--- /dev/null
+/*
+ * drivers/mtd/nand/pxa3xx_nand.c
+ *
+ * Copyright © 2005 Intel Corporation
+ * Copyright © 2006 Marvell International Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/dma.h>
+
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/pxa3xx_nand.h>
+
+#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
+
+/* registers and bit definitions */
+#define NDCR (0x00) /* Control register */
+#define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */
+#define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */
+#define NDSR (0x14) /* Status Register */
+#define NDPCR (0x18) /* Page Count Register */
+#define NDBDR0 (0x1C) /* Bad Block Register 0 */
+#define NDBDR1 (0x20) /* Bad Block Register 1 */
+#define NDDB (0x40) /* Data Buffer */
+#define NDCB0 (0x48) /* Command Buffer0 */
+#define NDCB1 (0x4C) /* Command Buffer1 */
+#define NDCB2 (0x50) /* Command Buffer2 */
+
+#define NDCR_SPARE_EN (0x1 << 31)
+#define NDCR_ECC_EN (0x1 << 30)
+#define NDCR_DMA_EN (0x1 << 29)
+#define NDCR_ND_RUN (0x1 << 28)
+#define NDCR_DWIDTH_C (0x1 << 27)
+#define NDCR_DWIDTH_M (0x1 << 26)
+#define NDCR_PAGE_SZ (0x1 << 24)
+#define NDCR_NCSX (0x1 << 23)
+#define NDCR_ND_MODE (0x3 << 21)
+#define NDCR_NAND_MODE (0x0)
+#define NDCR_CLR_PG_CNT (0x1 << 20)
+#define NDCR_CLR_ECC (0x1 << 19)
+#define NDCR_RD_ID_CNT_MASK (0x7 << 16)
+#define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK)
+
+#define NDCR_RA_START (0x1 << 15)
+#define NDCR_PG_PER_BLK (0x1 << 14)
+#define NDCR_ND_ARB_EN (0x1 << 12)
+
+#define NDSR_MASK (0xfff)
+#define NDSR_RDY (0x1 << 11)
+#define NDSR_CS0_PAGED (0x1 << 10)
+#define NDSR_CS1_PAGED (0x1 << 9)
+#define NDSR_CS0_CMDD (0x1 << 8)
+#define NDSR_CS1_CMDD (0x1 << 7)
+#define NDSR_CS0_BBD (0x1 << 6)
+#define NDSR_CS1_BBD (0x1 << 5)
+#define NDSR_DBERR (0x1 << 4)
+#define NDSR_SBERR (0x1 << 3)
+#define NDSR_WRDREQ (0x1 << 2)
+#define NDSR_RDDREQ (0x1 << 1)
+#define NDSR_WRCMDREQ (0x1)
+
+#define NDCB0_AUTO_RS (0x1 << 25)
+#define NDCB0_CSEL (0x1 << 24)
+#define NDCB0_CMD_TYPE_MASK (0x7 << 21)
+#define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK)
+#define NDCB0_NC (0x1 << 20)
+#define NDCB0_DBC (0x1 << 19)
+#define NDCB0_ADDR_CYC_MASK (0x7 << 16)
+#define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK)
+#define NDCB0_CMD2_MASK (0xff << 8)
+#define NDCB0_CMD1_MASK (0xff)
+#define NDCB0_ADDR_CYC_SHIFT (16)
+
+/* dma-able I/O address for the NAND data and commands */
+#define NDCB0_DMA_ADDR (0x43100048)
+#define NDDB_DMA_ADDR (0x43100040)
+
+/* macros for registers read/write */
+#define nand_writel(info, off, val) \
+ __raw_writel((val), (info)->mmio_base + (off))
+
+#define nand_readl(info, off) \
+ __raw_readl((info)->mmio_base + (off))
+
+/* error code and state */
+enum {
+ ERR_NONE = 0,
+ ERR_DMABUSERR = -1,
+ ERR_SENDCMD = -2,
+ ERR_DBERR = -3,
+ ERR_BBERR = -4,
+};
+
+enum {
+ STATE_READY = 0,
+ STATE_CMD_HANDLE,
+ STATE_DMA_READING,
+ STATE_DMA_WRITING,
+ STATE_DMA_DONE,
+ STATE_PIO_READING,
+ STATE_PIO_WRITING,
+};
+
+struct pxa3xx_nand_timing {
+ unsigned int tCH; /* Enable signal hold time */
+ unsigned int tCS; /* Enable signal setup time */
+ unsigned int tWH; /* ND_nWE high duration */
+ unsigned int tWP; /* ND_nWE pulse time */
+ unsigned int tRH; /* ND_nRE high duration */
+ unsigned int tRP; /* ND_nRE pulse width */
+ unsigned int tR; /* ND_nWE high to ND_nRE low for read */
+ unsigned int tWHR; /* ND_nWE high to ND_nRE low for status read */
+ unsigned int tAR; /* ND_ALE low to ND_nRE low delay */
+};
+
+struct pxa3xx_nand_cmdset {
+ uint16_t read1;
+ uint16_t read2;
+ uint16_t program;
+ uint16_t read_status;
+ uint16_t read_id;
