From: Roland Vossen Date: Wed, 1 Jun 2011 11:45:19 +0000 (+0200) Subject: staging: brcm80211: cleaned sb* header files X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=b6fe70c3aa866db38b72d1cf84b41c4cae80c87b;p=GitHub%2Fmoto-9609%2Fandroid_kernel_motorola_exynos9610.git staging: brcm80211: cleaned sb* header files Code cleanup. Signed-off-by: Roland Vossen Reviewed-by: Arend van Spriel Signed-off-by: Greg Kroah-Hartman --- diff --git a/drivers/staging/brcm80211/brcmfmac/bcmchip.h b/drivers/staging/brcm80211/brcmfmac/bcmchip.h index c0d4c3bf6d42..08729e1cf3d0 100644 --- a/drivers/staging/brcm80211/brcmfmac/bcmchip.h +++ b/drivers/staging/brcm80211/brcmfmac/bcmchip.h @@ -17,12 +17,6 @@ #ifndef _bcmchip_h_ #define _bcmchip_h_ -/* Core reg address translation */ -#define CORE_CC_REG(base, field) (base + offsetof(chipcregs_t, field)) -#define CORE_BUS_REG(base, field) (base + offsetof(sdpcmd_regs_t, field)) -#define CORE_SB(base, field) \ - (base + SBCONFIGOFF + offsetof(sbconfig_t, field)) - /* bcm4329 */ /* SDIO device core, ID 0x829 */ #define BCM4329_CORE_BUS_BASE 0x18011000 diff --git a/drivers/staging/brcm80211/brcmfmac/dhd_sdio.c b/drivers/staging/brcm80211/brcmfmac/dhd_sdio.c index 383e66a2d10a..0e327b3f52d4 100644 --- a/drivers/staging/brcm80211/brcmfmac/dhd_sdio.c +++ b/drivers/staging/brcm80211/brcmfmac/dhd_sdio.c @@ -230,6 +230,42 @@ typedef struct { /* Flags for SDH calls */ #define F2SYNC (SDIO_REQ_4BYTE | SDIO_REQ_FIXED) +/* sbimstate */ +#define SBIM_IBE 0x20000 /* inbanderror */ +#define SBIM_TO 0x40000 /* timeout */ +#define SBIM_BY 0x01800000 /* busy (sonics >= 2.3) */ +#define SBIM_RJ 0x02000000 /* reject (sonics >= 2.3) */ + +/* sbtmstatelow */ +#define SBTML_RESET 0x0001 /* reset */ +#define SBTML_REJ_MASK 0x0006 /* reject field */ +#define SBTML_REJ 0x0002 /* reject */ +#define SBTML_TMPREJ 0x0004 /* temporary reject, for error recovery */ + +#define SBTML_SICF_SHIFT 16 /* Shift to locate the SI control flags in sbtml */ + +/* sbtmstatehigh */ +#define SBTMH_SERR 0x0001 /* serror */ +#define SBTMH_INT 0x0002 /* interrupt */ +#define SBTMH_BUSY 0x0004 /* busy */ +#define SBTMH_TO 0x0020 /* timeout (sonics >= 2.3) */ + +#define SBTMH_SISF_SHIFT 16 /* Shift to locate the SI status flags in sbtmh */ + +/* sbidlow */ +#define SBIDL_INIT 0x80 /* initiator */ + +/* sbidhigh */ +#define SBIDH_RC_MASK 0x000f /* revision code */ +#define SBIDH_RCE_MASK 0x7000 /* revision code extension field */ +#define SBIDH_RCE_SHIFT 8 +#define SBCOREREV(sbidh) \ + ((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | ((sbidh) & SBIDH_RC_MASK)) +#define SBIDH_CC_MASK 0x8ff0 /* core code */ +#define SBIDH_CC_SHIFT 4 +#define SBIDH_VC_MASK 0xffff0000 /* vendor code */ +#define SBIDH_VC_SHIFT 16 + /* * Conversion of 802.1D priority to precedence level */ @@ -241,6 +277,12 @@ DHD_SPINWAIT_SLEEP_INIT(sdioh_spinwait_sleep); extern int dhdcdc_set_ioctl(dhd_pub_t *dhd, int ifidx, uint cmd, void *buf, uint len); +/* Core reg address translation */ +#define CORE_CC_REG(base, field) (base + offsetof(chipcregs_t, field)) +#define CORE_BUS_REG(base, field) (base + offsetof(sdpcmd_regs_t, field)) +#define CORE_SB(base, field) \ + (base + SBCONFIGOFF + offsetof(sbconfig_t, field)) + #ifdef DHD_DEBUG /* Device console log buffer state */ typedef struct dhd_console { @@ -407,6 +449,50 @@ typedef struct dhd_bus { bool ctrl_frame_stat; } dhd_bus_t; +#ifndef _LANGUAGE_ASSEMBLY + +typedef volatile struct _sbconfig { + u32 PAD[2]; + u32 sbipsflag; /* initiator port ocp slave flag */ + u32 PAD[3]; + u32 sbtpsflag; /* target port ocp slave flag */ + u32 PAD[11]; + u32 sbtmerrloga; /* (sonics >= 2.3) */ + u32 PAD; + u32 sbtmerrlog; /* (sonics >= 2.3) */ + u32 PAD[3]; + u32 sbadmatch3; /* address match3 */ + u32 PAD; + u32 sbadmatch2; /* address match2 */ + u32 PAD; + u32 sbadmatch1; /* address match1 */ + u32 PAD[7]; + u32 sbimstate; /* initiator agent state */ + u32 sbintvec; /* interrupt mask */ + u32 sbtmstatelow; /* target state */ + u32 sbtmstatehigh; /* target state */ + u32 sbbwa0; /* bandwidth allocation table0 */ + u32 PAD; + u32 sbimconfiglow; /* initiator configuration */ + u32 sbimconfighigh; /* initiator configuration */ + u32 sbadmatch0; /* address match0 */ + u32 PAD; + u32 sbtmconfiglow; /* target configuration */ + u32 sbtmconfighigh; /* target configuration */ + u32 sbbconfig; /* broadcast configuration */ + u32 PAD; + u32 sbbstate; /* broadcast state */ + u32 PAD[3]; + u32 sbactcnfg; /* activate configuration */ + u32 PAD[3]; + u32 sbflagst; /* current sbflags */ + u32 PAD[3]; + u32 sbidlow; /* identification */ + u32 sbidhigh; /* identification */ +} sbconfig_t; + +#endif /* _LANGUAGE_ASSEMBLY */ + /* clkstate */ #define CLK_NONE 0 #define CLK_SDONLY 1 diff --git a/drivers/staging/brcm80211/brcmfmac/sbsdio.h b/drivers/staging/brcm80211/brcmfmac/sbsdio.h new file mode 100644 index 000000000000..c7facd3795a0 --- /dev/null +++ b/drivers/staging/brcm80211/brcmfmac/sbsdio.h @@ -0,0 +1,152 @@ +/* + * Copyright (c) 2010 Broadcom Corporation + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY + * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION + * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN + * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef _SBSDIO_H +#define _SBSDIO_H + +#define SBSDIO_NUM_FUNCTION 3 /* as of sdiod rev 0, supports 3 functions */ + +/* function 1 miscellaneous registers */ +#define SBSDIO_SPROM_CS 0x10000 /* sprom command and status */ +#define SBSDIO_SPROM_INFO 0x10001 /* sprom info register */ +#define SBSDIO_SPROM_DATA_LOW 0x10002 /* sprom indirect access data byte 0 */ +#define SBSDIO_SPROM_DATA_HIGH 0x10003 /* sprom indirect access data byte 1 */ +#define SBSDIO_SPROM_ADDR_LOW 0x10004 /* sprom indirect access addr byte 0 */ +#define SBSDIO_SPROM_ADDR_HIGH 0x10005 /* sprom indirect access addr byte 0 */ +#define SBSDIO_CHIP_CTRL_DATA 0x10006 /* xtal_pu (gpio) output */ +#define SBSDIO_CHIP_CTRL_EN 0x10007 /* xtal_pu (gpio) enable */ +#define SBSDIO_WATERMARK 0x10008 /* rev < 7, watermark for sdio device */ +#define SBSDIO_DEVICE_CTL 0x10009 /* control busy signal generation */ + +/* registers introduced in rev 8, some content (mask/bits) defs in sbsdpcmdev.h */ +#define SBSDIO_FUNC1_SBADDRLOW 0x1000A /* SB Address Window Low (b15) */ +#define SBSDIO_FUNC1_SBADDRMID 0x1000B /* SB Address Window Mid (b23:b16) */ +#define SBSDIO_FUNC1_SBADDRHIGH 0x1000C /* SB Address Window High (b31:b24) */ +#define SBSDIO_FUNC1_FRAMECTRL 0x1000D /* Frame Control (frame term/abort) */ +#define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E /* ChipClockCSR (ALP/HT ctl/status) */ +#define SBSDIO_FUNC1_SDIOPULLUP 0x1000F /* SdioPullUp (on cmd, d0-d2) */ +#define SBSDIO_FUNC1_WFRAMEBCLO 0x10019 /* Write Frame Byte Count Low */ +#define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A /* Write Frame Byte Count High */ +#define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B /* Read Frame Byte Count Low */ +#define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C /* Read Frame Byte Count High */ + +#define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */ +#define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001C /* f1 misc register end */ + +/* SBSDIO_SPROM_CS */ +#define SBSDIO_SPROM_IDLE 0 +#define SBSDIO_SPROM_WRITE 1 +#define SBSDIO_SPROM_READ 2 +#define SBSDIO_SPROM_WEN 4 +#define SBSDIO_SPROM_WDS 7 +#define SBSDIO_SPROM_DONE 8 + +/* SBSDIO_SPROM_INFO */ +#define SROM_SZ_MASK 0x03 /* SROM size, 1: 4k, 2: 16k */ +#define SROM_BLANK 0x04 /* depreciated in corerev 6 */ +#define SROM_OTP 0x80 /* OTP present */ + +/* SBSDIO_CHIP_CTRL */ +#define SBSDIO_CHIP_CTRL_XTAL 0x01 /* or'd with onchip xtal_pu, + * 1: power on oscillator + * (for 4318 only) + */ +/* SBSDIO_WATERMARK */ +#define SBSDIO_WATERMARK_MASK 0x7f /* number of words - 1 for sd device + * to wait before sending data to host + */ + +/* SBSDIO_DEVICE_CTL */ +#define SBSDIO_DEVCTL_SETBUSY 0x01 /* 1: device will assert busy signal when + * receiving CMD53 + */ +#define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 /* 1: assertion of sdio interrupt is + * synchronous to the sdio clock + */ +#define SBSDIO_DEVCTL_CA_INT_ONLY 0x04 /* 1: mask all interrupts to host + * except the chipActive (rev 8) + */ +#define SBSDIO_DEVCTL_PADS_ISO 0x08 /* 1: isolate internal sdio signals, put + * external pads in tri-state; requires + * sdio bus power cycle to clear (rev 9) + */ +#define SBSDIO_DEVCTL_SB_RST_CTL 0x30 /* Force SD->SB reset mapping (rev 11) */ +#define SBSDIO_DEVCTL_RST_CORECTL 0x00 /* Determined by CoreControl bit */ +#define SBSDIO_DEVCTL_RST_BPRESET 0x10 /* Force backplane reset */ +#define SBSDIO_DEVCTL_RST_NOBPRESET 0x20 /* Force no backplane reset */ + +/* SBSDIO_FUNC1_CHIPCLKCSR */ +#define SBSDIO_FORCE_ALP 0x01 /* Force ALP request to backplane */ +#define SBSDIO_FORCE_HT 0x02 /* Force HT request to backplane */ +#define SBSDIO_FORCE_ILP 0x04 /* Force ILP request to backplane */ +#define SBSDIO_ALP_AVAIL_REQ 0x08 /* Make ALP ready (power up xtal) */ +#define SBSDIO_HT_AVAIL_REQ 0x10 /* Make HT ready (power up PLL) */ +#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20 /* Squelch clock requests from HW */ +#define SBSDIO_ALP_AVAIL 0x40 /* Status: ALP is ready */ +#define SBSDIO_HT_AVAIL 0x80 /* Status: HT is ready */ +/* In rev8, actual avail bits followed original docs */ +#define SBSDIO_Rev8_HT_AVAIL 0x40 +#define SBSDIO_Rev8_ALP_AVAIL 0x80 + +#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL) +#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS) +#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS) +#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval)) +#define SBSDIO_CLKAV(regval, alponly) (SBSDIO_ALPAV(regval) && \ + (alponly ? 1 : SBSDIO_HTAV(regval))) + +/* SBSDIO_FUNC1_SDIOPULLUP */ +#define SBSDIO_PULLUP_D0 0x01 /* Enable D0/MISO pullup */ +#define SBSDIO_PULLUP_D1 0x02 /* Enable D1/INT# pullup */ +#define SBSDIO_PULLUP_D2 0x04 /* Enable D2 pullup */ +#define SBSDIO_PULLUP_CMD 0x08 /* Enable CMD/MOSI pullup */ +#define SBSDIO_PULLUP_ALL 0x0f /* All valid bits */ + +/* function 1 OCP space */ +#define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF /* sb offset addr is <= 15 bits, 32k */ +#define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000 +#define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 /* with b15, maps to 32-bit SB access */ + +/* some duplication with sbsdpcmdev.h here */ +/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */ +#define SBSDIO_SBADDRLOW_MASK 0x80 /* Valid bits in SBADDRLOW */ +#define SBSDIO_SBADDRMID_MASK 0xff /* Valid bits in SBADDRMID */ +#define SBSDIO_SBADDRHIGH_MASK 0xffU /* Valid bits in SBADDRHIGH */ +#define SBSDIO_SBWINDOW_MASK 0xffff8000 /* Address bits from SBADDR regs */ + +/* direct(mapped) cis space */ +#define SBSDIO_CIS_BASE_COMMON 0x1000 /* MAPPED common CIS address */ +#define SBSDIO_CIS_SIZE_LIMIT 0x200 /* maximum bytes in one CIS */ +#define SBSDIO_OTP_CIS_SIZE_LIMIT 0x078 /* maximum bytes OTP CIS */ + +#define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF /* cis offset addr is < 17 bits */ + +#define SBSDIO_CIS_MANFID_TUPLE_LEN 6 /* manfid tuple length, include tuple, + * link bytes + */ + +/* indirect cis access (in sprom) */ +#define SBSDIO_SPROM_CIS_OFFSET 0x8 /* 8 control bytes first, CIS starts from + * 8th byte + */ + +#define SBSDIO_BYTEMODE_DATALEN_MAX 64 /* sdio byte mode: maximum length of one + * data command + */ + +#define SBSDIO_CORE_ADDR_MASK 0x1FFFF /* sdio core function one address mask */ + +#endif /* _SBSDIO_H */ diff --git a/drivers/staging/brcm80211/brcmfmac/sbsdpcmdev.h b/drivers/staging/brcm80211/brcmfmac/sbsdpcmdev.h new file mode 100644 index 000000000000..76266db7bc67 --- /dev/null +++ b/drivers/staging/brcm80211/brcmfmac/sbsdpcmdev.h @@ -0,0 +1,302 @@ +/* + * Copyright (c) 2010 Broadcom Corporation + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY + * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION + * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN + * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef _sbsdpcmdev_h_ +#define _sbsdpcmdev_h_ + +/* cpp contortions to concatenate w/arg prescan */ +#ifndef PAD +#define _PADLINE(line) pad ## line +#define _XSTR(line) _PADLINE(line) +#define PAD _XSTR(__LINE__) +#endif /* PAD */ + +/* dma registers per channel(xmt or rcv) */ +typedef volatile struct { + u32 control; /* enable, et al */ + u32 addr; /* descriptor ring base address (4K aligned) */ + u32 ptr; /* last descriptor posted to chip */ + u32 status; /* current active descriptor, et al */ +} dma32regs_t; + +typedef volatile struct { + dma32regs_t xmt; /* dma tx channel */ + dma32regs_t rcv; /* dma rx channel */ +} dma32regp_t; + +typedef volatile struct { + dma64regs_t xmt; /* dma tx */ + u32 PAD[2]; + dma64regs_t rcv; /* dma rx */ + u32 PAD[2]; +} dma64p_t; + + +typedef volatile struct { /* diag access */ + u32 fifoaddr; /* diag address */ + u32 fifodatalow; /* low 32bits of data */ + u32 fifodatahigh; /* high 32bits of data */ + u32 pad; /* reserved */ +} dma64diag_t; + +/* dma64 sdiod corerev >= 1 */ +typedef volatile struct { + dma64p_t dma64regs[2]; + dma64diag_t dmafifo; /* DMA Diagnostic Regs, 0x280-0x28c */ + u32 PAD[92]; +} sdiodma64_t; + +/* dma32 sdiod corerev == 0 */ +typedef volatile struct { + dma32regp_t dma32regs[2]; /* dma tx & rx, 0x200-0x23c */ + dma32diag_t dmafifo; /* DMA Diagnostic Regs, 0x240-0x24c */ + u32 PAD[108]; +} sdiodma32_t; + +/* dma32 regs for pcmcia core */ +typedef volatile struct { + dma32regp_t dmaregs; /* DMA Regs, 0x200-0x21c, rev8 */ + dma32diag_t dmafifo; /* DMA Diagnostic Regs, 0x220-0x22c */ + u32 PAD[116]; +} pcmdma32_t; + +/* core registers */ +typedef volatile struct { + u32 corecontrol; /* CoreControl, 0x000, rev8 */ + u32 corestatus; /* CoreStatus, 0x004, rev8 */ + u32 PAD[1]; + u32 biststatus; /* BistStatus, 0x00c, rev8 */ + + /* PCMCIA access */ + u16 pcmciamesportaladdr; /* PcmciaMesPortalAddr, 0x010, rev8 */ + u16 PAD[1]; + u16 pcmciamesportalmask; /* PcmciaMesPortalMask, 0x014, rev8 */ + u16 PAD[1]; + u16 pcmciawrframebc; /* PcmciaWrFrameBC, 0x018, rev8 */ + u16 PAD[1]; + u16 pcmciaunderflowtimer; /* PcmciaUnderflowTimer, 0x01c, rev8 */ + u16 PAD[1]; + + /* interrupt */ + u32 intstatus; /* IntStatus, 0x020, rev8 */ + u32 hostintmask; /* IntHostMask, 0x024, rev8 */ + u32 intmask; /* IntSbMask, 0x028, rev8 */ + u32 sbintstatus; /* SBIntStatus, 0x02c, rev8 */ + u32 sbintmask; /* SBIntMask, 0x030, rev8 */ + u32 funcintmask; /* SDIO Function Interrupt Mask, SDIO rev4 */ + u32 PAD[2]; + u32 tosbmailbox; /* ToSBMailbox, 0x040, rev8 */ + u32 tohostmailbox; /* ToHostMailbox, 0x044, rev8 */ + u32 tosbmailboxdata; /* ToSbMailboxData, 0x048, rev8 */ + u32 tohostmailboxdata; /* ToHostMailboxData, 0x04c, rev8 */ + + /* synchronized access to registers in SDIO clock domain */ + u32 sdioaccess; /* SdioAccess, 0x050, rev8 */ + u32 PAD[3]; + + /* PCMCIA frame control */ + u8 pcmciaframectrl; /* pcmciaFrameCtrl, 0x060, rev8 */ + u8 PAD[3]; + u8 pcmciawatermark; /* pcmciaWaterMark, 0x064, rev8 */ + u8 PAD[155]; + + /* interrupt batching control */ + u32 intrcvlazy; /* IntRcvLazy, 0x100, rev8 */ + u32 PAD[3]; + + /* counters */ + u32 cmd52rd; /* Cmd52RdCount, 0x110, rev8, SDIO: cmd52 reads */ + u32 cmd52wr; /* Cmd52WrCount, 0x114, rev8, SDIO: cmd52 writes */ + u32 cmd53rd; /* Cmd53RdCount, 0x118, rev8, SDIO: cmd53 reads */ + u32 cmd53wr; /* Cmd53WrCount, 0x11c, rev8, SDIO: cmd53 writes */ + u32 abort; /* AbortCount, 0x120, rev8, SDIO: aborts */ + u32 datacrcerror; /* DataCrcErrorCount, 0x124, rev8, SDIO: frames w/bad CRC */ + u32 rdoutofsync; /* RdOutOfSyncCount, 0x128, rev8, SDIO/PCMCIA: Rd Frm OOS */ + u32 wroutofsync; /* RdOutOfSyncCount, 0x12c, rev8, SDIO/PCMCIA: Wr Frm OOS */ + u32 writebusy; /* WriteBusyCount, 0x130, rev8, SDIO: dev asserted "busy" */ + u32 readwait; /* ReadWaitCount, 0x134, rev8, SDIO: read: no data avail */ + u32 readterm; /* ReadTermCount, 0x138, rev8, SDIO: rd frm terminates */ + u32 writeterm; /* WriteTermCount, 0x13c, rev8, SDIO: wr frm terminates */ + u32 PAD[40]; + u32 clockctlstatus; /* ClockCtlStatus, 0x1e0, rev8 */ + u32 PAD[7]; + + /* DMA engines */ + volatile union { + pcmdma32_t pcm32; + sdiodma32_t sdiod32; + sdiodma64_t sdiod64; + } dma; + + /* SDIO/PCMCIA CIS region */ + char cis[512]; /* 512 byte CIS, 0x400-0x5ff, rev6 */ + + /* PCMCIA function control registers */ + char pcmciafcr[256]; /* PCMCIA FCR, 0x600-6ff, rev6 */ + u16 PAD[55]; + + /* PCMCIA backplane access */ + u16 backplanecsr; /* BackplaneCSR, 0x76E, rev6 */ + u16 backplaneaddr0; /* BackplaneAddr0, 0x770, rev6 */ + u16 backplaneaddr1; /* BackplaneAddr1, 0x772, rev6 */ + u16 backplaneaddr2; /* BackplaneAddr2, 0x774, rev6 */ + u16 backplaneaddr3; /* BackplaneAddr3, 0x776, rev6 */ + u16 backplanedata0; /* BackplaneData0, 0x778, rev6 */ + u16 backplanedata1; /* BackplaneData1, 0x77a, rev6 */ + u16 backplanedata2; /* BackplaneData2, 0x77c, rev6 */ + u16 backplanedata3; /* BackplaneData3, 0x77e, rev6 */ + u16 PAD[31]; + + /* sprom "size" & "blank" info */ + u16 spromstatus; /* SPROMStatus, 0x7BE, rev2 */ + u32 PAD[464]; + + /* Sonics SiliconBackplane registers */ + u16 PAD[0x80]; /* SbConfig Regs, 0xf00-0xfff, rev8 */ +} sdpcmd_regs_t; + +/* corecontrol */ +#define CC_CISRDY (1 << 0) /* CIS Ready */ +#define CC_BPRESEN (1 << 1) /* CCCR RES signal causes backplane reset */ +#define CC_F2RDY (1 << 2) /* set CCCR IOR2 bit */ +#define CC_CLRPADSISO (1 << 3) /* clear SDIO pads isolation bit (rev 11) */ +#define CC_XMTDATAAVAIL_MODE (1 << 4) /* data avail generates an interrupt */ +#define CC_XMTDATAAVAIL_CTRL (1 << 5) /* data avail interrupt ctrl */ + +/* corestatus */ +#define CS_PCMCIAMODE (1 << 0) /* Device Mode; 0=SDIO, 1=PCMCIA */ +#define CS_SMARTDEV (1 << 1) /* 1=smartDev enabled */ +#define CS_F2ENABLED (1 << 2) /* 1=host has enabled the device */ + +#define PCMCIA_MES_PA_MASK 0x7fff /* PCMCIA Message Portal Address Mask */ +#define PCMCIA_MES_PM_MASK 0x7fff /* PCMCIA Message Portal Mask Mask */ +#define PCMCIA_WFBC_MASK 0xffff /* PCMCIA Write Frame Byte Count Mask */ +#define PCMCIA_UT_MASK 0x07ff /* PCMCIA Underflow Timer Mask */ + +/* intstatus */ +#define I_SMB_SW0 (1 << 0) /* To SB Mail S/W interrupt 0 */ +#define I_SMB_SW1 (1 << 1) /* To SB Mail S/W interrupt 1 */ +#define I_SMB_SW2 (1 << 2) /* To SB Mail S/W interrupt 2 */ +#define I_SMB_SW3 (1 << 3) /* To SB Mail S/W interrupt 3 */ +#define I_SMB_SW_MASK 0x0000000f /* To SB Mail S/W interrupts mask */ +#define I_SMB_SW_SHIFT 0 /* To SB Mail S/W interrupts shift */ +#define I_HMB_SW0 (1 << 4) /* To Host Mail S/W interrupt 0 */ +#define I_HMB_SW1 (1 << 5) /* To Host Mail S/W interrupt 1 */ +#define I_HMB_SW2 (1 << 6) /* To Host Mail S/W interrupt 2 */ +#define I_HMB_SW3 (1 << 7) /* To Host Mail S/W interrupt 3 */ +#define I_HMB_SW_MASK 0x000000f0 /* To Host Mail S/W interrupts mask */ +#define I_HMB_SW_SHIFT 4 /* To Host Mail S/W interrupts shift */ +#define I_WR_OOSYNC (1 << 8) /* Write Frame Out Of Sync */ +#define I_RD_OOSYNC (1 << 9) /* Read Frame Out Of Sync */ +#define I_PC (1 << 10) /* descriptor error */ +#define I_PD (1 << 11) /* data error */ +#define I_DE (1 << 12) /* Descriptor protocol Error */ +#define I_RU (1 << 13) /* Receive descriptor Underflow */ +#define I_RO (1 << 14) /* Receive fifo Overflow */ +#define I_XU (1 << 15) /* Transmit fifo Underflow */ +#define I_RI (1 << 16) /* Receive Interrupt */ +#define I_BUSPWR (1 << 17) /* SDIO Bus Power Change (rev 9) */ +#define I_XMTDATA_AVAIL (1 << 23) /* bits in fifo */ +#define I_XI (1 << 24) /* Transmit Interrupt */ +#define I_RF_TERM (1 << 25) /* Read Frame Terminate */ +#define I_WF_TERM (1 << 26) /* Write Frame Terminate */ +#define I_PCMCIA_XU (1 << 27) /* PCMCIA Transmit FIFO Underflow */ +#define I_SBINT (1 << 28) /* sbintstatus Interrupt */ +#define I_CHIPACTIVE (1 << 29) /* chip transitioned from doze to active state */ +#define I_SRESET (1 << 30) /* CCCR RES interrupt */ +#define I_IOE2 (1U << 31) /* CCCR IOE2 Bit Changed */ +#define I_ERRORS (I_PC | I_PD | I_DE | I_RU | I_RO | I_XU) /* DMA Errors */ +#define I_DMA (I_RI | I_XI | I_ERRORS) + +/* sbintstatus */ +#define I_SB_SERR (1 << 8) /* Backplane SError (write) */ +#define I_SB_RESPERR (1 << 9) /* Backplane Response Error (read) */ +#define I_SB_SPROMERR (1 << 10) /* Error accessing the sprom */ + +/* sdioaccess */ +#define SDA_DATA_MASK 0x000000ff /* Read/Write Data Mask */ +#define SDA_ADDR_MASK 0x000fff00 /* Read/Write Address Mask */ +#define SDA_ADDR_SHIFT 8 /* Read/Write Address Shift */ +#define SDA_WRITE 0x01000000 /* Write bit */ +#define SDA_READ 0x00000000 /* Write bit cleared for Read */ +#define SDA_BUSY 0x80000000 /* Busy bit */ + +/* sdioaccess-accessible register address spaces */ +#define SDA_CCCR_SPACE 0x000 /* sdioAccess CCCR register space */ +#define SDA_F1_FBR_SPACE 0x100 /* sdioAccess F1 FBR register space */ +#define SDA_F2_FBR_SPACE 0x200 /* sdioAccess F2 FBR register space */ +#define SDA_F1_REG_SPACE 0x300 /* sdioAccess F1 core-specific register space */ + +/* SDA_F1_REG_SPACE sdioaccess-accessible F1 reg space register offsets */ +#define SDA_CHIPCONTROLDATA 0x006 /* ChipControlData */ +#define SDA_CHIPCONTROLENAB 0x007 /* ChipControlEnable */ +#define SDA_F2WATERMARK 0x008 /* Function 2 Watermark */ +#define SDA_DEVICECONTROL 0x009 /* DeviceControl */ +#define SDA_SBADDRLOW 0x00a /* SbAddrLow */ +#define SDA_SBADDRMID 0x00b /* SbAddrMid */ +#define SDA_SBADDRHIGH 0x00c /* SbAddrHigh */ +#define SDA_FRAMECTRL 0x00d /* FrameCtrl */ +#define SDA_CHIPCLOCKCSR 0x00e /* ChipClockCSR */ +#define SDA_SDIOPULLUP 0x00f /* SdioPullUp */ +#define SDA_SDIOWRFRAMEBCLOW 0x019 /* SdioWrFrameBCLow */ +#define SDA_SDIOWRFRAMEBCHIGH 0x01a /* SdioWrFrameBCHigh */ +#define SDA_SDIORDFRAMEBCLOW 0x01b /* SdioRdFrameBCLow */ +#define SDA_SDIORDFRAMEBCHIGH 0x01c /* SdioRdFrameBCHigh */ + +/* SDA_F2WATERMARK */ +#define SDA_F2WATERMARK_MASK 0x7f /* F2Watermark Mask */ + +/* SDA_SBADDRLOW */ +#define SDA_SBADDRLOW_MASK 0x80 /* SbAddrLow Mask */ + +/* SDA_SBADDRMID */ +#define SDA_SBADDRMID_MASK 0xff /* SbAddrMid Mask */ + +/* SDA_SBADDRHIGH */ +#define SDA_SBADDRHIGH_MASK 0xff /* SbAddrHigh Mask */ + +/* SDA_FRAMECTRL */ +#define SFC_RF_TERM (1 << 0) /* Read Frame Terminate */ +#define SFC_WF_TERM (1 << 1) /* Write Frame Terminate */ +#define SFC_CRC4WOOS (1 << 2) /* HW reports CRC error for write out of sync */ +#define SFC_ABORTALL (1 << 3) /* Abort cancels all in-progress frames */ + +/* pcmciaframectrl */ +#define PFC_RF_TERM (1 << 0) /* Read Frame Terminate */ +#define PFC_WF_TERM (1 << 1) /* Write Frame Terminate */ + +/* intrcvlazy */ +#define IRL_TO_MASK 0x00ffffff /* timeout */ +#define IRL_FC_MASK 0xff000000 /* frame count */ +#define IRL_FC_SHIFT 24 /* frame count */ + +/* rx header */ +typedef volatile struct { + u16 len; + u16 flags; +} sdpcmd_rxh_t; + +/* rx header flags */ +#define RXF_CRC 0x0001 /* CRC error detected */ +#define RXF_WOOS 0x0002 /* write frame out of sync */ +#define RXF_WF_TERM 0x0004 /* write frame terminated */ +#define RXF_ABORT 0x0008 /* write frame aborted */ +#define RXF_DISCARD (RXF_CRC | RXF_WOOS | RXF_WF_TERM | RXF_ABORT) /* bad frame */ + +/* HW frame tag */ +#define SDPCM_FRAMETAG_LEN 4 /* HW frametag: 2 bytes len, 2 bytes check val */ + +#endif /* _sbsdpcmdev_h_ */ diff --git a/drivers/staging/brcm80211/brcmfmac/sdio.h b/drivers/staging/brcm80211/brcmfmac/sdio.h new file mode 100644 index 000000000000..670e379b9aac --- /dev/null +++ b/drivers/staging/brcm80211/brcmfmac/sdio.h @@ -0,0 +1,552 @@ +/* + * Copyright (c) 2010 Broadcom Corporation + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY + * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION + * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN + * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef _SDIO_H +#define _SDIO_H + +#ifdef BCMSDIO + +/* CCCR structure for function 0 */ +typedef volatile struct { + u8 