mtd: nand: qcom: fix read failure without complete bootchain
authorAbhishek Sahu <absahu@codeaurora.org>
Fri, 11 Aug 2017 11:39:16 +0000 (17:09 +0530)
committerBoris Brezillon <boris.brezillon@free-electrons.com>
Wed, 23 Aug 2017 14:49:24 +0000 (16:49 +0200)
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is

    0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID

The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.

Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
drivers/mtd/nand/qcom_nandc.c

index 0e727d79f2ce13868d9907161bf3f7531e29d0bb..e5cb8f12d5bb50fe4d608a6fc36ea0b38ed54deb 100644 (file)
 #define        READ_ADDR                       0
 
 /* NAND_DEV_CMD_VLD bits */
-#define        READ_START_VLD                  0
+#define        READ_START_VLD                  BIT(0)
+#define        READ_STOP_VLD                   BIT(1)
+#define        WRITE_START_VLD                 BIT(2)
+#define        ERASE_START_VLD                 BIT(3)
+#define        SEQ_READ_START_VLD              BIT(4)
 
 /* NAND_EBI2_ECC_BUF_CFG bits */
 #define        NUM_STEPS                       0
 #define        FETCH_ID                        0xb
 #define        RESET_DEVICE                    0xd
 
+/* Default Value for NAND_DEV_CMD_VLD */
+#define NAND_DEV_CMD_VLD_VAL           (READ_START_VLD | WRITE_START_VLD | \
+                                        ERASE_START_VLD | SEQ_READ_START_VLD)
+
 /*
  * the NAND controller performs reads/writes with ECC in 516 byte chunks.
  * the driver calls the chunks 'step' or 'codeword' interchangeably
@@ -695,8 +703,7 @@ static int nandc_param(struct qcom_nand_host *host)
 
        /* configure CMD1 and VLD for ONFI param probing */
        nandc_set_reg(nandc, NAND_DEV_CMD_VLD,
-                     (nandc->vld & ~(1 << READ_START_VLD))
-                     | 0 << READ_START_VLD);
+                     (nandc->vld & ~READ_START_VLD));
        nandc_set_reg(nandc, NAND_DEV_CMD1,
                      (nandc->cmd1 & ~(0xFF << READ_ADDR))
                      | NAND_CMD_PARAM << READ_ADDR);
@@ -1995,13 +2002,14 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
 {
        /* kill onenand */
        nandc_write(nandc, SFLASHC_BURST_CFG, 0);
+       nandc_write(nandc, NAND_DEV_CMD_VLD, NAND_DEV_CMD_VLD_VAL);
 
        /* enable ADM DMA */
        nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN);
 
        /* save the original values of these registers */
        nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1);
-       nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD);
+       nandc->vld = NAND_DEV_CMD_VLD_VAL;
 
        return 0;
 }