From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Sun, 24 Jul 2011 17:59:20 +0000 (-0300)
Subject: [media] drxk: Add support for parallel mode and prints mpeg mode
X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=534e04810304a9c6715220b392aa387197d5fa15;p=GitHub%2FLineageOS%2FG12%2Fandroid_kernel_amlogic_linux-4.9.git

[media] drxk: Add support for parallel mode and prints mpeg mode

While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.

Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---

diff --git a/drivers/media/dvb/frontends/drxk.h b/drivers/media/dvb/frontends/drxk.h
index e6d42e271b89..870432ffcce1 100644
--- a/drivers/media/dvb/frontends/drxk.h
+++ b/drivers/media/dvb/frontends/drxk.h
@@ -8,6 +8,8 @@
  * struct drxk_config - Configure the initial parameters for DRX-K
  *
  * adr:			I2C Address of the DRX-K
+ * parallel_ts:		true means that the device uses parallel TS,
+ * 			Serial otherwise.
  * single_master:	Device is on the single master mode
  * no_i2c_bridge:	Don't switch the I2C bridge to talk with tuner
  * antenna_gpio:	GPIO bit used to control the antenna
@@ -22,6 +24,7 @@ struct drxk_config {
 	u8	adr;
 	bool	single_master;
 	bool	no_i2c_bridge;
+	bool	parallel_ts;
 
 	bool	antenna_dvbt;
 	u16	antenna_gpio;
diff --git a/drivers/media/dvb/frontends/drxk_hard.c b/drivers/media/dvb/frontends/drxk_hard.c
index 817d3ec2be49..c8213f61effb 100644
--- a/drivers/media/dvb/frontends/drxk_hard.c
+++ b/drivers/media/dvb/frontends/drxk_hard.c
@@ -660,7 +660,6 @@ static int init_state(struct drxk_state *state)
 	/* io_pad_cfg_mode output mode is drive always */
 	/* io_pad_cfg_drive is set to power 2 (23 mA) */
 	u32 ulGPIOCfg = 0x0113;
-	u32 ulSerialMode = 1;
 	u32 ulInvertTSClock = 0;
 	u32 ulTSDataStrength = DRXK_MPEG_SERIAL_OUTPUT_PIN_DRIVE_STRENGTH;
 	u32 ulTSClockkStrength = DRXK_MPEG_OUTPUT_CLK_DRIVE_STRENGTH;
@@ -811,8 +810,6 @@ static int init_state(struct drxk_state *state)
 	/* MPEG output configuration */
 	state->m_enableMPEGOutput = true;	/* If TRUE; enable MPEG ouput */
 	state->m_insertRSByte = false;	/* If TRUE; insert RS byte */
-	state->m_enableParallel = true;	/* If TRUE;
-					   parallel out otherwise serial */
 	state->m_invertDATA = false;	/* If TRUE; invert DATA signals */
 	state->m_invertERR = false;	/* If TRUE; invert ERR signal */
 	state->m_invertSTR = false;	/* If TRUE; invert STR signals */
@@ -857,8 +854,6 @@ static int init_state(struct drxk_state *state)
 	state->m_bPowerDown = false;
 	state->m_currentPowerMode = DRX_POWER_DOWN;
 
-	state->m_enableParallel = (ulSerialMode == 0);
-
 	state->m_rfmirror = (ulRfMirror == 0);
 	state->m_IfAgcPol = false;
 	return 0;
@@ -1195,7 +1190,9 @@ static int MPEGTSConfigurePins(struct drxk_state *state, bool mpegEnable)
 	u16 sioPdrMclkCfg = 0;
 	u16 sioPdrMdxCfg = 0;
 
-	dprintk(1, "\n");
+	dprintk(1, ": mpeg %s, %s mode\n",
+		mpegEnable ? "enable" : "disable",
+		state->m_enableParallel ? "parallel" : "serial");
 
 	/* stop lock indicator process */
 	status = write16(state, SCU_RAM_GPIO__A, SCU_RAM_GPIO_HW_LOCK_IND_DISABLE);
@@ -6432,6 +6429,11 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
 	state->antenna_dvbt = config->antenna_dvbt;
 	state->m_ChunkSize = config->chunk_size;
 
+	if (config->parallel_ts)
+		state->m_enableParallel = true;
+	else
+		state->m_enableParallel = false;
+
 	/* NOTE: as more UIO bits will be used, add them to the mask */
 	state->UIO_mask = config->antenna_gpio;