arm: vf610: zii devel b: Add support for switch interrupts

The Switches use GPIO lines to indicate interrupts from two of the
switches.

With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
index 5c1fcab4a6f78d9f340f67b1805427933cea5ad6..1552db00cc592e0a17465c702b74428310b343b0 100644 (file)
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -88,10 +88,16 @@
 
                        switch0: switch0@0 {
                                compatible = "marvell,mv88e6085";
+                               pinctrl-0 = <&pinctrl_gpio_switch0>;
+                               pinctrl-names = "default";
                                #address-cells = <1>;
                                #size-cells = <0>;
                                reg = <0>;
                                dsa,member = <0 0>;
+                               interrupt-parent = <&gpio0>;
+                               interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+                               interrupt-controller;
+                               #interrupt-cells = <2>;
 
                                ports {
                                        #address-cells = <1>;
@@ -99,16 +105,19 @@
                                        port@0 {
                                                reg = <0>;
                                                label = "lan0";
+                                               phy-handle = <&switch0phy0>;
                                        };
 
                                        port@1 {
                                                reg = <1>;
                                                label = "lan1";
+                                               phy-handle = <&switch0phy1>;
                                        };
 
                                        port@2 {
                                                reg = <2>;
                                                label = "lan2";
+                                               phy-handle = <&switch0phy2>;
                                        };
 
                                        switch0port5: port@5 {
@@ -133,6 +142,24 @@
                                                };
                                        };
                                };
+                               mdio {
+                                       #address-cells = <1>;
+                                       #size-cells = <0>;
+                                       switch0phy0: switch0phy0@0 {
+                                               reg = <0>;
+                                               interrupt-parent = <&switch0>;
+                                               interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+                                       };
+                                       switch0phy1: switch1phy0@1 {
+                                               reg = <1>;
+                                               interrupt-parent = <&switch0>;
+                                               interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;                                   };
+                                       switch0phy2: switch1phy0@2 {
+                                               reg = <2>;
+                                               interrupt-parent = <&switch0>;
+                                               interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+                                       };
+                               };
                        };
                };
 
@@ -143,10 +170,16 @@
 
                        switch1: switch1@0 {
                                compatible = "marvell,mv88e6085";
+                               pinctrl-0 = <&pinctrl_gpio_switch1>;
+                               pinctrl-names = "default";
                                #address-cells = <1>;
                                #size-cells = <0>;
                                reg = <0>;
                                dsa,member = <0 1>;
+                               interrupt-parent = <&gpio0>;
+                               interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+                               interrupt-controller;
+                               #interrupt-cells = <2>;
 
                                ports {
                                        #address-cells = <1>;
@@ -196,12 +229,18 @@
                                        #size-cells = <0>;
                                        switch1phy0: switch1phy0@0 {
                                                reg = <0>;
+                                               interrupt-parent = <&switch1>;
+                                               interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
                                        };
                                        switch1phy1: switch1phy0@1 {
                                                reg = <1>;
+                                               interrupt-parent = <&switch1>;
+                                               interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
                                        };
                                        switch1phy2: switch1phy0@2 {
                                                reg = <2>;
+                                               interrupt-parent = <&switch1>;
+                                               interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
                                        };
                                };
                        };
@@ -636,6 +675,18 @@
                >;
        };
 
+       pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+               fsl,pins = <
+                       VF610_PAD_PTB5__GPIO_27         0x219d
+               >;
+       };
+
+       pinctrl_gpio_switch1: pinctrl-gpio-switch1 {
+               fsl,pins = <
+                       VF610_PAD_PTB4__GPIO_26         0x219d
+               >;
+       };
+
        pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
                fsl,pins = <
                         VF610_PAD_PTE14__GPIO_119      0x31c2