bi.dwAddress = swab32(blockidx->PageAddress);
uea_dbg(INS_TO_USBDEV(sc),
- "sending block %u for DSP page %u size %u adress %x\n",
+ "sending block %u for DSP page %u size %u address %x\n",
blockno, pageno, blocksize, le32_to_cpu(blockidx->PageAddress));
/* send block info through the IDMA pipe */
}
if (data_interface_num != call_interface_num)
- dev_dbg(&intf->dev,"Seperate call control interface. That is not fully supported.\n");
+ dev_dbg(&intf->dev,"Separate call control interface. That is not fully supported.\n");
skip_normal_probe:
#define AT91_UDP_RXRSM (1 << 9) /* USB Resume Interrupt Status */
#define AT91_UDP_EXTRSM (1 << 10) /* External Resume Interrupt Status [AT91RM9200 only] */
#define AT91_UDP_SOFINT (1 << 11) /* Start of Frame Interrupt Status */
-#define AT91_UDP_ENDBUSRES (1 << 12) /* End of Bus Reset Interrpt Status */
+#define AT91_UDP_ENDBUSRES (1 << 12) /* End of Bus Reset Interrupt Status */
#define AT91_UDP_WAKEUP (1 << 13) /* USB Wakeup Interrupt Status [AT91RM9200 only] */
#define AT91_UDP_ICR 0x20 /* Interrupt Clear Register */
spin_lock_irqsave(&udc->lock, flags);
- /* ------basic driver infomation ---- */
+ /* ------basic driver information ---- */
t = scnprintf(next, size,
DRIVER_DESC "\n"
"%s version: %s\n"
/* STATUS for zero length DATA stages is
* always an IN ... even for IN transfers,
- * a wierd case which seem to stall OMAP.
+ * a weird case which seem to stall OMAP.
*/
UDC_EP_NUM_REG = (UDC_EP_SEL|UDC_EP_DIR);
UDC_CTRL_REG = UDC_CLR_EP;
#include "ehci-fsl.h"
-/* FIXME: Power Managment is un-ported so temporarily disable it */
+/* FIXME: Power Management is un-ported so temporarily disable it */
#undef CONFIG_PM
/* PCI-based HCs are common, but plenty of non-PCI HCs are used too */
* low/fullspeed transfer can "carry over" from one uframe to the next,
* since the TT just performs downstream transfers in sequence.
*
- * For example two seperate 100 usec transfers can start in the same uframe,
+ * For example two separate 100 usec transfers can start in the same uframe,
* and the second one would "carry over" 75 usecs into the next uframe.
*/
static void
struct r8a66597_pipe_info {
u16 pipenum;
- u16 address; /* R8A66597 HCD usb addres */
+ u16 address; /* R8A66597 HCD usb address */
u16 epnum;
u16 maxpacket;
u16 type;
usb_kill_urb(urb);
retval = -ETIMEDOUT;
} else {
- /* URB completed within timout */
+ /* URB completed within timeout */
retval = urb->status;
readbytes = urb->actual_length;
}
len += vary;
/* [real world] the "zero bytes IN" case isn't really used.
- * hardware can easily trip up in this wierd case, since its
+ * hardware can easily trip up in this weird case, since its
* status stage is IN, not OUT like other ep0in transfers.
*/
if (len > length)
*
* This function will block the close until one of the following:
* 1. Response to our Chase comes from Edgeport
- * 2. A timout of 10 seconds without activity has expired
+ * 2. A timeout of 10 seconds without activity has expired
* (1K of Edgeport data @ 2400 baud ==> 4 sec to empty)
*
************************************************************************/
return;
}
} else {
- // Reset timout value back to 10 seconds
+ // Reset timeout value back to 10 seconds
dbg("%s - Last %d, Current %d", __FUNCTION__, lastCredits, edge_port->txCredits);
loop = 10;
}
* This function will block the close until one of the following:
* 1. TX count are 0
* 2. The edgeport has stopped
- * 3. A timout of 3 seconds without activity has expired
+ * 3. A timeout of 3 seconds without activity has expired
*
************************************************************************/
static void block_until_tx_empty (struct edgeport_port *edge_port)
return;
}
} else {
- // Reset timout value back to seconds
+ // Reset timeout value back to seconds
loop = 30;
}
}
* This function will block the close until one of the following:
* 1. TX count are 0
* 2. The mos7840 has stopped
- * 3. A timout of 3 seconds without activity has expired
+ * 3. A timeout of 3 seconds without activity has expired
*
************************************************************************/
static void mos7840_block_until_tx_empty(struct moschip_port *mos7840_port)
dbg("%s - TIMEOUT", __FUNCTION__);
return;
} else {
- /* Reset timout value back to seconds */
+ /* Reset timeout value back to seconds */
wait = 30;
}
}
*
* This function will block the close until one of the following:
* 1. Response to our Chase comes from mos7840
- * 2. A timout of 10 seconds without activity has expired
+ * 2. A timeout of 10 seconds without activity has expired
* (1K of mos7840 data @ 2400 baud ==> 4 sec to empty)
*
************************************************************************/
dbg("%s - TIMEOUT", __FUNCTION__);
return;
} else {
- /* Reset timout value back to seconds */
+ /* Reset timeout value back to seconds */
wait = 10;
}
}
projects / GitHub / LineageOS / android_kernel_samsung_universal7580.git / commitdiff