+ uint16_t erase;
+ uint16_t reset;
+ uint16_t lock;
+ uint16_t unlock;
+ uint16_t lock_status;
+};
+
+struct pxa3xx_nand_flash {
+ struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
+ struct pxa3xx_nand_cmdset *cmdset;
+
+ uint32_t page_per_block;/* Pages per block (PG_PER_BLK) */
+ uint32_t page_size; /* Page size in bytes (PAGE_SZ) */
+ uint32_t flash_width; /* Width of Flash memory (DWIDTH_M) */
+ uint32_t dfc_width; /* Width of flash controller(DWIDTH_C) */
+ uint32_t num_blocks; /* Number of physical blocks in Flash */
+ uint32_t chip_id;
+
+ /* NOTE: these are automatically calculated, do not define */
+ size_t oob_size;
+ size_t read_id_bytes;
+
+ unsigned int col_addr_cycles;
+ unsigned int row_addr_cycles;
+};
+
+struct pxa3xx_nand_info {
+ struct nand_chip nand_chip;
+
+ struct platform_device *pdev;
+ struct pxa3xx_nand_flash *flash_info;
+
+ struct clk *clk;
+ void __iomem *mmio_base;
+
+ unsigned int buf_start;
+ unsigned int buf_count;
+
+ /* DMA information */
+ int drcmr_dat;
+ int drcmr_cmd;
+
+ unsigned char *data_buff;
+ dma_addr_t data_buff_phys;
+ size_t data_buff_size;
+ int data_dma_ch;
+ struct pxa_dma_desc *data_desc;
+ dma_addr_t data_desc_addr;
+
+ uint32_t reg_ndcr;
+
+ /* saved column/page_addr during CMD_SEQIN */
+ int seqin_column;
+ int seqin_page_addr;
+
+ /* relate to the command */
+ unsigned int state;
+
+ int use_ecc; /* use HW ECC ? */
+ int use_dma; /* use DMA ? */
+
+ size_t data_size; /* data size in FIFO */
+ int retcode;
+ struct completion cmd_complete;
+
+ /* generated NDCBx register values */
+ uint32_t ndcb0;
+ uint32_t ndcb1;
+ uint32_t ndcb2;
+};
+
+static int use_dma = 1;
+module_param(use_dma, bool, 0444);
+MODULE_PARM_DESC(use_dma, "enable DMA for data transfering to/from NAND HW");
+
+static struct pxa3xx_nand_cmdset smallpage_cmdset = {
+ .read1 = 0x0000,
+ .read2 = 0x0050,
+ .program = 0x1080,
+ .read_status = 0x0070,
+ .read_id = 0x0090,
+ .erase = 0xD060,
+ .reset = 0x00FF,
+ .lock = 0x002A,
+ .unlock = 0x2423,
+ .lock_status = 0x007A,
+};
+
+static struct pxa3xx_nand_cmdset largepage_cmdset = {
+ .read1 = 0x3000,
+ .read2 = 0x0050,
+ .program = 0x1080,
+ .read_status = 0x0070,
+ .read_id = 0x0090,
+ .erase = 0xD060,
+ .reset = 0x00FF,
+ .lock = 0x002A,
+ .unlock = 0x2423,
+ .lock_status = 0x007A,
+};
+
+static struct pxa3xx_nand_timing samsung512MbX16_timing = {
+ .tCH = 10,
+ .tCS = 0,
+ .tWH = 20,
+ .tWP = 40,
+ .tRH = 30,
+ .tRP = 40,
+ .tR = 11123,
+ .tWHR = 110,
+ .tAR = 10,
+};
+
+static struct pxa3xx_nand_flash samsung512MbX16 = {
+ .timing = &samsung512MbX16_timing,
+ .cmdset = &smallpage_cmdset,
+ .page_per_block = 32,
+ .page_size = 512,
+ .flash_width = 16,
+ .dfc_width = 16,
+ .num_blocks = 4096,
+ .chip_id = 0x46ec,
+};
+
+static struct pxa3xx_nand_timing micron_timing = {
+ .tCH = 10,
+ .tCS = 25,
+ .tWH = 15,
+ .tWP = 25,
+ .tRH = 15,
+ .tRP = 25,
+ .tR = 25000,
+ .tWHR = 60,
+ .tAR = 10,
+};
+
+static struct pxa3xx_nand_flash micron1GbX8 = {
+ .timing = µn_timing,
+ .cmdset = &largepage_cmdset,
+ .page_per_block = 64,
+ .page_size = 2048,
+ .flash_width = 8,
+ .dfc_width = 8,
+ .num_blocks = 1024,
+ .chip_id = 0xa12c,
+};
+
+static struct pxa3xx_nand_flash micron1GbX16 = {
+ .timing = µn_timing,
+ .cmdset = &largepage_cmdset,
+ .page_per_block = 64,
+ .page_size = 2048,
+ .flash_width = 16,
+ .dfc_width = 16,
+ .num_blocks = 1024,
+ .chip_id = 0xb12c,
+};
+
+static struct pxa3xx_nand_flash *builtin_flash_types[] = {
+ &samsung512MbX16,
+ µn1GbX8,
+ µn1GbX16,
+};
+
+#define NDTR0_tCH(c) (min((c), 7) << 19)
+#define NDTR0_tCS(c) (min((c), 7) << 16)
+#define NDTR0_tWH(c) (min((c), 7) << 11)
