+++ /dev/null
-Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device
-
-Required properties:
- - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt.
- - active-semi,chglev-gpios: charge current level phandle with args
- as described in ../gpio/gpio.txt.
-
-Optional properties:
- - active-semi,check-battery-temperature: boolean to check the battery
- temperature or not.
- - active-semi,input-voltage-threshold-microvolt: unit: mV;
- Specifies the charger's input over-voltage threshold value;
- The value can be: 6600, 7000, 7500, 8000; default: 6600
- - active-semi,precondition-timeout: unit: minutes;
- Specifies the charger's PRECONDITION safety timer setting value;
- The value can be: 40, 60, 80, 0; If 0, it means to disable this timer;
- default: 40.
- - active-semi,total-timeout: unit: hours;
- Specifies the charger's total safety timer setting value;
- The value can be: 3, 4, 5, 0; If 0, it means to disable this timer;
- default: 3.
-
-Example:
- pmic@5b {
- compatible = "active-semi,act8945a";
- reg = <0x5b>;
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_charger_chglev>;
- active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
- active-semi,input-voltage-threshold-microvolt = <6600>;
- active-semi,precondition-timeout = <40>;
- active-semi,total-timeout = <3>;
- };
+++ /dev/null
-Binding for TI bq2415x Li-Ion Charger
-
-Required properties:
-- compatible: Should contain one of the following:
- * "ti,bq24150"
- * "ti,bq24150"
- * "ti,bq24150a"
- * "ti,bq24151"
- * "ti,bq24151a"
- * "ti,bq24152"
- * "ti,bq24153"
- * "ti,bq24153a"
- * "ti,bq24155"
- * "ti,bq24156"
- * "ti,bq24156a"
- * "ti,bq24158"
-- reg: integer, i2c address of the device.
-- ti,current-limit: integer, initial maximum current charger can pull
- from power supply in mA.
-- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
- The chip will use slow precharge if battery voltage
- is below this value.
-- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
-- ti,charge-current: integer, maximum charging current in mA.
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in mA).
-- ti,resistor-sense: integer, value of sensing resistor in milliohm.
-
-Optional properties:
-- ti,usb-charger-detection: phandle to usb charger detection device.
- (required for auto mode)
-
-Example from Nokia N900:
-
-bq24150a {
- compatible = "ti,bq24150a";
- reg = <0x6b>;
-
- ti,current-limit = <100>;
- ti,weak-battery-voltage = <3400>;
- ti,battery-regulation-voltage = <4200>;
- ti,charge-current = <650>;
- ti,termination-current = <100>;
- ti,resistor-sense = <68>;
-
- ti,usb-charger-detection = <&isp1704>;
-};
+++ /dev/null
-Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
-
-Required properties:
-- compatible: Should contain one of the following:
- * "ti,bq24250"
- * "ti,bq24251"
- * "ti,bq24257"
-- reg: integer, i2c address of the device.
-- interrupt-parent: Should be the phandle for the interrupt controller. Use in
- conjunction with "interrupts".
-- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
- conjunction with "interrupt-parent".
-- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
-- ti,charge-current: integer, maximum charging current in uA.
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA).
-
-Optional properties:
-- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
- This pin is not available on all devices however it should be used if
- possible as this is the recommended way to obtain the charger's input PG
- state. If this pin is not specified a software-based approach for PG
- detection is used.
-- ti,current-limit: The maximum current to be drawn from the charger's input
- (in uA). If this property is not specified, the input limit current is
- set automatically using USB D+/D- signal based charger type detection.
- If the hardware does not support the D+/D- based detection, a default
- of 500,000 is used (=500mA) instead.
-- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
- not specified a default of 6,5000,000 (=6.5V) is used.
-- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
- power path management (in uV). If not specified a default of 4,360,000
- (=4.36V) is used.
-
-Example:
-
-bq24257 {
- compatible = "ti,bq24257";
- reg = <0x6a>;
- interrupt-parent = <&gpio1>;
- interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
-
- pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <1000000>;
- ti,termination-current = <50000>;
-};
-
-Example:
-
-bq24250 {
- compatible = "ti,bq24250";
- reg = <0x6a>;
- interrupt-parent = <&gpio1>;
- interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <500000>;
- ti,termination-current = <50000>;
- ti,current-limit = <900000>;
- ti,ovp-voltage = <9500000>;
- ti,in-dpm-voltage = <4440000>;
-};
+++ /dev/null
-Binding for TI bq25890 Li-Ion Charger
-
-Required properties:
-- compatible: Should contain one of the following:
- * "ti,bq25890"
-- reg: integer, i2c address of the device.
-- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
-- ti,charge-current: integer, maximum charging current (in uA);
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA);
-- ti,precharge-current: integer, maximum charge current during precharge
- phase (in uA);
-- ti,minimum-sys-voltage: integer, when battery is charging and it is below
- minimum system voltage, the system will be regulated above
- minimum-sys-voltage setting (in uV);
-- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
-- ti,boost-max-current: integer, maximum allowed current draw in boost mode
- (in uA).
-
-Optional properties:
-- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
- otherwise 1.5MHz;
-- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
- input current will be the lower between the resistor setting and the IINLIM
- register setting;
-- ti,thermal-regulation-threshold: integer, temperature above which the charge
- current is lowered, to avoid overheating (in degrees Celsius). If omitted,
- the default setting will be used (120 degrees);
-
-Example:
-
-bq25890 {
- compatible = "ti,bq25890";
- reg = <0x6a>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <1000000>;
- ti,termination-current = <50000>;
- ti,precharge-current = <128000>;
- ti,minimum-sys-voltage = <3600000>;
- ti,boost-voltage = <5000000>;
- ti,boost-max-current = <1000000>;
-
- ti,use-ilim-pin;
- ti,thermal-regulation-threshold = <120>;
-};
+++ /dev/null
-Dialog Semiconductor DA9150 Charger Power Supply bindings
-
-Required properties:
-- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply
-
-Optional properties:
-- io-channels: List of phandle and IIO specifier pairs
-- io-channel-names: List of channel names used by charger
- ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"]
- (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info)
-
-
-Example:
-
- da9150-charger {
- compatible = "dlg,da9150-charger";
-
- io-channels = <&gpadc 0>,
- <&gpadc 2>,
- <&gpadc 8>,
- <&gpadc 5>;
- io-channel-names = "CHAN_IBUS",
- "CHAN_VBUS",
- "CHAN_TJUNC",
- "CHAN_VBAT";
- };
+++ /dev/null
-Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings
-
-Required properties:
-- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply
-
-Optional properties:
-- dlg,update-interval: Interval time (milliseconds) between battery level checks.
-- dlg,warn-soc-level: Battery discharge level (%) where warning event raised.
- [1 - 100]
-- dlg,crit-soc-level: Battery discharge level (%) where critical event raised.
- This value should be lower than the warning level.
- [1 - 100]
-
-
-Example:
-
- fuel-gauge {
- compatible = "dlg,da9150-fuel-gauge";
-
- dlg,update-interval = <10000>;
- dlg,warn-soc-level = /bits/ 8 <15>;
- dlg,crit-soc-level = /bits/ 8 <5>;
- };
+++ /dev/null
-Binding for NXP ISP1704 USB Charger Detection
-
-Required properties:
-- compatible: Should contain one of the following:
- * "nxp,isp1704"
-- nxp,enable-gpio: Should contain a phandle + gpio-specifier
- to the GPIO pin connected to the chip's enable pin.
-- usb-phy: Should contain a phandle to the USB PHY
- the ISP1704 is connected to.
-
-Example:
-
-isp1704 {
- compatible = "nxp,isp1704";
- nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
- usb-phy = <&usb2_phy>;
-};
+++ /dev/null
-binding for LTC2941 and LTC2943 battery gauges
-
-Both the LTC2941 and LTC2943 measure battery capacity.
-The LTC2943 is compatible with the LTC2941, it adds voltage and
-temperature monitoring, and uses a slightly different conversion
-formula for the charge counter.
-
-Required properties:
-- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the
- type of I2C chip attached.
-- reg: The 7-bit I2C address.
-- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit
- negative value when the battery has been connected to the wrong end of the
- resistor.
-- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet.
- This determines the range and accuracy of the gauge. The value is programmed
- into the chip only if it differs from the current setting. The setting is
- lost when the battery is disconnected.
