Input: edt-ft5x06 - add DT support
authorLothar Waßmann <LW@KARO-electronics.de>
Fri, 28 Mar 2014 16:23:02 +0000 (09:23 -0700)
committerDmitry Torokhov <dmitry.torokhov@gmail.com>
Fri, 28 Mar 2014 16:33:03 +0000 (09:33 -0700)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt [new file with mode: 0644]
drivers/input/touchscreen/edt-ft5x06.c

diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
new file mode 100644 (file)
index 0000000..76db967
--- /dev/null
@@ -0,0 +1,55 @@
+FocalTech EDT-FT5x06 Polytouch driver
+=====================================
+
+There are 3 variants of the chip for various touch panel sizes
+FT5206GE1  2.8" .. 3.8"
+FT5306DE4  4.3" .. 7"
+FT5406EE8  7"   .. 8.9"
+
+The software interface is identical for all those chips, so that
+currently there is no need for the driver to distinguish between the
+different chips. Nevertheless distinct compatible strings are used so
+that a distinction can be added if necessary without changing the DT
+bindings.
+
+
+Required properties:
+ - compatible:  "edt,edt-ft5206"
+           or:  "edt,edt-ft5306"
+           or:  "edt,edt-ft5406"
+
+ - reg:         I2C slave address of the chip (0x38)
+ - interrupt-parent: a phandle pointing to the interrupt controller
+                     serving the interrupt for this chip
+ - interrupts:       interrupt specification for the touchdetect
+                     interrupt
+
+Optional properties:
+ - reset-gpios: GPIO specification for the RESET input
+ - wake-gpios:  GPIO specification for the WAKE input
+
+ - pinctrl-names: should be "default"
+ - pinctrl-0:   a phandle pointing to the pin settings for the
+                control gpios
+
+ - threshold:   allows setting the "click"-threshold in the range
+                from 20 to 80.
+
+ - gain:        allows setting the sensitivity in the range from 0 to
+                31. Note that lower values indicate higher
+                sensitivity.
+
+ - offset:      allows setting the edge compensation in the range from
+                0 to 31.
+
+Example:
+       polytouch: edt-ft5x06@38 {
+               compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
+               reg = <0x38>;
+               pinctrl-names = "default";
+               pinctrl-0 = <&edt_ft5x06_pins>;
+               interrupt-parent = <&gpio2>;
+               interrupts = <5 0>;
+               reset-gpios = <&gpio2 6 1>;
+               wake-gpios = <&gpio4 9 0>;
+       };
index 155ab3ba84eefbd21698a238af5c3afa66427561..9d61f1e36b33b5b8509adb67c841e63048345471 100644 (file)
@@ -1,5 +1,6 @@
 /*
  * Copyright (C) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
+ * Lothar Waßmann <LW@KARO-electronics.de> (DT support)
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -33,6 +34,7 @@
 #include <linux/debugfs.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
+#include <linux/of_gpio.h>
 #include <linux/input/mt.h>
 #include <linux/input/edt-ft5x06.h>
 
@@ -65,6 +67,10 @@ struct edt_ft5x06_ts_data {
        u16 num_x;
        u16 num_y;
 
+       int reset_pin;
+       int irq_pin;
+       int wake_pin;
+
 #if defined(CONFIG_DEBUG_FS)
        struct dentry *debug_dir;
        u8 *raw_buffer;
@@ -614,24 +620,38 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
 #endif /* CONFIG_DEBUGFS */
 
 static int edt_ft5x06_ts_reset(struct i2c_client *client,
-                                        int reset_pin)
+                       struct edt_ft5x06_ts_data *tsdata)
 {
        int error;
 
-       if (gpio_is_valid(reset_pin)) {
+       if (gpio_is_valid(tsdata->wake_pin)) {
+               error = devm_gpio_request_one(&client->dev,
+                                       tsdata->wake_pin, GPIOF_OUT_INIT_LOW,
+                                       "edt-ft5x06 wake");
+               if (error) {
+                       dev_err(&client->dev,
+                               "Failed to request GPIO %d as wake pin, error %d\n",
+                               tsdata->wake_pin, error);
+                       return error;
+               }
+
+               mdelay(5);
+               gpio_set_value(tsdata->wake_pin, 1);
+       }
+       if (gpio_is_valid(tsdata->reset_pin)) {
                /* this pulls reset down, enabling the low active reset */
-               error = devm_gpio_request_one(&client->dev, reset_pin,
-                                             GPIOF_OUT_INIT_LOW,
-                                             "edt-ft5x06 reset");
+               error = devm_gpio_request_one(&client->dev,
+                                       tsdata->reset_pin, GPIOF_OUT_INIT_LOW,
+                                       "edt-ft5x06 reset");
                if (error) {
                        dev_err(&client->dev,
                                "Failed to request GPIO %d as reset pin, error %d\n",
-                               reset_pin, error);
+                               tsdata->reset_pin, error);
                        return error;
                }
 
                mdelay(50);
-               gpio_set_value(reset_pin, 1);
+               gpio_set_value(tsdata->reset_pin, 1);
                mdelay(100);
        }
 
@@ -672,6 +692,20 @@ static int edt_ft5x06_ts_identify(struct i2c_client *client,
            pdata->name <= edt_ft5x06_attr_##name.limit_high)           \
                edt_ft5x06_register_write(tsdata, reg, pdata->name)
 
+#define EDT_GET_PROP(name, reg) {                              \
+       u32 val;                                                \
+       if (of_property_read_u32(np, #name, &val) == 0)         \
+               edt_ft5x06_register_write(tsdata, reg, val);    \
+}
+
+static void edt_ft5x06_ts_get_dt_defaults(struct device_node *np,
+                                       struct edt_ft5x06_ts_data *tsdata)
+{
+       EDT_GET_PROP(threshold, WORK_REGISTER_THRESHOLD);
+       EDT_GET_PROP(gain, WORK_REGISTER_GAIN);
+       EDT_GET_PROP(offset, WORK_REGISTER_OFFSET);
+}
+
 static void
 edt_ft5x06_ts_get_defaults(struct edt_ft5x06_ts_data *tsdata,
                           const struct edt_ft5x06_platform_data *pdata)
@@ -699,6 +733,30 @@ edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
        tsdata->num_y = edt_ft5x06_register_read(tsdata, WORK_REGISTER_NUM_Y);
 }
 
+#ifdef CONFIG_OF
+static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+                               struct edt_ft5x06_ts_data *tsdata)
+{
+       struct device_node *np = dev->of_node;
+
+       /*
+        * irq_pin is not needed for DT setup.
+        * irq is associated via 'interrupts' property in DT
+        */
+       tsdata->irq_pin = -EINVAL;
+       tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
+       tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
+
+       return 0;
+}
+#else
+static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+                                       struct edt_ft5x06_ts_data *tsdata)
+{
+       return -ENODEV;
+}
+#endif
+
 static int edt_ft5x06_ts_probe(struct i2c_client *client,
                                         const struct i2c_device_id *id)
 {
@@ -711,32 +769,40 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 
        dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
 
+       tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
+       if (!tsdata) {
+               dev_err(&client->dev, "failed to allocate driver data.\n");
+               return -ENOMEM;
+       }
+
        if (!pdata) {
-               dev_err(&client->dev, "no platform data?\n");
-               return -EINVAL;
+               error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
+               if (error) {
+                       dev_err(&client->dev,
+                               "DT probe failed and no platform data present\n");
+                       return error;
+               }
+       } else {
+               tsdata->reset_pin = pdata->reset_pin;
+               tsdata->irq_pin = pdata->irq_pin;
+               tsdata->wake_pin = -EINVAL;
        }
 
-       error = edt_ft5x06_ts_reset(client, pdata->reset_pin);
+       error = edt_ft5x06_ts_reset(client, tsdata);
        if (error)
                return error;
 
-       if (gpio_is_valid(pdata->irq_pin)) {
-               error = devm_gpio_request_one(&client->dev, pdata->irq_pin,
-                                             GPIOF_IN, "edt-ft5x06 irq");
+       if (gpio_is_valid(tsdata->irq_pin)) {
+               error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
+                                       GPIOF_IN, "edt-ft5x06 irq");
                if (error) {
                        dev_err(&client->dev,
                                "Failed to request GPIO %d, error %d\n",
-                               pdata->irq_pin, error);
+                               tsdata->irq_pin, error);
                        return error;
                }
        }
 
-       tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
-       if (!tsdata) {
-               dev_err(&client->dev, "failed to allocate driver data.\n");
-               return -ENOMEM;
-       }
-
        input = devm_input_allocate_device(&client->dev);
        if (!input) {
                dev_err(&client->dev, "failed to allocate input device.\n");
@@ -754,7 +820,11 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
                return error;
        }
 
-       edt_ft5x06_ts_get_defaults(tsdata, pdata);
+       if (!pdata)
+               edt_ft5x06_ts_get_dt_defaults(client->dev.of_node, tsdata);
+       else
+               edt_ft5x06_ts_get_defaults(tsdata, pdata);
+
        edt_ft5x06_ts_get_parameters(tsdata);
 
        dev_dbg(&client->dev,
@@ -784,10 +854,10 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
        input_set_drvdata(input, tsdata);
        i2c_set_clientdata(client, tsdata);
 
-       error = devm_request_threaded_irq(&client->dev, client->irq,
-                                         NULL, edt_ft5x06_ts_isr,
-                                         IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
-                                         client->name, tsdata);
+       error = devm_request_threaded_irq(&client->dev, client->irq, NULL,
+                                       edt_ft5x06_ts_isr,
+                                       IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+                                       client->name, tsdata);
        if (error) {
                dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
                return error;
@@ -798,19 +868,21 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
                return error;
 
        error = input_register_device(input);
-       if (error) {
-               sysfs_remove_group(&client->dev.kobj, &edt_ft5x06_attr_group);
-               return error;
-       }
+       if (error)
+               goto err_remove_attrs;
 
        edt_ft5x06_ts_prepare_debugfs(tsdata, dev_driver_string(&client->dev));
        device_init_wakeup(&client->dev, 1);
 
        dev_dbg(&client->dev,
-               "EDT FT5x06 initialized: IRQ pin %d, Reset pin %d.\n",
-               pdata->irq_pin, pdata->reset_pin);
+               "EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
+               client->irq, tsdata->wake_pin, tsdata->reset_pin);
 
        return 0;
+
+err_remove_attrs:
+       sysfs_remove_group(&client->dev.kobj, &edt_ft5x06_attr_group);
+       return error;
 }
 
 static int edt_ft5x06_ts_remove(struct i2c_client *client)
@@ -854,10 +926,21 @@ static const struct i2c_device_id edt_ft5x06_ts_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
 
+#ifdef CONFIG_OF
+static const struct of_device_id edt_ft5x06_of_match[] = {
+       { .compatible = "edt,edt-ft5206", },
+       { .compatible = "edt,edt-ft5306", },
+       { .compatible = "edt,edt-ft5406", },
+       { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
+#endif
+
 static struct i2c_driver edt_ft5x06_ts_driver = {
        .driver = {
                .owner = THIS_MODULE,
                .name = "edt_ft5x06",
+               .of_match_table = of_match_ptr(edt_ft5x06_of_match),
                .pm = &edt_ft5x06_ts_pm_ops,
        },
        .id_table = edt_ft5x06_ts_id,