--- /dev/null
+* ARM PrimeCell Color LCD Controller PL110/PL111
+
+See also Documentation/devicetree/bindings/arm/primecell.txt
+
+Required properties:
+
+- compatible: must be one of:
+ "arm,pl110", "arm,primecell"
+ "arm,pl111", "arm,primecell"
+
+- reg: base address and size of the control registers block
+
+- interrupt-names: either the single entry "combined" representing a
+ combined interrupt output (CLCDINTR), or the four entries
+ "mbe", "vcomp", "lnbu", "fuf" representing the individual
+ CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
+
+- interrupts: contains an interrupt specifier for each entry in
+ interrupt-names
+
+- clock-names: should contain "clcdclk" and "apb_pclk"
+
+- clocks: contains phandle and clock specifier pairs for the entries
+ in the clock-names property. See
+ Documentation/devicetree/binding/clock/clock-bindings.txt
+
+Optional properties:
+
+- memory-region: phandle to a node describing memory (see
+ Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
+ to be used for the framebuffer; if not present, the framebuffer
+ may be located anywhere in the memory
+
+- max-memory-bandwidth: maximum bandwidth in bytes per second that the
+ cell's memory interface can handle; if not present, the memory
+ interface is fast enough to handle all possible video modes
+
+Required sub-nodes:
+
+- port: describes LCD panel signals, following the common binding
+ for video transmitter interfaces; see
+ Documentation/devicetree/bindings/media/video-interfaces.txt;
+ when it is a TFT panel, the port's endpoint must define the
+ following property:
+
+ - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
+ defining the way CLD pads are wired up; first value
+ contains index of the "CLD" external pin (pad) used
+ as R0 (first bit of the red component), second value
+ index of the pad used as G0, third value index of the
+ pad used as B0, see also "LCD panel signal multiplexing
+ details" paragraphs in the PL110/PL111 Technical
+ Reference Manuals; this implicitly defines available
+ color modes, for example:
+ - PL111 TFT 4:4:4 panel:
+ arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
+ - PL110 TFT (1:)5:5:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
+ - PL111 TFT (1:)5:5:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
+ - PL111 TFT 5:6:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
+ - PL110 and PL111 TFT 8:8:8 panel:
+ arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+ - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
+ arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
+
+
+Example:
+
+ clcd@10020000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x10020000 0x1000>;
+ interrupt-names = "combined";
+ interrupts = <0 44 4>;
+ clocks = <&oscclk1>, <&oscclk2>;
+ clock-names = "clcdclk", "apb_pclk";
+ max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
+
+ port {
+ clcd_pads: endpoint {
+ remote-endpoint = <&clcd_panel>;
+ arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+ };
+ };
+
+ };
+
+ panel {
+ compatible = "panel-dpi";
+
+ port {
+ clcd_panel: endpoint {
+ remote-endpoint = <&clcd_pads>;
+ };
+ };
+
+ panel-timing {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ hback-porch = <40>;
+ hfront-porch = <24>;
+ hsync-len = <96>;
+ vactive = <480>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <2>;
+ };
+ };
--- /dev/null
+Device Tree bindings for Armada DRM CRTC driver
+
+Required properties:
+ - compatible: value should be "marvell,dove-lcd".
+ - reg: base address and size of the LCD controller
+ - interrupts: single interrupt number for the LCD controller
+ - port: video output port with endpoints, as described by graph.txt
+
+Optional properties:
+
+ - clocks: as described by clock-bindings.txt
+ - clock-names: as described by clock-bindings.txt
+ "axiclk" - axi bus clock for pixel clock
+ "plldivider" - pll divider clock for pixel clock
+ "ext_ref_clk0" - external clock 0 for pixel clock
+ "ext_ref_clk1" - external clock 1 for pixel clock
+
+Note: all clocks are optional but at least one must be specified.
+Further clocks may be added in the future according to requirements of
+different SoCs.
+
+Example:
+
+ lcd0: lcd-controller@820000 {
+ compatible = "marvell,dove-lcd";
+ reg = <0x820000 0x1000>;
+ interrupts = <47>;
+ clocks = <&si5351 0>;
+ clock-names = "ext_ref_clk_1";
+ };
--- /dev/null
+Atmel LCDC Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible :
+ "atmel,at91sam9261-lcdc" ,
+ "atmel,at91sam9263-lcdc" ,
+ "atmel,at91sam9g10-lcdc" ,
+ "atmel,at91sam9g45-lcdc" ,
+ "atmel,at91sam9g45es-lcdc" ,
+ "atmel,at91sam9rl-lcdc" ,
+ "atmel,at32ap-lcdc"
+- reg : Should contain 1 register ranges(address and length).
+ Can contain an additional register range(address and length)
+ for fixed framebuffer memory. Useful for dedicated memories.
+- interrupts : framebuffer controller interrupt
+- display: a phandle pointing to the display node
+
+Required nodes:
+- display: a display node is required to initialize the lcd panel
+ This should be in the board dts.
+- default-mode: a videomode within the display with timing parameters
+ as specified below.
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+
+Example:
+
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ display = <&display0>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ };
+
+Example for fixed framebuffer memory:
+
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9263-lcdc";
+ reg = <0x00700000 0x1000 0x70000000 0x200000>;
+ [...]
+ };
+
+Atmel LCDC Display
+-----------------------------------------------------
+Required properties (as per of_videomode_helper):
+
+ - atmel,dmacon: dma controller configuration
+ - atmel,lcdcon2: lcd controller configuration
+ - atmel,guard-time: lcd guard time (Delay in frame periods)
+ - bits-per-pixel: lcd panel bit-depth.
+
+Optional properties (as per of_videomode_helper):
+ - atmel,lcdcon-backlight: enable backlight
+ - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity
+ - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
+ - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
+
+Example:
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
--- /dev/null
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver
+
+The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device.
+See ../mfd/atmel-hlcdc.txt for more details.
+
+Required properties:
+ - compatible: value should be "atmel,hlcdc-display-controller"
+ - pinctrl-names: the pin control state names. Should contain "default".
+ - pinctrl-0: should contain the default pinctrl states.
+ - #address-cells: should be set to 1.
+ - #size-cells: should be set to 0.
+
+Required children nodes:
+ Children nodes are encoding available output ports and their connections
+ to external devices using the OF graph reprensentation (see ../graph.txt).
+ At least one port node is required.
+
+Example:
+
+ hlcdc: hlcdc@f0030000 {
+ compatible = "atmel,sama5d3-hlcdc";
+ reg = <0xf0030000 0x2000>;
+ interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk","sys_clk", "slow_clk";
+ status = "disabled";
+
+ hlcdc-display-controller {
+ compatible = "atmel,hlcdc-display-controller";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ hlcdc_panel_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+
+ hlcdc_pwm: hlcdc-pwm {
+ compatible = "atmel,hlcdc-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwm>;
+ #pwm-cells = <3>;
+ };
+ };
--- /dev/null
+Analog Device ADV7123 Video DAC
+-------------------------------
+
+The ADV7123 is a digital-to-analog converter that outputs VGA signals from a
+parallel video input.
+
+Required properties:
+
+- compatible: Should be "adi,adv7123"
+
+Optional properties:
+
+- psave-gpios: Power save control GPIO
+
+Required nodes:
+
+The ADV7123 has two video ports. Their connections are modeled using the OF
+graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for DPI input
+- Video port 1 for VGA output
+
+
+Example
+-------
+
+ adv7123: encoder@0 {
+ compatible = "adi,adv7123";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ adv7123_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ adv7123_out: endpoint@0 {
+ remote-endpoint = <&vga_connector_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+Analog Device ADV7511(W)/13 HDMI Encoders
+-----------------------------------------
+
+The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters
+compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
+S/PDIF, CEC and HDCP.
+
+Required properties:
+
+- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513"
+- reg: I2C slave address
+
+The ADV7511 supports a large number of input data formats that differ by their
+color depth, color format, clock mode, bit justification and random
+arrangement of components on the data bus. The combination of the following
+properties describe the input and map directly to the video input tables of the
+ADV7511 datasheet that document all the supported combinations.
+
+- adi,input-depth: Number of bits per color component at the input (8, 10 or
+ 12).
+- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
+ "yuv444".
+- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
+ pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
+ data driven on both edges).
+
+The following input format properties are required except in "rgb 1x" and
+"yuv444 1x" modes, in which case they must not be specified.
+
+- adi,input-style: The input components arrangement variant (1, 2 or 3), as
+ listed in the input format tables in the datasheet.
+- adi,input-justification: The input bit justification ("left", "evenly",
+ "right").
+
+Optional properties:
+
+- interrupts: Specifier for the ADV7511 interrupt
+- pd-gpios: Specifier for the GPIO connected to the power down signal
+
+- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
+ (-1200 ps .. 1600 ps). Defaults to no delay.
+- adi,embedded-sync: The input uses synchronization signals embedded in the
+ data stream (similar to BT.656). Defaults to separate H/V synchronization
+ signals.
+
+Required nodes:
+
+The ADV7511 has two video ports. Their connections are modelled using the OF
+graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for the RGB or YUV input
+- Video port 1 for the HDMI output
+
+
+Example
+-------
+
+ adv7511w: hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511w_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+DesignWare HDMI bridge bindings
+
+Required properties:
+- compatible: platform specific such as:
+ * "snps,dw-hdmi-tx"
+ * "fsl,imx6q-hdmi"
+ * "fsl,imx6dl-hdmi"
+ * "rockchip,rk3288-dw-hdmi"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The HDMI interrupt number
+- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
+ as described in Documentation/devicetree/bindings/clock/clock-bindings.txt,
+ the clocks are soc specific, the clock-names should be "iahb", "isfr"
+-port@[X]: SoC specific port nodes with endpoint definitions as defined
+ in Documentation/devicetree/bindings/media/video-interfaces.txt,
+ please refer to the SoC specific binding document:
+ * Documentation/devicetree/bindings/display/imx/hdmi.txt
+ * Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
+
+Optional properties
+- reg-io-width: the width of the reg:1,4, default set to 1 if not present
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
+
+Example:
+ hdmi: hdmi@0120000 {
+ compatible = "fsl,imx6q-hdmi";
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks 123>, <&clks 124>;
+ clock-names = "iahb", "isfr";
+ ddc-i2c-bus = <&i2c2>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
--- /dev/null
+ps8622-bridge bindings
+
+Required properties:
+ - compatible: "parade,ps8622" or "parade,ps8625"
+ - reg: first i2c address of the bridge
+ - sleep-gpios: OF device-tree gpio specification for PD_ pin.
+ - reset-gpios: OF device-tree gpio specification for RST_ pin.
+
+Optional properties:
+ - lane-count: number of DP lanes to use
+ - use-external-pwm: backlight will be controlled by an external PWM
+ - video interfaces: Device node can contain video interface port
+ nodes for panel according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+ lvds-bridge@48 {
+ compatible = "parade,ps8622";
+ reg = <0x48>;
+ sleep-gpios = <&gpc3 6 1 0 0>;
+ reset-gpios = <&gpc3 1 1 0 0>;
+ lane-count = <1>;
+ ports {
+ port@0 {
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+ptn3460 bridge bindings
+
+Required properties:
+ - compatible: "nxp,ptn3460"
+ - reg: i2c address of the bridge
+ - powerdown-gpio: OF device-tree gpio specification for PD_N pin.
+ - reset-gpio: OF device-tree gpio specification for RST_N pin.
+ - edid-emulation: The EDID emulation entry to use
+ +-------+------------+------------------+
+ | Value | Resolution | Description |
+ | 0 | 1024x768 | NXP Generic |
+ | 1 | 1920x1080 | NXP Generic |
+ | 2 | 1920x1080 | NXP Generic |
+ | 3 | 1600x900 | Samsung LTM200KT |
+ | 4 | 1920x1080 | Samsung LTM230HT |
+ | 5 | 1366x768 | NXP Generic |
+ | 6 | 1600x900 | ChiMei M215HGE |
+ +-------+------------+------------------+
+
+ - video interfaces: Device node can contain video interface port
+ nodes for panel according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+ lvds-bridge@20 {
+ compatible = "nxp,ptn3460";
+ reg = <0x20>;
+ powerdown-gpio = <&gpy2 5 1 0 0>;
+ reset-gpio = <&gpx1 5 1 0 0>;
+ edid-emulation = <5>;
+ ports {
+ port@0 {
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+Device-Tree bindings for the NXP TDA998x HDMI transmitter
+
+Required properties;
+ - compatible: must be "nxp,tda998x"
+
+ - reg: I2C address
+
+Optional properties:
+ - interrupts: interrupt number and trigger type
+ default: polling
+
+ - pinctrl-0: pin control group to be used for
+ screen plug/unplug interrupt.
+
+ - pinctrl-names: must contain a "default" entry.
+
+ - video-ports: 24 bits value which defines how the video controller
+ output is wired to the TDA998x input - default: <0x230145>
+
+Example:
+
+ tda998x: hdmi-encoder {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 2>; /* falling edge */
+ pinctrl-0 = <&pmx_camera>;
+ pinctrl-names = "default";
+ };
--- /dev/null
+THine Electronics THC63LVDM83D LVDS serializer
+----------------------------------------------
+
+The THC63LVDM83D is an LVDS serializer designed to support pixel data
+transmission between a host and a flat panel.
+
+Required properties:
+
+- compatible: Should be "thine,thc63lvdm83d"
+
+Optional properties:
+
+- pwdn-gpios: Power down control GPIO
+
+Required nodes:
+
+The THC63LVDM83D has two video ports. Their connections are modeled using the
+OFgraph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for CMOS/TTL input
+- Video port 1 for LVDS output
+
+
+Example
+-------
+
+ lvds_enc: encoder@0 {
+ compatible = "thine,thc63lvdm83d";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lvds_enc_in: endpoint@0 {
+ remote-endpoint = <&rgb_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lvds_enc_out: endpoint@0 {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+* Currus Logic CLPS711X Framebuffer
+
+Required properties:
+- compatible: Shall contain "cirrus,clps711x-fb".
+- reg : Physical base address and length of the controller's registers +
+ location and size of the framebuffer memory.
+- clocks : phandle + clock specifier pair of the FB reference clock.
+- display : phandle to a display node as described in
+ Documentation/devicetree/bindings/display/display-timing.txt.
+ Additionally, the display node has to define properties:
+ - bits-per-pixel: Bits per pixel.
+ - ac-prescale : LCD AC bias frequency. This frequency is the required
+ AC bias frequency for a given manufacturer's LCD plate.
+ - cmap-invert : Invert the color levels (Optional).
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+
+Example:
+ fb: fb@800002c0 {
+ compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb";
+ reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
+ clocks = <&clks 2>;
+ lcd-supply = <®5v0>;
+ display = <&display>;
+ };
+
+ display: display {
+ model = "320x240x4";
+ native-mode = <&timing0>;
+ bits-per-pixel = <4>;
+ ac-prescale = <17>;
+
+ display-timings {
+ timing0: 320x240 {
+ hactive = <320>;
+ hback-porch = <0>;
+ hfront-porch = <0>;
+ hsync-len = <0>;
+ vactive = <240>;
+ vback-porch = <0>;
+ vfront-porch = <0>;
+ vsync-len = <0>;
+ clock-frequency = <6500000>;
+ };
+ };
+ };
--- /dev/null
+Analog TV Connector
+===================
+
+Required properties:
+- compatible: "composite-video-connector" or "svideo-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+
+Required nodes:
+- Video port for TV input
+
+Example
+-------
+
+tv: connector {
+ compatible = "composite-video-connector";
+ label = "tv";
+
+ port {
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
+};
--- /dev/null
+DVI Connector
+==============
+
+Required properties:
+- compatible: "dvi-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+- ddc-i2c-bus: phandle to the i2c bus that is connected to DVI DDC
+- analog: the connector has DVI analog pins
+- digital: the connector has DVI digital pins
+- dual-link: the connector has pins for DVI dual-link
+
+Required nodes:
+- Video port for DVI input
+
+Note: One (or both) of 'analog' or 'digital' must be set.
+
+Example
+-------
+
+dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ digital;
+
+ ddc-i2c-bus = <&i2c3>;
+
+ port {
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+};
--- /dev/null
+HDMI Connector
+==============
+
+Required properties:
+- compatible: "hdmi-connector"
+- type: the HDMI connector type: "a", "b", "c", "d" or "e"
+
+Optional properties:
+- label: a symbolic name for the connector
+- hpd-gpios: HPD GPIO number
+
+Required nodes:
+- Video port for HDMI input
+
+Example
+-------
+
+hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+};
--- /dev/null
+VGA Connector
+=============
+
+Required properties:
+
+- compatible: "vga-connector"
+
+Optional properties:
+
+- label: a symbolic name for the connector corresponding to a hardware label
+- ddc-i2c-bus: phandle to the I2C bus that is connected to VGA DDC
+
+Required nodes:
+
+The VGA connector internal connections are modeled using the OF graph bindings
+specified in Documentation/devicetree/bindings/graph.txt.
+
+The VGA connector has a single port that must be connected to a video source
+port.
+
+
+Example
+-------
+
+vga0: connector@0 {
+ compatible = "vga-connector";
+ label = "vga";
+
+ ddc-i2c-bus = <&i2c3>;
+
+ port {
+ vga_connector_in: endpoint {
+ remote-endpoint = <&adv7123_out>;
+ };
+ };
+};
--- /dev/null
+Device-Tree bindings for Samsung Exynos SoC mobile image compressor (MIC)
+
+MIC (mobile image compressor) resides between decon and mipi dsi. Mipi dsi is
+not capable to transfer high resoltuion frame data as decon can send. MIC
+solves this problem by compressing the frame data by 1/2 before it is
+transferred through mipi dsi. The compressed frame data must be uncompressed in
+the panel PCB.
+
+Required properties:
+- compatible: value should be "samsung,exynos5433-mic".
+- reg: physical base address and length of the MIC registers set and system
+ register of mic.
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+- clock-names: list of clock names sorted in the same order as the clocks
+ property. Must contain "pclk_mic0", "sclk_rgb_vclk_to_mic0".
+- samsung,disp-syscon: the reference node for syscon for DISP block.
+- ports: contains a port which is connected to decon node and dsi node.
+ address-cells and size-cells must 1 and 0, respectively.
+- port: contains an endpoint node which is connected to the endpoint in the
+ decon node or dsi node. The reg value must be 0 and 1 respectively.
+
+Example:
+SoC specific DT entry:
+mic: mic@13930000 {
+ compatible = "samsung,exynos5433-mic";
+ reg = <0x13930000 0x48>;
+ clocks = <&cmu_disp CLK_PCLK_MIC0>,
+ <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
+ clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
+ samsung,disp-syscon = <&syscon_disp>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mic_to_decon: endpoint {
+ remote-endpoint = <&decon_to_mic>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mic_to_dsi: endpoint {
+ remote-endpoint = <&dsi_to_mic>;
+ };
+ };
+ };
+};
--- /dev/null
+Device-Tree bindings for Samsung Exynos SoC display controller (DECON)
+
+DECON (Display and Enhancement Controller) is the Display Controller for the
+Exynos series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be "samsung,exynos5433-decon";
+- reg: physical base address and length of the DECON registers set.
+- interrupts: should contain a list of all DECON IP block interrupts in the
+ order: VSYNC, LCD_SYSTEM. The interrupt specifier format
+ depends on the interrupt controller used.
+- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys"
+ in the same order as they were listed in the interrupts
+ property.
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+- clock-names: list of clock names sorted in the same order as the clocks
+ property. Must contain "aclk_decon", "aclk_smmu_decon0x",
+ "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk",
+ "sclk_decon_eclk"
+- ports: contains a port which is connected to mic node. address-cells and
+ size-cells must 1 and 0, respectively.
+- port: contains an endpoint node which is connected to the endpoint in the mic
+ node. The reg value muset be 0.
+- i80-if-timings: specify whether the panel which is connected to decon uses
+ i80 lcd interface or mipi video interface. This node contains
+ no timing information as that of fimd does. Because there is
+ no register in decon to specify i80 interface timing value,
+ it is not needed, but make it remain to use same kind of node
+ in fimd and exynos7 decon.
+
+Example:
+SoC specific DT entry:
+decon: decon@13800000 {
+ compatible = "samsung,exynos5433-decon";
+ reg = <0x13800000 0x2104>;
+ clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
+ <&cmu_disp CLK_ACLK_XIU_DECON0X>,
+ <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
+ <&cmu_disp CLK_SCLK_DECON_VCLK>,
+ <&cmu_disp CLK_SCLK_DECON_ECLK>;
+ clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x",
+ "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk";
+ interrupt-names = "vsync", "lcd_sys";
+ interrupts = <0 202 0>, <0 203 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ decon_to_mic: endpoint {
+ remote-endpoint = <&mic_to_decon>;
+ };
+ };
+ };
+};
+
+Board specific DT entry:
+&decon {
+ i80-if-timings {
+ };
+};
--- /dev/null
+Device-Tree bindings for Samsung Exynos7 SoC display controller (DECON)
+
+DECON (Display and Enhancement Controller) is the Display Controller for the
+Exynos7 series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be "samsung,exynos7-decon";
+
+- reg: physical base address and length of the DECON registers set.
+
+- interrupt-parent: should be the phandle of the decon controller's
+ parent interrupt controller.
+
+- interrupts: should contain a list of all DECON IP block interrupts in the
+ order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+ format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+ "lcd_sys", in the same order as they were listed in the interrupts
+ property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+ property. Must contain "pclk_decon0", "aclk_decon0",
+ "decon0_eclk", "decon0_vclk".
+- i80-if-timings: timing configuration for lcd i80 interface support.
+
+Optional Properties:
+- samsung,power-domain: a phandle to DECON power domain node.
+- display-timings: timing settings for DECON, as described in document [1].
+ Can be used in case timings cannot be provided otherwise
+ or to override timings provided by the panel.
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+
+Example:
+
+SoC specific DT entry:
+
+ decon@13930000 {
+ compatible = "samsung,exynos7-decon";
+ interrupt-parent = <&combiner>;
+ reg = <0x13930000 0x1000>;
+ interrupt-names = "lcd_sys", "vsync", "fifo";
+ interrupts = <0 188 0>, <0 189 0>, <0 190 0>;
+ clocks = <&clock_disp PCLK_DECON_INT>,
+ <&clock_disp ACLK_DECON_INT>,
+ <&clock_disp SCLK_DECON_INT_ECLK>,
+ <&clock_disp SCLK_DECON_INT_EXTCLKPLL>;
+ clock-names = "pclk_decon0", "aclk_decon0", "decon0_eclk",
+ "decon0_vclk";
+ status = "disabled";
+ };
+
+Board specific DT entry:
+
+ decon@13930000 {
+ pinctrl-0 = <&lcd_clk &pwm1_out>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
--- /dev/null
+The Exynos display port interface should be configured based on
+the type of panel connected to it.
+
+We use two nodes:
+ -dp-controller node
+ -dptx-phy node(defined inside dp-controller node)
+
+For the DP-PHY initialization, we use the dptx-phy node.
+Required properties for dptx-phy: deprecated, use phys and phy-names
+ -reg: deprecated
+ Base address of DP PHY register.
+ -samsung,enable-mask: deprecated
+ The bit-mask used to enable/disable DP PHY.
+
+For the Panel initialization, we read data from dp-controller node.
+Required properties for dp-controller:
+ -compatible:
+ should be "samsung,exynos5-dp".
+ -reg:
+ physical base address of the controller and length
+ of memory mapped region.
+ -interrupts:
+ interrupt combiner values.
+ -clocks:
+ from common clock binding: handle to dp clock.
+ -clock-names:
+ from common clock binding: Shall be "dp".
+ -interrupt-parent:
+ phandle to Interrupt combiner node.
+ -phys:
+ from general PHY binding: the phandle for the PHY device.
+ -phy-names:
+ from general PHY binding: Should be "dp".
+ -samsung,color-space:
+ input video data format.
+ COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
+ -samsung,dynamic-range:
+ dynamic range for input video data.
+ VESA = 0, CEA = 1
+ -samsung,ycbcr-coeff:
+ YCbCr co-efficients for input video.
+ COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
+ -samsung,color-depth:
+ number of bits per colour component.
+ COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
+ -samsung,link-rate:
+ link rate supported by the panel.
+ LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
+ -samsung,lane-count:
+ number of lanes supported by the panel.
+ LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
+ - display-timings: timings for the connected panel as described by
+ Documentation/devicetree/bindings/display/display-timing.txt
+
+Optional properties for dp-controller:
+ -interlaced:
+ interlace scan mode.
+ Progressive if defined, Interlaced if not defined
+ -vsync-active-high:
+ VSYNC polarity configuration.
+ High if defined, Low if not defined
+ -hsync-active-high:
+ HSYNC polarity configuration.
+ High if defined, Low if not defined
+ -samsung,hpd-gpio:
+ Hotplug detect GPIO.
+ Indicates which GPIO should be used for hotplug
+ detection
+ -video interfaces: Device node can contain video interface port
+ nodes according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SOC specific portion:
+ dp-controller {
+ compatible = "samsung,exynos5-dp";
+ reg = <0x145b0000 0x10000>;
+ interrupts = <10 3>;
+ interrupt-parent = <&combiner>;
+ clocks = <&clock 342>;
+ clock-names = "dp";
+
+ phys = <&dp_phy>;
+ phy-names = "dp";
+ };
+
+Board Specific portion:
+ dp-controller {
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <4>;
+
+ display-timings {
+ native-mode = <&lcd_timing>;
+ lcd_timing: 1366x768 {
+ clock-frequency = <70589280>;
+ hactive = <1366>;
+ vactive = <768>;
+ hfront-porch = <40>;
+ hback-porch = <40>;
+ hsync-len = <32>;
+ vback-porch = <10>;
+ vfront-porch = <12>;
+ vsync-len = <6>;
+ };
+ };
+
+ ports {
+ port@0 {
+ dp_out: endpoint {
+ remote-endpoint = <&bridge_in>;
+ };
+ };
+ };
+ };
--- /dev/null
+Exynos MIPI DSI Master
+
+Required properties:
+ - compatible: value should be one of the following
+ "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */
+ "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */
+ "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */
+ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */
+ "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */
+ - reg: physical base address and length of the registers set for the device
+ - interrupts: should contain DSI interrupt
+ - clocks: list of clock specifiers, must contain an entry for each required
+ entry in clock-names
+ - clock-names: should include "bus_clk"and "sclk_mipi" entries
+ the use of "pll_clk" is deprecated
+ - phys: list of phy specifiers, must contain an entry for each required
+ entry in phy-names
+ - phy-names: should include "dsim" entry
+ - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
+ - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
+ - samsung,pll-clock-frequency: specifies frequency of the oscillator clock
+ - #address-cells, #size-cells: should be set respectively to <1> and <0>
+ according to DSI host bindings (see MIPI DSI bindings [1])
+
+Optional properties:
+ - power-domains: a phandle to DSIM power domain node
+
+Child nodes:
+ Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
+
+Video interfaces:
+ Device node can contain video interface port nodes according to [2].
+ The following are properties specific to those nodes:
+
+ port node inbound:
+ - reg: (required) must be 0.
+ port node outbound:
+ - reg: (required) must be 1.
+
+ endpoint node connected from mic node (reg = 0):
+ - remote-endpoint: specifies the endpoint in mic node. This node is required
+ for Exynos5433 mipi dsi. So mic can access to panel node
+ thoughout this dsi node.
+ endpoint node connected to panel node (reg = 1):
+ - remote-endpoint: specifies the endpoint in panel node. This node is
+ required in all kinds of exynos mipi dsi to represent
+ the connection between mipi dsi and panel.
+ - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
+ mode
+ - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
+
+[1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ dsi@11C80000 {
+ compatible = "samsung,exynos4210-mipi-dsi";
+ reg = <0x11C80000 0x10000>;
+ interrupts = <0 79 0>;
+ clocks = <&clock 286>, <&clock 143>;
+ clock-names = "bus_clk", "sclk_mipi";
+ phys = <&mipi_phy 1>;
+ phy-names = "dsim";
+ vddcore-supply = <&vusb_reg>;
+ vddio-supply = <&vmipi_reg>;
+ power-domains = <&pd_lcd0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,pll-clock-frequency = <24000000>;
+
+ panel@1 {
+ reg = <0>;
+ ...
+ port {
+ panel_ep: endpoint {
+ remote-endpoint = <&dsi_ep>;
+ };
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ decon_to_mic: endpoint {
+ remote-endpoint = <&mic_to_decon>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi_ep: endpoint {
+ reg = <0>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ remote-endpoint = <&panel_ep>;
+ };
+ };
+ };
+ };
--- /dev/null
+Device-Tree bindings for drm hdmi driver
+
+Required properties:
+- compatible: value should be one among the following:
+ 1) "samsung,exynos5-hdmi" <DEPRECATED>
+ 2) "samsung,exynos4210-hdmi"
+ 3) "samsung,exynos4212-hdmi"
+ 4) "samsung,exynos5420-hdmi"
+- reg: physical base address of the hdmi and length of memory mapped
+ region.
+- interrupts: interrupt number to the cpu.
+- hpd-gpio: following information about the hotplug gpio pin.
+ a) phandle of the gpio controller node.
+ b) pin number within the gpio controller.
+ c) optional flags and pull up/down.
+- clocks: list of clock IDs from SoC clock driver.
+ a) hdmi: Gate of HDMI IP bus clock.
+ b) sclk_hdmi: Gate of HDMI special clock.
+ c) sclk_pixel: Pixel special clock, one of the two possible inputs of
+ HDMI clock mux.
+ d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
+ HDMI clock mux.
+ e) mout_hdmi: It is required by the driver to switch between the 2
+ parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
+ after configuration, parent is set to sclk_hdmiphy else
+ sclk_pixel.
+- clock-names: aliases as per driver requirements for above clock IDs:
+ "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
+- ddc: phandle to the hdmi ddc node
+- phy: phandle to the hdmi phy node
+- samsung,syscon-phandle: phandle for system controller node for PMU.