-
-Example from the Topic Miami Florida board:
-
- fuelgauge: ltc2943@64 {
- compatible = "ltc2943";
- reg = <0x64>;
- lltc,resistor-sense = <15>;
- lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */
- };
+++ /dev/null
-Qualcomm Coincell Charger:
-
-The hardware block controls charging for a coincell or capacitor that is
-used to provide power backup for certain features of the power management
-IC (PMIC)
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be: "qcom,pm8941-coincell"
-
-- reg:
- Usage: required
- Value type: <u32>
- Definition: base address of the coincell charger registers
-
-- qcom,rset-ohms:
- Usage: required
- Value type: <u32>
- Definition: resistance (in ohms) for current-limiting resistor
- must be one of: 800, 1200, 1700, 2100
-
-- qcom,vset-millivolts:
- Usage: required
- Value type: <u32>
- Definition: voltage (in millivolts) to apply for charging
- must be one of: 2500, 3000, 3100, 3200
-
-- qcom,charger-disable:
- Usage: optional
- Value type: <boolean>
- Definition: defining this property disables charging
-
-This charger is a sub-node of one of the 8941 PMIC blocks, and is specified
-as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and
-../mfd/qcom-pm8xxx.txt
-
-Example:
-
- pm8941@0 {
- coincell@2800 {
- compatible = "qcom,pm8941-coincell";
- reg = <0x2800>;
-
- qcom,rset-ohms = <2100>;
- qcom,vset-millivolts = <3000>;
- };
- };
--- /dev/null
+Axxia Restart Driver
+
+This driver can do reset of the Axxia SoC. It uses the registers in the syscon
+block to initiate a chip reset.
+
+Required Properties:
+ -compatible: "lsi,axm55xx-reset"
+ -syscon: phandle to the syscon node.
+
+Example:
+
+ syscon: syscon@2010030000 {
+ compatible = "lsi,axxia-syscon", "syscon";
+ reg = <0x20 0x10030000 0 0x2000>;
+ };
+
+ reset: reset@2010031000 {
+ compatible = "lsi,axm55xx-reset";
+ syscon = <&syscon>;
+ };
--- /dev/null
+i.mx6 Poweroff Driver
+
+SNVS_LPCR in SNVS module can power off the whole system by pull
+PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC.
+If you don't want to use PMIC_ON_REQ as power on/off control,
+please set status='disabled' to disable this driver.
+
+Required Properties:
+-compatible: "fsl,sec-v4.0-poweroff"
+-reg: Specifies the physical address of the SNVS_LPCR register
+
+Example:
+ snvs@020cc000 {
+ compatible = "fsl,sec-v4.0-mon", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x020cc000 0x4000>;
+ .....
+ snvs_poweroff: snvs-poweroff@38 {
+ compatible = "fsl,sec-v4.0-poweroff";
+ reg = <0x38 0x4>;
+ };
+ }
--- /dev/null
+MSM Restart Driver
+
+A power supply hold (ps-hold) bit is set to power the msm chipsets.
+Clearing that bit allows us to restart/poweroff. The difference
+between poweroff and restart is determined by unique power manager IC
+settings.
+
+Required Properties:
+-compatible: "qcom,pshold"
+-reg: Specifies the physical address of the ps-hold register
+
+Example:
+
+ restart@fc4ab000 {
+ compatible = "qcom,pshold";
+ reg = <0xfc4ab000 0x4>;
+ };
--- /dev/null
+* QNAP Power Off
+
+QNAP NAS devices have a microcontroller controlling the main power
+supply. This microcontroller is connected to UART1 of the Kirkwood and
+Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the
+microcontroller to turn the power off. This driver adds a handler to
+pm_power_off which is called to turn the power off.
+
+Synology NAS devices use a similar scheme, but a different baud rate,
+9600, and a different character, '1'.
+
+Required Properties:
+- compatible: Should be "qnap,power-off" or "synology,power-off"
+
+- reg: Address and length of the register set for UART1
+- clocks: tclk clock
--- /dev/null
+* Restart Power Off
+
+Buffalo Linkstation LS-XHL and LS-CHLv2, and other devices power off
+by restarting and letting u-boot keep hold of the machine until the
+user presses a button.
+
+Required Properties:
+- compatible: Should be "restart-poweroff"
+++ /dev/null
-Binding for Richtek rt9455 battery charger
-
-Required properties:
-- compatible: it should contain one of the following:
- "richtek,rt9455".
-- reg: integer, i2c address of the device.
-- interrupt-parent: the phandle for the interrupt controller that
- services interrupts for this device.
-- interrupts: interrupt mapping for GPIO IRQ, it should be
- configured with IRQ_TYPE_LEVEL_LOW flag.
-- richtek,output-charge-current: integer, output current from the charger to the
- battery, in uA.
-- richtek,end-of-charge-percentage: integer, percent of the output charge current.
- When the current in constant-voltage phase drops
- below output_charge_current x end-of-charge-percentage,
- charge is terminated.
-- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV.
-- richtek,boost-output-voltage: integer, maximum voltage provided to consumer
- devices, when the charger is in boost mode, in uV.
-
-Optional properties:
-- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to
- decrease voltage level when the over current
- of the input power source occurs.
- This prevents input voltage drop due to insufficient
- current provided by the power source.
- Default: 4500000 uV (4.5V)
-- richtek,avg-input-current-regulation: integer, input current value in uA drained by the
- charger from the power source.
- Default: 500000 uA (500mA)
-
-Example:
-
-rt9455@22 {
- compatible = "richtek,rt9455";
- reg = <0x22>;
-
- interrupt-parent = <&gpio1>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- richtek,output-charge-current = <500000>;
- richtek,end-of-charge-percentage = <10>;
- richtek,battery-regulation-voltage = <4200000>;
- richtek,boost-output-voltage = <5050000>;
-
- richtek,min-input-voltage-regulation = <4500000>;
- richtek,avg-input-current-regulation = <500000>;
-};
+++ /dev/null
-Binding for Nokia N900 battery
-
-The Nokia N900 battery status can be read via the TWL4030's A/D converter.
-
-Required properties:
-- compatible: Should contain one of the following:
- * "nokia,n900-battery"
-- io-channels: Should contain IIO channel specifiers
- for each element in io-channel-names.
-- io-channel-names: Should contain the following values:
- * "temp" - The ADC channel for temperature reading
- * "bsi" - The ADC channel for battery size identification
- * "vbat" - The ADC channel to measure the battery voltage
-
-Example from Nokia N900:
-
-battery: n900-battery {
- compatible = "nokia,n900-battery";
- io-channels = <&twl4030_madc 0>,
- <&twl4030_madc 4>,
- <&twl4030_madc 12>;
- io-channel-names = "temp",
- "bsi",
- "vbat";
-};
--- /dev/null
+=== AB8500 Battery Temperature Monitor Driver ===
+
+The properties below describes the node for btemp driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-btemp"
+- battery = Shall be battery specific information
+
+ Example:
+ ab8500_btemp {
+ compatible = "stericsson,ab8500-btemp";
+ battery = <&ab8500_battery>;
+ };
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
--- /dev/null
+=== AB8500 Charging Algorithm Driver ===
+
+The properties below describes the node for chargalg driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-chargalg"
+- battery = Shall be battery specific information
+
+Example:
+ab8500_chargalg {
+ compatible = "stericsson,ab8500-chargalg";
+ battery = <&ab8500_battery>;
+};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
--- /dev/null
+=== AB8500 Charger Driver ===
+
+Required Properties:
+- compatible = Shall be "stericsson,ab8500-charger"
+- battery = Shall be battery specific information
+ Example:
+ ab8500_charger {
+ compatible = "stericsson,ab8500-charger";
+ battery = <&ab8500_battery>;
+ };
+
+- vddadc-supply: Supply for USB and Main charger
+ Example:
+ ab8500-charger {
+ vddadc-supply = <&ab8500_ldo_tvout_reg>;
+ }
+- autopower_cfg:
+ Boolean value depicting the presence of 'automatic poweron after powerloss'
+ Example:
+ ab8500-charger {
+ autopower_cfg;
+ };
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
--- /dev/null
+=== AB8500 Fuel Gauge Driver ===
+
+AB8500 is a mixed signal multimedia and power management
+device comprising: power and energy-management-module,
+wall-charger, usb-charger, audio codec, general purpose adc,
+tvout, clock management and sim card interface.
+
+Fuelgauge support is part of energy-management-modules, other
+components of this module are:
+main-charger, usb-combo-charger and battery-temperature-monitoring.
+
+The properties below describes the node for fuelgauge driver.
