ide-tape: remove mtio.h related comments

Those are already in mtio.h.

Bart:
- undo 'unsigned int/unsigned long' -> 'uint/ulong' conversion

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index 8b9da8bb5cce7ce325ed6251d454339b3384257b..06d21bba4ea80e51ef6a4a6b192b6c7fb40285f4 100644 (file)
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -3152,69 +3152,20 @@ static int idetape_write_filemark (ide_drive_t *drive)
 }
 
 /*
- *     idetape_mtioctop is called from idetape_chrdev_ioctl when
- *     the general mtio MTIOCTOP ioctl is requested.
+ * Called from idetape_chrdev_ioctl when the general mtio MTIOCTOP ioctl is
+ * requested.
  *
- *     We currently support the following mtio.h operations:
+ * Note: MTBSF and MTBSFM are not supported when the tape doesn't support
+ * spacing over filemarks in the reverse direction. In this case, MTFSFM is also
+ * usually not supported (it is supported in the rare case in which we crossed
+ * the filemark during our read-ahead pipelined operation mode).
  *
- *     MTFSF   -       Space over mt_count filemarks in the positive direction.
- *                     The tape is positioned after the last spaced filemark.
+ * The following commands are currently not supported:
  *
- *     MTFSFM  -       Same as MTFSF, but the tape is positioned before the
- *                     last filemark.
- *
- *     MTBSF   -       Steps background over mt_count filemarks, tape is
- *                     positioned before the last filemark.
- *
- *     MTBSFM  -       Like MTBSF, only tape is positioned after the last filemark.
- *
- *     Note:
- *
- *             MTBSF and MTBSFM are not supported when the tape doesn't
- *             support spacing over filemarks in the reverse direction.
- *             In this case, MTFSFM is also usually not supported (it is
- *             supported in the rare case in which we crossed the filemark
- *             during our read-ahead pipelined operation mode).
- *             
- *     MTWEOF  -       Writes mt_count filemarks. Tape is positioned after
- *                     the last written filemark.
- *
- *     MTREW   -       Rewinds tape.
- *
- *     MTLOAD  -       Loads the tape.
- *
- *     MTOFFL  -       Puts the tape drive "Offline": Rewinds the tape and
- *     MTUNLOAD        prevents further access until the media is replaced.
- *
- *     MTNOP   -       Flushes tape buffers.
- *
- *     MTRETEN -       Retension media. This typically consists of one end
- *                     to end pass on the media.
- *
- *     MTEOM   -       Moves to the end of recorded data.
- *
- *     MTERASE -       Erases tape.
- *
- *     MTSETBLK -      Sets the user block size to mt_count bytes. If
- *                     mt_count is 0, we will attempt to autodetect
- *                     the block size.
- *
- *     MTSEEK  -       Positions the tape in a specific block number, where
- *                     each block is assumed to contain which user_block_size
- *                     bytes.
- *
- *     MTSETPART -     Switches to another tape partition.
- *
- *     MTLOCK -        Locks the tape door.
- *
- *     MTUNLOCK -      Unlocks the tape door.
- *
- *     The following commands are currently not supported:
- *
- *     MTFSS, MTBSS, MTWSM, MTSETDENSITY,
- *     MTSETDRVBUFFER, MT_ST_BOOLEANS, MT_ST_WRITE_THRESHOLD.
+ * MTFSS, MTBSS, MTWSM, MTSETDENSITY, MTSETDRVBUFFER, MT_ST_BOOLEANS,
+ * MT_ST_WRITE_THRESHOLD.
  */
-static int idetape_mtioctop (ide_drive_t *drive,short mt_op,int mt_count)
+static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count)
 {
        idetape_tape_t *tape = drive->driver_data;
        idetape_pc_t pc;
@@ -3329,29 +3280,12 @@ static int idetape_mtioctop (ide_drive_t *drive,short mt_op,int mt_count)
 }
 
 /*
- *     Our character device ioctls.
- *
- *     General mtio.h magnetic io commands are supported here, and not in
- *     the corresponding block interface.
- *
- *     The following ioctls are supported:
- *
- *     MTIOCTOP -      Refer to idetape_mtioctop for detailed description.
- *
- *     MTIOCGET -      The mt_dsreg field in the returned mtget structure
- *                     will be set to (user block size in bytes <<
- *                     MT_ST_BLKSIZE_SHIFT) & MT_ST_BLKSIZE_MASK.
- *
- *                     The mt_blkno is set to the current user block number.
- *                     The other mtget fields are not supported.
- *
- *     MTIOCPOS -      The current tape "block position" is returned. We
- *                     assume that each block contains user_block_size
- *                     bytes.
- *
- *     Our own ide-tape ioctls are supported on both interfaces.
+ * Our character device ioctls. General mtio.h magnetic io commands are
+ * supported here, and not in the corresponding block interface. Our own
+ * ide-tape ioctls are supported on both interfaces.
  */
-static int idetape_chrdev_ioctl (struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+static int idetape_chrdev_ioctl(struct inode *inode, struct file *file,
+                               unsigned int cmd, unsigned long arg)
 {
        struct ide_tape_obj *tape = ide_tape_f(file);
        ide_drive_t *drive = tape->drive;