cccr_sdio_rev; /* RO, cccr and sdio revision */ + u8 sd_rev; /* RO, sd spec revision */ + u8 io_en; /* I/O enable */ + u8 io_rdy; /* I/O ready reg */ + u8 intr_ctl; /* Master and per function interrupt enable control */ + u8 intr_status; /* RO, interrupt pending status */ + u8 io_abort; /* read/write abort or reset all functions */ + u8 bus_inter; /* bus interface control */ + u8 capability; /* RO, card capability */ + + u8 cis_base_low; /* 0x9 RO, common CIS base address, LSB */ + u8 cis_base_mid; + u8 cis_base_high; /* 0xB RO, common CIS base address, MSB */ + + /* suspend/resume registers */ + u8 bus_suspend; /* 0xC */ + u8 func_select; /* 0xD */ + u8 exec_flag; /* 0xE */ + u8 ready_flag; /* 0xF */ + + u8 fn0_blk_size[2]; /* 0x10(LSB), 0x11(MSB) */ + + u8 power_control; /* 0x12 (SDIO version 1.10) */ + + u8 speed_control; /* 0x13 */ +} sdio_regs_t; + +/* SDIO Device CCCR offsets */ +#define SDIOD_CCCR_REV 0x00 +#define SDIOD_CCCR_SDREV 0x01 +#define SDIOD_CCCR_IOEN 0x02 +#define SDIOD_CCCR_IORDY 0x03 +#define SDIOD_CCCR_INTEN 0x04 +#define SDIOD_CCCR_INTPEND 0x05 +#define SDIOD_CCCR_IOABORT 0x06 +#define SDIOD_CCCR_BICTRL 0x07 +#define SDIOD_CCCR_CAPABLITIES 0x08 +#define SDIOD_CCCR_CISPTR_0 0x09 +#define SDIOD_CCCR_CISPTR_1 0x0A +#define SDIOD_CCCR_CISPTR_2 0x0B +#define SDIOD_CCCR_BUSSUSP 0x0C +#define SDIOD_CCCR_FUNCSEL 0x0D +#define SDIOD_CCCR_EXECFLAGS 0x0E +#define SDIOD_CCCR_RDYFLAGS 0x0F +#define SDIOD_CCCR_BLKSIZE_0 0x10 +#define SDIOD_CCCR_BLKSIZE_1 0x11 +#define SDIOD_CCCR_POWER_CONTROL 0x12 +#define SDIOD_CCCR_SPEED_CONTROL 0x13 + +/* Broadcom extensions (corerev >= 1) */ +#define SDIOD_CCCR_BRCM_SEPINT 0xf2 + +/* cccr_sdio_rev */ +#define SDIO_REV_SDIOID_MASK 0xf0 /* SDIO spec revision number */ +#define SDIO_REV_CCCRID_MASK 0x0f /* CCCR format version number */ + +/* sd_rev */ +#define SD_REV_PHY_MASK 0x0f /* SD format version number */ + +/* io_en */ +#define SDIO_FUNC_ENABLE_1 0x02 /* function 1 I/O enable */ +#define SDIO_FUNC_ENABLE_2 0x04 /* function 2 I/O enable */ + +/* io_rdys */ +#define SDIO_FUNC_READY_1 0x02 /* function 1 I/O ready */ +#define SDIO_FUNC_READY_2 0x04 /* function 2 I/O ready */ + +/* intr_ctl */ +#define INTR_CTL_MASTER_EN 0x1 /* interrupt enable master */ +#define INTR_CTL_FUNC1_EN 0x2 /* interrupt enable for function 1 */ +#define INTR_CTL_FUNC2_EN 0x4 /* interrupt enable for function 2 */ + +/* intr_status */ +#define INTR_STATUS_FUNC1 0x2 /* interrupt pending for function 1 */ +#define INTR_STATUS_FUNC2 0x4 /* interrupt pending for function 2 */ + +/* io_abort */ +#define IO_ABORT_RESET_ALL 0x08 /* I/O card reset */ +#define IO_ABORT_FUNC_MASK 0x07 /* abort selction: function x */ + +/* bus_inter */ +#define BUS_CARD_DETECT_DIS 0x80 /* Card Detect disable */ +#define BUS_SPI_CONT_INTR_CAP 0x40 /* support continuous SPI interrupt */ +#define BUS_SPI_CONT_INTR_EN 0x20 /* continuous SPI interrupt enable */ +#define BUS_SD_DATA_WIDTH_MASK 0x03 /* bus width mask */ +#define BUS_SD_DATA_WIDTH_4BIT 0x02 /* bus width 4-bit mode */ +#define BUS_SD_DATA_WIDTH_1BIT 0x00 /* bus width 1-bit mode */ + +/* capability */ +#define SDIO_CAP_4BLS 0x80 /* 4-bit support for low speed card */ +#define SDIO_CAP_LSC 0x40 /* low speed card */ +#define SDIO_CAP_E4MI 0x20 /* enable interrupt between block of data in 4-bit mode */ +#define SDIO_CAP_S4MI 0x10 /* support interrupt between block of data in 4-bit mode */ +#define SDIO_CAP_SBS 0x08 /* support suspend/resume */ +#define SDIO_CAP_SRW 0x04 /* support read wait */ +#define SDIO_CAP_SMB 0x02 /* support multi-block transfer */ +#define SDIO_CAP_SDC 0x01 /* Support Direct commands during multi-byte transfer */ + +/* power_control */ +#define SDIO_POWER_SMPC 0x01 /* supports master power control (RO) */ +#define SDIO_POWER_EMPC 0x02 /* enable master power control (allow > 200mA) (RW) */ + +/* speed_control (control device entry into high-speed clocking mode) */ +#define SDIO_SPEED_SHS 0x01 /* supports high-speed [clocking] mode (RO) */ +#define SDIO_SPEED_EHS 0x02 /* enable high-speed [clocking] mode (RW) */ + +/* brcm sepint */ +#define SDIO_SEPINT_MASK 0x01 /* route sdpcmdev intr onto separate pad (chip-specific) */ +#define SDIO_SEPINT_OE 0x02 /* 1 asserts output enable for above pad */ +#define SDIO_SEPINT_ACT_HI 0x04 /* use active high interrupt level instead of active low */ + +/* FBR structure for function 1-7, FBR addresses and register offsets */ +typedef volatile struct { + u8 devctr; /* device interface, CSA control */ + u8 ext_dev; /* extended standard I/O device type code */ + u8 pwr_sel; /* power selection support */ + u8 PAD[6]; /* reserved */ + + u8 cis_low; /* CIS LSB */ + u8 cis_mid; + u8 cis_high; /* CIS MSB */ + u8 csa_low; /* code storage area, LSB */ + u8 csa_mid; + u8 csa_high; /* code storage area, MSB */ + u8 csa_dat_win; /* data access window to function */ + + u8 fnx_blk_size[2]; /* block size, little endian */ +} sdio_fbr_t; + +/* Maximum number of I/O funcs */ +#define SDIOD_MAX_IOFUNCS 7 + +/* SDIO Device FBR Start Address */ +#define SDIOD_FBR_STARTADDR 0x100 + +/* SDIO Device FBR Size */ +#define SDIOD_FBR_SIZE 0x100 + +/* Macro to calculate FBR register base */ +#define SDIOD_FBR_BASE(n) ((n) * 0x100) + +/* Function register offsets */ +#define SDIOD_FBR_DEVCTR 0x00 /* basic info for function */ +#define SDIOD_FBR_EXT_DEV 0x01 /* extended I/O device code */ +#define SDIOD_FBR_PWR_SEL 0x02 /* power selection bits */ + +/* SDIO Function CIS ptr offset */ +#define SDIOD_FBR_CISPTR_0 0x09 +#define SDIOD_FBR_CISPTR_1 0x0A +#define SDIOD_FBR_CISPTR_2 0x0B + +/* Code Storage Area pointer */ +#define SDIOD_FBR_CSA_ADDR_0 0x0C +#define SDIOD_FBR_CSA_ADDR_1 0x0D +#define SDIOD_FBR_CSA_ADDR_2 0x0E +#define SDIOD_FBR_CSA_DATA 0x0F + +/* SDIO Function I/O Block Size */ +#define SDIOD_FBR_BLKSIZE_0 0x10 +#define SDIOD_FBR_BLKSIZE_1 0x11 + +/* devctr */ +#define SDIOD_FBR_DEVCTR_DIC 0x0f /* device interface code */ +#define SDIOD_FBR_DECVTR_CSA 0x40 /* CSA support flag */ +#define SDIOD_FBR_DEVCTR_CSA_EN 0x80 /* CSA enabled */ +/* interface codes */ +#define SDIOD_DIC_NONE 0 /* SDIO standard interface is not supported */ +#define SDIOD_DIC_UART 1 +#define SDIOD_DIC_BLUETOOTH_A 2 +#define SDIOD_DIC_BLUETOOTH_B 3 +#define SDIOD_DIC_GPS 4 +#define SDIOD_DIC_CAMERA 5 +#define SDIOD_DIC_PHS 6 +#define SDIOD_DIC_WLAN 7 +#define SDIOD_DIC_EXT 0xf /* extended device interface, read ext_dev register */ + +/* pwr_sel */ +#define SDIOD_PWR_SEL_SPS 0x01 /* supports power selection */ +#define SDIOD_PWR_SEL_EPS 0x02 /* enable power selection (low-current mode) */ + +/* misc defines */ +#define SDIO_FUNC_0 0 +#define SDIO_FUNC_1 1 +#define SDIO_FUNC_2 2 +#define SDIO_FUNC_3 3 +#define SDIO_FUNC_4 4 +#define SDIO_FUNC_5 5 +#define SDIO_FUNC_6 6 +#define SDIO_FUNC_7 7 + +#define SD_CARD_TYPE_UNKNOWN 0 /* bad type or unrecognized */ +#define SD_CARD_TYPE_IO 1 /* IO only card */ +#define SD_CARD_TYPE_MEMORY 2 /* memory only card */ +#define SD_CARD_TYPE_COMBO 3 /* IO and memory combo card */ + +#define SDIO_MAX_BLOCK_SIZE 2048 /* maximum block size for block mode operation */ +#define SDIO_MIN_BLOCK_SIZE 1 /* minimum block size for block mode operation */ + +/* Card registers: status bit position */ +#define CARDREG_STATUS_BIT_OUTOFRANGE 31 +#define CARDREG_STATUS_BIT_COMCRCERROR 23 +#define CARDREG_STATUS_BIT_ILLEGALCOMMAND 22 +#define CARDREG_STATUS_BIT_ERROR 19 +#define CARDREG_STATUS_BIT_IOCURRENTSTATE3 12 +#define CARDREG_STATUS_BIT_IOCURRENTSTATE2 11 +#define CARDREG_STATUS_BIT_IOCURRENTSTATE1 10 +#define CARDREG_STATUS_BIT_IOCURRENTSTATE0 9 +#define CARDREG_STATUS_BIT_FUN_NUM_ERROR 4 + +#define SD_CMD_GO_IDLE_STATE 0 /* mandatory for SDIO */ +#define SD_CMD_SEND_OPCOND 1 +#define SD_CMD_MMC_SET_RCA 3 +#define SD_CMD_IO_SEND_OP_COND 5 /* mandatory for SDIO */ +#define SD_CMD_SELECT_DESELECT_CARD 7 +#define SD_CMD_SEND_CSD 9 +#define SD_CMD_SEND_CID 10 +#define SD_CMD_STOP_TRANSMISSION 12 +#define SD_CMD_SEND_STATUS 13 +#define SD_CMD_GO_INACTIVE_STATE 15 +#define SD_CMD_SET_BLOCKLEN 16 +#define SD_CMD_READ_SINGLE_BLOCK 17 +#define SD_CMD_READ_MULTIPLE_BLOCK 18 +#define SD_CMD_WRITE_BLOCK 24 +#define SD_CMD_WRITE_MULTIPLE_BLOCK 25 +#define SD_CMD_PROGRAM_CSD 27 +#define SD_CMD_SET_WRITE_PROT 28 +#define SD_CMD_CLR_WRITE_PROT 29 +#define SD_CMD_SEND_WRITE_PROT 30 +#define SD_CMD_ERASE_WR_BLK_START 32 +#define SD_CMD_ERASE_WR_BLK_END 33 +#define SD_CMD_ERASE 38 +#define SD_CMD_LOCK_UNLOCK 42 +#define SD_CMD_IO_RW_DIRECT 52 /* mandatory for SDIO */ +#define SD_CMD_IO_RW_EXTENDED 53 /* mandatory for SDIO */ +#define SD_CMD_APP_CMD 55 +#define SD_CMD_GEN_CMD 56 +#define SD_CMD_READ_OCR 58 +#define SD_CMD_CRC_ON_OFF 59 /* mandatory for SDIO */ +#define SD_ACMD_SD_STATUS 13 +#define SD_ACMD_SEND_NUM_WR_BLOCKS 22 +#define SD_ACMD_SET_WR_BLOCK_ERASE_CNT 23 +#define SD_ACMD_SD_SEND_OP_COND 41 +#define SD_ACMD_SET_CLR_CARD_DETECT 42 +#define SD_ACMD_SEND_SCR 51 + +/* argument for SD_CMD_IO_RW_DIRECT and SD_CMD_IO_RW_EXTENDED */ +#define SD_IO_OP_READ 0 /* Read_Write: Read */ +#define SD_IO_OP_WRITE 1 /* Read_Write: Write */ +#define SD_IO_RW_NORMAL 0 /* no RAW */ +#define SD_IO_RW_RAW 1 /* RAW */ +#define SD_IO_BYTE_MODE 0 /* Byte Mode */ +#define SD_IO_BLOCK_MODE 1 /* BlockMode */ +#define SD_IO_FIXED_ADDRESS 0 /* fix Address */ +#define SD_IO_INCREMENT_ADDRESS 1 /* IncrementAddress */ + +/* build SD_CMD_IO_RW_DIRECT Argument */ +#define SDIO_IO_RW_DIRECT_ARG(rw, raw, func, addr, data) \ + ((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((raw) & 1) << 27) | \ + (((addr) & 0x1FFFF) << 9) | ((data) & 0xFF)) + +/* build SD_CMD_IO_RW_EXTENDED Argument */ +#define SDIO_IO_RW_EXTENDED_ARG(rw, blk, func, addr, inc_addr, count) \ + ((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((blk) & 1) << 27) | \ + (((inc_addr) & 1) << 26) | (((addr) & 0x1FFFF) << 9) | ((count) & 0x1FF)) + +/* SDIO response parameters */ +#define SD_RSP_NO_NONE 0 +#define SD_RSP_NO_1 1 +#define SD_RSP_NO_2 2 +#define SD_RSP_NO_3 3 +#define SD_RSP_NO_4 4 +#define SD_RSP_NO_5 5 +#define SD_RSP_NO_6 6 + + /* Modified R6 response (to CMD3) */ +#define SD_RSP_MR6_COM_CRC_ERROR 0x8000 +#define SD_RSP_MR6_ILLEGAL_COMMAND 0x4000 +#define SD_RSP_MR6_ERROR 0x2000 + + /* Modified R1 in R4 Response (to CMD5) */ +#define SD_RSP_MR1_SBIT 0x80 +#define SD_RSP_MR1_PARAMETER_ERROR 0x40 +#define SD_RSP_MR1_RFU5 0x20 +#define SD_RSP_MR1_FUNC_NUM_ERROR 0x10 +#define SD_RSP_MR1_COM_CRC_ERROR 0x08 +#define SD_RSP_MR1_ILLEGAL_COMMAND 0x04 +#define SD_RSP_MR1_RFU1 0x02 +#define SD_RSP_MR1_IDLE_STATE 0x01 + + /* R5 response (to CMD52 and CMD53) */ +#define SD_RSP_R5_COM_CRC_ERROR 0x80 +#define SD_RSP_R5_ILLEGAL_COMMAND 0x40 +#define SD_RSP_R5_IO_CURRENTSTATE1 0x20 +#define SD_RSP_R5_IO_CURRENTSTATE0 0x10 +#define SD_RSP_R5_ERROR 0x08 +#define SD_RSP_R5_RFU 0x04 +#define SD_RSP_R5_FUNC_NUM_ERROR 0x02 +#define SD_RSP_R5_OUT_OF_RANGE 0x01 + +#define SD_RSP_R5_ERRBITS 0xCB + +/* ------------------------------------------------ + * SDIO Commands and responses + * + * I/O only commands are: + * CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53 + * ------------------------------------------------ + */ + +/* SDIO Commands */ +#define SDIOH_CMD_0 0 +#define SDIOH_CMD_3 3 +#define SDIOH_CMD_5 5 +#define SDIOH_CMD_7 7 +#define SDIOH_CMD_15 15 +#define SDIOH_CMD_52 52 +#define SDIOH_CMD_53 53 +#define SDIOH_CMD_59 59 + +/* SDIO Command Responses */ +#define SDIOH_RSP_NONE 0 +#define SDIOH_RSP_R1 1 +#define SDIOH_RSP_R2 2 +#define SDIOH_RSP_R3 3 +#define SDIOH_RSP_R4 4 +#define SDIOH_RSP_R5 5 +#define SDIOH_RSP_R6 6 + +/* + * SDIO Response Error flags + */ +#define SDIOH_RSP5_ERROR_FLAGS 0xCB + +/* ------------------------------------------------ + * SDIO Command structures. I/O only commands are: + * + * CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53 + * ------------------------------------------------ + */ + +#define CMD5_OCR_M BITFIELD_MASK(24) +#define CMD5_OCR_S 0 + +#define CMD7_RCA_M BITFIELD_MASK(16) +#define CMD7_RCA_S 16 + +#define CMD_15_RCA_M BITFIELD_MASK(16) +#define CMD_15_RCA_S 16 + +#define CMD52_DATA_M BITFIELD_MASK(8) /* Bits [7:0] - Write Data/Stuff bits of CMD52 + */ +#define CMD52_DATA_S 0 +#define CMD52_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */ +#define CMD52_REG_ADDR_S 9 +#define CMD52_RAW_M BITFIELD_MASK(1) /* Bit 27 - Read after Write flag */ +#define CMD52_RAW_S 27 +#define CMD52_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */ +#define CMD52_FUNCTION_S 28 +#define CMD52_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */ +#define CMD52_RW_FLAG_S 31 + +#define CMD53_BYTE_BLK_CNT_M BITFIELD_MASK(9) /* Bits [8:0] - Byte/Block Count of CMD53 */ +#define CMD53_BYTE_BLK_CNT_S 0 +#define CMD53_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */ +#define CMD53_REG_ADDR_S 9 +#define CMD53_OP_CODE_M BITFIELD_MASK(1) /* Bit 26 - R/W Operation Code */ +#define CMD53_OP_CODE_S 26 +#define CMD53_BLK_MODE_M BITFIELD_MASK(1) /* Bit 27 - Block Mode */ +#define CMD53_BLK_MODE_S 27 +#define CMD53_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */ +#define CMD53_FUNCTION_S 28 +#define CMD53_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */ +#define CMD53_RW_FLAG_S 31 + +/* ------------------------------------------------------ + * SDIO Command Response structures for SD1 and SD4 modes + * ----------------------------------------------------- + */ +#define RSP4_IO_OCR_M BITFIELD_MASK(24) /* Bits [23:0] - Card's OCR Bits [23:0] */ +#define RSP4_IO_OCR_S 0 +#define RSP4_STUFF_M BITFIELD_MASK(3) /* Bits [26:24] - Stuff bits */ +#define RSP4_STUFF_S 24 +#define RSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 27 - Memory present */ +#define RSP4_MEM_PRESENT_S 27 +#define RSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [30:28] - Number of I/O funcs */ +#define RSP4_NUM_FUNCS_S 28 +#define RSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 31 - SDIO card ready */ +#define RSP4_CARD_READY_S 31 + +#define RSP6_STATUS_M BITFIELD_MASK(16) /* Bits [15:0] - Card status bits [19,22,23,12:0] + */ +#define RSP6_STATUS_S 0 +#define RSP6_IO_RCA_M BITFIELD_MASK(16) /* Bits [31:16] - RCA bits[31-16] */ +#define RSP6_IO_RCA_S 16 + +#define RSP1_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error */ +#define RSP1_AKE_SEQ_ERROR_S 3 +#define RSP1_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */ +#define RSP1_APP_CMD_S 5 +#define RSP1_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data (buff empty) */ +#define RSP1_READY_FOR_DATA_S 8 +#define RSP1_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - State of card + * when Cmd was received + */ +#define RSP1_CURR_STATE_S 9 +#define RSP1_EARSE_RESET_M BITFIELD_MASK(1) /* Bit 13 - Erase seq cleared */ +#define RSP1_EARSE_RESET_S 13 +#define RSP1_CARD_ECC_DISABLE_M BITFIELD_MASK(1) /* Bit 14 - Card ECC disabled */ +#define RSP1_CARD_ECC_DISABLE_S 14 +#define RSP1_WP_ERASE_SKIP_M BITFIELD_MASK(1) /* Bit 15 - Partial blocks erased due to W/P */ +#define RSP1_WP_ERASE_SKIP_S 15 +#define RSP1_CID_CSD_OVERW_M BITFIELD_MASK(1) /* Bit 16 - Illegal write to CID or R/O bits + * of CSD + */ +#define RSP1_CID_CSD_OVERW_S 16 +#define RSP1_ERROR_M BITFIELD_MASK(1) /* Bit 19 - General/Unknown error */ +#define RSP1_ERROR_S 19 +#define RSP1_CC_ERROR_M BITFIELD_MASK(1) /* Bit 20 - Internal Card Control error */ +#define RSP1_CC_ERROR_S 20 +#define RSP1_CARD_ECC_FAILED_M BITFIELD_MASK(1) /* Bit 21 - Card internal ECC failed + * to correct data + */ +#define RSP1_CARD_ECC_FAILED_S 21 +#define RSP1_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 22 - Cmd not legal for the card state */ +#define RSP1_ILLEGAL_CMD_S 22 +#define RSP1_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 23 - CRC check of previous command failed + */ +#define RSP1_COM_CRC_ERROR_S 23 +#define RSP1_LOCK_UNLOCK_FAIL_M BITFIELD_MASK(1) /* Bit 24 - Card lock-unlock Cmd Seq error */ +#define RSP1_LOCK_UNLOCK_FAIL_S 24 +#define RSP1_CARD_LOCKED_M BITFIELD_MASK(1) /* Bit 25 - Card locked by the host */ +#define RSP1_CARD_LOCKED_S 25 +#define RSP1_WP_VIOLATION_M BITFIELD_MASK(1) /* Bit 26 - Attempt to program + * write-protected blocks + */ +#define RSP1_WP_VIOLATION_S 26 +#define RSP1_ERASE_PARAM_M BITFIELD_MASK(1) /* Bit 27 - Invalid erase blocks */ +#define RSP1_ERASE_PARAM_S 27 +#define RSP1_ERASE_SEQ_ERR_M BITFIELD_MASK(1) /* Bit 28 - Erase Cmd seq error */ +#define RSP1_ERASE_SEQ_ERR_S 28 +#define RSP1_BLK_LEN_ERR_M BITFIELD_MASK(1) /* Bit 29 - Block length error */ +#define RSP1_BLK_LEN_ERR_S 29 +#define RSP1_ADDR_ERR_M BITFIELD_MASK(1) /* Bit 30 - Misaligned address */ +#define RSP1_ADDR_ERR_S 30 +#define RSP1_OUT_OF_RANGE_M BITFIELD_MASK(1) /* Bit 31 - Cmd arg was out of range */ +#define RSP1_OUT_OF_RANGE_S 31 + +#define RSP5_DATA_M BITFIELD_MASK(8) /* Bits [0:7] - data */ +#define RSP5_DATA_S 0 +#define RSP5_FLAGS_M BITFIELD_MASK(8) /* Bit [15:8] - Rsp flags */ +#define RSP5_FLAGS_S 8 +#define RSP5_STUFF_M BITFIELD_MASK(16) /* Bits [31:16] - Stuff bits */ +#define RSP5_STUFF_S 16 + +/* ---------------------------------------------- + * SDIO Command Response structures for SPI mode + * ---------------------------------------------- + */ +#define SPIRSP4_IO_OCR_M BITFIELD_MASK(16) /* Bits [15:0] - Card's OCR Bits [23:8] */ +#define SPIRSP4_IO_OCR_S 0 +#define SPIRSP4_STUFF_M BITFIELD_MASK(3) /* Bits [18:16] - Stuff bits */ +#define SPIRSP4_STUFF_S 16 +#define SPIRSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 19 - Memory present */ +#define SPIRSP4_MEM_PRESENT_S 19 +#define SPIRSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [22:20] - Number of I/O funcs */ +#define SPIRSP4_NUM_FUNCS_S 20 +#define SPIRSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 23 - SDIO card ready */ +#define SPIRSP4_CARD_READY_S 23 +#define SPIRSP4_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - idle state */ +#define SPIRSP4_IDLE_STATE_S 24 +#define SPIRSP4_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */ +#define SPIRSP4_ILLEGAL_CMD_S 26 +#define SPIRSP4_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */ +#define SPIRSP4_COM_CRC_ERROR_S 27 +#define SPIRSP4_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error + */ +#define SPIRSP4_FUNC_NUM_ERROR_S 28 +#define SPIRSP4_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */ +#define SPIRSP4_PARAM_ERROR_S 30 +#define SPIRSP4_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */ +#define SPIRSP4_START_BIT_S 31 + +#define SPIRSP5_DATA_M BITFIELD_MASK(8) /* Bits [23:16] - R/W Data */ +#define SPIRSP5_DATA_S 16 +#define SPIRSP5_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - Idle state */ +#define SPIRSP5_IDLE_STATE_S 24 +#define SPIRSP5_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */ +#define SPIRSP5_ILLEGAL_CMD_S 26 +#define SPIRSP5_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */ +#define SPIRSP5_COM_CRC_ERROR_S 27 +#define SPIRSP5_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error + */ +#define SPIRSP5_FUNC_NUM_ERROR_S 28 +#define SPIRSP5_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */ +#define SPIRSP5_PARAM_ERROR_S 30 +#define SPIRSP5_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */ +#define SPIRSP5_START_BIT_S 31 + +/* RSP6 card status format; Pg 68 Physical Layer spec v 1.10 */ +#define RSP6STAT_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error + */ +#define RSP6STAT_AKE_SEQ_ERROR_S 3 +#define RSP6STAT_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */ +#define RSP6STAT_APP_CMD_S 5 +#define RSP6STAT_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data + * (buff empty) + */ +#define RSP6STAT_READY_FOR_DATA_S 8 +#define RSP6STAT_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - Card state at + * Cmd reception + */ +#define RSP6STAT_CURR_STATE_S 9 +#define RSP6STAT_ERROR_M BITFIELD_MASK(1) /* Bit 13 - General/Unknown error Bit 19 + */ +#define RSP6STAT_ERROR_S 13 +#define RSP6STAT_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 14 - Illegal cmd for + * card state Bit 22 + */ +#define RSP6STAT_ILLEGAL_CMD_S 14 +#define RSP6STAT_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 15 - CRC previous command + * failed Bit 23 + */ +#define RSP6STAT_COM_CRC_ERROR_S 15 + +#define SDIOH_XFER_TYPE_READ SD_IO_OP_READ +#define SDIOH_XFER_TYPE_WRITE SD_IO_OP_WRITE + +#endif /* def BCMSDIO */ +#endif /* _SDIO_H */ diff --git a/drivers/staging/brcm80211/brcmsmac/aiutils.c b/drivers/staging/brcm80211/brcmsmac/aiutils.c index 73587b34e25a..9aec0848eb99 100644 --- a/drivers/staging/brcm80211/brcmsmac/aiutils.c +++ b/drivers/staging/brcm80211/brcmsmac/aiutils.c @@ -35,6 +35,134 @@ #include #include +/* slow_clk_ctl */ +#define SCC_SS_MASK 0x00000007 /* slow clock source mask */ +#define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */ +#define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */ +#define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */ +#define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ +#define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled, + * 0: LPO is enabled + */ +#define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, + * 0: power logic control + */ +#define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors + * PLL clock disable requests from core + */ +#define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't + * disable crystal when appropriate + */ +#define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ +#define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ +#define SCC_CD_SHIFT 16 + +/* system_clk_ctl */ +#define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */ +#define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */ +#define SYCC_FP 0x00000004 /* ForcePLLOn */ +#define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */ +#define SYCC_HR 0x00000010 /* Force HT */ +#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */ +#define SYCC_CD_SHIFT 16 + +#define CST4329_SPROM_OTP_SEL_MASK 0x00000003 +#define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ +#define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ +#define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */ +#define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ +#define CST4329_SPI_SDIO_MODE_MASK 0x00000004 +#define CST4329_SPI_SDIO_MODE_SHIFT 2 + +/* 43224 chip-specific ChipControl register bits */ +#define CCTRL43224_GPIO_TOGGLE 0x8000 +#define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */ +#define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */ + +/* 43236 Chip specific ChipStatus register bits */ +#define CST43236_SFLASH_MASK 0x00000040 +#define CST43236_OTP_MASK 0x00000080 +#define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */ +#define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */ +#define CST43236_BOOT_MASK 0x00001800 +#define CST43236_BOOT_SHIFT 11 +#define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ +#define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */ +#define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */ +#define CST43236_BOOT_FROM_INVALID 3 + +/* 4331 chip-specific ChipControl register bits */ +#define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */ +#define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ +#define CCTRL4331_EXT_LNA (1<<2) /* 0 disable */ +#define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */ +#define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */ +#define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */ +#define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */ +#define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */ +#define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */ +#define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */ +#define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */ +#define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */ +#define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */ +#define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */ + +/* 