+#define NDTR0_tWP(c) (min((c), 7) << 8)
+#define NDTR0_tRH(c) (min((c), 7) << 3)
+#define NDTR0_tRP(c) (min((c), 7) << 0)
+
+#define NDTR1_tR(c) (min((c), 65535) << 16)
+#define NDTR1_tWHR(c) (min((c), 15) << 4)
+#define NDTR1_tAR(c) (min((c), 15) << 0)
+
+/* convert nano-seconds to nand flash controller clock cycles */
+#define ns2cycle(ns, clk) (int)(((ns) * (clk / 1000000) / 1000) + 1)
+
+static void pxa3xx_nand_set_timing(struct pxa3xx_nand_info *info,
+ struct pxa3xx_nand_timing *t)
+{
+ unsigned long nand_clk = clk_get_rate(info->clk);
+ uint32_t ndtr0, ndtr1;
+
+ ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) |
+ NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) |
+ NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) |
+ NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) |
+ NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) |
+ NDTR0_tRP(ns2cycle(t->tRP, nand_clk));
+
+ ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) |
+ NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
+ NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
+
+ nand_writel(info, NDTR0CS0, ndtr0);
+ nand_writel(info, NDTR1CS0, ndtr1);
+}
+
+#define WAIT_EVENT_TIMEOUT 10
+
+static int wait_for_event(struct pxa3xx_nand_info *info, uint32_t event)
+{
+ int timeout = WAIT_EVENT_TIMEOUT;
+ uint32_t ndsr;
+
+ while (timeout--) {
+ ndsr = nand_readl(info, NDSR) & NDSR_MASK;
+ if (ndsr & event) {
+ nand_writel(info, NDSR, ndsr);
+ return 0;
+ }
+ udelay(10);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
+ uint16_t cmd, int column, int page_addr)
+{
+ struct pxa3xx_nand_flash *f = info->flash_info;
+ struct pxa3xx_nand_cmdset *cmdset = f->cmdset;
+
+ /* calculate data size */
+ switch (f->page_size) {
+ case 2048:
+ info->data_size = (info->use_ecc) ? 2088 : 2112;
+ break;
+ case 512:
+ info->data_size = (info->use_ecc) ? 520 : 528;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* generate values for NDCBx registers */
+ info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
+ info->ndcb1 = 0;
+ info->ndcb2 = 0;
+ info->ndcb0 |= NDCB0_ADDR_CYC(f->row_addr_cycles + f->col_addr_cycles);
+
+ if (f->col_addr_cycles == 2) {
+ /* large block, 2 cycles for column address
+ * row address starts from 3rd cycle
+ */
+ info->ndcb1 |= (page_addr << 16) | (column & 0xffff);
+ if (f->row_addr_cycles == 3)
+ info->ndcb2 = (page_addr >> 16) & 0xff;
+ } else
+ /* small block, 1 cycles for column address
+ * row address starts from 2nd cycle
+ */
+ info->ndcb1 = (page_addr << 8) | (column & 0xff);
+
+ if (cmd == cmdset->program)
+ info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS;
+
+ return 0;
+}
+
+static int prepare_erase_cmd(struct pxa3xx_nand_info *info,
+ uint16_t cmd, int page_addr)
+{
+ info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
+ info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3);
+ info->ndcb1 = page_addr;
+ info->ndcb2 = 0;
+ return 0;
+}
+
+static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
+{
+ struct pxa3xx_nand_cmdset *cmdset = info->flash_info->cmdset;
+
+ info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
+ info->ndcb1 = 0;
+ info->ndcb2 = 0;
+
+ if (cmd == cmdset->read_id) {
+ info->ndcb0 |= NDCB0_CMD_TYPE(3);
+ info->data_size = 8;
+ } else if (cmd == cmdset->read_status) {
+ info->ndcb0 |= NDCB0_CMD_TYPE(4);
+ info->data_size = 8;
+ } else if (cmd == cmdset->reset || cmd == cmdset->lock ||
+ cmd == cmdset->unlock) {
+ info->ndcb0 |= NDCB0_CMD_TYPE(5);
+ } else
+ return -EINVAL;
+
+ return 0;
+}
+
+static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
+{
+ uint32_t ndcr;
+
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr & ~int_mask);
+}
+
+static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
+{
+ uint32_t ndcr;
+
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr | int_mask);
+}
+
+/* NOTE: it is a must to set ND_RUN firstly, then write command buffer
+ * otherwise, it does not work
+ */
+static int write_cmd(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+
+ /* clear status bits and run */
+ nand_writel(info, NDSR, NDSR_MASK);
+
+ ndcr = info->reg_ndcr;
+
+ ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
+ ndcr |= info->use_dma ? NDCR_DMA_EN : 0;
+ ndcr |= NDCR_ND_RUN;
+
+ nand_writel(info, NDCR, ndcr);
+
+ if (wait_for_event(info, NDSR_WRCMDREQ)) {
+ printk(KERN_ERR "timed out writing command\n");
+ return -ETIMEDOUT;
+ }
+
+ nand_writel(info, NDCB0, info->ndcb0);
+ nand_writel(info, NDCB0, info->ndcb1);
+ nand_writel(info, NDCB0, info->ndcb2);
+ return 0;
+}
+
+static int handle_data_pio(struct pxa3xx_nand_info *info)
+{
+ int ret, timeout = CHIP_DELAY_TIMEOUT;
+
+ switch (info->state) {
+ case STATE_PIO_WRITING:
+ __raw_writesl(info->mmio_base + NDDB, info->data_buff,
+ info->data_size << 2);
+
+ enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
+
+ ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
+ if (!ret) {
+ printk(KERN_ERR "program command time out\n");
+ return -1;
+ }
+ break;
+ case STATE_PIO_READING:
+ __raw_readsl(info->mmio_base + NDDB, info->data_buff,
+ info->data_size << 2);
+ break;
+ default:
+ printk(KERN_ERR "%s: invalid state %d\n", __FUNCTION__,
+ info->state);
+ return -EINVAL;
+ }
+
+ info->state = STATE_READY;
+ return 0;
+}
+
+static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out)
+{
+ struct pxa_dma_desc *desc = info->data_desc;
+ int dma_len = ALIGN(info->data_size, 32);
+
+ desc->ddadr = DDADR_STOP;
+ desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len;
+
+ if (dir_out) {
+ desc->dsadr = info->data_buff_phys;
+ desc->dtadr = NDDB_DMA_ADDR;
+ desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG;
+ } else {
+ desc->dtadr = info->data_buff_phys;
+ desc->dsadr = NDDB_DMA_ADDR;
+ desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC;
+ }
+
+ DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch;
+ DDADR(info->data_dma_ch) = info->data_desc_addr;
+ DCSR(info->data_dma_ch) |= DCSR_RUN;
+}
+
+static void pxa3xx_nand_data_dma_irq(int channel, void *data)
+{
+ struct pxa3xx_nand_info *info = data;
+ uint32_t dcsr;
+
+ dcsr = DCSR(channel);
+ DCSR(channel) = dcsr;
+
+ if (dcsr & DCSR_BUSERR) {
+ info->retcode = ERR_DMABUSERR;
+ complete(&info->cmd_complete);
+ }
+
+ if (info->state == STATE_DMA_WRITING) {
+ info->state = STATE_DMA_DONE;
+ enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
+ } else {
+ info->state = STATE_READY;
+ complete(&info->cmd_complete);
+ }
+}
+
+static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
+{
+ struct pxa3xx_nand_info *info = devid;
+ unsigned int status;
+
+ status = nand_readl(info, NDSR);
+
+ if (status & (NDSR_RDDREQ | NDSR_DBERR)) {
+ if (status & NDSR_DBERR)
+ info->retcode = ERR_DBERR;
+
+ disable_int(info, NDSR_RDDREQ | NDSR_DBERR);
+
+ if (info->use_dma) {
+ info->state = STATE_DMA_READING;
+ start_data_dma(info, 0);
+ } else {
+ info->state = STATE_PIO_READING;
+ complete(&info->cmd_complete);
+ }
+ } else if (status & NDSR_WRDREQ) {
+ disable_int(info, NDSR_WRDREQ);
+ if (info->use_dma) {
+ info->state = STATE_DMA_WRITING;
+ start_data_dma(info, 1);
+ } else {
+ info->state = STATE_PIO_WRITING;
+ complete(&info->cmd_complete);
+ }
+ } else if (status & (NDSR_CS0_BBD | NDSR_CS0_CMDD)) {
+ if (status & NDSR_CS0_BBD)
+ info->retcode = ERR_BBERR;
+