+
+Example:
+
+ hdmi {
+ compatible = "samsung,exynos4212-hdmi";
+ reg = <0x14530000 0x100000>;
+ interrupts = <0 95 0>;
+ hpd-gpio = <&gpx3 7 1>;
+ ddc = <&hdmi_ddc_node>;
+ phy = <&hdmi_phy_node>;
+ samsung,syscon-phandle = <&pmu_system_controller>;
+ };
--- /dev/null
+Device-Tree bindings for hdmiddc driver
+
+Required properties:
+- compatible: value should be one of the following
+ 1) "samsung,exynos5-hdmiddc" <DEPRECATED>
+ 2) "samsung,exynos4210-hdmiddc"
+
+- reg: I2C address of the hdmiddc device.
+
+Example:
+
+ hdmiddc {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
--- /dev/null
+Device-Tree bindings for hdmiphy driver
+
+Required properties:
+- compatible: value should be one of the following:
+ 1) "samsung,exynos5-hdmiphy" <DEPRECATED>
+ 2) "samsung,exynos4210-hdmiphy".
+ 3) "samsung,exynos4212-hdmiphy".
+- reg: I2C address of the hdmiphy device.
+
+Example:
+
+ hdmiphy {
+ compatible = "samsung,exynos4210-hdmiphy";
+ reg = <0x38>;
+ };
--- /dev/null
+Device-Tree bindings for mixer driver
+
+Required properties:
+- compatible: value should be one of the following:
+ 1) "samsung,exynos5-mixer" <DEPRECATED>
+ 2) "samsung,exynos4210-mixer"
+ 3) "samsung,exynos4212-mixer"
+ 4) "samsung,exynos5250-mixer"
+ 5) "samsung,exynos5420-mixer"
+
+- reg: physical base address of the mixer and length of memory mapped
+ region.
+- interrupts: interrupt number to the cpu.
+- clocks: list of clock IDs from SoC clock driver.
+ a) mixer: Gate of Mixer IP bus clock.
+ b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
+ mixer mux.
+ c) hdmi: Gate of HDMI IP bus clock, needed together with sclk_hdmi.
+
+Example:
+
+ mixer {
+ compatible = "samsung,exynos5250-mixer";
+ reg = <0x14450000 0x10000>;
+ interrupts = <0 94 0>;
+ };
--- /dev/null
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+ "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+ "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+ "samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+ "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
+ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+ "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
+ "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupt-parent: should be the phandle of the fimd controller's
+ parent interrupt controller.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+ order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+ format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+ "lcd_sys", in the same order as they were listed in the interrupts
+ property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+ property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- power-domains: a phandle to FIMD power domain node.
+- samsung,invert-vden: video enable signal is inverted
+- samsung,invert-vclk: video clock signal is inverted
+- display-timings: timing settings for FIMD, as described in document [1].
+ Can be used in case timings cannot be provided otherwise
+ or to override timings provided by the panel.
+- samsung,sysreg: handle to syscon used to control the system registers
+- i80-if-timings: timing configuration for lcd i80 interface support.
+ - cs-setup: clock cycles for the active period of address signal is enabled
+ until chip select is enabled.
+ If not specified, the default value(0) will be used.
+ - wr-setup: clock cycles for the active period of CS signal is enabled until
+ write signal is enabled.
+ If not specified, the default value(0) will be used.
+ - wr-active: clock cycles for the active period of CS is enabled.
+ If not specified, the default value(1) will be used.
+ - wr-hold: clock cycles for the active period of CS is disabled until write
+ signal is disabled.
+ If not specified, the default value(0) will be used.
+
+ The parameters are defined as:
+
+ VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
+ : : : : :
+ Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+ | cs-setup+1 | : : :
+ |<---------->| : : :
+ Chip Select ???????????????|____________:____________:____________|??
+ | wr-setup+1 | | wr-hold+1 |
+ |<---------->| |<---------->|
+ Write Enable ????????????????????????????|____________|???????????????
+ | wr-active+1|
+ |<---------->|
+ Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
+
+The device node can contain 'port' child nodes according to the bindings defined
+in [2]. The following are properties specific to those nodes:
+- reg: (required) port index, can be:
+ 0 - for CAMIF0 input,
+ 1 - for CAMIF1 input,
+ 2 - for CAMIF2 input,
+ 3 - for parallel output,
+ 4 - for write-back interface
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SoC specific DT entry:
+
+ fimd@11c00000 {
+ compatible = "samsung,exynos4210-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x11c00000 0x20000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <11 0>, <11 1>, <11 2>;
+ clocks = <&clock 140>, <&clock 283>;
+ clock-names = "sclk_fimd", "fimd";
+ power-domains = <&pd_lcd0>;
+ status = "disabled";
+ };
+
+Board specific DT entry:
+
+ fimd@11c00000 {
+ pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
--- /dev/null
+Device Tree bindings for Freescale DCU DRM Driver
+
+Required properties:
+- compatible: Should be one of
+ * "fsl,ls1021a-dcu".
+ * "fsl,vf610-dcu".
+
+- reg: Address and length of the register set for dcu.
+- clocks: From common clock binding: handle to dcu clock.
+- clock-names: From common clock binding: Shall be "dcu".
+- big-endian Boolean property, LS1021A DCU registers are big-endian.
+- fsl,panel: The phandle to panel node.
+
+Examples:
+dcu: dcu@2ce0000 {
+ compatible = "fsl,ls1021a-dcu";
+ reg = <0x0 0x2ce0000 0x0 0x10000>;
+ clocks = <&platform_clk 0>;
+ clock-names = "dcu";
+ big-endian;
+ fsl,panel = <&panel>;
+};
--- /dev/null
+Freescale imx21 Framebuffer
+
+This framebuffer driver supports devices imx1, imx21, imx25, and imx27.
+
+Required properties:
+- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : One interrupt of the fb dev
+
+Required nodes:
+- display: Phandle to a display node as described in
+ Documentation/devicetree/bindings/display/display-timing.txt
+ Additional, the display node has to define properties:
+ - bits-per-pixel: Bits per pixel
+ - fsl,pcr: LCDC PCR value
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+- fsl,dmacr: DMA Control Register value. This is optional. By default, the
+ register is not modified as recommended by the datasheet.
+- fsl,lpccr: Contrast Control Register value. This property provides the
+ default value for the contrast control register.
+ If that property is omitted, the register is zeroed.
+- fsl,lscr1: LCDC Sharp Configuration Register value.
+
+Example:
+
+ imxfb: fb@10021000 {
+ compatible = "fsl,imx21-fb";
+ interrupts = <61>;
+ reg = <0x10021000 0x1000>;
+ display = <&display0>;
+ };
+
+ ...
+
+ display0: display0 {
+ model = "Primeview-PD050VL1";
+ native-mode = <&timing_disp0>;
+ bits-per-pixel = <16>;
+ fsl,pcr = <0xf0c88080>; /* non-standard but required */
+ display-timings {
+ timing_disp0: 640x480 {
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <112>;
+ hfront-porch = <36>;
+ hsync-len = <32>;
+ vback-porch = <33>;
+ vfront-porch = <33>;
+ vsync-len = <2>;
+ clock-frequency = <25000000>;
+ };
+ };
+ };
--- /dev/null
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+ of IPU devices
+
+example:
+
+display-subsystem {
+ compatible = "fsl,display-subsystem";
+ ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu"
+- reg: should be register base and length as documented in the
+ datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+ in this order.
+- resets: phandle pointing to the system reset controller and
+ reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ Ports 0 and 1 should correspond to CSI0 and CSI1,
+ ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx53-ipu";
+ reg = <0x18000000 0x080000000>;
+ interrupts = <11 10>;
+ resets = <&src 2>;
+
+ ipu_di0: port@2 {
+ reg = <2>;
+
+ ipu_di0_disp0: endpoint {
+ remote-endpoint = <&display_in>;
+ };
+ };
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+ display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+ and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+ channel
+- port@[0-1]: Port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ Port 0 is the input port connected to the IPU display interface,
+ port 1 is the output port connected to a panel.
+
+example:
+
+display@di0 {
+ compatible = "fsl,imx-parallel-display";
+ edid = [edid-data];
+ interface-pix-fmt = "rgb24";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
+panel {
+ ...
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+};
--- /dev/null
+Device-Tree bindings for HDMI Transmitter
+
+HDMI Transmitter
+================
+
+The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with accompanying PHY IP.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+ - gpr : should be <&gpr>.
+ The phandle points to the iomuxc-gpr region containing the HDMI
+ multiplexer control register.
+ - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
+ in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+ Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+ - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt,
+ corresponding to the four inputs to the HDMI multiplexer.
+
+Optional properties:
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+
+example:
+
+ gpr: iomuxc-gpr@020e0000 {
+ /* ... */
+ };
+
+ hdmi: hdmi@0120000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-hdmi";
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks 123>, <&clks 124>;
+ clock-names = "iahb", "isfr";
+ ddc-i2c-bus = <&i2c2>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
--- /dev/null
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+ Both LDB versions are similar, but i.MX6 has an additional
+ multiplexer in the front to select any of the four IPU display
+ interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+ The phandle points to the iomuxc-gpr region containing the LVDS
+ control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+ the display interface selector clocks, as described in
+ Documentation/devicetree/bindings/clock/clock-bindings.txt
+ The following clocks are expected on i.MX53:
+ "di0_pll" - LDB LVDS channel 0 mux
+ "di1_pll" - LDB LVDS channel 1 mux
+ "di0" - LDB LVDS channel 0 gate
+ "di1" - LDB LVDS channel 1 gate
+ "di0_sel" - IPU1 DI0 mux
+ "di1_sel" - IPU1 DI1 mux
+ On i.MX6q the following additional clocks are needed:
+ "di2_sel" - IPU2 DI0 mux
+ "di3_sel" - IPU2 DI1 mux
+ The needed clock numbers for each are documented in
+ Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
+ Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+ not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+ be configured - one input will be distributed on both outputs in dual
+ channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/graph.txt.
+ On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+ limitations, only one input port (port@[0,1]) can be used for each channel
+ (lvds-channel@[0,1], respectively).
+ On i.MX6, there should be four input ports (port@[0-3]) that correspond
+ to the four LVDS multiplexer inputs.
+ A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+ to a panel input port. Optionally, the output port can be left out if
+ display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - display-timings : A node that describes the display timings as defined in
+ Documentation/devicetree/bindings/display/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+ This describes how the color bits are laid out in the
+ serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+ /* ... */
+};
+
+ldb: ldb@53fa8008 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx53-ldb";
+ gpr = <&gpr>;
+ clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+ <&clks IMX5_CLK_LDB_DI1_SEL>,
+ <&clks IMX5_CLK_IPU_DI0_SEL>,
+ <&clks IMX5_CLK_IPU_DI1_SEL>,
+ <&clks IMX5_CLK_LDB_DI0_GATE>,
+ <&clks IMX5_CLK_LDB_DI1_GATE>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel",
+ "di0", "di1";
+
+ /* Using an of-graph endpoint link to connect the panel */
+ lvds-channel@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu_di0_lvds0>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ /* Using display-timings and fsl,data-mapping/width instead */
+ lvds-channel@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+
+ display-timings {
+ /* ... */
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lvds1_in: endpoint {
+ remote-endpoint = <&ipu_di1_lvds1>;
+ };
+ };
+ };
+};
+
+panel: lvds-panel {
+ /* ... */
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+};
--- /dev/null
+MIPI DSI (Display Serial Interface) busses
+==========================================
+
+The MIPI Display Serial Interface specifies a serial bus and a protocol for
+communication between a host and up to four peripherals. This document will
+define the syntax used to represent a DSI bus in a device tree.
+
+This document describes DSI bus-specific properties only or defines existing
+standard properties in the context of the DSI bus.
+
+Each DSI host provides a DSI bus. The DSI host controller's node contains a
+set of properties that characterize the bus. Child nodes describe individual
+peripherals on that bus.
+
+The following assumes that only a single peripheral is connected to a DSI
+host. Experience shows that this is true for the large majority of setups.
+
+DSI host
+--------
+
+In addition to the standard properties and those defined by the parent bus of
+a DSI host, the following properties apply to a node representing a DSI host.
+
+Required properties:
+- #address-cells: The number of cells required to represent an address on the
+ bus. DSI peripherals are addressed using a 2-bit virtual channel number, so
+ a maximum of 4 devices can be addressed on a single bus. Hence the value of
+ this property should be 1.
+- #size-cells: Should be 0. There are cases where it makes sense to use a
+ different value here. See below.
+
+DSI peripheral
+--------------
+
+Peripherals are represented as child nodes of the DSI host's node. Properties
+described here apply to all DSI peripherals, but individual bindings may want
+to define additional, device-specific properties.
+
+Required properties:
+- reg: The virtual channel number of a DSI peripheral. Must be in the range
+ from 0 to 3.
+
+Some DSI peripherals respond to more than a single virtual channel. In that
+case two alternative representations can be chosen:
+- The reg property can take multiple entries, one for each virtual channel
+ that the peripheral responds to.
+- If the virtual channels that a peripheral responds to are consecutive, the
+ #size-cells can be set to 1. The first cell of each entry in the reg
+ property is the number of the first virtual channel and the second cell is
+ the number of consecutive virtual channels.
+
+Example
+-------
+
+ dsi-host {
+ ...
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* peripheral responds to virtual channel 0 */
+ peripheral@0 {
+ compatible = "...";
+ reg = <0>;
+ };
+
+ ...
+ };
+
+ dsi-host {
+ ...
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* peripheral responds to virtual channels 0 and 2 */
+ peripheral@0 {
+ compatible = "...";
+ reg = <0, 2>;
+ };
+
+ ...
+ };
+
+ dsi-host {
+ ...
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* peripheral responds to virtual channels 1, 2 and 3 */
+ peripheral@1 {
+ compatible = "...";
+ reg = <1 3>;
+ };
+
+ ...
+ };
--- /dev/null
+Qualcomm Technologies Inc. adreno/snapdragon DSI output
+
+DSI Controller:
+Required properties:
+- compatible:
+ * "qcom,mdss-dsi-ctrl"
+- reg: Physical base address and length of the registers of controller
+- reg-names: The names of register regions. The following regions are required:
+ * "dsi_ctrl"
+- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should
+ be 0 or 1, since we have 2 DSI controllers at most for now.
+- interrupts: The interrupt signal from the DSI block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+ See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "bus_clk"
+ * "byte_clk"
+ * "core_clk"
+ * "core_mmss_clk"
+ * "iface_clk"
+ * "mdp_core_clk"
+ * "pixel_clk"
+- vdd-supply: phandle to vdd regulator device node
+- vddio-supply: phandle to vdd-io regulator device node
+- vdda-supply: phandle to vdda regulator device node
+- qcom,dsi-phy: phandle to DSI PHY device node
+
+Optional properties:
+- panel@0: Node of panel connected to this DSI controller.
+ See files in Documentation/devicetree/bindings/display/panel/ for each supported
+ panel.
+- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
+ driving a panel which needs 2 DSI links.
+- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
+ the master link of the 2-DSI panel.
+- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
+ driving a 2-DSI panel whose 2 links need receive command simultaneously.
+- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
+ through MDP block
+- pinctrl-names: the pin control state names; should contain "default"
+- pinctrl-0: the default pinctrl state (active)
+- pinctrl-n: the "sleep" pinctrl state
+- port: DSI controller output port. This contains one endpoint subnode, with its
+ remote-endpoint set to the phandle of the connected panel's endpoint.
+ See Documentation/devicetree/bindings/graph.txt for device graph info.
+
+DSI PHY:
+Required properties:
+- compatible: Could be the following
+ * "qcom,dsi-phy-28nm-hpm"
+ * "qcom,dsi-phy-28nm-lp"
+ * "qcom,dsi-phy-20nm"
+- reg: Physical base address and length of the registers of PLL, PHY and PHY
+ regulator
+- reg-names: The names of register regions. The following regions are required:
+ * "dsi_pll"
+ * "dsi_phy"
+ * "dsi_phy_regulator"
+- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should
+ be 0 or 1, since we have 2 DSI PHYs at most for now.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+ See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "iface_clk"
+- vddio-supply: phandle to vdd-io regulator device node
+
+Optional properties:
+- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
+ regulator is wanted.
+
+Example:
+ mdss_dsi0: qcom,mdss_dsi@fd922800 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ qcom,dsi-host-index = <0>;
+ interrupt-parent = <&mdss_mdp>;
+ interrupts = <4 0>;
+ reg-names = "dsi_ctrl";
+ reg = <0xfd922800 0x200>;
+ power-domains = <&mmcc MDSS_GDSC>;
+ clock-names =
+ "bus_clk",
+ "byte_clk",
+ "core_clk",
+ "core_mmss_clk",
+ "iface_clk",
+ "mdp_core_clk",
+ "pixel_clk";
+ clocks =
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_BYTE0_CLK>,
+ <&mmcc MDSS_ESC0_CLK>,
+ <&mmcc MMSS_MISC_AHB_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_PCLK0_CLK>;
+ vdda-supply = <&pma8084_l2>;
+ vdd-supply = <&pma8084_l22>;
+ vddio-supply = <&pma8084_l12>;
+
+ qcom,dsi-phy = <&mdss_dsi_phy0>;
+
+ qcom,dual-dsi-mode;
+ qcom,master-dsi;
+ qcom,sync-dual-dsi;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mdss_dsi_active>;
+ pinctrl-1 = <&mdss_dsi_suspend>;
+
+ panel: panel@0 {
+ compatible = "sharp,lq101r1sx01";
+ reg = <0>;
+ link2 = <&secondary>;
+
+ power-supply = <...>;
+ backlight = <...>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+
+ port {
+ dsi0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 {
+ compatible = "qcom,dsi-phy-28nm-hpm";
+ qcom,dsi-phy-index = <0>;
+ reg-names =
+ "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x2b0>,
+ <0xfd922d80 0x7b>;
+ clock-names = "iface_clk";
+ clocks = <&mmcc MDSS_AHB_CLK>;
+ vddio-supply = <&pma8084_l12>;
+
+ qcom,dsi-phy-regulator-ldo-mode;
+ };
--- /dev/null
+Qualcomm Technologies Inc. adreno/snapdragon eDP output
+
+Required properties:
+- compatible:
+ * "qcom,mdss-edp"
+- reg: Physical base address and length of the registers of controller and PLL
+- reg-names: The names of register regions. The following regions are required:
+ * "edp"
+ * "pll_base"
+- interrupts: The interrupt signal from the eDP block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+ See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "core_clk"
+ * "iface_clk"
+ * "mdp_core_clk"
+ * "pixel_clk"
+ * "link_clk"
+- #clock-cells: The value should be 1.
+- vdda-supply: phandle to vdda regulator device node
+- lvl-vdd-supply: phandle to regulator device node which is used to supply power
+ to HPD receiving chip
+- panel-en-gpios: GPIO pin to supply power to panel.
+- panel-hpd-gpios: GPIO pin used for eDP hpd.
+
+
+Optional properties:
+- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
+ through MDP block
+
+Example:
+ mdss_edp: qcom,mdss_edp@fd923400 {
+ compatible = "qcom,mdss-edp";
+ reg-names =
+ "edp",
+ "pll_base";
+ reg = <0xfd923400 0x700>,
+ <0xfd923a00 0xd4>;
+ interrupt-parent = <&mdss_mdp>;
+ interrupts = <12 0>;
+ power-domains = <&mmcc MDSS_GDSC>;
+ clock-names =
+ "core_clk",
+ "pixel_clk",
+ "iface_clk",
+ "link_clk",
+ "mdp_core_clk";
+ clocks =
+ <&mmcc MDSS_EDPAUX_CLK>,
+ <&mmcc MDSS_EDPPIXEL_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_EDPLINK_CLK>,
+ <&mmcc MDSS_MDP_CLK>;
+ #clock-cells = <1>;
+ vdda-supply = <&pma8084_l12>;
+ lvl-vdd-supply = <&lvl_vreg>;
+ panel-en-gpios = <&tlmm 137 0>;
+ panel-hpd-gpios = <&tlmm 103 0>;
+ };
--- /dev/null
+Qualcomm adreno/snapdragon GPU
+
+Required properties:
+- compatible: "qcom,adreno-3xx"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the gpu.
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "core_clk"
+ * "iface_clk"
+ * "mem_iface_clk"
+- qcom,chipid: gpu chip-id. Note this may become optional for future
+ devices if we can reliably read the chipid from hw
+- qcom,gpu-pwrlevels: list of operating points
+ - compatible: "qcom,gpu-pwrlevels"
+ - for each qcom,gpu-pwrlevel:
+ - qcom,gpu-freq: requested gpu clock speed
+ - NOTE: downstream android driver defines additional parameters to
+ configure memory bandwidth scaling per OPP.
+
+Example:
+
+/ {
+ ...
+
+ gpu: qcom,kgsl-3d0@4300000 {
+ compatible = "qcom,adreno-3xx";
+ reg = <0x04300000 0x20000>;
+ reg-names = "kgsl_3d0_reg_memory";
+ interrupts = <GIC_SPI 80 0>;
+ interrupt-names = "kgsl_3d0_irq";
+ clock-names =
+ "core_clk",
+ "iface_clk",
+ "mem_iface_clk";
+ clocks =
+ <&mmcc GFX3D_CLK>,
+ <&mmcc GFX3D_AHB_CLK>,
+ <&mmcc MMSS_IMEM_AHB_CLK>;
+ qcom,chipid = <0x03020100>;
+ qcom,gpu-pwrlevels {
+ compatible = "qcom,gpu-pwrlevels";
+ qcom,gpu-pwrlevel@0 {
+ qcom,gpu-freq = <450000000>;
+ };
+ qcom,gpu-pwrlevel@1 {
+ qcom,gpu-freq = <27000000>;
+ };
+ };
+ };
+};
--- /dev/null
+Qualcomm adreno/snapdragon hdmi output
+
+Required properties:
+- compatible: one of the following
+ * "qcom,hdmi-tx-8994"
+ * "qcom,hdmi-tx-8084"
+ * "qcom,hdmi-tx-8974"
+ * "qcom,hdmi-tx-8660"
+ * "qcom,hdmi-tx-8960"
+- reg: Physical base address and length of the controller's registers
+- reg-names: "core_physical"
+- interrupts: The interrupt signal from the hdmi block.
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
+- qcom,hdmi-tx-ddc-data-gpio: ddc data pin
+- qcom,hdmi-tx-hpd-gpio: hpd pin
+- core-vdda-supply: phandle to supply regulator
+- hdmi-mux-supply: phandle to mux regulator
+
+Optional properties:
+- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
+- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
+- pinctrl-names: the pin control state names; should contain "default"
+- pinctrl-0: the default pinctrl state (active)
+- pinctrl-1: the "sleep" pinctrl state
+
+Example:
+
+/ {
+ ...
+
+ hdmi: qcom,hdmi-tx-8960@4a00000 {
+ compatible = "qcom,hdmi-tx-8960";
+ reg-names = "core_physical";
+ reg = <0x04a00000 0x1000>;
+ interrupts = <GIC_SPI 79 0>;
+ clock-names =
+ "core_clk",
+ "master_iface_clk",
+ "slave_iface_clk";
+ clocks =
+ <&mmcc HDMI_APP_CLK>,
+ <&mmcc HDMI_M_AHB_CLK>,
+ <&mmcc HDMI_S_AHB_CLK>;
+ qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
+ core-vdda-supply = <&pm8921_hdmi_mvs>;
+ hdmi-mux-supply = <&ext_3p3v>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&hpd_active &ddc_active &cec_active>;
+ pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
+ };
+};
--- /dev/null
+Qualcomm adreno/snapdragon display controller
+
+Required properties:
+- compatible:
+ * "qcom,mdp" - mdp4
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the display controller.
+- connectors: array of phandles for output device(s)
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "core_clk"
+ * "iface_clk"
+ * "lut_clk"
+ * "src_clk"
+ * "hdmi_clk"
+ * "mpd_clk"
+
+Optional properties:
+- gpus: phandle for gpu device
+
+Example:
+
+/ {
+ ...
+
+ mdp: qcom,mdp@5100000 {
+ compatible = "qcom,mdp";
+ reg = <0x05100000 0xf0000>;
+ interrupts = <GIC_SPI 75 0>;
+ connectors = <&hdmi>;
+ gpus = <&gpu>;
+ clock-names =
+ "core_clk",
+ "iface_clk",
+ "lut_clk",
+ "src_clk",
+ "hdmi_clk",
+ "mdp_clk";
+ clocks =
+ <&mmcc MDP_SRC>,
+ <&mmcc MDP_AHB_CLK>,
+ <&mmcc MDP_LUT_CLK>,
+ <&mmcc TV_SRC>,
+ <&mmcc HDMI_TV_CLK>,
+ <&mmcc MDP_TV_CLK>;
+ };
+};
--- /dev/null
+* Freescale MXS LCD Interface (LCDIF)
+
+Required properties:
+- compatible: Should be "fsl,<chip>-lcdif". Supported chips include
+ imx23 and imx28.
+- reg: Address and length of the register set for lcdif
+- interrupts: Should contain lcdif interrupts
+- display : phandle to display node (see below for details)
+
+* display node
+
+Required properties:
+- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
+- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>.
+
+Required sub-node:
+- display-timings : Refer to binding doc display-timing.txt for details.
+
+Examples:
+
+lcdif@80030000 {
+ compatible = "fsl,imx28-lcdif";
+ reg = <0x80030000 2000>;
+ interrupts = <38 86>;
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <164>;
+ hback-porch = <89>;
+ hsync-len = <10>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
--- /dev/null
+Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "ampire,am800480r3tmqwa1h"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 8.0" WUXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b101ean01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 10.1" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b101aw03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 10.1" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b101ean01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 10.1" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b101xtn01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 11.6" HD (1366x768) color TFT-LCD panel
+
+Required properties:
+- compatible: should be "auo,b116xw03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 13.3" FHD (1920x1080) color TFT-LCD panel
+
+Required properties:
+- compatible: should be "auo,b133htn01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+AU Optronics Corporation 13.3" WXGA (1366x768) TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b133xtn01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Shanghai AVIC Optoelectronics 7" 1024x600 color TFT-LCD panel
+
+Required properties:
+- compatible: should be "avic,tm070ddh03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "chunghwa,claa101wa01a"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "chunghwa,claa101wb03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+display-timing bindings
+=======================
+
+display-timings node
+--------------------
+
+required properties:
+ - none
+
+optional properties:
+ - native-mode: The native mode for the display, in case multiple modes are
+ provided. When omitted, assume the first node is the native.
+
+timing subnode
+--------------
+
+required properties:
+ - hactive, vactive: display resolution
+ - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters
+ in pixels
+ vfront-porch, vback-porch, vsync-len: vertical display timing parameters in
+ lines
+ - clock-frequency: display clock in Hz
+
+optional properties:
+ - hsync-active: hsync pulse is active low/high/ignored
+ - vsync-active: vsync pulse is active low/high/ignored
+ - de-active: data-enable pulse is active low/high/ignored
+ - pixelclk-active: with
+ - active high = drive pixel data on rising edge/
+ sample data on falling edge
+ - active low = drive pixel data on falling edge/
+ sample data on rising edge
+ - ignored = ignored
+ - interlaced (bool): boolean to enable interlaced mode
+ - doublescan (bool): boolean to enable doublescan mode
+ - doubleclk (bool): boolean to enable doubleclock mode
+
+All the optional properties that are not bool follow the following logic:
+ <1>: high active
+ <0>: low active
+ omitted: not used on hardware
+
+There are different ways of describing the capabilities of a display. The
+devicetree representation corresponds to the one commonly found in datasheets
+for displays. If a display supports multiple signal timings, the native-mode
+can be specified.
+
+The parameters are defined as:
+
+ +----------+-------------------------------------+----------+-------+
+ | | ↑ | | |
+ | | |vback_porch | | |
+ | | ↓ | | |
+ +----------#######################################----------+-------+
+ | # ↑ # | |
+ | # | # | |
+ | hback # | # hfront | hsync |
+ | porch # | hactive # porch | len |
+ |<-------->#<-------+--------------------------->#<-------->|<----->|
+ | # | # | |
+ | # |vactive # | |
+ | # | # | |
+ | # ↓ # | |
+ +----------#######################################----------+-------+
+ | | ↑ | | |
+ | | |vfront_porch | | |
+ | | ↓ | | |
+ +----------+-------------------------------------+----------+-------+
+ | | ↑ | | |
+ | | |vsync_len | | |
+ | | ↓ | | |
+ +----------+-------------------------------------+----------+-------+
+
+Example:
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 1080p24 {
+ /* 1920x1080p24 */
+ clock-frequency = <52000000>;
+ hactive = <1920>;
+ vactive = <1080>;
+ hfront-porch = <25>;
+ hback-porch = <25>;
+ hsync-len = <25>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ vsync-len = <2>;
+ hsync-active = <1>;
+ };
+ };
+
+Every required property also supports the use of ranges, so the commonly used
+datasheet description with minimum, typical and maximum values can be used.
+
+Example:
+
+ timing1: timing {
+ /* 1920x1080p24 */
+ clock-frequency = <148500000>;
+ hactive = <1920>;
+ vactive = <1080>;
+ hsync-len = <0 44 60>;
+ hfront-porch = <80 88 95>;
+ hback-porch = <100 148 160>;
+ vfront-porch = <0 4 6>;
+ vback-porch = <0 36 50>;
+ vsync-len = <0 5 6>;
+ };
--- /dev/null
+Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
+
+Required properties:
+- compatible: should be "edt,et057090dhu"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Emerging Display Technology Corp. ET070080DH6 7.0" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "edt,et070080dh6"
+
+This panel is the same as ETM0700G0DH6 except for the touchscreen.
+ET070080DH6 is the model with resistive touch.
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Emerging Display Technology Corp. ETM0700G0DH6 7.0" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "edt,etm0700g0dh6"
+
+This panel is the same as ET070080DH6 except for the touchscreen.
+ETM0700G0DH6 is the model with capacitive multitouch.
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Foxlink Group 5" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "foxlink,fl500wvr00-a0t"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+GiantPlus GPG48273QS5 4.3" (480x272) WQVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "giantplus,gpg48273qs5"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+HannStar Display Corp. HSD070PWW1 7.0" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "hannstar,hsd070pww1"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+HannStar Display Corp. HSD100PXN1 10.1" XGA LVDS panel
+
+Required properties:
+- compatible: should be "hannstar,hsd100pxn1"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Hitachi Ltd. Corporation 9" WVGA (800x480) TFT LCD panel
+
+Required properties:
+- compatible: should be "hit,tx23d38vm0caa"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Innolux AT043TN24 4.3" WQVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,at043tn24"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,g121i1-l01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,n116bge"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+InnoLux 15.6" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,n156bge-l21"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Innolux Corporation 7.0" WSVGA (1024x600) TFT LCD panel
+
+Required properties:
+- compatible: should be "innolux,zj070na-01p"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+LG 7" (800x480 pixels) TFT LCD panel
+
+Required properties:
+- compatible: should be "lg,lb070wv8"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+LG Corporation 7" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "lg,ld070wx3-sl01"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+LG LG4573 TFT Liquid Crystal Display with SPI control bus
+
+Required properties:
+ - compatible: "lg,lg4573"
+ - reg: address of the panel on the SPI bus
+
+The panel must obey rules for SPI slave device specified in document [1].
+
+[1]: Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+ lcd_panel: display@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ };
--- /dev/null
+LG Corporation 5" HD TFT LCD panel
+
+Required properties:
+- compatible: should be "lg,lh500wx1-sd03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+LG 12.9" (2560x1700 pixels) TFT LCD panel
+
+Required properties:
+- compatible: should be "lg,lp129qe"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+LG.Philips LB035Q02 Panel
+=========================
+
+Required properties:
+- compatible: "lgphilips,lb035q02"
+- enable-gpios: panel enable gpio
+
+Optional properties:
+- label: a symbolic name for the panel
+
+Required nodes:
+- Video port for DPI input
+
+Example
+-------
+
+lcd-panel: panel@0 {
+ compatible = "lgphilips,lb035q02";
+ reg = <0>;
+ spi-max-frequency = <100000>;
+ spi-cpol;
+ spi-cpha;
+
+ label = "lcd";
+
+ enable-gpios = <&gpio7 7 0>;
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+};
--- /dev/null
+NEC LCD Technologies,Ltd. WQVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "nec,nl4827hc19-05b"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+OKAYA Electric America, Inc. RS800480T-7X0GP 7" WVGA LCD panel
+
+Required properties:
+- compatible: should be "okaya,rs800480t-7x0gp"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+OrtusTech COM43H4M85ULC Blanview 3.7" TFT-LCD panel
+
+Required properties:
+- compatible: should be "ortustech,com43h4m85ulc"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Panasonic Corporation 10.1" WUXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "panasonic,vvx10f004b00"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Generic MIPI DPI Panel
+======================
+
+Required properties:
+- compatible: "panel-dpi"
+
+Optional properties:
+- label: a symbolic name for the panel
+- enable-gpios: panel enable gpio
+
+Required nodes:
+- "panel-timing" containing video timings
+ (Documentation/devicetree/bindings/display/display-timing.txt)
+- Video port for DPI input
+
+Example
+-------
+
+lcd0: display@0 {
+ compatible = "samsung,lte430wq-f0c", "panel-dpi";
+ label = "lcd";
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ panel-timing {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+};
--- /dev/null
+Generic MIPI DSI Command Mode Panel
+===================================
+
+Required properties:
+- compatible: "panel-dsi-cm"
+
+Optional properties:
+- label: a symbolic name for the panel
+- reset-gpios: panel reset gpio
+- te-gpios: panel TE gpio
+
+Required nodes:
+- Video port for DSI input
+
+Example
+-------
+
+lcd0: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd0";
+
+ reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
+
+ port {
+ lcd0_in: endpoint {
+ remote-endpoint = <&dsi1_out_ep>;
+ };
+ };
+};
--- /dev/null
+Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus
+
+Required properties:
+ - compatible: "samsung,ld9040"
+ - reg: address of the panel on SPI bus
+ - vdd3-supply: core voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpios: a GPIO spec for the reset pin
+ - display-timings: timings for the connected panel according to [1]
+
+The panel must obey rules for SPI slave device specified in document [2].
+
+Optional properties:
+ - power-on-delay: delay after turning regulators on [ms]
+ - reset-delay: delay after reset sequence [ms]
+ - panel-width-mm: physical panel width [mm]
+ - panel-height-mm: physical panel height [mm]
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [3]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+[2]: Documentation/devicetree/bindings/spi/spi-bus.txt
+[3]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ lcd@0 {
+ compatible = "samsung,ld9040";
+ reg = <0>;
+ vdd3-supply = <&ldo7_reg>;
+ vci-supply = <&ldo17_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ spi-max-frequency = <1200000>;
+ spi-cpol;
+ spi-cpha;
+ power-on-delay = <10>;
+ reset-delay = <10>;
+ panel-width-mm = <90>;
+ panel-height-mm = <154>;
+
+ display-timings {
+ timing {
+ clock-frequency = <23492370>;
+ hactive = <480>;
+ vactive = <800>;
+ hback-porch = <16>;
+ hfront-porch = <16>;
+ vback-porch = <2>;
+ vfront-porch = <28>;
+ hsync-len = <2>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <0>;
+ pixelclk-active = <0>;
+ };
+ };
+
+ port {
+ lcd_ep: endpoint {
+ remote-endpoint = <&fimd_dpi_ep>;
+ };
+ };
+ };
--- /dev/null
+Samsung Electronics 10.1" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "samsung,ltn101nt05"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Samsung Electronics 14" WXGA (1366x768) TFT LCD panel
+
+Required properties:
+- compatible: should be "samsung,ltn140at29-301"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Samsung S6E8AA0 AMOLED LCD 5.3 inch panel
+
+Required properties:
+ - compatible: "samsung,s6e8aa0"
+ - reg: the virtual channel number of a DSI peripheral
+ - vdd3-supply: core voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpios: a GPIO spec for the reset pin
+ - display-timings: timings for the connected panel as described by [1]
+
+Optional properties:
+ - power-on-delay: delay after turning regulators on [ms]
+ - reset-delay: delay after reset sequence [ms]
+ - init-delay: delay after initialization sequence [ms]
+ - panel-width-mm: physical panel width [mm]
+ - panel-height-mm: physical panel height [mm]
+ - flip-horizontal: boolean to flip image horizontally
+ - flip-vertical: boolean to flip image vertically
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/display/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ panel {
+ compatible = "samsung,s6e8aa0";
+ reg = <0>;
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+ flip-horizontal;
+ flip-vertical;
+
+ display-timings {
+ timing0: timing-0 {
+ clock-frequency = <57153600>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+ };
--- /dev/null
+Sharp Microelectronics 10.1" WQXGA TFT LCD panel
+
+This panel requires a dual-channel DSI host to operate. It supports two modes:
+- left-right: each channel drives the left or right half of the screen
+- even-odd: each channel drives the even or odd lines of the screen
+
+Each of the DSI channels controls a separate DSI peripheral. The peripheral
+driven by the first link (DSI-LINK1), left or even, is considered the primary
+peripheral and controls the device. The 'link2' property contains a phandle
+to the peripheral driven by the second link (DSI-LINK2, right or odd).
+
+Note that in video mode the DSI-LINK1 interface always provides the left/even
+pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it
+is possible to program either link to drive the left/even or right/odd pixels
+but for the sake of consistency this binding assumes that the same assignment
+is chosen as for video mode.
+
+Required properties:
+- compatible: should be "sharp,lq101r1sx01"
+- reg: DSI virtual channel of the peripheral
+
+Required properties (for DSI-LINK1 only):
+- link2: phandle to the DSI peripheral on the secondary link. Note that the
+ presence of this property marks the containing node as DSI-LINK1.
+- power-supply: phandle of the regulator that provides the supply voltage
+
+Optional properties (for DSI-LINK1 only):
+- backlight: phandle of the backlight device attached to the panel
+
+Example:
+
+ dsi@54300000 {
+ panel: panel@0 {
+ compatible = "sharp,lq101r1sx01";
+ reg = <0>;
+
+ link2 = <&secondary>;
+
+ power-supply = <...>;
+ backlight = <...>;
+ };
+ };
+
+ dsi@54400000 {
+ secondary: panel@0 {
+ compatible = "sharp,lq101r1sx01";
+ reg = <0>;
+ };
+ };
--- /dev/null
+SHARP LS037V7DW01 TFT-LCD panel
+===================================
+
+Required properties:
+- compatible: "sharp,ls037v7dw01"
+
+Optional properties:
+- label: a symbolic name for the panel
+- enable-gpios: a GPIO spec for the optional enable pin.
+ This pin is the INI pin as specified in the LS037V7DW01.pdf file.
+- reset-gpios: a GPIO spec for the optional reset pin.
+ This pin is the RESB pin as specified in the LS037V7DW01.pdf file.
+- mode-gpios: a GPIO
+ ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file.
+
+Required nodes:
+- Video port for DPI input
+
+This panel can have zero to five GPIOs to configure to change configuration
+between QVGA and VGA mode and the scan direction. As these pins can be also
+configured with external pulls, all the GPIOs are considered optional with holes
+in the array.
+
+Example
+-------
+
+Example when connected to a omap2+ based device:
+
+lcd0: display {
+ compatible = "sharp,ls037v7dw01";
+ power-supply = <&lcd_3v3>;
+ enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
+ reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
+ mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
+ &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
+ &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+};
--- /dev/null
+Shelly SCA07010-BFN-LNN 7.0" WVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "shelly,sca07010-bfn-lnn"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--- /dev/null
+Simple display panel
+
+Required properties:
+- power-supply: regulator to provide the supply voltage
+
+Optional properties:
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+
+Example:
+
+ panel: panel {
+ compatible = "cptt,claa101wb01";
+ ddc-i2c-bus = <&panelddc>;
+
+ power-supply = <&vdd_pnl_reg>;
+ enable-gpios = <&gpio 90 0>;
+
+ backlight = <&backlight>;
+ };
--- /dev/null
+Sony ACX565AKM SDI Panel
+========================
+
+Required properties:
+- compatible: "sony,acx565akm"
+
+Optional properties:
+- label: a symbolic name for the panel
+- reset-gpios: panel reset gpio
+
+Required nodes:
+- Video port for SDI input
+
+Example
+-------
+
+acx565akm@2 {
+ compatible = "sony,acx565akm";
+ spi-max-frequency = <6000000>;
+ reg = <2>;
+
+ label = "lcd";
+ reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&sdi_out>;
+ };
+ };
+};
--- /dev/null
+Toppoly TD028TTEC1 Panel
+========================
+
+Required properties:
+- compatible: "toppoly,td028ttec1"
+
+Optional properties:
+- label: a symbolic name for the panel
+
+Required nodes:
+- Video port for DPI input
+
+Example
+-------
+
+lcd-panel: td028ttec1@0 {
+ compatible = "toppoly,td028ttec1";
+ reg = <0>;
+ spi-max-frequency = <100000>;
+ spi-cpol;
+ spi-cpha;
+
+ label = "lcd";
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+};
+
--- /dev/null
+TPO TD043MTEA1 Panel
+====================
+
+Required properties:
+- compatible: "tpo,td043mtea1"
+- reset-gpios: panel reset gpio
+
+Optional properties:
+- label: a symbolic name for the panel
+
+Required nodes:
+- Video port for DPI input
+
+Example
+-------
+
+lcd-panel: panel@0 {
+ compatible = "tpo,td043mtea1";
+ reg = <0>;
+ spi-max-frequency = <100000>;
+ spi-cpol;
+ spi-cpha;
+
+ label = "lcd";
+
+ reset-gpios = <&gpio7 7 0>;
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+};
--- /dev/null
+* Renesas R-Car Display Unit (DU)
+
+Required Properties:
+
+ - compatible: must be one of the following.
+ - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU
+ - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU
+ - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU
+
+ - reg: A list of base address and length of each memory resource, one for
+ each entry in the reg-names property.
+ - reg-names: Name of the memory resources. The DU requires one memory
+ resource for the DU core (named "du") and one memory resource for each
+ LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical
+ index).
+
+ - interrupt-parent: phandle of the parent interrupt controller.
+ - interrupts: Interrupt specifiers for the DU interrupts.
+
+ - clocks: A list of phandles + clock-specifier pairs, one for each entry in
+ the clock-names property.
+ - clock-names: Name of the clocks. This property is model-dependent.
+ - R8A7779 uses a single functional clock. The clock doesn't need to be
+ named.
+ - R8A7790 and R8A7791 use one functional clock per channel and one clock
+ per LVDS encoder. The functional clocks must be named "du.x" with "x"
+ being the channel numerical index. The LVDS clocks must be named
+ "lvds.x" with "x" being the LVDS encoder numerical index.
+ - In addition to the functional and encoder clocks, all DU versions also
+ support externally supplied pixel clocks. Those clocks are optional.
+ When supplied they must be named "dclkin.x" with "x" being the input
+ clock numerical index.
+
+Required nodes:
+
+The connections to the DU output video ports are modeled using the OF graph
+bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+The following table lists for each supported model the port number
+corresponding to each DU output.
+
+ Port 0 Port1 Port2
+-----------------------------------------------------------------------------
+ R8A7779 (H1) DPAD 0 DPAD 1 -
+ R8A7790 (H2) DPAD LVDS 0 LVDS 1
+ R8A7791 (M2) DPAD LVDS 0 -
+
+
+Example: R8A7790 (R-Car H2) DU
+
+ du: du@feb00000 {
+ compatible = "renesas,du-r8a7790";
+ reg = <0 0xfeb00000 0 0x70000>,
+ <0 0xfeb90000 0 0x1c>,
+ <0 0xfeb94000 0 0x1c>;
+ reg-names = "du", "lvds.0", "lvds.1";
+ interrupt-parent = <&gic>;
+ interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>,
+ <0 268 IRQ_TYPE_LEVEL_HIGH>,
+ <0 269 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp7_clks R8A7790_CLK_DU0>,
+ <&mstp7_clks R8A7790_CLK_DU1>,
+ <&mstp7_clks R8A7790_CLK_DU2>,
+ <&mstp7_clks R8A7790_CLK_LVDS0>,
+ <&mstp7_clks R8A7790_CLK_LVDS1>;
+ clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ du_out_rgb: endpoint {
+ };
+ };
+ port@1 {
+ reg = <1>;
+ du_out_lvds0: endpoint {
+ };
+ };
+ port@2 {
+ reg = <2>;
+ du_out_lvds1: endpoint {
+ };
+ };
+ };
+ };
--- /dev/null
+Rockchip specific extensions to the Synopsys Designware HDMI
+================================
+
+Required properties:
+- compatible: "rockchip,rk3288-dw-hdmi";
+- reg: Physical base address and length of the controller's registers.
+- clocks: phandle to hdmi iahb and isfr clocks.
+- clock-names: should be "iahb" "isfr"
+- rockchip,grf: this soc should set GRF regs to mux vopl/vopb.
+- interrupts: HDMI interrupt number
+- ports: contain a port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt. For
+ vopb,set the reg = <0> and set the reg = <1> for vopl.
+- reg-io-width: the width of the reg:1,4, the value should be 4 on
+ rk3288 platform
+
+Optional properties
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
+
+Example:
+hdmi: hdmi@ff980000 {
+ compatible = "rockchip,rk3288-dw-hdmi";
+ reg = <0xff980000 0x20000>;
+ reg-io-width = <4>;
+ ddc-i2c-bus = <&i2c5>;
+ rockchip,grf = <&grf>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
+ clock-names = "iahb", "isfr";
+ status = "disabled";
+ ports {
+ hdmi_in: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ hdmi_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_hdmi>;
+ };
+ hdmi_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_hdmi>;
+ };
+ };
+ };
+};
--- /dev/null
+Rockchip DRM master device
+================================
+
+The Rockchip DRM master device is a virtual device needed to list all
+vop devices or other display interface nodes that comprise the
+graphics subsystem.
+
+Required properties:
+- compatible: Should be "rockchip,display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface port
+ of vop devices. vop definitions as defined in
+ Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt
+
+example:
+
+display-subsystem {
+ compatible = "rockchip,display-subsystem";
+ ports = <&vopl_out>, <&vopb_out>;
+};
--- /dev/null
+device-tree bindings for rockchip soc display controller (vop)
+
+VOP (Visual Output Processor) is the Display Controller for the Rockchip
+series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+ "rockchip,rk3288-vop";
+
+- interrupts: should contain a list of all VOP IP block interrupts in the
+ order: VSYNC, LCD_SYSTEM. The interrupt specifier
+ format depends on the interrupt controller used.
+
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+
+- clock-names: Must contain
+ aclk_vop: for ddr buffer transfer.
+ hclk_vop: for ahb bus to R/W the phy regs.
+ dclk_vop: pixel clock.
+
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - axi
+ - ahb
+ - dclk
+
+- iommus: required a iommu node
+
+- port: A port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+SoC specific DT entry:
+ vopb: vopb@ff930000 {
+ compatible = "rockchip,rk3288-vop";
+ reg = <0xff930000 0x19c>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>;
+ clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
+ resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>;
+ reset-names = "axi", "ahb", "dclk";
+ iommus = <&vopb_mmu>;
+ vopb_out: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vopb_out_edp: endpoint@0 {
+ reg = <0>;
+ remote-endpoint=<&edp_in_vopb>;
+ };
+ vopb_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint=<&hdmi_in_vopb>;
+ };
+ };
+ };
--- /dev/null
+Sunxi specific Simple Framebuffer bindings
+
+This binding documents sunxi specific extensions to the simple-framebuffer
+bindings. The sunxi simplefb u-boot code relies on the devicetree containing
+pre-populated simplefb nodes.
+
+These extensions are intended so that u-boot can select the right node based
+on which pipeline is being used. As such they are solely intended for
+firmware / bootloader use, and the OS should ignore them.
+
+Required properties:
+- compatible: "allwinner,simple-framebuffer"
+- allwinner,pipeline, one of:
+ "de_be0-lcd0"
+ "de_be1-lcd1"
+ "de_be0-lcd0-hdmi"
+ "de_be1-lcd1-hdmi"
+
+Example:
+
+chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-hdmi";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>;
+ status = "disabled";
+ };
+};
--- /dev/null
+Simple Framebuffer
+
+A simple frame-buffer describes a frame-buffer setup by firmware or
+the bootloader, with the assumption that the display hardware has already
+been set up to scan out from the memory pointed to by the reg property.
+
+Since simplefb nodes represent runtime information they must be sub-nodes of
+the chosen node (*). Simplefb nodes must be named "framebuffer@<address>".
+
+If the devicetree contains nodes for the display hardware used by a simplefb,
+then the simplefb node must contain a property called "display", which
+contains a phandle pointing to the primary display hw node, so that the OS
+knows which simplefb to disable when handing over control to a driver for the
+real hardware. The bindings for the hw nodes must specify which node is
+considered the primary node.
+
+It is advised to add display# aliases to help the OS determine how to number
+things. If display# aliases are used, then if the simplefb node contains a
+"display" property then the /aliases/display# path must point to the display
+hw node the "display" property points to, otherwise it must point directly
+to the simplefb node.
+
+If a simplefb node represents the preferred console for user interaction,
+then the chosen node's stdout-path property should point to it, or to the
+primary display hw node, as with display# aliases. If display aliases are
+used then it should be set to the alias instead.
+
+It is advised that devicetree files contain pre-filled, disabled framebuffer
+nodes, so that the firmware only needs to update the mode information and
+enable them. This way if e.g. later on support for more display clocks get
+added, the simplefb nodes will already contain this info and the firmware
+does not need to be updated.
+
+If pre-filled framebuffer nodes are used, the firmware may need extra
+information to find the right node. In that case an extra platform specific
+compatible and platform specific properties should be used and documented,
+see e.g. simple-framebuffer-sunxi.txt .
+
+Required properties:
+- compatible: "simple-framebuffer"
+- reg: Should contain the location and size of the framebuffer memory.
+- width: The width of the framebuffer in pixels.
+- height: The height of the framebuffer in pixels.
+- stride: The number of bytes in each line of the framebuffer.
+- format: The format of the framebuffer surface. Valid values are:
+ - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
+ - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r).
+
+Optional properties:
+- clocks : List of clocks used by the framebuffer. Clocks listed here
+ are expected to already be configured correctly. The OS must
+ ensure these clocks are not modified or disabled while the
+ simple framebuffer remains active.
+- display : phandle pointing to the primary display hardware node
+
+Example:
+
+aliases {
+ display0 = &lcdc0;
+}
+
+chosen {
+ framebuffer0: framebuffer@1d385000 {
+ compatible = "simple-framebuffer";
+ reg = <0x1d385000 (1600 * 1200 * 2)>;
+ width = <1600>;
+ height = <1200>;
+ stride = <(1600 * 2)>;
+ format = "r5g6b5";
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>;
+ display = <&lcdc0>;
+ };
+ stdout-path = "display0";
+};
+
+soc@01c00000 {
+ lcdc0: lcdc@1c0c000 {
+ compatible = "allwinner,sun4i-a10-lcdc";
+ ...
+ };
+};
+
+
+*) Older devicetree files may have a compatible = "simple-framebuffer" node
+in a different place, operating systems must first enumerate any compatible
+nodes found under chosen and then check for other compatible nodes.
--- /dev/null
+* SM SM501
+
+The SM SM501 is a LCD controller, with proper hardware, it can also
+drive DVI monitors.
+
+Required properties:
+- compatible : should be "smi,sm501".
+- reg : contain two entries:
+ - First entry: System Configuration register
+ - Second entry: IO space (Display Controller register)
+- interrupts : SMI interrupt to the cpu should be described here.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Optional properties:
+- mode : select a video mode:
+ <xres>x<yres>[-<bpp>][@<refresh>]
+- edid : verbatim EDID data block describing attached display.
+ Data from the detailed timing descriptor will be used to
+ program the display controller.
+- little-endian: available on big endian systems, to
+ set different foreign endian.
+- big-endian: available on little endian systems, to
+ set different foreign endian.
+
+Example for MPC5200:
+ display@1,0 {
+ compatible = "smi,sm501";
+ reg = <1 0x00000000 0x00800000
+ 1 0x03e00000 0x00200000>;
+ interrupts = <1 1 3>;
+ mode = "640x480-32@60";
+ edid = [edid-data];
+ };
--- /dev/null
+* Solomon SSD1289 Framebuffer Driver
+
+Required properties:
+ - compatible: Should be "solomon,ssd1289fb". The only supported bus for
+ now is lbc.
+ - reg: Should contain address of the controller on the LBC bus. The detail
+ was described in Documentation/devicetree/bindings/powerpc/fsl/lbc.txt
+
+Examples:
+display@2,0 {
+ compatible = "solomon,ssd1289fb";
+ reg = <0x2 0x0000 0x0004>;
+};
--- /dev/null
+* Solomon SSD1307 Framebuffer Driver
+
+Required properties:
+ - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for
+ now is i2c, and the supported chips are ssd1305, ssd1306 and ssd1307.
+ - reg: Should contain address of the controller on the I2C bus. Most likely
+ 0x3c or 0x3d
+ - pwm: Should contain the pwm to use according to the OF device tree PWM
+ specification [0]. Only required for the ssd1307.
+ - reset-gpios: Should contain the GPIO used to reset the OLED display
+ - solomon,height: Height in pixel of the screen driven by the controller
+ - solomon,width: Width in pixel of the screen driven by the controller
+ - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
+ mapped to.
+
+Optional properties:
+ - reset-active-low: Is the reset gpio is active on physical low?
+ - solomon,segment-no-remap: Display needs normal (non-inverted) data column
+ to segment mapping
+ - solomon,com-seq: Display uses sequential COM pin configuration
+ - solomon,com-lrremap: Display uses left-right COM pin remap
+ - solomon,com-invdir: Display uses inverted COM pin scan direction
+ - solomon,com-offset: Number of the COM pin wired to the first display line
+ - solomon,prechargep1: Length of deselect period (phase 1) in clock cycles.
+ - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles.
+ This needs to be the higher, the higher the capacitance
+ of the OLED's pixels is
+
+[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+
+Examples:
+ssd1307: oled@3c {
+ compatible = "solomon,ssd1307fb-i2c";
+ reg = <0x3c>;
+ pwms = <&pwm 4 3000>;
+ reset-gpios = <&gpio2 7>;
+ reset-active-low;
+};
+
+ssd1306: oled@3c {
+ compatible = "solomon,ssd1306fb-i2c";
+ reg = <0x3c>;
+ pwms = <&pwm 4 3000>;
+ reset-gpios = <&gpio2 7>;
+ reset-active-low;
+ solomon,com-lrremap;
+ solomon,com-invdir;
+ solomon,com-offset = <32>;
+};
--- /dev/null
+STMicroelectronics stih4xx platforms
+
+- sti-vtg: video timing generator
+ Required properties:
+ - compatible: "st,vtg"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ Optional properties:
+ - interrupts : VTG interrupt number to the CPU.
+ - st,slave: phandle on a slave vtg
+
+- sti-vtac: video timing advanced inter dye communication Rx and TX
+ Required properties:
+ - compatible: "st,vtac-main" or "st,vtac-aux"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+
+- sti-display-subsystem: Master device for DRM sub-components
+ This device must be the parent of all the sub-components and is responsible
+ of bind them.
+ Required properties:
+ - compatible: "st,sti-display-subsystem"
+ - ranges: to allow probing of subdevices
+
+- sti-compositor: frame compositor engine
+ must be a child of sti-display-subsystem
+ Required properties:
+ - compatible: "st,stih<chip>-compositor"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+ - resets: resets to be used by the device
+ See ../reset/reset.txt for details.
+ - reset-names: names of the resets listed in resets property in the same
+ order.
+ - st,vtg: phandle(s) on vtg device (main and aux) nodes.
+
+- sti-tvout: video out hardware block
+ must be a child of sti-display-subsystem
+ Required properties:
+ - compatible: "st,stih<chip>-tvout"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - reg-names: names of the mapped memory regions listed in regs property in
+ the same order.
+ - resets: resets to be used by the device
+ See ../reset/reset.txt for details.
+ - reset-names: names of the resets listed in resets property in the same
+ order.
+
+- sti-hdmi: hdmi output block
+ must be a child of sti-display-subsystem
+ Required properties:
+ - compatible: "st,stih<chip>-hdmi";
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - reg-names: names of the mapped memory regions listed in regs property in
+ the same order.
+ - interrupts : HDMI interrupt number to the CPU.
+ - interrupt-names: name of the interrupts listed in interrupts property in
+ the same order
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+ - ddc: phandle of an I2C controller used for DDC EDID probing
+
+sti-hda:
+ Required properties:
+ must be a child of sti-display-subsystem
+ - compatible: "st,stih<chip>-hda"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - reg-names: names of the mapped memory regions listed in regs property in
+ the same order.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+
+sti-dvo:
+ Required properties:
+ must be a child of sti-display-subsystem
+ - compatible: "st,stih<chip>-dvo"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - reg-names: names of the mapped memory regions listed in regs property in
+ the same order.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+ - pinctrl-0: pin control handle
+ - pinctrl-name: names of the pin control to use
+ - sti,panel: phandle of the panel connected to the DVO output
+
+sti-hqvdp:
+ must be a child of sti-display-subsystem
+ Required properties:
+ - compatible: "st,stih<chip>-hqvdp"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+ - resets: resets to be used by the device
+ See ../reset/reset.txt for details.
+ - reset-names: names of the resets listed in resets property in the same
+ order.
+ - st,vtg: phandle on vtg main device node.
+
+Example:
+
+/ {
+ ...
+
+ vtg_main_slave: sti-vtg-main-slave@fe85A800 {
+ compatible = "st,vtg";
+ reg = <0xfe85A800 0x300>;
+ interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>;
+ };
+
+ vtg_main: sti-vtg-main-master@fd348000 {
+ compatible = "st,vtg";
+ reg = <0xfd348000 0x400>;
+ st,slave = <&vtg_main_slave>;
+ };
+
+ vtg_aux_slave: sti-vtg-aux-slave@fd348400 {
+ compatible = "st,vtg";
+ reg = <0xfe858200 0x300>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_NONE>;
+ };
+
+ vtg_aux: sti-vtg-aux-master@fd348400 {
+ compatible = "st,vtg";
+ reg = <0xfd348400 0x400>;
+ st,slave = <&vtg_aux_slave>;
+ };
+
+
+ sti-vtac-rx-main@fee82800 {
+ compatible = "st,vtac-main";
+ reg = <0xfee82800 0x200>;
+ clock-names = "vtac";
+ clocks = <&clk_m_a2_div0 CLK_M_VTAC_MAIN_PHY>;
+ };
+
+ sti-vtac-rx-aux@fee82a00 {
+ compatible = "st,vtac-aux";
+ reg = <0xfee82a00 0x200>;
+ clock-names = "vtac";
+ clocks = <&clk_m_a2_div0 CLK_M_VTAC_AUX_PHY>;
+ };
+
+ sti-vtac-tx-main@fd349000 {
+ compatible = "st,vtac-main";
+ reg = <0xfd349000 0x200>, <0xfd320000 0x10000>;
+ clock-names = "vtac";
+ clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
+ };
+
+ sti-vtac-tx-aux@fd349200 {
+ compatible = "st,vtac-aux";
+ reg = <0xfd349200 0x200>, <0xfd320000 0x10000>;
+ clock-names = "vtac";
+ clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
+ };
+
+ sti-display-subsystem {
+ compatible = "st,sti-display-subsystem";
+ ranges;
+
+ sti-compositor@fd340000 {
+ compatible = "st,stih416-compositor";
+ reg = <0xfd340000 0x1000>;
+ clock-names = "compo_main", "compo_aux",
+ "pix_main", "pix_aux";
+ clocks = <&clk_m_a2_div1 CLK_M_COMPO_MAIN>, <&clk_m_a2_div1 CLK_M_COMPO_AUX>,
+ <&clockgen_c_vcc CLK_S_PIX_MAIN>, <&clockgen_c_vcc CLK_S_PIX_AUX>;
+ reset-names = "compo-main", "compo-aux";
+ resets = <&softreset STIH416_COMPO_M_SOFTRESET>, <&softreset STIH416_COMPO_A_SOFTRESET>;
+ st,vtg = <&vtg_main>, <&vtg_aux>;
+ };
+
+ sti-tvout@fe000000 {
+ compatible = "st,stih416-tvout";
+ reg = <0xfe000000 0x1000>, <0xfe85a000 0x400>, <0xfe830000 0x10000>;
+ reg-names = "tvout-reg", "hda-reg", "syscfg";
+ reset-names = "tvout";
+ resets = <&softreset STIH416_HDTVOUT_SOFTRESET>;
+ };
+
+ sti-hdmi@fe85c000 {
+ compatible = "st,stih416-hdmi";
+ reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>;
+ reg-names = "hdmi-reg", "syscfg";
+ interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>;
+ interrupt-names = "irq";
+ clock-names = "pix", "tmds", "phy", "audio";
+ clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>;
+ };
+
+ sti-hda@fe85a000 {
+ compatible = "st,stih416-hda";
+ reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>;
+ reg-names = "hda-reg", "video-dacs-ctrl";
+ clock-names = "pix", "hddac";
+ clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>;
+ };
+
+ sti-dvo@8d00400 {
+ compatible = "st,stih407-dvo";
+ reg = <0x8d00400 0x200>;
+ reg-names = "dvo-reg";
+ clock-names = "dvo_pix", "dvo",
+ "main_parent", "aux_parent";
+ clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>,
+ <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dvo>;
+ sti,panel = <&panel_dvo>;
+ };
+
+ sti-hqvdp@9c000000 {
+ compatible = "st,stih407-hqvdp";
+ reg = <0x9C00000 0x100000>;
+ clock-names = "hqvdp", "pix_main";
+ clocks = <&clk_s_c0_flexgen CLK_MAIN_DISP>, <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>;
+ reset-names = "hqvdp";
+ resets = <&softreset STIH407_HDQVDP_SOFTRESET>;
+ st,vtg = <&vtg_main>;
+ };
+ };
+ ...
+};
--- /dev/null
+NVIDIA Tegra MIPI pad calibration controller
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-mipi"
+- reg: Physical base address and length of the controller's registers.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - mipi-cal
+- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads
+ that need to be calibrated for a given device.
+
+User nodes need to contain an nvidia,mipi-calibrate property that has a
+phandle to refer to the calibration controller node and a bitmask of the pads
+that need to be calibrated.
+
+Example:
+
+ mipi: mipi@700e3000 {
+ compatible = "nvidia,tegra114-mipi";
+ reg = <0x700e3000 0x100>;
+ clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
+ clock-names = "mipi-cal";
+ #nvidia,mipi-calibrate-cells = <1>;
+ };
+
+ ...
+
+ host1x@50000000 {
+ ...
+
+ dsi@54300000 {
+ ...
+
+ nvidia,mipi-calibrate = <&mipi 0x060>;
+
+ ...
+ };
+
+ ...
+ };
--- /dev/null
+NVIDIA Tegra host1x
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-host1x"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller.
+- #address-cells: The number of cells used to represent physical base addresses
+ in the host1x address space. Should be 1.
+- #size-cells: The number of cells used to represent the size of an address
+ range in the host1x address space. Should be 1.
+- ranges: The mapping of the host1x address space to the CPU address space.
+- clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - host1x
+
+The host1x top-level node defines a number of children, each representing one
+of the following host1x client modules:
+
+- mpe: video encoder
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-mpe"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - mpe
+
+- vi: video input
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-vi"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - vi
+
+- epp: encoder pre-processor
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-epp"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - epp
+
+- isp: image signal processor
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-isp"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - isp
+
+- gr2d: 2D graphics engine
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-gr2d"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - 2d
+
+- gr3d: 3D graphics engine
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-gr3d"
+ - reg: Physical base address and length of the controller's registers.
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ (This property may be omitted if the only clock in the list is "3d")
+ - 3d
+ This MUST be the first entry.
+ - 3d2 (Only required on SoCs with two 3D clocks)
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - 3d
+ - 3d2 (Only required on SoCs with two 3D clocks)
+
+- dc: display controller
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-dc"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ - dc
+ This MUST be the first entry.
+ - parent
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - dc
+ - nvidia,head: The number of the display controller head. This is used to
+ setup the various types of output to receive video data from the given
+ head.
+
+ Each display controller node has a child node, named "rgb", that represents
+ the RGB output associated with the controller. It can take the following
+ optional properties:
+ - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+ - nvidia,edid: supplies a binary EDID blob
+ - nvidia,panel: phandle of a display panel
+
+- hdmi: High Definition Multimedia Interface
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-hdmi"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - hdmi-supply: supply for the +5V HDMI connector pin
+ - vdd-supply: regulator for supply voltage
+ - pll-supply: regulator for PLL
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ - hdmi
+ This MUST be the first entry.
+ - parent
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - hdmi
+
+ Optional properties:
+ - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+ - nvidia,edid: supplies a binary EDID blob
+ - nvidia,panel: phandle of a display panel
+
+- tvo: TV encoder output
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-tvo"
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
+
+- dsi: display serial interface
+
+ Required properties:
+ - compatible: "nvidia,tegra<chip>-dsi"
+ - reg: Physical base address and length of the controller's registers.
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ - dsi
+ This MUST be the first entry.
+ - lp
+ - parent
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - dsi
+ - avdd-dsi-supply: phandle of a supply that powers the DSI controller
+ - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
+ which pads are used by this DSI output and need to be calibrated. See also
+ ../display/tegra/nvidia,tegra114-mipi.txt.
+
+ Optional properties:
+ - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+ - nvidia,edid: supplies a binary EDID blob
+ - nvidia,panel: phandle of a display panel
+ - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang
+ up with in order to support up to 8 data lanes
+
+- sor: serial output resource
+
+ Required properties:
+ - compatible: Should be:
+ - "nvidia,tegra124-sor": for Tegra124 and Tegra132
+ - "nvidia,tegra132-sor": for Tegra132
+ - "nvidia,tegra210-sor": for Tegra210
+ - "nvidia,tegra210-sor1": for Tegra210
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ - sor: clock input for the SOR hardware
+ - parent: input for the pixel clock
+ - dp: reference clock for the SOR clock
+ - safe: safe reference for the SOR clock during power up
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - sor
+
+ Optional properties:
+ - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+ - nvidia,edid: supplies a binary EDID blob
+ - nvidia,panel: phandle of a display panel
+
+ Optional properties when driving an eDP output:
+ - nvidia,dpaux: phandle to a DispayPort AUX interface
+
+- dpaux: DisplayPort AUX interface
+ - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise,
+ must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where
+ <chip> is tegra132.
+ - reg: Physical base address and length of the controller's registers.
+ - interrupts: The interrupt outputs from the controller.
+ - clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must include the following entries:
+ - dpaux: clock input for the DPAUX hardware
+ - parent: reference clock
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - dpaux
+ - vdd-supply: phandle of a supply that powers the DisplayPort link
+
+Example:
+
+/ {
+ ...
+
+ host1x {
+ compatible = "nvidia,tegra20-host1x", "simple-bus";
+ reg = <0x50000000 0x00024000>;
+ interrupts = <0 65 0x04 /* mpcore syncpt */
+ 0 67 0x04>; /* mpcore general */
+ clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
+ resets = <&tegra_car 28>;
+ reset-names = "host1x";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x54000000 0x54000000 0x04000000>;
+
+ mpe {
+ compatible = "nvidia,tegra20-mpe";
+ reg = <0x54040000 0x00040000>;
+ interrupts = <0 68 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_MPE>;
+ resets = <&tegra_car 60>;
+ reset-names = "mpe";
+ };
+
+ vi {
+ compatible = "nvidia,tegra20-vi";
+ reg = <0x54080000 0x00040000>;
+ interrupts = <0 69 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_VI>;
+ resets = <&tegra_car 100>;
+ reset-names = "vi";
+ };
+
+ epp {
+ compatible = "nvidia,tegra20-epp";
+ reg = <0x540c0000 0x00040000>;
+ interrupts = <0 70 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_EPP>;
+ resets = <&tegra_car 19>;
+ reset-names = "epp";
+ };
+
+ isp {
+ compatible = "nvidia,tegra20-isp";
+ reg = <0x54100000 0x00040000>;
+ interrupts = <0 71 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_ISP>;
+ resets = <&tegra_car 23>;
+ reset-names = "isp";
+ };
+
+ gr2d {
+ compatible = "nvidia,tegra20-gr2d";
+ reg = <0x54140000 0x00040000>;
+ interrupts = <0 72 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_GR2D>;
+ resets = <&tegra_car 21>;
+ reset-names = "2d";
+ };
+
+ gr3d {
+ compatible = "nvidia,tegra20-gr3d";
+ reg = <0x54180000 0x00040000>;
+ clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+ resets = <&tegra_car 24>;
+ reset-names = "3d";
+ };
+
+ dc@54200000 {
+ compatible = "nvidia,tegra20-dc";
+ reg = <0x54200000 0x00040000>;
+ interrupts = <0 73 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_DISP1>,
+ <&tegra_car TEGRA20_CLK_PLL_P>;
+ clock-names = "dc", "parent";
+ resets = <&tegra_car 27>;
+ reset-names = "dc";
+
+ rgb {
+ status = "disabled";
+ };
+ };
+
+ dc@54240000 {
+ compatible = "nvidia,tegra20-dc";
+ reg = <0x54240000 0x00040000>;
+ interrupts = <0 74 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_DISP2>,
+ <&tegra_car TEGRA20_CLK_PLL_P>;
+ clock-names = "dc", "parent";
+ resets = <&tegra_car 26>;
+ reset-names = "dc";
+
+ rgb {
+ status = "disabled";
+ };
+ };
+
+ hdmi {
+ compatible = "nvidia,tegra20-hdmi";
+ reg = <0x54280000 0x00040000>;
+ interrupts = <0 75 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_HDMI>,
+ <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+ clock-names = "hdmi", "parent";
+ resets = <&tegra_car 51>;
+ reset-names = "hdmi";
+ status = "disabled";
+ };
+
+ tvo {
+ compatible = "nvidia,tegra20-tvo";
+ reg = <0x542c0000 0x00040000>;
+ interrupts = <0 76 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_TVO>;
+ status = "disabled";
+ };
+
+ dsi {
+ compatible = "nvidia,tegra20-dsi";
+ reg = <0x54300000 0x00040000>;
+ clocks = <&tegra_car TEGRA20_CLK_DSI>,
+ <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+ clock-names = "dsi", "parent";
+ resets = <&tegra_car 48>;
+ reset-names = "dsi";
+ status = "disabled";
+ };
+ };
+
+ ...
+};
--- /dev/null
+Texas Instruments DRA7x Display Subsystem
+=========================================
+
+See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,dra7-dss"
+- reg: address and length of the register spaces for 'dss'
+- ti,hwmods: "dss_core"
+- clocks: handle to fclk
+- clock-names: "fck"
+- syscon: phandle to control module core syscon node
+
+Optional properties:
+
+Some DRA7xx SoCs have one dedicated video PLL, some have two. These properties
+can be used to describe the video PLLs:
+
+- reg: address and length of the register spaces for 'pll1_clkctrl',
+ 'pll1', 'pll2_clkctrl', 'pll2'
+- clocks: handle to video1 pll clock and video2 pll clock
+- clock-names: "video1_clk" and "video2_clk"
+
+Required nodes:
+- DISPC
+
+Optional nodes:
+- DSS Submodules: HDMI
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,dra7-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+- clocks: handle to fclk
+- clock-names: "fck"
+
+HDMI
+----
+
+Required properties:
+- compatible: "ti,dra7-hdmi"
+- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
+ 'core'
+- reg-names: "wp", "pll", "phy", "core"
+- interrupts: the HDMI interrupt line
+- ti,hwmods: "dss_hdmi"
+- vdda-supply: vdda power supply
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+Optional nodes:
+- Video port for HDMI output
+
+HDMI Endpoint optional properties:
+- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
+ D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
--- /dev/null
+Texas Instruments OMAP Display Subsystem
+========================================
+
+Generic Description
+-------------------
+
+This document is a generic description of the OMAP Display Subsystem bindings.
+Binding details for each OMAP SoC version are described in respective binding
+documentation.
+
+The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and
+a number of encoder modules. All DSS versions contain DSS Core and DISPC, but
+the encoder modules vary.
+
+The DSS Core is the parent of the other DSS modules, and manages clock routing,
+integration to the SoC, etc.
+
+DISPC is the display controller, which reads pixels from the memory and outputs
+a RGB pixel stream to encoders.
+
+The encoder modules encode the received RGB pixel stream to a video output like
+HDMI, MIPI DPI, etc.
+
+Video Ports
+-----------
+
+The DSS Core and the encoders have video port outputs. The structure of the
+video ports is described in Documentation/devicetree/bindings/graph.txt,
+and the properties for the ports and endpoints for each encoder are
+described in the SoC's DSS binding documentation.
+
+The video ports are used to describe the connections to external hardware, like
+panels or external encoders.
+
+Aliases
+-------
+
+The board dts file may define aliases for displays to assign "displayX" style
+name for each display. If no aliases are defined, a semi-random number is used
+for the display.
+
+Example
+-------
+
+A shortened example of the DSS description for OMAP4, with non-relevant parts
+removed, defined in omap4.dtsi:
+
+dss: dss@58000000 {
+ compatible = "ti,omap4-dss";
+ reg = <0x58000000 0x80>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ clocks = <&dss_dss_clk>;
+ clock-names = "fck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@58001000 {
+ compatible = "ti,omap4-dispc";
+ reg = <0x58001000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "dss_dispc";
+ clocks = <&dss_dss_clk>;
+ clock-names = "fck";
+ };
+
+ hdmi: encoder@58006000 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0x58006000 0x200>,
+ <0x58006200 0x100>,
+ <0x58006300 0x100>,
+ <0x58006400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_hdmi";
+ clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
+ clock-names = "fck", "sys_clk";
+ };
+};
+
+A shortened example of the board description for OMAP4 Panda board, defined in
+omap4-panda.dts.
+
+The Panda board has a DVI and a HDMI connector, and the board contains a TFP410
+chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level
+shifter). The video pipelines for the connectors are formed as follows:
+
+DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector
+OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector
+
+/ {
+ aliases {
+ display0 = &dvi0;
+ display1 = &hdmi0;
+ };
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ port {
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+ };
+
+ tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+ };
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ port {
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+ };
+};
--- /dev/null
+Texas Instruments OMAP2 Display Subsystem
+=========================================
+
+See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap2-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Optional nodes:
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap2-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap2-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap2-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+VENC Endpoint required properties:
+
+Required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
--- /dev/null
+Texas Instruments OMAP3 Display Subsystem
+=========================================
+
+See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap3-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+- clocks: handle to fclk
+- clock-names: "fck"
+
+Optional nodes:
+- Video ports:
+ - Port 0: DPI output
+ - Port 1: SDI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+SDI Endpoint required properties:
+- datapairs: number of datapairs used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap3-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+- clocks: handle to fclk
+- clock-names: "fck"
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap3-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+- clocks: handles to fclk and iclk
+- clock-names: "fck", "ick"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap3-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+- clocks: handle to fclk
+- clock-names: "fck"
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap3-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1"
+- vdd-supply: power supply for DSI
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
--- /dev/null
+Texas Instruments OMAP4 Display Subsystem
+=========================================
+
+See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap4-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+- clocks: handle to fclk
+- clock-names: "fck"
+
+Required nodes:
+- DISPC
+
+Optional nodes:
+- DSS Submodules: RFBI, VENC, DSI, HDMI
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap4-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+- clocks: handle to fclk
+- clock-names: "fck"
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap4-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+- clocks: handles to fclk and iclk
+- clock-names: "fck", "ick"
+
+Optional nodes:
+- Video port for RFBI output
+- RFBI controlled peripherals
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap4-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+- clocks: handle to fclk
+- clock-names: "fck"
+
+Optional nodes:
+- Video port for VENC output
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap4-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1" or "dss_dsi2"
+- vdd-supply: power supply for DSI
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+Optional nodes:
+- Video port for DSI output
+- DSI controlled peripherals
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
+
+
+HDMI
+----
+
+Required properties:
+- compatible: "ti,omap4-hdmi"
+- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
+ 'core'
+- reg-names: "wp", "pll", "phy", "core"
+- interrupts: the HDMI interrupt line
+- ti,hwmods: "dss_hdmi"
+- vdda-supply: vdda power supply
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+Optional nodes:
+- Video port for HDMI output
+
+HDMI Endpoint optional properties:
+- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
+ D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
--- /dev/null
+Texas Instruments OMAP5 Display Subsystem
+=========================================
+
+See Documentation/devicetree/bindings/display/ti/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap5-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+- clocks: handle to fclk
+- clock-names: "fck"
+
+Required nodes:
+- DISPC
+
+Optional nodes:
+- DSS Submodules: RFBI, DSI, HDMI
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap5-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+- clocks: handle to fclk
+- clock-names: "fck"
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap5-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+- clocks: handles to fclk and iclk
+- clock-names: "fck", "ick"
+
+Optional nodes:
+- Video port for RFBI output
+- RFBI controlled peripherals
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap5-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1" or "dss_dsi2"
+- vdd-supply: power supply for DSI
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+Optional nodes:
+- Video port for DSI output
+- DSI controlled peripherals
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
+
+
+HDMI
+----
+
+Required properties:
+- compatible: "ti,omap5-hdmi"
+- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
+ 'core'
+- reg-names: "wp", "pll", "phy", "core"
+- interrupts: the HDMI interrupt line
+- ti,hwmods: "dss_hdmi"
+- vdda-supply: vdda power supply
+- clocks: handles to fclk and pll clock
+- clock-names: "fck", "sys_clk"
+
+Optional nodes:
+- Video port for HDMI output
+
+HDMI Endpoint optional properties:
+- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
+ D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
--- /dev/null
+OPA362 analog video amplifier
+
+Required properties:
+- compatible: "ti,opa362"
+- enable-gpios: enable/disable output gpio
+
+Required node:
+- Video port 0 for opa362 input
+- Video port 1 for opa362 output
+
+Example:
+
+tv_amp: opa362 {
+ compatible = "ti,opa362";
+ enable-gpios = <&gpio1 23 0>; /* GPIO to enable video out amplifier */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ opa_in: endpoint@0 {
+ remote-endpoint = <&venc_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ opa_out: endpoint@0 {
+ remote-endpoint = <&tv_connector_in>;
+ };
+ };
+ };
+};
+
+
+
--- /dev/null
+TFP410 DPI to DVI encoder
+=========================
+
+Required properties:
+- compatible: "ti,tfp410"
+
+Optional properties:
+- powerdown-gpios: power-down gpio
+
+Required nodes:
+- Video port 0 for DPI input
+- Video port 1 for DVI output
+
+Example
+-------
+
+tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+};
--- /dev/null
+TPD12S015 HDMI level shifter and ESD protection chip
+====================================================
+
+Required properties:
+- compatible: "ti,tpd12s015"
+
+Optional properties:
+- gpios: CT CP HPD, LS OE and HPD gpios
+
+Required nodes:
+- Video port 0 for HDMI input
+- Video port 1 for HDMI output
+
+Example
+-------
+
+tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+};
--- /dev/null
+Device-Tree bindings for tilcdc DRM generic panel output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,panel".
+ - panel-info: configuration info to configure LCDC correctly for the panel
+ - ac-bias: AC Bias Pin Frequency
+ - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
+ - dma-burst-sz: DMA burst size
+ - bpp: Bits per pixel
+ - fdd: FIFO DMA Request Delay
+ - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
+ - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
+ - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
+ - fifo-th: DMA FIFO threshold
+ - display-timings: typical videomode of lcd panel. Multiple video modes
+ can be listed if the panel supports multiple timings, but the 'native-mode'
+ should be the preferred/default resolution. Refer to
+ Documentation/devicetree/bindings/display/display-timing.txt for display
+ timing binding details.
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+- enable-gpios: GPIO pin to enable or disable the panel
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+
+Example:
+
+ /* Settings for CDTech_S035Q01 / LCD3 cape: */
+ lcd3 {
+ compatible = "ti,tilcdc,panel";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio3 19 0>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <16>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 320x240 {
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <21>;
+ hfront-porch = <58>;
+ hsync-len = <47>;
+ vback-porch = <11>;
+ vfront-porch = <23>;
+ vsync-len = <2>;
+ clock-frequency = <8000000>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ };
+ };
+ };
--- /dev/null
+Device-Tree bindings for tilcdc DRM TFP410 output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,tfp410".
+ - i2c: the phandle for the i2c device to use for DDC
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+ - powerdn-gpio: the powerdown GPIO, pulled low to power down the
+ TFP410 device (for DPMS_OFF)
+
+Example:
+
+ dvicape {
+ compatible = "ti,tilcdc,tfp410";
+ i2c = <&i2c2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
+ powerdn-gpio = <&gpio2 31 0>;
+ };
--- /dev/null
+Device-Tree bindings for tilcdc DRM driver
+
+Required properties:
+ - compatible: value should be "ti,am33xx-tilcdc".
+ - interrupts: the interrupt number
+ - reg: base address and size of the LCDC device
+
+Recommended properties:
+ - interrupt-parent: the phandle for the interrupt controller that
+ services interrupts for this device.
+ - ti,hwmods: Name of the hwmod associated to the LCDC
+
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+ interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+ the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+ by the lcd controller in KHz.
+
+Optional nodes:
+
+ - port/ports: to describe a connection to an external encoder. The
+ binding follows Documentation/devicetree/bindings/graph.txt and
+ suppors a single port with a single endpoint.
+
+Example:
+
+ fb: fb@4830e000 {
+ compatible = "ti,am33xx-tilcdc";
+ reg = <0x4830e000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+ ti,hwmods = "lcdc";
+
+ port {
+ lcdc_0: endpoint@0 {
+ remote-endpoint = <&hdmi_0>;
+ };
+ };
+ };
+
+ tda19988: tda19988 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+ port {
+ hdmi_0: endpoint@0 {
+ remote-endpoint = <&lcdc_0>;
+ };
+ };
+ };
--- /dev/null
+VIA VT8500 Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible : "via,vt8500-fb"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : framebuffer controller interrupt
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
+
+Required subnodes:
+- display-timings: see display-timing.txt for information
+
+Example:
+
+ fb@d8050800 {
+ compatible = "via,vt8500-fb";
+ reg = <0xd800e400 0x400>;
+ interrupts = <12>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <40>;
+ hback-porch = <88>;
+ hsync-len = <0>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <1>;
+ };
+ };
+ };
+
--- /dev/null
+VIA/Wondermedia Graphics Engine Controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : "wm,prizm-ge-rops"
+- reg : Should contain 1 register ranges(address and length)
+
+Example:
+
+ ge_rops@d8050400 {
+ compatible = "wm,prizm-ge-rops";
+ reg = <0xd8050400 0x100>;
+ };
--- /dev/null
+Wondermedia WM8505 Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible : "wm,wm8505-fb"
+- reg : Should contain 1 register ranges(address and length)
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
+
+Required subnodes:
+- display-timings: see display-timing.txt for information
+
+Example:
+
+ fb@d8051700 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8051700 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <40>;
+ hback-porch = <88>;
+ hsync-len = <0>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <1>;
+ };
+ };
+ };
+++ /dev/null
-Device Tree bindings for Armada DRM CRTC driver
-
-Required properties:
- - compatible: value should be "marvell,dove-lcd".
- - reg: base address and size of the LCD controller
- - interrupts: single interrupt number for the LCD controller
- - port: video output port with endpoints, as described by graph.txt
-
-Optional properties:
-
- - clocks: as described by clock-bindings.txt
- - clock-names: as described by clock-bindings.txt
- "axiclk" - axi bus clock for pixel clock
- "plldivider" - pll divider clock for pixel clock
- "ext_ref_clk0" - external clock 0 for pixel clock
- "ext_ref_clk1" - external clock 1 for pixel clock
-
-Note: all clocks are optional but at least one must be specified.
-Further clocks may be added in the future according to requirements of
-different SoCs.
-
-Example:
-
- lcd0: lcd-controller@820000 {
- compatible = "marvell,dove-lcd";
- reg = <0x820000 0x1000>;
- interrupts = <47>;
- clocks = <&si5351 0>;
- clock-names = "ext_ref_clk_1";
- };
+++ /dev/null
-Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver
-
-The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device.
-See ../mfd/atmel-hlcdc.txt for more details.
-
-Required properties:
- - compatible: value should be "atmel,hlcdc-display-controller"
- - pinctrl-names: the pin control state names. Should contain "default".
- - pinctrl-0: should contain the default pinctrl states.
- - #address-cells: should be set to 1.
- - #size-cells: should be set to 0.
-
-Required children nodes:
- Children nodes are encoding available output ports and their connections
- to external devices using the OF graph reprensentation (see ../graph.txt).
- At least one port node is required.
-
-Example:
-
- hlcdc: hlcdc@f0030000 {
- compatible = "atmel,sama5d3-hlcdc";
- reg = <0xf0030000 0x2000>;
- interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
- clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
- clock-names = "periph_clk","sys_clk", "slow_clk";
- status = "disabled";
-
- hlcdc-display-controller {
- compatible = "atmel,hlcdc-display-controller";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- hlcdc_panel_output: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&panel_input>;
- };
- };
- };
-
- hlcdc_pwm: hlcdc-pwm {
- compatible = "atmel,hlcdc-pwm";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd_pwm>;
- #pwm-cells = <3>;
- };
- };
+++ /dev/null
-DesignWare HDMI bridge bindings
-
-Required properties:
-- compatible: platform specific such as:
- * "snps,dw-hdmi-tx"
- * "fsl,imx6q-hdmi"
- * "fsl,imx6dl-hdmi"
- * "rockchip,rk3288-dw-hdmi"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The HDMI interrupt number
-- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
- as described in Documentation/devicetree/bindings/clock/clock-bindings.txt,
- the clocks are soc specific, the clock-names should be "iahb", "isfr"
--port@[X]: SoC specific port nodes with endpoint definitions as defined
- in Documentation/devicetree/bindings/media/video-interfaces.txt,
- please refer to the SoC specific binding document:
- * Documentation/devicetree/bindings/drm/imx/hdmi.txt
- * Documentation/devicetree/bindings/video/dw_hdmi-rockchip.txt
-
-Optional properties
-- reg-io-width: the width of the reg:1,4, default set to 1 if not present
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
-
-Example:
- hdmi: hdmi@0120000 {
- compatible = "fsl,imx6q-hdmi";
- reg = <0x00120000 0x9000>;
- interrupts = <0 115 0x04>;
- gpr = <&gpr>;
- clocks = <&clks 123>, <&clks 124>;
- clock-names = "iahb", "isfr";
- ddc-i2c-bus = <&i2c2>;
-
- port@0 {
- reg = <0>;
-
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
- };
- };
- };
+++ /dev/null
-Device-Tree bindings for the NXP TDA998x HDMI transmitter
-
-Required properties;
- - compatible: must be "nxp,tda998x"
-
- - reg: I2C address
-
-Optional properties:
- - interrupts: interrupt number and trigger type
- default: polling
-
- - pinctrl-0: pin control group to be used for
- screen plug/unplug interrupt.
-
- - pinctrl-names: must contain a "default" entry.
-
- - video-ports: 24 bits value which defines how the video controller
- output is wired to the TDA998x input - default: <0x230145>
-
-Example:
-
- tda998x: hdmi-encoder {
- compatible = "nxp,tda998x";
- reg = <0x70>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 2>; /* falling edge */
- pinctrl-0 = <&pmx_camera>;
- pinctrl-names = "default";
- };
+++ /dev/null
-Freescale i.MX DRM master device
-================================
-
-The freescale i.MX DRM master device is a virtual device needed to list all
-IPU or other display interface nodes that comprise the graphics subsystem.
-
-Required properties:
-- compatible: Should be "fsl,imx-display-subsystem"
-- ports: Should contain a list of phandles pointing to display interface ports
- of IPU devices
-
-example:
-
-display-subsystem {
- compatible = "fsl,display-subsystem";
- ports = <&ipu_di0>;
-};
-
-
-Freescale i.MX IPUv3
-====================
-
-Required properties:
-- compatible: Should be "fsl,<chip>-ipu"
-- reg: should be register base and length as documented in the
- datasheet
-- interrupts: Should contain sync interrupt and error interrupt,
- in this order.
-- resets: phandle pointing to the system reset controller and
- reset line index, see reset/fsl,imx-src.txt for details
-Optional properties:
-- port@[0-3]: Port nodes with endpoint definitions as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt.
- Ports 0 and 1 should correspond to CSI0 and CSI1,
- ports 2 and 3 should correspond to DI0 and DI1, respectively.
-
-example:
-
-ipu: ipu@18000000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx53-ipu";
- reg = <0x18000000 0x080000000>;
- interrupts = <11 10>;
- resets = <&src 2>;
-
- ipu_di0: port@2 {
- reg = <2>;
-
- ipu_di0_disp0: endpoint {
- remote-endpoint = <&display_in>;
- };
- };
-};
-
-Parallel display support
-========================
-
-Required properties:
-- compatible: Should be "fsl,imx-parallel-display"
-Optional properties:
-- interface_pix_fmt: How this display is connected to the
- display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
- and "lvds666".
-- edid: verbatim EDID data block describing attached display.
-- ddc: phandle describing the i2c bus handling the display data
- channel
-- port@[0-1]: Port nodes with endpoint definitions as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt.
- Port 0 is the input port connected to the IPU display interface,
- port 1 is the output port connected to a panel.
-
-example:
-
-display@di0 {
- compatible = "fsl,imx-parallel-display";
- edid = [edid-data];
- interface-pix-fmt = "rgb24";
-
- port@0 {
- reg = <0>;
-
- display_in: endpoint {
- remote-endpoint = <&ipu_di0_disp0>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-};
-
-panel {
- ...
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&display_out>;
- };
- };
-};
+++ /dev/null
-Device-Tree bindings for HDMI Transmitter
-
-HDMI Transmitter
-================
-
-The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with accompanying PHY IP.
-
-Required properties:
- - #address-cells : should be <1>
- - #size-cells : should be <0>
- - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
- - gpr : should be <&gpr>.
- The phandle points to the iomuxc-gpr region containing the HDMI
- multiplexer control register.
- - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
- in Documentation/devicetree/bindings/clock/clock-bindings.txt and
- Documentation/devicetree/bindings/clock/imx6q-clock.txt.
- - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt,
- corresponding to the four inputs to the HDMI multiplexer.
-
-Optional properties:
- - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-
-example:
-
- gpr: iomuxc-gpr@020e0000 {
- /* ... */
- };
-
- hdmi: hdmi@0120000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6q-hdmi";
- reg = <0x00120000 0x9000>;
- interrupts = <0 115 0x04>;
- gpr = <&gpr>;
- clocks = <&clks 123>, <&clks 124>;
- clock-names = "iahb", "isfr";
- ddc-i2c-bus = <&i2c2>;
-
- port@0 {
- reg = <0>;
-
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
- };
- };
- };
+++ /dev/null
-Device-Tree bindings for LVDS Display Bridge (ldb)
-
-LVDS Display Bridge
-===================
-
-The LVDS Display Bridge device tree node contains up to two lvds-channel
-nodes describing each of the two LVDS encoder channels of the bridge.
-
-Required properties:
- - #address-cells : should be <1>
- - #size-cells : should be <0>
- - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
- Both LDB versions are similar, but i.MX6 has an additional
- multiplexer in the front to select any of the four IPU display
- interfaces as input for each LVDS channel.
- - gpr : should be <&gpr> on i.MX53 and i.MX6q.
- The phandle points to the iomuxc-gpr region containing the LVDS
- control register.
-- clocks, clock-names : phandles to the LDB divider and selector clocks and to
- the display interface selector clocks, as described in
- Documentation/devicetree/bindings/clock/clock-bindings.txt
- The following clocks are expected on i.MX53:
- "di0_pll" - LDB LVDS channel 0 mux
- "di1_pll" - LDB LVDS channel 1 mux
- "di0" - LDB LVDS channel 0 gate
- "di1" - LDB LVDS channel 1 gate
- "di0_sel" - IPU1 DI0 mux
- "di1_sel" - IPU1 DI1 mux
- On i.MX6q the following additional clocks are needed:
- "di2_sel" - IPU2 DI0 mux
- "di3_sel" - IPU2 DI1 mux
- The needed clock numbers for each are documented in
- Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
- Documentation/devicetree/bindings/clock/imx6q-clock.txt.
-
-Optional properties:
- - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
- - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
- not used on i.MX6q
- - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
- be configured - one input will be distributed on both outputs in dual
- channel mode
-
-LVDS Channel
-============
-
-Each LVDS Channel has to contain either an of graph link to a panel device node
-or a display-timings node that describes the video timings for the connected
-LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
-
-Required properties:
- - reg : should be <0> or <1>
- - port: Input and output port nodes with endpoint definitions as defined in
- Documentation/devicetree/bindings/graph.txt.
- On i.MX5, the internal two-input-multiplexer is used. Due to hardware
- limitations, only one input port (port@[0,1]) can be used for each channel
- (lvds-channel@[0,1], respectively).
- On i.MX6, there should be four input ports (port@[0-3]) that correspond
- to the four LVDS multiplexer inputs.
- A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
- to a panel input port. Optionally, the output port can be left out if
- display-timings are used instead.
-
-Optional properties (required if display-timings are used):
- - display-timings : A node that describes the display timings as defined in
- Documentation/devicetree/bindings/video/display-timing.txt.
- - fsl,data-mapping : should be "spwg" or "jeida"
- This describes how the color bits are laid out in the
- serialized LVDS signal.
- - fsl,data-width : should be <18> or <24>
-
-example:
-
-gpr: iomuxc-gpr@53fa8000 {
- /* ... */
-};
-
-ldb: ldb@53fa8008 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx53-ldb";
- gpr = <&gpr>;
- clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
- <&clks IMX5_CLK_LDB_DI1_SEL>,
- <&clks IMX5_CLK_IPU_DI0_SEL>,
- <&clks IMX5_CLK_IPU_DI1_SEL>,
- <&clks IMX5_CLK_LDB_DI0_GATE>,
- <&clks IMX5_CLK_LDB_DI1_GATE>;
- clock-names = "di0_pll", "di1_pll",
- "di0_sel", "di1_sel",
- "di0", "di1";
-
- /* Using an of-graph endpoint link to connect the panel */
- lvds-channel@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- port@0 {
- reg = <0>;
-
- lvds0_in: endpoint {
- remote-endpoint = <&ipu_di0_lvds0>;
- };
- };
-
- port@2 {
- reg = <2>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-
- /* Using display-timings and fsl,data-mapping/width instead */
- lvds-channel@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
- fsl,data-mapping = "spwg";
- fsl,data-width = <24>;
-
- display-timings {
- /* ... */
- };
-
- port@1 {
- reg = <1>;
-
- lvds1_in: endpoint {
- remote-endpoint = <&ipu_di1_lvds1>;
- };
- };
- };
-};
-
-panel: lvds-panel {
- /* ... */
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
-};
+++ /dev/null
-Qualcomm Technologies Inc. adreno/snapdragon DSI output
-
-DSI Controller:
-Required properties:
-- compatible:
- * "qcom,mdss-dsi-ctrl"
-- reg: Physical base address and length of the registers of controller
-- reg-names: The names of register regions. The following regions are required:
- * "dsi_ctrl"
-- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should
- be 0 or 1, since we have 2 DSI controllers at most for now.
-- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: device clocks
- See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
- * "bus_clk"
- * "byte_clk"
- * "core_clk"
- * "core_mmss_clk"
- * "iface_clk"
- * "mdp_core_clk"
- * "pixel_clk"
-- vdd-supply: phandle to vdd regulator device node
-- vddio-supply: phandle to vdd-io regulator device node
-- vdda-supply: phandle to vdda regulator device node
-- qcom,dsi-phy: phandle to DSI PHY device node
-
-Optional properties:
-- panel@0: Node of panel connected to this DSI controller.
- See files in Documentation/devicetree/bindings/panel/ for each supported
- panel.
-- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
- driving a panel which needs 2 DSI links.
-- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
- the master link of the 2-DSI panel.
-- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
- driving a 2-DSI panel whose 2 links need receive command simultaneously.
-- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
- through MDP block
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-n: the "sleep" pinctrl state
-- port: DSI controller output port. This contains one endpoint subnode, with its
- remote-endpoint set to the phandle of the connected panel's endpoint.
- See Documentation/devicetree/bindings/graph.txt for device graph info.
-
-DSI PHY:
-Required properties:
-- compatible: Could be the following
- * "qcom,dsi-phy-28nm-hpm"
- * "qcom,dsi-phy-28nm-lp"
- * "qcom,dsi-phy-20nm"
-- reg: Physical base address and length of the registers of PLL, PHY and PHY
- regulator
-- reg-names: The names of register regions. The following regions are required:
- * "dsi_pll"
- * "dsi_phy"
- * "dsi_phy_regulator"
-- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should
- be 0 or 1, since we have 2 DSI PHYs at most for now.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: device clocks
- See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
- * "iface_clk"
-- vddio-supply: phandle to vdd-io regulator device node
-
-Optional properties:
-- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
- regulator is wanted.
-
-Example:
- mdss_dsi0: qcom,mdss_dsi@fd922800 {
- compatible = "qcom,mdss-dsi-ctrl";
- qcom,dsi-host-index = <0>;
- interrupt-parent = <&mdss_mdp>;
- interrupts = <4 0>;
- reg-names = "dsi_ctrl";
- reg = <0xfd922800 0x200>;
- power-domains = <&mmcc MDSS_GDSC>;
- clock-names =
- "bus_clk",
- "byte_clk",
- "core_clk",
- "core_mmss_clk",
- "iface_clk",
- "mdp_core_clk",
- "pixel_clk";
- clocks =
- <&mmcc MDSS_AXI_CLK>,
- <&mmcc MDSS_BYTE0_CLK>,
- <&mmcc MDSS_ESC0_CLK>,
- <&mmcc MMSS_MISC_AHB_CLK>,
- <&mmcc MDSS_AHB_CLK>,
- <&mmcc MDSS_MDP_CLK>,
- <&mmcc MDSS_PCLK0_CLK>;
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
-
- qcom,dsi-phy = <&mdss_dsi_phy0>;
-
- qcom,dual-dsi-mode;
- qcom,master-dsi;
- qcom,sync-dual-dsi;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mdss_dsi_active>;
- pinctrl-1 = <&mdss_dsi_suspend>;
-
- panel: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
- link2 = <&secondary>;
-
- power-supply = <...>;
- backlight = <...>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
-
- port {
- dsi0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-
- mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 {
- compatible = "qcom,dsi-phy-28nm-hpm";
- qcom,dsi-phy-index = <0>;
- reg-names =
- "dsi_pll",
- "dsi_phy",
- "dsi_phy_regulator";
- reg = <0xfd922a00 0xd4>,
- <0xfd922b00 0x2b0>,
- <0xfd922d80 0x7b>;
- clock-names = "iface_clk";
- clocks = <&mmcc MDSS_AHB_CLK>;
- vddio-supply = <&pma8084_l12>;
-
- qcom,dsi-phy-regulator-ldo-mode;
- };
+++ /dev/null
-Qualcomm Technologies Inc. adreno/snapdragon eDP output
-
-Required properties:
-- compatible:
- * "qcom,mdss-edp"
-- reg: Physical base address and length of the registers of controller and PLL
-- reg-names: The names of register regions. The following regions are required:
- * "edp"
- * "pll_base"
-- interrupts: The interrupt signal from the eDP block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
-- clocks: device clocks
- See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
- * "core_clk"
- * "iface_clk"
- * "mdp_core_clk"
- * "pixel_clk"
- * "link_clk"
-- #clock-cells: The value should be 1.
-- vdda-supply: phandle to vdda regulator device node
-- lvl-vdd-supply: phandle to regulator device node which is used to supply power
- to HPD receiving chip
-- panel-en-gpios: GPIO pin to supply power to panel.
-- panel-hpd-gpios: GPIO pin used for eDP hpd.
-
-
-Optional properties:
-- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
- through MDP block
-
-Example:
- mdss_edp: qcom,mdss_edp@fd923400 {
- compatible = "qcom,mdss-edp";
- reg-names =
- "edp",
- "pll_base";
- reg = <0xfd923400 0x700>,
- <0xfd923a00 0xd4>;
- interrupt-parent = <&mdss_mdp>;
- interrupts = <12 0>;
- power-domains = <&mmcc MDSS_GDSC>;
- clock-names =
- "core_clk",
- "pixel_clk",
- "iface_clk",
- "link_clk",
- "mdp_core_clk";
- clocks =
- <&mmcc MDSS_EDPAUX_CLK>,
- <&mmcc MDSS_EDPPIXEL_CLK>,
- <&mmcc MDSS_AHB_CLK>,
- <&mmcc MDSS_EDPLINK_CLK>,
- <&mmcc MDSS_MDP_CLK>;
- #clock-cells = <1>;
- vdda-supply = <&pma8084_l12>;
- lvl-vdd-supply = <&lvl_vreg>;
- panel-en-gpios = <&tlmm 137 0>;
- panel-hpd-gpios = <&tlmm 103 0>;
- };
+++ /dev/null
-Qualcomm adreno/snapdragon GPU
-
-Required properties:
-- compatible: "qcom,adreno-3xx"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt signal from the gpu.
-- clocks: device clocks
- See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
- * "core_clk"
- * "iface_clk"
- * "mem_iface_clk"
-- qcom,chipid: gpu chip-id. Note this may become optional for future
- devices if we can reliably read the chipid from hw
-- qcom,gpu-pwrlevels: list of operating points
- - compatible: "qcom,gpu-pwrlevels"
- - for each qcom,gpu-pwrlevel:
- - qcom,gpu-freq: requested gpu clock speed
- - NOTE: downstream android driver defines additional parameters to
- configure memory bandwidth scaling per OPP.
-
-Example:
-
-/ {
- ...
-
- gpu: qcom,kgsl-3d0@4300000 {
- compatible = "qcom,adreno-3xx";
- reg = <0x04300000 0x20000>;
- reg-names = "kgsl_3d0_reg_memory";
- interrupts = <GIC_SPI 80 0>;
- interrupt-names = "kgsl_3d0_irq";
- clock-names =
- "core_clk",
- "iface_clk",
- "mem_iface_clk";
- clocks =
- <&mmcc GFX3D_CLK>,
- <&mmcc GFX3D_AHB_CLK>,
- <&mmcc MMSS_IMEM_AHB_CLK>;
- qcom,chipid = <0x03020100>;
- qcom,gpu-pwrlevels {
- compatible = "qcom,gpu-pwrlevels";
- qcom,gpu-pwrlevel@0 {
- qcom,gpu-freq = <450000000>;
- };
- qcom,gpu-pwrlevel@1 {
- qcom,gpu-freq = <27000000>;
- };
- };
- };
-};
+++ /dev/null
-Qualcomm adreno/snapdragon hdmi output
-
-Required properties:
-- compatible: one of the following
- * "qcom,hdmi-tx-8994"
- * "qcom,hdmi-tx-8084"
- * "qcom,hdmi-tx-8974"
- * "qcom,hdmi-tx-8660"
- * "qcom,hdmi-tx-8960"
-- reg: Physical base address and length of the controller's registers
-- reg-names: "core_physical"
-- interrupts: The interrupt signal from the hdmi block.
-- clocks: device clocks
- See ../clocks/clock-bindings.txt for details.
-- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
-- qcom,hdmi-tx-ddc-data-gpio: ddc data pin
-- qcom,hdmi-tx-hpd-gpio: hpd pin
-- core-vdda-supply: phandle to supply regulator
-- hdmi-mux-supply: phandle to mux regulator
-
-Optional properties:
-- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
-- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
-- pinctrl-names: the pin control state names; should contain "default"
-- pinctrl-0: the default pinctrl state (active)
-- pinctrl-1: the "sleep" pinctrl state
-
-Example:
-
-/ {
- ...
-
- hdmi: qcom,hdmi-tx-8960@4a00000 {
- compatible = "qcom,hdmi-tx-8960";
- reg-names = "core_physical";
- reg = <0x04a00000 0x1000>;
- interrupts = <GIC_SPI 79 0>;
- clock-names =
- "core_clk",
- "master_iface_clk",
- "slave_iface_clk";
- clocks =
- <&mmcc HDMI_APP_CLK>,
- <&mmcc HDMI_M_AHB_CLK>,
- <&mmcc HDMI_S_AHB_CLK>;
- qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>;
- qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>;
- qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
- core-vdda-supply = <&pm8921_hdmi_mvs>;
- hdmi-mux-supply = <&ext_3p3v>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&hpd_active &ddc_active &cec_active>;
- pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
- };
-};
+++ /dev/null
-Qualcomm adreno/snapdragon display controller
-
-Required properties:
-- compatible:
- * "qcom,mdp" - mdp4
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt signal from the display controller.
-- connectors: array of phandles for output device(s)
-- clocks: device clocks
- See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
- * "core_clk"
- * "iface_clk"
- * "lut_clk"
- * "src_clk"
- * "hdmi_clk"
- * "mpd_clk"
-
-Optional properties:
-- gpus: phandle for gpu device
-
-Example:
-
-/ {
- ...
-
- mdp: qcom,mdp@5100000 {
- compatible = "qcom,mdp";
- reg = <0x05100000 0xf0000>;
- interrupts = <GIC_SPI 75 0>;
- connectors = <&hdmi>;
- gpus = <&gpu>;
- clock-names =
- "core_clk",
- "iface_clk",
- "lut_clk",
- "src_clk",
- "hdmi_clk",
- "mdp_clk";
- clocks =
- <&mmcc MDP_SRC>,
- <&mmcc MDP_AHB_CLK>,
- <&mmcc MDP_LUT_CLK>,
- <&mmcc TV_SRC>,
- <&mmcc HDMI_TV_CLK>,
- <&mmcc MDP_TV_CLK>;
- };
-};
+++ /dev/null
-Device-Tree bindings for tilcdc DRM generic panel output driver
-
-Required properties:
- - compatible: value should be "ti,tilcdc,panel".
- - panel-info: configuration info to configure LCDC correctly for the panel
- - ac-bias: AC Bias Pin Frequency
- - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
- - dma-burst-sz: DMA burst size
- - bpp: Bits per pixel
- - fdd: FIFO DMA Request Delay
- - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
- - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
- - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
- - fifo-th: DMA FIFO threshold
- - display-timings: typical videomode of lcd panel. Multiple video modes
- can be listed if the panel supports multiple timings, but the 'native-mode'
- should be the preferred/default resolution. Refer to
- Documentation/devicetree/bindings/video/display-timing.txt for display
- timing binding details.
-
-Optional properties:
-- backlight: phandle of the backlight device attached to the panel
-- enable-gpios: GPIO pin to enable or disable the panel
-
-Recommended properties:
- - pinctrl-names, pinctrl-0: the pincontrol settings to configure
- muxing properly for pins that connect to TFP410 device
-
-Example:
-
- /* Settings for CDTech_S035Q01 / LCD3 cape: */
- lcd3 {
- compatible = "ti,tilcdc,panel";
- pinctrl-names = "default";
- pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
- backlight = <&backlight>;
- enable-gpios = <&gpio3 19 0>;
-
- panel-info {
- ac-bias = <255>;
- ac-bias-intrpt = <0>;
- dma-burst-sz = <16>;
- bpp = <16>;
- fdd = <0x80>;
- sync-edge = <0>;
- sync-ctrl = <1>;
- raster-order = <0>;
- fifo-th = <0>;
- };
- display-timings {
- native-mode = <&timing0>;
- timing0: 320x240 {
- hactive = <320>;
- vactive = <240>;
- hback-porch = <21>;
- hfront-porch = <58>;
- hsync-len = <47>;
- vback-porch = <11>;
- vfront-porch = <23>;
- vsync-len = <2>;
- clock-frequency = <8000000>;
- hsync-active = <0>;
- vsync-active = <0>;
- };
- };
- };
+++ /dev/null
-Device-Tree bindings for tilcdc DRM TFP410 output driver
-
-Required properties:
- - compatible: value should be "ti,tilcdc,tfp410".
- - i2c: the phandle for the i2c device to use for DDC
-
-Recommended properties:
- - pinctrl-names, pinctrl-0: the pincontrol settings to configure
- muxing properly for pins that connect to TFP410 device
- - powerdn-gpio: the powerdown GPIO, pulled low to power down the
- TFP410 device (for DPMS_OFF)
-
-Example:
-
- dvicape {
- compatible = "ti,tilcdc,tfp410";
- i2c = <&i2c2>;
- pinctrl-names = "default";
- pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
- powerdn-gpio = <&gpio2 31 0>;
- };
+++ /dev/null
-Device-Tree bindings for tilcdc DRM driver
-
-Required properties:
- - compatible: value should be "ti,am33xx-tilcdc".
- - interrupts: the interrupt number
- - reg: base address and size of the LCDC device
-
-Recommended properties:
- - interrupt-parent: the phandle for the interrupt controller that
- services interrupts for this device.
- - ti,hwmods: Name of the hwmod associated to the LCDC
-
-Optional properties:
- - max-bandwidth: The maximum pixels per second that the memory
- interface / lcd controller combination can sustain
- - max-width: The maximum horizontal pixel width supported by
- the lcd controller.
- - max-pixelclock: The maximum pixel clock that can be supported
- by the lcd controller in KHz.
-
-Optional nodes:
-
- - port/ports: to describe a connection to an external encoder. The
- binding follows Documentation/devicetree/bindings/graph.txt and
- suppors a single port with a single endpoint.
-
-Example:
-
- fb: fb@4830e000 {
- compatible = "ti,am33xx-tilcdc";
- reg = <0x4830e000 0x1000>;
- interrupt-parent = <&intc>;
- interrupts = <36>;
- ti,hwmods = "lcdc";
-
- port {
- lcdc_0: endpoint@0 {
- remote-endpoint = <&hdmi_0>;
- };
- };
- };
-
- tda19988: tda19988 {
- compatible = "nxp,tda998x";
- reg = <0x70>;
-
- pinctrl-names = "default", "off";
- pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
- pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
- port {
- hdmi_0: endpoint@0 {
- remote-endpoint = <&lcdc_0>;
- };
- };
- };
+++ /dev/null
-* Freescale MXS LCD Interface (LCDIF)
-
-Required properties:
-- compatible: Should be "fsl,<chip>-lcdif". Supported chips include
- imx23 and imx28.
-- reg: Address and length of the register set for lcdif
-- interrupts: Should contain lcdif interrupts
-- display : phandle to display node (see below for details)
-
-* display node
-
-Required properties:
-- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
-- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>.
-
-Required sub-node:
-- display-timings : Refer to binding doc display-timing.txt for details.
-
-Examples:
-
-lcdif@80030000 {
- compatible = "fsl,imx28-lcdif";
- reg = <0x80030000 2000>;
- interrupts = <38 86>;
-
- display: display {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hfront-porch = <164>;
- hback-porch = <89>;
- hsync-len = <10>;
- vback-porch = <23>;
- vfront-porch = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
-};
+++ /dev/null
-* SM SM501
-
-The SM SM501 is a LCD controller, with proper hardware, it can also
-drive DVI monitors.
-
-Required properties:
-- compatible : should be "smi,sm501".
-- reg : contain two entries:
- - First entry: System Configuration register
- - Second entry: IO space (Display Controller register)
-- interrupts : SMI interrupt to the cpu should be described here.
-- interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
-Optional properties:
-- mode : select a video mode:
- <xres>x<yres>[-<bpp>][@<refresh>]
-- edid : verbatim EDID data block describing attached display.
- Data from the detailed timing descriptor will be used to
- program the display controller.
-- little-endian: available on big endian systems, to
- set different foreign endian.
-- big-endian: available on little endian systems, to
- set different foreign endian.
-
-Example for MPC5200:
- display@1,0 {
- compatible = "smi,sm501";
- reg = <1 0x00000000 0x00800000
- 1 0x03e00000 0x00200000>;
- interrupts = <1 1 3>;
- mode = "640x480-32@60";
- edid = [edid-data];
- };
+++ /dev/null
-NVIDIA Tegra host1x
-
-Required properties:
-- compatible: "nvidia,tegra<chip>-host1x"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt outputs from the controller.
-- #address-cells: The number of cells used to represent physical base addresses
- in the host1x address space. Should be 1.
-- #size-cells: The number of cells used to represent the size of an address
- range in the host1x address space. Should be 1.
-- ranges: The mapping of the host1x address space to the CPU address space.
-- clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names: Must include the following entries:
- - host1x
-
-The host1x top-level node defines a number of children, each representing one
-of the following host1x client modules:
-
-- mpe: video encoder
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-mpe"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - mpe
-
-- vi: video input
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-vi"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - vi
-
-- epp: encoder pre-processor
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-epp"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - epp
-
-- isp: image signal processor
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-isp"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - isp
-
-- gr2d: 2D graphics engine
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-gr2d"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - 2d
-
-- gr3d: 3D graphics engine
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-gr3d"
- - reg: Physical base address and length of the controller's registers.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- (This property may be omitted if the only clock in the list is "3d")
- - 3d
- This MUST be the first entry.
- - 3d2 (Only required on SoCs with two 3D clocks)
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - 3d
- - 3d2 (Only required on SoCs with two 3D clocks)
-
-- dc: display controller
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-dc"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dc
- This MUST be the first entry.
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dc
- - nvidia,head: The number of the display controller head. This is used to
- setup the various types of output to receive video data from the given
- head.
-
- Each display controller node has a child node, named "rgb", that represents
- the RGB output associated with the controller. It can take the following
- optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
-
-- hdmi: High Definition Multimedia Interface
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-hdmi"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - hdmi-supply: supply for the +5V HDMI connector pin
- - vdd-supply: regulator for supply voltage
- - pll-supply: regulator for PLL
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - hdmi
- This MUST be the first entry.
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - hdmi
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
-
-- tvo: TV encoder output
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-tvo"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
-
-- dsi: display serial interface
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-dsi"
- - reg: Physical base address and length of the controller's registers.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dsi
- This MUST be the first entry.
- - lp
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dsi
- - avdd-dsi-supply: phandle of a supply that powers the DSI controller
- - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
- which pads are used by this DSI output and need to be calibrated. See also
- ../mipi/nvidia,tegra114-mipi.txt.
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
- - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang
- up with in order to support up to 8 data lanes
-
-- sor: serial output resource
-
- Required properties:
- - compatible: Should be:
- - "nvidia,tegra124-sor": for Tegra124 and Tegra132
- - "nvidia,tegra132-sor": for Tegra132
- - "nvidia,tegra210-sor": for Tegra210
- - "nvidia,tegra210-sor1": for Tegra210
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - sor: clock input for the SOR hardware
- - parent: input for the pixel clock
- - dp: reference clock for the SOR clock
- - safe: safe reference for the SOR clock during power up
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - sor
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
-
- Optional properties when driving an eDP output:
- - nvidia,dpaux: phandle to a DispayPort AUX interface
-
-- dpaux: DisplayPort AUX interface
- - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise,
- must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where
- <chip> is tegra132.
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dpaux: clock input for the DPAUX hardware
- - parent: reference clock
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dpaux
- - vdd-supply: phandle of a supply that powers the DisplayPort link
-
-Example:
-
-/ {
- ...
-
- host1x {
- compatible = "nvidia,tegra20-host1x", "simple-bus";
- reg = <0x50000000 0x00024000>;
- interrupts = <0 65 0x04 /* mpcore syncpt */
- 0 67 0x04>; /* mpcore general */
- clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
- resets = <&tegra_car 28>;
- reset-names = "host1x";
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- ranges = <0x54000000 0x54000000 0x04000000>;
-
- mpe {
- compatible = "nvidia,tegra20-mpe";
- reg = <0x54040000 0x00040000>;
- interrupts = <0 68 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_MPE>;
- resets = <&tegra_car 60>;
- reset-names = "mpe";
- };
-
- vi {
- compatible = "nvidia,tegra20-vi";
- reg = <0x54080000 0x00040000>;
- interrupts = <0 69 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_VI>;
- resets = <&tegra_car 100>;
- reset-names = "vi";
- };
-
- epp {
- compatible = "nvidia,tegra20-epp";
- reg = <0x540c0000 0x00040000>;
- interrupts = <0 70 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_EPP>;
- resets = <&tegra_car 19>;
- reset-names = "epp";
- };
-
- isp {
- compatible = "nvidia,tegra20-isp";
- reg = <0x54100000 0x00040000>;
- interrupts = <0 71 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_ISP>;
- resets = <&tegra_car 23>;
- reset-names = "isp";
- };
-
- gr2d {
- compatible = "nvidia,tegra20-gr2d";
- reg = <0x54140000 0x00040000>;
- interrupts = <0 72 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_GR2D>;
- resets = <&tegra_car 21>;
- reset-names = "2d";
- };
-
- gr3d {
- compatible = "nvidia,tegra20-gr3d";
- reg = <0x54180000 0x00040000>;
- clocks = <&tegra_car TEGRA20_CLK_GR3D>;
- resets = <&tegra_car 24>;
- reset-names = "3d";
- };
-
- dc@54200000 {
- compatible = "nvidia,tegra20-dc";
- reg = <0x54200000 0x00040000>;
- interrupts = <0 73 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_DISP1>,
- <&tegra_car TEGRA20_CLK_PLL_P>;
- clock-names = "dc", "parent";
- resets = <&tegra_car 27>;
- reset-names = "dc";
-
- rgb {
- status = "disabled";
- };
- };
-
- dc@54240000 {
- compatible = "nvidia,tegra20-dc";
- reg = <0x54240000 0x00040000>;
- interrupts = <0 74 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_DISP2>,
- <&tegra_car TEGRA20_CLK_PLL_P>;
- clock-names = "dc", "parent";
- resets = <&tegra_car 26>;
- reset-names = "dc";
-
- rgb {
- status = "disabled";
- };
- };
-
- hdmi {
- compatible = "nvidia,tegra20-hdmi";
- reg = <0x54280000 0x00040000>;
- interrupts = <0 75 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_HDMI>,
- <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
- clock-names = "hdmi", "parent";
- resets = <&tegra_car 51>;
- reset-names = "hdmi";
- status = "disabled";
- };
-
- tvo {
- compatible = "nvidia,tegra20-tvo";
- reg = <0x542c0000 0x00040000>;
- interrupts = <0 76 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_TVO>;
- status = "disabled";
- };
-
- dsi {
- compatible = "nvidia,tegra20-dsi";
- reg = <0x54300000 0x00040000>;
- clocks = <&tegra_car TEGRA20_CLK_DSI>,
- <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
- clock-names = "dsi", "parent";
- resets = <&tegra_car 48>;
- reset-names = "dsi";
- status = "disabled";
- };
- };
-
- ...
-};
+++ /dev/null
-STMicroelectronics stih4xx platforms
-
-- sti-vtg: video timing generator
- Required properties:
- - compatible: "st,vtg"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- Optional properties:
- - interrupts : VTG interrupt number to the CPU.
- - st,slave: phandle on a slave vtg
-
-- sti-vtac: video timing advanced inter dye communication Rx and TX
- Required properties:
- - compatible: "st,vtac-main" or "st,vtac-aux"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
-
-- sti-display-subsystem: Master device for DRM sub-components
- This device must be the parent of all the sub-components and is responsible
- of bind them.
- Required properties:
- - compatible: "st,sti-display-subsystem"
- - ranges: to allow probing of subdevices
-
-- sti-compositor: frame compositor engine
- must be a child of sti-display-subsystem
- Required properties:
- - compatible: "st,stih<chip>-compositor"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
- - resets: resets to be used by the device
- See ../reset/reset.txt for details.
- - reset-names: names of the resets listed in resets property in the same
- order.
- - st,vtg: phandle(s) on vtg device (main and aux) nodes.
-
-- sti-tvout: video out hardware block
- must be a child of sti-display-subsystem
- Required properties:
- - compatible: "st,stih<chip>-tvout"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - reg-names: names of the mapped memory regions listed in regs property in
- the same order.
- - resets: resets to be used by the device
- See ../reset/reset.txt for details.
- - reset-names: names of the resets listed in resets property in the same
- order.
-
-- sti-hdmi: hdmi output block
- must be a child of sti-display-subsystem
- Required properties:
- - compatible: "st,stih<chip>-hdmi";
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - reg-names: names of the mapped memory regions listed in regs property in
- the same order.
- - interrupts : HDMI interrupt number to the CPU.
- - interrupt-names: name of the interrupts listed in interrupts property in
- the same order
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
- - ddc: phandle of an I2C controller used for DDC EDID probing
-
-sti-hda:
- Required properties:
- must be a child of sti-display-subsystem
- - compatible: "st,stih<chip>-hda"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - reg-names: names of the mapped memory regions listed in regs property in
- the same order.
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
-
-sti-dvo:
- Required properties:
- must be a child of sti-display-subsystem
- - compatible: "st,stih<chip>-dvo"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - reg-names: names of the mapped memory regions listed in regs property in
- the same order.
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
- - pinctrl-0: pin control handle
- - pinctrl-name: names of the pin control to use
- - sti,panel: phandle of the panel connected to the DVO output
-
-sti-hqvdp:
- must be a child of sti-display-subsystem
- Required properties:
- - compatible: "st,stih<chip>-hqvdp"
- - reg: Physical base address of the IP registers and length of memory mapped region.
- - clocks: from common clock binding: handle hardware IP needed clocks, the
- number of clocks may depend of the SoC type.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: names of the clocks listed in clocks property in the same
- order.
- - resets: resets to be used by the device
- See ../reset/reset.txt for details.
- - reset-names: names of the resets listed in resets property in the same
- order.
- - st,vtg: phandle on vtg main device node.
-
-Example:
-
-/ {
- ...
-
- vtg_main_slave: sti-vtg-main-slave@fe85A800 {
- compatible = "st,vtg";
- reg = <0xfe85A800 0x300>;
- interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>;
- };
-
- vtg_main: sti-vtg-main-master@fd348000 {
- compatible = "st,vtg";
- reg = <0xfd348000 0x400>;
- st,slave = <&vtg_main_slave>;
- };
-
- vtg_aux_slave: sti-vtg-aux-slave@fd348400 {
- compatible = "st,vtg";
- reg = <0xfe858200 0x300>;
- interrupts = <GIC_SPI 176 IRQ_TYPE_NONE>;
- };
-
- vtg_aux: sti-vtg-aux-master@fd348400 {
- compatible = "st,vtg";
- reg = <0xfd348400 0x400>;
- st,slave = <&vtg_aux_slave>;
- };
-
-
- sti-vtac-rx-main@fee82800 {
- compatible = "st,vtac-main";
- reg = <0xfee82800 0x200>;
- clock-names = "vtac";
- clocks = <&clk_m_a2_div0 CLK_M_VTAC_MAIN_PHY>;
- };
-
- sti-vtac-rx-aux@fee82a00 {
- compatible = "st,vtac-aux";
- reg = <0xfee82a00 0x200>;
- clock-names = "vtac";
- clocks = <&clk_m_a2_div0 CLK_M_VTAC_AUX_PHY>;
- };
-
- sti-vtac-tx-main@fd349000 {
- compatible = "st,vtac-main";
- reg = <0xfd349000 0x200>, <0xfd320000 0x10000>;
- clock-names = "vtac";
- clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
- };
-
- sti-vtac-tx-aux@fd349200 {
- compatible = "st,vtac-aux";
- reg = <0xfd349200 0x200>, <0xfd320000 0x10000>;
- clock-names = "vtac";
- clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>;
- };
-
- sti-display-subsystem {
- compatible = "st,sti-display-subsystem";
- ranges;
-
- sti-compositor@fd340000 {
- compatible = "st,stih416-compositor";
- reg = <0xfd340000 0x1000>;
- clock-names = "compo_main", "compo_aux",
- "pix_main", "pix_aux";
- clocks = <&clk_m_a2_div1 CLK_M_COMPO_MAIN>, <&clk_m_a2_div1 CLK_M_COMPO_AUX>,
- <&clockgen_c_vcc CLK_S_PIX_MAIN>, <&clockgen_c_vcc CLK_S_PIX_AUX>;
- reset-names = "compo-main", "compo-aux";
- resets = <&softreset STIH416_COMPO_M_SOFTRESET>, <&softreset STIH416_COMPO_A_SOFTRESET>;
- st,vtg = <&vtg_main>, <&vtg_aux>;
- };
-
- sti-tvout@fe000000 {
- compatible = "st,stih416-tvout";
- reg = <0xfe000000 0x1000>, <0xfe85a000 0x400>, <0xfe830000 0x10000>;
- reg-names = "tvout-reg", "hda-reg", "syscfg";
- reset-names = "tvout";
- resets = <&softreset STIH416_HDTVOUT_SOFTRESET>;
- };
-
- sti-hdmi@fe85c000 {
- compatible = "st,stih416-hdmi";
- reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>;
- reg-names = "hdmi-reg", "syscfg";
- interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>;
- interrupt-names = "irq";
- clock-names = "pix", "tmds", "phy", "audio";
- clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>;
- };
-
- sti-hda@fe85a000 {
- compatible = "st,stih416-hda";
- reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>;
- reg-names = "hda-reg", "video-dacs-ctrl";
- clock-names = "pix", "hddac";
- clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>;
- };
-
- sti-dvo@8d00400 {
- compatible = "st,stih407-dvo";
- reg = <0x8d00400 0x200>;
- reg-names = "dvo-reg";
- clock-names = "dvo_pix", "dvo",
- "main_parent", "aux_parent";
- clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>,
- <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_dvo>;
- sti,panel = <&panel_dvo>;
- };
-
- sti-hqvdp@9c000000 {
- compatible = "st,stih407-hqvdp";
- reg = <0x9C00000 0x100000>;
- clock-names = "hqvdp", "pix_main";
- clocks = <&clk_s_c0_flexgen CLK_MAIN_DISP>, <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>;
- reset-names = "hqvdp";
- resets = <&softreset STIH407_HDQVDP_SOFTRESET>;
- st,vtg = <&vtg_main>;
- };
- };
- ...
-};
The HLCDC IP exposes two subdevices:
- a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt
- - a Display Controller: see ../drm/atmel-hlcdc-dc.txt
+ - a Display Controller: see ../display/atmel-hlcdc-dc.txt
Example:
+++ /dev/null
-MIPI DSI (Display Serial Interface) busses
-==========================================
-
-The MIPI Display Serial Interface specifies a serial bus and a protocol for
-communication between a host and up to four peripherals. This document will
-define the syntax used to represent a DSI bus in a device tree.
-
-This document describes DSI bus-specific properties only or defines existing
-standard properties in the context of the DSI bus.
-
-Each DSI host provides a DSI bus. The DSI host controller's node contains a
-set of properties that characterize the bus. Child nodes describe individual
-peripherals on that bus.
-
-The following assumes that only a single peripheral is connected to a DSI
-host. Experience shows that this is true for the large majority of setups.
-
-DSI host
---------
-
-In addition to the standard properties and those defined by the parent bus of
-a DSI host, the following properties apply to a node representing a DSI host.
-
-Required properties:
-- #address-cells: The number of cells required to represent an address on the
- bus. DSI peripherals are addressed using a 2-bit virtual channel number, so
- a maximum of 4 devices can be addressed on a single bus. Hence the value of
- this property should be 1.
-- #size-cells: Should be 0. There are cases where it makes sense to use a
- different value here. See below.
-
-DSI peripheral
---------------
-
-Peripherals are represented as child nodes of the DSI host's node. Properties
-described here apply to all DSI peripherals, but individual bindings may want
-to define additional, device-specific properties.
-
-Required properties:
-- reg: The virtual channel number of a DSI peripheral. Must be in the range
- from 0 to 3.
-
-Some DSI peripherals respond to more than a single virtual channel. In that
-case two alternative representations can be chosen:
-- The reg property can take multiple entries, one for each virtual channel
- that the peripheral responds to.
-- If the virtual channels that a peripheral responds to are consecutive, the
- #size-cells can be set to 1. The first cell of each entry in the reg
- property is the number of the first virtual channel and the second cell is
- the number of consecutive virtual channels.
-
-Example
--------
-
- dsi-host {
- ...
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* peripheral responds to virtual channel 0 */
- peripheral@0 {
- compatible = "...";
- reg = <0>;
- };
-
- ...
- };
-
- dsi-host {
- ...
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* peripheral responds to virtual channels 0 and 2 */
- peripheral@0 {
- compatible = "...";
- reg = <0, 2>;
- };
-
- ...
- };
-
- dsi-host {
- ...
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- /* peripheral responds to virtual channels 1, 2 and 3 */
- peripheral@1 {
- compatible = "...";
- reg = <1 3>;
- };
-
- ...
- };
+++ /dev/null
-NVIDIA Tegra MIPI pad calibration controller
-
-Required properties:
-- compatible: "nvidia,tegra<chip>-mipi"
-- reg: Physical base address and length of the controller's registers.
-- clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
- - mipi-cal
-- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads
- that need to be calibrated for a given device.
-
-User nodes need to contain an nvidia,mipi-calibrate property that has a
-phandle to refer to the calibration controller node and a bitmask of the pads
-that need to be calibrated.
-
-Example:
-
- mipi: mipi@700e3000 {
- compatible = "nvidia,tegra114-mipi";
- reg = <0x700e3000 0x100>;
- clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
- clock-names = "mipi-cal";
- #nvidia,mipi-calibrate-cells = <1>;
- };
-
- ...
-
- host1x@50000000 {
- ...
-
- dsi@54300000 {
- ...
-
- nvidia,mipi-calibrate = <&mipi 0x060>;
-
- ...
- };
-
- ...
- };
+++ /dev/null
-Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "ampire,am800480r3tmqwa1h"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 8.0" WUXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "auo,b101ean01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 10.1" WSVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "auo,b101aw03"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 10.1" WSVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "auo,b101ean01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 10.1" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "auo,b101xtn01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 11.6" HD (1366x768) color TFT-LCD panel
-
-Required properties:
-- compatible: should be "auo,b116xw03"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 13.3" FHD (1920x1080) color TFT-LCD panel
-
-Required properties:
-- compatible: should be "auo,b133htn01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-AU Optronics Corporation 13.3" WXGA (1366x768) TFT LCD panel
-
-Required properties:
-- compatible: should be "auo,b133xtn01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Shanghai AVIC Optoelectronics 7" 1024x600 color TFT-LCD panel
-
-Required properties:
-- compatible: should be "avic,tm070ddh03"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "chunghwa,claa101wa01a"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "chunghwa,claa101wb03"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
-
-Required properties:
-- compatible: should be "edt,et057090dhu"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Emerging Display Technology Corp. ET070080DH6 7.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "edt,et070080dh6"
-
-This panel is the same as ETM0700G0DH6 except for the touchscreen.
-ET070080DH6 is the model with resistive touch.
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Emerging Display Technology Corp. ETM0700G0DH6 7.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "edt,etm0700g0dh6"
-
-This panel is the same as ET070080DH6 except for the touchscreen.
-ETM0700G0DH6 is the model with capacitive multitouch.
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Foxlink Group 5" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "foxlink,fl500wvr00-a0t"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-GiantPlus GPG48273QS5 4.3" (480x272) WQVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "giantplus,gpg48273qs5"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-HannStar Display Corp. HSD070PWW1 7.0" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "hannstar,hsd070pww1"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-HannStar Display Corp. HSD100PXN1 10.1" XGA LVDS panel
-
-Required properties:
-- compatible: should be "hannstar,hsd100pxn1"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Hitachi Ltd. Corporation 9" WVGA (800x480) TFT LCD panel
-
-Required properties:
-- compatible: should be "hit,tx23d38vm0caa"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Innolux AT043TN24 4.3" WQVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "innolux,at043tn24"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-
-Required properties:
-- compatible: should be "innolux,g121i1-l01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel
-
-Required properties:
-- compatible: should be "innolux,n116bge"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-InnoLux 15.6" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "innolux,n156bge-l21"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Innolux Corporation 7.0" WSVGA (1024x600) TFT LCD panel
-
-Required properties:
-- compatible: should be "innolux,zj070na-01p"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-LG 7" (800x480 pixels) TFT LCD panel
-
-Required properties:
-- compatible: should be "lg,lb070wv8"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-LG Corporation 7" WXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "lg,ld070wx3-sl01"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-LG LG4573 TFT Liquid Crystal Display with SPI control bus
-
-Required properties:
- - compatible: "lg,lg4573"
- - reg: address of the panel on the SPI bus
-
-The panel must obey rules for SPI slave device specified in document [1].
-
-[1]: Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Example:
-
- lcd_panel: display@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "lg,lg4573";
- spi-max-frequency = <10000000>;
- reg = <0>;
- };
+++ /dev/null
-LG Corporation 5" HD TFT LCD panel
-
-Required properties:
-- compatible: should be "lg,lh500wx1-sd03"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-LG 12.9" (2560x1700 pixels) TFT LCD panel
-
-Required properties:
-- compatible: should be "lg,lp129qe"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-NEC LCD Technologies,Ltd. WQVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "nec,nl4827hc19-05b"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-OKAYA Electric America, Inc. RS800480T-7X0GP 7" WVGA LCD panel
-
-Required properties:
-- compatible: should be "okaya,rs800480t-7x0gp"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-OrtusTech COM43H4M85ULC Blanview 3.7" TFT-LCD panel
-
-Required properties:
-- compatible: should be "ortustech,com43h4m85ulc"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Panasonic Corporation 10.1" WUXGA TFT LCD panel
-
-Required properties:
-- compatible: should be "panasonic,vvx10f004b00"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus
-
-Required properties:
- - compatible: "samsung,ld9040"
- - reg: address of the panel on SPI bus
- - vdd3-supply: core voltage supply
- - vci-supply: voltage supply for analog circuits
- - reset-gpios: a GPIO spec for the reset pin
- - display-timings: timings for the connected panel according to [1]
-
-The panel must obey rules for SPI slave device specified in document [2].
-
-Optional properties:
- - power-on-delay: delay after turning regulators on [ms]
- - reset-delay: delay after reset sequence [ms]
- - panel-width-mm: physical panel width [mm]
- - panel-height-mm: physical panel height [mm]
-
-The device node can contain one 'port' child node with one child
-'endpoint' node, according to the bindings defined in [3]. This
-node should describe panel's video bus.
-
-[1]: Documentation/devicetree/bindings/video/display-timing.txt
-[2]: Documentation/devicetree/bindings/spi/spi-bus.txt
-[3]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
- lcd@0 {
- compatible = "samsung,ld9040";
- reg = <0>;
- vdd3-supply = <&ldo7_reg>;
- vci-supply = <&ldo17_reg>;
- reset-gpios = <&gpy4 5 0>;
- spi-max-frequency = <1200000>;
- spi-cpol;
- spi-cpha;
- power-on-delay = <10>;
- reset-delay = <10>;
- panel-width-mm = <90>;
- panel-height-mm = <154>;
-
- display-timings {
- timing {
- clock-frequency = <23492370>;
- hactive = <480>;
- vactive = <800>;
- hback-porch = <16>;
- hfront-porch = <16>;
- vback-porch = <2>;
- vfront-porch = <28>;
- hsync-len = <2>;
- vsync-len = <1>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <0>;
- pixelclk-active = <0>;
- };
- };
-
- port {
- lcd_ep: endpoint {
- remote-endpoint = <&fimd_dpi_ep>;
- };
- };
- };
+++ /dev/null
-Samsung Electronics 10.1" WSVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "samsung,ltn101nt05"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Samsung Electronics 14" WXGA (1366x768) TFT LCD panel
-
-Required properties:
-- compatible: should be "samsung,ltn140at29-301"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Samsung S6E8AA0 AMOLED LCD 5.3 inch panel
-
-Required properties:
- - compatible: "samsung,s6e8aa0"
- - reg: the virtual channel number of a DSI peripheral
- - vdd3-supply: core voltage supply
- - vci-supply: voltage supply for analog circuits
- - reset-gpios: a GPIO spec for the reset pin
- - display-timings: timings for the connected panel as described by [1]
-
-Optional properties:
- - power-on-delay: delay after turning regulators on [ms]
- - reset-delay: delay after reset sequence [ms]
- - init-delay: delay after initialization sequence [ms]
- - panel-width-mm: physical panel width [mm]
- - panel-height-mm: physical panel height [mm]
- - flip-horizontal: boolean to flip image horizontally
- - flip-vertical: boolean to flip image vertically
-
-The device node can contain one 'port' child node with one child
-'endpoint' node, according to the bindings defined in [2]. This
-node should describe panel's video bus.
-
-[1]: Documentation/devicetree/bindings/video/display-timing.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
- panel {
- compatible = "samsung,s6e8aa0";
- reg = <0>;
- vdd3-supply = <&vcclcd_reg>;
- vci-supply = <&vlcd_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
- flip-horizontal;
- flip-vertical;
-
- display-timings {
- timing0: timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
- };
+++ /dev/null
-Sharp Microelectronics 10.1" WQXGA TFT LCD panel
-
-This panel requires a dual-channel DSI host to operate. It supports two modes:
-- left-right: each channel drives the left or right half of the screen
-- even-odd: each channel drives the even or odd lines of the screen
-
-Each of the DSI channels controls a separate DSI peripheral. The peripheral
-driven by the first link (DSI-LINK1), left or even, is considered the primary
-peripheral and controls the device. The 'link2' property contains a phandle
-to the peripheral driven by the second link (DSI-LINK2, right or odd).
-
-Note that in video mode the DSI-LINK1 interface always provides the left/even
-pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it
-is possible to program either link to drive the left/even or right/odd pixels
-but for the sake of consistency this binding assumes that the same assignment
-is chosen as for video mode.
-
-Required properties:
-- compatible: should be "sharp,lq101r1sx01"
-- reg: DSI virtual channel of the peripheral
-
-Required properties (for DSI-LINK1 only):
-- link2: phandle to the DSI peripheral on the secondary link. Note that the
- presence of this property marks the containing node as DSI-LINK1.
-- power-supply: phandle of the regulator that provides the supply voltage
-
-Optional properties (for DSI-LINK1 only):
-- backlight: phandle of the backlight device attached to the panel
-
-Example:
-
- dsi@54300000 {
- panel: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
-
- link2 = <&secondary>;
-
- power-supply = <...>;
- backlight = <...>;
- };
- };
-
- dsi@54400000 {
- secondary: panel@0 {
- compatible = "sharp,lq101r1sx01";
- reg = <0>;
- };
- };
+++ /dev/null
-Shelly SCA07010-BFN-LNN 7.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "shelly,sca07010-bfn-lnn"
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
+++ /dev/null
-Simple display panel
-
-Required properties:
-- power-supply: regulator to provide the supply voltage
-
-Optional properties:
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-
-Example:
-
- panel: panel {
- compatible = "cptt,claa101wb01";
- ddc-i2c-bus = <&panelddc>;
-
- power-supply = <&vdd_pnl_reg>;
- enable-gpios = <&gpio 90 0>;
-
- backlight = <&backlight>;
- };
+++ /dev/null
-Analog Device ADV7123 Video DAC
--------------------------------
-
-The ADV7123 is a digital-to-analog converter that outputs VGA signals from a
-parallel video input.
-
-Required properties:
-
-- compatible: Should be "adi,adv7123"
-
-Optional properties:
-
-- psave-gpios: Power save control GPIO
-
-Required nodes:
-
-The ADV7123 has two video ports. Their connections are modeled using the OF
-graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for DPI input
-- Video port 1 for VGA output
-
-
-Example
--------
-
- adv7123: encoder@0 {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- adv7123_in: endpoint@0 {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- adv7123_out: endpoint@0 {
- remote-endpoint = <&vga_connector_in>;
- };
- };
- };
- };
+++ /dev/null
-Analog Device ADV7511(W)/13 HDMI Encoders
------------------------------------------
-
-The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters
-compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
-S/PDIF, CEC and HDCP.
-
-Required properties:
-
-- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513"
-- reg: I2C slave address
-
-The ADV7511 supports a large number of input data formats that differ by their
-color depth, color format, clock mode, bit justification and random
-arrangement of components on the data bus. The combination of the following
-properties describe the input and map directly to the video input tables of the
-ADV7511 datasheet that document all the supported combinations.
-
-- adi,input-depth: Number of bits per color component at the input (8, 10 or
- 12).
-- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
- "yuv444".
-- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
- pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
- data driven on both edges).
-
-The following input format properties are required except in "rgb 1x" and
-"yuv444 1x" modes, in which case they must not be specified.
-
-- adi,input-style: The input components arrangement variant (1, 2 or 3), as
- listed in the input format tables in the datasheet.
-- adi,input-justification: The input bit justification ("left", "evenly",
- "right").
-
-Optional properties:
-
-- interrupts: Specifier for the ADV7511 interrupt
-- pd-gpios: Specifier for the GPIO connected to the power down signal
-
-- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
- (-1200 ps .. 1600 ps). Defaults to no delay.
-- adi,embedded-sync: The input uses synchronization signals embedded in the
- data stream (similar to BT.656). Defaults to separate H/V synchronization
- signals.
-
-Required nodes:
-
-The ADV7511 has two video ports. Their connections are modelled using the OF
-graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for the RGB or YUV input
-- Video port 1 for the HDMI output
-
-
-Example
--------
-
- adv7511w: hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511w_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
+++ /dev/null
-Analog TV Connector
-===================
-
-Required properties:
-- compatible: "composite-video-connector" or "svideo-connector"
-
-Optional properties:
-- label: a symbolic name for the connector
-
-Required nodes:
-- Video port for TV input
-
-Example
--------
-
-tv: connector {
- compatible = "composite-video-connector";
- label = "tv";
-
- port {
- tv_connector_in: endpoint {
- remote-endpoint = <&venc_out>;
- };
- };
-};
+++ /dev/null
-* ARM PrimeCell Color LCD Controller PL110/PL111
-
-See also Documentation/devicetree/bindings/arm/primecell.txt
-
-Required properties:
-
-- compatible: must be one of:
- "arm,pl110", "arm,primecell"
- "arm,pl111", "arm,primecell"
-
-- reg: base address and size of the control registers block
-
-- interrupt-names: either the single entry "combined" representing a
- combined interrupt output (CLCDINTR), or the four entries
- "mbe", "vcomp", "lnbu", "fuf" representing the individual
- CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
-
-- interrupts: contains an interrupt specifier for each entry in
- interrupt-names
-
-- clock-names: should contain "clcdclk" and "apb_pclk"
-
-- clocks: contains phandle and clock specifier pairs for the entries
- in the clock-names property. See
- Documentation/devicetree/binding/clock/clock-bindings.txt
-
-Optional properties:
-
-- memory-region: phandle to a node describing memory (see
- Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
- to be used for the framebuffer; if not present, the framebuffer
- may be located anywhere in the memory
-
-- max-memory-bandwidth: maximum bandwidth in bytes per second that the
- cell's memory interface can handle; if not present, the memory
- interface is fast enough to handle all possible video modes
-
-Required sub-nodes:
-
-- port: describes LCD panel signals, following the common binding
- for video transmitter interfaces; see
- Documentation/devicetree/bindings/media/video-interfaces.txt;
- when it is a TFT panel, the port's endpoint must define the
- following property:
-
- - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
- defining the way CLD pads are wired up; first value
- contains index of the "CLD" external pin (pad) used
- as R0 (first bit of the red component), second value
- index of the pad used as G0, third value index of the
- pad used as B0, see also "LCD panel signal multiplexing
- details" paragraphs in the PL110/PL111 Technical
- Reference Manuals; this implicitly defines available
- color modes, for example:
- - PL111 TFT 4:4:4 panel:
- arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
- - PL110 TFT (1:)5:5:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
- - PL111 TFT (1:)5:5:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
- - PL111 TFT 5:6:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
- - PL110 and PL111 TFT 8:8:8 panel:
- arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
- - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
- arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
-
-
-Example:
-
- clcd@10020000 {
- compatible = "arm,pl111", "arm,primecell";
- reg = <0x10020000 0x1000>;
- interrupt-names = "combined";
- interrupts = <0 44 4>;
- clocks = <&oscclk1>, <&oscclk2>;
- clock-names = "clcdclk", "apb_pclk";
- max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
-
- port {
- clcd_pads: endpoint {
- remote-endpoint = <&clcd_panel>;
- arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
- };
- };
-
- };
-
- panel {
- compatible = "panel-dpi";
-
- port {
- clcd_panel: endpoint {
- remote-endpoint = <&clcd_pads>;
- };
- };
-
- panel-timing {
- clock-frequency = <25175000>;
- hactive = <640>;
- hback-porch = <40>;
- hfront-porch = <24>;
- hsync-len = <96>;
- vactive = <480>;
- vback-porch = <32>;
- vfront-porch = <11>;
- vsync-len = <2>;
- };
- };
+++ /dev/null
-Atmel LCDC Framebuffer
------------------------------------------------------
-
-Required properties:
-- compatible :
- "atmel,at91sam9261-lcdc" ,
- "atmel,at91sam9263-lcdc" ,
- "atmel,at91sam9g10-lcdc" ,
- "atmel,at91sam9g45-lcdc" ,
- "atmel,at91sam9g45es-lcdc" ,
- "atmel,at91sam9rl-lcdc" ,
- "atmel,at32ap-lcdc"
-- reg : Should contain 1 register ranges(address and length).
- Can contain an additional register range(address and length)
- for fixed framebuffer memory. Useful for dedicated memories.
-- interrupts : framebuffer controller interrupt
-- display: a phandle pointing to the display node
-
-Required nodes:
-- display: a display node is required to initialize the lcd panel
- This should be in the board dts.
-- default-mode: a videomode within the display with timing parameters
- as specified below.
-
-Optional properties:
-- lcd-supply: Regulator for LCD supply voltage.
-
-Example:
-
- fb0: fb@0x00500000 {
- compatible = "atmel,at91sam9g45-lcdc";
- reg = <0x00500000 0x1000>;
- interrupts = <23 3 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fb>;
- display = <&display0>;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <1>;
-
- };
-
-Example for fixed framebuffer memory:
-
- fb0: fb@0x00500000 {
- compatible = "atmel,at91sam9263-lcdc";
- reg = <0x00700000 0x1000 0x70000000 0x200000>;
- [...]
- };
-
-Atmel LCDC Display
------------------------------------------------------
-Required properties (as per of_videomode_helper):
-
- - atmel,dmacon: dma controller configuration
- - atmel,lcdcon2: lcd controller configuration
- - atmel,guard-time: lcd guard time (Delay in frame periods)
- - bits-per-pixel: lcd panel bit-depth.
-
-Optional properties (as per of_videomode_helper):
- - atmel,lcdcon-backlight: enable backlight
- - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity
- - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
- - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
-
-Example:
- display0: display {
- bits-per-pixel = <32>;
- atmel,lcdcon-backlight;
- atmel,dmacon = <0x1>;
- atmel,lcdcon2 = <0x80008002>;
- atmel,guard-time = <9>;
- atmel,lcd-wiring-mode = <1>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <9000000>;
- hactive = <480>;
- vactive = <272>;
- hback-porch = <1>;
- hfront-porch = <1>;
- vback-porch = <40>;
- vfront-porch = <1>;
- hsync-len = <45>;
- vsync-len = <1>;
- };
- };
- };
+++ /dev/null
-ps8622-bridge bindings
-
-Required properties:
- - compatible: "parade,ps8622" or "parade,ps8625"
- - reg: first i2c address of the bridge
- - sleep-gpios: OF device-tree gpio specification for PD_ pin.
- - reset-gpios: OF device-tree gpio specification for RST_ pin.
-
-Optional properties:
- - lane-count: number of DP lanes to use
- - use-external-pwm: backlight will be controlled by an external PWM
- - video interfaces: Device node can contain video interface port
- nodes for panel according to [1].
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
- lvds-bridge@48 {
- compatible = "parade,ps8622";
- reg = <0x48>;
- sleep-gpios = <&gpc3 6 1 0 0>;
- reset-gpios = <&gpc3 1 1 0 0>;
- lane-count = <1>;
- ports {
- port@0 {
- bridge_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
- };
+++ /dev/null
-ptn3460 bridge bindings
-
-Required properties:
- - compatible: "nxp,ptn3460"
- - reg: i2c address of the bridge
- - powerdown-gpio: OF device-tree gpio specification for PD_N pin.
- - reset-gpio: OF device-tree gpio specification for RST_N pin.
- - edid-emulation: The EDID emulation entry to use
- +-------+------------+------------------+
- | Value | Resolution | Description |
- | 0 | 1024x768 | NXP Generic |
- | 1 | 1920x1080 | NXP Generic |
- | 2 | 1920x1080 | NXP Generic |
- | 3 | 1600x900 | Samsung LTM200KT |
- | 4 | 1920x1080 | Samsung LTM230HT |
- | 5 | 1366x768 | NXP Generic |
- | 6 | 1600x900 | ChiMei M215HGE |
- +-------+------------+------------------+
-
- - video interfaces: Device node can contain video interface port
- nodes for panel according to [1].
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
- lvds-bridge@20 {
- compatible = "nxp,ptn3460";
- reg = <0x20>;
- powerdown-gpio = <&gpy2 5 1 0 0>;
- reset-gpio = <&gpx1 5 1 0 0>;
- edid-emulation = <5>;
- ports {
- port@0 {
- bridge_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
- };
+++ /dev/null
-* Currus Logic CLPS711X Framebuffer
-
-Required properties:
-- compatible: Shall contain "cirrus,clps711x-fb".
-- reg : Physical base address and length of the controller's registers +
- location and size of the framebuffer memory.
-- clocks : phandle + clock specifier pair of the FB reference clock.
-- display : phandle to a display node as described in
- Documentation/devicetree/bindings/video/display-timing.txt.
- Additionally, the display node has to define properties:
- - bits-per-pixel: Bits per pixel.
- - ac-prescale : LCD AC bias frequency. This frequency is the required
- AC bias frequency for a given manufacturer's LCD plate.
- - cmap-invert : Invert the color levels (Optional).
-
-Optional properties:
-- lcd-supply: Regulator for LCD supply voltage.
-
-Example:
- fb: fb@800002c0 {
- compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb";
- reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
- clocks = <&clks 2>;
- lcd-supply = <®5v0>;
- display = <&display>;
- };
-
- display: display {
- model = "320x240x4";
- native-mode = <&timing0>;
- bits-per-pixel = <4>;
- ac-prescale = <17>;
-
- display-timings {
- timing0: 320x240 {
- hactive = <320>;
- hback-porch = <0>;
- hfront-porch = <0>;
- hsync-len = <0>;
- vactive = <240>;
- vback-porch = <0>;
- vfront-porch = <0>;
- vsync-len = <0>;
- clock-frequency = <6500000>;
- };
- };
- };
+++ /dev/null
-display-timing bindings
-=======================
-
-display-timings node
---------------------
-
-required properties:
- - none
-
-optional properties:
- - native-mode: The native mode for the display, in case multiple modes are
- provided. When omitted, assume the first node is the native.
-
-timing subnode
---------------
-
-required properties:
- - hactive, vactive: display resolution
- - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters
- in pixels
- vfront-porch, vback-porch, vsync-len: vertical display timing parameters in
- lines
- - clock-frequency: display clock in Hz
-
-optional properties:
- - hsync-active: hsync pulse is active low/high/ignored
- - vsync-active: vsync pulse is active low/high/ignored
- - de-active: data-enable pulse is active low/high/ignored
- - pixelclk-active: with
- - active high = drive pixel data on rising edge/
- sample data on falling edge
- - active low = drive pixel data on falling edge/
- sample data on rising edge
- - ignored = ignored
- - interlaced (bool): boolean to enable interlaced mode
- - doublescan (bool): boolean to enable doublescan mode
- - doubleclk (bool): boolean to enable doubleclock mode
-
-All the optional properties that are not bool follow the following logic:
- <1>: high active
- <0>: low active
- omitted: not used on hardware
-
-There are different ways of describing the capabilities of a display. The
-devicetree representation corresponds to the one commonly found in datasheets
-for displays. If a display supports multiple signal timings, the native-mode
-can be specified.
-
-The parameters are defined as:
-
- +----------+-------------------------------------+----------+-------+
- | | ↑ | | |
- | | |vback_porch | | |
- | | ↓ | | |
- +----------#######################################----------+-------+
- | # ↑ # | |
- | # | # | |
- | hback # | # hfront | hsync |
- | porch # | hactive # porch | len |
- |<-------->#<-------+--------------------------->#<-------->|<----->|
- | # | # | |
- | # |vactive # | |
- | # | # | |
- | # ↓ # | |
- +----------#######################################----------+-------+
- | | ↑ | | |
- | | |vfront_porch | | |
- | | ↓ | | |
- +----------+-------------------------------------+----------+-------+
- | | ↑ | | |
- | | |vsync_len | | |
- | | ↓ | | |
- +----------+-------------------------------------+----------+-------+
-
-Example:
-
- display-timings {
- native-mode = <&timing0>;
- timing0: 1080p24 {
- /* 1920x1080p24 */
- clock-frequency = <52000000>;
- hactive = <1920>;
- vactive = <1080>;
- hfront-porch = <25>;
- hback-porch = <25>;
- hsync-len = <25>;
- vback-porch = <2>;
- vfront-porch = <2>;
- vsync-len = <2>;
- hsync-active = <1>;
- };
- };
-
-Every required property also supports the use of ranges, so the commonly used
-datasheet description with minimum, typical and maximum values can be used.
-
-Example:
-
- timing1: timing {
- /* 1920x1080p24 */
- clock-frequency = <148500000>;
- hactive = <1920>;
- vactive = <1080>;
- hsync-len = <0 44 60>;
- hfront-porch = <80 88 95>;
- hback-porch = <100 148 160>;
- vfront-porch = <0 4 6>;
- vback-porch = <0 36 50>;
- vsync-len = <0 5 6>;
- };
+++ /dev/null
-DVI Connector
-==============
-
-Required properties:
-- compatible: "dvi-connector"
-
-Optional properties:
-- label: a symbolic name for the connector
-- ddc-i2c-bus: phandle to the i2c bus that is connected to DVI DDC
-- analog: the connector has DVI analog pins
-- digital: the connector has DVI digital pins
-- dual-link: the connector has pins for DVI dual-link
-
-Required nodes:
-- Video port for DVI input
-
-Note: One (or both) of 'analog' or 'digital' must be set.
-
-Example
--------
-
-dvi0: connector@0 {
- compatible = "dvi-connector";
- label = "dvi";
-
- digital;
-
- ddc-i2c-bus = <&i2c3>;
-
- port {
- dvi_connector_in: endpoint {
- remote-endpoint = <&tfp410_out>;
- };
- };
-};
+++ /dev/null
-Rockchip specific extensions to the Synopsys Designware HDMI
-================================
-
-Required properties:
-- compatible: "rockchip,rk3288-dw-hdmi";
-- reg: Physical base address and length of the controller's registers.
-- clocks: phandle to hdmi iahb and isfr clocks.
-- clock-names: should be "iahb" "isfr"
-- rockchip,grf: this soc should set GRF regs to mux vopl/vopb.
-- interrupts: HDMI interrupt number
-- ports: contain a port node with endpoint definitions as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt. For
- vopb,set the reg = <0> and set the reg = <1> for vopl.
-- reg-io-width: the width of the reg:1,4, the value should be 4 on
- rk3288 platform
-
-Optional properties
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
-
-Example:
-hdmi: hdmi@ff980000 {
- compatible = "rockchip,rk3288-dw-hdmi";
- reg = <0xff980000 0x20000>;
- reg-io-width = <4>;
- ddc-i2c-bus = <&i2c5>;
- rockchip,grf = <&grf>;
- interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
- clock-names = "iahb", "isfr";
- status = "disabled";
- ports {
- hdmi_in: port {
- #address-cells = <1>;
- #size-cells = <0>;
- hdmi_in_vopb: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&vopb_out_hdmi>;
- };
- hdmi_in_vopl: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&vopl_out_hdmi>;
- };
- };
- };
-};
+++ /dev/null
-Device-Tree bindings for Samsung Exynos SoC mobile image compressor (MIC)
-
-MIC (mobile image compressor) resides between decon and mipi dsi. Mipi dsi is
-not capable to transfer high resoltuion frame data as decon can send. MIC
-solves this problem by compressing the frame data by 1/2 before it is
-transferred through mipi dsi. The compressed frame data must be uncompressed in
-the panel PCB.
-
-Required properties:
-- compatible: value should be "samsung,exynos5433-mic".
-- reg: physical base address and length of the MIC registers set and system
- register of mic.
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-- clock-names: list of clock names sorted in the same order as the clocks
- property. Must contain "pclk_mic0", "sclk_rgb_vclk_to_mic0".
-- samsung,disp-syscon: the reference node for syscon for DISP block.
-- ports: contains a port which is connected to decon node and dsi node.
- address-cells and size-cells must 1 and 0, respectively.
-- port: contains an endpoint node which is connected to the endpoint in the
- decon node or dsi node. The reg value must be 0 and 1 respectively.
-
-Example:
-SoC specific DT entry:
-mic: mic@13930000 {
- compatible = "samsung,exynos5433-mic";
- reg = <0x13930000 0x48>;
- clocks = <&cmu_disp CLK_PCLK_MIC0>,
- <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
- clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
- samsung,disp-syscon = <&syscon_disp>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- mic_to_decon: endpoint {
- remote-endpoint = <&decon_to_mic>;
- };
- };
-
- port@1 {
- reg = <1>;
- mic_to_dsi: endpoint {
- remote-endpoint = <&dsi_to_mic>;
- };
- };
- };
-};
+++ /dev/null
-Device-Tree bindings for Samsung Exynos SoC display controller (DECON)
-
-DECON (Display and Enhancement Controller) is the Display Controller for the
-Exynos series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be "samsung,exynos5433-decon";
-- reg: physical base address and length of the DECON registers set.
-- interrupts: should contain a list of all DECON IP block interrupts in the
- order: VSYNC, LCD_SYSTEM. The interrupt specifier format
- depends on the interrupt controller used.
-- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys"
- in the same order as they were listed in the interrupts
- property.
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-- clock-names: list of clock names sorted in the same order as the clocks
- property. Must contain "aclk_decon", "aclk_smmu_decon0x",
- "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk",
- "sclk_decon_eclk"
-- ports: contains a port which is connected to mic node. address-cells and
- size-cells must 1 and 0, respectively.
-- port: contains an endpoint node which is connected to the endpoint in the mic
- node. The reg value muset be 0.
-- i80-if-timings: specify whether the panel which is connected to decon uses
- i80 lcd interface or mipi video interface. This node contains
- no timing information as that of fimd does. Because there is
- no register in decon to specify i80 interface timing value,
- it is not needed, but make it remain to use same kind of node
- in fimd and exynos7 decon.
-
-Example:
-SoC specific DT entry:
-decon: decon@13800000 {
- compatible = "samsung,exynos5433-decon";
- reg = <0x13800000 0x2104>;
- clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
- <&cmu_disp CLK_ACLK_XIU_DECON0X>,
- <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
- <&cmu_disp CLK_SCLK_DECON_VCLK>,
- <&cmu_disp CLK_SCLK_DECON_ECLK>;
- clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x",
- "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk";
- interrupt-names = "vsync", "lcd_sys";
- interrupts = <0 202 0>, <0 203 0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- decon_to_mic: endpoint {
- remote-endpoint = <&mic_to_decon>;
- };
- };
- };
-};
-
-Board specific DT entry:
-&decon {
- i80-if-timings {
- };
-};
+++ /dev/null
-Device-Tree bindings for Samsung Exynos7 SoC display controller (DECON)
-
-DECON (Display and Enhancement Controller) is the Display Controller for the
-Exynos7 series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be "samsung,exynos7-decon";
-
-- reg: physical base address and length of the DECON registers set.
-
-- interrupt-parent: should be the phandle of the decon controller's
- parent interrupt controller.
-
-- interrupts: should contain a list of all DECON IP block interrupts in the
- order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
- format depends on the interrupt controller used.
-
-- interrupt-names: should contain the interrupt names: "fifo", "vsync",
- "lcd_sys", in the same order as they were listed in the interrupts
- property.
-
-- pinctrl-0: pin control group to be used for this controller.
-
-- pinctrl-names: must contain a "default" entry.
-
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-
-- clock-names: list of clock names sorted in the same order as the clocks
- property. Must contain "pclk_decon0", "aclk_decon0",
- "decon0_eclk", "decon0_vclk".
-- i80-if-timings: timing configuration for lcd i80 interface support.
-
-Optional Properties:
-- samsung,power-domain: a phandle to DECON power domain node.
-- display-timings: timing settings for DECON, as described in document [1].
- Can be used in case timings cannot be provided otherwise
- or to override timings provided by the panel.
-
-[1]: Documentation/devicetree/bindings/video/display-timing.txt
-
-Example:
-
-SoC specific DT entry:
-
- decon@13930000 {
- compatible = "samsung,exynos7-decon";
- interrupt-parent = <&combiner>;
- reg = <0x13930000 0x1000>;
- interrupt-names = "lcd_sys", "vsync", "fifo";
- interrupts = <0 188 0>, <0 189 0>, <0 190 0>;
- clocks = <&clock_disp PCLK_DECON_INT>,
- <&clock_disp ACLK_DECON_INT>,
- <&clock_disp SCLK_DECON_INT_ECLK>,
- <&clock_disp SCLK_DECON_INT_EXTCLKPLL>;
- clock-names = "pclk_decon0", "aclk_decon0", "decon0_eclk",
- "decon0_vclk";
- status = "disabled";
- };
-
-Board specific DT entry:
-
- decon@13930000 {
- pinctrl-0 = <&lcd_clk &pwm1_out>;
- pinctrl-names = "default";
- status = "okay";
- };
+++ /dev/null
-The Exynos display port interface should be configured based on
-the type of panel connected to it.
-
-We use two nodes:
- -dp-controller node
- -dptx-phy node(defined inside dp-controller node)
-
-For the DP-PHY initialization, we use the dptx-phy node.
-Required properties for dptx-phy: deprecated, use phys and phy-names
- -reg: deprecated
- Base address of DP PHY register.
- -samsung,enable-mask: deprecated
- The bit-mask used to enable/disable DP PHY.
-
-For the Panel initialization, we read data from dp-controller node.
-Required properties for dp-controller:
- -compatible:
- should be "samsung,exynos5-dp".
- -reg:
- physical base address of the controller and length
- of memory mapped region.
- -interrupts:
- interrupt combiner values.
- -clocks:
- from common clock binding: handle to dp clock.
- -clock-names:
- from common clock binding: Shall be "dp".
- -interrupt-parent:
- phandle to Interrupt combiner node.
- -phys:
- from general PHY binding: the phandle for the PHY device.
- -phy-names:
- from general PHY binding: Should be "dp".
- -samsung,color-space:
- input video data format.
- COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
- -samsung,dynamic-range:
- dynamic range for input video data.
- VESA = 0, CEA = 1
- -samsung,ycbcr-coeff:
- YCbCr co-efficients for input video.
- COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
- -samsung,color-depth:
- number of bits per colour component.
- COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
- -samsung,link-rate:
- link rate supported by the panel.
- LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
- -samsung,lane-count:
- number of lanes supported by the panel.
- LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
- - display-timings: timings for the connected panel as described by
- Documentation/devicetree/bindings/video/display-timing.txt
-
-Optional properties for dp-controller:
- -interlaced:
- interlace scan mode.
- Progressive if defined, Interlaced if not defined
- -vsync-active-high:
- VSYNC polarity configuration.
- High if defined, Low if not defined
- -hsync-active-high:
- HSYNC polarity configuration.
- High if defined, Low if not defined
- -samsung,hpd-gpio:
- Hotplug detect GPIO.
- Indicates which GPIO should be used for hotplug
- detection
- -video interfaces: Device node can contain video interface port
- nodes according to [1].
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
-SOC specific portion:
- dp-controller {
- compatible = "samsung,exynos5-dp";
- reg = <0x145b0000 0x10000>;
- interrupts = <10 3>;
- interrupt-parent = <&combiner>;
- clocks = <&clock 342>;
- clock-names = "dp";
-
- phys = <&dp_phy>;
- phy-names = "dp";
- };
-
-Board Specific portion:
- dp-controller {
- samsung,color-space = <0>;
- samsung,dynamic-range = <0>;
- samsung,ycbcr-coeff = <0>;
- samsung,color-depth = <1>;
- samsung,link-rate = <0x0a>;
- samsung,lane-count = <4>;
-
- display-timings {
- native-mode = <&lcd_timing>;
- lcd_timing: 1366x768 {
- clock-frequency = <70589280>;
- hactive = <1366>;
- vactive = <768>;
- hfront-porch = <40>;
- hback-porch = <40>;
- hsync-len = <32>;
- vback-porch = <10>;
- vfront-porch = <12>;
- vsync-len = <6>;
- };
- };
-
- ports {
- port@0 {
- dp_out: endpoint {
- remote-endpoint = <&bridge_in>;
- };
- };
- };
- };
+++ /dev/null
-Exynos MIPI DSI Master
-
-Required properties:
- - compatible: value should be one of the following
- "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */
- "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */
- "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */
- "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */
- "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */
- - reg: physical base address and length of the registers set for the device
- - interrupts: should contain DSI interrupt
- - clocks: list of clock specifiers, must contain an entry for each required
- entry in clock-names
- - clock-names: should include "bus_clk"and "sclk_mipi" entries
- the use of "pll_clk" is deprecated
- - phys: list of phy specifiers, must contain an entry for each required
- entry in phy-names
- - phy-names: should include "dsim" entry
- - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
- - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
- - samsung,pll-clock-frequency: specifies frequency of the oscillator clock
- - #address-cells, #size-cells: should be set respectively to <1> and <0>
- according to DSI host bindings (see MIPI DSI bindings [1])
-
-Optional properties:
- - power-domains: a phandle to DSIM power domain node
-
-Child nodes:
- Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
-
-Video interfaces:
- Device node can contain video interface port nodes according to [2].
- The following are properties specific to those nodes:
-
- port node inbound:
- - reg: (required) must be 0.
- port node outbound:
- - reg: (required) must be 1.
-
- endpoint node connected from mic node (reg = 0):
- - remote-endpoint: specifies the endpoint in mic node. This node is required
- for Exynos5433 mipi dsi. So mic can access to panel node
- thoughout this dsi node.
- endpoint node connected to panel node (reg = 1):
- - remote-endpoint: specifies the endpoint in panel node. This node is
- required in all kinds of exynos mipi dsi to represent
- the connection between mipi dsi and panel.
- - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
- mode
- - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
-
-[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
- dsi@11C80000 {
- compatible = "samsung,exynos4210-mipi-dsi";
- reg = <0x11C80000 0x10000>;
- interrupts = <0 79 0>;
- clocks = <&clock 286>, <&clock 143>;
- clock-names = "bus_clk", "sclk_mipi";
- phys = <&mipi_phy 1>;
- phy-names = "dsim";
- vddcore-supply = <&vusb_reg>;
- vddio-supply = <&vmipi_reg>;
- power-domains = <&pd_lcd0>;
- #address-cells = <1>;
- #size-cells = <0>;
- samsung,pll-clock-frequency = <24000000>;
-
- panel@1 {
- reg = <0>;
- ...
- port {
- panel_ep: endpoint {
- remote-endpoint = <&dsi_ep>;
- };
- };
- };
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- decon_to_mic: endpoint {
- remote-endpoint = <&mic_to_decon>;
- };
- };
-
- port@1 {
- reg = <1>;
- dsi_ep: endpoint {
- reg = <0>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- remote-endpoint = <&panel_ep>;
- };
- };
- };
- };
+++ /dev/null
-Device-Tree bindings for drm hdmi driver
-
-Required properties:
-- compatible: value should be one among the following:
- 1) "samsung,exynos5-hdmi" <DEPRECATED>
- 2) "samsung,exynos4210-hdmi"
- 3) "samsung,exynos4212-hdmi"
- 4) "samsung,exynos5420-hdmi"
-- reg: physical base address of the hdmi and length of memory mapped
- region.
-- interrupts: interrupt number to the cpu.
-- hpd-gpio: following information about the hotplug gpio pin.
- a) phandle of the gpio controller node.
- b) pin number within the gpio controller.
- c) optional flags and pull up/down.
-- clocks: list of clock IDs from SoC clock driver.
- a) hdmi: Gate of HDMI IP bus clock.
- b) sclk_hdmi: Gate of HDMI special clock.
- c) sclk_pixel: Pixel special clock, one of the two possible inputs of
- HDMI clock mux.
- d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of
- HDMI clock mux.
- e) mout_hdmi: It is required by the driver to switch between the 2
- parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable
- after configuration, parent is set to sclk_hdmiphy else
- sclk_pixel.
-- clock-names: aliases as per driver requirements for above clock IDs:
- "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi".
-- ddc: phandle to the hdmi ddc node
-- phy: phandle to the hdmi phy node
-- samsung,syscon-phandle: phandle for system controller node for PMU.
-
-Example:
-
- hdmi {
- compatible = "samsung,exynos4212-hdmi";
- reg = <0x14530000 0x100000>;
- interrupts = <0 95 0>;
- hpd-gpio = <&gpx3 7 1>;
- ddc = <&hdmi_ddc_node>;
- phy = <&hdmi_phy_node>;
- samsung,syscon-phandle = <&pmu_system_controller>;
- };
+++ /dev/null
-Device-Tree bindings for hdmiddc driver
-
-Required properties:
-- compatible: value should be one of the following
- 1) "samsung,exynos5-hdmiddc" <DEPRECATED>
- 2) "samsung,exynos4210-hdmiddc"
-
-- reg: I2C address of the hdmiddc device.
-
-Example:
-
- hdmiddc {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
- };
+++ /dev/null
-Device-Tree bindings for hdmiphy driver
-
-Required properties:
-- compatible: value should be one of the following:
- 1) "samsung,exynos5-hdmiphy" <DEPRECATED>
- 2) "samsung,exynos4210-hdmiphy".
- 3) "samsung,exynos4212-hdmiphy".
-- reg: I2C address of the hdmiphy device.
-
-Example:
-
- hdmiphy {
- compatible = "samsung,exynos4210-hdmiphy";
- reg = <0x38>;
- };
+++ /dev/null
-Device-Tree bindings for mixer driver
-
-Required properties:
-- compatible: value should be one of the following:
- 1) "samsung,exynos5-mixer" <DEPRECATED>
- 2) "samsung,exynos4210-mixer"
- 3) "samsung,exynos4212-mixer"
- 4) "samsung,exynos5250-mixer"
- 5) "samsung,exynos5420-mixer"
-
-- reg: physical base address of the mixer and length of memory mapped
- region.
-- interrupts: interrupt number to the cpu.
-- clocks: list of clock IDs from SoC clock driver.
- a) mixer: Gate of Mixer IP bus clock.
- b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of
- mixer mux.
- c) hdmi: Gate of HDMI IP bus clock, needed together with sclk_hdmi.
-
-Example:
-
- mixer {
- compatible = "samsung,exynos5250-mixer";
- reg = <0x14450000 0x10000>;
- interrupts = <0 94 0>;
- };
+++ /dev/null
-Device Tree bindings for Freescale DCU DRM Driver
-
-Required properties:
-- compatible: Should be one of
- * "fsl,ls1021a-dcu".
- * "fsl,vf610-dcu".
-
-- reg: Address and length of the register set for dcu.
-- clocks: From common clock binding: handle to dcu clock.
-- clock-names: From common clock binding: Shall be "dcu".
-- big-endian Boolean property, LS1021A DCU registers are big-endian.
-- fsl,panel: The phandle to panel node.
-
-Examples:
-dcu: dcu@2ce0000 {
- compatible = "fsl,ls1021a-dcu";
- reg = <0x0 0x2ce0000 0x0 0x10000>;
- clocks = <&platform_clk 0>;
- clock-names = "dcu";
- big-endian;
- fsl,panel = <&panel>;
-};
+++ /dev/null
-Freescale imx21 Framebuffer
-
-This framebuffer driver supports devices imx1, imx21, imx25, and imx27.
-
-Required properties:
-- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21
-- reg : Should contain 1 register ranges(address and length)
-- interrupts : One interrupt of the fb dev
-
-Required nodes:
-- display: Phandle to a display node as described in
- Documentation/devicetree/bindings/video/display-timing.txt
- Additional, the display node has to define properties:
- - bits-per-pixel: Bits per pixel
- - fsl,pcr: LCDC PCR value
-
-Optional properties:
-- lcd-supply: Regulator for LCD supply voltage.
-- fsl,dmacr: DMA Control Register value. This is optional. By default, the
- register is not modified as recommended by the datasheet.
-- fsl,lpccr: Contrast Control Register value. This property provides the
- default value for the contrast control register.
- If that property is omitted, the register is zeroed.
-- fsl,lscr1: LCDC Sharp Configuration Register value.
-
-Example:
-
- imxfb: fb@10021000 {
- compatible = "fsl,imx21-fb";
- interrupts = <61>;
- reg = <0x10021000 0x1000>;
- display = <&display0>;
- };
-
- ...
-
- display0: display0 {
- model = "Primeview-PD050VL1";
- native-mode = <&timing_disp0>;
- bits-per-pixel = <16>;
- fsl,pcr = <0xf0c88080>; /* non-standard but required */
- display-timings {
- timing_disp0: 640x480 {
- hactive = <640>;
- vactive = <480>;
- hback-porch = <112>;
- hfront-porch = <36>;
- hsync-len = <32>;
- vback-porch = <33>;
- vfront-porch = <33>;
- vsync-len = <2>;
- clock-frequency = <25000000>;
- };
- };
- };
+++ /dev/null
-HDMI Connector
-==============
-
-Required properties:
-- compatible: "hdmi-connector"
-- type: the HDMI connector type: "a", "b", "c", "d" or "e"
-
-Optional properties:
-- label: a symbolic name for the connector
-- hpd-gpios: HPD GPIO number
-
-Required nodes:
-- Video port for HDMI input
-
-Example
--------
-
-hdmi0: connector@1 {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
-};
+++ /dev/null
-LG.Philips LB035Q02 Panel
-=========================
-
-Required properties:
-- compatible: "lgphilips,lb035q02"
-- enable-gpios: panel enable gpio
-
-Optional properties:
-- label: a symbolic name for the panel
-
-Required nodes:
-- Video port for DPI input
-
-Example
--------
-
-lcd-panel: panel@0 {
- compatible = "lgphilips,lb035q02";
- reg = <0>;
- spi-max-frequency = <100000>;
- spi-cpol;
- spi-cpha;
-
- label = "lcd";
-
- enable-gpios = <&gpio7 7 0>;
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-};
+++ /dev/null
-Generic MIPI DPI Panel
-======================
-
-Required properties:
-- compatible: "panel-dpi"
-
-Optional properties:
-- label: a symbolic name for the panel
-- enable-gpios: panel enable gpio
-
-Required nodes:
-- "panel-timing" containing video timings
- (Documentation/devicetree/bindings/video/display-timing.txt)
-- Video port for DPI input
-
-Example
--------
-
-lcd0: display@0 {
- compatible = "samsung,lte430wq-f0c", "panel-dpi";
- label = "lcd";
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- panel-timing {
- clock-frequency = <9200000>;
- hactive = <480>;
- vactive = <272>;
- hfront-porch = <8>;
- hback-porch = <4>;
- hsync-len = <41>;
- vback-porch = <2>;
- vfront-porch = <4>;
- vsync-len = <10>;
-
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
-};
+++ /dev/null
-Generic MIPI DSI Command Mode Panel
-===================================
-
-Required properties:
-- compatible: "panel-dsi-cm"
-
-Optional properties:
-- label: a symbolic name for the panel
-- reset-gpios: panel reset gpio
-- te-gpios: panel TE gpio
-
-Required nodes:
-- Video port for DSI input
-
-Example
--------
-
-lcd0: display {
- compatible = "tpo,taal", "panel-dsi-cm";
- label = "lcd0";
-
- reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
-
- port {
- lcd0_in: endpoint {
- remote-endpoint = <&dsi1_out_ep>;
- };
- };
-};
+++ /dev/null
-* Renesas R-Car Display Unit (DU)
-
-Required Properties:
-
- - compatible: must be one of the following.
- - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU
- - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU
- - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU
-
- - reg: A list of base address and length of each memory resource, one for
- each entry in the reg-names property.
- - reg-names: Name of the memory resources. The DU requires one memory
- resource for the DU core (named "du") and one memory resource for each
- LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical
- index).
-
- - interrupt-parent: phandle of the parent interrupt controller.
- - interrupts: Interrupt specifiers for the DU interrupts.
-
- - clocks: A list of phandles + clock-specifier pairs, one for each entry in
- the clock-names property.
- - clock-names: Name of the clocks. This property is model-dependent.
- - R8A7779 uses a single functional clock. The clock doesn't need to be
- named.
- - R8A7790 and R8A7791 use one functional clock per channel and one clock
- per LVDS encoder. The functional clocks must be named "du.x" with "x"
- being the channel numerical index. The LVDS clocks must be named
- "lvds.x" with "x" being the LVDS encoder numerical index.
- - In addition to the functional and encoder clocks, all DU versions also
- support externally supplied pixel clocks. Those clocks are optional.
- When supplied they must be named "dclkin.x" with "x" being the input
- clock numerical index.
-
-Required nodes:
-
-The connections to the DU output video ports are modeled using the OF graph
-bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-The following table lists for each supported model the port number
-corresponding to each DU output.
-
- Port 0 Port1 Port2
------------------------------------------------------------------------------
- R8A7779 (H1) DPAD 0 DPAD 1 -
- R8A7790 (H2) DPAD LVDS 0 LVDS 1
- R8A7791 (M2) DPAD LVDS 0 -
-
-
-Example: R8A7790 (R-Car H2) DU
-
- du: du@feb00000 {
- compatible = "renesas,du-r8a7790";
- reg = <0 0xfeb00000 0 0x70000>,
- <0 0xfeb90000 0 0x1c>,
- <0 0xfeb94000 0 0x1c>;
- reg-names = "du", "lvds.0", "lvds.1";
- interrupt-parent = <&gic>;
- interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>,
- <0 268 IRQ_TYPE_LEVEL_HIGH>,
- <0 269 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&mstp7_clks R8A7790_CLK_DU0>,
- <&mstp7_clks R8A7790_CLK_DU1>,
- <&mstp7_clks R8A7790_CLK_DU2>,
- <&mstp7_clks R8A7790_CLK_LVDS0>,
- <&mstp7_clks R8A7790_CLK_LVDS1>;
- clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- du_out_rgb: endpoint {
- };
- };
- port@1 {
- reg = <1>;
- du_out_lvds0: endpoint {
- };
- };
- port@2 {
- reg = <2>;
- du_out_lvds1: endpoint {
- };
- };
- };
- };
+++ /dev/null
-Rockchip DRM master device
-================================
-
-The Rockchip DRM master device is a virtual device needed to list all
-vop devices or other display interface nodes that comprise the
-graphics subsystem.
-
-Required properties:
-- compatible: Should be "rockchip,display-subsystem"
-- ports: Should contain a list of phandles pointing to display interface port
- of vop devices. vop definitions as defined in
- Documentation/devicetree/bindings/video/rockchip-vop.txt
-
-example:
-
-display-subsystem {
- compatible = "rockchip,display-subsystem";
- ports = <&vopl_out>, <&vopb_out>;
-};
+++ /dev/null
-device-tree bindings for rockchip soc display controller (vop)
-
-VOP (Visual Output Processor) is the Display Controller for the Rockchip
-series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be one of the following
- "rockchip,rk3288-vop";
-
-- interrupts: should contain a list of all VOP IP block interrupts in the
- order: VSYNC, LCD_SYSTEM. The interrupt specifier
- format depends on the interrupt controller used.
-
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-
-- clock-names: Must contain
- aclk_vop: for ddr buffer transfer.
- hclk_vop: for ahb bus to R/W the phy regs.
- dclk_vop: pixel clock.
-
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names: Must include the following entries:
- - axi
- - ahb
- - dclk
-
-- iommus: required a iommu node
-
-- port: A port node with endpoint definitions as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-SoC specific DT entry:
- vopb: vopb@ff930000 {
- compatible = "rockchip,rk3288-vop";
- reg = <0xff930000 0x19c>;
- interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>;
- clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
- resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>;
- reset-names = "axi", "ahb", "dclk";
- iommus = <&vopb_mmu>;
- vopb_out: port {
- #address-cells = <1>;
- #size-cells = <0>;
- vopb_out_edp: endpoint@0 {
- reg = <0>;
- remote-endpoint=<&edp_in_vopb>;
- };
- vopb_out_hdmi: endpoint@1 {
- reg = <1>;
- remote-endpoint=<&hdmi_in_vopb>;
- };
- };
- };
+++ /dev/null
-Device-Tree bindings for Samsung SoC display controller (FIMD)
-
-FIMD (Fully Interactive Mobile Display) is the Display Controller for the
-Samsung series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be one of the following
- "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
- "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
- "samsung,s5pv210-fimd"; /* for S5PV210 SoC */
- "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
- "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
- "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
- "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
-
-- reg: physical base address and length of the FIMD registers set.
-
-- interrupt-parent: should be the phandle of the fimd controller's
- parent interrupt controller.
-
-- interrupts: should contain a list of all FIMD IP block interrupts in the
- order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
- format depends on the interrupt controller used.
-
-- interrupt-names: should contain the interrupt names: "fifo", "vsync",
- "lcd_sys", in the same order as they were listed in the interrupts
- property.
-
-- pinctrl-0: pin control group to be used for this controller.
-
-- pinctrl-names: must contain a "default" entry.
-
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-
-- clock-names: list of clock names sorted in the same order as the clocks
- property. Must contain "sclk_fimd" and "fimd".
-
-Optional Properties:
-- power-domains: a phandle to FIMD power domain node.
-- samsung,invert-vden: video enable signal is inverted
-- samsung,invert-vclk: video clock signal is inverted
-- display-timings: timing settings for FIMD, as described in document [1].
- Can be used in case timings cannot be provided otherwise
- or to override timings provided by the panel.
-- samsung,sysreg: handle to syscon used to control the system registers
-- i80-if-timings: timing configuration for lcd i80 interface support.
- - cs-setup: clock cycles for the active period of address signal is enabled
- until chip select is enabled.
- If not specified, the default value(0) will be used.
- - wr-setup: clock cycles for the active period of CS signal is enabled until
- write signal is enabled.
- If not specified, the default value(0) will be used.
- - wr-active: clock cycles for the active period of CS is enabled.
- If not specified, the default value(1) will be used.
- - wr-hold: clock cycles for the active period of CS is disabled until write
- signal is disabled.
- If not specified, the default value(0) will be used.
-
- The parameters are defined as:
-
- VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
- : : : : :
- Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
- | cs-setup+1 | : : :
- |<---------->| : : :
- Chip Select ???????????????|____________:____________:____________|??
- | wr-setup+1 | | wr-hold+1 |
- |<---------->| |<---------->|
- Write Enable ????????????????????????????|____________|???????????????
- | wr-active+1|
- |<---------->|
- Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
-
-The device node can contain 'port' child nodes according to the bindings defined
-in [2]. The following are properties specific to those nodes:
-- reg: (required) port index, can be:
- 0 - for CAMIF0 input,
- 1 - for CAMIF1 input,
- 2 - for CAMIF2 input,
- 3 - for parallel output,
- 4 - for write-back interface
-
-[1]: Documentation/devicetree/bindings/video/display-timing.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
-SoC specific DT entry:
-
- fimd@11c00000 {
- compatible = "samsung,exynos4210-fimd";
- interrupt-parent = <&combiner>;
- reg = <0x11c00000 0x20000>;
- interrupt-names = "fifo", "vsync", "lcd_sys";
- interrupts = <11 0>, <11 1>, <11 2>;
- clocks = <&clock 140>, <&clock 283>;
- clock-names = "sclk_fimd", "fimd";
- power-domains = <&pd_lcd0>;
- status = "disabled";
- };
-
-Board specific DT entry:
-
- fimd@11c00000 {
- pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
- pinctrl-names = "default";
- status = "okay";
- };
+++ /dev/null
-SHARP LS037V7DW01 TFT-LCD panel
-===================================
-
-Required properties:
-- compatible: "sharp,ls037v7dw01"
-
-Optional properties:
-- label: a symbolic name for the panel
-- enable-gpios: a GPIO spec for the optional enable pin.
- This pin is the INI pin as specified in the LS037V7DW01.pdf file.
-- reset-gpios: a GPIO spec for the optional reset pin.
- This pin is the RESB pin as specified in the LS037V7DW01.pdf file.
-- mode-gpios: a GPIO
- ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file.
-
-Required nodes:
-- Video port for DPI input
-
-This panel can have zero to five GPIOs to configure to change configuration
-between QVGA and VGA mode and the scan direction. As these pins can be also
-configured with external pulls, all the GPIOs are considered optional with holes
-in the array.
-
-Example
--------
-
-Example when connected to a omap2+ based device:
-
-lcd0: display {
- compatible = "sharp,ls037v7dw01";
- power-supply = <&lcd_3v3>;
- enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
- reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
- mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
- &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
- &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-};
+++ /dev/null
-Sunxi specific Simple Framebuffer bindings
-
-This binding documents sunxi specific extensions to the simple-framebuffer
-bindings. The sunxi simplefb u-boot code relies on the devicetree containing
-pre-populated simplefb nodes.
-
-These extensions are intended so that u-boot can select the right node based
-on which pipeline is being used. As such they are solely intended for
-firmware / bootloader use, and the OS should ignore them.
-
-Required properties:
-- compatible: "allwinner,simple-framebuffer"
-- allwinner,pipeline, one of:
- "de_be0-lcd0"
- "de_be1-lcd1"
- "de_be0-lcd0-hdmi"
- "de_be1-lcd1-hdmi"
-
-Example:
-
-chosen {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- framebuffer@0 {
- compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
- allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>;
- status = "disabled";
- };
-};
+++ /dev/null
-Simple Framebuffer
-
-A simple frame-buffer describes a frame-buffer setup by firmware or
-the bootloader, with the assumption that the display hardware has already
-been set up to scan out from the memory pointed to by the reg property.
-
-Since simplefb nodes represent runtime information they must be sub-nodes of
-the chosen node (*). Simplefb nodes must be named "framebuffer@<address>".
-
-If the devicetree contains nodes for the display hardware used by a simplefb,
-then the simplefb node must contain a property called "display", which
-contains a phandle pointing to the primary display hw node, so that the OS
-knows which simplefb to disable when handing over control to a driver for the
-real hardware. The bindings for the hw nodes must specify which node is
-considered the primary node.
-
-It is advised to add display# aliases to help the OS determine how to number
-things. If display# aliases are used, then if the simplefb node contains a
-"display" property then the /aliases/display# path must point to the display
-hw node the "display" property points to, otherwise it must point directly
-to the simplefb node.
-
-If a simplefb node represents the preferred console for user interaction,
-then the chosen node's stdout-path property should point to it, or to the
-primary display hw node, as with display# aliases. If display aliases are
-used then it should be set to the alias instead.
-
-It is advised that devicetree files contain pre-filled, disabled framebuffer
-nodes, so that the firmware only needs to update the mode information and
-enable them. This way if e.g. later on support for more display clocks get
-added, the simplefb nodes will already contain this info and the firmware
-does not need to be updated.
-
-If pre-filled framebuffer nodes are used, the firmware may need extra
-information to find the right node. In that case an extra platform specific
-compatible and platform specific properties should be used and documented,
-see e.g. simple-framebuffer-sunxi.txt .
-
-Required properties:
-- compatible: "simple-framebuffer"
-- reg: Should contain the location and size of the framebuffer memory.
-- width: The width of the framebuffer in pixels.
-- height: The height of the framebuffer in pixels.
-- stride: The number of bytes in each line of the framebuffer.
-- format: The format of the framebuffer surface. Valid values are:
- - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
- - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r).
-
-Optional properties:
-- clocks : List of clocks used by the framebuffer. Clocks listed here
- are expected to already be configured correctly. The OS must
- ensure these clocks are not modified or disabled while the
- simple framebuffer remains active.
-- display : phandle pointing to the primary display hardware node
-
-Example:
-
-aliases {
- display0 = &lcdc0;
-}
-
-chosen {
- framebuffer0: framebuffer@1d385000 {
- compatible = "simple-framebuffer";
- reg = <0x1d385000 (1600 * 1200 * 2)>;
- width = <1600>;
- height = <1200>;
- stride = <(1600 * 2)>;
- format = "r5g6b5";
- clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>;
- display = <&lcdc0>;
- };
- stdout-path = "display0";
-};
-
-soc@01c00000 {
- lcdc0: lcdc@1c0c000 {
- compatible = "allwinner,sun4i-a10-lcdc";
- ...
- };
-};
-
-
-*) Older devicetree files may have a compatible = "simple-framebuffer" node
-in a different place, operating systems must first enumerate any compatible
-nodes found under chosen and then check for other compatible nodes.
+++ /dev/null
-Sony ACX565AKM SDI Panel
-========================
-
-Required properties:
-- compatible: "sony,acx565akm"
-
-Optional properties:
-- label: a symbolic name for the panel
-- reset-gpios: panel reset gpio
-
-Required nodes:
-- Video port for SDI input
-
-Example
--------
-
-acx565akm@2 {
- compatible = "sony,acx565akm";
- spi-max-frequency = <6000000>;
- reg = <2>;
-
- label = "lcd";
- reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&sdi_out>;
- };
- };
-};
+++ /dev/null
-* Solomon SSD1289 Framebuffer Driver
-
-Required properties:
- - compatible: Should be "solomon,ssd1289fb". The only supported bus for
- now is lbc.
- - reg: Should contain address of the controller on the LBC bus. The detail
- was described in Documentation/devicetree/bindings/powerpc/fsl/lbc.txt
-
-Examples:
-display@2,0 {
- compatible = "solomon,ssd1289fb";
- reg = <0x2 0x0000 0x0004>;
-};
+++ /dev/null
-* Solomon SSD1307 Framebuffer Driver
-
-Required properties:
- - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for
- now is i2c, and the supported chips are ssd1305, ssd1306 and ssd1307.
- - reg: Should contain address of the controller on the I2C bus. Most likely
- 0x3c or 0x3d
- - pwm: Should contain the pwm to use according to the OF device tree PWM
- specification [0]. Only required for the ssd1307.
- - reset-gpios: Should contain the GPIO used to reset the OLED display
- - solomon,height: Height in pixel of the screen driven by the controller
- - solomon,width: Width in pixel of the screen driven by the controller
- - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
- mapped to.
-
-Optional properties:
- - reset-active-low: Is the reset gpio is active on physical low?
- - solomon,segment-no-remap: Display needs normal (non-inverted) data column
- to segment mapping
- - solomon,com-seq: Display uses sequential COM pin configuration
- - solomon,com-lrremap: Display uses left-right COM pin remap
- - solomon,com-invdir: Display uses inverted COM pin scan direction
- - solomon,com-offset: Number of the COM pin wired to the first display line
- - solomon,prechargep1: Length of deselect period (phase 1) in clock cycles.
- - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles.
- This needs to be the higher, the higher the capacitance
- of the OLED's pixels is
-
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
-
-Examples:
-ssd1307: oled@3c {
- compatible = "solomon,ssd1307fb-i2c";
- reg = <0x3c>;
- pwms = <&pwm 4 3000>;
- reset-gpios = <&gpio2 7>;
- reset-active-low;
-};
-
-ssd1306: oled@3c {
- compatible = "solomon,ssd1306fb-i2c";
- reg = <0x3c>;
- pwms = <&pwm 4 3000>;
- reset-gpios = <&gpio2 7>;
- reset-active-low;
- solomon,com-lrremap;
- solomon,com-invdir;
- solomon,com-offset = <32>;
-};
+++ /dev/null
-THine Electronics THC63LVDM83D LVDS serializer
-----------------------------------------------
-
-The THC63LVDM83D is an LVDS serializer designed to support pixel data
-transmission between a host and a flat panel.
-
-Required properties:
-
-- compatible: Should be "thine,thc63lvdm83d"
-
-Optional properties:
-
-- pwdn-gpios: Power down control GPIO
-
-Required nodes:
-
-The THC63LVDM83D has two video ports. Their connections are modeled using the
-OFgraph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for CMOS/TTL input
-- Video port 1 for LVDS output
-
-
-Example
--------
-
- lvds_enc: encoder@0 {
- compatible = "thine,thc63lvdm83d";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- lvds_enc_in: endpoint@0 {
- remote-endpoint = <&rgb_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- lvds_enc_out: endpoint@0 {
- remote-endpoint = <&panel_in>;
- };
- };
- };
- };
+++ /dev/null
-Texas Instruments DRA7x Display Subsystem
-=========================================
-
-See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
-description about OMAP Display Subsystem bindings.
-
-DSS Core
---------
-
-Required properties:
-- compatible: "ti,dra7-dss"
-- reg: address and length of the register spaces for 'dss'
-- ti,hwmods: "dss_core"
-- clocks: handle to fclk
-- clock-names: "fck"
-- syscon: phandle to control module core syscon node
-
-Optional properties:
-
-Some DRA7xx SoCs have one dedicated video PLL, some have two. These properties
-can be used to describe the video PLLs:
-
-- reg: address and length of the register spaces for 'pll1_clkctrl',
- 'pll1', 'pll2_clkctrl', 'pll2'
-- clocks: handle to video1 pll clock and video2 pll clock
-- clock-names: "video1_clk" and "video2_clk"
-
-Required nodes:
-- DISPC
-
-Optional nodes:
-- DSS Submodules: HDMI
-- Video port for DPI output
-
-DPI Endpoint required properties:
-- data-lines: number of lines used
-
-
-DISPC
------
-
-Required properties:
-- compatible: "ti,dra7-dispc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_dispc"
-- interrupts: the DISPC interrupt
-- clocks: handle to fclk
-- clock-names: "fck"
-
-HDMI
-----
-
-Required properties:
-- compatible: "ti,dra7-hdmi"
-- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
- 'core'
-- reg-names: "wp", "pll", "phy", "core"
-- interrupts: the HDMI interrupt line
-- ti,hwmods: "dss_hdmi"
-- vdda-supply: vdda power supply
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-Optional nodes:
-- Video port for HDMI output
-
-HDMI Endpoint optional properties:
-- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
- D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
+++ /dev/null
-Texas Instruments OMAP Display Subsystem
-========================================
-
-Generic Description
--------------------
-
-This document is a generic description of the OMAP Display Subsystem bindings.
-Binding details for each OMAP SoC version are described in respective binding
-documentation.
-
-The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and
-a number of encoder modules. All DSS versions contain DSS Core and DISPC, but
-the encoder modules vary.
-
-The DSS Core is the parent of the other DSS modules, and manages clock routing,
-integration to the SoC, etc.
-
-DISPC is the display controller, which reads pixels from the memory and outputs
-a RGB pixel stream to encoders.
-
-The encoder modules encode the received RGB pixel stream to a video output like
-HDMI, MIPI DPI, etc.
-
-Video Ports
------------
-
-The DSS Core and the encoders have video port outputs. The structure of the
-video ports is described in Documentation/devicetree/bindings/graph.txt,
-and the properties for the ports and endpoints for each encoder are
-described in the SoC's DSS binding documentation.
-
-The video ports are used to describe the connections to external hardware, like
-panels or external encoders.
-
-Aliases
--------
-
-The board dts file may define aliases for displays to assign "displayX" style
-name for each display. If no aliases are defined, a semi-random number is used
-for the display.
-
-Example
--------
-
-A shortened example of the DSS description for OMAP4, with non-relevant parts
-removed, defined in omap4.dtsi:
-
-dss: dss@58000000 {
- compatible = "ti,omap4-dss";
- reg = <0x58000000 0x80>;
- status = "disabled";
- ti,hwmods = "dss_core";
- clocks = <&dss_dss_clk>;
- clock-names = "fck";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dispc@58001000 {
- compatible = "ti,omap4-dispc";
- reg = <0x58001000 0x1000>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- ti,hwmods = "dss_dispc";
- clocks = <&dss_dss_clk>;
- clock-names = "fck";
- };
-
- hdmi: encoder@58006000 {
- compatible = "ti,omap4-hdmi";
- reg = <0x58006000 0x200>,
- <0x58006200 0x100>,
- <0x58006300 0x100>,
- <0x58006400 0x1000>;
- reg-names = "wp", "pll", "phy", "core";
- interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- ti,hwmods = "dss_hdmi";
- clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
- clock-names = "fck", "sys_clk";
- };
-};
-
-A shortened example of the board description for OMAP4 Panda board, defined in
-omap4-panda.dts.
-
-The Panda board has a DVI and a HDMI connector, and the board contains a TFP410
-chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level
-shifter). The video pipelines for the connectors are formed as follows:
-
-DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector
-OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector
-
-/ {
- aliases {
- display0 = &dvi0;
- display1 = &hdmi0;
- };
-
- tfp410: encoder@0 {
- compatible = "ti,tfp410";
- gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
-
- pinctrl-names = "default";
- pinctrl-0 = <&tfp410_pins>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tfp410_in: endpoint@0 {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tfp410_out: endpoint@0 {
- remote-endpoint = <&dvi_connector_in>;
- };
- };
- };
- };
-
- dvi0: connector@0 {
- compatible = "dvi-connector";
- label = "dvi";
-
- i2c-bus = <&i2c3>;
-
- port {
- dvi_connector_in: endpoint {
- remote-endpoint = <&tfp410_out>;
- };
- };
- };
-
- tpd12s015: encoder@1 {
- compatible = "ti,tpd12s015";
-
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
- gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
- <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
- <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint@0 {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint@0 {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
-
- hdmi0: connector@1 {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-};
-
-&dss {
- status = "ok";
-
- pinctrl-names = "default";
- pinctrl-0 = <&dss_dpi_pins>;
-
- port {
- dpi_out: endpoint {
- remote-endpoint = <&tfp410_in>;
- data-lines = <24>;
- };
- };
-};
-
-&hdmi {
- status = "ok";
- vdda-supply = <&vdac>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&dss_hdmi_pins>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
-};
+++ /dev/null
-Texas Instruments OMAP2 Display Subsystem
-=========================================
-
-See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
-description about OMAP Display Subsystem bindings.
-
-DSS Core
---------
-
-Required properties:
-- compatible: "ti,omap2-dss"
-- reg: address and length of the register space
-- ti,hwmods: "dss_core"
-
-Optional nodes:
-- Video port for DPI output
-
-DPI Endpoint required properties:
-- data-lines: number of lines used
-
-
-DISPC
------
-
-Required properties:
-- compatible: "ti,omap2-dispc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_dispc"
-- interrupts: the DISPC interrupt
-
-
-RFBI
-----
-
-Required properties:
-- compatible: "ti,omap2-rfbi"
-- reg: address and length of the register space
-- ti,hwmods: "dss_rfbi"
-
-
-VENC
-----
-
-Required properties:
-- compatible: "ti,omap2-venc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_venc"
-- vdda-supply: power supply for DAC
-
-VENC Endpoint required properties:
-
-Required properties:
-- ti,invert-polarity: invert the polarity of the video signal
-- ti,channels: 1 for composite, 2 for s-video
+++ /dev/null
-Texas Instruments OMAP3 Display Subsystem
-=========================================
-
-See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
-description about OMAP Display Subsystem bindings.
-
-DSS Core
---------
-
-Required properties:
-- compatible: "ti,omap3-dss"
-- reg: address and length of the register space
-- ti,hwmods: "dss_core"
-- clocks: handle to fclk
-- clock-names: "fck"
-
-Optional nodes:
-- Video ports:
- - Port 0: DPI output
- - Port 1: SDI output
-
-DPI Endpoint required properties:
-- data-lines: number of lines used
-
-SDI Endpoint required properties:
-- datapairs: number of datapairs used
-
-
-DISPC
------
-
-Required properties:
-- compatible: "ti,omap3-dispc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_dispc"
-- interrupts: the DISPC interrupt
-- clocks: handle to fclk
-- clock-names: "fck"
-
-
-RFBI
-----
-
-Required properties:
-- compatible: "ti,omap3-rfbi"
-- reg: address and length of the register space
-- ti,hwmods: "dss_rfbi"
-- clocks: handles to fclk and iclk
-- clock-names: "fck", "ick"
-
-
-VENC
-----
-
-Required properties:
-- compatible: "ti,omap3-venc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_venc"
-- vdda-supply: power supply for DAC
-- clocks: handle to fclk
-- clock-names: "fck"
-
-VENC Endpoint required properties:
-- ti,invert-polarity: invert the polarity of the video signal
-- ti,channels: 1 for composite, 2 for s-video
-
-
-DSI
----
-
-Required properties:
-- compatible: "ti,omap3-dsi"
-- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
-- reg-names: "proto", "phy", "pll"
-- interrupts: the DSI interrupt line
-- ti,hwmods: "dss_dsi1"
-- vdd-supply: power supply for DSI
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-DSI Endpoint required properties:
-- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
- DATA1+, DATA1-, ...
+++ /dev/null
-Texas Instruments OMAP4 Display Subsystem
-=========================================
-
-See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
-description about OMAP Display Subsystem bindings.
-
-DSS Core
---------
-
-Required properties:
-- compatible: "ti,omap4-dss"
-- reg: address and length of the register space
-- ti,hwmods: "dss_core"
-- clocks: handle to fclk
-- clock-names: "fck"
-
-Required nodes:
-- DISPC
-
-Optional nodes:
-- DSS Submodules: RFBI, VENC, DSI, HDMI
-- Video port for DPI output
-
-DPI Endpoint required properties:
-- data-lines: number of lines used
-
-
-DISPC
------
-
-Required properties:
-- compatible: "ti,omap4-dispc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_dispc"
-- interrupts: the DISPC interrupt
-- clocks: handle to fclk
-- clock-names: "fck"
-
-
-RFBI
-----
-
-Required properties:
-- compatible: "ti,omap4-rfbi"
-- reg: address and length of the register space
-- ti,hwmods: "dss_rfbi"
-- clocks: handles to fclk and iclk
-- clock-names: "fck", "ick"
-
-Optional nodes:
-- Video port for RFBI output
-- RFBI controlled peripherals
-
-
-VENC
-----
-
-Required properties:
-- compatible: "ti,omap4-venc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_venc"
-- vdda-supply: power supply for DAC
-- clocks: handle to fclk
-- clock-names: "fck"
-
-Optional nodes:
-- Video port for VENC output
-
-VENC Endpoint required properties:
-- ti,invert-polarity: invert the polarity of the video signal
-- ti,channels: 1 for composite, 2 for s-video
-
-
-DSI
----
-
-Required properties:
-- compatible: "ti,omap4-dsi"
-- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
-- reg-names: "proto", "phy", "pll"
-- interrupts: the DSI interrupt line
-- ti,hwmods: "dss_dsi1" or "dss_dsi2"
-- vdd-supply: power supply for DSI
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-Optional nodes:
-- Video port for DSI output
-- DSI controlled peripherals
-
-DSI Endpoint required properties:
-- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
- DATA1+, DATA1-, ...
-
-
-HDMI
-----
-
-Required properties:
-- compatible: "ti,omap4-hdmi"
-- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
- 'core'
-- reg-names: "wp", "pll", "phy", "core"
-- interrupts: the HDMI interrupt line
-- ti,hwmods: "dss_hdmi"
-- vdda-supply: vdda power supply
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-Optional nodes:
-- Video port for HDMI output
-
-HDMI Endpoint optional properties:
-- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
- D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
+++ /dev/null
-Texas Instruments OMAP5 Display Subsystem
-=========================================
-
-See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
-description about OMAP Display Subsystem bindings.
-
-DSS Core
---------
-
-Required properties:
-- compatible: "ti,omap5-dss"
-- reg: address and length of the register space
-- ti,hwmods: "dss_core"
-- clocks: handle to fclk
-- clock-names: "fck"
-
-Required nodes:
-- DISPC
-
-Optional nodes:
-- DSS Submodules: RFBI, DSI, HDMI
-- Video port for DPI output
-
-DPI Endpoint required properties:
-- data-lines: number of lines used
-
-
-DISPC
------
-
-Required properties:
-- compatible: "ti,omap5-dispc"
-- reg: address and length of the register space
-- ti,hwmods: "dss_dispc"
-- interrupts: the DISPC interrupt
-- clocks: handle to fclk
-- clock-names: "fck"
-
-
-RFBI
-----
-
-Required properties:
-- compatible: "ti,omap5-rfbi"
-- reg: address and length of the register space
-- ti,hwmods: "dss_rfbi"
-- clocks: handles to fclk and iclk
-- clock-names: "fck", "ick"
-
-Optional nodes:
-- Video port for RFBI output
-- RFBI controlled peripherals
-
-
-DSI
----
-
-Required properties:
-- compatible: "ti,omap5-dsi"
-- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
-- reg-names: "proto", "phy", "pll"
-- interrupts: the DSI interrupt line
-- ti,hwmods: "dss_dsi1" or "dss_dsi2"
-- vdd-supply: power supply for DSI
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-Optional nodes:
-- Video port for DSI output
-- DSI controlled peripherals
-
-DSI Endpoint required properties:
-- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
- DATA1+, DATA1-, ...
-
-
-HDMI
-----
-
-Required properties:
-- compatible: "ti,omap5-hdmi"
-- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
- 'core'
-- reg-names: "wp", "pll", "phy", "core"
-- interrupts: the HDMI interrupt line
-- ti,hwmods: "dss_hdmi"
-- vdda-supply: vdda power supply
-- clocks: handles to fclk and pll clock
-- clock-names: "fck", "sys_clk"
-
-Optional nodes:
-- Video port for HDMI output
-
-HDMI Endpoint optional properties:
-- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-,
- D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7)
+++ /dev/null
-OPA362 analog video amplifier
-
-Required properties:
-- compatible: "ti,opa362"
-- enable-gpios: enable/disable output gpio
-
-Required node:
-- Video port 0 for opa362 input
-- Video port 1 for opa362 output
-
-Example:
-
-tv_amp: opa362 {
- compatible = "ti,opa362";
- enable-gpios = <&gpio1 23 0>; /* GPIO to enable video out amplifier */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- opa_in: endpoint@0 {
- remote-endpoint = <&venc_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- opa_out: endpoint@0 {
- remote-endpoint = <&tv_connector_in>;
- };
- };
- };
-};
-
-
-
+++ /dev/null
-TFP410 DPI to DVI encoder
-=========================
-
-Required properties:
-- compatible: "ti,tfp410"
-
-Optional properties:
-- powerdown-gpios: power-down gpio
-
-Required nodes:
-- Video port 0 for DPI input
-- Video port 1 for DVI output
-
-Example
--------
-
-tfp410: encoder@0 {
- compatible = "ti,tfp410";
- powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tfp410_in: endpoint@0 {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tfp410_out: endpoint@0 {
- remote-endpoint = <&dvi_connector_in>;
- };
- };
- };
-};
+++ /dev/null
-TPD12S015 HDMI level shifter and ESD protection chip
-====================================================
-
-Required properties:
-- compatible: "ti,tpd12s015"
-
-Optional properties:
-- gpios: CT CP HPD, LS OE and HPD gpios
-
-Required nodes:
-- Video port 0 for HDMI input
-- Video port 1 for HDMI output
-
-Example
--------
-
-tpd12s015: encoder@1 {
- compatible = "ti,tpd12s015";
-
- gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
- <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
- <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint@0 {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint@0 {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
-};
+++ /dev/null
-Toppoly TD028TTEC1 Panel
-========================
-
-Required properties:
-- compatible: "toppoly,td028ttec1"
-
-Optional properties:
-- label: a symbolic name for the panel
-
-Required nodes:
-- Video port for DPI input
-
-Example
--------
-
-lcd-panel: td028ttec1@0 {
- compatible = "toppoly,td028ttec1";
- reg = <0>;
- spi-max-frequency = <100000>;
- spi-cpol;
- spi-cpha;
-
- label = "lcd";
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-};
-
+++ /dev/null
-TPO TD043MTEA1 Panel
-====================
-
-Required properties:
-- compatible: "tpo,td043mtea1"
-- reset-gpios: panel reset gpio
-
-Optional properties:
-- label: a symbolic name for the panel
-
-Required nodes:
-- Video port for DPI input
-
-Example
--------
-
-lcd-panel: panel@0 {
- compatible = "tpo,td043mtea1";
- reg = <0>;
- spi-max-frequency = <100000>;
- spi-cpol;
- spi-cpha;
-
- label = "lcd";
-
- reset-gpios = <&gpio7 7 0>;
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-};
+++ /dev/null
-VGA Connector
-=============
-
-Required properties:
-
-- compatible: "vga-connector"
-
-Optional properties:
-
-- label: a symbolic name for the connector corresponding to a hardware label
-- ddc-i2c-bus: phandle to the I2C bus that is connected to VGA DDC
-
-Required nodes:
-
-The VGA connector internal connections are modeled using the OF graph bindings
-specified in Documentation/devicetree/bindings/graph.txt.
-
-The VGA connector has a single port that must be connected to a video source
-port.
-
-
-Example
--------
-
-vga0: connector@0 {
- compatible = "vga-connector";
- label = "vga";
-
- ddc-i2c-bus = <&i2c3>;
-
- port {
- vga_connector_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
-};
+++ /dev/null
-VIA VT8500 Framebuffer
------------------------------------------------------
-
-Required properties:
-- compatible : "via,vt8500-fb"
-- reg : Should contain 1 register ranges(address and length)
-- interrupts : framebuffer controller interrupt
-- bits-per-pixel : bit depth of framebuffer (16 or 32)
-
-Required subnodes:
-- display-timings: see display-timing.txt for information
-
-Example:
-
- fb@d8050800 {
- compatible = "via,vt8500-fb";
- reg = <0xd800e400 0x400>;
- interrupts = <12>;
- bits-per-pixel = <16>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: 800x480 {
- clock-frequency = <0>; /* unused but required */
- hactive = <800>;
- vactive = <480>;
- hfront-porch = <40>;
- hback-porch = <88>;
- hsync-len = <0>;
- vback-porch = <32>;
- vfront-porch = <11>;
- vsync-len = <1>;
- };
- };
- };
-
+++ /dev/null
-VIA/Wondermedia Graphics Engine Controller
------------------------------------------------------
-
-Required properties:
-- compatible : "wm,prizm-ge-rops"
-- reg : Should contain 1 register ranges(address and length)
-
-Example:
-
- ge_rops@d8050400 {
- compatible = "wm,prizm-ge-rops";
- reg = <0xd8050400 0x100>;
- };
+++ /dev/null
-Wondermedia WM8505 Framebuffer
------------------------------------------------------
-
-Required properties:
-- compatible : "wm,wm8505-fb"
-- reg : Should contain 1 register ranges(address and length)
-- bits-per-pixel : bit depth of framebuffer (16 or 32)
-
-Required subnodes:
-- display-timings: see display-timing.txt for information
-
-Example:
-
- fb@d8051700 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8051700 0x200>;
- bits-per-pixel = <16>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: 800x480 {
- clock-frequency = <0>; /* unused but required */
- hactive = <800>;
- vactive = <480>;
- hfront-porch = <40>;
- hback-porch = <88>;
- hsync-len = <0>;
- vback-porch = <32>;
- vfront-porch = <11>;
- vsync-len = <1>;
- };
- };
- };
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff