* handshake done). There are two failure modes: "usec" have passed (major
* hardware flakeout), or the register reads as all-ones (hardware removed).
*/
-int xhci_handshake(struct xhci_hcd *xhci, void __iomem *ptr,
- u32 mask, u32 done, int usec)
+int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
{
u32 result;
xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Halt the HC");
xhci_quiesce(xhci);
- ret = xhci_handshake(xhci, &xhci->op_regs->status,
+ ret = xhci_handshake(&xhci->op_regs->status,
STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
if (!ret) {
xhci->xhc_state |= XHCI_STATE_HALTED;
* Wait for the HCHalted Status bit to be 0 to indicate the host is
* running.
*/
- ret = xhci_handshake(xhci, &xhci->op_regs->status,
+ ret = xhci_handshake(&xhci->op_regs->status,
STS_HALT, 0, XHCI_MAX_HALT_USEC);
if (ret == -ETIMEDOUT)
xhci_err(xhci, "Host took too long to start, "
command |= CMD_RESET;
writel(command, &xhci->op_regs->command);
- ret = xhci_handshake(xhci, &xhci->op_regs->command,
+ ret = xhci_handshake(&xhci->op_regs->command,
CMD_RESET, 0, 10 * 1000 * 1000);
if (ret)
return ret;
* xHCI cannot write to any doorbells or operational registers other
* than status until the "Controller Not Ready" flag is cleared.
*/
- ret = xhci_handshake(xhci, &xhci->op_regs->status,
+ ret = xhci_handshake(&xhci->op_regs->status,
STS_CNR, 0, 10 * 1000 * 1000);
for (i = 0; i < 2; ++i) {
/* Some chips from Fresco Logic need an extraordinary delay */
delay *= (xhci->quirks & XHCI_SLOW_SUSPEND) ? 10 : 1;
- if (xhci_handshake(xhci, &xhci->op_regs->status,
+ if (xhci_handshake(&xhci->op_regs->status,
STS_HALT, STS_HALT, delay)) {
xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
spin_unlock_irq(&xhci->lock);
command = readl(&xhci->op_regs->command);
command |= CMD_CSS;
writel(command, &xhci->op_regs->command);
- if (xhci_handshake(xhci, &xhci->op_regs->status,
+ if (xhci_handshake(&xhci->op_regs->status,
STS_SAVE, 0, 10 * 1000)) {
xhci_warn(xhci, "WARN: xHC save state timeout\n");
spin_unlock_irq(&xhci->lock);
command = readl(&xhci->op_regs->command);
command |= CMD_CRS;
writel(command, &xhci->op_regs->command);
- if (xhci_handshake(xhci, &xhci->op_regs->status,
+ if (xhci_handshake(&xhci->op_regs->status,
STS_RESTORE, 0, 10 * 1000)) {
xhci_warn(xhci, "WARN: xHC restore state timeout\n");
spin_unlock_irq(&xhci->lock);
command = readl(&xhci->op_regs->command);
command |= CMD_RUN;
writel(command, &xhci->op_regs->command);
- xhci_handshake(xhci, &xhci->op_regs->status, STS_HALT,
+ xhci_handshake(&xhci->op_regs->status, STS_HALT,
0, 250 * 1000);
/* step 5: walk topology and initialize portsc,