+ disable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
+ info->state = STATE_READY;
+ complete(&info->cmd_complete);
+ }
+ nand_writel(info, NDSR, status);
+ return IRQ_HANDLED;
+}
+
+static int pxa3xx_nand_do_cmd(struct pxa3xx_nand_info *info, uint32_t event)
+{
+ uint32_t ndcr;
+ int ret, timeout = CHIP_DELAY_TIMEOUT;
+
+ if (write_cmd(info)) {
+ info->retcode = ERR_SENDCMD;
+ goto fail_stop;
+ }
+
+ info->state = STATE_CMD_HANDLE;
+
+ enable_int(info, event);
+
+ ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
+ if (!ret) {
+ printk(KERN_ERR "command execution timed out\n");
+ info->retcode = ERR_SENDCMD;
+ goto fail_stop;
+ }
+
+ if (info->use_dma == 0 && info->data_size > 0)
+ if (handle_data_pio(info))
+ goto fail_stop;
+
+ return 0;
+
+fail_stop:
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
+ udelay(10);
+ return -ETIMEDOUT;
+}
+
+static int pxa3xx_nand_dev_ready(struct mtd_info *mtd)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ return (nand_readl(info, NDSR) & NDSR_RDY) ? 1 : 0;
+}
+
+static inline int is_buf_blank(uint8_t *buf, size_t len)
+{
+ for (; len > 0; len--)
+ if (*buf++ != 0xff)
+ return 0;
+ return 1;
+}
+
+static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr )
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ struct pxa3xx_nand_flash * flash_info = info->flash_info;
+ struct pxa3xx_nand_cmdset *cmdset = flash_info->cmdset;
+ int ret;
+
+ info->use_dma = (use_dma) ? 1 : 0;
+ info->use_ecc = 0;
+ info->data_size = 0;
+ info->state = STATE_READY;
+
+ init_completion(&info->cmd_complete);
+
+ switch (command) {
+ case NAND_CMD_READOOB:
+ /* disable HW ECC to get all the OOB data */
+ info->buf_count = mtd->writesize + mtd->oobsize;
+ info->buf_start = mtd->writesize + column;
+
+ if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr))
+ break;
+
+ pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR);
+
+ /* We only are OOB, so if the data has error, does not matter */
+ if (info->retcode == ERR_DBERR)
+ info->retcode = ERR_NONE;
+ break;
+
+ case NAND_CMD_READ0:
+ info->use_ecc = 1;
+ info->retcode = ERR_NONE;
+ info->buf_start = column;
+ info->buf_count = mtd->writesize + mtd->oobsize;
+ memset(info->data_buff, 0xFF, info->buf_count);
+
+ if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr))
+ break;
+
+ pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR);
+
+ if (info->retcode == ERR_DBERR) {
+ /* for blank page (all 0xff), HW will calculate its ECC as
+ * 0, which is different from the ECC information within
+ * OOB, ignore such double bit errors
+ */
+ if (is_buf_blank(info->data_buff, mtd->writesize))
+ info->retcode = ERR_NONE;
+ }
+ break;
+ case NAND_CMD_SEQIN:
+ info->buf_start = column;
+ info->buf_count = mtd->writesize + mtd->oobsize;
+ memset(info->data_buff, 0xff, info->buf_count);
+
+ /* save column/page_addr for next CMD_PAGEPROG */
+ info->seqin_column = column;
+ info->seqin_page_addr = page_addr;
+ break;
+ case NAND_CMD_PAGEPROG:
+ info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1;
+
+ if (prepare_read_prog_cmd(info, cmdset->program,
+ info->seqin_column, info->seqin_page_addr))
+ break;
+
+ pxa3xx_nand_do_cmd(info, NDSR_WRDREQ);
+ break;
+ case NAND_CMD_ERASE1:
+ if (prepare_erase_cmd(info, cmdset->erase, page_addr))
+ break;
+
+ pxa3xx_nand_do_cmd(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
+ break;
+ case NAND_CMD_ERASE2:
+ break;
+ case NAND_CMD_READID:
+ case NAND_CMD_STATUS:
+ info->use_dma = 0; /* force PIO read */
+ info->buf_start = 0;
+ info->buf_count = (command == NAND_CMD_READID) ?
+ flash_info->read_id_bytes : 1;
+
+ if (prepare_other_cmd(info, (command == NAND_CMD_READID) ?