+
+Required Properties:
+- compatible = This shall be: "stericsson,ab8500-fg"
+- battery = Shall be battery specific information
+ Example:
+ ab8500_fg {
+ compatible = "stericsson,ab8500-fg";
+ battery = <&ab8500_battery>;
+ };
+
+dependent node:
+ ab8500_battery: ab8500_battery {
+ };
+ This node will provide information on 'thermistor interface' and
+ 'battery technology type' used.
+
+Properties of this node are:
+thermistor-on-batctrl:
+ A boolean value indicating thermistor interface to battery
+
+ Note:
+ 'btemp' and 'batctrl' are the pins interfaced for battery temperature
+ measurement, 'btemp' signal is used when NTC(negative temperature
+ coefficient) resister is interfaced external to battery whereas
+ 'batctrl' pin is used when NTC resister is internal to battery.
+
+ Example:
+ ab8500_battery: ab8500_battery {
+ thermistor-on-batctrl;
+ };
+ indicates: NTC resister is internal to battery, 'batctrl' is used
+ for thermal measurement.
+
+ The absence of property 'thermal-on-batctrl' indicates
+ NTC resister is external to battery and 'btemp' signal is used
+ for thermal measurement.
+
+battery-type:
+ This shall be the battery manufacturing technology type,
+ allowed types are:
+ "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn"
+ Example:
+ ab8500_battery: ab8500_battery {
+ stericsson,battery-type = "LIPO";
+ }
+
--- /dev/null
+Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device
+
+Required properties:
+ - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt.
+ - active-semi,chglev-gpios: charge current level phandle with args
+ as described in ../gpio/gpio.txt.
+
+Optional properties:
+ - active-semi,check-battery-temperature: boolean to check the battery
+ temperature or not.
+ - active-semi,input-voltage-threshold-microvolt: unit: mV;
+ Specifies the charger's input over-voltage threshold value;
+ The value can be: 6600, 7000, 7500, 8000; default: 6600
+ - active-semi,precondition-timeout: unit: minutes;
+ Specifies the charger's PRECONDITION safety timer setting value;
+ The value can be: 40, 60, 80, 0; If 0, it means to disable this timer;
+ default: 40.
+ - active-semi,total-timeout: unit: hours;
+ Specifies the charger's total safety timer setting value;
+ The value can be: 3, 4, 5, 0; If 0, it means to disable this timer;
+ default: 3.
+
+Example:
+ pmic@5b {
+ compatible = "active-semi,act8945a";
+ reg = <0x5b>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_charger_chglev>;
+ active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
+ active-semi,input-voltage-threshold-microvolt = <6600>;
+ active-semi,precondition-timeout = <40>;
+ active-semi,total-timeout = <3>;
+ };
--- /dev/null
+AXP20x USB power supply
+
+Required Properties:
+-compatible: One of: "x-powers,axp202-usb-power-supply"
+ "x-powers,axp221-usb-power-supply"
+
+This node is a subnode of the axp20x PMIC.
+
+Example:
+
+axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ regulators {
+ x-powers,dcdc-freq = <1500>;
+
+ vdd_cpu: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ ...
+ };
+
+ usb-power-supply: usb-power-supply {
+ compatible = "x-powers,axp202-usb-power-supply";
+ };
+};
--- /dev/null
+Binding for TI bq2415x Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24150"
+ * "ti,bq24150"
+ * "ti,bq24150a"
+ * "ti,bq24151"
+ * "ti,bq24151a"
+ * "ti,bq24152"
+ * "ti,bq24153"
+ * "ti,bq24153a"
+ * "ti,bq24155"
+ * "ti,bq24156"
+ * "ti,bq24156a"
+ * "ti,bq24158"
+- reg: integer, i2c address of the device.
+- ti,current-limit: integer, initial maximum current charger can pull
+ from power supply in mA.
+- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
+ The chip will use slow precharge if battery voltage
+ is below this value.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
+- ti,charge-current: integer, maximum charging current in mA.
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in mA).
+- ti,resistor-sense: integer, value of sensing resistor in milliohm.
+
+Optional properties:
+- ti,usb-charger-detection: phandle to usb charger detection device.
+ (required for auto mode)
+
+Example from Nokia N900:
+
+bq24150a {
+ compatible = "ti,bq24150a";
+ reg = <0x6b>;
+
+ ti,current-limit = <100>;
+ ti,weak-battery-voltage = <3400>;
+ ti,battery-regulation-voltage = <4200>;
+ ti,charge-current = <650>;
+ ti,termination-current = <100>;
+ ti,resistor-sense = <68>;
+
+ ti,usb-charger-detection = <&isp1704>;
+};
--- /dev/null
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
+ * "ti,bq24257"
+- reg: integer, i2c address of the device.
+- interrupt-parent: Should be the phandle for the interrupt controller. Use in
+ conjunction with "interrupts".
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+ conjunction with "interrupt-parent".
+- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+ This pin is not available on all devices however it should be used if
+ possible as this is the recommended way to obtain the charger's input PG
+ state. If this pin is not specified a software-based approach for PG
+ detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+ (in uA). If this property is not specified, the input limit current is
+ set automatically using USB D+/D- signal based charger type detection.
+ If the hardware does not support the D+/D- based detection, a default
+ of 500,000 is used (=500mA) instead.
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+ not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+ power path management (in uV). If not specified a default of 4,360,000
+ (=4.36V) is used.
+
+Example:
+
+bq24257 {
+ compatible = "ti,bq24257";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <1000000>;
+ ti,termination-current = <50000>;
+};
+
+Example:
+
+bq24250 {
+ compatible = "ti,bq24250";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <500000>;
+ ti,termination-current = <50000>;
+ ti,current-limit = <900000>;
+ ti,ovp-voltage = <9500000>;
+ ti,in-dpm-voltage = <4440000>;
+};
--- /dev/null
+Binding for TI bq25890 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq25890"
+- reg: integer, i2c address of the device.
+- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
+- ti,charge-current: integer, maximum charging current (in uA);
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in uA);
+- ti,precharge-current: integer, maximum charge current during precharge
+ phase (in uA);
+- ti,minimum-sys-voltage: integer, when battery is charging and it is below
+ minimum system voltage, the system will be regulated above
+ minimum-sys-voltage setting (in uV);
+- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
+- ti,boost-max-current: integer, maximum allowed current draw in boost mode
+ (in uA).
