bnx2: Reinsert VLAN tag when necessary.
authorMichael Chan <mchan@broadcom.com>
Thu, 14 Aug 2008 22:30:14 +0000 (15:30 -0700)
committerDavid S. Miller <davem@davemloft.net>
Thu, 14 Aug 2008 22:30:14 +0000 (15:30 -0700)
In certain cases when ASF or other management firmware is running, the
chip may be configured to always strip out the VLAN tag even when
VLAN acceleration is not enabled.  This causes some VLAN tagged
packets to be received by the host stack without any knowledge that
the original packet was VLAN tagged.

We fix this by re-inserting the VLAN tag into the packet when necessary.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bnx2.c

index a2a010ede591d1d82a144a0ab54a86f6443d6f50..1f2e76fda01e542092645dcbaaf124dfe90c8227 100644 (file)
@@ -2876,6 +2876,8 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget)
                struct sw_bd *rx_buf;
                struct sk_buff *skb;
                dma_addr_t dma_addr;
+               u16 vtag = 0;
+               int hw_vlan __maybe_unused = 0;
 
                sw_ring_cons = RX_RING_IDX(sw_cons);
                sw_ring_prod = RX_RING_IDX(sw_prod);
@@ -2919,7 +2921,7 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget)
                if (len <= bp->rx_copy_thresh) {
                        struct sk_buff *new_skb;
 
-                       new_skb = netdev_alloc_skb(bp->dev, len + 2);
+                       new_skb = netdev_alloc_skb(bp->dev, len + 6);
                        if (new_skb == NULL) {
                                bnx2_reuse_rx_skb(bp, rxr, skb, sw_ring_cons,
                                                  sw_ring_prod);
@@ -2928,9 +2930,9 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget)
 
                        /* aligned copy */
                        skb_copy_from_linear_data_offset(skb,
-                                                        BNX2_RX_OFFSET - 2,
-                                     new_skb->data, len + 2);
-                       skb_reserve(new_skb, 2);
+                                                        BNX2_RX_OFFSET - 6,
+                                     new_skb->data, len + 6);
+                       skb_reserve(new_skb, 6);
                        skb_put(new_skb, len);
 
                        bnx2_reuse_rx_skb(bp, rxr, skb,
@@ -2941,6 +2943,25 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget)
                           dma_addr, (sw_ring_cons << 16) | sw_ring_prod)))
                        goto next_rx;
 
+               if ((status & L2_FHDR_STATUS_L2_VLAN_TAG) &&
+                   !(bp->rx_mode & BNX2_EMAC_RX_MODE_KEEP_VLAN_TAG)) {
+                       vtag = rx_hdr->l2_fhdr_vlan_tag;
+#ifdef BCM_VLAN
+                       if (bp->vlgrp)
+                               hw_vlan = 1;
+                       else
+#endif
+                       {
+                               struct vlan_ethhdr *ve = (struct vlan_ethhdr *)
+                                       __skb_push(skb, 4);
+
+                               memmove(ve, skb->data + 4, ETH_ALEN * 2);
+                               ve->h_vlan_proto = htons(ETH_P_8021Q);
+                               ve->h_vlan_TCI = htons(vtag);
+                               len += 4;
+                       }
+               }
+
                skb->protocol = eth_type_trans(skb, bp->dev);
 
                if ((len > (bp->dev->mtu + ETH_HLEN)) &&
@@ -2962,10 +2983,8 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget)
                }
 
 #ifdef BCM_VLAN
-               if ((status & L2_FHDR_STATUS_L2_VLAN_TAG) && bp->vlgrp) {
-                       vlan_hwaccel_receive_skb(skb, bp->vlgrp,
-                               rx_hdr->l2_fhdr_vlan_tag);
-               }
+               if (hw_vlan)
+                       vlan_hwaccel_receive_skb(skb, bp->vlgrp, vtag);
                else
 #endif
                        netif_receive_skb(skb);