+ cmdset->read_id : cmdset->read_status))
+ break;
+
+ pxa3xx_nand_do_cmd(info, NDSR_RDDREQ);
+ break;
+ case NAND_CMD_RESET:
+ if (prepare_other_cmd(info, cmdset->reset))
+ break;
+
+ ret = pxa3xx_nand_do_cmd(info, NDSR_CS0_CMDD);
+ if (ret == 0) {
+ int timeout = 2;
+ uint32_t ndcr;
+
+ while (timeout--) {
+ if (nand_readl(info, NDSR) & NDSR_RDY)
+ break;
+ msleep(10);
+ }
+
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
+ }
+ break;
+ default:
+ printk(KERN_ERR "non-supported command.\n");
+ break;
+ }
+
+ if (info->retcode == ERR_DBERR) {
+ printk(KERN_ERR "double bit error @ page %08x\n", page_addr);
+ info->retcode = ERR_NONE;
+ }
+}
+
+static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ char retval = 0xFF;
+
+ if (info->buf_start < info->buf_count)
+ /* Has just send a new command? */
+ retval = info->data_buff[info->buf_start++];
+
+ return retval;
+}
+
+static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ u16 retval = 0xFFFF;
+
+ if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
+ retval = *((u16 *)(info->data_buff+info->buf_start));
+ info->buf_start += 2;
+ }
+ return retval;
+}
+
+static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
+
+ memcpy(buf, info->data_buff + info->buf_start, real_len);
+ info->buf_start += real_len;
+}
+
+static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
+ const uint8_t *buf, int len)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
+
+ memcpy(info->data_buff + info->buf_start, buf, real_len);
+ info->buf_start += real_len;
+}
+
+static int pxa3xx_nand_verify_buf(struct mtd_info *mtd,
+ const uint8_t *buf, int len)
+{
+ return 0;
+}
+
+static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
+{
+ return;
+}
+
+static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+
+ /* pxa3xx_nand_send_command has waited for command complete */
+ if (this->state == FL_WRITING || this->state == FL_ERASING) {
+ if (info->retcode == ERR_NONE)
+ return 0;
+ else {
+ /*
+ * any error make it return 0x01 which will tell
+ * the caller the erase and write fail
+ */
+ return 0x01;
+ }
+ }
+
+ return 0;
+}
+
+static void pxa3xx_nand_ecc_hwctl(struct mtd_info *mtd, int mode)
+{
+ return;
+}
+
+static int pxa3xx_nand_ecc_calculate(struct mtd_info *mtd,
+ const uint8_t *dat, uint8_t *ecc_code)
+{
+ return 0;
+}
+
+static int pxa3xx_nand_ecc_correct(struct mtd_info *mtd,
+ uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ /*
+ * Any error include ERR_SEND_CMD, ERR_DBERR, ERR_BUSERR, we
+ * consider it as a ecc error which will tell the caller the
+ * read fail We have distinguish all the errors, but the
+ * nand_read_ecc only check this function return value
+ */
+ if (info->retcode != ERR_NONE)
+ return -1;
+
+ return 0;
+}
+
+static int __readid(struct pxa3xx_nand_info *info, uint32_t *id)
+{
+ struct pxa3xx_nand_flash *f = info->flash_info;
+ struct pxa3xx_nand_cmdset *cmdset = f->cmdset;
+ uint32_t ndcr;
+ uint8_t id_buff[8];
+
+ if (prepare_other_cmd(info, cmdset->read_id)) {
+ printk(KERN_ERR "failed to prepare command\n");
+ return -EINVAL;
+ }
+
+ /* Send command */
+ if (write_cmd(info))
+ goto fail_timeout;
+
+ /* Wait for CMDDM(command done successfully) */
+ if (wait_for_event(info, NDSR_RDDREQ))
+ goto fail_timeout;
+
+ __raw_readsl(info->mmio_base + NDDB, id_buff, 2);
+ *id = id_buff[0] | (id_buff[1] << 8);
+ return 0;
+
+fail_timeout:
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
+ udelay(10);
+ return -ETIMEDOUT;
+}
+
+static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
+ struct pxa3xx_nand_flash *f)
+{
+ struct platform_device *pdev = info->pdev;
+ struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
+ uint32_t ndcr = 0x00000FFF; /* disable all interrupts */
+
+ if (f->page_size != 2048 && f->page_size != 512)
+ return -EINVAL;
+
+ if (f->flash_width != 16 && f->flash_width != 8)
+ return -EINVAL;
+
+ /* calculate flash information */
+ f->oob_size = (f->page_size == 2048) ? 64 : 16;
+ f->read_id_bytes = (f->page_size == 2048) ? 4 : 2;
+
+ /* calculate addressing information */
+ f->col_addr_cycles = (f->page_size == 2048) ? 2 : 1;
+
+ if (f->num_blocks * f->page_per_block > 65536)