+
+Optional properties:
+- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
+ otherwise 1.5MHz;
+- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
+ input current will be the lower between the resistor setting and the IINLIM
+ register setting;
+- ti,thermal-regulation-threshold: integer, temperature above which the charge
+ current is lowered, to avoid overheating (in degrees Celsius). If omitted,
+ the default setting will be used (120 degrees);
+
+Example:
+
+bq25890 {
+ compatible = "ti,bq25890";
+ reg = <0x6a>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <1000000>;
+ ti,termination-current = <50000>;
+ ti,precharge-current = <128000>;
+ ti,minimum-sys-voltage = <3600000>;
+ ti,boost-voltage = <5000000>;
+ ti,boost-max-current = <1000000>;
+
+ ti,use-ilim-pin;
+ ti,thermal-regulation-threshold = <120>;
+};
--- /dev/null
+charger-manager bindings
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties :
+ - compatible : "charger-manager"
+ - <>-supply : for regulator consumer
+ - cm-num-chargers : number of chargers
+ - cm-chargers : name of chargers
+ - cm-fuel-gauge : name of battery fuel gauge
+ - subnode <regulator> :
+ - cm-regulator-name : name of charger regulator
+ - subnode <cable> :
+ - cm-cable-name : name of charger cable
+ - cm-cable-extcon : name of extcon dev
+(optional) - cm-cable-min : minimum current of cable
+(optional) - cm-cable-max : maximum current of cable
+
+Optional properties :
+ - cm-name : charger manager's name (default : "battery")
+ - cm-poll-mode : polling mode (enum polling_modes)
+ - cm-poll-interval : polling interval
+ - cm-battery-stat : battery status (enum data_source)
+ - cm-fullbatt-* : data for full battery checking
+ - cm-thermal-zone : name of external thermometer's thermal zone
+ - cm-battery-* : threshold battery temperature for charging
+ -cold : critical cold temperature of battery for charging
+ -cold-in-minus : flag that cold temperature is in minus degrees
+ -hot : critical hot temperature of battery for charging
+ -temp-diff : temperature difference to allow recharging
+ - cm-dis/charging-max = limits of charging duration
+
+Example :
+ charger-manager@0 {
+ compatible = "charger-manager";
+ chg-reg-supply = <&charger_regulator>;
+
+ cm-name = "battery";
+ /* Always polling ON : 30s */
+ cm-poll-mode = <1>;
+ cm-poll-interval = <30000>;
+
+ cm-fullbatt-vchkdrop-ms = <30000>;
+ cm-fullbatt-vchkdrop-volt = <150000>;
+ cm-fullbatt-soc = <100>;
+
+ cm-battery-stat = <3>;
+
+ cm-num-chargers = <3>;
+ cm-chargers = "charger0", "charger1", "charger2";
+
+ cm-fuel-gauge = "fuelgauge0";
+
+ cm-thermal-zone = "thermal_zone.1"
+ /* in deci centigrade */
+ cm-battery-cold = <50>;
+ cm-battery-cold-in-minus;
+ cm-battery-hot = <800>;
+ cm-battery-temp-diff = <100>;
+
+ /* Allow charging for 5hr */
+ cm-charging-max = <18000000>;
+ /* Allow discharging for 2hr */
+ cm-discharging-max = <7200000>;
+
+ regulator@0 {
+ cm-regulator-name = "chg-reg";
+ cable@0 {
+ cm-cable-name = "USB";
+ cm-cable-extcon = "extcon-dev.0";
+ cm-cable-min = <475000>;
+ cm-cable-max = <500000>;
+ };
+ cable@1 {
+ cm-cable-name = "TA";
+ cm-cable-extcon = "extcon-dev.0";
+ cm-cable-min = <650000>;
+ cm-cable-max = <675000>;
+ };
+ };
+
+ };
--- /dev/null
+Dialog Semiconductor DA9150 Charger Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply
+
+Optional properties:
+- io-channels: List of phandle and IIO specifier pairs
+- io-channel-names: List of channel names used by charger
+ ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"]
+ (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info)
+
+
+Example:
+
+ da9150-charger {
+ compatible = "dlg,da9150-charger";
+
+ io-channels = <&gpadc 0>,
+ <&gpadc 2>,
+ <&gpadc 8>,
+ <&gpadc 5>;
+ io-channel-names = "CHAN_IBUS",
+ "CHAN_VBUS",
+ "CHAN_TJUNC",
+ "CHAN_VBAT";
+ };
--- /dev/null
+Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply
+
+Optional properties:
+- dlg,update-interval: Interval time (milliseconds) between battery level checks.
+- dlg,warn-soc-level: Battery discharge level (%) where warning event raised.
+ [1 - 100]
+- dlg,crit-soc-level: Battery discharge level (%) where critical event raised.
+ This value should be lower than the warning level.
+ [1 - 100]
+
+
+Example:
+
+ fuel-gauge {
+ compatible = "dlg,da9150-fuel-gauge";
+
+ dlg,update-interval = <10000>;
+ dlg,warn-soc-level = /bits/ 8 <15>;
+ dlg,crit-soc-level = /bits/ 8 <5>;
+ };
--- /dev/null
+gpio-charger
+
+Required properties :
+ - compatible : "gpio-charger"
+ - gpios : GPIO indicating the charger presence.
+ See GPIO binding in bindings/gpio/gpio.txt .
+ - charger-type : power supply type, one of
+ unknown
+ battery
+ ups
+ mains
+ usb-sdp (USB standard downstream port)
+ usb-dcp (USB dedicated charging port)
+ usb-cdp (USB charging downstream port)
+ usb-aca (USB accessory charger adapter)
+
+Example:
+
+ usb_charger: charger {
+ compatible = "gpio-charger";
+ charger-type = "usb-sdp";
+ gpios = <&gpf0 2 0 0 0>;
+ }
+
+ battery {
+ power-supplies = <&usb_charger>;
+ };
--- /dev/null
+Binding for NXP ISP1704 USB Charger Detection
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nxp,isp1704"
+- nxp,enable-gpio: Should contain a phandle + gpio-specifier
+ to the GPIO pin connected to the chip's enable pin.
+- usb-phy: Should contain a phandle to the USB PHY
+ the ISP1704 is connected to.
+
+Example:
+
+isp1704 {
+ compatible = "nxp,isp1704";
+ nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+ usb-phy = <&usb2_phy>;
+};
--- /dev/null
+Binding for TI/National Semiconductor LP8727 Charger
+
+Required properties:
+- compatible: "ti,lp8727"
+- reg: I2C slave address 27h
+
+Optional properties:
+- interrupt-parent: interrupt controller node (see interrupt binding[0])
+- interrupts: interrupt specifier (see interrupt binding[0])
+- debounce-ms: interrupt debounce time. (u32)
+
+AC and USB charging parameters
+- charger-type: "ac" or "usb" (string)
+- eoc-level: value of 'enum lp8727_eoc_level' (u8)
+- charging-current: value of 'enum lp8727_ichg' (u8)
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example)
+
+lp8727@27 {
+ compatible = "ti,lp8727";
+ reg = <0x27>;
+
+ /* GPIO 134 is used for LP8728 interrupt pin */
+ interrupt-parent = <&gpio5>; /* base = 128 */
+ interrupts = <6 0x2>; /* offset = 6, falling edge type */
+
+ debounce-ms = <300>;
+
+ /* AC charger: 5% EOC and 500mA charging current */
+ ac {
+ charger-type = "ac";
+ eoc-level = /bits/ 8 <0>;
+ charging-current = /bits/ 8 <4>;
+ };
+
+ /* USB charger: 10% EOC and 400mA charging current */
+ usb {
+ charger-type = "usb";
+ eoc-level = /bits/ 8 <1>;
+ charging-current = /bits/ 8 <2>;
+ };
+};
--- /dev/null
+binding for LTC2941 and LTC2943 battery gauges
+
+Both the LTC2941 and LTC2943 measure battery capacity.
+The LTC2943 is compatible with the LTC2941, it adds voltage and
+temperature monitoring, and uses a slightly different conversion
+formula for the charge counter.
+
+Required properties:
+- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the
+ type of I2C chip attached.
+- reg: The 7-bit I2C address.
+- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit
+ negative value when the battery has been connected to the wrong end of the
+ resistor.
+- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet.
+ This determines the range and accuracy of the gauge. The value is programmed
+ into the chip only if it differs from the current setting. The setting is
+ lost when the battery is disconnected.
+
+Example from the Topic Miami Florida board:
+
+ fuelgauge: ltc2943@64 {
+ compatible = "ltc2943";
+ reg = <0x64>;
+ lltc,resistor-sense = <15>;
+ lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */
+ };
--- /dev/null
+max17042_battery
+~~~~~~~~~~~~~~~~
+
+Required properties :
+ - compatible : "maxim,max17042"
+
+Optional properties :
+ - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms
+ (datasheet-recommended value is 10000).
+ Defining this property enables current-sense functionality.
+
+Optional threshold properties :
+ If skipped the condition won't be reported.
+ - maxim,cold-temp : Temperature threshold to report battery
+ as cold (in tenths of degree Celsius).
+ - maxim,over-heat-temp : Temperature threshold to report battery
+ as over heated (in tenths of degree Celsius).
+ - maxim,dead-volt : Voltage threshold to report battery
+ as dead (in mV).
+ - maxim,over-volt : Voltage threshold to report battery
+ as over voltage (in mV).
+
+Example:
+
+ battery-charger@36 {
+ compatible = "maxim,max17042";
+ reg = <0x36>;
+ maxim,rsns-microohm = <10000>;
+ maxim,over-heat-temp = <600>;
+ maxim,over-volt = <4300>;
+ };
--- /dev/null
+max8925-battery bindings
+~~~~~~~~~~~~~~~~
+
+Optional properties :
+ - batt-detect: whether support battery detect
+ - topoff-threshold: set charging current in topoff mode
+ - fast-charge: set charging current in fast mode
+ - no-temp-support: whether support temperature protection detect
+ - no-insert-detect: whether support insert detect
+
+Example:
+ charger {
+ batt-detect = <0>;
+ topoff-threshold = <1>;
+ fast-charge = <7>;
+ no-temp-support = <0>;
+ no-insert-detect = <0>;
+ };
--- /dev/null
+OLPC battery
+~~~~~~~~~~~~
+
+Required properties:
+ - compatible : "olpc,xo1-battery"
--- /dev/null
+Power Supply Core Support
+
+Optional Properties:
+ - power-supplies : This property is added to a supply in order to list the
+ devices which supply it power, referenced by their phandles.
+
+Example:
+
+ usb-charger: power@e {
+ compatible = "some,usb-charger";
+ ...
