#include "mpc83xx.h"
#define BCSR5_INT_USB 0x02
-/* Note: This is only for PB, not for PB+PIB
- * On PB only port0 is connected using ULPI */
-static int mpc834x_usb_cfg(void)
+static int mpc834xemds_usb_cfg(void)
{
- unsigned long sccr, sicrl;
- void __iomem *immap;
+ struct device_node *np;
void __iomem *bcsr_regs = NULL;
u8 bcsr5;
- struct device_node *np = NULL;
- int port0_is_dr = 0;
-
- if ((np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr")) != NULL)
- port0_is_dr = 1;
- if ((np = of_find_compatible_node(NULL, "usb", "fsl-usb2-mph")) != NULL){
- if (port0_is_dr) {
- printk(KERN_WARNING
- "There is only one USB port on PB board! \n");
- return -1;
- } else if (!port0_is_dr)
- /* No usb port enabled */
- return -1;
- }
-
- immap = ioremap(get_immrbase(), 0x1000);
- if (!immap)
- return -1;
-
- /* Configure clock */
- sccr = in_be32(immap + MPC83XX_SCCR_OFFS);
- if (port0_is_dr)
- sccr |= MPC83XX_SCCR_USB_DRCM_11; /* 1:3 */
- else
- sccr |= MPC83XX_SCCR_USB_MPHCM_11; /* 1:3 */
- out_be32(immap + MPC83XX_SCCR_OFFS, sccr);
-
- /* Configure Pin */
- sicrl = in_be32(immap + MPC83XX_SICRL_OFFS);
- /* set port0 only */
- if (port0_is_dr)
- sicrl |= MPC83XX_SICRL_USB0;
- else
- sicrl &= ~(MPC83XX_SICRL_USB0);
- out_be32(immap + MPC83XX_SICRL_OFFS, sicrl);
-
- iounmap(immap);
+ mpc834x_usb_cfg();
/* Map BCSR area */
np = of_find_node_by_name(NULL, "bcsr");
- if (np != 0) {
+ if (np) {
struct resource res;
of_address_to_resource(np, 0, &res);
ppc_md.pci_exclude_device = mpc83xx_exclude_device;
#endif
- mpc834x_usb_cfg();
+ mpc834xemds_usb_cfg();
}
static void __init mpc834x_mds_init_IRQ(void)
/* System Clock Control Register */
#define MPC83XX_SCCR_OFFS 0xA08
+#define MPC83XX_SCCR_USB_MASK 0x00f00000
#define MPC83XX_SCCR_USB_MPHCM_11 0x00c00000
#define MPC83XX_SCCR_USB_MPHCM_01 0x00400000
#define MPC83XX_SCCR_USB_MPHCM_10 0x00800000
/* system i/o configuration register low */
#define MPC83XX_SICRL_OFFS 0x114
-#define MPC83XX_SICRL_USB0 0x40000000
-#define MPC83XX_SICRL_USB1 0x20000000
+#define MPC834X_SICRL_USB_MASK 0x60000000
+#define MPC834X_SICRL_USB0 0x40000000
+#define MPC834X_SICRL_USB1 0x20000000
+#define MPC831X_SICRL_USB_MASK 0x00000c00
+#define MPC831X_SICRL_USB_ULPI 0x00000800
/* system i/o configuration register high */
#define MPC83XX_SICRH_OFFS 0x118
-#define MPC83XX_SICRH_USB_UTMI 0x00020000
+#define MPC834X_SICRH_USB_UTMI 0x00020000
+#define MPC831X_SICRH_USB_MASK 0x000000e0
+#define MPC831X_SICRH_USB_ULPI 0x000000a0
+
+/* USB Control Register */
+#define FSL_USB2_CONTROL_OFFS 0x500
+#define CONTROL_UTMI_PHY_EN 0x00000200
+#define CONTROL_REFSEL_48MHZ 0x00000080
+#define CONTROL_PHY_CLK_SEL_ULPI 0x00000400
+#define CONTROL_OTG_PORT 0x00000020
+
+/* USB PORTSC Registers */
+#define FSL_USB2_PORTSC1_OFFS 0x184
+#define FSL_USB2_PORTSC2_OFFS 0x188
+#define PORTSCX_PTW_16BIT 0x10000000
+#define PORTSCX_PTS_UTMI 0x00000000
+#define PORTSCX_PTS_ULPI 0x80000000
/*
* Declaration for the various functions exported by the
u_char bus, u_char devfn);
extern void mpc83xx_restart(char *cmd);
extern long mpc83xx_time_init(void);
+extern int mpc834x_usb_cfg(void);
+extern int mpc831x_usb_cfg(void);
#endif /* __MPC83XX_H__ */
--- /dev/null
+/*
+ * Freescale 83xx USB SOC setup code
+ *
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Author: Li Yang
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+
+#include <asm/io.h>
+#include <asm/prom.h>
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+
+#ifdef CONFIG_MPC834x
+int mpc834x_usb_cfg(void)
+{
+ unsigned long sccr, sicrl, sicrh;
+ void __iomem *immap;
+ struct device_node *np = NULL;
+ int port0_is_dr = 0, port1_is_dr = 0;
+ const void *prop, *dr_mode;
+
+ immap = ioremap(get_immrbase(), 0x1000);
+ if (!immap)
+ return -ENOMEM;
+
+ /* Read registers */
+ /* Note: DR and MPH must use the same clock setting in SCCR */
+ sccr = in_be32(immap + MPC83XX_SCCR_OFFS) & ~MPC83XX_SCCR_USB_MASK;
+ sicrl = in_be32(immap + MPC83XX_SICRL_OFFS) & ~MPC834X_SICRL_USB_MASK;
+ sicrh = in_be32(immap + MPC83XX_SICRH_OFFS) & ~MPC834X_SICRH_USB_UTMI;
+
+ np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr");
+ if (np) {
+ sccr |= MPC83XX_SCCR_USB_DRCM_11; /* 1:3 */
+
+ prop = of_get_property(np, "phy_type", NULL);
+ if (prop && (!strcmp(prop, "utmi") ||
+ !strcmp(prop, "utmi_wide"))) {
+ sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
+ sicrh |= MPC834X_SICRH_USB_UTMI;
+ port1_is_dr = 1;
+ } else if (prop && !strcmp(prop, "serial")) {
+ dr_mode = of_get_property(np, "dr_mode", NULL);
+ if (dr_mode && !strcmp(dr_mode, "otg")) {
+ sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
+ port1_is_dr = 1;
+ } else {
+ sicrl |= MPC834X_SICRL_USB0;
+ }
+ } else if (prop && !strcmp(prop, "ulpi")) {
+ sicrl |= MPC834X_SICRL_USB0;
+ } else {
+ printk(KERN_WARNING "834x USB PHY type not supported\n");
+ }
+ port0_is_dr = 1;
+ of_node_put(np);
+ }
+ np = of_find_compatible_node(NULL, "usb", "fsl-usb2-mph");
+ if (np) {
+ sccr |= MPC83XX_SCCR_USB_MPHCM_11; /* 1:3 */
+
+ prop = of_get_property(np, "port0", NULL);
+ if (prop) {
+ if (port0_is_dr)
+ printk(KERN_WARNING
+ "834x USB port0 can't be used by both DR and MPH!\n");
+ sicrl |= MPC834X_SICRL_USB0;
+ }
+ prop = of_get_property(np, "port1", NULL);
+ if (prop) {
+ if (port1_is_dr)
+ printk(KERN_WARNING
+ "834x USB port1 can't be used by both DR and MPH!\n");
+ sicrl |= MPC834X_SICRL_USB1;
+ }
+ of_node_put(np);
+ }
+
+ /* Write back */
+ out_be32(immap + MPC83XX_SCCR_OFFS, sccr);
+ out_be32(immap + MPC83XX_SICRL_OFFS, sicrl);
+ out_be32(immap + MPC83XX_SICRH_OFFS, sicrh);
+
+ iounmap(immap);
+ return 0;
+}
+#endif /* CONFIG_MPC834x */
+
+#ifdef CONFIG_PPC_MPC831x
+int mpc831x_usb_cfg(void)
+{
+ u32 temp;
+ void __iomem *immap, *usb_regs;
+ struct device_node *np = NULL;
+ const void *prop;
+ struct resource res;
+ int ret = 0;
+#ifdef CONFIG_USB_OTG
+ const void *dr_mode;
+#endif
+
+ np = of_find_compatible_node(NULL, "usb", "fsl-usb2-dr");
+ if (!np)
+ return -ENODEV;
+ prop = of_get_property(np, "phy_type", NULL);
+
+ /* Map IMMR space for pin and clock settings */
+ immap = ioremap(get_immrbase(), 0x1000);
+ if (!immap) {
+ of_node_put(np);
+ return -ENOMEM;
+ }
+
+ /* Configure clock */
+ temp = in_be32(immap + MPC83XX_SCCR_OFFS);
+ temp &= ~MPC83XX_SCCR_USB_MASK;
+ temp |= MPC83XX_SCCR_USB_DRCM_11; /* 1:3 */
+ out_be32(immap + MPC83XX_SCCR_OFFS, temp);
+
+ /* Configure pin mux for ULPI. There is no pin mux for UTMI */
+ if (!strcmp(prop, "ulpi")) {
+ temp = in_be32(immap + MPC83XX_SICRL_OFFS);
+ temp &= ~MPC831X_SICRL_USB_MASK;
+ temp |= MPC831X_SICRL_USB_ULPI;
+ out_be32(immap + MPC83XX_SICRL_OFFS, temp);
+
+ temp = in_be32(immap + MPC83XX_SICRH_OFFS);
+ temp &= ~MPC831X_SICRH_USB_MASK;
+ temp |= MPC831X_SICRH_USB_ULPI;
+ out_be32(immap + MPC83XX_SICRH_OFFS, temp);
+ }
+
+ iounmap(immap);
+
+ /* Map USB SOC space */
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret) {
+ of_node_put(np);
+ return ret;
+ }
+ usb_regs = ioremap(res.start, res.end - res.start + 1);
+
+ /* Using on-chip PHY */
+ if (!strcmp(prop, "utmi_wide") ||
+ !strcmp(prop, "utmi")) {
+ /* Set UTMI_PHY_EN, REFSEL to 48MHZ */
+ out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
+ CONTROL_UTMI_PHY_EN | CONTROL_REFSEL_48MHZ);
+ /* Using external UPLI PHY */
+ } else if (!strcmp(prop, "ulpi")) {
+ /* Set PHY_CLK_SEL to ULPI */
+ temp = CONTROL_PHY_CLK_SEL_ULPI;
+#ifdef CONFIG_USB_OTG
+ /* Set OTG_PORT */
+ dr_mode = of_get_property(np, "dr_mode", NULL);
+ if (dr_mode && !strcmp(dr_mode, "otg"))
+ temp |= CONTROL_OTG_PORT;
+#endif /* CONFIG_USB_OTG */
+ out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
+ } else {
+ printk(KERN_WARNING "831x USB PHY type not supported\n");
+ ret = -EINVAL;
+ }
+
+ iounmap(usb_regs);
+ of_node_put(np);
+ return ret;
+}
+#endif /* CONFIG_PPC_MPC831x */
projects / GitHub / LineageOS / android_kernel_samsung_universal7580.git / commitdiff