help
Support for Intel's IXP4XX (XScale) family of processors.
-config ARCH_L7200
- bool "LinkUp-L7200"
- select CPU_ARM720T
- select FIQ
- select ARCH_USES_GETTIMEOFFSET
- help
- Say Y here if you intend to run this kernel on a LinkUp Systems
- L7200 Software Development Board which uses an ARM720T processor.
- Information on this board can be obtained at:
-
- <http://www.linkupsys.com/>
-
- If you have any questions or comments about the Linux kernel port
- to this board, send e-mail to <sjhill@cotw.com>.
-
config ARCH_DOVE
bool "Marvell Dove"
select PCI
config HZ
int
- default 128 if ARCH_L7200
default 200 if ARCH_EBSA110 || ARCH_S3C2410 || ARCH_S5P6440 || ARCH_S5P6442 || ARCH_S5PV210
default OMAP_32K_TIMER_HZ if ARCH_OMAP && OMAP_32K_TIMER
default AT91_TIMER_HZ if ARCH_AT91
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_KIRKWOOD) := kirkwood
machine-$(CONFIG_ARCH_KS8695) := ks8695
-machine-$(CONFIG_ARCH_L7200) := l7200
machine-$(CONFIG_ARCH_LH7A40X) := lh7a40x
machine-$(CONFIG_ARCH_LOKI) := loki
machine-$(CONFIG_ARCH_MMP) := mmp
OBJS += head-shark.o ofw-shark.o
endif
-ifeq ($(CONFIG_ARCH_L7200),y)
-OBJS += head-l7200.o
-endif
-
ifeq ($(CONFIG_ARCH_P720T),y)
# Borrow this code from SA1100
OBJS += head-sa1100.o
+++ /dev/null
-/*
- * linux/arch/arm/boot/compressed/head-l7200.S
- *
- * Copyright (C) 2000 Steve Hill <sjhill@cotw.com>
- *
- * Some code borrowed from Nicolas Pitre's 'head-sa1100.S' file. This
- * is merged with head.S by the linker.
- */
-
-#include <asm/mach-types.h>
-
-#ifndef CONFIG_ARCH_L7200
-#error What am I doing here...
-#endif
-
- .section ".start", "ax"
-
-__L7200_start:
- mov r0, #0x00100000 @ FLASH address of initrd
- mov r2, #0xf1000000 @ RAM address of initrd
- add r3, r2, #0x00700000 @ Size of initrd
-1:
- ldmia r0!, {r4, r5, r6, r7}
- stmia r2!, {r4, r5, r6, r7}
- cmp r2, r3
- ble 1b
-
- mov r8, #0 @ Zero it out
- mov r7, #MACH_TYPE_L7200 @ Set architecture ID
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Mon Mar 28 00:24:38 2005
-#
-CONFIG_ARM=y
-CONFIG_MMU=y
-CONFIG_UID16=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
-CONFIG_FIQ=y
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
-CONFIG_BROKEN_ON_SMP=y
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-# CONFIG_BSD_PROCESS_ACCT_V3 is not set
-CONFIG_SYSCTL=y
-# CONFIG_AUDIT is not set
-# CONFIG_HOTPLUG is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_EMBEDDED=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SHMEM=y
-CONFIG_CC_ALIGN_FUNCTIONS=0
-CONFIG_CC_ALIGN_LABELS=0
-CONFIG_CC_ALIGN_LOOPS=0
-CONFIG_CC_ALIGN_JUMPS=0
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-
-#
-# Loadable module support
-#
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-CONFIG_OBSOLETE_MODPARM=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
-
-#
-# System Type
-#
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_IOP3XX is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-CONFIG_ARCH_L7200=y
-# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_H720X is not set
-
-#
-# Processor Type
-#
-CONFIG_CPU_ARM720T=y
-CONFIG_CPU_32v4=y
-CONFIG_CPU_ABRT_LV4T=y
-CONFIG_CPU_CACHE_V4=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WT=y
-CONFIG_CPU_TLB_V4WT=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-
-#
-# Bus support
-#
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-# CONFIG_PREEMPT is not set
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x00010000
-CONFIG_ZBOOT_ROM_BSS=0xf03e0000
-CONFIG_ZBOOT_ROM=y
-CONFIG_CMDLINE="console=tty0 console=ttyLU1,115200 root=/dev/ram initrd=0xf1000000,0x005dac7b mem=32M"
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-# CONFIG_FPE_NWFPE is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-CONFIG_BINFMT_AOUT=y
-# CONFIG_BINFMT_MISC is not set
-# CONFIG_ARTHUR is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_SCSI is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
-#
-# Networking support
-#
-# CONFIG_NET is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
-
-#
-# Input device support
-#
-# CONFIG_INPUT is not set
-
-#
-# Hardware I/O ports
-#
-CONFIG_SERIO=y
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_SERIO_LIBPS2 is not set
-# CONFIG_SERIO_RAW is not set
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-CONFIG_SERIAL_NONSTANDARD=y
-# CONFIG_COMPUTONE is not set
-# CONFIG_ROCKETPORT is not set
-# CONFIG_CYCLADES is not set
-# CONFIG_DIGIEPCA is not set
-# CONFIG_MOXA_INTELLIO is not set
-# CONFIG_MOXA_SMARTIO is not set
-# CONFIG_ISI is not set
-# CONFIG_SYNCLINKMP is not set
-# CONFIG_N_HDLC is not set
-# CONFIG_RISCOM8 is not set
-# CONFIG_SPECIALIX is not set
-# CONFIG_SX is not set
-# CONFIG_RIO is not set
-# CONFIG_STALDRV is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_NVRAM is not set
-# CONFIG_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# Misc devices
-#
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-
-#
-# Graphics support
-#
-# CONFIG_FB is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# USB support
-#
-CONFIG_USB_ARCH_HAS_HCD=y
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB is not set
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_JBD is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-
-#
-# XFS support
-#
-# CONFIG_XFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
-# CONFIG_DEVPTS_FS_XATTR is not set
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_DEBUG_USER=y
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-# CONFIG_CRYPTO is not set
-
-#
-# Hardware crypto devices
-#
-
-#
-# Library routines
-#
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC32 is not set
-# CONFIG_LIBCRC32C is not set
endif
lib-$(CONFIG_ARCH_RPC) += ecard.o io-acorn.o floppydma.o
-lib-$(CONFIG_ARCH_L7200) += io-acorn.o
lib-$(CONFIG_ARCH_SHARK) += io-shark.o
$(obj)/csumpartialcopy.o: $(obj)/csumpartialcopygeneric.S
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-
-# Object file lists.
-
-obj-y := core.o
-obj-m :=
-obj-n :=
-obj- :=
-
+++ /dev/null
- zreladdr-y := 0xf0008000
-
+++ /dev/null
-/*
- * linux/arch/arm/mm/mm-lusl7200.c
- *
- * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Extra MM routines for L7200 architecture
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/device.h>
-
-#include <asm/types.h>
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-#include <asm/page.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-/*
- * IRQ base register
- */
-#define IRQ_BASE (IO_BASE_2 + 0x1000)
-
-/*
- * Normal IRQ registers
- */
-#define IRQ_STATUS (*(volatile unsigned long *) (IRQ_BASE + 0x000))
-#define IRQ_RAWSTATUS (*(volatile unsigned long *) (IRQ_BASE + 0x004))
-#define IRQ_ENABLE (*(volatile unsigned long *) (IRQ_BASE + 0x008))
-#define IRQ_ENABLECLEAR (*(volatile unsigned long *) (IRQ_BASE + 0x00c))
-#define IRQ_SOFT (*(volatile unsigned long *) (IRQ_BASE + 0x010))
-#define IRQ_SOURCESEL (*(volatile unsigned long *) (IRQ_BASE + 0x018))
-
-/*
- * Fast IRQ registers
- */
-#define FIQ_STATUS (*(volatile unsigned long *) (IRQ_BASE + 0x100))
-#define FIQ_RAWSTATUS (*(volatile unsigned long *) (IRQ_BASE + 0x104))
-#define FIQ_ENABLE (*(volatile unsigned long *) (IRQ_BASE + 0x108))
-#define FIQ_ENABLECLEAR (*(volatile unsigned long *) (IRQ_BASE + 0x10c))
-#define FIQ_SOFT (*(volatile unsigned long *) (IRQ_BASE + 0x110))
-#define FIQ_SOURCESEL (*(volatile unsigned long *) (IRQ_BASE + 0x118))
-
-static void l7200_mask_irq(unsigned int irq)
-{
- IRQ_ENABLECLEAR = 1 << irq;
-}
-
-static void l7200_unmask_irq(unsigned int irq)
-{
- IRQ_ENABLE = 1 << irq;
-}
-
-static struct irq_chip l7200_irq_chip = {
- .ack = l7200_mask_irq,
- .mask = l7200_mask_irq,
- .unmask = l7200_unmask_irq
-};
-
-static void __init l7200_init_irq(void)
-{
- int irq;
-
- IRQ_ENABLECLEAR = 0xffffffff; /* clear all interrupt enables */
- FIQ_ENABLECLEAR = 0xffffffff; /* clear all fast interrupt enables */
-
- for (irq = 0; irq < NR_IRQS; irq++) {
- set_irq_chip(irq, &l7200_irq_chip);
- set_irq_flags(irq, IRQF_VALID);
- set_irq_handler(irq, handle_level_irq);
- }
-
- init_FIQ();
-}
-
-static struct map_desc l7200_io_desc[] __initdata = {
- { IO_BASE, IO_START, IO_SIZE, MT_DEVICE },
- { IO_BASE_2, IO_START_2, IO_SIZE_2, MT_DEVICE },
- { AUX_BASE, AUX_START, AUX_SIZE, MT_DEVICE },
- { FLASH1_BASE, FLASH1_START, FLASH1_SIZE, MT_DEVICE },
- { FLASH2_BASE, FLASH2_START, FLASH2_SIZE, MT_DEVICE }
-};
-
-static void __init l7200_map_io(void)
-{
- iotable_init(l7200_io_desc, ARRAY_SIZE(l7200_io_desc));
-}
-
-MACHINE_START(L7200, "LinkUp Systems L7200")
- /* Maintainer: Steve Hill / Scott McConnell */
- .phys_io = 0x80040000,
- .io_pg_offst = ((0xd0000000) >> 18) & 0xfffc,
- .map_io = l7200_map_io,
- .init_irq = l7200_init_irq,
-MACHINE_END
-
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/aux_reg.h
- *
- * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 08-02-2000 SJH Created file
- */
-#ifndef _ASM_ARCH_AUXREG_H
-#define _ASM_ARCH_AUXREG_H
-
-#include <mach/hardware.h>
-
-#define l7200aux_reg *((volatile unsigned int *) (AUX_BASE))
-
-/*
- * Auxillary register values
- */
-#define AUX_CLEAR 0x00000000
-#define AUX_DIAG_LED_ON 0x00000002
-#define AUX_RTS_UART1 0x00000004
-#define AUX_DTR_UART1 0x00000008
-#define AUX_KBD_COLUMN_12_HIGH 0x00000010
-#define AUX_KBD_COLUMN_12_OFF 0x00000020
-#define AUX_KBD_COLUMN_13_HIGH 0x00000040
-#define AUX_KBD_COLUMN_13_OFF 0x00000080
-
-#endif
+++ /dev/null
-/* arch/arm/mach-l7200/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
- .equ io_virt, IO_BASE
- .equ io_phys, IO_START
-
- .macro addruart, rx, tmp
- mrc p15, 0, \rx, c1, c0
- tst \rx, #1 @ MMU enabled?
- moveq \rx, #io_phys @ physical base address
- movne \rx, #io_virt @ virtual address
- add \rx, \rx, #0x00044000 @ UART1
-@ add \rx, \rx, #0x00045000 @ UART2
- .endm
-
- .macro senduart,rd,rx
- str \rd, [\rx, #0x0] @ UARTDR
- .endm
-
- .macro waituart,rd,rx
-1001: ldr \rd, [\rx, #0x18] @ UARTFLG
- tst \rd, #1 << 5 @ UARTFLGUTXFF - 1 when full
- bne 1001b
- .endm
-
- .macro busyuart,rd,rx
-1001: ldr \rd, [\rx, #0x18] @ UARTFLG
- tst \rd, #1 << 3 @ UARTFLGUBUSY - 1 when busy
- bne 1001b
- .endm
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for L7200-based platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <mach/hardware.h>
-
- .equ irq_base_addr, IO_BASE_2
-
- .macro disable_fiq
- .endm
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro arch_ret_to_user, tmp1, tmp2
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- mov \irqstat, #irq_base_addr @ Virt addr IRQ regs
- add \irqstat, \irqstat, #0x00001000 @ Status reg
- ldr \irqstat, [\irqstat, #0] @ get interrupts
- mov \irqnr, #0
-1001: tst \irqstat, #1
- addeq \irqnr, \irqnr, #1
- moveq \irqstat, \irqstat, lsr #1
- tsteq \irqnr, #32
- beq 1001b
- teq \irqnr, #32
- .endm
-
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/gp_timers.h
- *
- * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 07-28-2000 SJH Created file
- * 08-02-2000 SJH Used structure for registers
- */
-#ifndef _ASM_ARCH_GPTIMERS_H
-#define _ASM_ARCH_GPTIMERS_H
-
-#include <mach/hardware.h>
-
-/*
- * Layout of L7200 general purpose timer registers
- */
-struct GPT_Regs {
- unsigned int TIMERLOAD;
- unsigned int TIMERVALUE;
- unsigned int TIMERCONTROL;
- unsigned int TIMERCLEAR;
-};
-
-#define GPT_BASE (IO_BASE_2 + 0x3000)
-#define l7200_timer1_regs ((volatile struct GPT_Regs *) (GPT_BASE))
-#define l7200_timer2_regs ((volatile struct GPT_Regs *) (GPT_BASE + 0x20))
-
-/*
- * General register values
- */
-#define GPT_PRESCALE_1 0x00000000
-#define GPT_PRESCALE_16 0x00000004
-#define GPT_PRESCALE_256 0x00000008
-#define GPT_MODE_FREERUN 0x00000000
-#define GPT_MODE_PERIODIC 0x00000040
-#define GPT_ENABLE 0x00000080
-#define GPT_BZTOG 0x00000100
-#define GPT_BZMOD 0x00000200
-#define GPT_LOAD_MASK 0x0000ffff
-
-#endif
+++ /dev/null
-/****************************************************************************/
-/*
- * arch/arm/mach-l7200/include/mach/gpio.h
- *
- * Registers and helper functions for the L7200 Link-Up Systems
- * GPIO.
- *
- * (C) Copyright 2000, S A McConnell (samcconn@cotw.com)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-/****************************************************************************/
-
-#define GPIO_OFF 0x00005000 /* Offset from IO_START to the GPIO reg's. */
-
-/* IO_START and IO_BASE are defined in hardware.h */
-
-#define GPIO_START (IO_START_2 + GPIO_OFF) /* Physical addr of the GPIO reg. */
-#define GPIO_BASE (IO_BASE_2 + GPIO_OFF) /* Virtual addr of the GPIO reg. */
-
-/* Offsets from the start of the GPIO for all the registers. */
-#define PADR_OFF 0x000
-#define PADDR_OFF 0x004
-#define PASBSR_OFF 0x008
-#define PAEENR_OFF 0x00c
-#define PAESNR_OFF 0x010
-#define PAESTR_OFF 0x014
-#define PAIMR_OFF 0x018
-#define PAINT_OFF 0x01c
-
-#define PBDR_OFF 0x020
-#define PBDDR_OFF 0x024
-#define PBSBSR_OFF 0x028
-#define PBIMR_OFF 0x038
-#define PBINT_OFF 0x03c
-
-#define PCDR_OFF 0x040
-#define PCDDR_OFF 0x044
-#define PCSBSR_OFF 0x048
-#define PCIMR_OFF 0x058
-#define PCINT_OFF 0x05c
-
-#define PDDR_OFF 0x060
-#define PDDDR_OFF 0x064
-#define PDSBSR_OFF 0x068
-#define PDEENR_OFF 0x06c
-#define PDESNR_OFF 0x070
-#define PDESTR_OFF 0x074
-#define PDIMR_OFF 0x078
-#define PDINT_OFF 0x07c
-
-#define PEDR_OFF 0x080
-#define PEDDR_OFF 0x084
-#define PESBSR_OFF 0x088
-#define PEEENR_OFF 0x08c
-#define PEESNR_OFF 0x090
-#define PEESTR_OFF 0x094
-#define PEIMR_OFF 0x098
-#define PEINT_OFF 0x09c
-
-/* Define the GPIO registers for use by device drivers and the kernel. */
-#define PADR (*(volatile unsigned long *)(GPIO_BASE+PADR_OFF))
-#define PADDR (*(volatile unsigned long *)(GPIO_BASE+PADDR_OFF))
-#define PASBSR (*(volatile unsigned long *)(GPIO_BASE+PASBSR_OFF))
-#define PAEENR (*(volatile unsigned long *)(GPIO_BASE+PAEENR_OFF))
-#define PAESNR (*(volatile unsigned long *)(GPIO_BASE+PAESNR_OFF))
-#define PAESTR (*(volatile unsigned long *)(GPIO_BASE+PAESTR_OFF))
-#define PAIMR (*(volatile unsigned long *)(GPIO_BASE+PAIMR_OFF))
-#define PAINT (*(volatile unsigned long *)(GPIO_BASE+PAINT_OFF))
-
-#define PBDR (*(volatile unsigned long *)(GPIO_BASE+PBDR_OFF))
-#define PBDDR (*(volatile unsigned long *)(GPIO_BASE+PBDDR_OFF))
-#define PBSBSR (*(volatile unsigned long *)(GPIO_BASE+PBSBSR_OFF))
-#define PBIMR (*(volatile unsigned long *)(GPIO_BASE+PBIMR_OFF))
-#define PBINT (*(volatile unsigned long *)(GPIO_BASE+PBINT_OFF))
-
-#define PCDR (*(volatile unsigned long *)(GPIO_BASE+PCDR_OFF))
-#define PCDDR (*(volatile unsigned long *)(GPIO_BASE+PCDDR_OFF))
-#define PCSBSR (*(volatile unsigned long *)(GPIO_BASE+PCSBSR_OFF))
-#define PCIMR (*(volatile unsigned long *)(GPIO_BASE+PCIMR_OFF))
-#define PCINT (*(volatile unsigned long *)(GPIO_BASE+PCINT_OFF))
-
-#define PDDR (*(volatile unsigned long *)(GPIO_BASE+PDDR_OFF))
-#define PDDDR (*(volatile unsigned long *)(GPIO_BASE+PDDDR_OFF))
-#define PDSBSR (*(volatile unsigned long *)(GPIO_BASE+PDSBSR_OFF))
-#define PDEENR (*(volatile unsigned long *)(GPIO_BASE+PDEENR_OFF))
-#define PDESNR (*(volatile unsigned long *)(GPIO_BASE+PDESNR_OFF))
-#define PDESTR (*(volatile unsigned long *)(GPIO_BASE+PDESTR_OFF))
-#define PDIMR (*(volatile unsigned long *)(GPIO_BASE+PDIMR_OFF))
-#define PDINT (*(volatile unsigned long *)(GPIO_BASE+PDINT_OFF))
-
-#define PEDR (*(volatile unsigned long *)(GPIO_BASE+PEDR_OFF))
-#define PEDDR (*(volatile unsigned long *)(GPIO_BASE+PEDDR_OFF))
-#define PESBSR (*(volatile unsigned long *)(GPIO_BASE+PESBSR_OFF))
-#define PEEENR (*(volatile unsigned long *)(GPIO_BASE+PEEENR_OFF))
-#define PEESNR (*(volatile unsigned long *)(GPIO_BASE+PEESNR_OFF))
-#define PEESTR (*(volatile unsigned long *)(GPIO_BASE+PEESTR_OFF))
-#define PEIMR (*(volatile unsigned long *)(GPIO_BASE+PEIMR_OFF))
-#define PEINT (*(volatile unsigned long *)(GPIO_BASE+PEINT_OFF))
-
-#define VEE_EN 0x02
-#define BACKLIGHT_EN 0x04
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/hardware.h
- *
- * Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
- * Steve Hill (sjhill@cotw.com)
- *
- * This file contains the hardware definitions for the
- * LinkUp Systems L7200 SOC development board.
- *
- * Changelog:
- * 02-01-2000 RS Created L7200 version, derived from rpc code
- * 03-21-2000 SJH Cleaned up file
- * 04-21-2000 RS Changed mapping of I/O in virtual space
- * 04-25-2000 SJH Removed unused symbols and such
- * 05-05-2000 SJH Complete rewrite
- * 07-31-2000 SJH Added undocumented debug auxillary port to
- * get at last two columns for keyboard driver
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-/* Hardware addresses of major areas.
- * *_START is the physical address
- * *_SIZE is the size of the region
- * *_BASE is the virtual address
- */
-#define RAM_START 0xf0000000
-#define RAM_SIZE 0x02000000
-#define RAM_BASE 0xc0000000
-
-#define IO_START 0x80000000 /* I/O */
-#define IO_SIZE 0x01000000
-#define IO_BASE 0xd0000000
-
-#define IO_START_2 0x90000000 /* I/O */
-#define IO_SIZE_2 0x01000000
-#define IO_BASE_2 0xd1000000
-
-#define AUX_START 0x1a000000 /* AUX PORT */
-#define AUX_SIZE 0x01000000
-#define AUX_BASE 0xd2000000
-
-#define FLASH1_START 0x00000000 /* FLASH BANK 1 */
-#define FLASH1_SIZE 0x01000000
-#define FLASH1_BASE 0xd3000000
-
-#define FLASH2_START 0x10000000 /* FLASH BANK 2 */
-#define FLASH2_SIZE 0x01000000
-#define FLASH2_BASE 0xd4000000
-
-#define ISA_START 0x20000000 /* ISA */
-#define ISA_SIZE 0x20000000
-#define ISA_BASE 0xe0000000
-
-#define PCIO_BASE IO_BASE
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/io.h
- *
- * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 03-21-2000 SJH Created from arch/arm/mach-nexuspci/include/mach/io.h
- * 08-31-2000 SJH Added in IO functions necessary for new drivers
- */
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * There are not real ISA nor PCI buses, so we fake it.
- */
-#define __io(a) __typesafe_io(a)
-#define __mem_pci(a) (a)
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/irqs.h
- *
- * Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
- * Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 01-02-2000 RS Create l7200 version
- * 03-28-2000 SJH Removed unused interrupt
- * 07-28-2000 SJH Added pseudo-keyboard interrupt
- */
-
-/*
- * NOTE: The second timer (Timer 2) is used as the keyboard
- * interrupt when the keyboard driver is enabled.
- */
-
-#define NR_IRQS 32
-
-#define IRQ_STWDOG 0 /* Watchdog timer */
-#define IRQ_PROG 1 /* Programmable interrupt */
-#define IRQ_DEBUG_RX 2 /* Comm Rx debug */
-#define IRQ_DEBUG_TX 3 /* Comm Tx debug */
-#define IRQ_GCTC1 4 /* Timer 1 */
-#define IRQ_GCTC2 5 /* Timer 2 / Keyboard */
-#define IRQ_DMA 6 /* DMA controller */
-#define IRQ_CLCD 7 /* Color LCD controller */
-#define IRQ_SM_RX 8 /* Smart card */
-#define IRQ_SM_TX 9 /* Smart cart */
-#define IRQ_SM_RST 10 /* Smart card */
-#define IRQ_SIB 11 /* Serial Interface Bus */
-#define IRQ_MMC 12 /* MultiMediaCard */
-#define IRQ_SSP1 13 /* Synchronous Serial Port 1 */
-#define IRQ_SSP2 14 /* Synchronous Serial Port 1 */
-#define IRQ_SPI 15 /* SPI slave */
-#define IRQ_UART_1 16 /* UART 1 */
-#define IRQ_UART_2 17 /* UART 2 */
-#define IRQ_IRDA 18 /* IRDA */
-#define IRQ_RTC_TICK 19 /* Real Time Clock tick */
-#define IRQ_RTC_ALARM 20 /* Real Time Clock alarm */
-#define IRQ_GPIO 21 /* General Purpose IO */
-#define IRQ_GPIO_DMA 22 /* General Purpose IO, DMA */
-#define IRQ_M2M 23 /* Memory to memory DMA */
-#define IRQ_RESERVED 24 /* RESERVED, don't use */
-#define IRQ_INTF 25 /* External active low interrupt */
-#define IRQ_INT0 26 /* External active low interrupt */
-#define IRQ_INT1 27 /* External active low interrupt */
-#define IRQ_INT2 28 /* External active low interrupt */
-#define IRQ_UCB1200 29 /* Interrupt generated by UCB1200*/
-#define IRQ_BAT_LO 30 /* Low batery or external power */
-#define IRQ_MEDIA_CHG 31 /* Media change interrupt */
-
-/*
- * This is the offset of the FIQ "IRQ" numbers
- */
-#define FIQ_START 64
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/memory.h
- *
- * Copyright (c) 2000 Steve Hill (sjhill@cotw.com)
- * Copyright (c) 2000 Rob Scott (rscott@mtrob.fdns.net)
- *
- * Changelog:
- * 03-13-2000 SJH Created
- * 04-13-2000 RS Changed bus macros for new addr
- * 05-03-2000 SJH Removed bus macros and fixed virt_to_phys macro
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset on the L7200 SDB.
- */
-#define PHYS_OFFSET UL(0xf0000000)
-
-/*
- * Cache flushing area - ROM
- */
-#define FLUSH_BASE_PHYS 0x40000000
-#define FLUSH_BASE 0xdf000000
-
-#endif
+++ /dev/null
-/****************************************************************************/
-/*
- * arch/arm/mach-l7200/include/mach/pmpcon.h
- *
- * Registers and helper functions for the L7200 Link-Up Systems
- * DC/DC converter register.
- *
- * (C) Copyright 2000, S A McConnell (samcconn@cotw.com)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-/****************************************************************************/
-
-#define PMPCON_OFF 0x00006000 /* Offset from IO_START_2. */
-
-/* IO_START_2 and IO_BASE_2 are defined in hardware.h */
-
-#define PMPCON_START (IO_START_2 + PMPCON_OFF) /* Physical address of reg. */
-#define PMPCON_BASE (IO_BASE_2 + PMPCON_OFF) /* Virtual address of reg. */
-
-
-#define PMPCON (*(volatile unsigned int *)(PMPCON_BASE))
-
-#define PWM2_50CYCLE 0x800
-#define CONTRAST 0x9
-
-#define PWM1H (CONTRAST)
-#define PWM1L (CONTRAST << 4)
-
-#define PMPCON_VALUE (PWM2_50CYCLE | PWM1L | PWM1H)
-
-/* PMPCON = 0x811; // too light and fuzzy
- * PMPCON = 0x844;
- * PMPCON = 0x866; // better color poor depth
- * PMPCON = 0x888; // Darker but better depth
- * PMPCON = 0x899; // Darker even better depth
- * PMPCON = 0x8aa; // too dark even better depth
- * PMPCON = 0X8cc; // Way too dark
- */
-
-/* As CONTRAST value increases the greater the depth perception and
- * the darker the colors.
- */
+++ /dev/null
-/****************************************************************************/
-/*
- * arch/arm/mach-l7200/include/mach/pmu.h
- *
- * Registers and helper functions for the L7200 Link-Up Systems
- * Power Management Unit (PMU).
- *
- * (C) Copyright 2000, S A McConnell (samcconn@cotw.com)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-/****************************************************************************/
-
-#define PMU_OFF 0x00050000 /* Offset from IO_START to the PMU registers. */
-
-/* IO_START and IO_BASE are defined in hardware.h */
-
-#define PMU_START (IO_START + PMU_OFF) /* Physical addr. of the PMU reg. */
-#define PMU_BASE (IO_BASE + PMU_OFF) /* Virtual addr. of the PMU reg. */
-
-
-/* Define the PMU registers for use by device drivers and the kernel. */
-
-typedef struct {
- unsigned int CURRENT; /* Current configuration register */
- unsigned int NEXT; /* Next configuration register */
- unsigned int reserved;
- unsigned int RUN; /* Run configuration register */
- unsigned int COMM; /* Configuration command register */
- unsigned int SDRAM; /* SDRAM configuration bypass register */
-} pmu_interface;
-
-#define PMU ((volatile pmu_interface *)(PMU_BASE))
-
-
-/* Macro's for reading the common register fields. */
-
-#define GET_TRANSOP(reg) ((reg >> 25) & 0x03) /* Bits 26-25 */
-#define GET_OSCEN(reg) ((reg >> 16) & 0x01)
-#define GET_OSCMUX(reg) ((reg >> 15) & 0x01)
-#define GET_PLLMUL(reg) ((reg >> 9) & 0x3f) /* Bits 14-9 */
-#define GET_PLLEN(reg) ((reg >> 8) & 0x01)
-#define GET_PLLMUX(reg) ((reg >> 7) & 0x01)
-#define GET_BCLK_DIV(reg) ((reg >> 3) & 0x03) /* Bits 4-3 */
-#define GET_SDRB_SEL(reg) ((reg >> 2) & 0x01)
-#define GET_SDRF_SEL(reg) ((reg >> 1) & 0x01)
-#define GET_FASTBUS(reg) (reg & 0x1)
-
-/* CFG_NEXT register */
-
-#define CFG_NEXT_CLOCKRECOVERY ((PMU->NEXT >> 18) & 0x7f) /* Bits 24-18 */
-#define CFG_NEXT_INTRET ((PMU->NEXT >> 17) & 0x01)
-#define CFG_NEXT_SDR_STOP ((PMU->NEXT >> 6) & 0x01)
-#define CFG_NEXT_SYSCLKEN ((PMU->NEXT >> 5) & 0x01)
-
-/* Useful field values that can be used to construct the
- * CFG_NEXT and CFG_RUN registers.
- */
-
-#define TRANSOP_NOP 0<<25 /* NOCHANGE_NOSTALL */
-#define NOCHANGE_STALL 1<<25
-#define CHANGE_NOSTALL 2<<25
-#define CHANGE_STALL 3<<25
-
-#define INTRET 1<<17
-#define OSCEN 1<<16
-#define OSCMUX 1<<15
-
-/* PLL frequencies */
-
-#define PLLMUL_0 0<<9 /* 3.6864 MHz */
-#define PLLMUL_1 1<<9 /* ?????? MHz */
-#define PLLMUL_5 5<<9 /* 18.432 MHz */
-#define PLLMUL_10 10<<9 /* 36.864 MHz */
-#define PLLMUL_18 18<<9 /* ?????? MHz */
-#define PLLMUL_20 20<<9 /* 73.728 MHz */
-#define PLLMUL_32 32<<9 /* ?????? MHz */
-#define PLLMUL_35 35<<9 /* 129.024 MHz */
-#define PLLMUL_36 36<<9 /* ?????? MHz */
-#define PLLMUL_39 39<<9 /* ?????? MHz */
-#define PLLMUL_40 40<<9 /* 147.456 MHz */
-
-/* Clock recovery times */
-
-#define CRCLOCK_1 1<<18
-#define CRCLOCK_2 2<<18
-#define CRCLOCK_4 4<<18
-#define CRCLOCK_8 8<<18
-#define CRCLOCK_16 16<<18
-#define CRCLOCK_32 32<<18
-#define CRCLOCK_63 63<<18
-#define CRCLOCK_127 127<<18
-
-#define PLLEN 1<<8
-#define PLLMUX 1<<7
-#define SDR_STOP 1<<6
-#define SYSCLKEN 1<<5
-
-#define BCLK_DIV_4 2<<3
-#define BCLK_DIV_2 1<<3
-#define BCLK_DIV_1 0<<3
-
-#define SDRB_SEL 1<<2
-#define SDRF_SEL 1<<1
-#define FASTBUS 1<<0
-
-
-/* CFG_SDRAM */
-
-#define SDRREFFQ 1<<0 /* Only if SDRSTOPRQ is not set. */
-#define SDRREFACK 1<<1 /* Read-only */
-#define SDRSTOPRQ 1<<2 /* Only if SDRREFFQ is not set. */
-#define SDRSTOPACK 1<<3 /* Read-only */
-#define PICEN 1<<4 /* Enable Co-procesor */
-#define PICTEST 1<<5
-
-#define GET_SDRREFFQ ((PMU->SDRAM >> 0) & 0x01)
-#define GET_SDRREFACK ((PMU->SDRAM >> 1) & 0x01) /* Read-only */
-#define GET_SDRSTOPRQ ((PMU->SDRAM >> 2) & 0x01)
-#define GET_SDRSTOPACK ((PMU->SDRAM >> 3) & 0x01) /* Read-only */
-#define GET_PICEN ((PMU->SDRAM >> 4) & 0x01)
-#define GET_PICTEST ((PMU->SDRAM >> 5) & 0x01)
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/serial.h
- *
- * Copyright (c) 2000 Rob Scott (rscott@mtrob.fdns.net)
- * Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 03-20-2000 SJH Created
- * 03-26-2000 SJH Added flags for serial ports
- * 03-27-2000 SJH Corrected BASE_BAUD value
- * 04-14-2000 RS Made register addr dependent on IO_BASE
- * 05-03-2000 SJH Complete rewrite
- * 05-09-2000 SJH Stripped out architecture specific serial stuff
- * and placed it in a separate file
- * 07-28-2000 SJH Moved base baud rate variable
- */
-#ifndef __ASM_ARCH_SERIAL_H
-#define __ASM_ARCH_SERIAL_H
-
-/*
- * This assumes you have a 3.6864 MHz clock for your UART.
- */
-#define BASE_BAUD 3686400
-
-/*
- * Standard COM flags
- */
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-
-#define STD_SERIAL_PORT_DEFNS \
- /* MAGIC UART CLK PORT IRQ FLAGS */ \
- { 0, BASE_BAUD, UART1_BASE, IRQ_UART_1, STD_COM_FLAGS }, /* ttyLU0 */ \
- { 0, BASE_BAUD, UART2_BASE, IRQ_UART_2, STD_COM_FLAGS }, /* ttyLU1 */ \
-
-#define EXTRA_SERIAL_PORT_DEFNS
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/serial_l7200.h
- *
- * Copyright (c) 2000 Steven Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 05-09-2000 SJH Created
- */
-#ifndef __ASM_ARCH_SERIAL_L7200_H
-#define __ASM_ARCH_SERIAL_L7200_H
-
-#include <mach/memory.h>
-
-/*
- * This assumes you have a 3.6864 MHz clock for your UART.
- */
-#define BASE_BAUD 3686400
-
-/*
- * UART base register addresses
- */
-#define UART1_BASE (IO_BASE + 0x00044000)
-#define UART2_BASE (IO_BASE + 0x00045000)
-
-/*
- * UART register offsets
- */
-#define UARTDR 0x00 /* Tx/Rx data */
-#define RXSTAT 0x04 /* Rx status */
-#define H_UBRLCR 0x08 /* mode register high */
-#define M_UBRLCR 0x0C /* mode reg mid (MSB of baud)*/
-#define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/
-#define UARTCON 0x14 /* control register */
-#define UARTFLG 0x18 /* flag register */
-#define UARTINTSTAT 0x1C /* FIFO IRQ status register */
-#define UARTINTMASK 0x20 /* FIFO IRQ mask register */
-
-/*
- * UART baud rate register values
- */
-#define BR_110 0x827
-#define BR_1200 0x06e
-#define BR_2400 0x05f
-#define BR_4800 0x02f
-#define BR_9600 0x017
-#define BR_14400 0x00f
-#define BR_19200 0x00b
-#define BR_38400 0x005
-#define BR_57600 0x003
-#define BR_76800 0x002
-#define BR_115200 0x001
-
-/*
- * Receiver status register (RXSTAT) mask values
- */
-#define RXSTAT_NO_ERR 0x00 /* No error */
-#define RXSTAT_FRM_ERR 0x01 /* Framing error */
-#define RXSTAT_PAR_ERR 0x02 /* Parity error */
-#define RXSTAT_OVR_ERR 0x04 /* Overrun error */
-
-/*
- * High byte of UART bit rate and line control register (H_UBRLCR) values
- */
-#define UBRLCR_BRK 0x01 /* generate break on tx */
-#define UBRLCR_PEN 0x02 /* enable parity */
-#define UBRLCR_PDIS 0x00 /* disable parity */
-#define UBRLCR_EVEN 0x04 /* 1= even parity,0 = odd parity */
-#define UBRLCR_STP2 0x08 /* transmit 2 stop bits */
-#define UBRLCR_FIFO 0x10 /* enable FIFO */
-#define UBRLCR_LEN5 0x60 /* word length5 */
-#define UBRLCR_LEN6 0x40 /* word length6 */
-#define UBRLCR_LEN7 0x20 /* word length7 */
-#define UBRLCR_LEN8 0x00 /* word length8 */
-
-/*
- * UART control register (UARTCON) values
- */
-#define UARTCON_UARTEN 0x01 /* Enable UART */
-#define UARTCON_DMAONERR 0x08 /* Mask RxDmaRq when errors occur */
-
-/*
- * UART flag register (UARTFLG) mask values
- */
-#define UARTFLG_UTXFF 0x20 /* Transmit FIFO full */
-#define UARTFLG_URXFE 0x10 /* Receiver FIFO empty */
-#define UARTFLG_UBUSY 0x08 /* Transmitter busy */
-#define UARTFLG_DCD 0x04 /* Data carrier detect */
-#define UARTFLG_DSR 0x02 /* Data set ready */
-#define UARTFLG_CTS 0x01 /* Clear to send */
-
-/*
- * UART interrupt status/clear registers (UARTINTSTAT/CLR) values
- */
-#define UART_TXINT 0x01 /* TX interrupt */
-#define UART_RXINT 0x02 /* RX interrupt */
-#define UART_RXERRINT 0x04 /* RX error interrupt */
-#define UART_MSINT 0x08 /* Modem Status interrupt */
-#define UART_UDINT 0x10 /* UART Disabled interrupt */
-#define UART_ALLIRQS 0x1f /* All interrupts */
-
-#endif
+++ /dev/null
-/****************************************************************************/
-/*
- * arch/arm/mach-l7200/include/mach/sib.h
- *
- * Registers and helper functions for the Serial Interface Bus.
- *
- * (C) Copyright 2000, S A McConnell (samcconn@cotw.com)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-/****************************************************************************/
-
-#define SIB_OFF 0x00040000 /* Offset from IO_START to the SIB reg's. */
-
-/* IO_START and IO_BASE are defined in hardware.h */
-
-#define SIB_START (IO_START + SIB_OFF) /* Physical addr of the SIB reg. */
-#define SIB_BASE (IO_BASE + SIB_OFF) /* Virtual addr of the SIB reg. */
-
-/* Offsets from the start of the SIB for all the registers. */
-
-/* Define the SIB registers for use by device drivers and the kernel. */
-
-typedef struct
-{
- unsigned int MCCR; /* SIB Control Register Offset: 0x00 */
- unsigned int RES1; /* Reserved Offset: 0x04 */
- unsigned int MCDR0; /* SIB Data Register 0 Offset: 0x08 */
- unsigned int MCDR1; /* SIB Data Register 1 Offset: 0x0c */
- unsigned int MCDR2; /* SIB Data Register 2 (UCB1x00) Offset: 0x10 */
- unsigned int RES2; /* Reserved Offset: 0x14 */
- unsigned int MCSR; /* SIB Status Register Offset: 0x18 */
-} SIB_Interface;
-
-#define SIB ((volatile SIB_Interface *) (SIB_BASE))
-
-/* MCCR */
-
-#define INTERNAL_FREQ 9216000 /* Hertz */
-#define AUDIO_FREQ 5000 /* Hertz */
-#define TELECOM_FREQ 5000 /* Hertz */
-
-#define AUDIO_DIVIDE (INTERNAL_FREQ / (32 * AUDIO_FREQ))
-#define TELECOM_DIVIDE (INTERNAL_FREQ / (32 * TELECOM_FREQ))
-
-#define MCCR_ASD57 AUDIO_DIVIDE
-#define MCCR_TSD57 (TELECOM_DIVIDE << 8)
-#define MCCR_MCE (1 << 16) /* SIB enable */
-#define MCCR_ECS (1 << 17) /* External Clock Select */
-#define MCCR_ADM (1 << 18) /* A/D Data Sampling */
-#define MCCR_PMC (1 << 26) /* PIN Multiplexer Control */
-
-
-#define GET_ASD ((SIB->MCCR >> 0) & 0x3f) /* Audio Sample Rate Div. */
-#define GET_TSD ((SIB->MCCR >> 8) & 0x3f) /* Telcom Sample Rate Div. */
-#define GET_MCE ((SIB->MCCR >> 16) & 0x01) /* SIB Enable */
-#define GET_ECS ((SIB->MCCR >> 17) & 0x01) /* External Clock Select */
-#define GET_ADM ((SIB->MCCR >> 18) & 0x01) /* A/D Data Sampling Mode */
-#define GET_TTM ((SIB->MCCR >> 19) & 0x01) /* Telco Trans. FIFO I mask */
-#define GET_TRM ((SIB->MCCR >> 20) & 0x01) /* Telco Recv. FIFO I mask */
-#define GET_ATM ((SIB->MCCR >> 21) & 0x01) /* Audio Trans. FIFO I mask */
-#define GET_ARM ((SIB->MCCR >> 22) & 0x01) /* Audio Recv. FIFO I mask */
-#define GET_LBM ((SIB->MCCR >> 23) & 0x01) /* Loop Back Mode */
-#define GET_ECP ((SIB->MCCR >> 24) & 0x03) /* Extern. Clck Prescale sel */
-#define GET_PMC ((SIB->MCCR >> 26) & 0x01) /* PIN Multiplexer Control */
-#define GET_ERI ((SIB->MCCR >> 27) & 0x01) /* External Read Interrupt */
-#define GET_EWI ((SIB->MCCR >> 28) & 0x01) /* External Write Interrupt */
-
-/* MCDR0 */
-
-#define AUDIO_RECV ((SIB->MCDR0 >> 4) & 0xfff)
-#define AUDIO_WRITE(v) ((SIB->MCDR0 = (v & 0xfff) << 4))
-
-/* MCDR1 */
-
-#define TELECOM_RECV ((SIB->MCDR1 >> 2) & 032fff)
-#define TELECOM_WRITE(v) ((SIB->MCDR1 = (v & 0x3fff) << 2))
-
-
-/* MCSR */
-
-#define MCSR_ATU (1 << 4) /* Audio Transmit FIFO Underrun */
-#define MCSR_ARO (1 << 5) /* Audio Receive FIFO Underrun */
-#define MCSR_TTU (1 << 6) /* TELECOM Transmit FIFO Underrun */
-#define MCSR_TRO (1 << 7) /* TELECOM Receive FIFO Underrun */
-
-#define MCSR_CLEAR_UNDERUN_BITS (MCSR_ATU | MCSR_ARO | MCSR_TTU | MCSR_TRO)
-
-
-#define GET_ATS ((SIB->MCSR >> 0) & 0x01) /* Audio Transmit FIFO Service Req*/
-#define GET_ARS ((SIB->MCSR >> 1) & 0x01) /* Audio Recv FIFO Service Request*/
-#define GET_TTS ((SIB->MCSR >> 2) & 0x01) /* TELECOM Transmit FIFO Flag */
-#define GET_TRS ((SIB->MCSR >> 3) & 0x01) /* TELECOM Recv FIFO Service Req. */
-#define GET_ATU ((SIB->MCSR >> 4) & 0x01) /* Audio Transmit FIFO Underrun */
-#define GET_ARO ((SIB->MCSR >> 5) & 0x01) /* Audio Receive FIFO Underrun */
-#define GET_TTU ((SIB->MCSR >> 6) & 0x01) /* TELECOM Transmit FIFO Underrun */
-#define GET_TRO ((SIB->MCSR >> 7) & 0x01) /* TELECOM Receive FIFO Underrun */
-#define GET_ANF ((SIB->MCSR >> 8) & 0x01) /* Audio Transmit FIFO not full */
-#define GET_ANE ((SIB->MCSR >> 9) & 0x01) /* Audio Receive FIFO not empty */
-#define GET_TNF ((SIB->MCSR >> 10) & 0x01) /* Telecom Transmit FIFO not full */
-#define GET_TNE ((SIB->MCSR >> 11) & 0x01) /* Telecom Receive FIFO not empty */
-#define GET_CWC ((SIB->MCSR >> 12) & 0x01) /* Codec Write Complete */
-#define GET_CRC ((SIB->MCSR >> 13) & 0x01) /* Codec Read Complete */
-#define GET_ACE ((SIB->MCSR >> 14) & 0x01) /* Audio Codec Enabled */
-#define GET_TCE ((SIB->MCSR >> 15) & 0x01) /* Telecom Codec Enabled */
-
-/* MCDR2 */
-
-#define MCDR2_rW (1 << 16)
-
-#define WRITE_MCDR2(reg, data) (SIB->MCDR2 =((reg<<17)|MCDR2_rW|(data&0xffff)))
-#define MCDR2_WRITE_COMPLETE GET_CWC
-
-#define INITIATE_MCDR2_READ(reg) (SIB->MCDR2 = (reg << 17))
-#define MCDR2_READ_COMPLETE GET_CRC
-#define MCDR2_READ (SIB->MCDR2 & 0xffff)
+++ /dev/null
-/****************************************************************************/
-/*
- * arch/arm/mach-l7200/include/mach/sys-clock.h
- *
- * Registers and helper functions for the L7200 Link-Up Systems
- * System clocks.
- *
- * (C) Copyright 2000, S A McConnell (samcconn@cotw.com)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-/****************************************************************************/
-
-#define SYS_CLOCK_OFF 0x00050030 /* Offset from IO_START. */
-
-/* IO_START and IO_BASE are defined in hardware.h */
-
-#define SYS_CLOCK_START (IO_START + SYS_CLOCK_OFF) /* Physical address */
-#define SYS_CLOCK_BASE (IO_BASE + SYS_CLOCK_OFF) /* Virtual address */
-
-/* Define the interface to the SYS_CLOCK */
-
-typedef struct
-{
- unsigned int ENABLE;
- unsigned int ESYNC;
- unsigned int SELECT;
-} sys_clock_interface;
-
-#define SYS_CLOCK ((volatile sys_clock_interface *)(SYS_CLOCK_BASE))
-
-//#define CLOCK_EN (*(volatile unsigned long *)(PMU_BASE+CLOCK_EN_OFF))
-//#define CLOCK_ESYNC (*(volatile unsigned long *)(PMU_BASE+CLOCK_ESYNC_OFF))
-//#define CLOCK_SEL (*(volatile unsigned long *)(PMU_BASE+CLOCK_SEL_OFF))
-
-/* SYS_CLOCK -> ENABLE */
-
-#define SYN_EN 1<<0
-#define B18M_EN 1<<1
-#define CLK3M6_EN 1<<2
-#define BUART_EN 1<<3
-#define CLK18MU_EN 1<<4
-#define FIR_EN 1<<5
-#define MIRN_EN 1<<6
-#define UARTM_EN 1<<7
-#define SIBADC_EN 1<<8
-#define ALTD_EN 1<<9
-#define CLCLK_EN 1<<10
-
-/* SYS_CLOCK -> SELECT */
-
-#define CLK18M_DIV 1<<0
-#define MIR_SEL 1<<1
-#define SSP_SEL 1<<4
-#define MM_DIV 1<<5
-#define MM_SEL 1<<6
-#define ADC_SEL_2 0<<7
-#define ADC_SEL_4 1<<7
-#define ADC_SEL_8 3<<7
-#define ADC_SEL_16 7<<7
-#define ADC_SEL_32 0x0f<<7
-#define ADC_SEL_64 0x1f<<7
-#define ADC_SEL_128 0x3f<<7
-#define ALTD_SEL 1<<13
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/system.h
- *
- * Copyright (c) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Changelog
- * 03-21-2000 SJH Created
- * 04-26-2000 SJH Fixed functions
- * 05-03-2000 SJH Removed usage of obsolete 'iomd.h'
- * 05-31-2000 SJH Properly implemented 'arch_idle'
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/hardware.h>
-
-static inline void arch_idle(void)
-{
- *(unsigned long *)(IO_BASE + 0x50004) = 1; /* idle mode */
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
- if (mode == 's') {
- cpu_reset(0);
- }
-}
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/time.h
- *
- * Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
- * Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 01-02-2000 RS Created l7200 version, derived from rpc code
- * 05-03-2000 SJH Complete rewrite
- */
-#ifndef _ASM_ARCH_TIME_H
-#define _ASM_ARCH_TIME_H
-
-#include <mach/irqs.h>
-
-/*
- * RTC base register address
- */
-#define RTC_BASE (IO_BASE_2 + 0x2000)
-
-/*
- * RTC registers
- */
-#define RTC_RTCDR (*(volatile unsigned char *) (RTC_BASE + 0x000))
-#define RTC_RTCMR (*(volatile unsigned char *) (RTC_BASE + 0x004))
-#define RTC_RTCS (*(volatile unsigned char *) (RTC_BASE + 0x008))
-#define RTC_RTCC (*(volatile unsigned char *) (RTC_BASE + 0x008))
-#define RTC_RTCDV (*(volatile unsigned char *) (RTC_BASE + 0x00c))
-#define RTC_RTCCR (*(volatile unsigned char *) (RTC_BASE + 0x010))
-
-/*
- * RTCCR register values
- */
-#define RTC_RATE_32 0x00 /* 32 Hz tick */
-#define RTC_RATE_64 0x10 /* 64 Hz tick */
-#define RTC_RATE_128 0x20 /* 128 Hz tick */
-#define RTC_RATE_256 0x30 /* 256 Hz tick */
-#define RTC_EN_ALARM 0x01 /* Enable alarm */
-#define RTC_EN_TIC 0x04 /* Enable counter */
-#define RTC_EN_STWDOG 0x08 /* Enable watchdog */
-
-/*
- * Handler for RTC timer interrupt
- */
-static irqreturn_t
-timer_interrupt(int irq, void *dev_id)
-{
- struct pt_regs *regs = get_irq_regs();
- do_timer(1);
-#ifndef CONFIG_SMP
- update_process_times(user_mode(regs));
-#endif
- do_profile(regs);
- RTC_RTCC = 0; /* Clear interrupt */
-
- return IRQ_HANDLED;
-}
-
-/*
- * Set up RTC timer interrupt, and return the current time in seconds.
- */
-void __init time_init(void)
-{
- RTC_RTCC = 0; /* Clear interrupt */
-
- timer_irq.handler = timer_interrupt;
-
- setup_irq(IRQ_RTC_TICK, &timer_irq);
-
- RTC_RTCCR = RTC_RATE_128 | RTC_EN_TIC; /* Set rate and enable timer */
-}
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/timex.h
- *
- * Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
- * Steve Hill (sjhill@cotw.com)
- *
- * 04-21-2000 RS Created file
- * 05-03-2000 SJH Tick rate was wrong
- *
- */
-
-/*
- * On the ARM720T, clock ticks are set to 128 Hz.
- *
- * NOTE: The actual RTC value is set in 'time.h' which
- * must be changed when choosing a different tick
- * rate. The value of HZ in 'param.h' must also
- * be changed to match below.
- */
-#define CLOCK_TICK_RATE 128
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/uncompress.h
- *
- * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
- *
- * Changelog:
- * 05-01-2000 SJH Created
- * 05-13-2000 SJH Filled in function bodies
- * 07-26-2000 SJH Removed hard coded baud rate
- */
-
-#include <mach/hardware.h>
-
-#define IO_UART IO_START + 0x00044000
-
-#define __raw_writeb(v,p) (*(volatile unsigned char *)(p) = (v))
-#define __raw_readb(p) (*(volatile unsigned char *)(p))
-
-static inline void putc(int c)
-{
- while(__raw_readb(IO_UART + 0x18) & 0x20 ||
- __raw_readb(IO_UART + 0x18) & 0x08)
- barrier();
-
- __raw_writeb(c, IO_UART + 0x00);
-}
-
-static inline void flush(void)
-{
-}
-
-static __inline__ void arch_decomp_setup(void)
-{
- __raw_writeb(0x00, IO_UART + 0x08); /* Set HSB */
- __raw_writeb(0x00, IO_UART + 0x20); /* Disable IRQs */
- __raw_writeb(0x01, IO_UART + 0x14); /* Enable UART */
-}
-
-#define arch_decomp_wdog()
+++ /dev/null
-/*
- * arch/arm/mach-l7200/include/mach/vmalloc.h
- */
-#define VMALLOC_END (PAGE_OFFSET + 0x10000000)
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / commitdiff