4331 Chip specific ChipStatus register bits */ +#define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */ +#define CST4331_SPROM_PRESENT 0x00000002 +#define CST4331_OTP_PRESENT 0x00000004 +#define CST4331_LDO_RF 0x00000008 +#define CST4331_LDO_PAR 0x00000010 + +/* 4319 chip-specific ChipStatus register bits */ +#define CST4319_SPI_CPULESSUSB 0x00000001 +#define CST4319_SPI_CLK_POL 0x00000002 +#define CST4319_SPI_CLK_PH 0x00000008 +#define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */ +#define CST4319_SPROM_OTP_SEL_SHIFT 6 +#define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */ +#define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */ +#define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */ +#define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */ +#define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */ +#define CST4319_REMAP_SEL_MASK 0x00000600 +#define CST4319_ILPDIV_EN 0x00000800 +#define CST4319_XTAL_PD_POL 0x00001000 +#define CST4319_LPO_SEL 0x00002000 +#define CST4319_RES_INIT_MODE 0x0000c000 +#define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */ +#define CST4319_CBUCK_MODE_MASK 0x00060000 +#define CST4319_CBUCK_MODE_BURST 0x00020000 +#define CST4319_CBUCK_MODE_LPBURST 0x00060000 +#define CST4319_RCAL_VALID 0x01000000 +#define CST4319_RCAL_VALUE_MASK 0x3e000000 +#define CST4319_RCAL_VALUE_SHIFT 25 + +/* 4336 chip-specific ChipStatus register bits */ +#define CST4336_SPI_MODE_MASK 0x00000001 +#define CST4336_SPROM_PRESENT 0x00000002 +#define CST4336_OTP_PRESENT 0x00000004 +#define CST4336_ARMREMAP_0 0x00000008 +#define CST4336_ILPDIV_EN_MASK 0x00000010 +#define CST4336_ILPDIV_EN_SHIFT 4 +#define CST4336_XTAL_PD_POL_MASK 0x00000020 +#define CST4336_XTAL_PD_POL_SHIFT 5 +#define CST4336_LPO_SEL_MASK 0x00000040 +#define CST4336_LPO_SEL_SHIFT 6 +#define CST4336_RES_INIT_MODE_MASK 0x00000180 +#define CST4336_RES_INIT_MODE_SHIFT 7 +#define CST4336_CBUCK_MODE_MASK 0x00000600 +#define CST4336_CBUCK_MODE_SHIFT 9 + +/* 4313 chip-specific ChipStatus register bits */ +#define CST4313_SPROM_PRESENT 1 +#define CST4313_OTP_PRESENT 2 +#define CST4313_SPROM_OTP_SEL_MASK 0x00000002 +#define CST4313_SPROM_OTP_SEL_SHIFT 0 + +/* 4313 Chip specific ChipControl register bits */ +#define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ + #define BCM47162_DMP() ((sih->chip == BCM47162_CHIP_ID) && \ (sih->chiprev == 0) && \ (sii->coreid[sii->curidx] == MIPS74K_CORE_ID)) diff --git a/drivers/staging/brcm80211/brcmsmac/aiutils.h b/drivers/staging/brcm80211/brcmsmac/aiutils.h index b98099eaa621..29415375b6b6 100644 --- a/drivers/staging/brcm80211/brcmsmac/aiutils.h +++ b/drivers/staging/brcm80211/brcmsmac/aiutils.h @@ -225,6 +225,52 @@ #define BISZ_BSSEND_IDX 6 /* 6: bss end */ #define BISZ_SIZE 7 /* descriptor size in 32-bit integers */ +#define CC_SROM_OTP 0x800 /* SROM/OTP address space */ + +/* gpiotimerval */ +#define GPIO_ONTIME_SHIFT 16 + +/* Fields in clkdiv */ +#define CLKD_OTP 0x000f0000 +#define CLKD_OTP_SHIFT 16 + +/* When Srom support present, fields in sromcontrol */ +#define SRC_START 0x80000000 +#define SRC_BUSY 0x80000000 +#define SRC_OPCODE 0x60000000 +#define SRC_OP_READ 0x00000000 +#define SRC_OP_WRITE 0x20000000 +#define SRC_OP_WRDIS 0x40000000 +#define SRC_OP_WREN 0x60000000 +#define SRC_OTPSEL 0x00000010 +#define SRC_LOCK 0x00000008 +#define SRC_SIZE_MASK 0x00000006 +#define SRC_SIZE_1K 0x00000000 +#define SRC_SIZE_4K 0x00000002 +#define SRC_SIZE_16K 0x00000004 +#define SRC_SIZE_SHIFT 1 +#define SRC_PRESENT 0x00000001 + +/* 4330 chip-specific ChipStatus register bits */ +#define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */ +#define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */ +#define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */ +#define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */ +#define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */ +#define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */ +#define CST4330_OTP_PRESENT 0x00000010 +#define CST4330_LPO_AUTODET_EN 0x00000020 +#define CST4330_ARMREMAP_0 0x00000040 +#define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */ +#define CST4330_ILPDIV_EN 0x00000100 +#define CST4330_LPO_SEL 0x00000200 +#define CST4330_RES_INIT_MODE_SHIFT 10 +#define CST4330_RES_INIT_MODE_MASK 0x00000c00 +#define CST4330_CBUCK_MODE_SHIFT 12 +#define CST4330_CBUCK_MODE_MASK 0x00003000 +#define CST4330_CBUCK_POWER_OK 0x00004000 +#define CST4330_BB_PLL_LOCKED 0x00008000 + #define SI_INFO(sih) (si_info_t *)sih #define GOODCOREADDR(x, b) \ diff --git a/drivers/staging/brcm80211/brcmsmac/bcmotp.c b/drivers/staging/brcm80211/brcmsmac/bcmotp.c index d01f60a5f585..aa147c3862a3 100644 --- a/drivers/staging/brcm80211/brcmsmac/bcmotp.c +++ b/drivers/staging/brcm80211/brcmsmac/bcmotp.c @@ -29,6 +29,37 @@ #include #include +#define OTPS_GUP_MASK 0x00000f00 +#define OTPS_GUP_SHIFT 8 +#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */ +#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */ +#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */ +#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */ + +/* Fields in otpprog in rev >= 21 and HND OTP */ +#define OTPP_COL_MASK 0x000000ff +#define OTPP_COL_SHIFT 0 +#define OTPP_ROW_MASK 0x0000ff00 +#define OTPP_ROW_SHIFT 8 +#define OTPP_OC_MASK 0x0f000000 +#define OTPP_OC_SHIFT 24 +#define OTPP_READERR 0x10000000 +#define OTPP_VALUE_MASK 0x20000000 +#define OTPP_VALUE_SHIFT 29 +#define OTPP_START_BUSY 0x80000000 +#define OTPP_READ 0x40000000 /* HND OTP */ + +/* Opcodes for OTPP_OC field */ +#define OTPPOC_READ 0 +#define OTPPOC_BIT_PROG 1 +#define OTPPOC_VERIFY 3 +#define OTPPOC_INIT 4 +#define OTPPOC_SET 5 +#define OTPPOC_RESET 6 +#define OTPPOC_OCST 7 +#define OTPPOC_ROW_LOCK 8 +#define OTPPOC_PRESCN_TEST 9 + /* * There are two different OTP controllers so far: * 1. new IPX OTP controller: chipc 21, >=23 diff --git a/drivers/staging/brcm80211/brcmsmac/d11.h b/drivers/staging/brcm80211/brcmsmac/d11.h index e022224c5128..d1babcd34ec0 100644 --- a/drivers/staging/brcm80211/brcmsmac/d11.h +++ b/drivers/staging/brcm80211/brcmsmac/d11.h @@ -18,7 +18,6 @@ #define _D11_H #include -#include /* cpp contortions to concatenate w/arg prescan */ #ifndef PAD @@ -440,9 +439,6 @@ typedef volatile struct _d11regs { /* SHM *//* 0x800 - 0xEFE */ u16 PAD[0x380]; /* 0x800 - 0xEFE */ - - /* SB configuration registers: 0xF00 */ - sbconfig_t sbconfig; /* sb config regs occupy top 256 bytes */ } d11regs_t; #define PIHR_BASE 0x0400 /* byte address of packed IHR region */ diff --git a/drivers/staging/brcm80211/brcmsmac/dma.c b/drivers/staging/brcm80211/brcmsmac/dma.c index 2557255c5c07..77baef2eebee 100644 --- a/drivers/staging/brcm80211/brcmsmac/dma.c +++ b/drivers/staging/brcm80211/brcmsmac/dma.c @@ -31,6 +31,123 @@ #include #endif +/* + * Each descriptor ring must be 8kB aligned, and fit within a contiguous 8kB physical address. + */ +#define D64RINGALIGN_BITS 13 +#define D64MAXRINGSZ (1 << D64RINGALIGN_BITS) +#define D64RINGALIGN (1 << D64RINGALIGN_BITS) + +#define D64MAXDD (D64MAXRINGSZ / sizeof (dma64dd_t)) + +/* transmit channel control */ +#define D64_XC_XE 0x00000001 /* transmit enable */ +#define D64_XC_SE 0x00000002 /* transmit suspend request */ +#define D64_XC_LE 0x00000004 /* loopback enable */ +#define D64_XC_FL 0x00000010 /* flush request */ +#define D64_XC_PD 0x00000800 /* parity check disable */ +#define D64_XC_AE 0x00030000 /* address extension bits */ +#define D64_XC_AE_SHIFT 16 + +/* transmit descriptor table pointer */ +#define D64_XP_LD_MASK 0x00000fff /* last valid descriptor */ + +/* transmit channel status */ +#define D64_XS0_CD_MASK 0x00001fff /* current descriptor pointer */ +#define D64_XS0_XS_MASK 0xf0000000 /* transmit state */ +#define D64_XS0_XS_SHIFT 28 +#define D64_XS0_XS_DISABLED 0x00000000 /* disabled */ +#define D64_XS0_XS_ACTIVE 0x10000000 /* active */ +#define D64_XS0_XS_IDLE 0x20000000 /* idle wait */ +#define D64_XS0_XS_STOPPED 0x30000000 /* stopped */ +#define D64_XS0_XS_SUSP 0x40000000 /* suspend pending */ + +#define D64_XS1_AD_MASK 0x00001fff /* active descriptor */ +#define D64_XS1_XE_MASK 0xf0000000 /* transmit errors */ +#define D64_XS1_XE_SHIFT 28 +#define D64_XS1_XE_NOERR 0x00000000 /* no error */ +#define D64_XS1_XE_DPE 0x10000000 /* descriptor protocol error */ +#define D64_XS1_XE_DFU 0x20000000 /* data fifo underrun */ +#define D64_XS1_XE_DTE 0x30000000 /* data transfer error */ +#define D64_XS1_XE_DESRE 0x40000000 /* descriptor read error */ +#define D64_XS1_XE_COREE 0x50000000 /* core error */ + +/* receive channel control */ +#define D64_RC_RE 0x00000001 /* receive enable */ +#define D64_RC_RO_MASK 0x000000fe /* receive frame offset */ +#define D64_RC_RO_SHIFT 1 +#define D64_RC_FM 0x00000100 /* direct fifo receive (pio) mode */ +#define D64_RC_SH 0x00000200 /* separate rx header descriptor enable */ +#define D64_RC_OC 0x00000400 /* overflow continue */ +#define D64_RC_PD 0x00000800 /* parity check disable */ +#define D64_RC_AE 0x00030000 /* address extension bits */ +#define D64_RC_AE_SHIFT 16 + +/* flags for dma controller */ +#define DMA_CTRL_PEN (1 << 0) /* partity enable */ +#define DMA_CTRL_ROC (1 << 1) /* rx overflow continue */ +#define DMA_CTRL_RXMULTI (1 << 2) /* allow rx scatter to multiple descriptors */ +#define DMA_CTRL_UNFRAMED (1 << 3) /* Unframed Rx/Tx data */ + +/* receive descriptor table pointer */ +#define D64_RP_LD_MASK 0x00000fff /* last valid descriptor */ + +/* receive channel status */ +#define D64_RS0_CD_MASK 0x00001fff /* current descriptor pointer */ +#define D64_RS0_RS_MASK 0xf0000000 /* receive state */ +#define D64_RS0_RS_SHIFT 28 +#define D64_RS0_RS_DISABLED 0x00000000 /* disabled */ +#define D64_RS0_RS_ACTIVE 0x10000000 /* active */ +#define D64_RS0_RS_IDLE 0x20000000 /* idle wait */ +#define D64_RS0_RS_STOPPED 0x30000000 /* stopped */ +#define D64_RS0_RS_SUSP 0x40000000 /* suspend pending */ + +#define D64_RS1_AD_MASK 0x0001ffff /* active descriptor */ +#define D64_RS1_RE_MASK 0xf0000000 /* receive errors */ +#define D64_RS1_RE_SHIFT 28 +#define D64_RS1_RE_NOERR 0x00000000 /* no error */ +#define D64_RS1_RE_DPO 0x10000000 /* descriptor protocol error */ +#define D64_RS1_RE_DFU 0x20000000 /* data fifo overflow */ +#define D64_RS1_RE_DTE 0x30000000 /* data transfer error */ +#define D64_RS1_RE_DESRE 0x40000000 /* descriptor read error */ +#define D64_RS1_RE_COREE 0x50000000 /* core error */ + +/* fifoaddr */ +#define D64_FA_OFF_MASK 0xffff /* offset */ +#define D64_FA_SEL_MASK 0xf0000 /* select */ +#define D64_FA_SEL_SHIFT 16 +#define D64_FA_SEL_XDD 0x00000 /* transmit dma data */ +#define D64_FA_SEL_XDP 0x10000 /* transmit dma pointers */ +#define D64_FA_SEL_RDD 0x40000 /* receive dma data */ +#define D64_FA_SEL_RDP 0x50000 /* receive dma pointers */ +#define D64_FA_SEL_XFD 0x80000 /* transmit fifo data */ +#define D64_FA_SEL_XFP 0x90000 /* transmit fifo pointers */ +#define D64_FA_SEL_RFD 0xc0000 /* receive fifo data */ +#define D64_FA_SEL_RFP 0xd0000 /* receive fifo pointers */ +#define D64_FA_SEL_RSD 0xe0000 /* receive frame status data */ +#define D64_FA_SEL_RSP 0xf0000 /* receive frame status pointers */ + +/* descriptor control flags 1 */ +#define D64_CTRL_COREFLAGS 0x0ff00000 /* core specific flags */ +#define D64_CTRL1_EOT ((u32)1 << 28) /* end of descriptor table */ +#define D64_CTRL1_IOC ((u32)1 << 29) /* interrupt on completion */ +#define D64_CTRL1_EOF ((u32)1 << 30) /* end of frame */ +#define D64_CTRL1_SOF ((u32)1 << 31) /* start of frame */ + +/* descriptor control flags 2 */ +#define D64_CTRL2_BC_MASK 0x00007fff /* buffer byte count. real data len must <= 16KB */ +#define D64_CTRL2_AE 0x00030000 /* address extension bits */ +#define D64_CTRL2_AE_SHIFT 16 +#define D64_CTRL2_PARITY 0x00040000 /* parity bit */ + +/* control flags in the range [27:20] are core-specific and not defined here */ +#define D64_CTRL_CORE_MASK 0x0ff00000 + +#define D64_RX_FRM_STS_LEN 0x0000ffff /* frame length mask */ +#define D64_RX_FRM_STS_OVFL 0x00800000 /* RxOverFlow */ +#define D64_RX_FRM_STS_DSCRCNT 0x0f000000 /* no. of descriptors used - 1 */ +#define D64_RX_FRM_STS_DATATYPE 0xf0000000 /* core-dependent data type */ + /* debug/trace */ #ifdef BCMDBG #define DMA_ERROR(args) \ @@ -69,6 +186,17 @@ static uint dma_msg_level; #define R_SM(r) (*(r)) #define W_SM(r, v) (*(r) = (v)) +/* + * DMA Descriptor + * Descriptors are only read by the hardware, never written back. + */ +typedef volatile struct { + u32 ctrl1; /* misc control bits & bufcount */ + u32 ctrl2; /* buffer count and address extension */ + u32 addrlow; /* memory address of the date buffer, bits 31:0 */ + u32 addrhigh; /* memory address of the date buffer, bits 63:32 */ +} dma64dd_t; + /* dma engine software state */ typedef struct dma_info { struct dma_pub dma; /* exported structure */ diff --git a/drivers/staging/brcm80211/brcmsmac/nicpci.c b/drivers/staging/brcm80211/brcmsmac/nicpci.c index 51d56b6b63d5..806b2ca0a8c9 100644 --- a/drivers/staging/brcm80211/brcmsmac/nicpci.c +++ b/drivers/staging/brcm80211/brcmsmac/nicpci.c @@ -29,6 +29,9 @@ #include #include +/* chipcontrol */ +#define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */ + typedef struct { union { sbpcieregs_t *pcieregs; diff --git a/drivers/staging/brcm80211/brcmsmac/phy/wlc_phy_n.c b/drivers/staging/brcm80211/brcmsmac/phy/wlc_phy_n.c index 123bd6ae47d7..620eb86f1fe3 100644 --- a/drivers/staging/brcm80211/brcmsmac/phy/wlc_phy_n.c +++ b/drivers/staging/brcm80211/brcmsmac/phy/wlc_phy_n.c @@ -141,6 +141,10 @@ #define NPHY_ADJUSTED_MINCRSPOWER 0x1e +/* 5357 Chip specific ChipControl register bits */ +#define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */ +#define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */ + typedef struct _nphy_iqcal_params { u16 txlpf; u16 txgm; diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c b/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c index ab4ef6c2a11d..a7994e4031f4 100644 --- a/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c +++ b/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c @@ -29,7 +29,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_phy_shim.c b/drivers/staging/brcm80211/brcmsmac/wlc_phy_shim.c index c6f9694d31aa..7bb122b7c786 100644 --- a/drivers/staging/brcm80211/brcmsmac/wlc_phy_shim.c +++ b/drivers/staging/brcm80211/brcmsmac/wlc_phy_shim.c @@ -29,7 +29,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_pmu.c b/drivers/staging/brcm80211/brcmsmac/wlc_pmu.c index 82986bd1ccfa..e9230a883ad8 100644 --- a/drivers/staging/brcm80211/brcmsmac/wlc_pmu.c +++ b/drivers/staging/brcm80211/brcmsmac/wlc_pmu.c @@ -128,9 +128,474 @@ #define RES_DEPEND_ADD 1 #define RES_DEPEND_REMOVE -1 +/* Fields in pmucontrol */ +#define PCTL_ILP_DIV_MASK 0xffff0000 +#define PCTL_ILP_DIV_SHIFT 16 +#define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */ +#define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */ +#define PCTL_HT_REQ_EN 0x00000100 +#define PCTL_ALP_REQ_EN 0x00000080 +#define PCTL_XTALFREQ_MASK 0x0000007c +#define PCTL_XTALFREQ_SHIFT 2 +#define PCTL_ILP_DIV_EN 0x00000002 +#define PCTL_LPO_SEL 0x00000001 + +/* Fields in clkstretch */ +#define CSTRETCH_HT 0xffff0000 +#define CSTRETCH_ALP 0x0000ffff + /* d11 slow to fast clock transition time in slow clock cycles */ #define D11SCC_SLOW2FAST_TRANSITION 2 +/* ILP clock */ +#define ILP_CLOCK 32000 + +/* ALP clock on pre-PMU chips */ +#define ALP_CLOCK 20000000 + +/* HT clock */ +#define HT_CLOCK 80000000 + +#define OTPS_READY 0x00001000 + +/* pmustatus */ +#define PST_EXTLPOAVAIL 0x0100 +#define PST_WDRESET 0x0080 +#define PST_INTPEND 0x0040 +#define PST_SBCLKST 0x0030 +#define PST_SBCLKST_ILP 0x0010 +#define PST_SBCLKST_ALP 0x0020 +#define PST_SBCLKST_HT 0x0030 +#define PST_ALPAVAIL 0x0008 +#define PST_HTAVAIL 0x0004 +#define PST_RESINIT 0x0003 + +/* PMU Resource Request Timer registers */ +/* This is based on PmuRev0 */ +#define PRRT_TIME_MASK 0x03ff +#define PRRT_INTEN 0x0400 +#define PRRT_REQ_ACTIVE 0x0800 +#define PRRT_ALP_REQ 0x1000 +#define PRRT_HT_REQ 0x2000 + +/* PMU resource bit position */ +#define PMURES_BIT(bit) (1 << (bit)) + +/* PMU resource number limit */ +#define PMURES_MAX_RESNUM 30 + +/* PMU chip control0 register */ +#define PMU_CHIPCTL0 0 + +/* PMU chip control1 register */ +#define PMU_CHIPCTL1 1 +#define PMU_CC1_RXC_DLL_BYPASS 0x00010000 + +#define PMU_CC1_IF_TYPE_MASK 0x00000030 +#define PMU_CC1_IF_TYPE_RMII 0x00000000 +#define PMU_CC1_IF_TYPE_MII 0x00000010 +#define PMU_CC1_IF_TYPE_RGMII 0x00000020 + +#define PMU_CC1_SW_TYPE_MASK 0x000000c0 +#define PMU_CC1_SW_TYPE_EPHY 0x00000000 +#define PMU_CC1_SW_TYPE_EPHYMII 0x00000040 +#define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080 +#define PMU_CC1_SW_TYPE_RGMII 0x000000c0 + +/* PMU corerev and chip specific PLL controls. + * PMU_PLL_XX where is PMU corerev and is an arbitrary number + * to differentiate different PLLs controlled by the same PMU rev. + */ +/* pllcontrol registers */ +/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */ +#define PMU0_PLL0_PLLCTL0 0 +#define PMU0_PLL0_PC0_PDIV_MASK 1 +#define PMU0_PLL0_PC0_PDIV_FREQ 25000 +#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038 +#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3 +#define PMU0_PLL0_PC0_DIV_ARM_BASE 8 + +/* PC0_DIV_ARM for PLLOUT_ARM */ +#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0 +#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1 +#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2 +#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */ +#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4 +#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5 +#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6 +#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7 + +/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */ +#define PMU0_PLL0_PLLCTL1 1 +#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000 +#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28 +#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00 +#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8 +#define PMU0_PLL0_PC1_STOP_MOD 0x00000040 + +/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */ +#define PMU0_PLL0_PLLCTL2 2 +#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf +#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4 + +/* pllcontrol registers */ +/* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ +#define PMU1_PLL0_PLLCTL0 0 +#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000 +#define PMU1_PLL0_PC0_P1DIV_SHIFT 20 +#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000 +#define PMU1_PLL0_PC0_P2DIV_SHIFT 24 + +/* mdiv */ +#define PMU1_PLL0_PLLCTL1 1 +#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff +#define PMU1_PLL0_PC1_M1DIV_SHIFT 0 +#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00 +#define PMU1_PLL0_PC1_M2DIV_SHIFT 8 +#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000 +#define PMU1_PLL0_PC1_M3DIV_SHIFT 16 +#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000 +#define PMU1_PLL0_PC1_M4DIV_SHIFT 24 + +#define PMU1_PLL0_CHIPCTL0 0 +#define PMU1_PLL0_CHIPCTL1 1 +#define PMU1_PLL0_CHIPCTL2 2 + +#define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8 +#define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) +#define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) + +/* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ +#define PMU1_PLL0_PLLCTL2 2 +#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff +#define PMU1_PLL0_PC2_M5DIV_SHIFT 0 +#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00 +#define PMU1_PLL0_PC2_M6DIV_SHIFT 8 +#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000 +#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17 +#define PMU1_PLL0_PC2_NDIV_MODE_MASH 1 +#define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */ +#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000 +#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20 + +/* ndiv_frac */ +#define PMU1_PLL0_PLLCTL3 3 +#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff +#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0 + +/* pll_ctrl */ +#define PMU1_PLL0_PLLCTL4 4 + +/* pll_ctrl, vco_rng, clkdrive_ch */ +#define PMU1_PLL0_PLLCTL5 5 +#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00 +#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8 + +/* PMU rev 2 control words */ +#define PMU2_PHY_PLL_PLLCTL 4 +#define PMU2_SI_PLL_PLLCTL 10 + +/* PMU rev 2 */ +/* pllcontrol registers */ +/* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ +#define PMU2_PLL_PLLCTL0 0 +#define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000 +#define PMU2_PLL_PC0_P1DIV_SHIFT 20 +#define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000 +#define PMU2_PLL_PC0_P2DIV_SHIFT 24 + +/* mdiv */ +#define PMU2_PLL_PLLCTL1 1 +#define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff +#define PMU2_PLL_PC1_M1DIV_SHIFT 0 +#define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00 +#define PMU2_PLL_PC1_M2DIV_SHIFT 8 +#define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000 +#define PMU2_PLL_PC1_M3DIV_SHIFT 16 +#define PMU2_PLL_PC1_M4DIV_MASK 0xff000000 +#define PMU2_PLL_PC1_M4DIV_SHIFT 24 + +/* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ +#define PMU2_PLL_PLLCTL2 2 +#define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff +#define PMU2_PLL_PC2_M5DIV_SHIFT 0 +#define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00 +#define PMU2_PLL_PC2_M6DIV_SHIFT 8 +#define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000 +#define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17 +#define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000 +#define PMU2_PLL_PC2_NDIV_INT_SHIFT 20 + +/* ndiv_frac */ +#define PMU2_PLL_PLLCTL3 3 +#define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff +#define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0 + +/* pll_ctrl */ +#define PMU2_PLL_PLLCTL4 4 + +/* pll_ctrl, vco_rng, clkdrive_ch */ +#define PMU2_PLL_PLLCTL5 5 +#define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00 +#define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8 +#define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000 +#define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12 +#define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000 +#define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16 +#define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000 +#define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20 +#define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000 +#define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24 +#define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000 +#define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28 + +/* PMU rev 5 (& 6) */ +#define PMU5_PLL_P1P2_OFF 0 +#define PMU5_PLL_P1_MASK 0x0f000000 +#define PMU5_PLL_P1_SHIFT 24 +#define PMU5_PLL_P2_MASK 0x00f00000 +#define PMU5_PLL_P2_SHIFT 20 +#define PMU5_PLL_M14_OFF 1 +#define PMU5_PLL_MDIV_MASK 0x000000ff +#define PMU5_PLL_MDIV_WIDTH 8 +#define PMU5_PLL_NM5_OFF 2 +#define PMU5_PLL_NDIV_MASK 0xfff00000 +#define PMU5_PLL_NDIV_SHIFT 20 +#define PMU5_PLL_NDIV_MODE_MASK 0x000e0000 +#define PMU5_PLL_NDIV_MODE_SHIFT 17 +#define PMU5_PLL_FMAB_OFF 3 +#define PMU5_PLL_MRAT_MASK 0xf0000000 +#define PMU5_PLL_MRAT_SHIFT 28 +#define PMU5_PLL_ABRAT_MASK 0x08000000 +#define PMU5_PLL_ABRAT_SHIFT 27 +#define PMU5_PLL_FDIV_MASK 0x07ffffff +#define PMU5_PLL_PLLCTL_OFF 4 +#define PMU5_PLL_PCHI_OFF 5 +#define PMU5_PLL_PCHI_MASK 0x0000003f + +/* pmu XtalFreqRatio */ +#define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF +#define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000 +#define PMU_XTALFREQ_REG_MEASURE_SHIFT 31 + +/* Divider allocation in 4716/47162/5356/5357 */ +#define PMU5_MAINPLL_CPU 1 +#define PMU5_MAINPLL_MEM 2 +#define PMU5_MAINPLL_SI 3 + +#define PMU7_PLL_PLLCTL7 7 +#define PMU7_PLL_PLLCTL8 8 +#define PMU7_PLL_PLLCTL11 11 + +/* PLL usage in 4716/47162 */ +#define PMU4716_MAINPLL_PLL0 12 + +/* PLL usage in 5356/5357 */ +#define PMU5356_MAINPLL_PLL0 0 +#define PMU5357_MAINPLL_PLL0 0 + +/* 4328 resources */ +#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */ +#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */ +#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */ +#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */ +#define RES4328_ILP_REQUEST 4 /* 0x00010 */ +#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */ +#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */ +#define RES4328_ROM_SWITCH 7 /* 0x00080 */ +#define RES4328_PA_REF_LDO 8 /* 0x00100 */ +#define RES4328_RADIO_LDO 9 /* 0x00200 */ +#define RES4328_AFE_LDO 10 /* 0x00400 */ +#define RES4328_PLL_LDO 11 /* 0x00800 */ +#define RES4328_BG_FILTBYP 12 /* 0x01000 */ +#define RES4328_TX_FILTBYP 13 /* 0x02000 */ +#define RES4328_RX_FILTBYP 14 /* 0x04000 */ +#define RES4328_XTAL_PU 15 /* 0x08000 */ +#define RES4328_XTAL_EN 16 /* 0x10000 */ +#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */ +#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */ +#define RES4328_BB_PLL_PU 19 /* 0x80000 */ + +/* 4325 A0/A1 resources */ +#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */ +#define RES4325_CBUCK_BURST 1 /* 0x00000002 */ +#define RES4325_CBUCK_PWM 2 /* 0x00000004 */ +#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */ +#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */ +#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */ +#define RES4325_ILP_REQUEST 6 /* 0x00000040 */ +#define RES4325_ABUCK_BURST 7 /* 0x00000080 */ +#define RES4325_ABUCK_PWM 8 /* 0x00000100 */ +#define RES4325_LNLDO1_PU 9 /* 0x00000200 */ +#define RES4325_OTP_PU 10 /* 0x00000400 */ +#define RES4325_LNLDO3_PU 11 /* 0x00000800 */ +#define RES4325_LNLDO4_PU 12 /* 0x00001000 */ +#define RES4325_XTAL_PU 13 /* 0x00002000 */ +#define RES4325_ALP_AVAIL 14 /* 0x00004000 */ +#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */ +#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */ +#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */ +#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */ +#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */ +#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */ +#define RES4325_HT_AVAIL 21 /* 0x00200000 */ + +/* 4325 B0/C0 resources */ +#define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */ +#define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */ +#define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */ +#define RES4325B0_CLDO_PU 4 /* 0x00000010 */ + +/* 4325 C1 resources */ +#define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */ + +#define RES4329_RESERVED0 0 /* 0x00000001 */ +#define RES4329_CBUCK_LPOM 1 /* 0x00000002 */ +#define RES4329_CBUCK_BURST 2 /* 0x00000004 */ +#define RES4329_CBUCK_PWM 3 /* 0x00000008 */ +#define RES4329_CLDO_PU 4 /* 0x00000010 */ +#define RES4329_PALDO_PU 5 /* 0x00000020 */ +#define RES4329_ILP_REQUEST 6 /* 0x00000040 */ +#define RES4329_RESERVED7 7 /* 0x00000080 */ +#define RES4329_RESERVED8 8 /* 0x00000100 */ +#define RES4329_LNLDO1_PU 9 /* 0x00000200 */ +#define RES4329_OTP_PU 10 /* 0x00000400 */ +#define RES4329_RESERVED11 11 /* 0x00000800 */ +#define RES4329_LNLDO2_PU 12 /* 0x00001000 */ +#define RES4329_XTAL_PU 13 /* 0x00002000 */ +#define RES4329_ALP_AVAIL 14 /* 0x00004000 */ +#define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */ +#define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */ +#define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */ +#define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */ +#define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */ +#define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */ +#define RES4329_HT_AVAIL 21 /* 0x00200000 */ + +/* 4315 resources */ +#define RES4315_CBUCK_LPOM 1 /* 0x00000002 */ +#define RES4315_CBUCK_BURST 2 /* 0x00000004 */ +#define RES4315_CBUCK_PWM 3 /* 0x00000008 */ +#define RES4315_CLDO_PU 4 /* 0x00000010 */ +#define RES4315_PALDO_PU 5 /* 0x00000020 */ +#define RES4315_ILP_REQUEST 6 /* 0x00000040 */ +#define RES4315_LNLDO1_PU 9 /* 0x00000200 */ +#define RES4315_OTP_PU 10 /* 0x00000400 */ +#define RES4315_LNLDO2_PU 12 /* 0x00001000 */ +#define RES4315_XTAL_PU 13 /* 0x00002000 */ +#define RES4315_ALP_AVAIL 14 /* 0x00004000 */ +#define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */ +#define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */ +#define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */ +#define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */ +#define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */ +#define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */ +#define RES4315_HT_AVAIL 21 /* 0x00200000 */ + +/* 4319 resources */ +#define RES4319_CBUCK_LPOM 1 /* 0x00000002 */ +#define RES4319_CBUCK_BURST 2 /* 0x00000004 */ +#define RES4319_CBUCK_PWM 3 /* 0x00000008 */ +#define RES4319_CLDO_PU 4 /* 0x00000010 */ +#define RES4319_PALDO_PU 5 /* 0x00000020 */ +#define RES4319_ILP_REQUEST 6 /* 0x00000040 */ +#define RES4319_LNLDO1_PU 9 /* 0x00000200 */ +#define RES4319_OTP_PU 10 /* 0x00000400 */ +#define RES4319_LNLDO2_PU 12 /* 0x00001000 */ +#define RES4319_XTAL_PU 13 /* 0x00002000 */ +#define RES4319_ALP_AVAIL 14 /* 0x00004000 */ +#define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */ +#define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */ +#define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */ +#define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */ +#define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */ +#define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */ +#define RES4319_HT_AVAIL 21 /* 0x00200000 */ + +#define CCTL_4319USB_XTAL_SEL_MASK 0x00180000 +#define CCTL_4319USB_XTAL_SEL_SHIFT 19 +#define CCTL_4319USB_48MHZ_PLL_SEL 1 +#define CCTL_4319USB_24MHZ_PLL_SEL 2 + +/* PMU resources for 4336 */ +#define RES4336_CBUCK_LPOM 0 +#define RES4336_CBUCK_BURST 1 +#define RES4336_CBUCK_LP_PWM 2 +#define RES4336_CBUCK_PWM 3 +#define RES4336_CLDO_PU 4 +#define RES4336_DIS_INT_RESET_PD 5 +#define RES4336_ILP_REQUEST 6 +#define RES4336_LNLDO_PU 7 +#define RES4336_LDO3P3_PU 8 +#define RES4336_OTP_PU 9 +#define RES4336_XTAL_PU 10 +#define RES4336_ALP_AVAIL 11 +#define RES4336_RADIO_PU 12 +#define RES4336_BG_PU 13 +#define RES4336_VREG1p4_PU_PU 14 +#define RES4336_AFE_PWRSW_PU 15 +#define RES4336_RX_PWRSW_PU 16 +#define RES4336_TX_PWRSW_PU 17 +#define RES4336_BB_PWRSW_PU 18 +#define RES4336_SYNTH_PWRSW_PU 19 +#define RES4336_MISC_PWRSW_PU 20 +#define RES4336_LOGEN_PWRSW_PU 21 +#define RES4336_BBPLL_PWRSW_PU 22 +#define RES4336_MACPHY_CLKAVAIL 23 +#define RES4336_HT_AVAIL 24 +#define RES4336_RSVD 25 + +/* 4330 resources */ +#define RES4330_CBUCK_LPOM 0 +#define RES4330_CBUCK_BURST 1 +#define RES4330_CBUCK_LP_PWM 2 +#define RES4330_CBUCK_PWM 3 +#define RES4330_CLDO_PU 4 +#define RES4330_DIS_INT_RESET_PD 5 +#define RES4330_ILP_REQUEST 6 +#define RES4330_LNLDO_PU 7 +#define RES4330_LDO3P3_PU 8 +#define RES4330_OTP_PU 9 +#define RES4330_XTAL_PU 10 +#define RES4330_ALP_AVAIL 11 +#define RES4330_RADIO_PU 12 +#define RES4330_BG_PU 13 +#define RES4330_VREG1p4_PU_PU 14 +#define RES4330_AFE_PWRSW_PU 15 +#define RES4330_RX_PWRSW_PU 16 +#define RES4330_TX_PWRSW_PU 17 +#define RES4330_BB_PWRSW_PU 18 +#define RES4330_SYNTH_PWRSW_PU 19 +#define RES4330_MISC_PWRSW_PU 20 +#define RES4330_LOGEN_PWRSW_PU 21 +#define RES4330_BBPLL_PWRSW_PU 22 +#define RES4330_MACPHY_CLKAVAIL 23 +#define RES4330_HT_AVAIL 24 +#define RES4330_5gRX_PWRSW_PU 25 +#define RES4330_5gTX_PWRSW_PU 26 +#define RES4330_5g_LOGEN_PWRSW_PU 27 + +/* 4313 resources */ +#define RES4313_BB_PU_RSRC 0 +#define RES4313_ILP_REQ_RSRC 1 +#define RES4313_XTAL_PU_RSRC 2 +#define RES4313_ALP_AVAIL_RSRC 3 +#define RES4313_RADIO_PU_RSRC 4 +#define RES4313_BG_PU_RSRC 5 +#define RES4313_VREG1P4_PU_RSRC 6 +#define RES4313_AFE_PWRSW_RSRC 7 +#define RES4313_RX_PWRSW_RSRC 8 +#define RES4313_TX_PWRSW_RSRC 9 +#define RES4313_BB_PWRSW_RSRC 10 +#define RES4313_SYNTH_PWRSW_RSRC 11 +#define RES4313_MISC_PWRSW_RSRC 12 +#define RES4313_BB_PLL_PWRSW_RSRC 13 +#define RES4313_HT_AVAIL_RSRC 14 +#define RES4313_MACPHY_CLK_AVAIL_RSRC 15 + +/* PMU resource up transition time in ILP cycles */ +#define PMURES_UP_TRANSITION 2 + /* Setup resource up/down timers */ typedef struct { u8 resnum; diff --git a/drivers/staging/brcm80211/include/sbchipc.h b/drivers/staging/brcm80211/include/sbchipc.h index 8c01c638ab8d..9ca2e691caad 100644 --- a/drivers/staging/brcm80211/include/sbchipc.h +++ b/drivers/staging/brcm80211/include/sbchipc.h @@ -17,8 +17,6 @@ #ifndef _SBCHIPC_H #define _SBCHIPC_H -#ifndef _LANGUAGE_ASSEMBLY - /* cpp contortions to concatenate w/arg prescan */ #ifndef PAD #define _PADLINE(line) pad ## line @@ -223,63 +221,6 @@ typedef volatile struct { u16 sromotp[768]; } chipcregs_t; -#endif /* _LANGUAGE_ASSEMBLY */ - -#if defined(__BIG_ENDIAN) && defined(BCMHND74K) -/* Selective swapped defines for those registers we need in - * big-endian code. - */ -#define CC_CHIPID 4 -#define CC_CAPABILITIES 0 -#define CC_CHIPST 0x28 -#define CC_EROMPTR 0xf8 - -#else /* !__BIG_ENDIAN || !BCMHND74K */ - -#define CC_CHIPID 0 -#define CC_CAPABILITIES 4 -#define CC_CHIPST 0x2c -#define CC_EROMPTR 0xfc - -#endif /* __BIG_ENDIAN && BCMHND74K */ - -#define CC_OTPST 0x10 -#define CC_JTAGCMD 0x30 -#define CC_JTAGIR 0x34 -#define CC_JTAGDR 0x38 -#define CC_JTAGCTRL 0x3c -#define CC_GPIOPU 0x58 -#define CC_GPIOPD 0x5c -#define CC_GPIOIN 0x60 -#define CC_GPIOOUT 0x64 -#define CC_GPIOOUTEN 0x68 -#define CC_GPIOCTRL 0x6c -#define CC_GPIOPOL 0x70 -#define CC_GPIOINTM 0x74 -#define CC_WATCHDOG 0x80 -#define CC_CLKC_N 0x90 -#define CC_CLKC_M0 0x94 -#define CC_CLKC_M1 0x98 -#define CC_CLKC_M2 0x9c -#define CC_CLKC_M3 0xa0 -#define CC_CLKDIV 0xa4 -#define CC_SYS_CLK_CTL 0xc0 -#define CC_CLK_CTL_ST SI_CLK_CTL_ST -#define PMU_CTL 0x600 -#define PMU_CAP 0x604 -#define PMU_ST 0x608 -#define PMU_RES_STATE 0x60c -#define PMU_TIMER 0x614 -#define PMU_MIN_RES_MASK 0x618 -#define PMU_MAX_RES_MASK 0x61c -#define CC_CHIPCTL_ADDR 0x650 -#define CC_CHIPCTL_DATA 0x654 -#define PMU_REG_CONTROL_ADDR 0x658 -#define PMU_REG_CONTROL_DATA 0x65C -#define PMU_PLL_CONTROL_ADDR 0x660 -#define PMU_PLL_CONTROL_DATA 0x664 -#define CC_SROM_OTP 0x800 /* SROM/OTP address space */ - /* chipid */ #define CID_ID_MASK 0x0000ffff /* Chip Id mask */ #define CID_REV_MASK 0x000f0000 /* Chip Revision mask */ @@ -317,504 +258,6 @@ typedef volatile struct { #define CC_CAP2_SECI 0x00000001 /* SECI Present, rev >= 36 */ #define CC_CAP2_GSIO 0x00000002 /* GSIO (spi/i2c) present, rev >= 37 */ -/* PLL type */ -#define PLL_NONE 0x00000000 -#define PLL_TYPE1 0x00010000 /* 48MHz base, 3 dividers */ -#define PLL_TYPE2 0x00020000 /* 48MHz, 4 dividers */ -#define PLL_TYPE3 0x00030000 /* 25MHz, 2 dividers */ -#define PLL_TYPE4 0x00008000 /* 48MHz, 4 dividers */ -#define PLL_TYPE5 0x00018000 /* 25MHz, 4 dividers */ -#define PLL_TYPE6 0x00028000 /* 100/200 or 120/240 only */ -#define PLL_TYPE7 0x00038000 /* 25MHz, 4 dividers */ - -/* ILP clock */ -#define ILP_CLOCK 32000 - -/* ALP clock on pre-PMU chips */ -#define ALP_CLOCK 20000000 - -/* HT clock */ -#define HT_CLOCK 80000000 - -/* corecontrol */ -#define CC_UARTCLKO 0x00000001 /* Drive UART with internal clock */ -#define CC_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ -#define CC_UARTCLKEN 0x00000008 /* enable UART Clock (corerev > = 21 */ - -/* chipcontrol */ -#define CHIPCTRL_4321A0_DEFAULT 0x3a4 -#define CHIPCTRL_4321A1_DEFAULT 0x0a4 -#define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */ - -/* Fields in the otpstatus register in rev >= 21 */ -#define OTPS_OL_MASK 0x000000ff -#define OTPS_OL_MFG 0x00000001 /* manuf row is locked */ -#define OTPS_OL_OR1 0x00000002 /* otp redundancy row 1 is locked */ -#define OTPS_OL_OR2 0x00000004 /* otp redundancy row 2 is locked */ -#define OTPS_OL_GU 0x00000008 /* general use region is locked */ -#define OTPS_GUP_MASK 0x00000f00 -#define OTPS_GUP_SHIFT 8 -#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */ -#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */ -#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */ -#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */ -#define OTPS_READY 0x00001000 -#define OTPS_RV(x) (1 << (16 + (x))) /* redundancy entry valid */ -#define OTPS_RV_MASK 0x0fff0000 - -/* Fields in the otpcontrol register in rev >= 21 */ -#define OTPC_PROGSEL 0x00000001 -#define OTPC_PCOUNT_MASK 0x0000000e -#define OTPC_PCOUNT_SHIFT 1 -#define OTPC_VSEL_MASK 0x000000f0 -#define OTPC_VSEL_SHIFT 4 -#define OTPC_TMM_MASK 0x00000700 -#define OTPC_TMM_SHIFT 8 -#define OTPC_ODM 0x00000800 -#define OTPC_PROGEN 0x80000000 - -/* Fields in otpprog in rev >= 21 and HND OTP */ -#define OTPP_COL_MASK 0x000000ff -#define OTPP_COL_SHIFT 0 -#define OTPP_ROW_MASK 0x0000ff00 -#define OTPP_ROW_SHIFT 8 -#define OTPP_OC_MASK 0x0f000000 -#define OTPP_OC_SHIFT 24 -#define OTPP_READERR 0x10000000 -#define OTPP_VALUE_MASK 0x20000000 -#define OTPP_VALUE_SHIFT 29 -#define OTPP_START_BUSY 0x80000000 -#define OTPP_READ 0x40000000 /* HND OTP */ - -/* otplayout reg corerev >= 36 */ -#define OTP_CISFORMAT_NEW 0x80000000 - -/* Opcodes for OTPP_OC field */ -#define OTPPOC_READ 0 -#define OTPPOC_BIT_PROG 1 -#define OTPPOC_VERIFY 3 -#define OTPPOC_INIT 4 -#define OTPPOC_SET 5 -#define OTPPOC_RESET 6 -#define OTPPOC_OCST 7 -#define OTPPOC_ROW_LOCK 8 -#define OTPPOC_PRESCN_TEST 9 - -/* Jtagm characteristics that appeared at a given corerev */ -#define JTAGM_CREV_OLD 10 /* Old command set, 16bit max IR */ -#define JTAGM_CREV_IRP 22 /* Able to do pause-ir */ -#define JTAGM_CREV_RTI 28 /* Able to do return-to-idle */ - -/* jtagcmd */ -#define JCMD_START 0x80000000 -#define JCMD_BUSY 0x80000000 -#define JCMD_STATE_MASK 0x60000000 -#define JCMD_STATE_TLR 0x00000000 /* Test-logic-reset */ -#define JCMD_STATE_PIR 0x20000000 /* Pause IR */ -#define JCMD_STATE_PDR 0x40000000 /* Pause DR */ -#define JCMD_STATE_RTI 0x60000000 /* Run-test-idle */ -#define JCMD0_ACC_MASK 0x0000f000 -#define JCMD0_ACC_IRDR 0x00000000 -#define JCMD0_ACC_DR 0x00001000 -#define JCMD0_ACC_IR 0x00002000 -#define JCMD0_ACC_RESET 0x00003000 -#define JCMD0_ACC_IRPDR 0x00004000 -#define JCMD0_ACC_PDR 0x00005000 -#define JCMD0_IRW_MASK 0x00000f00 -#define JCMD_ACC_MASK 0x000f0000 /* Changes for corerev 11 */ -#define JCMD_ACC_IRDR 0x00000000 -#define JCMD_ACC_DR 0x00010000 -#define JCMD_ACC_IR 0x00020000 -#define JCMD_ACC_RESET 0x00030000 -#define JCMD_ACC_IRPDR 0x00040000 -#define JCMD_ACC_PDR 0x00050000 -#define JCMD_ACC_PIR 0x00060000 -#define JCMD_ACC_IRDR_I 0x00070000 /* rev 28: return to run-test-idle */ -#define JCMD_ACC_DR_I 0x00080000 /* rev 28: return to run-test-idle */ -#define JCMD_IRW_MASK 0x00001f00 -#define JCMD_IRW_SHIFT 8 -#define JCMD_DRW_MASK 0x0000003f - -/* jtagctrl */ -#define JCTRL_FORCE_CLK 4 /* Force clock */ -#define JCTRL_EXT_EN 2 /* Enable external targets */ -#define JCTRL_EN 1 /* Enable Jtag master */ - -/* Fields in clkdiv */ -#define CLKD_SFLASH 0x0f000000 -#define CLKD_SFLASH_SHIFT 24 -#define CLKD_OTP 0x000f0000 -#define CLKD_OTP_SHIFT 16 -#define CLKD_JTAG 0x00000f00 -#define CLKD_JTAG_SHIFT 8 -#define CLKD_UART 0x000000ff - -#define CLKD2_SROM 0x00000003 - -/* intstatus/intmask */ -#define CI_GPIO 0x00000001 /* gpio intr */ -#define CI_EI 0x00000002 /* extif intr (corerev >= 3) */ -#define CI_TEMP 0x00000004 /* temp. ctrl intr (corerev >= 15) */ -#define CI_SIRQ 0x00000008 /* serial IRQ intr (corerev >= 15) */ -#define CI_PMU 0x00000020 /* pmu intr (corerev >= 21) */ -#define CI_UART 0x00000040 /* uart intr (corerev >= 21) */ -#define CI_WDRESET 0x80000000 /* watchdog reset occurred */ - -/* slow_clk_ctl */ -#define SCC_SS_MASK 0x00000007 /* slow clock source mask */ -#define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */ -#define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */ -#define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */ -#define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ -#define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled, - * 0: LPO is enabled - */ -#define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, - * 0: power logic control - */ -#define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors - * PLL clock disable requests from core - */ -#define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't - * disable crystal when appropriate - */ -#define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ -#define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ -#define SCC_CD_SHIFT 16 - -/* system_clk_ctl */ -#define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */ -#define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */ -#define SYCC_FP 0x00000004 /* ForcePLLOn */ -#define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */ -#define SYCC_HR 0x00000010 /* Force HT */ -#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */ -#define SYCC_CD_SHIFT 16 - -/* Indirect backplane access */ -#define BPIA_BYTEEN 0x0000000f -#define BPIA_SZ1 0x00000001 -#define BPIA_SZ2 0x00000003 -#define BPIA_SZ4 0x00000007 -#define BPIA_SZ8 0x0000000f -#define BPIA_WRITE 0x00000100 -#define BPIA_START 0x00000200 -#define BPIA_BUSY 0x00000200 -#define BPIA_ERROR 0x00000400 - -/* pcmcia/prog/flash_config */ -#define CF_EN 0x00000001 /* enable */ -#define CF_EM_MASK 0x0000000e /* mode */ -#define CF_EM_SHIFT 1 -#define CF_EM_FLASH 0 /* flash/asynchronous mode */ -#define CF_EM_SYNC 2 /* synchronous mode */ -#define CF_EM_PCMCIA 4 /* pcmcia mode */ -#define CF_DS 0x00000010 /* destsize: 0=8bit, 1=16bit */ -#define CF_BS 0x00000020 /* byteswap */ -#define CF_CD_MASK 0x000000c0 /* clock divider */ -#define CF_CD_SHIFT 6 -#define CF_CD_DIV2 0x00000000 /* backplane/2 */ -#define CF_CD_DIV3 0x00000040 /* backplane/3 */ -#define CF_CD_DIV4 0x00000080 /* backplane/4 */ -#define CF_CE 0x00000100 /* clock enable */ -#define CF_SB 0x00000200 /* size/bytestrobe (synch only) */ - -/* pcmcia_memwait */ -#define PM_W0_MASK 0x0000003f /* waitcount0 */ -#define PM_W1_MASK 0x00001f00 /* waitcount1 */ -#define PM_W1_SHIFT 8 -#define PM_W2_MASK 0x001f0000 /* waitcount2 */ -#define PM_W2_SHIFT 16 -#define PM_W3_MASK 0x1f000000 /* waitcount3 */ -#define PM_W3_SHIFT 24 - -/* pcmcia_attrwait */ -#define PA_W0_MASK 0x0000003f /* waitcount0 */ -#define PA_W1_MASK 0x00001f00 /* waitcount1 */ -#define PA_W1_SHIFT 8 -#define PA_W2_MASK 0x001f0000 /* waitcount2 */ -#define PA_W2_SHIFT 16 -#define PA_W3_MASK 0x1f000000 /* waitcount3 */ -#define PA_W3_SHIFT 24 - -/* pcmcia_iowait */ -#define PI_W0_MASK 0x0000003f /* waitcount0 */ -#define PI_W1_MASK 0x00001f00 /* waitcount1 */ -#define PI_W1_SHIFT 8 -#define PI_W2_MASK 0x001f0000 /* waitcount2 */ -#define PI_W2_SHIFT 16 -#define PI_W3_MASK 0x1f000000 /* waitcount3 */ -#define PI_W3_SHIFT 24 - -/* prog_waitcount */ -#define PW_W0_MASK 0x0000001f /* waitcount0 */ -#define PW_W1_MASK 0x00001f00 /* waitcount1 */ -#define PW_W1_SHIFT 8 -#define PW_W2_MASK 0x001f0000 /* waitcount2 */ -#define PW_W2_SHIFT 16 -#define PW_W3_MASK 0x1f000000 /* waitcount3 */ -#define PW_W3_SHIFT 24 - -#define PW_W0 0x0000000c -#define PW_W1 0x00000a00 -#define PW_W2 0x00020000 -#define PW_W3 0x01000000 - -/* flash_waitcount */ -#define FW_W0_MASK 0x0000003f /* waitcount0 */ -#define FW_W1_MASK 0x00001f00 /* waitcount1 */ -#define FW_W1_SHIFT 8 -#define FW_W2_MASK 0x001f0000 /* waitcount2 */ -#define FW_W2_SHIFT 16 -#define FW_W3_MASK 0x1f000000 /* waitcount3 */ -#define FW_W3_SHIFT 24 - -/* When Srom support present, fields in sromcontrol */ -#define SRC_START 0x80000000 -#define SRC_BUSY 0x80000000 -#define SRC_OPCODE 0x60000000 -#define SRC_OP_READ 0x00000000 -#define SRC_OP_WRITE 0x20000000 -#define SRC_OP_WRDIS 0x40000000 -#define SRC_OP_WREN 0x60000000 -#define SRC_OTPSEL 0x00000010 -#define SRC_LOCK 0x00000008 -#define SRC_SIZE_MASK 0x00000006 -#define SRC_SIZE_1K 0x00000000 -#define SRC_SIZE_4K 0x00000002 -#define SRC_SIZE_16K 0x00000004 -#define SRC_SIZE_SHIFT 1 -#define SRC_PRESENT 0x00000001 - -/* Fields in pmucontrol */ -#define PCTL_ILP_DIV_MASK 0xffff0000 -#define PCTL_ILP_DIV_SHIFT 16 -#define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */ -#define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */ -#define PCTL_HT_REQ_EN 0x00000100 -#define PCTL_ALP_REQ_EN 0x00000080 -#define PCTL_XTALFREQ_MASK 0x0000007c -#define PCTL_XTALFREQ_SHIFT 2 -#define PCTL_ILP_DIV_EN 0x00000002 -#define PCTL_LPO_SEL 0x00000001 - -/* Fields in clkstretch */ -#define CSTRETCH_HT 0xffff0000 -#define CSTRETCH_ALP 0x0000ffff - -/* gpiotimerval */ -#define GPIO_ONTIME_SHIFT 16 - -/* clockcontrol_n */ -#define CN_N1_MASK 0x3f /* n1 control */ -#define CN_N2_MASK 0x3f00 /* n2 control */ -#define CN_N2_SHIFT 8 -#define CN_PLLC_MASK 0xf0000 /* pll control */ -#define CN_PLLC_SHIFT 16 - -/* clockcontrol_sb/pci/uart */ -#define CC_M1_MASK 0x3f /* m1 control */ -#define CC_M2_MASK 0x3f00 /* m2 control */ -#define CC_M2_SHIFT 8 -#define CC_M3_MASK 0x3f0000 /* m3 control */ -#define CC_M3_SHIFT 16 -#define CC_MC_MASK 0x1f000000 /* mux control */ -#define CC_MC_SHIFT 24 - -/* N3M Clock control magic field values */ -#define CC_F6_2 0x02 /* A factor of 2 in */ -#define CC_F6_3 0x03 /* 6-bit fields like */ -#define CC_F6_4 0x05 /* N1, M1 or M3 */ -#define CC_F6_5 0x09 -#define CC_F6_6 0x11 -#define CC_F6_7 0x21 - -#define CC_F5_BIAS 5 /* 5-bit fields get this added */ - -#define CC_MC_BYPASS 0x08 -#define CC_MC_M1 0x04 -#define CC_MC_M1M2 0x02 -#define CC_MC_M1M2M3 0x01 -#define CC_MC_M1M3 0x11 - -/* Type 2 Clock control magic field values */ -#define CC_T2_BIAS 2 /* n1, n2, m1 & m3 bias */ -#define CC_T2M2_BIAS 3 /* m2 bias */ - -#define CC_T2MC_M1BYP 1 -#define CC_T2MC_M2BYP 2 -#define CC_T2MC_M3BYP 4 - -/* Type 6 Clock control magic field values */ -#define CC_T6_MMASK 1 /* bits of interest in m */ -#define CC_T6_M0 120000000 /* sb clock for m = 0 */ -#define CC_T6_M1 100000000 /* sb clock for m = 1 */ -#define SB2MIPS_T6(sb) (2 * (sb)) - -/* Common clock base */ -#define CC_CLOCK_BASE1 24000000 /* Half the clock freq */ -#define CC_CLOCK_BASE2 12500000 /* Alternate crystal on some PLLs */ - -/* Clock control values for 200MHz in 5350 */ -#define CLKC_5350_N 0x0311 -#define CLKC_5350_M 0x04020009 - -/* Flash types in the chipcommon capabilities register */ -#define FLASH_NONE 0x000 /* No flash */ -#define SFLASH_ST 0x100 /* ST serial flash */ -#define SFLASH_AT 0x200 /* Atmel serial flash */ -#define PFLASH 0x700 /* Parallel flash */ - -/* Bits in the ExtBus config registers */ -#define CC_CFG_EN 0x0001 /* Enable */ -#define CC_CFG_EM_MASK 0x000e /* Extif Mode */ -#define CC_CFG_EM_ASYNC 0x0000 /* Async/Parallel flash */ -#define CC_CFG_EM_SYNC 0x0002 /* Synchronous */ -#define CC_CFG_EM_PCMCIA 0x0004 /* PCMCIA */ -#define CC_CFG_EM_IDE 0x0006 /* IDE */ -#define CC_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */ -#define CC_CFG_CD_MASK 0x00e0 /* Sync: Clock divisor, rev >= 20 */ -#define CC_CFG_CE 0x0100 /* Sync: Clock enable, rev >= 20 */ -#define CC_CFG_SB 0x0200 /* Sync: Size/Bytestrobe, rev >= 20 */ -#define CC_CFG_IS 0x0400 /* Extif Sync Clk Select, rev >= 20 */ - -/* ExtBus address space */ -#define CC_EB_BASE 0x1a000000 /* Chipc ExtBus base address */ -#define CC_EB_PCMCIA_MEM 0x1a000000 /* PCMCIA 0 memory base address */ -#define CC_EB_PCMCIA_IO 0x1a200000 /* PCMCIA 0 I/O base address */ -#define CC_EB_PCMCIA_CFG 0x1a400000 /* PCMCIA 0 config base address */ -#define CC_EB_IDE 0x1a800000 /* IDE memory base */ -#define CC_EB_PCMCIA1_MEM 0x1a800000 /* PCMCIA 1 memory base address */ -#define CC_EB_PCMCIA1_IO 0x1aa00000 /* PCMCIA 1 I/O base address */ -#define CC_EB_PCMCIA1_CFG 0x1ac00000 /* PCMCIA 1 config base address */ -#define CC_EB_PROGIF 0x1b000000 /* ProgIF Async/Sync base address */ - -/* Start/busy bit in flashcontrol */ -#define SFLASH_OPCODE 0x000000ff -#define SFLASH_ACTION 0x00000700 -#define