From: Linus Walleij Date: Sat, 21 May 2016 18:43:16 +0000 (+0200) Subject: iio: st_sensors: switch to a threaded interrupt X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=65925b65ed98ffdb277cf5ea1af45731dac0b30b;p=GitHub%2Fmoto-9609%2Fandroid_kernel_motorola_exynos9610.git iio: st_sensors: switch to a threaded interrupt commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded ("iio: st_sensors: verify interrupt event to status") caused a regression when reading ST sensors from a HRTimer trigger rather than the intrinsic interrupts: the HRTimer may trigger faster than the sensor provides new values, and as the check against new values available as a cause of the interrupt trigger was done in the poll function, this would bail out of the HRTimer interrupt with IRQ_NONE. So clearly we need to only check the new values available from the proper interrupt handler and not from the poll function, which should rather just read the raw values from the registers, put them into the buffer and be happy. To achieve this: switch the ST Sensors over to using a true threaded interrupt handler. In the interrupt thread, check if new values are available, else yield to the (potential) next device on the same interrupt line to check the registers. If the interrupt was ours, proceed to poll the values. Instead of relying on iio_trigger_generic_data_rdy_poll() as a top half to wake up the thread that polls the sensor for new data, have the thread call iio_trigger_poll_chained() after determining that is is the proper source of the interrupt. This is modelled on drivers/iio/accel/mma8452.c which is already using a properly threaded interrupt handler. In order to get the same precision in timestamps as previously, where samples would be timestamped in the poll function pf->timestamp when calling iio_trigger_generic_data_rdy_poll() we introduce a local timestamp in the sensor data, set it in the top half (fastpath) of the interrupt handler and provide that to the core when calling iio_push_to_buffers_with_timestamp(). Additionally: if the active scanmask is not set for the sensor no IRQs should be enabled and we need to bail out with IRQ_NONE. This can happen if spurious IRQs fire when installing the threaded interrupt handler. Tested with hard interrupt triggers on LIS331DL, then also tested with hrtimers on the same sensor by creating a 75Hz HRTimer and using it to poll the sensor. Signed-off-by: Linus Walleij Cc: Giuseppe Barba Cc: Denis Ciocca Reported-by: Crestez Dan Leonard Tested-by: Crestez Dan Leonard Tested-by: Jonathan Cameron Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status") Signed-off-by: Jonathan Cameron --- diff --git a/drivers/iio/accel/st_accel_buffer.c b/drivers/iio/accel/st_accel_buffer.c index a1e642ee13d6..7fddc137e91e 100644 --- a/drivers/iio/accel/st_accel_buffer.c +++ b/drivers/iio/accel/st_accel_buffer.c @@ -91,7 +91,7 @@ static const struct iio_buffer_setup_ops st_accel_buffer_setup_ops = { int st_accel_allocate_ring(struct iio_dev *indio_dev) { - return iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, + return iio_triggered_buffer_setup(indio_dev, NULL, &st_sensors_trigger_handler, &st_accel_buffer_setup_ops); } diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c index dc73f2d85e6d..4d95bfc4786c 100644 --- a/drivers/iio/accel/st_accel_core.c +++ b/drivers/iio/accel/st_accel_core.c @@ -741,6 +741,7 @@ static const struct iio_info accel_info = { static const struct iio_trigger_ops st_accel_trigger_ops = { .owner = THIS_MODULE, .set_trigger_state = ST_ACCEL_TRIGGER_SET_STATE, + .validate_device = st_sensors_validate_device, }; #define ST_ACCEL_TRIGGER_OPS (&st_accel_trigger_ops) #else diff --git a/drivers/iio/common/st_sensors/st_sensors_buffer.c b/drivers/iio/common/st_sensors/st_sensors_buffer.c index c55898543a47..f1693dbebb8a 100644 --- a/drivers/iio/common/st_sensors/st_sensors_buffer.c +++ b/drivers/iio/common/st_sensors/st_sensors_buffer.c @@ -57,31 +57,20 @@ irqreturn_t st_sensors_trigger_handler(int irq, void *p) struct iio_poll_func *pf = p; struct iio_dev *indio_dev = pf->indio_dev; struct st_sensor_data *sdata = iio_priv(indio_dev); + s64 timestamp; - /* If we have a status register, check if this IRQ came from us */ - if (sdata->sensor_settings->drdy_irq.addr_stat_drdy) { - u8 status; - - len = sdata->tf->read_byte(&sdata->tb, sdata->dev, - sdata->sensor_settings->drdy_irq.addr_stat_drdy, - &status); - if (len < 0) - dev_err(sdata->dev, "could not read channel status\n"); - - /* - * If this was not caused by any channels on this sensor, - * return IRQ_NONE - */ - if (!(status & (u8)indio_dev->active_scan_mask[0])) - return IRQ_NONE; - } + /* If we do timetamping here, do it before reading the values */ + if (sdata->hw_irq_trigger) + timestamp = sdata->hw_timestamp; + else + timestamp = iio_get_time_ns(); len = st_sensors_get_buffer_element(indio_dev, sdata->buffer_data); if (len < 0) goto st_sensors_get_buffer_element_error; iio_push_to_buffers_with_timestamp(indio_dev, sdata->buffer_data, - pf->timestamp); + timestamp); st_sensors_get_buffer_element_error: iio_trigger_notify_done(indio_dev->trig); diff --git a/drivers/iio/common/st_sensors/st_sensors_core.c b/drivers/iio/common/st_sensors/st_sensors_core.c index dffe00692169..928ee68fcc5f 100644 --- a/drivers/iio/common/st_sensors/st_sensors_core.c +++ b/drivers/iio/common/st_sensors/st_sensors_core.c @@ -424,6 +424,9 @@ int st_sensors_set_dataready_irq(struct iio_dev *indio_dev, bool enable) else drdy_mask = sdata->sensor_settings->drdy_irq.mask_int2; + /* Flag to the poll function that the hardware trigger is in use */ + sdata->hw_irq_trigger = enable; + /* Enable/Disable the interrupt generator for data ready. */ err = st_sensors_write_data_with_mask(indio_dev, sdata->sensor_settings->drdy_irq.addr, diff --git a/drivers/iio/common/st_sensors/st_sensors_trigger.c b/drivers/iio/common/st_sensors/st_sensors_trigger.c index da72279fcf99..1f59bcc0f143 100644 --- a/drivers/iio/common/st_sensors/st_sensors_trigger.c +++ b/drivers/iio/common/st_sensors/st_sensors_trigger.c @@ -17,6 +17,73 @@ #include #include "st_sensors_core.h" +/** + * st_sensors_irq_handler() - top half of the IRQ-based triggers + * @irq: irq number + * @p: private handler data + */ +irqreturn_t st_sensors_irq_handler(int irq, void *p) +{ + struct iio_trigger *trig = p; + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct st_sensor_data *sdata = iio_priv(indio_dev); + + /* Get the time stamp as close in time as possible */ + sdata->hw_timestamp = iio_get_time_ns(); + return IRQ_WAKE_THREAD; +} + +/** + * st_sensors_irq_thread() - bottom half of the IRQ-based triggers + * @irq: irq number + * @p: private handler data + */ +irqreturn_t st_sensors_irq_thread(int irq, void *p) +{ + struct iio_trigger *trig = p; + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct st_sensor_data *sdata = iio_priv(indio_dev); + int ret; + + /* + * If this trigger is backed by a hardware interrupt and we have a + * status register, check if this IRQ came from us + */ + if (sdata->sensor_settings->drdy_irq.addr_stat_drdy) { + u8 status; + + ret = sdata->tf->read_byte(&sdata->tb, sdata->dev, + sdata->sensor_settings->drdy_irq.addr_stat_drdy, + &status); + if (ret < 0) { + dev_err(sdata->dev, "could not read channel status\n"); + goto out_poll; + } + /* + * the lower bits of .active_scan_mask[0] is directly mapped + * to the channels on the sensor: either bit 0 for + * one-dimensional sensors, or e.g. x,y,z for accelerometers, + * gyroscopes or magnetometers. No sensor use more than 3 + * channels, so cut the other status bits here. + */ + status &= 0x07; + + /* + * If this was not caused by any channels on this sensor, + * return IRQ_NONE + */ + if (!indio_dev->active_scan_mask) + return IRQ_NONE; + if (!(status & (u8)indio_dev->active_scan_mask[0])) + return IRQ_NONE; + } + +out_poll: + /* It's our IRQ: proceed to handle the register polling */ + iio_trigger_poll_chained(p); + return IRQ_HANDLED; +} + int st_sensors_allocate_trigger(struct iio_dev *indio_dev, const struct iio_trigger_ops *trigger_ops) { @@ -77,9 +144,12 @@ int st_sensors_allocate_trigger(struct iio_dev *indio_dev, sdata->sensor_settings->drdy_irq.addr_stat_drdy) irq_trig |= IRQF_SHARED; - err = request_threaded_irq(irq, - iio_trigger_generic_data_rdy_poll, - NULL, + /* Let's create an interrupt thread masking the hard IRQ here */ + irq_trig |= IRQF_ONESHOT; + + err = request_threaded_irq(sdata->get_irq_data_ready(indio_dev), + st_sensors_irq_handler, + st_sensors_irq_thread, irq_trig, sdata->trig->name, sdata->trig); @@ -119,6 +189,18 @@ void st_sensors_deallocate_trigger(struct iio_dev *indio_dev) } EXPORT_SYMBOL(st_sensors_deallocate_trigger); +int st_sensors_validate_device(struct iio_trigger *trig, + struct iio_dev *indio_dev) +{ + struct iio_dev *indio = iio_trigger_get_drvdata(trig); + + if (indio != indio_dev) + return -EINVAL; + + return 0; +} +EXPORT_SYMBOL(st_sensors_validate_device); + MODULE_AUTHOR("Denis Ciocca "); MODULE_DESCRIPTION("STMicroelectronics ST-sensors trigger"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/gyro/st_gyro_buffer.c b/drivers/iio/gyro/st_gyro_buffer.c index d67b17b6a7aa..a5377044e42f 100644 --- a/drivers/iio/gyro/st_gyro_buffer.c +++ b/drivers/iio/gyro/st_gyro_buffer.c @@ -91,7 +91,7 @@ static const struct iio_buffer_setup_ops st_gyro_buffer_setup_ops = { int st_gyro_allocate_ring(struct iio_dev *indio_dev) { - return iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, + return iio_triggered_buffer_setup(indio_dev, NULL, &st_sensors_trigger_handler, &st_gyro_buffer_setup_ops); } diff --git a/drivers/iio/gyro/st_gyro_core.c b/drivers/iio/gyro/st_gyro_core.c index 52a3c87c375c..a8012955a1f6 100644 --- a/drivers/iio/gyro/st_gyro_core.c +++ b/drivers/iio/gyro/st_gyro_core.c @@ -409,6 +409,7 @@ static const struct iio_info gyro_info = { static const struct iio_trigger_ops st_gyro_trigger_ops = { .owner = THIS_MODULE, .set_trigger_state = ST_GYRO_TRIGGER_SET_STATE, + .validate_device = st_sensors_validate_device, }; #define ST_GYRO_TRIGGER_OPS (&st_gyro_trigger_ops) #else diff --git a/drivers/iio/magnetometer/st_magn_buffer.c b/drivers/iio/magnetometer/st_magn_buffer.c index ecd3bd0a9769..0a9e8fadfa9d 100644 --- a/drivers/iio/magnetometer/st_magn_buffer.c +++ b/drivers/iio/magnetometer/st_magn_buffer.c @@ -82,7 +82,7 @@ static const struct iio_buffer_setup_ops st_magn_buffer_setup_ops = { int st_magn_allocate_ring(struct iio_dev *indio_dev) { - return iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, + return iio_triggered_buffer_setup(indio_dev, NULL, &st_sensors_trigger_handler, &st_magn_buffer_setup_ops); } diff --git a/drivers/iio/magnetometer/st_magn_core.c b/drivers/iio/magnetometer/st_magn_core.c index 62036d2a9956..8250fc322c56 100644 --- a/drivers/iio/magnetometer/st_magn_core.c +++ b/drivers/iio/magnetometer/st_magn_core.c @@ -572,6 +572,7 @@ static const struct iio_info magn_info = { static const struct iio_trigger_ops st_magn_trigger_ops = { .owner = THIS_MODULE, .set_trigger_state = ST_MAGN_TRIGGER_SET_STATE, + .validate_device = st_sensors_validate_device, }; #define ST_MAGN_TRIGGER_OPS (&st_magn_trigger_ops) #else diff --git a/drivers/iio/pressure/st_pressure_buffer.c b/drivers/iio/pressure/st_pressure_buffer.c index 2ff53f222352..99468d0a64e7 100644 --- a/drivers/iio/pressure/st_pressure_buffer.c +++ b/drivers/iio/pressure/st_pressure_buffer.c @@ -82,7 +82,7 @@ static const struct iio_buffer_setup_ops st_press_buffer_setup_ops = { int st_press_allocate_ring(struct iio_dev *indio_dev) { - return iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time, + return iio_triggered_buffer_setup(indio_dev, NULL, &st_sensors_trigger_handler, &st_press_buffer_setup_ops); } diff --git a/drivers/iio/pressure/st_pressure_core.c b/drivers/iio/pressure/st_pressure_core.c index 257b58ac6779..92a118c3c4ac 100644 --- a/drivers/iio/pressure/st_pressure_core.c +++ b/drivers/iio/pressure/st_pressure_core.c @@ -445,6 +445,7 @@ static const struct iio_info press_info = { static const struct iio_trigger_ops st_press_trigger_ops = { .owner = THIS_MODULE, .set_trigger_state = ST_PRESS_TRIGGER_SET_STATE, + .validate_device = st_sensors_validate_device, }; #define ST_PRESS_TRIGGER_OPS (&st_press_trigger_ops) #else diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h index d029ffac0d69..99403b19092f 100644 --- a/include/linux/iio/common/st_sensors.h +++ b/include/linux/iio/common/st_sensors.h @@ -223,6 +223,8 @@ struct st_sensor_settings { * @get_irq_data_ready: Function to get the IRQ used for data ready signal. * @tf: Transfer function structure used by I/O operations. * @tb: Transfer buffers and mutex used by I/O operations. + * @hw_irq_trigger: if we're using the hardware interrupt on the sensor. + * @hw_timestamp: Latest timestamp from the interrupt handler, when in use. */ struct st_sensor_data { struct device *dev; @@ -247,6 +249,9 @@ struct st_sensor_data { const struct st_sensor_transfer_function *tf; struct st_sensor_transfer_buffer tb; + + bool hw_irq_trigger; + s64 hw_timestamp; }; #ifdef CONFIG_IIO_BUFFER @@ -260,7 +265,8 @@ int st_sensors_allocate_trigger(struct iio_dev *indio_dev, const struct iio_trigger_ops *trigger_ops); void st_sensors_deallocate_trigger(struct iio_dev *indio_dev); - +int st_sensors_validate_device(struct iio_trigger *trig, + struct iio_dev *indio_dev); #else static inline int st_sensors_allocate_trigger(struct iio_dev *indio_dev, const struct iio_trigger_ops *trigger_ops) @@ -271,6 +277,7 @@ static inline void st_sensors_deallocate_trigger(struct iio_dev *indio_dev) { return; } +#define st_sensors_validate_device NULL #endif int st_sensors_init_sensor(struct iio_dev *indio_dev,