+ };
+
+ ac-charger: power@c {
+ compatible = "some,ac-charger";
+ ...
+ };
+
+ battery@b {
+ compatible = "some,battery";
+ ...
+ power-supplies = <&usb-charger>, <&ac-charger>;
+ };
--- /dev/null
+Qualcomm Coincell Charger:
+
+The hardware block controls charging for a coincell or capacitor that is
+used to provide power backup for certain features of the power management
+IC (PMIC)
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be: "qcom,pm8941-coincell"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: base address of the coincell charger registers
+
+- qcom,rset-ohms:
+ Usage: required
+ Value type: <u32>
+ Definition: resistance (in ohms) for current-limiting resistor
+ must be one of: 800, 1200, 1700, 2100
+
+- qcom,vset-millivolts:
+ Usage: required
+ Value type: <u32>
+ Definition: voltage (in millivolts) to apply for charging
+ must be one of: 2500, 3000, 3100, 3200
+
+- qcom,charger-disable:
+ Usage: optional
+ Value type: <boolean>
+ Definition: defining this property disables charging
+
+This charger is a sub-node of one of the 8941 PMIC blocks, and is specified
+as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and
+../mfd/qcom-pm8xxx.txt
+
+Example:
+
+ pm8941@0 {
+ coincell@2800 {
+ compatible = "qcom,pm8941-coincell";
+ reg = <0x2800>;
+
+ qcom,rset-ohms = <2100>;
+ qcom,vset-millivolts = <3000>;
+ };
+ };
--- /dev/null
+Qualcomm Switch-Mode Battery Charger and Boost
+
+PROPERTIES
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Description: Must be one of:
+ - "qcom,pm8941-charger"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Description: Base address of registers for SMBB block
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Description: The format of the specifier is defined by the binding document
+ describing the node's interrupt parent. Must contain one
+ specifier for each of the following interrupts, in order:
+ - charge done
+ - charge fast mode
+ - charge trickle mode
+ - battery temperature ok
+ - battery present
+ - charger disconnected
+ - USB-in valid
+ - DC-in valid
+
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Description: Must contain the following list, strictly ordered:
+ "chg-done",
+ "chg-fast",
+ "chg-trkl",
+ "bat-temp-ok",
+ "bat-present",
+ "chg-gone",
+ "usb-valid",
+ "dc-valid"
+
+- qcom,fast-charge-current-limit:
+ Usage: optional (default: 1A, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 3A]
+ Description: Maximum charge current; May be clamped to safety limits.
+
+- qcom,fast-charge-low-threshold-voltage:
+ Usage: optional (default: 3.2V, or pre-configured value)
+ Value type: <u32>; uV; range [2.1V : 3.6V]
+ Description: Battery voltage limit above which fast charging may operate;
+ Below this value linear or switch-mode auto-trickle-charging
+ will operate.
+
+- qcom,fast-charge-high-threshold-voltage:
+ Usage: optional (default: 4.2V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Battery voltage limit below which fast charging may operate;
+ The fast charger will attempt to charge the battery to this
+ voltage. May be clamped to safety limits.
+
+- qcom,fast-charge-safe-voltage:
+ Usage: optional (default: 4.2V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Maximum safe battery voltage; May be pre-set by bootloader, in
+ which case, setting this will harmlessly fail. The property
+ 'fast-charge-high-watermark' will be clamped by this value.
+
+- qcom,fast-charge-safe-current:
+ Usage: optional (default: 1A, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 3A]
+ Description: Maximum safe battery charge current; May pre-set by bootloader,
+ in which case, setting this will harmlessly fail. The property
+ 'qcom,fast-charge-current-limit' will be clamped by this value.
+
+- qcom,auto-recharge-threshold-voltage:
+ Usage: optional (default: 4.1V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Battery voltage limit below which auto-recharge functionality
+ will restart charging after end-of-charge; The high cutoff
+ limit for auto-recharge is 5% above this value.
+
+- qcom,minimum-input-voltage:
+ Usage: optional (default: 4.3V, or pre-configured value)
+ Value type: <u32>; uV; range [4.2V : 9.6V]
+ Description: Input voltage level above which charging may operate
+
+- qcom,dc-current-limit:
+ Usage: optional (default: 100mA, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 2.5A]
+ Description: Default DC charge current limit
+
+- qcom,disable-dc:
+ Usage: optional (default: false)
+ Value type: boolean: <u32> or <empty>
+ Description: Disable DC charger
+
+- qcom,jeita-extended-temp-range:
+ Usage: optional (default: false)
+ Value type: boolean: <u32> or <empty>
+ Description: Enable JEITA extended temperature range; This does *not*
+ adjust the maximum charge voltage or current in the extended
+ temperature range. It only allows charging when the battery
+ is in the extended temperature range. Voltage/current
+ regulation must be done externally to fully comply with
+ the JEITA safety guidelines if this flag is set.
+
+EXAMPLE
+charger@1000 {
+ compatible = "qcom,pm8941-charger";
+ reg = <0x1000 0x700>;
+ interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+ interrupt-names = "chg-done",
+ "chg-fast",
+ "chg-trkl",
+ "bat-temp-ok",
+ "bat-present",
+ "chg-gone",
+ "usb-valid",
+ "dc-valid";
+
+ qcom,fast-charge-current-limit = <1000000>;
+ qcom,dc-charge-current-limit = <1000000>;
+};
--- /dev/null
+Binding for Richtek rt9455 battery charger
+
+Required properties:
+- compatible: it should contain one of the following:
+ "richtek,rt9455".
+- reg: integer, i2c address of the device.
+- interrupt-parent: the phandle for the interrupt controller that
+ services interrupts for this device.
+- interrupts: interrupt mapping for GPIO IRQ, it should be
+ configured with IRQ_TYPE_LEVEL_LOW flag.
+- richtek,output-charge-current: integer, output current from the charger to the
+ battery, in uA.
+- richtek,end-of-charge-percentage: integer, percent of the output charge current.
+ When the current in constant-voltage phase drops
+ below output_charge_current x end-of-charge-percentage,
+ charge is terminated.
+- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV.
+- richtek,boost-output-voltage: integer, maximum voltage provided to consumer
+ devices, when the charger is in boost mode, in uV.
+
+Optional properties:
+- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to
+ decrease voltage level when the over current
+ of the input power source occurs.
+ This prevents input voltage drop due to insufficient
+ current provided by the power source.
+ Default: 4500000 uV (4.5V)
+- richtek,avg-input-current-regulation: integer, input current value in uA drained by the
+ charger from the power source.
+ Default: 500000 uA (500mA)
+
+Example:
+
+rt9455@22 {
+ compatible = "richtek,rt9455";
+ reg = <0x22>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ richtek,output-charge-current = <500000>;
+ richtek,end-of-charge-percentage = <10>;
+ richtek,battery-regulation-voltage = <4200000>;
+ richtek,boost-output-voltage = <5050000>;
+
+ richtek,min-input-voltage-regulation = <4500000>;
+ richtek,avg-input-current-regulation = <500000>;
+};
--- /dev/null
+Binding for Nokia N900 battery
+
+The Nokia N900 battery status can be read via the TWL4030's A/D converter.
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nokia,n900-battery"
+- io-channels: Should contain IIO channel specifiers
+ for each element in io-channel-names.
+- io-channel-names: Should contain the following values:
+ * "temp" - The ADC channel for temperature reading
+ * "bsi" - The ADC channel for battery size identification
+ * "vbat" - The ADC channel to measure the battery voltage
+
+Example from Nokia N900:
+
+battery: n900-battery {
+ compatible = "nokia,n900-battery";
+ io-channels = <&twl4030_madc 0>,
+ <&twl4030_madc 4>,
+ <&twl4030_madc 12>;
+ io-channel-names = "temp",
+ "bsi",
+ "vbat";
+};
--- /dev/null
+SBS sbs-battery
+~~~~~~~~~~
+
+Required properties :
+ - compatible : "sbs,sbs-battery"
+
+Optional properties :
+ - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c
+ IO failure.
+ - sbs,poll-retry-count : The number of times to try looking for new status
+ after an external change notification.
+ - sbs,battery-detect-gpios : The gpio which signals battery detection and
+ a flag specifying its polarity.