SFLASH_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */ -#define SFLASH_START 0x80000000 -#define SFLASH_BUSY SFLASH_START - -/* flashcontrol action codes */ -#define SFLASH_ACT_OPONLY 0x0000 /* Issue opcode only */ -#define SFLASH_ACT_OP1D 0x0100 /* opcode + 1 data byte */ -#define SFLASH_ACT_OP3A 0x0200 /* opcode + 3 addr bytes */ -#define SFLASH_ACT_OP3A1D 0x0300 /* opcode + 3 addr & 1 data bytes */ -#define SFLASH_ACT_OP3A4D 0x0400 /* opcode + 3 addr & 4 data bytes */ -#define SFLASH_ACT_OP3A4X4D 0x0500 /* opcode + 3 addr, 4 don't care & 4 data bytes */ -#define SFLASH_ACT_OP3A1X4D 0x0700 /* opcode + 3 addr, 1 don't care & 4 data bytes */ - -/* flashcontrol action+opcodes for ST flashes */ -#define SFLASH_ST_WREN 0x0006 /* Write Enable */ -#define SFLASH_ST_WRDIS 0x0004 /* Write Disable */ -#define SFLASH_ST_RDSR 0x0105 /* Read Status Register */ -#define SFLASH_ST_WRSR 0x0101 /* Write Status Register */ -#define SFLASH_ST_READ 0x0303 /* Read Data Bytes */ -#define SFLASH_ST_PP 0x0302 /* Page Program */ -#define SFLASH_ST_SE 0x02d8 /* Sector Erase */ -#define SFLASH_ST_BE 0x00c7 /* Bulk Erase */ -#define SFLASH_ST_DP 0x00b9 /* Deep Power-down */ -#define SFLASH_ST_RES 0x03ab /* Read Electronic Signature */ -#define SFLASH_ST_CSA 0x1000 /* Keep chip select asserted */ -#define SFLASH_ST_SSE 0x0220 /* Sub-sector Erase */ - -/* Status register bits for ST flashes */ -#define SFLASH_ST_WIP 0x01 /* Write In Progress */ -#define SFLASH_ST_WEL 0x02 /* Write Enable Latch */ -#define SFLASH_ST_BP_MASK 0x1c /* Block Protect */ -#define SFLASH_ST_BP_SHIFT 2 -#define SFLASH_ST_SRWD 0x80 /* Status Register Write Disable */ - -/* flashcontrol action+opcodes for Atmel flashes */ -#define SFLASH_AT_READ 0x07e8 -#define SFLASH_AT_PAGE_READ 0x07d2 -#define SFLASH_AT_BUF1_READ -#define SFLASH_AT_BUF2_READ -#define SFLASH_AT_STATUS 0x01d7 -#define SFLASH_AT_BUF1_WRITE 0x0384 -#define SFLASH_AT_BUF2_WRITE 0x0387 -#define SFLASH_AT_BUF1_ERASE_PROGRAM 0x0283 -#define SFLASH_AT_BUF2_ERASE_PROGRAM 0x0286 -#define SFLASH_AT_BUF1_PROGRAM 0x0288 -#define SFLASH_AT_BUF2_PROGRAM 0x0289 -#define SFLASH_AT_PAGE_ERASE 0x0281 -#define SFLASH_AT_BLOCK_ERASE 0x0250 -#define SFLASH_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382 -#define SFLASH_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385 -#define SFLASH_AT_BUF1_LOAD 0x0253 -#define SFLASH_AT_BUF2_LOAD 0x0255 -#define SFLASH_AT_BUF1_COMPARE 0x0260 -#define SFLASH_AT_BUF2_COMPARE 0x0261 -#define SFLASH_AT_BUF1_REPROGRAM 0x0258 -#define SFLASH_AT_BUF2_REPROGRAM 0x0259 - -/* Status register bits for Atmel flashes */ -#define SFLASH_AT_READY 0x80 -#define SFLASH_AT_MISMATCH 0x40 -#define SFLASH_AT_ID_MASK 0x38 -#define SFLASH_AT_ID_SHIFT 3 - -/* - * These are the UART port assignments, expressed as offsets from the base - * register. These assignments should hold for any serial port based on - * a 8250, 16450, or 16550(A). - */ - -#define UART_RX 0 /* In: Receive buffer (DLAB=0) */ -#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ -#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ -#define UART_IER 1 /* In/Out: Interrupt Enable Register (DLAB=0) */ -#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ -#define UART_IIR 2 /* In: Interrupt Identity Register */ -#define UART_FCR 2 /* Out: FIFO Control Register */ -#define UART_LCR 3 /* Out: Line Control Register */ -#define UART_MCR 4 /* Out: Modem Control Register */ -#define UART_LSR 5 /* In: Line Status Register */ -#define UART_MSR 6 /* In: Modem Status Register */ -#define UART_SCR 7 /* I/O: Scratch Register */ -#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ -#define UART_LCR_WLEN8 0x03 /* Word length: 8 bits */ -#define UART_MCR_OUT2 0x08 /* MCR GPIO out 2 */ -#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ -#define UART_LSR_RX_FIFO 0x80 /* Receive FIFO error */ -#define UART_LSR_TDHR 0x40 /* Data-hold-register empty */ -#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ -#define UART_LSR_BREAK 0x10 /* Break interrupt */ -#define UART_LSR_FRAMING 0x08 /* Framing error */ -#define UART_LSR_PARITY 0x04 /* Parity error */ -#define UART_LSR_OVERRUN 0x02 /* Overrun error */ -#define UART_LSR_RXRDY 0x01 /* Receiver ready */ -#define UART_FCR_FIFO_ENABLE 1 /* FIFO control register bit controlling FIFO enable/disable */ - -/* Interrupt Identity Register (IIR) bits */ -#define UART_IIR_FIFO_MASK 0xc0 /* IIR FIFO disable/enabled mask */ -#define UART_IIR_INT_MASK 0xf /* IIR interrupt ID source */ -#define UART_IIR_MDM_CHG 0x0 /* Modem status changed */ -#define UART_IIR_NOINT 0x1 /* No interrupt pending */ -#define UART_IIR_THRE 0x2 /* THR empty */ -#define UART_IIR_RCVD_DATA 0x4 /* Received data available */ -#define UART_IIR_RCVR_STATUS 0x6 /* Receiver status */ -#define UART_IIR_CHAR_TIME 0xc /* Character time */ - -/* Interrupt Enable Register (IER) bits */ -#define UART_IER_EDSSI 8 /* enable modem status interrupt */ -#define UART_IER_ELSI 4 /* enable receiver line status interrupt */ -#define UART_IER_ETBEI 2 /* enable transmitter holding register empty interrupt */ -#define UART_IER_ERBFI 1 /* enable data available interrupt */ - -/* pmustatus */ -#define PST_EXTLPOAVAIL 0x0100 -#define PST_WDRESET 0x0080 -#define PST_INTPEND 0x0040 -#define PST_SBCLKST 0x0030 -#define PST_SBCLKST_ILP 0x0010 -#define PST_SBCLKST_ALP 0x0020 -#define PST_SBCLKST_HT 0x0030 -#define PST_ALPAVAIL 0x0008 -#define PST_HTAVAIL 0x0004 -#define PST_RESINIT 0x0003 - /* pmucapabilities */ #define PCAP_REV_MASK 0x000000ff #define PCAP_RC_MASK 0x00001f00 @@ -834,755 +277,10 @@ typedef volatile struct { #define PCAP5_CC_MASK 0xf8000000 #define PCAP5_CC_SHIFT 27 -/* PMU Resource Request Timer registers */ -/* This is based on PmuRev0 */ -#define PRRT_TIME_MASK 0x03ff -#define PRRT_INTEN 0x0400 -#define PRRT_REQ_ACTIVE 0x0800 -#define PRRT_ALP_REQ 0x1000 -#define PRRT_HT_REQ 0x2000 - -/* PMU resource bit position */ -#define PMURES_BIT(bit) (1 << (bit)) - -/* PMU resource number limit */ -#define PMURES_MAX_RESNUM 30 - -/* PMU chip control0 register */ -#define PMU_CHIPCTL0 0 - -/* PMU chip control1 register */ -#define PMU_CHIPCTL1 1 -#define PMU_CC1_RXC_DLL_BYPASS 0x00010000 - -#define PMU_CC1_IF_TYPE_MASK 0x00000030 -#define PMU_CC1_IF_TYPE_RMII 0x00000000 -#define PMU_CC1_IF_TYPE_MII 0x00000010 -#define PMU_CC1_IF_TYPE_RGMII 0x00000020 - -#define PMU_CC1_SW_TYPE_MASK 0x000000c0 -#define PMU_CC1_SW_TYPE_EPHY 0x00000000 -#define PMU_CC1_SW_TYPE_EPHYMII 0x00000040 -#define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080 -#define PMU_CC1_SW_TYPE_RGMII 0x000000c0 - -/* PMU corerev and chip specific PLL controls. - * PMU_PLL_XX where is PMU corerev and is an arbitrary number - * to differentiate different PLLs controlled by the same PMU rev. - */ -/* pllcontrol registers */ -/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */ -#define PMU0_PLL0_PLLCTL0 0 -#define PMU0_PLL0_PC0_PDIV_MASK 1 -#define PMU0_PLL0_PC0_PDIV_FREQ 25000 -#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038 -#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3 -#define PMU0_PLL0_PC0_DIV_ARM_BASE 8 - -/* PC0_DIV_ARM for PLLOUT_ARM */ -#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0 -#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1 -#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2 -#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */ -#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4 -#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5 -#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6 -#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7 - -/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */ -#define PMU0_PLL0_PLLCTL1 1 -#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000 -#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28 -#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00 -#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8 -#define PMU0_PLL0_PC1_STOP_MOD 0x00000040 - -/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */ -#define PMU0_PLL0_PLLCTL2 2 -#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf -#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4 - -/* pllcontrol registers */ -/* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ -#define PMU1_PLL0_PLLCTL0 0 -#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000 -#define PMU1_PLL0_PC0_P1DIV_SHIFT 20 -#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000 -#define PMU1_PLL0_PC0_P2DIV_SHIFT 24 - -/* mdiv */ -#define PMU1_PLL0_PLLCTL1 1 -#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff -#define PMU1_PLL0_PC1_M1DIV_SHIFT 0 -#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00 -#define PMU1_PLL0_PC1_M2DIV_SHIFT 8 -#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000 -#define PMU1_PLL0_PC1_M3DIV_SHIFT 16 -#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000 -#define PMU1_PLL0_PC1_M4DIV_SHIFT 24 - -#define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8 -#define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) -#define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT) - -/* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ -#define PMU1_PLL0_PLLCTL2 2 -#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff -#define PMU1_PLL0_PC2_M5DIV_SHIFT 0 -#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00 -#define PMU1_PLL0_PC2_M6DIV_SHIFT 8 -#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000 -#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17 -#define PMU1_PLL0_PC2_NDIV_MODE_MASH 1 -#define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */ -#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000 -#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20 - -/* ndiv_frac */ -#define PMU1_PLL0_PLLCTL3 3 -#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff -#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0 - -/* pll_ctrl */ -#define PMU1_PLL0_PLLCTL4 4 - -/* pll_ctrl, vco_rng, clkdrive_ch */ -#define PMU1_PLL0_PLLCTL5 5 -#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00 -#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8 - -/* PMU rev 2 control words */ -#define PMU2_PHY_PLL_PLLCTL 4 -#define PMU2_SI_PLL_PLLCTL 10 - -/* PMU rev 2 */ -/* pllcontrol registers */ -/* ndiv_pwrdn, pwrdn_ch, refcomp_pwrdn, dly_ch, p1div, p2div, _bypass_sdmod */ -#define PMU2_PLL_PLLCTL0 0 -#define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000 -#define PMU2_PLL_PC0_P1DIV_SHIFT 20 -#define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000 -#define PMU2_PLL_PC0_P2DIV_SHIFT 24 - -/* mdiv */ -#define PMU2_PLL_PLLCTL1 1 -#define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff -#define PMU2_PLL_PC1_M1DIV_SHIFT 0 -#define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00 -#define PMU2_PLL_PC1_M2DIV_SHIFT 8 -#define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000 -#define PMU2_PLL_PC1_M3DIV_SHIFT 16 -#define PMU2_PLL_PC1_M4DIV_MASK 0xff000000 -#define PMU2_PLL_PC1_M4DIV_SHIFT 24 - -/* mdiv, ndiv_dither_mfb, ndiv_mode, ndiv_int */ -#define PMU2_PLL_PLLCTL2 2 -#define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff -#define PMU2_PLL_PC2_M5DIV_SHIFT 0 -#define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00 -#define PMU2_PLL_PC2_M6DIV_SHIFT 8 -#define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000 -#define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17 -#define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000 -#define PMU2_PLL_PC2_NDIV_INT_SHIFT 20 - -/* ndiv_frac */ -#define PMU2_PLL_PLLCTL3 3 -#define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff -#define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0 - -/* pll_ctrl */ -#define PMU2_PLL_PLLCTL4 4 - -/* pll_ctrl, vco_rng, clkdrive_ch */ -#define PMU2_PLL_PLLCTL5 5 -#define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00 -#define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8 -#define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000 -#define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12 -#define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000 -#define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16 -#define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000 -#define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20 -#define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000 -#define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24 -#define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000 -#define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28 - -/* PMU rev 5 (& 6) */ -#define PMU5_PLL_P1P2_OFF 0 -#define PMU5_PLL_P1_MASK 0x0f000000 -#define PMU5_PLL_P1_SHIFT 24 -#define PMU5_PLL_P2_MASK 0x00f00000 -#define PMU5_PLL_P2_SHIFT 20 -#define PMU5_PLL_M14_OFF 1 -#define PMU5_PLL_MDIV_MASK 0x000000ff -#define PMU5_PLL_MDIV_WIDTH 8 -#define PMU5_PLL_NM5_OFF 2 -#define PMU5_PLL_NDIV_MASK 0xfff00000 -#define PMU5_PLL_NDIV_SHIFT 20 -#define PMU5_PLL_NDIV_MODE_MASK 0x000e0000 -#define PMU5_PLL_NDIV_MODE_SHIFT 17 -#define PMU5_PLL_FMAB_OFF 3 -#define PMU5_PLL_MRAT_MASK 0xf0000000 -#define PMU5_PLL_MRAT_SHIFT 28 -#define PMU5_PLL_ABRAT_MASK 0x08000000 -#define PMU5_PLL_ABRAT_SHIFT 27 -#define PMU5_PLL_FDIV_MASK 0x07ffffff -#define PMU5_PLL_PLLCTL_OFF 4 -#define PMU5_PLL_PCHI_OFF 5 -#define PMU5_PLL_PCHI_MASK 0x0000003f - -/* pmu XtalFreqRatio */ -#define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF -#define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000 -#define PMU_XTALFREQ_REG_MEASURE_SHIFT 31 - -/* Divider allocation in 4716/47162/5356/5357 */ -#define PMU5_MAINPLL_CPU 1 -#define PMU5_MAINPLL_MEM 2 -#define PMU5_MAINPLL_SI 3 - -#define PMU7_PLL_PLLCTL7 7 -#define PMU7_PLL_PLLCTL8 8 -#define PMU7_PLL_PLLCTL11 11 - -/* PLL usage in 4716/47162 */ -#define PMU4716_MAINPLL_PLL0 12 - -/* PLL usage in 5356/5357 */ -#define PMU5356_MAINPLL_PLL0 0 -#define PMU5357_MAINPLL_PLL0 0 - -/* 4716/47162 resources */ -#define RES4716_PROC_PLL_ON 0x00000040 -#define RES4716_PROC_HT_AVAIL 0x00000080 - -/* 4716/4717/4718 Chip specific ChipControl register bits */ -#define CCTRL471X_I2S_PINS_ENABLE 0x0080 /* I2S pins off by default, shared with pflash */ - -/* 5354 resources */ -#define RES5354_EXT_SWITCHER_PWM 0 /* 0x00001 */ -#define RES5354_BB_SWITCHER_PWM 1 /* 0x00002 */ -#define RES5354_BB_SWITCHER_BURST 2 /* 0x00004 */ -#define RES5354_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */ -#define RES5354_ILP_REQUEST 4 /* 0x00010 */ -#define RES5354_RADIO_SWITCHER_PWM 5 /* 0x00020 */ -#define RES5354_RADIO_SWITCHER_BURST 6 /* 0x00040 */ -#define RES5354_ROM_SWITCH 7 /* 0x00080 */ -#define RES5354_PA_REF_LDO 8 /* 0x00100 */ -#define RES5354_RADIO_LDO 9 /* 0x00200 */ -#define RES5354_AFE_LDO 10 /* 0x00400 */ -#define RES5354_PLL_LDO 11 /* 0x00800 */ -#define RES5354_BG_FILTBYP 12 /* 0x01000 */ -#define RES5354_TX_FILTBYP 13 /* 0x02000 */ -#define RES5354_RX_FILTBYP 14 /* 0x04000 */ -#define RES5354_XTAL_PU 15 /* 0x08000 */ -#define RES5354_XTAL_EN 16 /* 0x10000 */ -#define RES5354_BB_PLL_FILTBYP 17 /* 0x20000 */ -#define RES5354_RF_PLL_FILTBYP 18 /* 0x40000 */ -#define RES5354_BB_PLL_PU 19 /* 0x80000 */ - -/* 5357 Chip specific ChipControl register bits */ -#define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */ -#define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */ - -/* 4328 resources */ -#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */ -#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */ -#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */ -#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */ -#define RES4328_ILP_REQUEST 4 /* 0x00010 */ -#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */ -#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */ -#define RES4328_ROM_SWITCH 7 /* 0x00080 */ -#define RES4328_PA_REF_LDO 8 /* 0x00100 */ -#define RES4328_RADIO_LDO 9 /* 0x00200 */ -#define RES4328_AFE_LDO 10 /* 0x00400 */ -#define RES4328_PLL_LDO 11 /* 0x00800 */ -#define RES4328_BG_FILTBYP 12 /* 0x01000 */ -#define RES4328_TX_FILTBYP 13 /* 0x02000 */ -#define RES4328_RX_FILTBYP 14 /* 0x04000 */ -#define RES4328_XTAL_PU 15 /* 0x08000 */ -#define RES4328_XTAL_EN 16 /* 0x10000 */ -#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */ -#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */ -#define RES4328_BB_PLL_PU 19 /* 0x80000 */ - -/* 4325 A0/A1 resources */ -#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */ -#define RES4325_CBUCK_BURST 1 /* 0x00000002 */ -#define RES4325_CBUCK_PWM 2 /* 0x00000004 */ -#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */ -#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */ -#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */ -#define RES4325_ILP_REQUEST 6 /* 0x00000040 */ -#define RES4325_ABUCK_BURST 7 /* 0x00000080 */ -#define RES4325_ABUCK_PWM 8 /* 0x00000100 */ -#define RES4325_LNLDO1_PU 9 /* 0x00000200 */ -#define RES4325_OTP_PU 10 /* 0x00000400 */ -#define RES4325_LNLDO3_PU 11 /* 0x00000800 */ -#define RES4325_LNLDO4_PU 12 /* 0x00001000 */ -#define RES4325_XTAL_PU 13 /* 0x00002000 */ -#define RES4325_ALP_AVAIL 14 /* 0x00004000 */ -#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */ -#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */ -#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */ -#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */ -#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */ -#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */ -#define RES4325_HT_AVAIL 21 /* 0x00200000 */ - -/* 4325 B0/C0 resources */ -#define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */ -#define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */ -#define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */ -#define RES4325B0_CLDO_PU 4 /* 0x00000010 */ - -/* 4325 C1 resources */ -#define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */ - -/* 4325 chip-specific ChipStatus register bits */ -#define CST4325_SPROM_OTP_SEL_MASK 0x00000003 -#define CST4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ -#define CST4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ -#define CST4325_OTP_SEL 2 /* OTP is powered up, no SPROM */ -#define CST4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ -#define CST4325_SDIO_USB_MODE_MASK 0x00000004 -#define CST4325_SDIO_USB_MODE_SHIFT 2 -#define CST4325_RCAL_VALID_MASK 0x00000008 -#define CST4325_RCAL_VALID_SHIFT 3 -#define CST4325_RCAL_VALUE_MASK 0x000001f0 -#define CST4325_RCAL_VALUE_SHIFT 4 -#define CST4325_PMUTOP_2B_MASK 0x00000200 /* 1 for 2b, 0 for to 2a */ -#define CST4325_PMUTOP_2B_SHIFT 9 - -#define RES4329_RESERVED0 0 /* 0x00000001 */ -#define RES4329_CBUCK_LPOM 1 /* 0x00000002 */ -#define RES4329_CBUCK_BURST 2 /* 0x00000004 */ -#define RES4329_CBUCK_PWM 3 /* 0x00000008 */ -#define RES4329_CLDO_PU 4 /* 0x00000010 */ -#define RES4329_PALDO_PU 5 /* 0x00000020 */ -#define RES4329_ILP_REQUEST 6 /* 0x00000040 */ -#define RES4329_RESERVED7 7 /* 0x00000080 */ -#define RES4329_RESERVED8 8 /* 0x00000100 */ -#define RES4329_LNLDO1_PU 9 /* 0x00000200 */ -#define RES4329_OTP_PU 10 /* 0x00000400 */ -#define RES4329_RESERVED11 11 /* 0x00000800 */ -#define RES4329_LNLDO2_PU 12 /* 0x00001000 */ -#define RES4329_XTAL_PU 13 /* 0x00002000 */ -#define RES4329_ALP_AVAIL 14 /* 0x00004000 */ -#define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */ -#define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */ -#define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */ -#define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */ -#define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */ -#define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */ -#define RES4329_HT_AVAIL 21 /* 0x00200000 */ - -#define CST4329_SPROM_OTP_SEL_MASK 0x00000003 -#define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ -#define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ -#define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */ -#define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ -#define CST4329_SPI_SDIO_MODE_MASK 0x00000004 -#define CST4329_SPI_SDIO_MODE_SHIFT 2 - -/* 4312 chip-specific ChipStatus register bits */ -#define CST4312_SPROM_OTP_SEL_MASK 0x00000003 -#define CST4312_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ -#define CST4312_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ -#define CST4312_OTP_SEL 2 /* OTP is powered up, no SPROM */ -#define CST4312_OTP_BAD 3 /* OTP is broken, SPROM is present */ - -/* 4312 resources (all PMU chips with little memory constraint) */ -#define RES4312_SWITCHER_BURST 0 /* 0x00000001 */ -#define RES4312_SWITCHER_PWM 1 /* 0x00000002 */ -#define RES4312_PA_REF_LDO 2 /* 0x00000004 */ -#define RES4312_CORE_LDO_BURST 3 /* 0x00000008 */ -#define RES4312_CORE_LDO_PWM 4 /* 0x00000010 */ -#define RES4312_RADIO_LDO 5 /* 0x00000020 */ -#define RES4312_ILP_REQUEST 6 /* 0x00000040 */ -#define RES4312_BG_FILTBYP 7 /* 0x00000080 */ -#define RES4312_TX_FILTBYP 8 /* 0x00000100 */ -#define RES4312_RX_FILTBYP 9 /* 0x00000200 */ -#define RES4312_XTAL_PU 10 /* 0x00000400 */ -#define RES4312_ALP_AVAIL 11 /* 0x00000800 */ -#define RES4312_BB_PLL_FILTBYP 12 /* 0x00001000 */ -#define RES4312_RF_PLL_FILTBYP 13 /* 0x00002000 */ -#define RES4312_HT_AVAIL 14 /* 0x00004000 */ - -/* 4322 resources */ -#define RES4322_RF_LDO 0 -#define RES4322_ILP_REQUEST 1 -#define RES4322_XTAL_PU 2 -#define RES4322_ALP_AVAIL 3 -#define RES4322_SI_PLL_ON 4 -#define RES4322_HT_SI_AVAIL 5 -#define RES4322_PHY_PLL_ON 6 -#define RES4322_HT_PHY_AVAIL 7 -#define RES4322_OTP_PU 8 - -/* 4322 chip-specific ChipStatus register bits */ -#define CST4322_XTAL_FREQ_20_40MHZ 0x00000020 -#define CST4322_SPROM_OTP_SEL_MASK 0x000000c0 -#define CST4322_SPROM_OTP_SEL_SHIFT 6 -#define CST4322_NO_SPROM_OTP 0 /* no OTP, no SPROM */ -#define CST4322_SPROM_PRESENT 1 /* SPROM is present */ -#define CST4322_OTP_PRESENT 2 /* OTP is present */ -#define CST4322_PCI_OR_USB 0x00000100 -#define CST4322_BOOT_MASK 0x00000600 -#define CST4322_BOOT_SHIFT 9 -#define CST4322_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ -#define CST4322_BOOT_FROM_ROM 1 /* boot from ROM */ -#define CST4322_BOOT_FROM_FLASH 2 /* boot from FLASH */ -#define CST4322_BOOT_FROM_INVALID 3 -#define CST4322_ILP_DIV_EN 0x00000800 -#define CST4322_FLASH_TYPE_MASK 0x00001000 -#define CST4322_FLASH_TYPE_SHIFT 12 -#define CST4322_FLASH_TYPE_SHIFT_ST 0 /* ST serial FLASH */ -#define CST4322_FLASH_TYPE_SHIFT_ATMEL 1 /* ATMEL flash */ -#define CST4322_ARM_TAP_SEL 0x00002000 -#define CST4322_RES_INIT_MODE_MASK 0x0000c000 -#define CST4322_RES_INIT_MODE_SHIFT 14 -#define CST4322_RES_INIT_MODE_ILPAVAIL 0 /* resinitmode: ILP available */ -#define CST4322_RES_INIT_MODE_ILPREQ 1 /* resinitmode: ILP request */ -#define CST4322_RES_INIT_MODE_ALPAVAIL 2 /* resinitmode: ALP available */ -#define CST4322_RES_INIT_MODE_HTAVAIL 3 /* resinitmode: HT available */ -#define CST4322_PCIPLLCLK_GATING 0x00010000 -#define CST4322_CLK_SWITCH_PCI_TO_ALP 0x00020000 -#define CST4322_PCI_CARDBUS_MODE 0x00040000 - -/* 43224 chip-specific ChipControl register bits */ -#define CCTRL43224_GPIO_TOGGLE 0x8000 -#define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */ -#define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */ - -/* 43236 resources */ -#define RES43236_REGULATOR 0 -#define RES43236_ILP_REQUEST 1 -#define RES43236_XTAL_PU 2 -#define RES43236_ALP_AVAIL 3 -#define RES43236_SI_PLL_ON 4 -#define RES43236_HT_SI_AVAIL 5 - -/* 43236 chip-specific ChipControl register bits */ -#define CCTRL43236_BT_COEXIST (1<<0) /* 0 disable */ -#define CCTRL43236_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ -#define CCTRL43236_EXT_LNA (1<<2) /* 0 disable */ -#define CCTRL43236_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */ -#define CCTRL43236_GSIO (1<<4) /* 0 disable */ - -/* 43236 Chip specific ChipStatus register bits */ -#define CST43236_SFLASH_MASK 0x00000040 -#define CST43236_OTP_MASK 0x00000080 -#define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */ -#define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */ -#define CST43236_BOOT_MASK 0x00001800 -#define CST43236_BOOT_SHIFT 11 -#define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */ -#define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */ -#define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */ -#define CST43236_BOOT_FROM_INVALID 3 - -/* 4331 resources */ -#define RES4331_REGULATOR 0 -#define RES4331_ILP_REQUEST 1 -#define RES4331_XTAL_PU 2 -#define RES4331_ALP_AVAIL 3 -#define RES4331_SI_PLL_ON 4 -#define RES4331_HT_SI_AVAIL 5 - -/* 4331 chip-specific ChipControl register bits */ -#define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */ -#define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */ -#define CCTRL4331_EXT_LNA (1<<2) /* 0 disable */ -#define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */ -#define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */ -#define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */ -#define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */ -#define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */ -#define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */ -#define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */ -#define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */ -#define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */ -#define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */ -#define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */ - -/* 4331 Chip specific ChipStatus register bits */ -#define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */ -#define CST4331_SPROM_PRESENT 0x00000002 -#define CST4331_OTP_PRESENT 0x00000004 -#define CST4331_LDO_RF 0x00000008 -#define CST4331_LDO_PAR 0x00000010 - -/* 4315 resources */ -#define RES4315_CBUCK_LPOM 1 /* 0x00000002 */ -#define RES4315_CBUCK_BURST 2 /* 0x00000004 */ -#define RES4315_CBUCK_PWM 3 /* 0x00000008 */ -#define RES4315_CLDO_PU 4 /* 0x00000010 */ -#define RES4315_PALDO_PU 5 /* 0x00000020 */ -#define RES4315_ILP_REQUEST 6 /* 0x00000040 */ -#define RES4315_LNLDO1_PU 9 /* 0x00000200 */ -#define RES4315_OTP_PU 10 /* 0x00000400 */ -#define RES4315_LNLDO2_PU 12 /* 0x00001000 */ -#define RES4315_XTAL_PU 13 /* 0x00002000 */ -#define RES4315_ALP_AVAIL 14 /* 0x00004000 */ -#define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */ -#define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */ -#define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */ -#define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */ -#define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */ -#define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */ -#define RES4315_HT_AVAIL 21 /* 0x00200000 */ - -/* 4315 chip-specific ChipStatus register bits */ -#define CST4315_SPROM_OTP_SEL_MASK 0x00000003 /* gpio [7:6], SDIO CIS selection */ -#define CST4315_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */ -#define CST4315_SPROM_SEL 0x00000001 /* use SPROM, OTP is powered up */ -#define CST4315_OTP_SEL 0x00000002 /* use OTP, OTP is powered up */ -#define CST4315_OTP_PWRDN 0x00000003 /* use SPROM, OTP is powered down */ -#define CST4315_SDIO_MODE 0x00000004 /* gpio [8], sdio/usb mode */ -#define CST4315_RCAL_VALID 0x00000008 -#define CST4315_RCAL_VALUE_MASK 0x000001f0 -#define CST4315_RCAL_VALUE_SHIFT 4 -#define CST4315_PALDO_EXTPNP 0x00000200 /* PALDO is configured with external PNP */ -#define CST4315_CBUCK_MODE_MASK 0x00000c00 -#define CST4315_CBUCK_MODE_BURST 0x00000400 -#define CST4315_CBUCK_MODE_LPBURST 0x00000c00 - -/* 4319 resources */ -#define RES4319_CBUCK_LPOM 1 /* 0x00000002 */ -#define RES4319_CBUCK_BURST 2 /* 0x00000004 */ -#define RES4319_CBUCK_PWM 3 /* 0x00000008 */ -#define RES4319_CLDO_PU 4 /* 0x00000010 */ -#define RES4319_PALDO_PU 5 /* 0x00000020 */ -#define RES4319_ILP_REQUEST 6 /* 0x00000040 */ -#define RES4319_LNLDO1_PU 9 /* 0x00000200 */ -#define RES4319_OTP_PU 10 /* 0x00000400 */ -#define RES4319_LNLDO2_PU 12 /* 0x00001000 */ -#define RES4319_XTAL_PU 13 /* 0x00002000 */ -#define RES4319_ALP_AVAIL 14 /* 0x00004000 */ -#define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */ -#define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */ -#define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */ -#define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */ -#define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */ -#define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */ -#define RES4319_HT_AVAIL 21 /* 0x00200000 */ - -/* 4319 chip-specific ChipStatus register bits */ -#define CST4319_SPI_CPULESSUSB 0x00000001 -#define CST4319_SPI_CLK_POL 0x00000002 -#define CST4319_SPI_CLK_PH 0x00000008 -#define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */ -#define CST4319_SPROM_OTP_SEL_SHIFT 6 -#define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */ -#define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */ -#define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */ -#define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */ -#define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */ -#define CST4319_REMAP_SEL_MASK 0x00000600 -#define CST4319_ILPDIV_EN 0x00000800 -#define CST4319_XTAL_PD_POL 0x00001000 -#define CST4319_LPO_SEL 0x00002000 -#define CST4319_RES_INIT_MODE 0x0000c000 -#define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */ -#define CST4319_CBUCK_MODE_MASK 0x00060000 -#define CST4319_CBUCK_MODE_BURST 0x00020000 -#define CST4319_CBUCK_MODE_LPBURST 0x00060000 -#define CST4319_RCAL_VALID 0x01000000 -#define CST4319_RCAL_VALUE_MASK 0x3e000000 -#define CST4319_RCAL_VALUE_SHIFT 25 - -#define PMU1_PLL0_CHIPCTL0 0 -#define PMU1_PLL0_CHIPCTL1 1 -#define PMU1_PLL0_CHIPCTL2 2 -#define CCTL_4319USB_XTAL_SEL_MASK 0x00180000 -#define CCTL_4319USB_XTAL_SEL_SHIFT 19 -#define CCTL_4319USB_48MHZ_PLL_SEL 1 -#define CCTL_4319USB_24MHZ_PLL_SEL 2 - -/* PMU resources for 4336 */ -#define RES4336_CBUCK_LPOM 0 -#define RES4336_CBUCK_BURST 1 -#define RES4336_CBUCK_LP_PWM 2 -#define RES4336_CBUCK_PWM 3 -#define RES4336_CLDO_PU 4 -#define RES4336_DIS_INT_RESET_PD 5 -#define RES4336_ILP_REQUEST 6 -#define RES4336_LNLDO_PU 7 -#define RES4336_LDO3P3_PU 8 -#define RES4336_OTP_PU 9 -#define RES4336_XTAL_PU 10 -#define RES4336_ALP_AVAIL 11 -#define RES4336_RADIO_PU 12 -#define RES4336_BG_PU 13 -#define RES4336_VREG1p4_PU_PU 14 -#define RES4336_AFE_PWRSW_PU 15 -#define RES4336_RX_PWRSW_PU 16 -#define RES4336_TX_PWRSW_PU 17 -#define RES4336_BB_PWRSW_PU 18 -#define RES4336_SYNTH_PWRSW_PU 19 -#define RES4336_MISC_PWRSW_PU 20 -#define RES4336_LOGEN_PWRSW_PU 21 -#define RES4336_BBPLL_PWRSW_PU 22 -#define RES4336_MACPHY_CLKAVAIL 23 -#define RES4336_HT_AVAIL 24 -#define RES4336_RSVD 25 - -/* 4336 chip-specific ChipStatus register bits */ -#define CST4336_SPI_MODE_MASK 0x00000001 -#define CST4336_SPROM_PRESENT 0x00000002 -#define CST4336_OTP_PRESENT 0x00000004 -#define CST4336_ARMREMAP_0 0x00000008 -#define CST4336_ILPDIV_EN_MASK 0x00000010 -#define CST4336_ILPDIV_EN_SHIFT 4 -#define CST4336_XTAL_PD_POL_MASK 0x00000020 -#define CST4336_XTAL_PD_POL_SHIFT 5 -#define CST4336_LPO_SEL_MASK 0x00000040 -#define CST4336_LPO_SEL_SHIFT 6 -#define CST4336_RES_INIT_MODE_MASK 0x00000180 -#define CST4336_RES_INIT_MODE_SHIFT 7 -#define CST4336_CBUCK_MODE_MASK 0x00000600 -#define CST4336_CBUCK_MODE_SHIFT 9 - -/* 4330 resources */ -#define RES4330_CBUCK_LPOM 0 -#define RES4330_CBUCK_BURST 1 -#define RES4330_CBUCK_LP_PWM 2 -#define RES4330_CBUCK_PWM 3 -#define RES4330_CLDO_PU 4 -#define RES4330_DIS_INT_RESET_PD 5 -#define RES4330_ILP_REQUEST 6 -#define RES4330_LNLDO_PU 7 -#define RES4330_LDO3P3_PU 8 -#define RES4330_OTP_PU 9 -#define RES4330_XTAL_PU 10 -#define RES4330_ALP_AVAIL 11 -#define RES4330_RADIO_PU 12 -#define RES4330_BG_PU 13 -#define RES4330_VREG1p4_PU_PU 14 -#define RES4330_AFE_PWRSW_PU 15 -#define RES4330_RX_PWRSW_PU 16 -#define RES4330_TX_PWRSW_PU 17 -#define RES4330_BB_PWRSW_PU 18 -#define RES4330_SYNTH_PWRSW_PU 19 -#define RES4330_MISC_PWRSW_PU 20 -#define RES4330_LOGEN_PWRSW_PU 21 -#define RES4330_BBPLL_PWRSW_PU 22 -#define RES4330_MACPHY_CLKAVAIL 23 -#define RES4330_HT_AVAIL 24 -#define RES4330_5gRX_PWRSW_PU 25 -#define RES4330_5gTX_PWRSW_PU 26 -#define RES4330_5g_LOGEN_PWRSW_PU 27 - -/* 4330 chip-specific ChipStatus register bits */ -#define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */ -#define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */ -#define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */ -#define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */ -#define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */ -#define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */ -#define CST4330_OTP_PRESENT 0x00000010 -#define CST4330_LPO_AUTODET_EN 0x00000020 -#define CST4330_ARMREMAP_0 0x00000040 -#define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */ -#define CST4330_ILPDIV_EN 0x00000100 -#define CST4330_LPO_SEL 0x00000200 -#define CST4330_RES_INIT_MODE_SHIFT 10 -#define CST4330_RES_INIT_MODE_MASK 0x00000c00 -#define CST4330_CBUCK_MODE_SHIFT 12 -#define CST4330_CBUCK_MODE_MASK 0x00003000 -#define CST4330_CBUCK_POWER_OK 0x00004000 -#define CST4330_BB_PLL_LOCKED 0x00008000 -#define SOCDEVRAM_4330_BP_ADDR 0x1E000000 -#define SOCDEVRAM_4330_ARM_ADDR 0x00800000 - -/* 4313 resources */ -#define RES4313_BB_PU_RSRC 0 -#define RES4313_ILP_REQ_RSRC 1 -#define RES4313_XTAL_PU_RSRC 2 -#define RES4313_ALP_AVAIL_RSRC 3 -#define RES4313_RADIO_PU_RSRC 4 -#define RES4313_BG_PU_RSRC 5 -#define RES4313_VREG1P4_PU_RSRC 6 -#define RES4313_AFE_PWRSW_RSRC 7 -#define RES4313_RX_PWRSW_RSRC 8 -#define RES4313_TX_PWRSW_RSRC 9 -#define RES4313_BB_PWRSW_RSRC 10 -#define RES4313_SYNTH_PWRSW_RSRC 11 -#define RES4313_MISC_PWRSW_RSRC 12 -#define RES4313_BB_PLL_PWRSW_RSRC 13 -#define RES4313_HT_AVAIL_RSRC 14 -#define RES4313_MACPHY_CLK_AVAIL_RSRC 15 - -/* 4313 chip-specific ChipStatus register bits */ -#define CST4313_SPROM_PRESENT 1 -#define CST4313_OTP_PRESENT 2 -#define CST4313_SPROM_OTP_SEL_MASK 0x00000002 -#define CST4313_SPROM_OTP_SEL_SHIFT 0 - -/* 4313 Chip specific ChipControl register bits */ -#define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ - -/* 43228 resources */ -#define RES43228_NOT_USED 0 -#define RES43228_ILP_REQUEST 1 -#define RES43228_XTAL_PU 2 -#define RES43228_ALP_AVAIL 3 -#define RES43228_PLL_EN 4 -#define RES43228_HT_PHY_AVAIL 5 - -/* 43228 chipstatus reg bits */ -#define CST43228_ILP_DIV_EN 0x1 -#define CST43228_OTP_PRESENT 0x2 -#define CST43228_SERDES_REFCLK_PADSEL 0x4 -#define CST43228_SDIO_MODE 0x8 - -#define CST43228_SDIO_OTP_PRESENT 0x10 -#define CST43228_SDIO_RESET 0x20 - /* * Maximum delay for the PMU state transition in us. * This is an upper bound intended for spinwaits etc. */ #define PMU_MAX_TRANSITION_DLY 15000 -/* PMU resource up transition time in ILP cycles */ -#define PMURES_UP_TRANSITION 2 - -/* -* Register eci_inputlo bitfield values. -* - BT packet type information bits [7:0] -*/ -/* [3:0] - Task (link) type */ -#define BT_ACL 0x00 -#define BT_SCO 0x01 -#define BT_eSCO 0x02 -#define BT_A2DP 0x03 -#define BT_SNIFF 0x04 -#define BT_PAGE_SCAN 0x05 -#define BT_INQUIRY_SCAN 0x06 -#define BT_PAGE 0x07 -#define BT_INQUIRY 0x08 -#define BT_MSS 0x09 -#define BT_PARK 0x0a -#define BT_RSSISCAN 0x0b -#define BT_MD_ACL 0x0c -#define BT_MD_eSCO 0x0d -#define BT_SCAN_WITH_SCO_LINK 0x0e -#define BT_SCAN_WITHOUT_SCO_LINK 0x0f -/* [7:4] = packet duration code */ -/* [8] - Master / Slave */ -#define BT_MASTER 0 -#define BT_SLAVE 1 -/* [11:9] - multi-level priority */ -#define BT_LOWEST_PRIO 0x0 -#define BT_HIGHEST_PRIO 0x3 - -/* WLAN - number of antenna */ -#define WLAN_NUM_ANT1 TXANT_0 -#define WLAN_NUM_ANT2 TXANT_1 - #endif /* _SBCHIPC_H */ diff --git a/drivers/staging/brcm80211/include/sbconfig.h b/drivers/staging/brcm80211/include/sbconfig.h index 5247f01ec364..68e4b5420a98 100644 --- a/drivers/staging/brcm80211/include/sbconfig.h +++ b/drivers/staging/brcm80211/include/sbconfig.h @@ -24,249 +24,9 @@ #define PAD _XSTR(__LINE__) #endif -/* enumeration in SB is based on the premise that cores are contiguos in the - * enumeration space. - */ -#define SB_BUS_SIZE 0x10000 /* Each bus gets 64Kbytes for cores */ -#define SB_BUS_BASE(b) (SI_ENUM_BASE + (b) * SB_BUS_SIZE) -#define SB_BUS_MAXCORES (SB_BUS_SIZE / SI_CORE_SIZE) /* Max cores per bus */ - /* * Sonics Configuration Space Registers. */ #define SBCONFIGOFF 0xf00 /* core sbconfig regs are top 256bytes of regs */ -#define SBCONFIGSIZE 256 /* sizeof (sbconfig_t) */ - -#define SBIPSFLAG 0x08 -#define SBTPSFLAG 0x18 -#define SBTMERRLOGA 0x48 /* sonics >= 2.3 */ -#define SBTMERRLOG 0x50 /* sonics >= 2.3 */ -#define SBADMATCH3 0x60 -#define SBADMATCH2 0x68 -#define SBADMATCH1 0x70 -#define SBIMSTATE 0x90 -#define SBINTVEC 0x94 -#define SBTMSTATELOW 0x98 -#define SBTMSTATEHIGH 0x9c -#define SBBWA0 0xa0 -#define SBIMCONFIGLOW 0xa8 -#define SBIMCONFIGHIGH 0xac -#define SBADMATCH0 0xb0 -#define SBTMCONFIGLOW 0xb8 -#define SBTMCONFIGHIGH 0xbc -#define SBBCONFIG 0xc0 -#define SBBSTATE 0xc8 -#define SBACTCNFG 0xd8 -#define SBFLAGST 0xe8 -#define SBIDLOW 0xf8 -#define SBIDHIGH 0xfc - -/* All the previous registers are above SBCONFIGOFF, but with Sonics 2.3, we have - * a few registers *below* that line. I think it would be very confusing to try - * and change the value of SBCONFIGOFF, so I'm definig them as absolute offsets here, - */ - -#define SBIMERRLOGA 0xea8 -#define SBIMERRLOG 0xeb0 -#define SBTMPORTCONNID0 0xed8 -#define SBTMPORTLOCK0 0xef8 - -#ifndef _LANGUAGE_ASSEMBLY - -typedef volatile struct _sbconfig { - u32 PAD[2]; - u32 sbipsflag; /* initiator port ocp slave flag */ - u32 PAD[3]; - u32 sbtpsflag; /* target port ocp slave flag */ - u32 PAD[11]; - u32 sbtmerrloga; /* (sonics >= 2.3) */ - u32 PAD; - u32 sbtmerrlog; /* (sonics >= 2.3) */ - u32 PAD[3]; - u32 sbadmatch3; /* address match3 */ - u32 PAD; - u32 sbadmatch2; /* address match2 */ - u32 PAD; - u32 sbadmatch1; /* address match1 */ - u32 PAD[7]; - u32 sbimstate; /* initiator agent state */ - u32 sbintvec; /* interrupt mask */ - u32 sbtmstatelow; /* target state */ - u32 sbtmstatehigh; /* target state */ - u32 sbbwa0; /* bandwidth allocation table0 */ - u32 PAD; - u32 sbimconfiglow; /* initiator configuration */ - u32 sbimconfighigh; /* initiator configuration */ - u32 sbadmatch0; /* address match0 */ - u32 PAD; - u32 sbtmconfiglow; /* target configuration */ - u32 sbtmconfighigh; /* target configuration */ - u32 sbbconfig; /* broadcast configuration */ - u32 PAD; - u32 sbbstate; /* broadcast state */ - u32 PAD[3]; - u32 sbactcnfg; /* activate configuration */ - u32 PAD[3]; - u32 sbflagst; /* current sbflags */ - u32 PAD[3]; - u32 sbidlow; /* identification */ - u32 sbidhigh; /* identification */ -} sbconfig_t; - -#endif /* _LANGUAGE_ASSEMBLY */ - -/* sbipsflag */ -#define SBIPS_INT1_MASK 0x3f /* which sbflags get routed to mips interrupt 1 */ -#define SBIPS_INT1_SHIFT 0 -#define SBIPS_INT2_MASK 0x3f00 /* which sbflags get routed to mips interrupt 2 */ -#define SBIPS_INT2_SHIFT 8 -#define SBIPS_INT3_MASK 0x3f0000 /* which sbflags get routed to mips interrupt 3 */ -#define SBIPS_INT3_SHIFT 16 -#define SBIPS_INT4_MASK 0x3f000000 /* which sbflags get routed to mips interrupt 4 */ -#define SBIPS_INT4_SHIFT 24 - -/* sbtpsflag */ -#define SBTPS_NUM0_MASK 0x3f /* interrupt sbFlag # generated by this core */ -#define SBTPS_F0EN0 0x40 /* interrupt is always sent on the backplane */ - -/* sbtmerrlog */ -#define SBTMEL_CM 0x00000007 /* command */ -#define SBTMEL_CI 0x0000ff00 /* connection id */ -#define SBTMEL_EC 0x0f000000 /* error code */ -#define SBTMEL_ME 0x80000000 /* multiple error */ - -/* sbimstate */ -#define SBIM_PC 0xf /* pipecount */ -#define SBIM_AP_MASK 0x30 /* arbitration policy */ -#define SBIM_AP_BOTH 0x00 /* use both timeslaces and token */ -#define SBIM_AP_TS 0x10 /* use timesliaces only */ -#define SBIM_AP_TK 0x20 /* use token only */ -#define SBIM_AP_RSV 0x30 /* reserved */ -#define SBIM_IBE 0x20000 /* inbanderror */ -#define SBIM_TO 0x40000 /* timeout */ -#define SBIM_BY 0x01800000 /* busy (sonics >= 2.3) */ -#define SBIM_RJ 0x02000000 /* reject (sonics >= 2.3) */ - -/* sbtmstatelow */ -#define SBTML_RESET 0x0001 /* reset */ -#define SBTML_REJ_MASK 0x0006 /* reject field */ -#define SBTML_REJ 0x0002 /* reject */ -#define SBTML_TMPREJ 0x0004 /* temporary reject, for error recovery */ - -#define SBTML_SICF_SHIFT 16 /* Shift to locate the SI control flags in sbtml */ - -/* sbtmstatehigh */ -#define SBTMH_SERR 0x0001 /* serror */ -#define SBTMH_INT 0x0002 /* interrupt */ -#define SBTMH_BUSY 0x0004 /* busy */ -#define SBTMH_TO 0x0020 /* timeout (sonics >= 2.3) */ - -#define SBTMH_SISF_SHIFT 16 /* Shift to locate the SI status flags in sbtmh */ - -/* sbbwa0 */ -#define SBBWA_TAB0_MASK 0xffff /* lookup table 0 */ -#define SBBWA_TAB1_MASK 0xffff /* lookup table 1 */ -#define SBBWA_TAB1_SHIFT 16 - -/* sbimconfiglow */ -#define SBIMCL_STO_MASK 0x7 /* service timeout */ -#define SBIMCL_RTO_MASK 0x70 /* request timeout */ -#define SBIMCL_RTO_SHIFT 4 -#define SBIMCL_CID_MASK 0xff0000 /* connection id */ -#define SBIMCL_CID_SHIFT 16 - -/* sbimconfighigh */ -#define SBIMCH_IEM_MASK 0xc /* inband error mode */ -#define SBIMCH_TEM_MASK 0x30 /* timeout error mode */ -#define SBIMCH_TEM_SHIFT 4 -#define SBIMCH_BEM_MASK 0xc0 /* bus error mode */ -#define SBIMCH_BEM_SHIFT 6 - -/* sbadmatch0 */ -#define SBAM_TYPE_MASK 0x3 /* address type */ -#define SBAM_AD64 0x4 /* reserved */ -#define SBAM_ADINT0_MASK 0xf8 /* type0 size */ -#define SBAM_ADINT0_SHIFT 3 -#define SBAM_ADINT1_MASK 0x1f8 /* type1 size */ -#define SBAM_ADINT1_SHIFT 3 -#define SBAM_ADINT2_MASK 0x1f8 /* type2 size */ -#define SBAM_ADINT2_SHIFT 3 -#define SBAM_ADEN 0x400 /* enable */ -#define SBAM_ADNEG 0x800 /* negative decode */ -#define SBAM_BASE0_MASK 0xffffff00 /* type0 base address */ -#define SBAM_BASE0_SHIFT 8 -#define SBAM_BASE1_MASK 0xfffff000 /* type1 base address for the core */ -#define SBAM_BASE1_SHIFT 12 -#define SBAM_BASE2_MASK 0xffff0000 /* type2 base address for the core */ -#define SBAM_BASE2_SHIFT 16 - -/* sbtmconfiglow */ -#define SBTMCL_CD_MASK 0xff /* clock divide */ -#define SBTMCL_CO_MASK 0xf800 /* clock offset */ -#define SBTMCL_CO_SHIFT 11 -#define SBTMCL_IF_MASK 0xfc0000 /* interrupt flags */ -#define SBTMCL_IF_SHIFT 18 -#define SBTMCL_IM_MASK 0x3000000 /* interrupt mode */ -#define SBTMCL_IM_SHIFT 24 - -/* sbtmconfighigh */ -#define SBTMCH_BM_MASK 0x3 /* busy mode */ -#define SBTMCH_RM_MASK 0x3 /* retry mode */ -#define SBTMCH_RM_SHIFT 2 -#define SBTMCH_SM_MASK 0x30 /* stop mode */ -#define SBTMCH_SM_SHIFT 4 -#define SBTMCH_EM_MASK 0x300 /* sb error mode */ -#define SBTMCH_EM_SHIFT 8 -#define SBTMCH_IM_MASK 0xc00 /* int mode */ -#define SBTMCH_IM_SHIFT 10 - -/* sbbconfig */ -#define SBBC_LAT_MASK 0x3 /* sb latency */ -#define SBBC_MAX0_MASK 0xf0000 /* maxccntr0 */ -#define SBBC_MAX0_SHIFT 16 -#define SBBC_MAX1_MASK 0xf00000 /* maxccntr1 */ -#define SBBC_MAX1_SHIFT 20 - -/* sbbstate */ -#define SBBS_SRD 0x1 /* st reg disable */ -#define SBBS_HRD 0x2 /* hold reg disable */ - -/* sbidlow */ -#define SBIDL_CS_MASK 0x3 /* config space */ -#define SBIDL_AR_MASK 0x38 /* # address ranges supported */ -#define SBIDL_AR_SHIFT 3 -#define SBIDL_SYNCH 0x40 /* sync */ -#define SBIDL_INIT 0x80 /* initiator */ -#define SBIDL_MINLAT_MASK 0xf00 /* minimum backplane latency */ -#define SBIDL_MINLAT_SHIFT 8 -#define SBIDL_MAXLAT 0xf000 /* maximum backplane latency */ -#define SBIDL_MAXLAT_SHIFT 12 -#define SBIDL_FIRST 0x10000 /* this initiator is first */ -#define SBIDL_CW_MASK 0xc0000 /* cycle counter width */ -#define SBIDL_CW_SHIFT 18 -#define SBIDL_TP_MASK 0xf00000 /* target ports */ -#define SBIDL_TP_SHIFT 20 -#define SBIDL_IP_MASK 0xf000000 /* initiator ports */ -#define SBIDL_IP_SHIFT 24 -#define SBIDL_RV_MASK 0xf0000000 /* sonics backplane revision code */ -#define SBIDL_RV_SHIFT 28 -#define SBIDL_RV_2_2 0x00000000 /* version 2.2 or earlier */ -#define SBIDL_RV_2_3 0x10000000 /* version 2.3 */ - -/* sbidhigh */ -#define SBIDH_RC_MASK 0x000f /* revision code */ -#define SBIDH_RCE_MASK 0x7000 /* revision code extension field */ -#define SBIDH_RCE_SHIFT 8 -#define SBCOREREV(sbidh) \ - ((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | ((sbidh) & SBIDH_RC_MASK)) -#define SBIDH_CC_MASK 0x8ff0 /* core code */ -#define SBIDH_CC_SHIFT 4 -#define SBIDH_VC_MASK 0xffff0000 /* vendor code */ -#define SBIDH_VC_SHIFT 16 - -#define SB_COMMIT 0xfd8 /* update buffered registers value */ - -/* vendor codes */ -#define SB_VEND_BCM 0x4243 /* Broadcom's SB vendor code */ #endif /* _SBCONFIG_H */ diff --git a/drivers/staging/brcm80211/include/sbdma.h b/drivers/staging/brcm80211/include/sbdma.h index 1da979a4d1d2..9814a0ce8feb 100644 --- a/drivers/staging/brcm80211/include/sbdma.h +++ b/drivers/staging/brcm80211/include/sbdma.h @@ -25,19 +25,6 @@ /* 32 bits addressing */ -/* dma registers per channel(xmt or rcv) */ -typedef volatile struct { - u32 control; /* enable, et al */ - u32 addr; /* descriptor ring base address (4K aligned) */ - u32 ptr; /* last descriptor posted to chip */ - u32 status; /* current active descriptor, et al */ -} dma32regs_t; - -typedef volatile struct { - dma32regs_t xmt; /* dma tx channel */ - dma32regs_t rcv; /* dma rx channel */ -} dma32regp_t; - typedef volatile struct { /* diag access */ u32 fifoaddr; /* diag address */ u32 fifodatalow; /* low 32bits of data */ @@ -45,115 +32,6 @@ typedef volatile struct { /* diag access */ u32 pad; /* reserved */ } dma32diag_t; -/* - * DMA Descriptor - * Descriptors are only read by the hardware, never written back. - */ -typedef volatile struct { - u32 ctrl; /* misc control bits & bufcount */ - u32 addr; /* data buffer address */ -} dma32dd_t; - -/* - * Each descriptor ring must be 4096byte aligned, and fit within a single 4096byte page. - */ -#define D32RINGALIGN_BITS 12 -#define D32MAXRINGSZ (1 << D32RINGALIGN_BITS) -#define D32RINGALIGN (1 << D32RINGALIGN_BITS) - -#define D32MAXDD (D32MAXRINGSZ / sizeof (dma32dd_t)) - -/* transmit channel control */ -#define XC_XE ((u32)1 << 0) /* transmit enable */ -#define XC_SE ((u32)1 << 1) /* transmit suspend request */ -#define XC_LE ((u32)1 << 2) /* loopback enable */ -#define XC_FL ((u32)1 << 4) /* flush request */ -#define XC_PD ((u32)1 << 11) /* parity check disable */ -#define XC_AE ((u32)3 << 16) /* address extension bits */ -#define XC_AE_SHIFT 16 - -/* transmit descriptor table pointer */ -#define XP_LD_MASK 0xfff /* last valid descriptor */ - -/* transmit channel status */ -#define XS_CD_MASK 0x0fff /* current descriptor pointer */ -#define XS_XS_MASK 0xf000 /* transmit state */ -#define XS_XS_SHIFT 12 -#define XS_XS_DISABLED 0x0000 /* disabled */ -#define XS_XS_ACTIVE 0x1000 /* active */ -#define XS_XS_IDLE 0x2000 /* idle wait */ -#define XS_XS_STOPPED 0x3000 /* stopped */ -#define XS_XS_SUSP 0x4000 /* suspend pending */ -#define XS_XE_MASK 0xf0000 /* transmit errors */ -#define XS_XE_SHIFT 16 -#define XS_XE_NOERR 0x00000 /* no error */ -#define XS_XE_DPE 0x10000 /* descriptor protocol error */ -#define XS_XE_DFU 0x20000 /* data fifo underrun */ -#define XS_XE_BEBR 0x30000 /* bus error on buffer read */ -#define XS_XE_BEDA 0x40000 /* bus error on descriptor access */ -#define XS_AD_MASK 0xfff00000 /* active descriptor */ -#define XS_AD_SHIFT 20 - -/* receive channel control */ -#define RC_RE ((u32)1 << 0) /* receive enable */ -#define RC_RO_MASK 0xfe /* receive frame offset */ -#define RC_RO_SHIFT 1 -#define RC_FM ((u32)1 << 8) /* direct fifo receive (pio) mode */ -#define RC_SH ((u32)1 << 9) /* separate rx header descriptor enable */ -#define RC_OC ((u32)1 << 10) /* overflow continue */ -#define RC_PD ((u32)1 << 11) /* parity check disable */ -#define RC_AE ((u32)3 << 16) /* address extension bits */ -#define RC_AE_SHIFT 16 - -/* receive descriptor table pointer */ -#define RP_LD_MASK 0xfff /* last valid descriptor */ - -/* receive channel status */ -#define RS_CD_MASK 0x0fff /* current descriptor pointer */ -#define RS_RS_MASK 0xf000 /* receive state */ -#define RS_RS_SHIFT 12 -#define RS_RS_DISABLED 0x0000 /* disabled */ -#define RS_RS_ACTIVE 0x1000 /* active */ -#define RS_RS_IDLE 0x2000 /* idle wait */ -#define RS_RS_STOPPED 0x3000 /* reserved */ -#define RS_RE_MASK 0xf0000 /* receive errors */ -#define RS_RE_SHIFT 16 -#define RS_RE_NOERR 0x00000 /* no error */ -#define RS_RE_DPE 0x10000 /* descriptor protocol error */ -#define RS_RE_DFO 0x20000 /* data fifo overflow */ -#define RS_RE_BEBW 0x30000 /* bus error on buffer write */ -#define RS_RE_BEDA 0x40000 /* bus error on descriptor access */ -#define RS_AD_MASK 0xfff00000 /* active descriptor */ -#define RS_AD_SHIFT 20 - -/* fifoaddr */ -#define FA_OFF_MASK 0xffff /* offset */ -#define FA_SEL_MASK 0xf0000 /* select */ -#define FA_SEL_SHIFT 16 -#define FA_SEL_XDD 0x00000 /* transmit dma data */ -#define FA_SEL_XDP 0x10000 /* transmit dma pointers */ -#define FA_SEL_RDD 0x40000 /* receive dma data */ -#define FA_SEL_RDP 0x50000 /* receive dma pointers */ -#define FA_SEL_XFD 0x80000 /* transmit fifo data */ -#define FA_SEL_XFP 0x90000 /* transmit fifo pointers */ -#define FA_SEL_RFD 0xc0000 /* receive fifo data */ -#define FA_SEL_RFP 0xd0000 /* receive fifo pointers */ -#define FA_SEL_RSD 0xe0000 /* receive frame status data */ -#define FA_SEL_RSP 0xf0000 /* receive frame status pointers */ - -/* descriptor control flags */ -#define CTRL_BC_MASK 0x00001fff /* buffer byte count, real data len must <= 4KB */ -#define CTRL_AE ((u32)3 << 16) /* address extension bits */ -#define CTRL_AE_SHIFT 16 -#define CTRL_PARITY ((u32)3 << 18) /* parity bit */ -#define CTRL_EOT ((u32)1 << 28) /* end of descriptor table */ -#define CTRL_IOC ((u32)1 << 29) /* interrupt on completion */ -#define CTRL_EOF ((u32)1 << 30) /* end of frame */ -#define CTRL_SOF ((u32)1 << 31) /* start of frame */ - -/* control flags in the range [27:20] are core-specific and not defined here */ -#define CTRL_CORE_MASK 0x0ff00000 - /* 64 bits addressing */ /* dma registers per channel(xmt or rcv) */ @@ -166,150 +44,4 @@ typedef volatile struct { u32 status1; /* active descriptor, xmt error */ } dma64regs_t; -typedef volatile struct { - dma64regs_t tx; /* dma64 tx channel */ - dma64regs_t rx; /* dma64 rx channel */ -} dma64regp_t; - -typedef volatile struct { /* diag access */ - u32 fifoaddr; /* diag address */ - u32 fifodatalow; /* low 32bits of data */ - u32 fifodatahigh; /* high 32bits of data */ - u32 pad; /* reserved */ -} dma64diag_t; - -/* - * DMA Descriptor - * Descriptors are only read by the hardware, never written back. - */ -typedef volatile struct { - u32 ctrl1; /* misc control bits & bufcount */ - u32 ctrl2; /* buffer count and address extension */ - u32 addrlow; /* memory address of the date buffer, bits 31:0 */ - u32 addrhigh; /* memory address of the date buffer, bits 63:32 */ -} dma64dd_t; - -/* - * Each descriptor ring must be 8kB aligned, and fit within a contiguous 8kB physical address. - */ -#define D64RINGALIGN_BITS 13 -#define D64MAXRINGSZ (1 << D64RINGALIGN_BITS) -#define D64RINGALIGN (1 << D64RINGALIGN_BITS) - -#define D64MAXDD (D64MAXRINGSZ / sizeof (dma64dd_t)) - -/* transmit channel control */ -#define D64_XC_XE 0x00000001 /* transmit enable */ -#define D64_XC_SE 0x00000002 /* transmit suspend request */ -#define D64_XC_LE 0x00000004 /* loopback enable */ -#define D64_XC_FL 0x00000010 /* flush request */ -#define D64_XC_PD 0x00000800 /* parity check disable */ -#define D64_XC_AE 0x00030000 /* address extension bits */ -#define D64_XC_AE_SHIFT 16 - -/* transmit descriptor table pointer */ -#define D64_XP_LD_MASK 0x00000fff /* last valid descriptor */ - -/* transmit channel status */ -#define D64_XS0_CD_MASK 0x00001fff /* current descriptor pointer */ -#define D64_XS0_XS_MASK 0xf0000000 /* transmit state */ -#define D64_XS0_XS_SHIFT 28 -#define D64_XS0_XS_DISABLED 0x00000000 /* disabled */ -#define D64_XS0_XS_ACTIVE 0x10000000 /* active */ -#define D64_XS0_XS_IDLE 0x20000000 /* idle wait */ -#define D64_XS0_XS_STOPPED 0x30000000 /* stopped */ -#define D64_XS0_XS_SUSP 0x40000000 /* suspend pending */ - -#define D64_XS1_AD_MASK 0x00001fff /* active descriptor */ -#define D64_XS1_XE_MASK 0xf0000000 /* transmit errors */ -#define D64_XS1_XE_SHIFT 28 -#define D64_XS1_XE_NOERR 0x00000000 /* no error */ -#define D64_XS1_XE_DPE 0x10000000 /* descriptor protocol error */ -#define D64_XS1_XE_DFU 0x20000000 /* data fifo underrun */ -#define D64_XS1_XE_DTE 0x30000000 /* data transfer error */ -#define D64_XS1_XE_DESRE 0x40000000 /* descriptor read error */ -#define D64_XS1_XE_COREE 0x50000000 /* core error */ - -/* receive channel control */ -#define D64_RC_RE 0x00000001 /* receive enable */ -#define D64_RC_RO_MASK 0x000000fe /* receive frame offset */ -#define D64_RC_RO_SHIFT 1 -#define D64_RC_FM 0x00000100 /* direct fifo receive (pio) mode */ -#define D64_RC_SH 0x00000200 /* separate rx header descriptor enable */ -#define D64_RC_OC 0x00000400 /* overflow continue */ -#define D64_RC_PD 0x00000800 /* parity check disable */ -#define D64_RC_AE 0x00030000 /* address extension bits */ -#define D64_RC_AE_SHIFT 16 - -/* flags for dma controller */ -#define DMA_CTRL_PEN (1 << 0) /* partity enable */ -#define DMA_CTRL_ROC (1 << 1) /* rx overflow continue */ -#define DMA_CTRL_RXMULTI (1 << 2) /* allow rx scatter to multiple descriptors */ -#define DMA_CTRL_UNFRAMED (1 << 3) /* Unframed Rx/Tx data */ - -/* receive descriptor table pointer */ -#define D64_RP_LD_MASK 0x00000fff /* last valid descriptor */ - -/* receive channel status */ -#define D64_RS0_CD_MASK 0x00001fff /* current descriptor pointer */ -#define D64_RS0_RS_MASK 0xf0000000 /* receive state */ -#define D64_RS0_RS_SHIFT 28 -#define D64_RS0_RS_DISABLED 0x00000000 /* disabled */ -#define D64_RS0_RS_ACTIVE 0x10000000 /* active */ -#define D64_RS0_RS_IDLE 0x20000000 /* idle wait */ -#define D64_RS0_RS_STOPPED 0x30000000 /* stopped */ -#define D64_RS0_RS_SUSP 0x40000000 /* suspend pending */ - -#define D64_RS1_AD_MASK 0x0001ffff /* active descriptor */ -#define D64_RS1_RE_MASK 0xf0000000 /* receive errors */ -#define D64_RS1_RE_SHIFT 28 -#define D64_RS1_RE_NOERR 0x00000000 /* no error */ -#define D64_RS1_RE_DPO 0x10000000 /* descriptor protocol error */ -#define D64_RS1_RE_DFU 0x20000000 /* data fifo overflow */ -#define D64_RS1_RE_DTE 0x30000000 /* data transfer error */ -#define D64_RS1_RE_DESRE 0x40000000 /* descriptor read error */ -#define D64_RS1_RE_COREE 0x50000000 /* core error */ - -/* fifoaddr */ -#define D64_FA_OFF_MASK 0xffff /* offset */ -#define D64_FA_SEL_MASK 0xf0000 /* select */ -#define D64_FA_SEL_SHIFT 16 -#define D64_FA_SEL_XDD 0x00000 /* transmit dma data */ -#define D64_FA_SEL_XDP 0x10000 /* transmit dma pointers */ -#define D64_FA_SEL_RDD 0x40000 /* receive dma data */ -#define D64_FA_SEL_RDP 0x50000 /* receive dma pointers */ -#define D64_FA_SEL_XFD 0x80000 /* transmit fifo data */ -#define D64_FA_SEL_XFP 0x90000 /* transmit fifo pointers */ -#define D64_FA_SEL_RFD 0xc0000 /* receive fifo data */ -#define D64_FA_SEL_RFP 0xd0000 /* receive fifo pointers */ -#define D64_FA_SEL_RSD 0xe0000 /* receive frame status data */ -#define D64_FA_SEL_RSP 0xf0000 /* receive frame status pointers */ - -/* descriptor control flags 1 */ -#define D64_CTRL_COREFLAGS 0x0ff00000 /* core specific flags */ -#define D64_CTRL1_EOT ((u32)1 << 28) /* end of descriptor table */ -#define D64_CTRL1_IOC ((u32)1 << 29) /* interrupt on completion */ -#define D64_CTRL1_EOF ((u32)1 << 30) /* end of frame */ -#define D64_CTRL1_SOF ((u32)1 << 31) /* start of frame */ - -/* descriptor control flags 2 */ -#define D64_CTRL2_BC_MASK 0x00007fff /* buffer byte count. real data len must <= 16KB */ -#define D64_CTRL2_AE 0x00030000 /* address extension bits */ -#define D64_CTRL2_AE_SHIFT 16 -#define D64_CTRL2_PARITY 0x00040000 /* parity bit */ - -/* control flags in the range [27:20] are core-specific and not defined here */ -#define D64_CTRL_CORE_MASK 0x0ff00000 - -#define D64_RX_FRM_STS_LEN 0x0000ffff /* frame length mask */ -#define D64_RX_FRM_STS_OVFL 0x00800000 /* RxOverFlow */ -#define D64_RX_FRM_STS_DSCRCNT 0x0f000000 /* no. of descriptors used - 1 */ -#define D64_RX_FRM_STS_DATATYPE 0xf0000000 /* core-dependent data type */ - -/* receive frame status */ -typedef volatile struct { - u16 len; - u16 flags; -} dma_rxh_t; - #endif /* _sbdma_h_ */ diff --git a/drivers/staging/brcm80211/include/sbsdio.h b/drivers/staging/brcm80211/include/sbsdio.h deleted file mode 100644 index c7facd3795a0..000000000000 --- a/drivers/staging/brcm80211/include/sbsdio.h +++ /dev/null @@ -1,152 +0,0 @@ -/* - * Copyright (c) 2010 Broadcom Corporation - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES - * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY - * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES - * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION - * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN - * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. - */ - -#ifndef _SBSDIO_H -#define _SBSDIO_H - -#define SBSDIO_NUM_FUNCTION 3 /* as of sdiod rev 0, supports 3 functions */ - -/* function 1 miscellaneous registers */ -#define SBSDIO_SPROM_CS 0x10000 /* sprom command and status */ -#define SBSDIO_SPROM_INFO 0x10001 /* sprom info register */ -#define SBSDIO_SPROM_DATA_LOW 0x10002 /* sprom indirect access data byte 0 */ -#define SBSDIO_SPROM_DATA_HIGH 0x10003 /* sprom indirect access data byte 1 */ -#define SBSDIO_SPROM_ADDR_LOW 0x10004 /* sprom indirect access addr byte 0 */ -#define SBSDIO_SPROM_ADDR_HIGH 0x10005 /* sprom indirect access addr byte 0 */ -#define SBSDIO_CHIP_CTRL_DATA 0x10006 /* xtal_pu (gpio) output */ -#define SBSDIO_CHIP_CTRL_EN 0x10007 /* xtal_pu (gpio) enable */ -#define SBSDIO_WATERMARK 0x10008 /* rev < 7, watermark for sdio device */ -#define SBSDIO_DEVICE_CTL 0x10009 /* control busy signal generation */ - -/* registers introduced in rev 8, some content (mask/bits) defs in sbsdpcmdev.h */ -#define SBSDIO_FUNC1_SBADDRLOW 0x1000A /* SB Address Window Low (b15) */ -#define SBSDIO_FUNC1_SBADDRMID 0x1000B /* SB Address Window Mid (b23:b16) */ -#define SBSDIO_FUNC1_SBADDRHIGH 0x1000C /* SB Address Window High (b31:b24) */ -#define SBSDIO_FUNC1_FRAMECTRL 0x1000D /* Frame Control (frame term/abort) */ -#define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E /* ChipClockCSR (ALP/HT ctl/status) */ -#define SBSDIO_FUNC1_SDIOPULLUP 0x1000F /* SdioPullUp (on cmd, d0-d2) */ -#define SBSDIO_FUNC1_WFRAMEBCLO 0x10019 /* Write Frame Byte Count Low */ -#define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A /* Write Frame Byte Count High */ -#define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B /* Read Frame Byte Count Low */ -#define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C /* Read Frame Byte Count High */ - -#define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */ -#define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001C /* f1 misc register end */ - -/* SBSDIO_SPROM_CS */ -#define SBSDIO_SPROM_IDLE 0 -#define SBSDIO_SPROM_WRITE 1 -#define SBSDIO_SPROM_READ 2 -#define SBSDIO_SPROM_WEN 4 -#define SBSDIO_SPROM_WDS 7 -#define SBSDIO_SPROM_DONE 8 - -/* SBSDIO_SPROM_INFO */ -#define SROM_SZ_MASK 0x03 /* SROM size, 1: 4k, 2: 16k */ -#define SROM_BLANK 0x04 /* depreciated in corerev 6 */ -#define SROM_OTP 0x80 /* OTP present */ - -/* SBSDIO_CHIP_CTRL */ -#define SBSDIO_CHIP_CTRL_XTAL 0x01 /* or'd with onchip xtal_pu, - * 1: power on oscillator - * (for 4318 only) - */ -/* SBSDIO_WATERMARK */ -#define SBSDIO_WATERMARK_MASK 0x7f /* number of words - 1 for sd device - * to wait before sending data to host - */ - -/* SBSDIO_DEVICE_CTL */ -#define SBSDIO_DEVCTL_SETBUSY 0x01 /* 1: device will assert busy signal when - * receiving CMD53 - */ -#define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 /* 1: assertion of sdio interrupt is - * synchronous to the sdio clock - */ -#define SBSDIO_DEVCTL_CA_INT_ONLY 0x04 /* 1: mask all interrupts to host - * except the chipActive (rev 8) - */ -#define SBSDIO_DEVCTL_PADS_ISO 0x08 /* 1: isolate internal sdio signals, put - * external pads in tri-state; requires - * sdio bus power cycle to clear (rev 9) - */ -#define SBSDIO_DEVCTL_SB_RST_CTL 0x30 /* Force SD->SB reset mapping (rev 11) */ -#define SBSDIO_DEVCTL_RST_CORECTL 0x00 /* Determined by CoreControl bit */ -#define SBSDIO_DEVCTL_RST_BPRESET 0x10 /* Force backplane reset */ -#define SBSDIO_DEVCTL_RST_NOBPRESET 0x20 /* Force no backplane reset */ - -/* SBSDIO_FUNC1_CHIPCLKCSR */ -#define SBSDIO_FORCE_ALP 0x01 /* Force ALP request to backplane */ -#define SBSDIO_FORCE_HT 0x02 /* Force HT request to backplane */ -#define SBSDIO_FORCE_ILP 0x04 /* Force ILP request to backplane */ -#define SBSDIO_ALP_AVAIL_REQ 0x08 /* Make ALP ready (power up xtal) */ -#define SBSDIO_HT_AVAIL_REQ 0x10 /* Make HT ready (power up PLL) */ -#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20 /* Squelch clock requests from HW */ -#define SBSDIO_ALP_AVAIL 0x40 /* Status: ALP is ready */ -#define SBSDIO_HT_AVAIL 0x80 /* Status: HT is ready */ -/* In rev8, actual avail bits followed original docs */ -#define SBSDIO_Rev8_HT_AVAIL 0x40 -#define SBSDIO_Rev8_ALP_AVAIL 0x80 - -#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL) -#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS) -#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS) -#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval)) -#define SBSDIO_CLKAV(regval, alponly) (SBSDIO_ALPAV(regval) && \ - (alponly ? 1 : SBSDIO_HTAV(regval))) - -/* SBSDIO_FUNC1_SDIOPULLUP */ -#define SBSDIO_PULLUP_D0 0x01 /* Enable D0/MISO pullup */ -#define SBSDIO_PULLUP_D1 0x02 /* Enable D1/INT# pullup */ -#define SBSDIO_PULLUP_D2 0x04 /* Enable D2 pullup */ -#define SBSDIO_PULLUP_CMD 0x08 /* Enable CMD/MOSI pullup */ -#define SBSDIO_PULLUP_ALL 0x0f /* All valid bits */ - -/* function 1 OCP space */ -#define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF /* sb offset addr is <= 15 bits, 32k */ -#define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000 -#define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 /* with b15, maps to 32-bit SB access */ - -/* some duplication with sbsdpcmdev.h here */ -/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */ -#define SBSDIO_SBADDRLOW_MASK 0x80 /* Valid bits in SBADDRLOW */ -#define SBSDIO_SBADDRMID_MASK 0xff /* Valid bits in SBADDRMID */ -#define SBSDIO_SBADDRHIGH_MASK 0xffU /* Valid bits in SBADDRHIGH */ -#define SBSDIO_SBWINDOW_MASK 0xffff8000 /* Address bits from SBADDR regs */ - -/* direct(mapped) cis space */ -#define SBSDIO_CIS_BASE_COMMON 0x1000 /* MAPPED common CIS address */ -#define SBSDIO_CIS_SIZE_LIMIT 0x200 /* maximum bytes in one CIS */ -#define SBSDIO_OTP_CIS_SIZE_LIMIT 0x078 /* maximum bytes OTP CIS */ - -#define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF /* cis offset addr is < 17 bits */ - -#define SBSDIO_CIS_MANFID_TUPLE_LEN 6 /* manfid tuple length, include tuple, - * link bytes - */ - -/* indirect cis access (in sprom) */ -#define SBSDIO_SPROM_CIS_OFFSET 0x8 /* 8 control bytes first, CIS starts from - * 8th byte - */ - -#define SBSDIO_BYTEMODE_DATALEN_MAX 64 /* sdio byte mode: maximum length of one - * data command - */ - -#define SBSDIO_CORE_ADDR_MASK 0x1FFFF /* sdio core function one address mask */ - -#endif /* _SBSDIO_H */ diff --git a/drivers/staging/brcm80211/include/sbsdpcmdev.h b/drivers/staging/brcm80211/include/sbsdpcmdev.h deleted file mode 100644 index afd35811d4a5..000000000000 --- a/drivers/staging/brcm80211/include/sbsdpcmdev.h +++ /dev/null @@ -1,281 +0,0 @@ -/* - * Copyright (c) 2010 Broadcom Corporation - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES - * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY - * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES - * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION - * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN - * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. - */ - -#ifndef _sbsdpcmdev_h_ -#define _sbsdpcmdev_h_ - -/* cpp contortions to concatenate w/arg prescan */ -#ifndef PAD -#define _PADLINE(line) pad ## line -#define _XSTR(line) _PADLINE(line) -#define PAD _XSTR(__LINE__) -#endif /* PAD */ - -typedef volatile struct { - dma64regs_t xmt; /* dma tx */ - u32 PAD[2]; - dma64regs_t rcv; /* dma rx */ - u32 PAD[2]; -} dma64p_t; - -/* dma64 sdiod corerev >= 1 */ -typedef volatile struct { - dma64p_t dma64regs[2]; - dma64diag_t dmafifo; /* DMA Diagnostic Regs, 0x280-0x28c */ - u32 PAD[92]; -} sdiodma64_t; - -/* dma32 sdiod corerev == 0 */ -typedef volatile struct { - dma32regp_t dma32regs[2]; /* dma tx & rx, 0x200-0x23c */ - dma32diag_t dmafifo; /* DMA Diagnostic Regs, 0x240-0x24c */ - u32 PAD[108]; -} sdiodma32_t; - -/* dma32 regs for pcmcia core */ -typedef volatile struct { - dma32regp_t dmaregs; /* DMA Regs, 0x200-0x21c, rev8 */ - dma32diag_t dmafifo; /* DMA Diagnostic Regs, 0x220-0x22c */ - u32 PAD[116]; -} pcmdma32_t; - -/* core registers */ -typedef volatile struct { - u32 corecontrol; /* CoreControl, 0x000, rev8 */ - u32 corestatus; /* CoreStatus, 0x004, rev8 */ - u32 PAD[1]; - u32 biststatus; /* BistStatus, 0x00c, rev8 */ - - /* PCMCIA access */ - u16 pcmciamesportaladdr; /* PcmciaMesPortalAddr, 0x010, rev8 */ - u16 PAD[1]; - u16 pcmciamesportalmask; /* PcmciaMesPortalMask, 0x014, rev8 */ - u16 PAD[1]; - u16 pcmciawrframebc; /* PcmciaWrFrameBC, 0x018, rev8 */ - u16 PAD[1]; - u16 pcmciaunderflowtimer; /* PcmciaUnderflowTimer, 0x01c, rev8 */ - u16 PAD[1]; - - /* interrupt */ - u32 intstatus; /* IntStatus, 0x020, rev8 */ - u32 hostintmask; /* IntHostMask, 0x024, rev8 */ - u32 intmask; /* IntSbMask, 0x028, rev8 */ - u32 sbintstatus; /* SBIntStatus, 0x02c, rev8 */ - u32 sbintmask; /* SBIntMask, 0x030, rev8 */ - u32 funcintmask; /* SDIO Function Interrupt Mask, SDIO rev4 */ - u32 PAD[2]; - u32 tosbmailbox; /* ToSBMailbox, 0x040, rev8 */ - u32 tohostmailbox; /* ToHostMailbox, 0x044, rev8 */ - u32 tosbmailboxdata; /* ToSbMailboxData, 0x048, rev8 */ - u32 tohostmailboxdata; /* ToHostMailboxData, 0x04c, rev8 */ - - /* synchronized access to registers in SDIO clock domain */ - u32 sdioaccess; /* SdioAccess, 0x050, rev8 */ - u32 PAD[3]; - - /* PCMCIA frame control */ - u8 pcmciaframectrl; /* pcmciaFrameCtrl, 0x060, rev8 */ - u8 PAD[3]; - u8 pcmciawatermark; /* pcmciaWaterMark, 0x064, rev8 */ - u8 PAD[155]; - - /* interrupt batching control */ - u32 intrcvlazy; /* IntRcvLazy, 0x100, rev8 */ - u32 PAD[3]; - - /* counters */ - u32 cmd52rd; /* Cmd52RdCount, 0x110, rev8, SDIO: cmd52 reads */ - u32 cmd52wr; /* Cmd52WrCount, 0x114, rev8, SDIO: cmd52 writes */ - u32 cmd53rd; /* Cmd53RdCount, 0x118, rev8, SDIO: cmd53 reads */ - u32 cmd53wr; /* Cmd53WrCount, 0x11c, rev8, SDIO: cmd53 writes */ - u32 abort; /* AbortCount, 0x120, rev8, SDIO: aborts */ - u32 datacrcerror; /* DataCrcErrorCount, 0x124, rev8, SDIO: frames w/bad CRC */ - u32 rdoutofsync; /* RdOutOfSyncCount, 0x128, rev8, SDIO/PCMCIA: Rd Frm OOS */ - u32 wroutofsync; /* RdOutOfSyncCount, 0x12c, rev8, SDIO/PCMCIA: Wr Frm OOS */ - u32 writebusy; /* WriteBusyCount, 0x130, rev8, SDIO: dev asserted "busy" */ - u32 readwait; /* ReadWaitCount, 0x134, rev8, SDIO: read: no data avail */ - u32 readterm; /* ReadTermCount, 0x138, rev8, SDIO: rd frm terminates */ - u32 writeterm; /* WriteTermCount, 0x13c, rev8, SDIO: wr frm terminates */ - u32 PAD[40]; - u32 clockctlstatus; /* ClockCtlStatus, 0x1e0, rev8 */ - u32 PAD[7]; - - /* DMA engines */ - volatile union { - pcmdma32_t pcm32; - sdiodma32_t sdiod32; - sdiodma64_t sdiod64; - } dma; - - /* SDIO/PCMCIA CIS region */ - char cis[512]; /* 512 byte CIS, 0x400-0x5ff, rev6 */ - - /* PCMCIA function control registers */ - char pcmciafcr[256]; /* PCMCIA FCR, 0x600-6ff, rev6 */ - u16 PAD[55]; - - /* PCMCIA backplane access */ - u16 backplanecsr; /* BackplaneCSR, 0x76E, rev6 */ - u16 backplaneaddr0; /* BackplaneAddr0, 0x770, rev6 */ - u16 backplaneaddr1; /* BackplaneAddr1, 0x772, rev6 */ - u16 backplaneaddr2; /* BackplaneAddr2, 0x774, rev6 */ - u16 backplaneaddr3; /* BackplaneAddr3, 0x776, rev6 */ - u16 backplanedata0; /* BackplaneData0, 0x778, rev6 */ - u16 backplanedata1; /* BackplaneData1, 0x77a, rev6 */ - u16 backplanedata2; /* BackplaneData2, 0x77c, rev6 */ - u16 backplanedata3; /* BackplaneData3, 0x77e, rev6 */ - u16 PAD[31]; - - /* sprom "size" & "blank" info */ - u16 spromstatus; /* SPROMStatus, 0x7BE, rev2 */ - u32 PAD[464]; - - /* Sonics SiliconBackplane registers */ - sbconfig_t sbconfig; /* SbConfig Regs, 0xf00-0xfff, rev8 */ -} sdpcmd_regs_t; - -/* corecontrol */ -#define CC_CISRDY (1 << 0) /* CIS Ready */ -#define CC_BPRESEN (1 << 1) /* CCCR RES signal causes backplane reset */ -#define CC_F2RDY (1 << 2) /* set CCCR IOR2 bit */ -#define CC_CLRPADSISO (1 << 3) /* clear SDIO pads isolation bit (rev 11) */ -#define CC_XMTDATAAVAIL_MODE (1 << 4) /* data avail generates an interrupt */ -#define CC_XMTDATAAVAIL_CTRL (1 << 5) /* data avail interrupt ctrl */ - -/* corestatus */ -#define CS_PCMCIAMODE (1 << 0) /* Device Mode; 0=SDIO, 1=PCMCIA */ -#define CS_SMARTDEV (1 << 1) /* 1=smartDev enabled */ -#define CS_F2ENABLED (1 << 2) /* 1=host has enabled the device */ - -#define PCMCIA_MES_PA_MASK 0x7fff /* PCMCIA Message Portal Address Mask */ -#define PCMCIA_MES_PM_MASK 0x7fff /* PCMCIA Message Portal Mask Mask */ -#define PCMCIA_WFBC_MASK 0xffff /* PCMCIA Write Frame Byte Count Mask */ -#define PCMCIA_UT_MASK 0x07ff /* PCMCIA Underflow Timer Mask */ - -/* intstatus */ -#define I_SMB_SW0 (1 << 0) /* To SB Mail S/W interrupt 0 */ -#define I_SMB_SW1 (1 << 1) /* To SB Mail S/W interrupt 1 */ -#define I_SMB_SW2 (1 << 2) /* To SB Mail S/W interrupt 2 */ -#define I_SMB_SW3 (1 << 3) /* To SB Mail S/W interrupt 3 */ -#define I_SMB_SW_MASK 0x0000000f /* To SB Mail S/W interrupts mask */ -#define I_SMB_SW_SHIFT 0 /* To SB Mail S/W interrupts shift */ -#define I_HMB_SW0 (1 << 4) /* To Host Mail S/W interrupt 0 */ -#define I_HMB_SW1 (1 << 5) /* To Host Mail S/W interrupt 1 */ -#define I_HMB_SW2 (1 << 6) /* To Host Mail S/W interrupt 2 */ -#define I_HMB_SW3 (1 << 7) /* To Host Mail S/W interrupt 3 */ -#define I_HMB_SW_MASK 0x000000f0 /* To Host Mail S/W interrupts mask */ -#define I_HMB_SW_SHIFT 4 /* To Host Mail S/W interrupts shift */ -#define I_WR_OOSYNC (1 << 8) /* Write Frame Out Of Sync */ -#define I_RD_OOSYNC (1 << 9) /* Read Frame Out Of Sync */ -#define I_PC (1 << 10) /* descriptor error */ -#define I_PD (1 << 11) /* data error */ -#define I_DE (1 << 12) /* Descriptor protocol Error */ -#define I_RU (1 << 13) /* Receive descriptor Underflow */ -#define I_RO (1 << 14) /* Receive fifo Overflow */ -#define I_XU (1 << 15) /* Transmit fifo Underflow */ -#define I_RI (1 << 16) /* Receive Interrupt */ -#define I_BUSPWR (1 << 17) /* SDIO Bus Power Change (rev 9) */ -#define I_XMTDATA_AVAIL (1 << 23) /* bits in fifo */ -#define I_XI (1 << 24) /* Transmit Interrupt */ -#define I_RF_TERM (1 << 25) /* Read Frame Terminate */ -#define I_WF_TERM (1 << 26) /* Write Frame Terminate */ -#define I_PCMCIA_XU (1 << 27) /* PCMCIA Transmit FIFO Underflow */ -#define I_SBINT (1 << 28) /* sbintstatus Interrupt */ -#define I_CHIPACTIVE (1 << 29) /* chip transitioned from doze to active state */ -#define I_SRESET (1 << 30) /* CCCR RES interrupt */ -#define I_IOE2 (1U << 31) /* CCCR IOE2 Bit Changed */ -#define I_ERRORS (I_PC | I_PD | I_DE | I_RU | I_RO | I_XU) /* DMA Errors */ -#define I_DMA (I_RI | I_XI | I_ERRORS) - -/* sbintstatus */ -#define I_SB_SERR (1 << 8) /* Backplane SError (write) */ -#define I_SB_RESPERR (1 << 9) /* Backplane Response Error (read) */ -#define I_SB_SPROMERR (1 << 10) /* Error accessing the sprom */ - -/* sdioaccess */ -#define SDA_DATA_MASK 0x000000ff /* Read/Write Data Mask */ -#define SDA_ADDR_MASK 0x000fff00 /* Read/Write Address Mask */ -#define SDA_ADDR_SHIFT 8 /* Read/Write Address Shift */ -#define SDA_WRITE 0x01000000 /* Write bit */ -#define SDA_READ 0x00000000 /* Write bit cleared for Read */ -#define SDA_BUSY 0x80000000 /* Busy bit */ - -/* sdioaccess-accessible register address spaces */ -#define SDA_CCCR_SPACE 0x000 /* sdioAccess CCCR register space */ -#define SDA_F1_FBR_SPACE 0x100 /* sdioAccess F1 FBR register space */ -#define SDA_F2_FBR_SPACE 0x200 /* sdioAccess F2 FBR register space */ -#define SDA_F1_REG_SPACE 0x300 /* sdioAccess F1 core-specific register space */ - -/* SDA_F1_REG_SPACE sdioaccess-accessible F1 reg space register offsets */ -#define SDA_CHIPCONTROLDATA 0x006 /* ChipControlData */ -#define SDA_CHIPCONTROLENAB 0x007 /* ChipControlEnable */ -#define SDA_F2WATERMARK 0x008 /* Function 2 Watermark */ -#define SDA_DEVICECONTROL 0x009 /* DeviceControl */ -#define SDA_SBADDRLOW 0x00a /* SbAddrLow */ -#define SDA_SBADDRMID 0x00b /* SbAddrMid */ -#define SDA_SBADDRHIGH 0x00c /* SbAddrHigh */ -#define SDA_FRAMECTRL 0x00d /* FrameCtrl */ -#define SDA_CHIPCLOCKCSR 0x00e /* ChipClockCSR */ -#define SDA_SDIOPULLUP 0x00f /* SdioPullUp */ -#define SDA_SDIOWRFRAMEBCLOW 0x019 /* SdioWrFrameBCLow */ -#define SDA_SDIOWRFRAMEBCHIGH 0x01a /* SdioWrFrameBCHigh */ -#define SDA_SDIORDFRAMEBCLOW 0x01b /* SdioRdFrameBCLow */ -#define SDA_SDIORDFRAMEBCHIGH 0x01c /* SdioRdFrameBCHigh */ - -/* SDA_F2WATERMARK */ -#define SDA_F2WATERMARK_MASK 0x7f /* F2Watermark Mask */ - -/* SDA_SBADDRLOW */ -#define SDA_SBADDRLOW_MASK 0x80 /* SbAddrLow Mask */ - -/* SDA_SBADDRMID */ -#define SDA_SBADDRMID_MASK 0xff /* SbAddrMid Mask */ - -/* SDA_SBADDRHIGH */ -#define SDA_SBADDRHIGH_MASK 0xff /* SbAddrHigh Mask */ - -/* SDA_FRAMECTRL */ -#define SFC_RF_TERM (1 << 0) /* Read Frame Terminate */ -#define SFC_WF_TERM (1 << 1) /* Write Frame Terminate */ -#define SFC_CRC4WOOS (1 << 2) /* HW reports CRC error for write out of sync */ -#define SFC_ABORTALL (1 << 3) /* Abort cancels all in-progress frames */ - -/* pcmciaframectrl */ -#define PFC_RF_TERM (1 << 0) /* Read Frame Terminate */ -#define PFC_WF_TERM (1 << 1) /* Write Frame Terminate */ - -/* intrcvlazy */ -#define IRL_TO_MASK 0x00ffffff /* timeout */ -#define IRL_FC_MASK 0xff000000 /* frame count */ -#define IRL_FC_SHIFT 24 /* frame count */ - -/* rx header */ -typedef volatile struct { - u16 len; - u16 flags; -} sdpcmd_rxh_t; - -/* rx header flags */ -#define RXF_CRC 0x0001 /* CRC error detected */ -#define RXF_WOOS 0x0002 /* write frame out of sync */ -#define RXF_WF_TERM 0x0004 /* write frame terminated */ -#define RXF_ABORT 0x0008 /* write frame aborted */ -#define RXF_DISCARD (RXF_CRC | RXF_WOOS | RXF_WF_TERM | RXF_ABORT) /* bad frame */ - -/* HW frame tag */ -#define SDPCM_FRAMETAG_LEN 4 /* HW frametag: 2 bytes len, 2 bytes check val */ - -#endif /* _sbsdpcmdev_h_ */ diff --git a/drivers/staging/brcm80211/include/sdio.h b/drivers/staging/brcm80211/include/sdio.h deleted file mode 100644 index 670e379b9aac..000000000000 --- a/drivers/staging/brcm80211/include/sdio.h +++ /dev/null @@ -1,552 +0,0 @@ -/* - * Copyright (c) 2010 Broadcom Corporation - * - * Permission to use, copy, modify, and/or distribute this software for any - * purpose with or without fee is hereby granted, provided that the above - * copyright notice and this permission notice appear in all copies. - * - * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES - * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY - * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES - * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION - * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN - * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. - */ - -#ifndef _SDIO_H -#define _SDIO_H - -#ifdef BCMSDIO - -/* CCCR structure for function 0 */ -typedef volatile struct { - u8 cccr_sdio_rev; /* RO, cccr and sdio revision */ - u8 sd_rev; /* RO, sd spec revision */ - u8 io_en; /* I/O enable */ - u8 io_rdy; /* I/O ready reg */ - u8 intr_ctl; /* Master and per function interrupt enable control */ - u8 intr_status; /* RO, interrupt pending status */ - u8 io_abort; /* read/write abort or reset all functions */ - u8 bus_inter; /* bus interface control */ - u8 capability; /* RO, card capability */ - - u8 cis_base_low; /* 0x9 RO, common CIS base address, LSB */ - u8 cis_base_mid; - u8 cis_base_high; /* 0xB RO, common CIS base address, MSB */ - - /* suspend/resume registers */ - u8 bus_suspend; /* 0xC */ - u8 func_select; /* 0xD */ - u8 exec_flag; /* 0xE */ - u8 ready_flag; /* 0xF */ - - u8 fn0_blk_size[2]; /* 0x10(LSB), 0x11(MSB) */ - - u8 power_control; /* 0x12 (SDIO version 1.10) */ - - u8 speed_control; /* 0x13 */ -} sdio_regs_t; - -/* SDIO Device CCCR offsets */ -#define SDIOD_CCCR_REV 0x00 -#define SDIOD_CCCR_SDREV 0x01 -#define SDIOD_CCCR_IOEN 0x02 -#define SDIOD_CCCR_IORDY 0x03 -#define SDIOD_CCCR_INTEN 0x04 -#define SDIOD_CCCR_INTPEND 0x05 -#define SDIOD_CCCR_IOABORT 0x06 -#define SDIOD_CCCR_BICTRL 0x07 -#define SDIOD_CCCR_CAPABLITIES 0x08 -#define SDIOD_CCCR_CISPTR_0 0x09 -#define SDIOD_CCCR_CISPTR_1 0x0A -#define SDIOD_CCCR_CISPTR_2 0x0B -#define SDIOD_CCCR_BUSSUSP 0x0C -#define SDIOD_CCCR_FUNCSEL 0x0D -#define SDIOD_CCCR_EXECFLAGS 0x0E -#define SDIOD_CCCR_RDYFLAGS 0x0F -#define SDIOD_CCCR_BLKSIZE_0 0x10 -#define SDIOD_CCCR_BLKSIZE_1 0x11 -#define SDIOD_CCCR_POWER_CONTROL 0x12 -#define SDIOD_CCCR_SPEED_CONTROL 0x13 - -/* Broadcom extensions (corerev >= 1) */ -#define SDIOD_CCCR_BRCM_SEPINT 0xf2 - -/* cccr_sdio_rev */ -#define SDIO_REV_SDIOID_MASK 0xf0 /* SDIO spec revision number */ -#define SDIO_REV_CCCRID_MASK 0x0f /* CCCR format version number */ - -/* sd_rev */ -#define SD_REV_PHY_MASK 0x0f /* SD format version number */ - -/* io_en */ -#define SDIO_FUNC_ENABLE_1 0x02 /* function 1 I/O enable */ -#define SDIO_FUNC_ENABLE_2 0x04 /* function 2 I/O enable */ - -/* io_rdys */ -#define SDIO_FUNC_READY_1 0x02 /* function 1 I/O ready */ -#define SDIO_FUNC_READY_2 0x04 /* function 2 I/O ready */ - -/* intr_ctl */ -#define INTR_CTL_MASTER_EN 0x1 /* interrupt enable master */ -#define INTR_CTL_FUNC1_EN 0x2 /* interrupt enable for function 1 */ -#define INTR_CTL_FUNC2_EN 0x4 /* interrupt enable for function 2 */ - -/* intr_status */ -#define INTR_STATUS_FUNC1 0x2 /* interrupt pending for function 1 */ -#define INTR_STATUS_FUNC2 0x4 /* interrupt pending for function 2 */ - -/* io_abort */ -#define IO_ABORT_RESET_ALL 0x08 /* I/O card reset */ -#define IO_ABORT_FUNC_MASK 0x07 /* abort selction: function x */ - -/* bus_inter */ -#define BUS_CARD_DETECT_DIS 0x80 /* Card Detect disable */ -#define BUS_SPI_CONT_INTR_CAP 0x40 /* support continuous SPI interrupt */ -#define BUS_SPI_CONT_INTR_EN 0x20 /* continuous SPI interrupt enable */ -#define BUS_SD_DATA_WIDTH_MASK 0x03 /* bus width mask */ -#define BUS_SD_DATA_WIDTH_4BIT 0x02 /* bus width 4-bit mode */ -#define BUS_SD_DATA_WIDTH_1BIT 0x00 /* bus width 1-bit mode */ - -/* capability */ -#define SDIO_CAP_4BLS 0x80 /* 4-bit support for low speed card */ -#define SDIO_CAP_LSC 0x40 /* low speed card */ -#define SDIO_CAP_E4MI 0x20 /* enable interrupt between block of data in 4-bit mode */ -#define SDIO_CAP_S4MI 0x10 /* support interrupt between block of data in 4-bit mode */ -#define SDIO_CAP_SBS 0x08 /* support suspend/resume */ -#define SDIO_CAP_SRW 0x04 /* support read wait */ -#define SDIO_CAP_SMB 0x02 /* support multi-block transfer */ -#define SDIO_CAP_SDC 0x01 /* Support Direct commands during multi-byte transfer */ - -/* power_control */ -#define SDIO_POWER_SMPC 0x01 /* supports master power control (RO) */ -#define SDIO_POWER_EMPC 0x02 /* enable master power control (allow > 200mA) (RW) */ - -/* speed_control (control device entry into high-speed clocking mode) */ -#define SDIO_SPEED_SHS 0x01 /* supports high-speed [clocking] mode (RO) */ -#define SDIO_SPEED_EHS 0x02 /* enable high-speed [clocking] mode (RW) */ - -/* brcm sepint */ -#define SDIO_SEPINT_MASK 0x01 /* route sdpcmdev intr onto separate pad (chip-specific) */ -#define SDIO_SEPINT_OE 0x02 /* 1 asserts output enable for above pad */ -#define SDIO_SEPINT_ACT_HI 0x04 /* use active high interrupt level instead of active low */ - -/* FBR structure for function 1-7, FBR addresses and register offsets */ -typedef volatile struct { - u8 devctr; /* device interface, CSA control */ - u8 ext_dev; /* extended standard I/O device type code */ - u8 pwr_sel; /* power selection support */ - u8 PAD[6]; /* reserved */ - - u8 cis_low; /* CIS LSB */ - u8 cis_mid; - u8 cis_high; /* CIS MSB */ - u8 csa_low; /* code storage area, LSB */ - u8 csa_mid; - u8 csa_high; /* code storage area, MSB */ - u8 csa_dat_win; /* data access window to function */ - - u8 fnx_blk_size[2]; /* block size, little endian */ -} sdio_fbr_t; - -/* Maximum number of I/O funcs */ -#define SDIOD_MAX_IOFUNCS 7 - -/* SDIO Device FBR Start Address */ -#define SDIOD_FBR_STARTADDR 0x100 - -/* SDIO Device FBR Size */ -#define SDIOD_FBR_SIZE 0x100 - -/* Macro to calculate FBR register base */ -#define SDIOD_FBR_BASE(n) ((n) * 0x100) - -/* Function register offsets */ -#define SDIOD_FBR_DEVCTR 0x00 /* basic info for function */ -#define SDIOD_FBR_EXT_DEV 0x01 /* extended I/O device code */ -#define SDIOD_FBR_PWR_SEL 0x02 /* power selection bits */ - -/* SDIO Function CIS ptr offset */ -#define SDIOD_FBR_CISPTR_0 0x09 -#define SDIOD_FBR_CISPTR_1 0x0A -#define SDIOD_FBR_CISPTR_2 0x0B - -/* Code Storage Area pointer */ -#define SDIOD_FBR_CSA_ADDR_0 0x0C -#define SDIOD_FBR_CSA_ADDR_1 0x0D -#define SDIOD_FBR_CSA_ADDR_2 0x0E -#define SDIOD_FBR_CSA_DATA 0x0F - -/* SDIO Function I/O Block Size */ -#define SDIOD_FBR_BLKSIZE_0 0x10 -#define SDIOD_FBR_BLKSIZE_1 0x11 - -/* devctr */ -#define SDIOD_FBR_DEVCTR_DIC 0x0f /* device interface code */ -#define SDIOD_FBR_DECVTR_CSA 0x40 /* CSA support flag */ -#define SDIOD_FBR_DEVCTR_CSA_EN 0x80 /* CSA enabled */ -/* interface codes */ -#define SDIOD_DIC_NONE 0 /* SDIO standard interface is not supported */ -#define SDIOD_DIC_UART 1 -#define SDIOD_DIC_BLUETOOTH_A 2 -#define SDIOD_DIC_BLUETOOTH_B 3 -#define SDIOD_DIC_GPS 4 -#define SDIOD_DIC_CAMERA 5 -#define SDIOD_DIC_PHS 6 -#define SDIOD_DIC_WLAN 7 -#define SDIOD_DIC_EXT 0xf /* extended device interface, read ext_dev register */ - -/* pwr_sel */ -#define SDIOD_PWR_SEL_SPS 0x01 /* supports power selection */ -#define SDIOD_PWR_SEL_EPS 0x02 /* enable power selection (low-current mode) */ - -/* misc defines */ -#define SDIO_FUNC_0 0 -#define SDIO_FUNC_1 1 -#define SDIO_FUNC_2 2 -#define SDIO_FUNC_3 3 -#define SDIO_FUNC_4 4 -#define SDIO_FUNC_5 5 -#define SDIO_FUNC_6 6 -#define SDIO_FUNC_7 7 - -#define SD_CARD_TYPE_UNKNOWN 0 /* bad type or unrecognized */ -#define SD_CARD_TYPE_IO 1 /* IO only card */ -#define SD_CARD_TYPE_MEMORY 2 /* memory only card */ -#define SD_CARD_TYPE_COMBO 3 /* IO and memory combo card */ - -#define SDIO_MAX_BLOCK_SIZE 2048 /* maximum block size for block mode operation */ -#define SDIO_MIN_BLOCK_SIZE 1 /* minimum block size for block mode operation */ - -/* Card registers: status bit position */ -#define CARDREG_STATUS_BIT_OUTOFRANGE 31 -#define CARDREG_STATUS_BIT_COMCRCERROR 23 -#define CARDREG_STATUS_BIT_ILLEGALCOMMAND 22 -#define CARDREG_STATUS_BIT_ERROR 19 -#define CARDREG_STATUS_BIT_IOCURRENTSTATE3 12 -#define CARDREG_STATUS_BIT_IOCURRENTSTATE2 11 -#define CARDREG_STATUS_BIT_IOCURRENTSTATE1 10 -#define CARDREG_STATUS_BIT_IOCURRENTSTATE0 9 -#define CARDREG_STATUS_BIT_FUN_NUM_ERROR 4 - -#define SD_CMD_GO_IDLE_STATE 0 /* mandatory for SDIO */ -#define SD_CMD_SEND_OPCOND 1 -#define SD_CMD_MMC_SET_RCA 3 -#define SD_CMD_IO_SEND_OP_COND 5 /* mandatory for SDIO */ -#define SD_CMD_SELECT_DESELECT_CARD 7 -#define SD_CMD_SEND_CSD 9 -#define SD_CMD_SEND_CID 10 -#define SD_CMD_STOP_TRANSMISSION 12 -#define SD_CMD_SEND_STATUS 13 -#define SD_CMD_GO_INACTIVE_STATE 15 -#define SD_CMD_SET_BLOCKLEN 16 -#define SD_CMD_READ_SINGLE_BLOCK 17 -#define SD_CMD_READ_MULTIPLE_BLOCK 18 -#define SD_CMD_WRITE_BLOCK 24 -#define SD_CMD_WRITE_MULTIPLE_BLOCK 25 -#define SD_CMD_PROGRAM_CSD 27 -#define SD_CMD_SET_WRITE_PROT 28 -#define SD_CMD_CLR_WRITE_PROT 29 -#define SD_CMD_SEND_WRITE_PROT 30 -#define SD_CMD_ERASE_WR_BLK_START 32 -#define SD_CMD_ERASE_WR_BLK_END 33 -#define SD_CMD_ERASE 38 -#define SD_CMD_LOCK_UNLOCK 42 -#define SD_CMD_IO_RW_DIRECT 52 /* mandatory for SDIO */ -#define SD_CMD_IO_RW_EXTENDED 53 /* mandatory for SDIO */ -#define SD_CMD_APP_CMD 55 -#define SD_CMD_GEN_CMD 56 -#define SD_CMD_READ_OCR 58 -#define SD_CMD_CRC_ON_OFF 59 /* mandatory for SDIO */ -#define SD_ACMD_SD_STATUS 13 -#define SD_ACMD_SEND_NUM_WR_BLOCKS 22 -#define SD_ACMD_SET_WR_BLOCK_ERASE_CNT 23 -#define SD_ACMD_SD_SEND_OP_COND 41 -#define SD_ACMD_SET_CLR_CARD_DETECT 42 -#define SD_ACMD_SEND_SCR 51 - -/* argument for SD_CMD_IO_RW_DIRECT and SD_CMD_IO_RW_EXTENDED */ -#define SD_IO_OP_READ 0 /* Read_Write: Read */ -#define SD_IO_OP_WRITE 1 /* Read_Write: Write */ -#define SD_IO_RW_NORMAL 0 /* no RAW */ -#define SD_IO_RW_RAW 1 /* RAW */ -#define SD_IO_BYTE_MODE 0 /* Byte Mode */ -#define SD_IO_BLOCK_MODE 1 /* BlockMode */ -#define SD_IO_FIXED_ADDRESS 0 /* fix Address */ -#define SD_IO_INCREMENT_ADDRESS 1 /* IncrementAddress */ - -/* build SD_CMD_IO_RW_DIRECT Argument */ -#define SDIO_IO_RW_DIRECT_ARG(rw, raw, func, addr, data) \ - ((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((raw) & 1) << 27) | \ - (((addr) & 0x1FFFF) << 9) | ((data) & 0xFF)) - -/* build SD_CMD_IO_RW_EXTENDED Argument */ -#define SDIO_IO_RW_EXTENDED_ARG(rw, blk, func, addr, inc_addr, count) \ - ((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((blk) & 1) << 27) | \ - (((inc_addr) & 1) << 26) | (((addr) & 0x1FFFF) << 9) | ((count) & 0x1FF)) - -/* SDIO response parameters */ -#define SD_RSP_NO_NONE 0 -#define SD_RSP_NO_1 1 -#define SD_RSP_NO_2 2 -#define SD_RSP_NO_3 3 -#define SD_RSP_NO_4 4 -#define SD_RSP_NO_5 5 -#define SD_RSP_NO_6 6 - - /* Modified R6 response (to CMD3) */ -#define SD_RSP_MR6_COM_CRC_ERROR 0x8000 -#define SD_RSP_MR6_ILLEGAL_COMMAND 0x4000 -#define SD_RSP_MR6_ERROR 0x2000 - - /* Modified R1 in R4 Response (to CMD5) */ -#define SD_RSP_MR1_SBIT 0x80 -#define SD_RSP_MR1_PARAMETER_ERROR 0x40 -#define SD_RSP_MR1_RFU5 0x20 -#define SD_RSP_MR1_FUNC_NUM_ERROR 0x10 -#define SD_RSP_MR1_COM_CRC_ERROR 0x08 -#define SD_RSP_MR1_ILLEGAL_COMMAND 0x04 -#define SD_RSP_MR1_RFU1 0x02 -#define SD_RSP_MR1_IDLE_STATE 0x01 - - /* R5 response (to CMD52 and CMD53) */ -#define SD_RSP_R5_COM_CRC_ERROR 0x80 -#define SD_RSP_R5_ILLEGAL_COMMAND 0x40 -#define SD_RSP_R5_IO_CURRENTSTATE1 0x20 -#define SD_RSP_R5_IO_CURRENTSTATE0 0x10 -#define SD_RSP_R5_ERROR 0x08 -#define SD_RSP_R5_RFU 0x04 -#define SD_RSP_R5_FUNC_NUM_ERROR 0x02 -#define SD_RSP_R5_OUT_OF_RANGE 0x01 - -#define SD_RSP_R5_ERRBITS 0xCB - -/* ------------------------------------------------ - * SDIO Commands and responses - * - * I/O only commands are: - * CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53 - * ------------------------------------------------ - */ - -/* SDIO Commands */ -#define SDIOH_CMD_0 0 -#define SDIOH_CMD_3 3 -#define SDIOH_CMD_5 5 -#define SDIOH_CMD_7 7 -#define SDIOH_CMD_15 15 -#define SDIOH_CMD_52 52 -#define SDIOH_CMD_53 53 -#define SDIOH_CMD_59 59 - -/* SDIO Command Responses */ -#define SDIOH_RSP_NONE 0 -#define SDIOH_RSP_R1 1 -#define SDIOH_RSP_R2 2 -#define SDIOH_RSP_R3 3 -#define SDIOH_RSP_R4 4 -#define SDIOH_RSP_R5 5 -#define SDIOH_RSP_R6 6 - -/* - * SDIO Response Error flags - */ -#define SDIOH_RSP5_ERROR_FLAGS 0xCB - -/* ------------------------------------------------ - * SDIO Command structures. I/O only commands are: - * - * CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53 - * ------------------------------------------------ - */ - -#define CMD5_OCR_M BITFIELD_MASK(24) -#define CMD5_OCR_S 0 - -#define CMD7_RCA_M BITFIELD_MASK(16) -#define CMD7_RCA_S 16 - -#define CMD_15_RCA_M BITFIELD_MASK(16) -#define CMD_15_RCA_S 16 - -#define CMD52_DATA_M BITFIELD_MASK(8) /* Bits [7:0] - Write Data/Stuff bits of CMD52 - */ -#define CMD52_DATA_S 0 -#define CMD52_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */ -#define CMD52_REG_ADDR_S 9 -#define CMD52_RAW_M BITFIELD_MASK(1) /* Bit 27 - Read after Write flag */ -#define CMD52_RAW_S 27 -#define CMD52_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */ -#define CMD52_FUNCTION_S 28 -#define CMD52_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */ -#define CMD52_RW_FLAG_S 31 - -#define CMD53_BYTE_BLK_CNT_M BITFIELD_MASK(9) /* Bits [8:0] - Byte/Block Count of CMD53 */ -#define CMD53_BYTE_BLK_CNT_S 0 -#define CMD53_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */ -#define CMD53_REG_ADDR_S 9 -#define CMD53_OP_CODE_M BITFIELD_MASK(1) /* Bit 26 - R/W Operation Code */ -#define CMD53_OP_CODE_S 26 -#define CMD53_BLK_MODE_M BITFIELD_MASK(1) /* Bit 27 - Block Mode */ -#define CMD53_BLK_MODE_S 27 -#define CMD53_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */ -#define CMD53_FUNCTION_S 28 -#define CMD53_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */ -#define CMD53_RW_FLAG_S 31 - -/* ------------------------------------------------------ - * SDIO Command Response structures for SD1 and SD4 modes - * ----------------------------------------------------- - */ -#define RSP4_IO_OCR_M BITFIELD_MASK(24) /* Bits [23:0] - Card's OCR Bits [23:0] */ -#define RSP4_IO_OCR_S 0 -#define RSP4_STUFF_M BITFIELD_MASK(3) /* Bits [26:24] - Stuff bits */ -#define RSP4_STUFF_S 24 -#define RSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 27 - Memory present */ -#define RSP4_MEM_PRESENT_S 27 -#define RSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [30:28] - Number of I/O funcs */ -#define RSP4_NUM_FUNCS_S 28 -#define RSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 31 - SDIO card ready */ -#define RSP4_CARD_READY_S 31 - -#define RSP6_STATUS_M BITFIELD_MASK(16) /* Bits [15:0] - Card status bits [19,22,23,12:0] - */ -#define RSP6_STATUS_S 0 -#define RSP6_IO_RCA_M BITFIELD_MASK(16) /* Bits [31:16] - RCA bits[31-16] */ -#define RSP6_IO_RCA_S 16 - -#define RSP1_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error */ -#define RSP1_AKE_SEQ_ERROR_S 3 -#define RSP1_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */ -#define RSP1_APP_CMD_S 5 -#define RSP1_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data (buff empty) */ -#define RSP1_READY_FOR_DATA_S 8 -#define RSP1_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - State of card - * when Cmd was received - */ -#define RSP1_CURR_STATE_S 9 -#define RSP1_EARSE_RESET_M BITFIELD_MASK(1) /* Bit 13 - Erase seq cleared */ -#define RSP1_EARSE_RESET_S 13 -#define RSP1_CARD_ECC_DISABLE_M BITFIELD_MASK(1) /* Bit 14 - Card ECC disabled */ -#define RSP1_CARD_ECC_DISABLE_S 14 -#define RSP1_WP_ERASE_SKIP_M BITFIELD_MASK(1) /* Bit 15 - Partial blocks erased due to W/P */ -#define RSP1_WP_ERASE_SKIP_S 15 -#define RSP1_CID_CSD_OVERW_M BITFIELD_MASK(1) /* Bit 16 - Illegal write to CID or R/O bits - * of CSD - */ -#define RSP1_CID_CSD_OVERW_S 16 -#define RSP1_ERROR_M BITFIELD_MASK(1) /* Bit 19 - General/Unknown error */ -#define RSP1_ERROR_S 19 -#define RSP1_CC_ERROR_M BITFIELD_MASK(1) /* Bit 20 - Internal Card Control error */ -#define RSP1_CC_ERROR_S 20 -#define RSP1_CARD_ECC_FAILED_M BITFIELD_MASK(1) /* Bit 21 - Card internal ECC failed - * to correct data - */ -#define RSP1_CARD_ECC_FAILED_S 21 -#define RSP1_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 22 - Cmd not legal for the card state */ -#define RSP1_ILLEGAL_CMD_S 22 -#define RSP1_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 23 - CRC check of previous command failed - */ -#define RSP1_COM_CRC_ERROR_S 23 -#define RSP1_LOCK_UNLOCK_FAIL_M BITFIELD_MASK(1) /* Bit 24 - Card lock-unlock Cmd Seq error */ -#define RSP1_LOCK_UNLOCK_FAIL_S 24 -#define RSP1_CARD_LOCKED_M BITFIELD_MASK(1) /* Bit 25 - Card locked by the host */ -#define RSP1_CARD_LOCKED_S 25 -#define RSP1_WP_VIOLATION_M BITFIELD_MASK(1) /* Bit 26 - Attempt to program - * write-protected blocks - */ -#define RSP1_WP_VIOLATION_S 26 -#define RSP1_ERASE_PARAM_M BITFIELD_MASK(1) /* Bit 27 - Invalid erase blocks */ -#define RSP1_ERASE_PARAM_S 27 -#define RSP1_ERASE_SEQ_ERR_M BITFIELD_MASK(1) /* Bit 28 - Erase Cmd seq error */ -#define RSP1_ERASE_SEQ_ERR_S 28 -#define RSP1_BLK_LEN_ERR_M BITFIELD_MASK(1) /* Bit 29 - Block length error */ -#define RSP1_BLK_LEN_ERR_S 29 -#define RSP1_ADDR_ERR_M BITFIELD_MASK(1) /* Bit 30 - Misaligned address */ -#define RSP1_ADDR_ERR_S 30 -#define RSP1_OUT_OF_RANGE_M BITFIELD_MASK(1) /* Bit 31 - Cmd arg was out of range */ -#define RSP1_OUT_OF_RANGE_S 31 - -#define RSP5_DATA_M BITFIELD_MASK(8) /* Bits [0:7] - data */ -#define RSP5_DATA_S 0 -#define RSP5_FLAGS_M BITFIELD_MASK(8) /* Bit [15:8] - Rsp flags */ -#define RSP5_FLAGS_S 8 -#define RSP5_STUFF_M BITFIELD_MASK(16) /* Bits [31:16] - Stuff bits */ -#define RSP5_STUFF_S 16 - -/* ---------------------------------------------- - * SDIO Command Response structures for SPI mode - * ---------------------------------------------- - */ -#define SPIRSP4_IO_OCR_M BITFIELD_MASK(16) /* Bits [15:0] - Card's OCR Bits [23:8] */ -#define SPIRSP4_IO_OCR_S 0 -#define SPIRSP4_STUFF_M BITFIELD_MASK(3) /* Bits [18:16] - Stuff bits */ -#define SPIRSP4_STUFF_S 16 -#define SPIRSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 19 - Memory present */ -#define SPIRSP4_MEM_PRESENT_S 19 -#define SPIRSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [22:20] - Number of I/O funcs */ -#define SPIRSP4_NUM_FUNCS_S 20 -#define SPIRSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 23 - SDIO card ready */ -#define SPIRSP4_CARD_READY_S 23 -#define SPIRSP4_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - idle state */ -#define SPIRSP4_IDLE_STATE_S 24 -#define SPIRSP4_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */ -#define SPIRSP4_ILLEGAL_CMD_S 26 -#define SPIRSP4_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */ -#define SPIRSP4_COM_CRC_ERROR_S 27 -#define SPIRSP4_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error - */ -#define SPIRSP4_FUNC_NUM_ERROR_S 28 -#define SPIRSP4_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */ -#define SPIRSP4_PARAM_ERROR_S 30 -#define SPIRSP4_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */ -#define SPIRSP4_START_BIT_S 31 - -#define SPIRSP5_DATA_M BITFIELD_MASK(8) /* Bits [23:16] - R/W Data */ -#define SPIRSP5_DATA_S 16 -#define SPIRSP5_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - Idle state */ -#define SPIRSP5_IDLE_STATE_S 24 -#define SPIRSP5_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */ -#define SPIRSP5_ILLEGAL_CMD_S 26 -#define SPIRSP5_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */ -#define SPIRSP5_COM_CRC_ERROR_S 27 -#define SPIRSP5_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error - */ -#define SPIRSP5_FUNC_NUM_ERROR_S 28 -#define SPIRSP5_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */ -#define SPIRSP5_PARAM_ERROR_S 30 -#define SPIRSP5_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */ -#define SPIRSP5_START_BIT_S 31 - -/* RSP6 card status format; Pg 68 Physical Layer spec v 1.10 */ -#define RSP6STAT_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error - */ -#define RSP6STAT_AKE_SEQ_ERROR_S 3 -#define RSP6STAT_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */ -#define RSP6STAT_APP_CMD_S 5 -#define RSP6STAT_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data - * (buff empty) - */ -#define RSP6STAT_READY_FOR_DATA_S 8 -#define RSP6STAT_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - Card state at - * Cmd reception - */ -#define RSP6STAT_CURR_STATE_S 9 -#define RSP6STAT_ERROR_M BITFIELD_MASK(1) /* Bit 13 - General/Unknown error Bit 19 - */ -#define RSP6STAT_ERROR_S 13 -#define RSP6STAT_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 14 - Illegal cmd for - * card state Bit 22 - */ -#define RSP6STAT_ILLEGAL_CMD_S 14 -#define RSP6STAT_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 15 - CRC previous command - * failed Bit 23 - */ -#define RSP6STAT_COM_CRC_ERROR_S 15 - -#define SDIOH_XFER_TYPE_READ SD_IO_OP_READ -#define SDIOH_XFER_TYPE_WRITE SD_IO_OP_WRITE - -#endif /* def BCMSDIO */ -#endif /* _SDIO_H */