+ f->row_addr_cycles = 3;
+ else
+ f->row_addr_cycles = 2;
+
+ ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
+ ndcr |= (f->col_addr_cycles == 2) ? NDCR_RA_START : 0;
+ ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0;
+ ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0;
+ ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0;
+ ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
+
+ ndcr |= NDCR_RD_ID_CNT(f->read_id_bytes);
+ ndcr |= NDCR_SPARE_EN; /* enable spare by default */
+
+ info->reg_ndcr = ndcr;
+
+ pxa3xx_nand_set_timing(info, f->timing);
+ info->flash_info = f;
+ return 0;
+}
+
+static int pxa3xx_nand_detect_flash(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_flash *f;
+ uint32_t id;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(builtin_flash_types); i++) {
+
+ f = builtin_flash_types[i];
+
+ if (pxa3xx_nand_config_flash(info, f))
+ continue;
+
+ if (__readid(info, &id))
+ continue;
+
+ if (id == f->chip_id)
+ return 0;
+ }
+
+ return -ENODEV;
+}
+
+/* the maximum possible buffer size for large page with OOB data
+ * is: 2048 + 64 = 2112 bytes, allocate a page here for both the
+ * data buffer and the DMA descriptor
+ */
+#define MAX_BUFF_SIZE PAGE_SIZE
+
+static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
+{
+ struct platform_device *pdev = info->pdev;
+ int data_desc_offset = MAX_BUFF_SIZE - sizeof(struct pxa_dma_desc);
+
+ if (use_dma == 0) {
+ info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL);
+ if (info->data_buff == NULL)
+ return -ENOMEM;
+ return 0;
+ }
+
+ info->data_buff = dma_alloc_coherent(&pdev->dev, MAX_BUFF_SIZE,
+ &info->data_buff_phys, GFP_KERNEL);
+ if (info->data_buff == NULL) {
+ dev_err(&pdev->dev, "failed to allocate dma buffer\n");
+ return -ENOMEM;
+ }
+
+ info->data_buff_size = MAX_BUFF_SIZE;
+ info->data_desc = (void *)info->data_buff + data_desc_offset;
+ info->data_desc_addr = info->data_buff_phys + data_desc_offset;
+
+ info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW,
+ pxa3xx_nand_data_dma_irq, info);
+ if (info->data_dma_ch < 0) {
+ dev_err(&pdev->dev, "failed to request data dma\n");
+ dma_free_coherent(&pdev->dev, info->data_buff_size,
+ info->data_buff, info->data_buff_phys);
+ return info->data_dma_ch;
+ }
+
+ return 0;
+}
+
+static struct nand_ecclayout hw_smallpage_ecclayout = {
+ .eccbytes = 6,
+ .eccpos = {8, 9, 10, 11, 12, 13 },
+ .oobfree = { {2, 6} }
+};
+
+static struct nand_ecclayout hw_largepage_ecclayout = {
+ .eccbytes = 24,
+ .eccpos = {
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63},
+ .oobfree = { {2, 38} }
+};
+
+static void pxa3xx_nand_init_mtd(struct mtd_info *mtd,
+ struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_flash *f = info->flash_info;
+ struct nand_chip *this = &info->nand_chip;
+
+ this->options = (f->flash_width == 16) ? NAND_BUSWIDTH_16: 0;
+
+ this->waitfunc = pxa3xx_nand_waitfunc;
+ this->select_chip = pxa3xx_nand_select_chip;
+ this->dev_ready = pxa3xx_nand_dev_ready;
+ this->cmdfunc = pxa3xx_nand_cmdfunc;
+ this->read_word = pxa3xx_nand_read_word;
+ this->read_byte = pxa3xx_nand_read_byte;
+ this->read_buf = pxa3xx_nand_read_buf;
+ this->write_buf = pxa3xx_nand_write_buf;
+ this->verify_buf = pxa3xx_nand_verify_buf;
+
+ this->ecc.mode = NAND_ECC_HW;
+ this->ecc.hwctl = pxa3xx_nand_ecc_hwctl;
+ this->ecc.calculate = pxa3xx_nand_ecc_calculate;
+ this->ecc.correct = pxa3xx_nand_ecc_correct;
+ this->ecc.size = f->page_size;
+
+ if (f->page_size == 2048)
+ this->ecc.layout = &hw_largepage_ecclayout;
+ else
+ this->ecc.layout = &hw_smallpage_ecclayout;
+
+ this->chip_delay= 25;
+}
+
+static int pxa3xx_nand_probe(struct platform_device *pdev)
+{
+ struct pxa3xx_nand_platform_data *pdata;
+ struct pxa3xx_nand_info *info;
+ struct nand_chip *this;
+ struct mtd_info *mtd;
+ struct resource *r;
+ int ret = 0, irq;
+
+ pdata = pdev->dev.platform_data;
+
+ if (pdata == NULL) {
+ dev_err(&pdev->dev, "no platform data defined\n");
+ return -ENODEV;
+ }
+
+ mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct pxa3xx_nand_info),
+ GFP_KERNEL);
+ if (mtd == NULL) {
+ dev_err(&pdev->dev, "failed to allocate memory\n");
+ return -ENOMEM;