+
+Example:
+
+ bq20z75@b {
+ compatible = "sbs,sbs-battery";
+ reg = < 0xb >;
+ sbs,i2c-retry-count = <2>;
+ sbs,poll-retry-count = <10>;
+ sbs,battery-detect-gpios = <&gpio-controller 122 1>;
+ }
--- /dev/null
+TI BQ24735 Charge Controller
+~~~~~~~~~~
+
+Required properties :
+ - compatible : "ti,bq24735"
+
+Optional properties :
+ - interrupts : Specify the interrupt to be used to trigger when the AC
+ adapter is either plugged in or removed.
+ - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter
+ presence. This is a Host GPIO that is configured as an input and
+ connected to the bq24735.
+ - ti,charge-current : Used to control and set the charging current. This value
+ must be between 128mA and 8.128A with a 64mA step resolution. The POR value
+ is 0x0000h. This number is in mA (e.g. 8192), see spec for more information
+ about the ChargeCurrent (0x14h) register.
+ - ti,charge-voltage : Used to control and set the charging voltage. This value
+ must be between 1.024V and 19.2V with a 16mV step resolution. The POR value
+ is 0x0000h. This number is in mV (e.g. 19200), see spec for more information
+ about the ChargeVoltage (0x15h) register.
+ - ti,input-current : Used to control and set the charger input current. This
+ value must be between 128mA and 8.064A with a 128mA step resolution. The
+ POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for
+ more information about the InputCurrent (0x3fh) register.
+ - ti,external-control : Indicates that the charger is configured externally
+ and that the host should not attempt to enable/disable charging or set the
+ charge voltage/current.
+
+Example:
+
+ bq24735@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+ ti,ac-detect-gpios = <&gpio 72 0x1>;
+ }
--- /dev/null
+TPS65090 Frontend PMU with Switchmode Charger
+
+Required Properties:
+-compatible: "ti,tps65090-charger"
+
+Optional Properties:
+-ti,enable-low-current-chrg: Enables charging when a low current is detected
+ while the default logic is to stop charging.
+
+This node is a subnode of the tps65090 PMIC.
+
+Example:
+
+ tps65090-charger {
+ compatible = "ti,tps65090-charger";
+ ti,enable-low-current-chrg;
+ };
--- /dev/null
+TPS65217 Charger
+
+Required Properties:
+-compatible: "ti,tps65217-charger"
+
+This node is a subnode of the tps65217 PMIC.
+
+Example:
+
+ tps65217-charger {
+ compatible = "ti,tps65090-charger";
+ };
--- /dev/null
+TWL BCI (Battery Charger Interface)
+
+The battery charger needs to interact with the USB phy in order
+to know when charging is permissible, and when there is a connection
+or disconnection.
+
+The choice of phy cannot be configured at a hardware level, so there
+is no value in explicit configuration in device-tree. Rather
+if there is a sibling of the BCI node which is compatible with
+"ti,twl4030-usb", then that is used to determine when and how
+use USB power for charging.
+
+Required properties:
+- compatible:
+ - "ti,twl4030-bci"
+- interrupts: two interrupt lines from the TWL SIH (secondary
+ interrupt handler) - interrupts 9 and 2.
+
+Optional properties:
+- ti,bb-uvolt: microvolts for charging the backup battery.
+- ti,bb-uamp: microamps for charging the backup battery.
+
+Examples:
+
+bci {
+ compatible = "ti,twl4030-bci";
+ interrupts = <9>, <2>;
+ ti,bb-uvolt = <3200000>;
+ ti,bb-uamp = <150>;
+};
+++ /dev/null
-TWL BCI (Battery Charger Interface)
-
-The battery charger needs to interact with the USB phy in order
-to know when charging is permissible, and when there is a connection
-or disconnection.
-
-The choice of phy cannot be configured at a hardware level, so there
-is no value in explicit configuration in device-tree. Rather
-if there is a sibling of the BCI node which is compatible with
-"ti,twl4030-usb", then that is used to determine when and how
-use USB power for charging.
-
-Required properties:
-- compatible:
- - "ti,twl4030-bci"
-- interrupts: two interrupt lines from the TWL SIH (secondary
- interrupt handler) - interrupts 9 and 2.
-
-Optional properties:
-- ti,bb-uvolt: microvolts for charging the backup battery.
-- ti,bb-uamp: microamps for charging the backup battery.
-
-Examples:
-
-bci {
- compatible = "ti,twl4030-bci";
- interrupts = <9>, <2>;
- ti,bb-uvolt = <3200000>;
- ti,bb-uamp = <150>;
-};
+++ /dev/null
-=== AB8500 Battery Temperature Monitor Driver ===
-
-The properties below describes the node for btemp driver.
-
-Required Properties:
-- compatible = Shall be: "stericsson,ab8500-btemp"
-- battery = Shall be battery specific information
-
- Example:
- ab8500_btemp {
- compatible = "stericsson,ab8500-btemp";
- battery = <&ab8500_battery>;
- };
-
-For information on battery specific node, Ref:
-Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
+++ /dev/null
-=== AB8500 Charging Algorithm Driver ===
-
-The properties below describes the node for chargalg driver.
-
-Required Properties:
-- compatible = Shall be: "stericsson,ab8500-chargalg"
-- battery = Shall be battery specific information
-
-Example:
-ab8500_chargalg {
- compatible = "stericsson,ab8500-chargalg";
- battery = <&ab8500_battery>;
-};
-
-For information on battery specific node, Ref:
-Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
+++ /dev/null
-=== AB8500 Charger Driver ===
-
-Required Properties:
-- compatible = Shall be "stericsson,ab8500-charger"
-- battery = Shall be battery specific information
- Example:
- ab8500_charger {
- compatible = "stericsson,ab8500-charger";
- battery = <&ab8500_battery>;
- };
-
-- vddadc-supply: Supply for USB and Main charger
- Example:
- ab8500-charger {
- vddadc-supply = <&ab8500_ldo_tvout_reg>;
- }
-- autopower_cfg:
- Boolean value depicting the presence of 'automatic poweron after powerloss'
- Example:
- ab8500-charger {
- autopower_cfg;
- };
-
-For information on battery specific node, Ref:
-Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
+++ /dev/null
-=== AB8500 Fuel Gauge Driver ===
-
-AB8500 is a mixed signal multimedia and power management
-device comprising: power and energy-management-module,
-wall-charger, usb-charger, audio codec, general purpose adc,
-tvout, clock management and sim card interface.
-
-Fuelgauge support is part of energy-management-modules, other
-components of this module are:
-main-charger, usb-combo-charger and battery-temperature-monitoring.
-
-The properties below describes the node for fuelgauge driver.
-
-Required Properties:
-- compatible = This shall be: "stericsson,ab8500-fg"
-- battery = Shall be battery specific information
- Example:
- ab8500_fg {
- compatible = "stericsson,ab8500-fg";
- battery = <&ab8500_battery>;
- };
-
-dependent node:
- ab8500_battery: ab8500_battery {
- };
- This node will provide information on 'thermistor interface' and
- 'battery technology type' used.
-
-Properties of this node are:
-thermistor-on-batctrl:
- A boolean value indicating thermistor interface to battery
-
- Note:
- 'btemp' and 'batctrl' are the pins interfaced for battery temperature
- measurement, 'btemp' signal is used when NTC(negative temperature
- coefficient) resister is interfaced external to battery whereas
- 'batctrl' pin is used when NTC resister is internal to battery.
-
- Example:
- ab8500_battery: ab8500_battery {
- thermistor-on-batctrl;
- };
- indicates: NTC resister is internal to battery, 'batctrl' is used
- for thermal measurement.
-
- The absence of property 'thermal-on-batctrl' indicates
- NTC resister is external to battery and 'btemp' signal is used
- for thermal measurement.
-
-battery-type:
- This shall be the battery manufacturing technology type,
- allowed types are:
- "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn"
- Example:
- ab8500_battery: ab8500_battery {
- stericsson,battery-type = "LIPO";
- }
-
+++ /dev/null
-AXP20x USB power supply
-
-Required Properties:
--compatible: One of: "x-powers,axp202-usb-power-supply"
- "x-powers,axp221-usb-power-supply"
-
-This node is a subnode of the axp20x PMIC.
-
-Example:
-
-axp209: pmic@34 {
- compatible = "x-powers,axp209";
- reg = <0x34>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
-
- regulators {
- x-powers,dcdc-freq = <1500>;
-
- vdd_cpu: dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1450000>;
- regulator-name = "vdd-cpu";
- };
-
- ...
- };
-
- usb-power-supply: usb-power-supply {
- compatible = "x-powers,axp202-usb-power-supply";
- };
-};
+++ /dev/null
-Axxia Restart Driver
-
-This driver can do reset of the Axxia SoC. It uses the registers in the syscon
-block to initiate a chip reset.
