfo->features; - advertise = mii_info->advertising; - - /* Setup standard advertisement */ - adv = phy_read(mii_info, MII_ADVERTISE); - adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4); - if (advertise & ADVERTISED_10baseT_Half) - adv |= ADVERTISE_10HALF; - if (advertise & ADVERTISED_10baseT_Full) - adv |= ADVERTISE_10FULL; - if (advertise & ADVERTISED_100baseT_Half) - adv |= ADVERTISE_100HALF; - if (advertise & ADVERTISED_100baseT_Full) - adv |= ADVERTISE_100FULL; - phy_write(mii_info, MII_ADVERTISE, adv); -} - -static void genmii_setup_forced(struct gfar_mii_info *mii_info) -{ - u16 ctrl; - u32 features = mii_info->phyinfo->features; - - ctrl = phy_read(mii_info, MII_BMCR); - - ctrl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPEED1000|BMCR_ANENABLE); - ctrl |= BMCR_RESET; - - switch(mii_info->speed) { - case SPEED_1000: - if(features & (SUPPORTED_1000baseT_Half - | SUPPORTED_1000baseT_Full)) { - ctrl |= BMCR_SPEED1000; - break; - } - mii_info->speed = SPEED_100; - case SPEED_100: - if (features & (SUPPORTED_100baseT_Half - | SUPPORTED_100baseT_Full)) { - ctrl |= BMCR_SPEED100; - break; - } - mii_info->speed = SPEED_10; - case SPEED_10: - if (features & (SUPPORTED_10baseT_Half - | SUPPORTED_10baseT_Full)) - break; - default: /* Unsupported speed! */ - printk(KERN_ERR "%s: Bad speed!\n", - mii_info->dev->name); - break; - } - - phy_write(mii_info, MII_BMCR, ctrl); -} - - -/* Enable and Restart Autonegotiation */ -static void genmii_restart_aneg(struct gfar_mii_info *mii_info) -{ - u16 ctl; - - ctl = phy_read(mii_info, MII_BMCR); - ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); - phy_write(mii_info, MII_BMCR, ctl); -} - - -static int gbit_config_aneg(struct gfar_mii_info *mii_info) -{ - u16 adv; - u32 advertise; - - if(mii_info->autoneg) { - /* Configure the ADVERTISE register */ - config_genmii_advert(mii_info); - advertise = mii_info->advertising; - - adv = phy_read(mii_info, MII_1000BASETCONTROL); - adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP | - MII_1000BASETCONTROL_HALFDUPLEXCAP); - if (advertise & SUPPORTED_1000baseT_Half) - adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP; - if (advertise & SUPPORTED_1000baseT_Full) - adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP; - phy_write(mii_info, MII_1000BASETCONTROL, adv); - - /* Start/Restart aneg */ - genmii_restart_aneg(mii_info); - } else - genmii_setup_forced(mii_info); - - return 0; -} - -static int marvell_config_aneg(struct gfar_mii_info *mii_info) -{ - /* The Marvell PHY has an errata which requires - * that certain registers get written in order - * to restart autonegotiation */ - phy_write(mii_info, MII_BMCR, BMCR_RESET); - - phy_write(mii_info, 0x1d, 0x1f); - phy_write(mii_info, 0x1e, 0x200c); - phy_write(mii_info, 0x1d, 0x5); - phy_write(mii_info, 0x1e, 0); - phy_write(mii_info, 0x1e, 0x100); - - gbit_config_aneg(mii_info); - - return 0; -} -static int genmii_config_aneg(struct gfar_mii_info *mii_info) -{ - if (mii_info->autoneg) { - config_genmii_advert(mii_info); - genmii_restart_aneg(mii_info); - } else - genmii_setup_forced(mii_info); - - return 0; -} - - -static int genmii_update_link(struct gfar_mii_info *mii_info) -{ - u16 status; - - /* Do a fake read */ - phy_read(mii_info, MII_BMSR); - - /* Read link and autonegotiation status */ - status = phy_read(mii_info, MII_BMSR); - if ((status & BMSR_LSTATUS) == 0) - mii_info->link = 0; - else - mii_info->link = 1; - - /* If we are autonegotiating, and not done, - * return an error */ - if (mii_info->autoneg && !