ARM: dts: sun8i: Use the common file in NanoPi NEO SBC

NanoPi common dtsi supports all components of NEO SBC, so just include it.

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 3d64cafc1e90973d53fcf004981068ff347ec39a..8d2cc6e9a03faff3cc71965493e5c54c1359e9f3 100644 (file)
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -40,86 +40,9 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun8i-h3-nanopi.dtsi"
 
 / {
        model = "FriendlyARM NanoPi NEO";
        compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
-
-       aliases {
-               serial0 = &uart0;
-       };
-
-       chosen {
-               stdout-path = "serial0:115200n8";
-       };
-
-       leds {
-               compatible = "gpio-leds";
-               pinctrl-names = "default";
-               pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
-               pwr {
-                       label = "nanopi:green:pwr";
-                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-                       default-state = "on";
-               };
-
-               status {
-                       label = "nanopi:blue:status";
-                       gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
-               };
-       };
-};
-
-&ehci3 {
-       status = "okay";
-};
-
-&mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
-       vmmc-supply = <&reg_vcc3v3>;
-       bus-width = <4>;
-       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-       cd-inverted;
-       status = "okay";
-};
-
-&ohci3 {
-       status = "okay";
-};
-
-&pio {
-       leds_opc: led-pins {
-               allwinner,pins = "PA10";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-};
-
-&r_pio {
-       leds_r_opc: led-pins {
-               allwinner,pins = "PL10";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-};
-
-&uart0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
-       status = "okay";
-};
-
-&usbphy {
-       /* USB VBUS is always on */
-       status = "okay";
 };