-
-Required Properties:
- -compatible: "lsi,axm55xx-reset"
- -syscon: phandle to the syscon node.
-
-Example:
-
- syscon: syscon@2010030000 {
- compatible = "lsi,axxia-syscon", "syscon";
- reg = <0x20 0x10030000 0 0x2000>;
- };
-
- reset: reset@2010031000 {
- compatible = "lsi,axm55xx-reset";
- syscon = <&syscon>;
- };
+++ /dev/null
-charger-manager bindings
-~~~~~~~~~~~~~~~~~~~~~~~~
-
-Required properties :
- - compatible : "charger-manager"
- - <>-supply : for regulator consumer
- - cm-num-chargers : number of chargers
- - cm-chargers : name of chargers
- - cm-fuel-gauge : name of battery fuel gauge
- - subnode <regulator> :
- - cm-regulator-name : name of charger regulator
- - subnode <cable> :
- - cm-cable-name : name of charger cable
- - cm-cable-extcon : name of extcon dev
-(optional) - cm-cable-min : minimum current of cable
-(optional) - cm-cable-max : maximum current of cable
-
-Optional properties :
- - cm-name : charger manager's name (default : "battery")
- - cm-poll-mode : polling mode (enum polling_modes)
- - cm-poll-interval : polling interval
- - cm-battery-stat : battery status (enum data_source)
- - cm-fullbatt-* : data for full battery checking
- - cm-thermal-zone : name of external thermometer's thermal zone
- - cm-battery-* : threshold battery temperature for charging
- -cold : critical cold temperature of battery for charging
- -cold-in-minus : flag that cold temperature is in minus degrees
- -hot : critical hot temperature of battery for charging
- -temp-diff : temperature difference to allow recharging
- - cm-dis/charging-max = limits of charging duration
-
-Example :
- charger-manager@0 {
- compatible = "charger-manager";
- chg-reg-supply = <&charger_regulator>;
-
- cm-name = "battery";
- /* Always polling ON : 30s */
- cm-poll-mode = <1>;
- cm-poll-interval = <30000>;
-
- cm-fullbatt-vchkdrop-ms = <30000>;
- cm-fullbatt-vchkdrop-volt = <150000>;
- cm-fullbatt-soc = <100>;
-
- cm-battery-stat = <3>;
-
- cm-num-chargers = <3>;
- cm-chargers = "charger0", "charger1", "charger2";
-
- cm-fuel-gauge = "fuelgauge0";
-
- cm-thermal-zone = "thermal_zone.1"
- /* in deci centigrade */
- cm-battery-cold = <50>;
- cm-battery-cold-in-minus;
- cm-battery-hot = <800>;
- cm-battery-temp-diff = <100>;
-
- /* Allow charging for 5hr */
- cm-charging-max = <18000000>;
- /* Allow discharging for 2hr */
- cm-discharging-max = <7200000>;
-
- regulator@0 {
- cm-regulator-name = "chg-reg";
- cable@0 {
- cm-cable-name = "USB";
- cm-cable-extcon = "extcon-dev.0";
- cm-cable-min = <475000>;
- cm-cable-max = <500000>;
- };
- cable@1 {
- cm-cable-name = "TA";
- cm-cable-extcon = "extcon-dev.0";
- cm-cable-min = <650000>;
- cm-cable-max = <675000>;
- };
- };
-
- };
+++ /dev/null
-gpio-charger
-
-Required properties :
- - compatible : "gpio-charger"
- - gpios : GPIO indicating the charger presence.
- See GPIO binding in bindings/gpio/gpio.txt .
- - charger-type : power supply type, one of
- unknown
- battery
- ups
- mains
- usb-sdp (USB standard downstream port)
- usb-dcp (USB dedicated charging port)
- usb-cdp (USB charging downstream port)
- usb-aca (USB accessory charger adapter)
-
-Example:
-
- usb_charger: charger {
- compatible = "gpio-charger";
- charger-type = "usb-sdp";
- gpios = <&gpf0 2 0 0 0>;
- }
-
- battery {
- power-supplies = <&usb_charger>;
- };
+++ /dev/null
-i.mx6 Poweroff Driver
-
-SNVS_LPCR in SNVS module can power off the whole system by pull
-PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC.
-If you don't want to use PMIC_ON_REQ as power on/off control,
-please set status='disabled' to disable this driver.
-
-Required Properties:
--compatible: "fsl,sec-v4.0-poweroff"
--reg: Specifies the physical address of the SNVS_LPCR register
-
-Example:
- snvs@020cc000 {
- compatible = "fsl,sec-v4.0-mon", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x020cc000 0x4000>;
- .....
- snvs_poweroff: snvs-poweroff@38 {
- compatible = "fsl,sec-v4.0-poweroff";
- reg = <0x38 0x4>;
- };
- }
+++ /dev/null
-Binding for TI/National Semiconductor LP8727 Charger
-
-Required properties:
-- compatible: "ti,lp8727"
-- reg: I2C slave address 27h
-
-Optional properties:
-- interrupt-parent: interrupt controller node (see interrupt binding[0])
-- interrupts: interrupt specifier (see interrupt binding[0])
-- debounce-ms: interrupt debounce time. (u32)
-
-AC and USB charging parameters
-- charger-type: "ac" or "usb" (string)
-- eoc-level: value of 'enum lp8727_eoc_level' (u8)
-- charging-current: value of 'enum lp8727_ichg' (u8)
-
-[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-Example)
-
-lp8727@27 {
- compatible = "ti,lp8727";
- reg = <0x27>;
-
- /* GPIO 134 is used for LP8728 interrupt pin */
- interrupt-parent = <&gpio5>; /* base = 128 */
- interrupts = <6 0x2>; /* offset = 6, falling edge type */
-
- debounce-ms = <300>;
-
- /* AC charger: 5% EOC and 500mA charging current */
- ac {
- charger-type = "ac";
- eoc-level = /bits/ 8 <0>;
- charging-current = /bits/ 8 <4>;
- };
-
- /* USB charger: 10% EOC and 400mA charging current */
- usb {
- charger-type = "usb";
- eoc-level = /bits/ 8 <1>;
- charging-current = /bits/ 8 <2>;
- };
-};
+++ /dev/null
-max17042_battery
-~~~~~~~~~~~~~~~~
-
-Required properties :
- - compatible : "maxim,max17042"
-
-Optional properties :
- - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms
- (datasheet-recommended value is 10000).
- Defining this property enables current-sense functionality.
-
-Optional threshold properties :
- If skipped the condition won't be reported.
- - maxim,cold-temp : Temperature threshold to report battery
- as cold (in tenths of degree Celsius).
- - maxim,over-heat-temp : Temperature threshold to report battery
- as over heated (in tenths of degree Celsius).
- - maxim,dead-volt : Voltage threshold to report battery
- as dead (in mV).
- - maxim,over-volt : Voltage threshold to report battery
- as over voltage (in mV).
-
-Example:
-
- battery-charger@36 {
- compatible = "maxim,max17042";
- reg = <0x36>;
- maxim,rsns-microohm = <10000>;
- maxim,over-heat-temp = <600>;
- maxim,over-volt = <4300>;
- };
+++ /dev/null
-max8925-battery bindings
-~~~~~~~~~~~~~~~~
-
-Optional properties :
- - batt-detect: whether support battery detect
- - topoff-threshold: set charging current in topoff mode
- - fast-charge: set charging current in fast mode
- - no-temp-support: whether support temperature protection detect
- - no-insert-detect: whether support insert detect
-
-Example:
- charger {
- batt-detect = <0>;
- topoff-threshold = <1>;
- fast-charge = <7>;
- no-temp-support = <0>;
- no-insert-detect = <0>;
- };
+++ /dev/null
-MSM Restart Driver
-
-A power supply hold (ps-hold) bit is set to power the msm chipsets.
-Clearing that bit allows us to restart/poweroff. The difference
-between poweroff and restart is determined by unique power manager IC
-settings.
-
-Required Properties:
--compatible: "qcom,pshold"
--reg: Specifies the physical address of the ps-hold register
-
-Example:
-
- restart@fc4ab000 {
- compatible = "qcom,pshold";
- reg = <0xfc4ab000 0x4>;
- };
+++ /dev/null
-OLPC battery
-~~~~~~~~~~~~
-
-Required properties:
- - compatible : "olpc,xo1-battery"
+++ /dev/null
-Power Supply Core Support
-
-Optional Properties:
- - power-supplies : This property is added to a supply in order to list the
- devices which supply it power, referenced by their phandles.
