From: Bryan Buckley Date: Fri, 30 Sep 2011 18:05:55 +0000 (-0700) Subject: ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1 X-Git-Url: https://git.stricted.de/?a=commitdiff_plain;h=3696d303d6a39f916f9ace37d79e3db7937c68a7;p=GitHub%2Fmoto-9609%2Fandroid_kernel_motorola_exynos9610.git ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1 Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance with the control module programming guide. This fixes a bug where if trying to use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be affected by a changing SDMMC1_VDDS. Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever SDMMC1_VDDS ramps up/down or changes for cell protection purposes. MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore they can operate independently. Signed-off-by: Bryan Buckley Acked-by: Kishore Kadiyala Tested-by: Balaji T K Signed-off-by: Tony Lindgren --- diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index a9b45c76e1d3..097a42d81e59 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -137,8 +137,7 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot, */ reg = omap4_ctrl_pad_readl(control_pbias_offset); reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } @@ -156,8 +155,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, else reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK; reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); timeout = jiffies + msecs_to_jiffies(5); @@ -171,16 +169,14 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) { pr_err("Pbias Voltage is not same as LDO\n"); /* Caution : On VMODE_ERROR Power Down MMC IO */ - reg &= ~(OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + reg &= ~(OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } } else { reg = omap4_ctrl_pad_readl(control_pbias_offset); reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_MMC1_PBIASLITE_VMODE_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PBIASLITE_VMODE_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } }