netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYs
authorDavid Daney <david.daney@cavium.com>
Wed, 27 Jun 2012 07:33:38 +0000 (07:33 +0000)
committerDavid S. Miller <davem@davemloft.net>
Thu, 28 Jun 2012 04:23:25 +0000 (21:23 -0700)
Add a driver for BCM8706 and BCM8727 devices.  These are a 10Gig PHYs
which use MII_ADDR_C45 addressing.  They are always 10G full duplex, so
there is no autonegotiation.  All we do is report link state and send
interrupts when it changes.

If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.

Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt [new file with mode: 0644]
drivers/net/phy/Kconfig
drivers/net/phy/Makefile
drivers/net/phy/bcm87xx.c [new file with mode: 0644]

diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
new file mode 100644 (file)
index 0000000..7c86d5e
--- /dev/null
@@ -0,0 +1,29 @@
+The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs.  They
+have these bindings in addition to the standard PHY bindings.
+
+Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and
+            "ethernet-phy-ieee802.3-c45"
+
+Optional Properties:
+
+- broadcom,c45-reg-init : one of more sets of 4 cells.  The first cell
+  is the MDIO Manageable Device (MMD) address, the second a register
+  address within the MMD, the third cell contains a mask to be ANDed
+  with the existing register value, and the fourth cell is ORed with
+  he result to yield the new register value.  If the third cell has a
+  value of zero, no read of the existing value is performed.
+
+Example:
+
+       ethernet-phy@5 {
+               reg = <5>;
+               compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45";
+               interrupt-parent = <&gpio>;
+               interrupts = <12 8>; /* Pin 12, active low */
+               /*
+                * Set PMD Digital Control Register for
+                * GPIO[1] Tx/Rx
+                * GPIO[0] R64 Sync Acquired
+                */
+               broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>;
+       };
index 944cdfb80fe491686d4798a813099aaf4637617d..3090dc65a6f131541d055a17cb96e7c8c3e9d06a 100644 (file)
@@ -67,6 +67,11 @@ config BCM63XX_PHY
        ---help---
          Currently supports the 6348 and 6358 PHYs.
 
+config BCM87XX_PHY
+       tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
+       help
+         Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
+
 config ICPLUS_PHY
        tristate "Drivers for ICPlus PHYs"
        ---help---
index f51af688ef8b70add3c9f0d161baa25ba40201ec..6d2dc6c94f2e4bc30c41729b9c9d2cdbfe4de120 100644 (file)
@@ -12,6 +12,7 @@ obj-$(CONFIG_SMSC_PHY)                += smsc.o
 obj-$(CONFIG_VITESSE_PHY)      += vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)     += broadcom.o
 obj-$(CONFIG_BCM63XX_PHY)      += bcm63xx.o
+obj-$(CONFIG_BCM87XX_PHY)      += bcm87xx.o
 obj-$(CONFIG_ICPLUS_PHY)       += icplus.o
 obj-$(CONFIG_REALTEK_PHY)      += realtek.o
 obj-$(CONFIG_LSI_ET1011C_PHY)  += et1011c.o
diff --git a/drivers/net/phy/bcm87xx.c b/drivers/net/phy/bcm87xx.c
new file mode 100644 (file)
index 0000000..f5f0562
--- /dev/null
@@ -0,0 +1,238 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 - 2012 Cavium, Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+
+#define PHY_ID_BCM8706 0x0143bdc1
+#define PHY_ID_BCM8727 0x0143bff0
+
+#define BCM87XX_PMD_RX_SIGNAL_DETECT   (MII_ADDR_C45 | 0x1000a)
+#define BCM87XX_10GBASER_PCS_STATUS    (MII_ADDR_C45 | 0x30020)
+#define BCM87XX_XGXS_LANE_STATUS       (MII_ADDR_C45 | 0x40018)
+
+#define BCM87XX_LASI_CONTROL (MII_ADDR_C45 | 0x39002)
+#define BCM87XX_LASI_STATUS (MII_ADDR_C45 | 0x39005)
+
+#if IS_ENABLED(CONFIG_OF_MDIO)
+/* Set and/or override some configuration registers based on the
+ * marvell,reg-init property stored in the of_node for the phydev.
+ *
+ * broadcom,c45-reg-init = <devid reg mask value>,...;
+ *
+ * There may be one or more sets of <devid reg mask value>:
+ *
+ * devid: which sub-device to use.
+ * reg: the register.
+ * mask: if non-zero, ANDed with existing register value.
+ * value: ORed with the masked value and written to the regiser.
+ *
+ */
+static int bcm87xx_of_reg_init(struct phy_device *phydev)
+{
+       const __be32 *paddr;
+       const __be32 *paddr_end;
+       int len, ret;
+
+       if (!phydev->dev.of_node)
+               return 0;
+
+       paddr = of_get_property(phydev->dev.of_node,
+                               "broadcom,c45-reg-init", &len);
+       if (!paddr)
+               return 0;
+
+       paddr_end = paddr + (len /= sizeof(*paddr));
+
+       ret = 0;
+
+       while (paddr + 3 < paddr_end) {
+               u16 devid       = be32_to_cpup(paddr++);
+               u16 reg         = be32_to_cpup(paddr++);
+               u16 mask        = be32_to_cpup(paddr++);
+               u16 val_bits    = be32_to_cpup(paddr++);
+               int val;
+               u32 regnum = MII_ADDR_C45 | (devid << 16) | reg;
+               val = 0;
+               if (mask) {
+                       val = phy_read(phydev, regnum);
+                       if (val < 0) {
+                               ret = val;
+                               goto err;
+                       }
+                       val &= mask;
+               }
+               val |= val_bits;
+
+               ret = phy_write(phydev, regnum, val);
+               if (ret < 0)
+                       goto err;
+       }
+err:
+       return ret;
+}
+#else
+static int bcm87xx_of_reg_init(struct phy_device *phydev)
+{
+       return 0;
+}
+#endif /* CONFIG_OF_MDIO */
+
+static int bcm87xx_config_init(struct phy_device *phydev)
+{
+       phydev->supported = SUPPORTED_10000baseR_FEC;
+       phydev->advertising = ADVERTISED_10000baseR_FEC;
+       phydev->state = PHY_NOLINK;
+
+       bcm87xx_of_reg_init(phydev);
+
+       return 0;
+}
+
+static int bcm87xx_config_aneg(struct phy_device *phydev)
+{
+       return -EINVAL;
+}
+
+static int bcm87xx_read_status(struct phy_device *phydev)
+{
+       int rx_signal_detect;
+       int pcs_status;
+       int xgxs_lane_status;
+
+       rx_signal_detect = phy_read(phydev, BCM87XX_PMD_RX_SIGNAL_DETECT);
+       if (rx_signal_detect < 0)
+               return rx_signal_detect;
+
+       if ((rx_signal_detect & 1) == 0)
+               goto no_link;
+
+       pcs_status = phy_read(phydev, BCM87XX_10GBASER_PCS_STATUS);
+       if (pcs_status < 0)
+               return pcs_status;
+
+       if ((pcs_status & 1) == 0)
+               goto no_link;
+
+       xgxs_lane_status = phy_read(phydev, BCM87XX_XGXS_LANE_STATUS);
+       if (xgxs_lane_status < 0)
+               return xgxs_lane_status;
+
+       if ((xgxs_lane_status & 0x1000) == 0)
+               goto no_link;
+
+       phydev->speed = 10000;
+       phydev->link = 1;
+       phydev->duplex = 1;
+       return 0;
+
+no_link:
+       phydev->link = 0;
+       return 0;
+}
+
+static int bcm87xx_config_intr(struct phy_device *phydev)
+{
+       int reg, err;
+
+       reg = phy_read(phydev, BCM87XX_LASI_CONTROL);
+
+       if (reg < 0)
+               return reg;
+
+       if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+               reg |= 1;
+       else
+               reg &= ~1;
+
+       err = phy_write(phydev, BCM87XX_LASI_CONTROL, reg);
+       return err;
+}
+
+static int bcm87xx_did_interrupt(struct phy_device *phydev)
+{
+       int reg;
+
+       reg = phy_read(phydev, BCM87XX_LASI_STATUS);
+
+       if (reg < 0) {
+               dev_err(&phydev->dev,
+                       "Error: Read of BCM87XX_LASI_STATUS failed: %d\n", reg);
+               return 0;
+       }
+       return (reg & 1) != 0;
+}
+
+static int bcm87xx_ack_interrupt(struct phy_device *phydev)
+{
+       /* Reading the LASI status clears it. */
+       bcm87xx_did_interrupt(phydev);
+       return 0;
+}
+
+static int bcm8706_match_phy_device(struct phy_device *phydev)
+{
+       return phydev->c45_ids.device_ids[4] == PHY_ID_BCM8706;
+}
+
+static int bcm8727_match_phy_device(struct phy_device *phydev)
+{
+       return phydev->c45_ids.device_ids[4] == PHY_ID_BCM8727;
+}
+
+static struct phy_driver bcm8706_driver = {
+       .phy_id         = PHY_ID_BCM8706,
+       .phy_id_mask    = 0xffffffff,
+       .name           = "Broadcom BCM8706",
+       .flags          = PHY_HAS_INTERRUPT,
+       .config_init    = bcm87xx_config_init,
+       .config_aneg    = bcm87xx_config_aneg,
+       .read_status    = bcm87xx_read_status,
+       .ack_interrupt  = bcm87xx_ack_interrupt,
+       .config_intr    = bcm87xx_config_intr,
+       .did_interrupt  = bcm87xx_did_interrupt,
+       .match_phy_device = bcm8706_match_phy_device,
+       .driver         = { .owner = THIS_MODULE },
+};
+
+static struct phy_driver bcm8727_driver = {
+       .phy_id         = PHY_ID_BCM8727,
+       .phy_id_mask    = 0xffffffff,
+       .name           = "Broadcom BCM8727",
+       .flags          = PHY_HAS_INTERRUPT,
+       .config_init    = bcm87xx_config_init,
+       .config_aneg    = bcm87xx_config_aneg,
+       .read_status    = bcm87xx_read_status,
+       .ack_interrupt  = bcm87xx_ack_interrupt,
+       .config_intr    = bcm87xx_config_intr,
+       .did_interrupt  = bcm87xx_did_interrupt,
+       .match_phy_device = bcm8727_match_phy_device,
+       .driver         = { .owner = THIS_MODULE },
+};
+
+static int __init bcm87xx_init(void)
+{
+       int ret;
+
+       ret = phy_driver_register(&bcm8706_driver);
+       if (ret)
+               goto err;
+
+       ret = phy_driver_register(&bcm8727_driver);
+err:
+       return ret;
+}
+module_init(bcm87xx_init);
+
+static void __exit bcm87xx_exit(void)
+{
+       phy_driver_unregister(&bcm8706_driver);
+       phy_driver_unregister(&bcm8727_driver);
+}
+module_exit(bcm87xx_exit);