From: Stephen Hemminger Date: Thu, 15 May 2008 00:04:17 +0000 (-0700) Subject: sky2: pci power savings X-Git-Tag: MMI-PSA29.97-13-9~33552^2~371 X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=a068c0adf2fe28b324bca87f85d27af7f993cdaf;p=GitHub%2FMotorolaMobilityLLC%2Fkernel-slsi.git sky2: pci power savings Turn on special bits to save more power when device is shutdown. Tested on a limited range of hardware, some of the bits are for hardware that probably isn't even in production (like Yukon Supreme) and was ported from the vendor driver. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 59cb9cd00ad2..c83406f4f2a7 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -284,6 +284,86 @@ static void sky2_power_aux(struct sky2_hw *hw) PC_VAUX_ON | PC_VCC_OFF)); } +static void sky2_power_state(struct sky2_hw *hw, pci_power_t state) +{ + u16 power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL); + int pex = pci_find_capability(hw->pdev, PCI_CAP_ID_EXP); + u32 reg; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + + switch (state) { + case PCI_D0: + break; + + case PCI_D1: + power_control |= 1; + break; + + case PCI_D2: + power_control |= 2; + break; + + case PCI_D3hot: + case PCI_D3cold: + power_control |= 3; + if (hw->flags & SKY2_HW_ADV_POWER_CTL) { + /* additional power saving measurements */ + reg = sky2_pci_read32(hw, PCI_DEV_REG4); + + /* set gating core clock for LTSSM in L1 state */ + reg |= P_PEX_LTSSM_STAT(P_PEX_LTSSM_L1_STAT) | + /* auto clock gated scheme controlled by CLKREQ */ + P_ASPM_A1_MODE_SELECT | + /* enable Gate Root Core Clock */ + P_CLK_GATE_ROOT_COR_ENA; + + if (pex && (hw->flags & SKY2_HW_CLK_POWER)) { + /* enable Clock Power Management (CLKREQ) */ + u16 ctrl = sky2_pci_read16(hw, pex + PCI_EXP_DEVCTL); + + ctrl |= PCI_EXP_DEVCTL_AUX_PME; + sky2_pci_write16(hw, pex + PCI_EXP_DEVCTL, ctrl); + } else + /* force CLKREQ Enable in Our4 (A1b only) */ + reg |= P_ASPM_FORCE_CLKREQ_ENA; + + /* set Mask Register for Release/Gate Clock */ + sky2_pci_write32(hw, PCI_DEV_REG5, + P_REL_PCIE_EXIT_L1_ST | P_GAT_PCIE_ENTER_L1_ST | + P_REL_PCIE_RX_EX_IDLE | P_GAT_PCIE_RX_EL_IDLE | + P_REL_GPHY_LINK_UP | P_GAT_GPHY_LINK_DOWN); + } else + sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_CLK_HALT); + + /* put CPU into reset state */ + sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_RESET); + if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev == CHIP_REV_YU_SU_A0) + /* put CPU into halt state */ + sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_HALTED); + + if (pex && !(hw->flags & SKY2_HW_RAM_BUFFER)) { + reg = sky2_pci_read32(hw, PCI_DEV_REG1); + /* force to PCIe L1 */ + reg |= PCI_FORCE_PEX_L1; + sky2_pci_write32(hw, PCI_DEV_REG1, reg); + } + break; + + default: + dev_warn(&hw->pdev->dev, PFX "Invalid power state (%d) ", + state); + return; + } + + power_control |= PCI_PM_CTRL_PME_ENABLE; + /* Finally, set the new power state. */ + sky2_pci_write32(hw, hw->pm_cap + PCI_PM_CTRL, power_control); + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + sky2_pci_read32(hw, B0_CTST); +} + static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port) { u16 reg; @@ -2786,6 +2866,10 @@ static int __devinit sky2_init(struct sky2_hw *hw) hw->flags = SKY2_HW_GIGABIT | SKY2_HW_NEWER_PHY | SKY2_HW_ADV_POWER_CTL; + + /* check for Rev. A1 dev 4200 */ + if (sky2_read16(hw, Q_ADDR(Q_XA1, Q_WM)) == 0) + hw->flags |= SKY2_HW_CLK_POWER; break; case CHIP_ID_YUKON_EX: @@ -2836,6 +2920,11 @@ static int __devinit sky2_init(struct sky2_hw *hw) if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P') hw->flags |= SKY2_HW_FIBRE_PHY; + hw->pm_cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PM); + if (hw->pm_cap == 0) { + dev_err(&hw->pdev->dev, "cannot find PowerManagement capability\n"); + return -EIO; + } hw->ports = 1; t8 = sky2_read8(hw, B2_Y2_HW_RES); @@ -4407,7 +4496,7 @@ static int sky2_suspend(struct pci_dev *pdev, pm_message_t state) pci_save_state(pdev); pci_enable_wake(pdev, pci_choose_state(pdev, state), wol); - pci_set_power_state(pdev, pci_choose_state(pdev, state)); + sky2_power_state(hw, pci_choose_state(pdev, state)); return 0; } @@ -4420,9 +4509,7 @@ static int sky2_resume(struct pci_dev *pdev) if (!hw) return 0; - err = pci_set_power_state(pdev, PCI_D0); - if (err) - goto out; + sky2_power_state(hw, PCI_D0); err = pci_restore_state(pdev); if (err) @@ -4490,8 +4577,7 @@ static void sky2_shutdown(struct pci_dev *pdev) pci_enable_wake(pdev, PCI_D3cold, wol); pci_disable_device(pdev); - pci_set_power_state(pdev, PCI_D3hot); - + sky2_power_state(hw, PCI_D3hot); } static struct pci_driver sky2_driver = { diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index d63106cd74ba..1fa82bf029d9 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -28,6 +28,11 @@ enum pci_dev_reg_1 { PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */ PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */ + + PCI_PHY_LNK_TIM_MSK= 3L<<8,/* Bit 9.. 8: GPHY Link Trigger Timer */ + PCI_ENA_L1_EVENT = 1<<7, /* Enable PEX L1 Event */ + PCI_ENA_GPHY_LNK = 1<<6, /* Enable PEX L1 on GPHY Link down */ + PCI_FORCE_PEX_L1 = 1<<5, /* Force to PEX L1 */ }; enum pci_dev_reg_2 { @@ -45,7 +50,11 @@ enum pci_dev_reg_2 { /* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */ enum pci_dev_reg_4 { - /* (Link Training & Status State Machine) */ + /* (Link Training & Status State Machine) */ + P_PEX_LTSSM_STAT_MSK = 0x7fL<<25, /* Bit 31..25: PEX LTSSM Mask */ +#define P_PEX_LTSSM_STAT(x) ((x << 25) & P_PEX_LTSSM_STAT_MSK) + P_PEX_LTSSM_L1_STAT = 0x34, + P_PEX_LTSSM_DET_STAT = 0x01, P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */ /* (Active State Power Management) */ P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */ @@ -454,6 +463,9 @@ enum yukon_ex_rev { CHIP_REV_YU_EX_A0 = 1, CHIP_REV_YU_EX_B0 = 2, }; +enum yukon_supr_rev { + CHIP_REV_YU_SU_A0 = 0, +}; /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ @@ -2059,7 +2071,9 @@ struct sky2_hw { #define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */ #define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */ #define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */ +#define SKY2_HW_CLK_POWER 0x00000100 /* clock power management */ + int pm_cap; u8 chip_id; u8 chip_rev; u8 pmd_type;