(status & BMSR_ANEGCOMPLETE)) - return -EAGAIN; - - return 0; -} - -static int genmii_read_status(struct gfar_mii_info *mii_info) -{ - u16 status; - int err; - - /* Update the link, but return if there - * was an error */ - err = genmii_update_link(mii_info); - if (err) - return err; - - if (mii_info->autoneg) { - status = phy_read(mii_info, MII_LPA); - - if (status & (LPA_10FULL | LPA_100FULL)) - mii_info->duplex = DUPLEX_FULL; - else - mii_info->duplex = DUPLEX_HALF; - if (status & (LPA_100FULL | LPA_100HALF)) - mii_info->speed = SPEED_100; - else - mii_info->speed = SPEED_10; - mii_info->pause = 0; - } - /* On non-aneg, we assume what we put in BMCR is the speed, - * though magic-aneg shouldn't prevent this case from occurring - */ - - return 0; -} -static int marvell_read_status(struct gfar_mii_info *mii_info) -{ - u16 status; - int err; - - /* Update the link, but return if there - * was an error */ - err = genmii_update_link(mii_info); - if (err) - return err; - - /* If the link is up, read the speed and duplex */ - /* If we aren't autonegotiating, assume speeds - * are as set */ - if (mii_info->autoneg && mii_info->link) { - int speed; - status = phy_read(mii_info, MII_M1011_PHY_SPEC_STATUS); - -#if 0 - /* If speed and duplex aren't resolved, - * return an error. Isn't this handled - * by checking aneg? - */ - if ((status & MII_M1011_PHY_SPEC_STATUS_RESOLVED) == 0) - return -EAGAIN; -#endif - - /* Get the duplexity */ - if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX) - mii_info->duplex = DUPLEX_FULL; - else - mii_info->duplex = DUPLEX_HALF; - - /* Get the speed */ - speed = status & MII_M1011_PHY_SPEC_STATUS_SPD_MASK; - switch(speed) { - case MII_M1011_PHY_SPEC_STATUS_1000: - mii_info->speed = SPEED_1000; - break; - case MII_M1011_PHY_SPEC_STATUS_100: - mii_info->speed = SPEED_100; - break; - default: - mii_info->speed = SPEED_10; - break; - } - mii_info->pause = 0; - } - - return 0; -} - - -static int cis820x_read_status(struct gfar_mii_info *mii_info) -{ - u16 status; - int err; - - /* Update the link, but return if there - * was an error */ - err = genmii_update_link(mii_info); - if (err) - return err; - - /* If the link is up, read the speed and duplex */ - /* If we aren't autonegotiating, assume speeds - * are as set */ - if (mii_info->autoneg && mii_info->link) { - int speed; - - status = phy_read(mii_info, MII_CIS8201_AUX_CONSTAT); - if (status & MII_CIS8201_AUXCONSTAT_DUPLEX) - mii_info->duplex = DUPLEX_FULL; - else - mii_info->duplex = DUPLEX_HALF; - - speed = status & MII_CIS8201_AUXCONSTAT_SPEED; - - switch (speed) { - case MII_CIS8201_AUXCONSTAT_GBIT: - mii_info->speed = SPEED_1000; - break; - case MII_CIS8201_AUXCONSTAT_100: - mii_info->speed = SPEED_100; - break; - default: - mii_info->speed = SPEED_10; - break; - } - } - - return 0; -} - -static int marvell_ack_interrupt(struct gfar_mii_info *mii_info) -{ - /* Clear the interrupts by reading the reg */ - phy_read(mii_info, MII_M1011_IEVENT); - - return 