From: Mike Rapoport Date: Wed, 10 Feb 2016 16:34:06 +0000 (+0200) Subject: staging: sm750fb: refactor setDisplayControl function X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=b117b637da2be83c8173b53986b51ad5b8169d8d;p=GitHub%2FLineageOS%2Fandroid_kernel_motorola_exynos9610.git staging: sm750fb: refactor setDisplayControl function The enable/disbable sequence in setDisplayControl function is duplicated for primary and secondary display controllers. The function can be refactored so that the common part of register access will be shared for both controllers. Signed-off-by: Mike Rapoport Signed-off-by: Greg Kroah-Hartman --- diff --git a/drivers/staging/sm750fb/ddk750_display.c b/drivers/staging/sm750fb/ddk750_display.c index f3f0026ac010..ae8bb371d2b2 100644 --- a/drivers/staging/sm750fb/ddk750_display.c +++ b/drivers/staging/sm750fb/ddk750_display.c @@ -9,96 +9,55 @@ static void setDisplayControl(int ctrl, int disp_state) { /* state != 0 means turn on both timing & plane en_bit */ - unsigned long reg, reserved; - int cnt; + unsigned long reg, val, reserved; + int cnt = 0; - cnt = 0; - - /* Set the primary display control */ if (!ctrl) { - reg = PEEK32(PANEL_DISPLAY_CTRL); - /* Turn on/off the Panel display control */ - if (disp_state) { - /* Timing should be enabled first before enabling the plane - * because changing at the same time does not guarantee that - * the plane will also enabled or disabled. - */ - reg = FIELD_SET(reg, DISPLAY_CTRL, TIMING, ENABLE); - POKE32(PANEL_DISPLAY_CTRL, reg); - - reg = FIELD_SET(reg, DISPLAY_CTRL, PLANE, ENABLE); - - /* Added some masks to mask out the reserved bits. - * Sometimes, the reserved bits are set/reset randomly when - * writing to the PRIMARY_DISPLAY_CTRL, therefore, the register - * reserved bits are needed to be masked out. - */ - reserved = PANEL_DISPLAY_CTRL_RESERVED_MASK; - - /* Somehow the register value on the plane is not set - * until a few delay. Need to write - * and read it a couple times - */ - do { - cnt++; - POKE32(PANEL_DISPLAY_CTRL, reg); - } while ((PEEK32(PANEL_DISPLAY_CTRL) & ~reserved) != - (reg & ~reserved)); - printk("Set Panel Plane enbit:after tried %d times\n", cnt); - } else { - /* When turning off, there is no rule on the programming - * sequence since whenever the clock is off, then it does not - * matter whether the plane is enabled or disabled. - * Note: Modifying the plane bit will take effect on the - * next vertical sync. Need to find out if it is necessary to - * wait for 1 vsync before modifying the timing enable bit. - * */ - reg = FIELD_SET(reg, DISPLAY_CTRL, PLANE, DISABLE); - POKE32(PANEL_DISPLAY_CTRL, reg); - - reg = FIELD_SET(reg, DISPLAY_CTRL, TIMING, DISABLE); - POKE32(PANEL_DISPLAY_CTRL, reg); - } - + reg = PANEL_DISPLAY_CTRL; + reserved = PANEL_DISPLAY_CTRL_RESERVED_MASK; } else { - /* Set the secondary display control */ - reg = PEEK32(CRT_DISPLAY_CTRL); + reg = CRT_DISPLAY_CTRL; + reserved = CRT_DISPLAY_CTRL_RESERVED_MASK; + } - if (disp_state) { - /* Timing should be enabled first before enabling the plane because changing at the - same time does not guarantee that the plane will also enabled or disabled. - */ - reg = FIELD_SET(reg, DISPLAY_CTRL, TIMING, ENABLE); - POKE32(CRT_DISPLAY_CTRL, reg); - - reg = FIELD_SET(reg, DISPLAY_CTRL, PLANE, ENABLE); - - /* Added some masks to mask out the reserved bits. - * Sometimes, the reserved bits are set/reset randomly when - * writing to the PRIMARY_DISPLAY_CTRL, therefore, the register - * reserved bits are needed to be masked out. - */ - reserved = CRT_DISPLAY_CTRL_RESERVED_MASK; - do { - cnt++; - POKE32(CRT_DISPLAY_CTRL, reg); - } while ((PEEK32(CRT_DISPLAY_CTRL) & ~reserved) != - (reg & ~reserved)); - printk("Set Crt Plane enbit:after tried %d times\n", cnt); - } else { - /* When turning off, there is no rule on the programming - * sequence since whenever the clock is off, then it does not - * matter whether the plane is enabled or disabled. - * Note: Modifying the plane bit will take effect on the next - * vertical sync. Need to find out if it is necessary to - * wait for 1 vsync before modifying the timing enable bit. - */ - reg = FIELD_SET(reg, DISPLAY_CTRL, PLANE, DISABLE); - POKE32(CRT_DISPLAY_CTRL, reg); - - reg = FIELD_SET(reg, DISPLAY_CTRL, TIMING, DISABLE); - POKE32(CRT_DISPLAY_CTRL, reg); - } + val = PEEK32(reg); + if (disp_state) { + /* + * Timing should be enabled first before enabling the + * plane because changing at the same time does not + * guarantee that the plane will also enabled or + * disabled. + */ + val = FIELD_SET(val, DISPLAY_CTRL, TIMING, ENABLE); + POKE32(reg, val); + + val = FIELD_SET(val, DISPLAY_CTRL, PLANE, ENABLE); + + /* + * Somehow the register value on the plane is not set + * until a few delay. Need to write and read it a + * couple times + */ + do { + cnt++; + POKE32(reg, val); + } while ((PEEK32(reg) & ~reserved) != (val & ~reserved)); + pr_debug("Set Plane enbit:after tried %d times\n", cnt); + } else { + /* + * When turning off, there is no rule on the + * programming sequence since whenever the clock is + * off, then it does not matter whether the plane is + * enabled or disabled. Note: Modifying the plane bit + * will take effect on the next vertical sync. Need to + * find out if it is necessary to wait for 1 vsync + * before modifying the timing enable bit. + */ + val = FIELD_SET(val, DISPLAY_CTRL, PLANE, DISABLE); + POKE32(reg, val); + + val = FIELD_SET(val, DISPLAY_CTRL, TIMING, DISABLE); + POKE32(reg, val); } }