-
-Example:
-
- usb-charger: power@e {
- compatible = "some,usb-charger";
- ...
- };
-
- ac-charger: power@c {
- compatible = "some,ac-charger";
- ...
- };
-
- battery@b {
- compatible = "some,battery";
- ...
- power-supplies = <&usb-charger>, <&ac-charger>;
- };
+++ /dev/null
-Qualcomm Switch-Mode Battery Charger and Boost
-
-PROPERTIES
-- compatible:
- Usage: required
- Value type: <stringlist>
- Description: Must be one of:
- - "qcom,pm8941-charger"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Description: Base address of registers for SMBB block
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Description: The format of the specifier is defined by the binding document
- describing the node's interrupt parent. Must contain one
- specifier for each of the following interrupts, in order:
- - charge done
- - charge fast mode
- - charge trickle mode
- - battery temperature ok
- - battery present
- - charger disconnected
- - USB-in valid
- - DC-in valid
-
-- interrupt-names:
- Usage: required
- Value type: <stringlist>
- Description: Must contain the following list, strictly ordered:
- "chg-done",
- "chg-fast",
- "chg-trkl",
- "bat-temp-ok",
- "bat-present",
- "chg-gone",
- "usb-valid",
- "dc-valid"
-
-- qcom,fast-charge-current-limit:
- Usage: optional (default: 1A, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 3A]
- Description: Maximum charge current; May be clamped to safety limits.
-
-- qcom,fast-charge-low-threshold-voltage:
- Usage: optional (default: 3.2V, or pre-configured value)
- Value type: <u32>; uV; range [2.1V : 3.6V]
- Description: Battery voltage limit above which fast charging may operate;
- Below this value linear or switch-mode auto-trickle-charging
- will operate.
-
-- qcom,fast-charge-high-threshold-voltage:
- Usage: optional (default: 4.2V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Battery voltage limit below which fast charging may operate;
- The fast charger will attempt to charge the battery to this
- voltage. May be clamped to safety limits.
-
-- qcom,fast-charge-safe-voltage:
- Usage: optional (default: 4.2V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Maximum safe battery voltage; May be pre-set by bootloader, in
- which case, setting this will harmlessly fail. The property
- 'fast-charge-high-watermark' will be clamped by this value.
-
-- qcom,fast-charge-safe-current:
- Usage: optional (default: 1A, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 3A]
- Description: Maximum safe battery charge current; May pre-set by bootloader,
- in which case, setting this will harmlessly fail. The property
- 'qcom,fast-charge-current-limit' will be clamped by this value.
-
-- qcom,auto-recharge-threshold-voltage:
- Usage: optional (default: 4.1V, or pre-configured value)
- Value type: <u32>; uV; range [3.24V : 5V]
- Description: Battery voltage limit below which auto-recharge functionality
- will restart charging after end-of-charge; The high cutoff
- limit for auto-recharge is 5% above this value.
-
-- qcom,minimum-input-voltage:
- Usage: optional (default: 4.3V, or pre-configured value)
- Value type: <u32>; uV; range [4.2V : 9.6V]
- Description: Input voltage level above which charging may operate
-
-- qcom,dc-current-limit:
- Usage: optional (default: 100mA, or pre-configured value)
- Value type: <u32>; uA; range [100mA : 2.5A]
- Description: Default DC charge current limit
-
-- qcom,disable-dc:
- Usage: optional (default: false)
- Value type: boolean: <u32> or <empty>
- Description: Disable DC charger
-
-- qcom,jeita-extended-temp-range:
- Usage: optional (default: false)
- Value type: boolean: <u32> or <empty>
- Description: Enable JEITA extended temperature range; This does *not*
- adjust the maximum charge voltage or current in the extended
- temperature range. It only allows charging when the battery
- is in the extended temperature range. Voltage/current
- regulation must be done externally to fully comply with
- the JEITA safety guidelines if this flag is set.
-
-EXAMPLE
-charger@1000 {
- compatible = "qcom,pm8941-charger";
- reg = <0x1000 0x700>;
- interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
- <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
- interrupt-names = "chg-done",
- "chg-fast",
- "chg-trkl",
- "bat-temp-ok",
- "bat-present",
- "chg-gone",
- "usb-valid",
- "dc-valid";
-
- qcom,fast-charge-current-limit = <1000000>;
- qcom,dc-charge-current-limit = <1000000>;
-};
+++ /dev/null
-* QNAP Power Off
-
-QNAP NAS devices have a microcontroller controlling the main power
-supply. This microcontroller is connected to UART1 of the Kirkwood and
-Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the
-microcontroller to turn the power off. This driver adds a handler to
-pm_power_off which is called to turn the power off.
-
-Synology NAS devices use a similar scheme, but a different baud rate,
-9600, and a different character, '1'.
-
-Required Properties:
-- compatible: Should be "qnap,power-off" or "synology,power-off"
-
-- reg: Address and length of the register set for UART1
-- clocks: tclk clock
+++ /dev/null
-* Restart Power Off
-
-Buffalo Linkstation LS-XHL and LS-CHLv2, and other devices power off
-by restarting and letting u-boot keep hold of the machine until the
-user presses a button.
-
-Required Properties:
-- compatible: Should be "restart-poweroff"
+++ /dev/null
-SBS sbs-battery
-~~~~~~~~~~
-
-Required properties :
- - compatible : "sbs,sbs-battery"
-
-Optional properties :
- - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c
- IO failure.
- - sbs,poll-retry-count : The number of times to try looking for new status
- after an external change notification.
- - sbs,battery-detect-gpios : The gpio which signals battery detection and
- a flag specifying its polarity.
-
-Example:
-
- bq20z75@b {
- compatible = "sbs,sbs-battery";
- reg = < 0xb >;
- sbs,i2c-retry-count = <2>;
- sbs,poll-retry-count = <10>;
- sbs,battery-detect-gpios = <&gpio-controller 122 1>;
- }
+++ /dev/null
-TI BQ24735 Charge Controller
-~~~~~~~~~~
-
-Required properties :
- - compatible : "ti,bq24735"
-
-Optional properties :
- - interrupts : Specify the interrupt to be used to trigger when the AC
- adapter is either plugged in or removed.
- - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter
- presence. This is a Host GPIO that is configured as an input and
- connected to the bq24735.
- - ti,charge-current : Used to control and set the charging current. This value
- must be between 128mA and 8.128A with a 64mA step resolution. The POR value
- is 0x0000h. This number is in mA (e.g. 8192), see spec for more information
- about the ChargeCurrent (0x14h) register.
- - ti,charge-voltage : Used to control and set the charging voltage. This value
- must be between 1.024V and 19.2V with a 16mV step resolution. The POR value
- is 0x0000h. This number is in mV (e.g. 19200), see spec for more information
- about the ChargeVoltage (0x15h) register.
- - ti,input-current : Used to control and set the charger input current. This
- value must be between 128mA and 8.064A with a 128mA step resolution. The
- POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for
- more information about the InputCurrent (0x3fh) register.
- - ti,external-control : Indicates that the charger is configured externally
- and that the host should not attempt to enable/disable charging or set the
- charge voltage/current.
-
-Example:
-
- bq24735@9 {
- compatible = "ti,bq24735";
- reg = <0x9>;
- ti,ac-detect-gpios = <&gpio 72 0x1>;
- }
+++ /dev/null
-TPS65090 Frontend PMU with Switchmode Charger
-
-Required Properties:
--compatible: "ti,tps65090-charger"
-
-Optional Properties:
--ti,enable-low-current-chrg: Enables charging when a low current is detected
- while the default logic is to stop charging.
-
-This node is a subnode of the tps65090 PMIC.
-
-Example:
-
- tps65090-charger {
- compatible = "ti,tps65090-charger";
- ti,enable-low-current-chrg;
- };
+++ /dev/null
-TPS65217 Charger
-
-Required Properties:
--compatible: "ti,tps65217-charger"
-
-This node is a subnode of the tps65217 PMIC.
-
-Example:
-
- tps65217-charger {
- compatible = "ti,tps65090-charger";
- };
L: linux-pm@vger.kernel.org
T: git git://git.infradead.org/battery-2.6.git
S: Maintained
-F: Documentation/devicetree/bindings/power/
-F: Documentation/devicetree/bindings/power_supply/
+F: Documentation/devicetree/bindings/power/supply/
F: include/linux/power_supply.h
F: drivers/power/supply/
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff