From: Matthieu CASTET Date: Tue, 6 Nov 2012 10:51:44 +0000 (+0100) Subject: mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=64b37b2a63eb2f80b65c7185f0013f8ffc637ae3;p=GitHub%2Fmoto-9609%2Fandroid_kernel_motorola_exynos9610.git mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width The driver call nand_scan_ident in 8 bit mode, then readid or onfi detection are done (and detect bus width). The driver should update its bus width before calling nand_scan_tail. This work because readid and onfi are read work 8 byte mode. Note that nand_scan_ident send command (NAND_CMD_RESET, NAND_CMD_READID, NAND_CMD_PARAM), address and read data The ONFI specificication is not very clear for x16 device if high byte of address should be driven to 0, but according to [1] it should be ok to not drive it during autodetection. [1] 3.3.2. Target Initialization [...] The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus. The host shall not issue commands that use a word data width on x16 devices until the host determines the device supports a 16-bit data bus width in the parameter page. Signed-off-by: Matthieu CASTET Signed-off-by: Artem Bityutskiy --- diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 6f58e1633e2f..5851c51ac2df 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -3250,11 +3250,15 @@ ident_done: break; } - /* - * Check, if buswidth is correct. Hardware drivers should set - * chip correct! - */ - if (busw != (chip->options & NAND_BUSWIDTH_16)) { + if (chip->options & NAND_BUSWIDTH_AUTO) { + WARN_ON(chip->options & NAND_BUSWIDTH_16); + chip->options |= busw; + nand_set_defaults(chip, busw); + } else if (busw != (chip->options & NAND_BUSWIDTH_16)) { + /* + * Check, if buswidth is correct. Hardware drivers should set + * chip correct! + */ pr_info("NAND device: Manufacturer ID:" " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, *dev_id, nand_manuf_ids[maf_idx].name, mtd->name); diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 9d8a6048aacd..7ccb3c59ed60 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -219,6 +219,13 @@ typedef enum { #define NAND_OWN_BUFFERS 0x00020000 /* Chip may not exist, so silence any errors in scan */ #define NAND_SCAN_SILENT_NODEV 0x00040000 +/* + * Autodetect nand buswidth with readid/onfi. + * This suppose the driver will configure the hardware in 8 bits mode + * when calling nand_scan_ident, and update its configuration + * before calling nand_scan_tail. + */ +#define NAND_BUSWIDTH_AUTO 0x00080000 /* Options set by nand scan */ /* Nand scan has allocated controller struct */