0; -} - -static int marvell_config_intr(struct gfar_mii_info *mii_info) -{ - if(mii_info->interrupts == MII_INTERRUPT_ENABLED) - phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT); - else - phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR); - - return 0; -} - -static int cis820x_init(struct gfar_mii_info *mii_info) -{ - phy_write(mii_info, MII_CIS8201_AUX_CONSTAT, - MII_CIS8201_AUXCONSTAT_INIT); - phy_write(mii_info, MII_CIS8201_EXT_CON1, - MII_CIS8201_EXTCON1_INIT); - - return 0; -} - -static int cis820x_ack_interrupt(struct gfar_mii_info *mii_info) -{ - phy_read(mii_info, MII_CIS8201_ISTAT); - - return 0; -} - -static int cis820x_config_intr(struct gfar_mii_info *mii_info) -{ - if(mii_info->interrupts == MII_INTERRUPT_ENABLED) - phy_write(mii_info, MII_CIS8201_IMASK, MII_CIS8201_IMASK_MASK); - else - phy_write(mii_info, MII_CIS8201_IMASK, 0); - - return 0; -} - -#define DM9161_DELAY 10 - -static int dm9161_read_status(struct gfar_mii_info *mii_info) -{ - u16 status; - int err; - - /* Update the link, but return if there - * was an error */ - err = genmii_update_link(mii_info); - if (err) - return err; - - /* If the link is up, read the speed and duplex */ - /* If we aren't autonegotiating, assume speeds - * are as set */ - if (mii_info->autoneg && mii_info->link) { - status = phy_read(mii_info, MII_DM9161_SCSR); - if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_100H)) - mii_info->speed = SPEED_100; - else - mii_info->speed = SPEED_10; - - if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_10F)) - mii_info->duplex = DUPLEX_FULL; - else - mii_info->duplex = DUPLEX_HALF; - } - - return 0; -} - - -static int dm9161_config_aneg(struct gfar_mii_info *mii_info) -{ - struct dm9161_private *priv = mii_info->priv; - - if(0 == priv->resetdone) - return -EAGAIN; - - return 0; -} - -static void dm9161_timer(unsigned long data) -{ - struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data; - struct dm9161_private *priv = mii_info->priv; - u16 status = phy_read(mii_info, MII_BMSR); - - if (status & BMSR_ANEGCOMPLETE) { - priv->resetdone = 1; - } else - mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ); -} - -static int dm9161_init(struct gfar_mii_info *mii_info) -{ - struct dm9161_private *priv; - - /* Allocate the private data structure */ - priv = kmalloc(sizeof(struct dm9161_private), GFP_KERNEL); - - if (NULL == priv) - return -ENOMEM; - - mii_info->priv = priv; - - /* Reset is not done yet */ - priv->resetdone = 0; - - /* Isolate the PHY */ - phy_write(mii_info, MII_BMCR, BMCR_ISOLATE); - - /* Do not bypass the scrambler/descrambler */ - phy_write(mii_info, MII_DM9161_SCR, MII_DM9161_SCR_INIT); - - /* Clear 10BTCSR to default */ - phy_write(mii_info, MII_DM9161_10BTCSR, MII_DM9161_10BTCSR_INIT); - - /* Reconnect the PHY, and enable Autonegotiation */ - phy_write(mii_info, MII_BMCR, BMCR_ANENABLE); - - /* Start a timer for DM9161_DELAY seconds to wait - * for the PHY to be ready */ - init_timer(&priv->timer); - priv->timer.function = &dm9161_timer; - priv->timer.data = (unsigned long) mii_info; - mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ); - - return 0; -} - -static void dm9161_close(struct gfar_mii_info *mii_info) -{ - struct dm9161_private *priv = mii_info->priv; - - del_timer_sync(&priv->timer); - kfree(priv); -} - -#if 0 -static int dm9161_ack_interrupt(struct gfar_mii_info *mii_info) -{ - phy_read(mii_info, MII_DM9161_INTR); - - return 0; -} -#endif - -/* Cicada 820x */ -static struct phy_info phy_info_cis820x = { - 0x000fc440, - "Cicada Cis8204", - 0x000fffc0, - .features = MII_GBIT_FEATURES, - .init = &cis820x_init, - .config_aneg = &gbit_config_aneg, - .read_status = &cis820x_read_status, - .ack_interrupt = &cis820x_ack_interrupt, - .config_intr = &cis820x_config_intr, -}; - -static struct phy_info phy_info_dm9161 = { - .phy_id = 0x0181b880, - .name = "Davicom DM9161E", - .phy_id_mask = 0x0ffffff0, - .init = dm9161_init, - .config_aneg = dm9161_config_aneg, - .read_status = dm9161_read_status, - .close = dm9161_close, -}; - -static struct phy_info phy_info_marvell = { - .phy_id = 0x01410c00, - .phy_id_mask = 0xffffff00, - .name = "Marvell 88E1101/88E1111", - .features = MII_GBIT_FEATURES, - .config_aneg = &marvell_config_aneg, - .read_status = &marvell_read_status, - .ack_interrupt = &marvell_ack_interrupt, - .config_intr = &marvell_config_intr, -}; - -static struct phy_info phy_info_genmii= { - .phy_id = 0x00000000, - .phy_id_mask = 0x00000000, - .name = "Generic MII", - .features = MII_BASIC_FEATURES, - .config_aneg = genmii_config_aneg, - .read_status = genmii_read_status, -}; - -static struct phy_info *phy_info[] = { - &phy_info_cis820x, - &phy_info_marvell, - &phy_info_dm9161, - &phy_info_genmii, - NULL -}; - -u16 phy_read(struct gfar_mii_info *mii_info, u16 regnum) -{ - u16 retval; - unsigned long flags; - - spin_lock_irqsave(&mii_info->mdio_lock, flags); - retval = mii_info->mdio_read(mii_info->dev, mii_info->mii_id, regnum); - spin_unlock_irqrestore(&mii_info->mdio_lock, flags); - - return retval; -} - -void phy_write(struct gfar_mii_info *mii_info, u16 regnum, u16 val) -{ - unsigned long flags; - - spin_lock_irqsave(&mii_info->mdio_lock, flags); - mii_info->mdio_write(mii_info->dev, - mii_info->mii_id, - regnum, val); - spin_unlock_irqrestore(&mii_info->mdio_lock, flags); -} - -/* Use the PHY ID registers to determine what type of PHY is attached - * to device dev. return a struct phy_info structure describing that PHY - */ -struct phy_info * get_phy_info(struct gfar_mii_info *mii_info) -{ - u16 phy_reg; - u32 phy_ID; - int i; - struct phy_info *theInfo = NULL; - struct net_device *dev = mii_info->dev; - - /* Grab the bits from PHYIR1, and put them in the upper half */ - phy_reg = phy_read(mii_info, MII_PHYSID1); - phy_ID = (phy_reg & 0xffff) << 16; - - /* Grab the bits from PHYIR2, and put them in the lower half */ - phy_reg = phy_read(mii_info, MII_PHYSID2); - phy_ID |= (phy_reg & 0xffff); - - /* loop through all the known PHY types, and find one that */ - /* matches the ID we read from the PHY. */ - for (i = 0; phy_info[i]; i++) - if (phy_info[i]->phy_id == - (phy_ID & phy_info[i]->phy_id_mask)) { - theInfo = phy_info[i]; - break; - } - - /* This shouldn't happen, as we have generic PHY support */ - if (theInfo == NULL) { - printk("%s: PHY id %x is not supported!\n", dev->name, phy_ID); - return NULL; - } else { - printk("%s: PHY is %s (%x)\n", dev->name, theInfo->name, - phy_ID); - } - - return theInfo; -} diff --git a/drivers/net/gianfar_phy.h b/drivers/net/gianfar_phy.h deleted file mode 100644 index 1e9b3abf1e6d..000000000000 --- a/drivers/net/gianfar_phy.h +++ /dev/null @@ -1,213 +0,0 @@ -/* - * drivers/net/gianfar_phy.h - * - * Gianfar Ethernet Driver -- PHY handling - * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560 - * Based on 8260_io/fcc_enet.c - * - * Author: Andy Fleming - * Maintainer: Kumar Gala (kumar.gala@freescale.com) - * - * Copyright (c) 2002-2004 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ -#ifndef __GIANFAR_PHY_H -#define __GIANFAR_PHY_H - -#define MII_end ((u32)-2) -#define MII_read ((u32)-1) - -#define MIIMIND_BUSY 0x00000001 -#define MIIMIND_NOTVALID 0x00000004 - -#define GFAR_AN_TIMEOUT 2000 - -/* 1000BT control (Marvell & BCM54xx at least) */ -#define MII_1000BASETCONTROL 0x09 -#define MII_1000BASETCONTROL_FULLDUPLEXCAP 0x0200 -#define MII_1000BASETCONTROL_HALFDUPLEXCAP 0x0100 - -/* Cicada Extended Control Register 1 */ -#define MII_CIS8201_EXT_CON1 0x17 -#define MII_CIS8201_EXTCON1_INIT 0x0000 - -/* Cicada Interrupt Mask Register */ -#define MII_CIS8201_IMASK 0x19 -#define MII_CIS8201_IMASK_IEN 0x8000 -#define MII_CIS8201_IMASK_SPEED 0x4000 -#define MII_CIS8201_IMASK_LINK 0x2000 -#define MII_CIS8201_IMASK_DUPLEX 0x1000 -#define MII_CIS8201_IMASK_MASK 0xf000 - -/* Cicada Interrupt Status Register */ -#define MII_CIS8201_ISTAT 0x1a -#define MII_CIS8201_ISTAT_STATUS 0x8000 -#define MII_CIS8201_ISTAT_SPEED 0x4000 -#define MII_CIS8201_ISTAT_LINK 0x2000 -#define MII_CIS8201_ISTAT_DUPLEX 0x1000 - -/* Cicada Auxiliary Control/Status Register */ -#define MII_CIS8201_AUX_CONSTAT 0x1c -#define MII_CIS8201_AUXCONSTAT_INIT 0x0004 -#define MII_CIS8201_AUXCONSTAT_DUPLEX 0x0020 -#define MII_CIS8201_AUXCONSTAT_SPEED 0x0018 -#define MII_CIS8201_AUXCONSTAT_GBIT 0x0010 -#define MII_CIS8201_AUXCONSTAT_100 0x0008 - -/* 88E1011 PHY Status Register */ -#define MII_M1011_PHY_SPEC_STATUS 0x11 -#define MII_M1011_PHY_SPEC_STATUS_1000 0x8000 -#define MII_M1011_PHY_SPEC_STATUS_100 0x4000 -#define MII_M1011_PHY_SPEC_STATUS_SPD_MASK 0xc000 -#define MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX 0x2000 -#define MII_M1011_PHY_SPEC_STATUS_RESOLVED 0x0800 -#define MII_M1011_PHY_SPEC_STATUS_LINK 0x0400 - -#define MII_M1011_IEVENT 0x13 -#define MII_M1011_IEVENT_CLEAR 0x0000 - -#define MII_M1011_IMASK 0x12 -#define MII_M1011_IMASK_INIT 0x6400 -#define MII_M1011_IMASK_CLEAR 0x0000 - -#define MII_DM9161_SCR 0x10 -#define MII_DM9161_SCR_INIT 0x0610 - -/* DM9161 Specified Configuration and Status Register */ -#define MII_DM9161_SCSR 0x11 -#define MII_DM9161_SCSR_100F 0x8000 -#define MII_DM9161_SCSR_100H 0x4000 -#define MII_DM9161_SCSR_10F 0x2000 -#define MII_DM9161_SCSR_10H 0x1000 - -/* DM9161 Interrupt Register */ -#define MII_DM9161_INTR 0x15 -#define MII_DM9161_INTR_PEND 0x8000 -#define MII_DM9161_INTR_DPLX_MASK 0x0800 -#define MII_DM9161_INTR_SPD_MASK 0x0400 -#define MII_DM9161_INTR_LINK_MASK 0x0200 -#define MII_DM9161_INTR_MASK 0x0100 -#define MII_DM9161_INTR_DPLX_CHANGE 0x0010 -#define MII_DM9161_INTR_SPD_CHANGE 0x0008 -#define MII_DM9161_INTR_LINK_CHANGE 0x0004 -#define MII_DM9161_INTR_INIT 0x0000 -#define MII_DM9161_INTR_STOP \ -(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \ - | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK) - -/* DM9161 10BT Configuration/Status */ -#define MII_DM9161_10BTCSR 0x12 -#define MII_DM9161_10BTCSR_INIT 0x7800 - -#define MII_BASIC_FEATURES (SUPPORTED_10baseT_Half | \ - SUPPORTED_10baseT_Full | \ - SUPPORTED_100baseT_Half | \ - SUPPORTED_100baseT_Full | \ - SUPPORTED_Autoneg | \ - SUPPORTED_TP | \ - SUPPORTED_MII) - -#define MII_GBIT_FEATURES (MII_BASIC_FEATURES | \ - SUPPORTED_1000baseT_Half | \ - SUPPORTED_1000baseT_Full) - -#define MII_READ_COMMAND 0x00000001 - -#define MII_INTERRUPT_DISABLED 0x0 -#define MII_INTERRUPT_ENABLED 0x1 -/* Taken from mii_if_info and sungem_phy.h */ -struct gfar_mii_info { - /* Information about the PHY type */ - /* And management functions */ - struct phy_info *phyinfo; - - /* forced speed & duplex (no autoneg) - * partner speed & duplex & pause (autoneg) - */ - int speed; - int duplex; - int pause; - - /* The most recently read link state */ - int link; - - /* Enabled Interrupts */ - u32 interrupts; - - u32 advertising; - int autoneg; - int mii_id; - - /* private data pointer */ - /* For use by PHYs to maintain extra state */ - void *priv; - - /* Provided by host chip */ - struct net_device *dev; - - /* A lock to ensure that only one thing can read/write - * the MDIO bus at a time */ - spinlock_t mdio_lock; - - /* Provided by ethernet driver */ - int (*mdio_read) (struct net_device *dev, int mii_id, int reg); - void (*mdio_write) (struct net_device *dev, int mii_id, int reg, int val); -}; - -/* struct phy_info: a structure which defines attributes for a PHY - * - * id will contain a number which represents the PHY. During - * startup, the driver will poll the PHY to find out what its - * UID--as defined by registers 2 and 3--is. The 32-bit result - * gotten from the PHY will be ANDed with phy_id_mask to - * discard any bits which may change based on revision numbers - * unimportant to functionality - * - * There are 6 commands which take a gfar_mii_info structure. - * Each PHY must declare config_aneg, and read_status. - */ -struct phy_info { - u32 phy_id; - char *name; - unsigned int phy_id_mask; - u32 features; - - /* Called to initialize the PHY */ - int (*init)(struct gfar_mii_info *mii_info); - - /* Called to suspend the PHY for power */ - int (*suspend)(struct gfar_mii_info *mii_info); - - /* Reconfigures autonegotiation (or disables it) */ - int (*config_aneg)(struct gfar_mii_info *mii_info); - - /* Determines the negotiated speed and duplex */ - int (*read_status)(struct gfar_mii_info *mii_info); - - /* Clears any pending interrupts */ - int (*ack_interrupt)(struct gfar_mii_info *mii_info); - - /* Enables or disables interrupts */ - int (*config_intr)(struct gfar_mii_info *mii_info); - - /* Clears up any memory if needed */ - void (*close)(struct gfar_mii_info *mii_info); -}; - -struct phy_info *get_phy_info(struct gfar_mii_info *mii_info); -int read_phy_reg(struct net_device *dev, int mii_id, int regnum); -void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value); -void mii_clear_phy_interrupt(struct gfar_mii_info *mii_info); -void mii_configure_phy_interrupt(struct gfar_mii_info *mii_info, u32 interrupts); - -struct dm9161_private { - struct timer_list timer; - int resetdone; -}; - -#endif /* GIANFAR_PHY_H */