+ }
+
+ info = (struct pxa3xx_nand_info *)(&mtd[1]);
+ info->pdev = pdev;
+
+ this = &info->nand_chip;
+ mtd->priv = info;
+
+ info->clk = clk_get(&pdev->dev, "NANDCLK");
+ if (IS_ERR(info->clk)) {
+ dev_err(&pdev->dev, "failed to get nand clock\n");
+ ret = PTR_ERR(info->clk);
+ goto fail_free_mtd;
+ }
+ clk_enable(info->clk);
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "no resource defined for data DMA\n");
+ ret = -ENXIO;
+ goto fail_put_clk;
+ }
+ info->drcmr_dat = r->start;
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "no resource defined for command DMA\n");
+ ret = -ENXIO;
+ goto fail_put_clk;
+ }
+ info->drcmr_cmd = r->start;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no IRQ resource defined\n");
+ ret = -ENXIO;
+ goto fail_put_clk;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "no IO memory resource defined\n");
+ ret = -ENODEV;
+ goto fail_put_clk;
+ }
+
+ r = request_mem_region(r->start, r->end - r->start + 1, pdev->name);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "failed to request memory resource\n");
+ ret = -EBUSY;
+ goto fail_put_clk;
+ }
+
+ info->mmio_base = ioremap(r->start, r->end - r->start + 1);
+ if (info->mmio_base == NULL) {
+ dev_err(&pdev->dev, "ioremap() failed\n");
+ ret = -ENODEV;
+ goto fail_free_res;
+ }
+
+ ret = pxa3xx_nand_init_buff(info);
+ if (ret)
+ goto fail_free_io;
+
+ ret = request_irq(IRQ_NAND, pxa3xx_nand_irq, IRQF_DISABLED,
+ pdev->name, info);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to request IRQ\n");
+ goto fail_free_buf;
+ }
+
+ ret = pxa3xx_nand_detect_flash(info);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to detect flash\n");
+ ret = -ENODEV;
+ goto fail_free_irq;
+ }
+
+ pxa3xx_nand_init_mtd(mtd, info);
+
+ platform_set_drvdata(pdev, mtd);
+
+ if (nand_scan(mtd, 1)) {
+ dev_err(&pdev->dev, "failed to scan nand\n");
+ ret = -ENXIO;
+ goto fail_free_irq;
+ }
+
+ return add_mtd_partitions(mtd, pdata->parts, pdata->nr_parts);
+
+fail_free_irq:
+ free_irq(IRQ_NAND, info);
+fail_free_buf:
+ if (use_dma) {
+ pxa_free_dma(info->data_dma_ch);
+ dma_free_coherent(&pdev->dev, info->data_buff_size,
+ info->data_buff, info->data_buff_phys);
+ } else
+ kfree(info->data_buff);
+fail_free_io:
+ iounmap(info->mmio_base);
+fail_free_res:
+ release_mem_region(r->start, r->end - r->start + 1);
+fail_put_clk:
+ clk_disable(info->clk);
+ clk_put(info->clk);
+fail_free_mtd:
+ kfree(mtd);
+ return ret;
+}
+
+static int pxa3xx_nand_remove(struct platform_device *pdev)
+{
+ struct mtd_info *mtd = platform_get_drvdata(pdev);
+ struct pxa3xx_nand_info *info = mtd->priv;
+
+ platform_set_drvdata(pdev, NULL);
+
+ del_mtd_device(mtd);
+ del_mtd_partitions(mtd);
+ free_irq(IRQ_NAND, info);
+ if (use_dma) {
+ pxa_free_dma(info->data_dma_ch);
+ dma_free_writecombine(&pdev->dev, info->data_buff_size,
+ info->data_buff, info->data_buff_phys);
+ } else
+ kfree(info->data_buff);
+ kfree(mtd);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev);
+ struct pxa3xx_nand_info *info = mtd->priv;
+
+ if (info->state != STATE_READY) {
+ dev_err(&pdev->dev, "driver busy, state = %d\n", info->state);
+ return -EAGAIN;
+ }
+
+ return 0;
+}
+
+static int pxa3xx_nand_resume(struct platform_device *pdev)
+{
+ struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev);
+ struct pxa3xx_nand_info *info = mtd->priv;
+
+ clk_enable(info->clk);
+
+ return pxa3xx_nand_config_flash(info);
+}
+#else
+#define pxa3xx_nand_suspend NULL
+#define pxa3xx_nand_resume NULL
+#endif
+
+static struct platform_driver pxa3xx_nand_driver = {
+ .driver = {
+ .name = "pxa3xx-nand",
+ },
+ .probe = pxa3xx_nand_probe,
+ .remove = pxa3xx_nand_remove,
+ .suspend = pxa3xx_nand_suspend,
+ .resume = pxa3xx_nand_resume,
+};
+
+static int __init pxa3xx_nand_init(void)
+{
+ return platform_driver_register(&pxa3xx_nand_driver);
+}
+module_init(pxa3xx_nand_init);
+
+static void __exit pxa3xx_nand_exit(void)
+{
+ platform_driver_unregister(&pxa3xx_nand_driver);
+}
+module_exit(pxa3xx_nand_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("PXA3xx NAND controller driver");
projects / GitHub / mt8127 / android_kernel_alcatel_ttab.git / commitdiff