tc35815: Use generic PHY layer
authorAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Fri, 11 Apr 2008 15:47:46 +0000 (00:47 +0900)
committerJeff Garzik <jgarzik@redhat.com>
Thu, 17 Apr 2008 00:06:50 +0000 (20:06 -0400)
Convert the tc35815 driver to use the generic PHY layer in
drivers/net/phy.  Also rename 'boardtype' to 'chiptype' which hould be
more appropriate.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/Kconfig
drivers/net/tc35815.c

index da30a31e66f975352fbd1b6de4294c281b1a5e4b..45c3a208d93f081acd67743e77e304310c39ffd5 100644 (file)
@@ -1438,7 +1438,7 @@ config CS89x0
 config TC35815
        tristate "TOSHIBA TC35815 Ethernet support"
        depends on NET_PCI && PCI && MIPS
-       select MII
+       select PHYLIB
 
 config EEPRO100
        tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
index 60eff784d5e4c585dc16ecd314e1026e4934728d..59f783eb98b9c2916280121988041248f972bb1f 100644 (file)
@@ -23,9 +23,9 @@
  */
 
 #ifdef TC35815_NAPI
-#define DRV_VERSION    "1.36-NAPI"
+#define DRV_VERSION    "1.37-NAPI"
 #else
-#define DRV_VERSION    "1.36"
+#define DRV_VERSION    "1.37"
 #endif
 static const char *version = "tc35815.c:v" DRV_VERSION "\n";
 #define MODNAME                        "tc35815"
@@ -47,8 +47,8 @@ static const char *version = "tc35815.c:v" DRV_VERSION "\n";
 #include <linux/skbuff.h>
 #include <linux/delay.h>
 #include <linux/pci.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/workqueue.h>
 #include <linux/platform_device.h>
 #include <asm/io.h>
 #include <asm/byteorder.h>
@@ -60,16 +60,16 @@ static const char *version = "tc35815.c:v" DRV_VERSION "\n";
 #define WORKAROUND_100HALF_PROMISC
 /* #define TC35815_USE_PACKEDBUFFER */
 
-typedef enum {
+enum tc35815_chiptype {
        TC35815CF = 0,
        TC35815_NWU,
        TC35815_TX4939,
-} board_t;
+};
 
-/* indexed by board_t, above */
+/* indexed by tc35815_chiptype, above */
 static const struct {
        const char *name;
-} board_info[] __devinitdata = {
+} chip_info[] __devinitdata = {
        { "TOSHIBA TC35815CF 10/100BaseTX" },
        { "TOSHIBA TC35815 with Wake on LAN" },
        { "TOSHIBA TC35815/TX4939" },
@@ -87,7 +87,6 @@ MODULE_DEVICE_TABLE (pci, tc35815_pci_tbl);
 static struct tc35815_options {
        int speed;
        int duplex;
-       int doforce;
 } options;
 
 /*
@@ -348,7 +347,7 @@ struct BDesc {
        Int_STargAbtEn | \
        Int_BLExEn  | Int_FDAExEn) /* maybe 0xb7f*/
 #define DMA_CTL_CMD    DMA_BURST_SIZE
-#define HAVE_DMA_RXALIGN(lp)   likely((lp)->boardtype != TC35815CF)
+#define HAVE_DMA_RXALIGN(lp)   likely((lp)->chiptype != TC35815CF)
 
 /* Tuning parameters */
 #define DMA_BURST_SIZE 32
@@ -401,16 +400,7 @@ struct FrFD {
 
 #define TC35815_TX_TIMEOUT  msecs_to_jiffies(400)
 
-/* Timer state engine. */
-enum tc35815_timer_state {
-       arbwait  = 0,   /* Waiting for auto negotiation to complete.          */
-       lupwait  = 1,   /* Auto-neg complete, awaiting link-up status.        */
-       ltrywait = 2,   /* Forcing try of all modes, from fastest to slowest. */
-       asleep   = 3,   /* Time inactive.                                     */
-       lcheck   = 4,   /* Check link status.                                 */
-};
-
-/* Information that need to be kept for each board. */
+/* Information that need to be kept for each controller. */
 struct tc35815_local {
        struct pci_dev *pci_dev;
 
@@ -432,12 +422,12 @@ struct tc35815_local {
         */
        spinlock_t lock;
 
-       int phy_addr;
-       int fullduplex;
-       unsigned short saved_lpa;
-       struct timer_list timer;
-       enum tc35815_timer_state timer_state; /* State of auto-neg timer. */
-       unsigned int timer_ticks;       /* Number of clicks at each state  */
+       struct mii_bus mii_bus;
+       struct phy_device *phy_dev;
+       int duplex;
+       int speed;
+       int link;
+       struct work_struct restart_work;
 
        /*
         * Transmitting: Batch Mode.
@@ -475,10 +465,8 @@ struct tc35815_local {
                dma_addr_t skb_dma;
        } tx_skbs[TX_FD_NUM], rx_skbs[RX_BUF_NUM];
 #endif
-       struct mii_if_info mii;
-       unsigned short mii_id[2];
        u32 msg_enable;
-       board_t boardtype;
+       enum tc35815_chiptype chiptype;
 };
 
 static inline dma_addr_t fd_virt_to_bus(struct tc35815_local *lp, void *virt)
@@ -586,19 +574,222 @@ static const struct ethtool_ops tc35815_ethtool_ops;
 /* Example routines you must write ;->. */
 static void    tc35815_chip_reset(struct net_device *dev);
 static void    tc35815_chip_init(struct net_device *dev);
-static void    tc35815_find_phy(struct net_device *dev);
-static void    tc35815_phy_chip_init(struct net_device *dev);
 
 #ifdef DEBUG
 static void    panic_queues(struct net_device *dev);
 #endif
 
-static void tc35815_timer(unsigned long data);
-static void tc35815_start_auto_negotiation(struct net_device *dev,
-                                          struct ethtool_cmd *ep);
-static int tc_mdio_read(struct net_device *dev, int phy_id, int location);
-static void tc_mdio_write(struct net_device *dev, int phy_id, int location,
-                         int val);
+static void tc35815_restart_work(struct work_struct *work);
+
+static int tc_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+       struct net_device *dev = bus->priv;
+       struct tc35815_regs __iomem *tr =
+               (struct tc35815_regs __iomem *)dev->base_addr;
+       unsigned long timeout = jiffies + 10;
+
+       tc_writel(MD_CA_Busy | (mii_id << 5) | (regnum & 0x1f), &tr->MD_CA);
+       while (tc_readl(&tr->MD_CA) & MD_CA_Busy) {
+               if (time_after(jiffies, timeout))
+                       return -EIO;
+               cpu_relax();
+       }
+       return tc_readl(&tr->MD_Data) & 0xffff;
+}
+
+static int tc_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 val)
+{
+       struct net_device *dev = bus->priv;
+       struct tc35815_regs __iomem *tr =
+               (struct tc35815_regs __iomem *)dev->base_addr;
+       unsigned long timeout = jiffies + 10;
+
+       tc_writel(val, &tr->MD_Data);
+       tc_writel(MD_CA_Busy | MD_CA_Wr | (mii_id << 5) | (regnum & 0x1f),
+                 &tr->MD_CA);
+       while (tc_readl(&tr->MD_CA) & MD_CA_Busy) {
+               if (time_after(jiffies, timeout))
+                       return -EIO;
+               cpu_relax();
+       }
+       return 0;
+}
+
+static void tc_handle_link_change(struct net_device *dev)
+{
+       struct tc35815_local *lp = netdev_priv(dev);
+       struct phy_device *phydev = lp->phy_dev;
+       unsigned long flags;
+       int status_change = 0;
+
+       spin_lock_irqsave(&lp->lock, flags);
+       if (phydev->link &&
+           (lp->speed != phydev->speed || lp->duplex != phydev->duplex)) {
+               struct tc35815_regs __iomem *tr =
+                       (struct tc35815_regs __iomem *)dev->base_addr;
+               u32 reg;
+
+               reg = tc_readl(&tr->MAC_Ctl);
+               reg |= MAC_HaltReq;
+               tc_writel(reg, &tr->MAC_Ctl);
+               if (phydev->duplex == DUPLEX_FULL)
+                       reg |= MAC_FullDup;
+               else
+                       reg &= ~MAC_FullDup;
+               tc_writel(reg, &tr->MAC_Ctl);
+               reg &= ~MAC_HaltReq;
+               tc_writel(reg, &tr->MAC_Ctl);
+
+               /*
+                * TX4939 PCFG.SPEEDn bit will be changed on
+                * NETDEV_CHANGE event.
+                */
+
+#if !defined(NO_CHECK_CARRIER) && defined(WORKAROUND_LOSTCAR)
+               /*
+                * WORKAROUND: enable LostCrS only if half duplex
+                * operation.
+                * (TX4939 does not have EnLCarr)
+                */
+               if (phydev->duplex == DUPLEX_HALF &&
+                   lp->chiptype != TC35815_TX4939)
+                       tc_writel(tc_readl(&tr->Tx_Ctl) | Tx_EnLCarr,
+                                 &tr->Tx_Ctl);
+#endif
+
+               lp->speed = phydev->speed;
+               lp->duplex = phydev->duplex;
+               status_change = 1;
+       }
+
+       if (phydev->link != lp->link) {
+               if (phydev->link) {
+#ifdef WORKAROUND_100HALF_PROMISC
+                       /* delayed promiscuous enabling */
+                       if (dev->flags & IFF_PROMISC)
+                               tc35815_set_multicast_list(dev);
+#endif
+                       netif_schedule(dev);
+               } else {
+                       lp->speed = 0;
+                       lp->duplex = -1;
+               }
+               lp->link = phydev->link;
+
+               status_change = 1;
+       }
+       spin_unlock_irqrestore(&lp->lock, flags);
+
+       if (status_change && netif_msg_link(lp)) {
+               phy_print_status(phydev);
+#ifdef DEBUG
+               printk(KERN_DEBUG
+                      "%s: MII BMCR %04x BMSR %04x LPA %04x\n",
+                      dev->name,
+                      phy_read(phydev, MII_BMCR),
+                      phy_read(phydev, MII_BMSR),
+                      phy_read(phydev, MII_LPA));
+#endif
+       }
+}
+
+static int tc_mii_probe(struct net_device *dev)
+{
+       struct tc35815_local *lp = netdev_priv(dev);
+       struct phy_device *phydev = NULL;
+       int phy_addr;
+       u32 dropmask;
+
+       /* find the first phy */
+       for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) {
+               if (lp->mii_bus.phy_map[phy_addr]) {
+                       if (phydev) {
+                               printk(KERN_ERR "%s: multiple PHYs found\n",
+                                      dev->name);
+                               return -EINVAL;
+                       }
+                       phydev = lp->mii_bus.phy_map[phy_addr];
+                       break;
+               }
+       }
+
+       if (!phydev) {
+               printk(KERN_ERR "%s: no PHY found\n", dev->name);
+               return -ENODEV;
+       }
+
+       /* attach the mac to the phy */
+       phydev = phy_connect(dev, phydev->dev.bus_id,
+                            &tc_handle_link_change, 0,
+                            lp->chiptype == TC35815_TX4939 ?
+                            PHY_INTERFACE_MODE_RMII : PHY_INTERFACE_MODE_MII);
+       if (IS_ERR(phydev)) {
+               printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+               return PTR_ERR(phydev);
+       }
+       printk(KERN_INFO "%s: attached PHY driver [%s] "
+               "(mii_bus:phy_addr=%s, id=%x)\n",
+               dev->name, phydev->drv->name, phydev->dev.bus_id,
+               phydev->phy_id);
+
+       /* mask with MAC supported features */
+       phydev->supported &= PHY_BASIC_FEATURES;
+       dropmask = 0;
+       if (options.speed == 10)
+               dropmask |= SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full;
+       else if (options.speed == 100)
+               dropmask |= SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full;
+       if (options.duplex == 1)
+               dropmask |= SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full;
+       else if (options.duplex == 2)
+               dropmask |= SUPPORTED_10baseT_Half | SUPPORTED_100baseT_Half;
+       phydev->supported &= ~dropmask;
+       phydev->advertising = phydev->supported;
+
+       lp->link = 0;
+       lp->speed = 0;
+       lp->duplex = -1;
+       lp->phy_dev = phydev;
+
+       return 0;
+}
+
+static int tc_mii_init(struct net_device *dev)
+{
+       struct tc35815_local *lp = netdev_priv(dev);
+       int err;
+       int i;
+
+       lp->mii_bus.name = "tc35815_mii_bus";
+       lp->mii_bus.read = tc_mdio_read;
+       lp->mii_bus.write = tc_mdio_write;
+       lp->mii_bus.id = (lp->pci_dev->bus->number << 8) | lp->pci_dev->devfn;
+       lp->mii_bus.priv = dev;
+       lp->mii_bus.dev = &lp->pci_dev->dev;
+       lp->mii_bus.irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+       if (!lp->mii_bus.irq) {
+               err = -ENOMEM;
+               goto err_out;
+       }
+
+       for (i = 0; i < PHY_MAX_ADDR; i++)
+               lp->mii_bus.irq[i] = PHY_POLL;
+
+       err = mdiobus_register(&lp->mii_bus);
+       if (err)
+               goto err_out_free_mdio_irq;
+       err = tc_mii_probe(dev);
+       if (err)
+               goto err_out_unregister_bus;
+       return 0;
+
+err_out_unregister_bus:
+       mdiobus_unregister(&lp->mii_bus);
+err_out_free_mdio_irq:
+       kfree(lp->mii_bus.irq);
+err_out:
+       return err;
+}
 
 #ifdef CONFIG_CPU_TX49XX
 /*
@@ -669,8 +860,8 @@ static int __devinit tc35815_init_one (struct pci_dev *pdev,
        if (!printed_version++) {
                printk(version);
                dev_printk(KERN_DEBUG, &pdev->dev,
-                          "speed:%d duplex:%d doforce:%d\n",
-                          options.speed, options.duplex, options.doforce);
+                          "speed:%d duplex:%d\n",
+                          options.speed, options.duplex);
        }
 
        if (!pdev->irq) {
@@ -718,9 +909,10 @@ static int __devinit tc35815_init_one (struct pci_dev *pdev,
        dev->irq = pdev->irq;
        dev->base_addr = (unsigned long) ioaddr;
 
+       INIT_WORK(&lp->restart_work, tc35815_restart_work);
        spin_lock_init(&lp->lock);
        lp->pci_dev = pdev;
-       lp->boardtype = ent->driver_data;
+       lp->chiptype = ent->driver_data;
 
        lp->msg_enable = NETIF_MSG_TX_ERR | NETIF_MSG_HW | NETIF_MSG_DRV | NETIF_MSG_LINK;
        pci_set_drvdata(pdev, dev);
@@ -741,24 +933,19 @@ static int __devinit tc35815_init_one (struct pci_dev *pdev,
        memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
        printk(KERN_INFO "%s: %s at 0x%lx, %s, IRQ %d\n",
                dev->name,
-               board_info[ent->driver_data].name,
+               chip_info[ent->driver_data].name,
                dev->base_addr,
                print_mac(mac, dev->dev_addr),
                dev->irq);
 
-       setup_timer(&lp->timer, tc35815_timer, (unsigned long) dev);
-       lp->mii.dev = dev;
-       lp->mii.mdio_read = tc_mdio_read;
-       lp->mii.mdio_write = tc_mdio_write;
-       lp->mii.phy_id_mask = 0x1f;
-       lp->mii.reg_num_mask = 0x1f;
-       tc35815_find_phy(dev);
-       lp->mii.phy_id = lp->phy_addr;
-       lp->mii.full_duplex = 0;
-       lp->mii.force_media = 0;
+       rc = tc_mii_init(dev);
+       if (rc)
+               goto err_out_unregister;
 
        return 0;
 
+err_out_unregister:
+       unregister_netdev(dev);
 err_out:
        free_netdev (dev);
        return rc;
@@ -768,7 +955,11 @@ err_out:
 static void __devexit tc35815_remove_one (struct pci_dev *pdev)
 {
        struct net_device *dev = pci_get_drvdata (pdev);
+       struct tc35815_local *lp = netdev_priv(dev);
 
+       phy_disconnect(lp->phy_dev);
+       mdiobus_unregister(&lp->mii_bus);
+       kfree(lp->mii_bus.irq);
        unregister_netdev (dev);
        free_netdev (dev);
 
@@ -1098,20 +1289,14 @@ static int tc35815_tx_full(struct net_device *dev)
 static void tc35815_restart(struct net_device *dev)
 {
        struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       int do_phy_reset = 1;
-       del_timer(&lp->timer);          /* Kill if running      */
 
-       if (lp->mii_id[0] == 0x0016 && (lp->mii_id[1] & 0xfc00) == 0xf800) {
-               /* Resetting PHY cause problem on some chip... (SEEQ 80221) */
-               do_phy_reset = 0;
-       }
-       if (do_phy_reset) {
+       if (lp->phy_dev) {
                int timeout;
-               tc_mdio_write(dev, pid, MII_BMCR, BMCR_RESET);
+
+               phy_write(lp->phy_dev, MII_BMCR, BMCR_RESET);
                timeout = 100;
                while (--timeout) {
-                       if (!(tc_mdio_read(dev, pid, MII_BMCR) & BMCR_RESET))
+                       if (!(phy_read(lp->phy_dev, MII_BMCR) & BMCR_RESET))
                                break;
                        udelay(1);
                }
@@ -1119,45 +1304,53 @@ static void tc35815_restart(struct net_device *dev)
                        printk(KERN_ERR "%s: BMCR reset failed.\n", dev->name);
        }
 
+       spin_lock_irq(&lp->lock);
        tc35815_chip_reset(dev);
        tc35815_clear_queues(dev);
        tc35815_chip_init(dev);
        /* Reconfigure CAM again since tc35815_chip_init() initialize it. */
        tc35815_set_multicast_list(dev);
+       spin_unlock_irq(&lp->lock);
+
+       netif_wake_queue(dev);
 }
 
-static void tc35815_tx_timeout(struct net_device *dev)
+static void tc35815_restart_work(struct work_struct *work)
+{
+       struct tc35815_local *lp =
+               container_of(work, struct tc35815_local, restart_work);
+       struct net_device *dev = lp->dev;
+
+       tc35815_restart(dev);
+}
+
+static void tc35815_schedule_restart(struct net_device *dev)
 {
        struct tc35815_local *lp = netdev_priv(dev);
        struct tc35815_regs __iomem *tr =
                (struct tc35815_regs __iomem *)dev->base_addr;
 
+       /* disable interrupts */
+       tc_writel(0, &tr->Int_En);
+       tc_writel(tc_readl(&tr->DMA_Ctl) | DMA_IntMask, &tr->DMA_Ctl);
+       schedule_work(&lp->restart_work);
+}
+
+static void tc35815_tx_timeout(struct net_device *dev)
+{
+       struct tc35815_regs __iomem *tr =
+               (struct tc35815_regs __iomem *)dev->base_addr;
+
        printk(KERN_WARNING "%s: transmit timed out, status %#x\n",
               dev->name, tc_readl(&tr->Tx_Stat));
 
        /* Try to restart the adaptor. */
-       spin_lock_irq(&lp->lock);
-       tc35815_restart(dev);
-       spin_unlock_irq(&lp->lock);
-
+       tc35815_schedule_restart(dev);
        dev->stats.tx_errors++;
-
-       /* If we have space available to accept new transmit
-        * requests, wake up the queueing layer.  This would
-        * be the case if the chipset_init() call above just
-        * flushes out the tx queue and empties it.
-        *
-        * If instead, the tx queue is retained then the
-        * netif_wake_queue() call should be placed in the
-        * TX completion interrupt handler of the driver instead
-        * of here.
-        */
-       if (!tc35815_tx_full(dev))
-               netif_wake_queue(dev);
 }
 
 /*
- * Open/initialize the board. This is called (in the current kernel)
+ * Open/initialize the controller. This is called (in the current kernel)
  * sometime after booting when the 'ifconfig' program is run.
  *
  * This routine should set everything up anew at each open, even
@@ -1177,7 +1370,6 @@ tc35815_open(struct net_device *dev)
                return -EAGAIN;
        }
 
-       del_timer(&lp->timer);          /* Kill if running      */
        tc35815_chip_reset(dev);
 
        if (tc35815_init_queues(dev) != 0) {
@@ -1194,6 +1386,9 @@ tc35815_open(struct net_device *dev)
        tc35815_chip_init(dev);
        spin_unlock_irq(&lp->lock);
 
+       /* schedule a link state check */
+       phy_start(lp->phy_dev);
+
        /* We are now ready to accept transmit requeusts from
         * the queueing layer of the networking.
         */
@@ -1314,7 +1509,7 @@ static void tc35815_fatal_error_interrupt(struct net_device *dev, u32 status)
                panic("%s: Too many fatal errors.", dev->name);
        printk(KERN_WARNING "%s: Resetting ...\n", dev->name);
        /* Try to restart the adaptor. */
-       tc35815_restart(dev);
+       tc35815_schedule_restart(dev);
 }
 
 #ifdef TC35815_NAPI
@@ -1735,12 +1930,11 @@ tc35815_check_tx_stat(struct net_device *dev, int status)
 
 #ifndef NO_CHECK_CARRIER
        /* TX4939 does not have NCarr */
-       if (lp->boardtype == TC35815_TX4939)
+       if (lp->chiptype == TC35815_TX4939)
                status &= ~Tx_NCarr;
 #ifdef WORKAROUND_LOSTCAR
        /* WORKAROUND: ignore LostCrS in full duplex operation */
-       if ((lp->timer_state != asleep && lp->timer_state != lcheck)
-           || lp->fullduplex)
+       if (!lp->link || lp->duplex == DUPLEX_FULL)
                status &= ~Tx_NCarr;
 #endif
 #endif
@@ -1905,10 +2099,11 @@ tc35815_close(struct net_device *dev)
 #ifdef TC35815_NAPI
        napi_disable(&lp->napi);
 #endif
+       if (lp->phy_dev)
+               phy_stop(lp->phy_dev);
+       cancel_work_sync(&lp->restart_work);
 
        /* Flush the Tx and disable Rx here. */
-
-       del_timer(&lp->timer);          /* Kill if running      */
        tc35815_chip_reset(dev);
        free_irq(dev->irq, dev);
 
@@ -1993,8 +2188,8 @@ tc35815_set_multicast_list(struct net_device *dev)
                /* With some (all?) 100MHalf HUB, controller will hang
                 * if we enabled promiscuous mode before linkup... */
                struct tc35815_local *lp = netdev_priv(dev);
-               int pid = lp->phy_addr;
-               if (!(tc_mdio_read(dev, pid, MII_BMSR) & BMSR_LSTATUS))
+
+               if (!lp->link)
                        return;
 #endif
                /* Enable promiscuous mode */
@@ -2041,60 +2236,19 @@ static void tc35815_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *
 static int tc35815_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
        struct tc35815_local *lp = netdev_priv(dev);
-       spin_lock_irq(&lp->lock);
-       mii_ethtool_gset(&lp->mii, cmd);
-       spin_unlock_irq(&lp->lock);
-       return 0;
-}
-
-static int tc35815_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int rc;
-#if 1  /* use our negotiation method... */
-       /* Verify the settings we care about. */
-       if (cmd->autoneg != AUTONEG_ENABLE &&
-           cmd->autoneg != AUTONEG_DISABLE)
-               return -EINVAL;
-       if (cmd->autoneg == AUTONEG_DISABLE &&
-           ((cmd->speed != SPEED_100 &&
-             cmd->speed != SPEED_10) ||
-            (cmd->duplex != DUPLEX_HALF &&
-             cmd->duplex != DUPLEX_FULL)))
-               return -EINVAL;
 
-       /* Ok, do it to it. */
-       spin_lock_irq(&lp->lock);
-       del_timer(&lp->timer);
-       tc35815_start_auto_negotiation(dev, cmd);
-       spin_unlock_irq(&lp->lock);
-       rc = 0;
-#else
-       spin_lock_irq(&lp->lock);
-       rc = mii_ethtool_sset(&lp->mii, cmd);
-       spin_unlock_irq(&lp->lock);
-#endif
-       return rc;
+       if (!lp->phy_dev)
+               return -ENODEV;
+       return phy_ethtool_gset(lp->phy_dev, cmd);
 }
 
-static int tc35815_nway_reset(struct net_device *dev)
+static int tc35815_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
        struct tc35815_local *lp = netdev_priv(dev);
-       int rc;
-       spin_lock_irq(&lp->lock);
-       rc = mii_nway_restart(&lp->mii);
-       spin_unlock_irq(&lp->lock);
-       return rc;
-}
 
-static u32 tc35815_get_link(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int rc;
-       spin_lock_irq(&lp->lock);
-       rc = mii_link_ok(&lp->mii);
-       spin_unlock_irq(&lp->lock);
-       return rc;
+       if (!lp->phy_dev)
+               return -ENODEV;
+       return phy_ethtool_sset(lp->phy_dev, cmd);
 }
 
 static u32 tc35815_get_msglevel(struct net_device *dev)
@@ -2148,8 +2302,7 @@ static const struct ethtool_ops tc35815_ethtool_ops = {
        .get_drvinfo            = tc35815_get_drvinfo,
        .get_settings           = tc35815_get_settings,
        .set_settings           = tc35815_set_settings,
-       .nway_reset             = tc35815_nway_reset,
-       .get_link               = tc35815_get_link,
+       .get_link               = ethtool_op_get_link,
        .get_msglevel           = tc35815_get_msglevel,
        .set_msglevel           = tc35815_set_msglevel,
        .get_strings            = tc35815_get_strings,
@@ -2160,610 +2313,12 @@ static const struct ethtool_ops tc35815_ethtool_ops = {
 static int tc35815_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 {
        struct tc35815_local *lp = netdev_priv(dev);
-       int rc;
 
        if (!netif_running(dev))
                return -EINVAL;
-
-       spin_lock_irq(&lp->lock);
-       rc = generic_mii_ioctl(&lp->mii, if_mii(rq), cmd, NULL);
-       spin_unlock_irq(&lp->lock);
-
-       return rc;
-}
-
-static int tc_mdio_read(struct net_device *dev, int phy_id, int location)
-{
-       struct tc35815_regs __iomem *tr =
-               (struct tc35815_regs __iomem *)dev->base_addr;
-       u32 data;
-       tc_writel(MD_CA_Busy | (phy_id << 5) | location, &tr->MD_CA);
-       while (tc_readl(&tr->MD_CA) & MD_CA_Busy)
-               ;
-       data = tc_readl(&tr->MD_Data);
-       return data & 0xffff;
-}
-
-static void tc_mdio_write(struct net_device *dev, int phy_id, int location,
-                         int val)
-{
-       struct tc35815_regs __iomem *tr =
-               (struct tc35815_regs __iomem *)dev->base_addr;
-       tc_writel(val, &tr->MD_Data);
-       tc_writel(MD_CA_Busy | MD_CA_Wr | (phy_id << 5) | location, &tr->MD_CA);
-       while (tc_readl(&tr->MD_CA) & MD_CA_Busy)
-               ;
-}
-
-/* Auto negotiation.  The scheme is very simple.  We have a timer routine
- * that keeps watching the auto negotiation process as it progresses.
- * The DP83840 is first told to start doing it's thing, we set up the time
- * and place the timer state machine in it's initial state.
- *
- * Here the timer peeks at the DP83840 status registers at each click to see
- * if the auto negotiation has completed, we assume here that the DP83840 PHY
- * will time out at some point and just tell us what (didn't) happen.  For
- * complete coverage we only allow so many of the ticks at this level to run,
- * when this has expired we print a warning message and try another strategy.
- * This "other" strategy is to force the interface into various speed/duplex
- * configurations and we stop when we see a link-up condition before the
- * maximum number of "peek" ticks have occurred.
- *
- * Once a valid link status has been detected we configure the BigMAC and
- * the rest of the Happy Meal to speak the most efficient protocol we could
- * get a clean link for.  The priority for link configurations, highest first
- * is:
- *                 100 Base-T Full Duplex
- *                 100 Base-T Half Duplex
- *                 10 Base-T Full Duplex
- *                 10 Base-T Half Duplex
- *
- * We start a new timer now, after a successful auto negotiation status has
- * been detected.  This timer just waits for the link-up bit to get set in
- * the BMCR of the DP83840.  When this occurs we print a kernel log message
- * describing the link type in use and the fact that it is up.
- *
- * If a fatal error of some sort is signalled and detected in the interrupt
- * service routine, and the chip is reset, or the link is ifconfig'd down
- * and then back up, this entire process repeats itself all over again.
- */
-/* Note: Above comments are come from sunhme driver. */
-
-static int tc35815_try_next_permutation(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short bmcr;
-
-       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-
-       /* Downgrade from full to half duplex.  Only possible via ethtool.  */
-       if (bmcr & BMCR_FULLDPLX) {
-               bmcr &= ~BMCR_FULLDPLX;
-               printk(KERN_DEBUG "%s: try next permutation (BMCR %x)\n", dev->name, bmcr);
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-               return 0;
-       }
-
-       /* Downgrade from 100 to 10. */
-       if (bmcr & BMCR_SPEED100) {
-               bmcr &= ~BMCR_SPEED100;
-               printk(KERN_DEBUG "%s: try next permutation (BMCR %x)\n", dev->name, bmcr);
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-               return 0;
-       }
-
-       /* We've tried everything. */
-       return -1;
-}
-
-static void
-tc35815_display_link_mode(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short lpa, bmcr;
-       char *speed = "", *duplex = "";
-
-       lpa = tc_mdio_read(dev, pid, MII_LPA);
-       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-       if (options.speed ? (bmcr & BMCR_SPEED100) : (lpa & (LPA_100HALF | LPA_100FULL)))
-               speed = "100Mb/s";
-       else
-               speed = "10Mb/s";
-       if (options.duplex ? (bmcr & BMCR_FULLDPLX) : (lpa & (LPA_100FULL | LPA_10FULL)))
-               duplex = "Full Duplex";
-       else
-               duplex = "Half Duplex";
-
-       if (netif_msg_link(lp))
-               printk(KERN_INFO "%s: Link is up at %s, %s.\n",
-                      dev->name, speed, duplex);
-       printk(KERN_DEBUG "%s: MII BMCR %04x BMSR %04x LPA %04x\n",
-              dev->name,
-              bmcr, tc_mdio_read(dev, pid, MII_BMSR), lpa);
-}
-
-static void tc35815_display_forced_link_mode(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short bmcr;
-       char *speed = "", *duplex = "";
-
-       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-       if (bmcr & BMCR_SPEED100)
-               speed = "100Mb/s";
-       else
-               speed = "10Mb/s";
-       if (bmcr & BMCR_FULLDPLX)
-               duplex = "Full Duplex.\n";
-       else
-               duplex = "Half Duplex.\n";
-
-       if (netif_msg_link(lp))
-               printk(KERN_INFO "%s: Link has been forced up at %s, %s",
-                      dev->name, speed, duplex);
-}
-
-static void tc35815_set_link_modes(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       struct tc35815_regs __iomem *tr =
-               (struct tc35815_regs __iomem *)dev->base_addr;
-       int pid = lp->phy_addr;
-       unsigned short bmcr, lpa;
-       int speed;
-
-       if (lp->timer_state == arbwait) {
-               lpa = tc_mdio_read(dev, pid, MII_LPA);
-               bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-               printk(KERN_DEBUG "%s: MII BMCR %04x BMSR %04x LPA %04x\n",
-                      dev->name,
-                      bmcr, tc_mdio_read(dev, pid, MII_BMSR), lpa);
-               if (!(lpa & (LPA_10HALF | LPA_10FULL |
-                            LPA_100HALF | LPA_100FULL))) {
-                       /* fall back to 10HALF */
-                       printk(KERN_INFO "%s: bad ability %04x - falling back to 10HD.\n",
-                              dev->name, lpa);
-                       lpa = LPA_10HALF;
-               }
-               if (options.duplex ? (bmcr & BMCR_FULLDPLX) : (lpa & (LPA_100FULL | LPA_10FULL)))
-                       lp->fullduplex = 1;
-               else
-                       lp->fullduplex = 0;
-               if (options.speed ? (bmcr & BMCR_SPEED100) : (lpa & (LPA_100HALF | LPA_100FULL)))
-                       speed = 100;
-               else
-                       speed = 10;
-       } else {
-               /* Forcing a link mode. */
-               bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-               if (bmcr & BMCR_FULLDPLX)
-                       lp->fullduplex = 1;
-               else
-                       lp->fullduplex = 0;
-               if (bmcr & BMCR_SPEED100)
-                       speed = 100;
-               else
-                       speed = 10;
-       }
-
-       tc_writel(tc_readl(&tr->MAC_Ctl) | MAC_HaltReq, &tr->MAC_Ctl);
-       if (lp->fullduplex) {
-               tc_writel(tc_readl(&tr->MAC_Ctl) | MAC_FullDup, &tr->MAC_Ctl);
-       } else {
-               tc_writel(tc_readl(&tr->MAC_Ctl) & ~MAC_FullDup, &tr->MAC_Ctl);
-       }
-       tc_writel(tc_readl(&tr->MAC_Ctl) & ~MAC_HaltReq, &tr->MAC_Ctl);
-
-       /* TX4939 PCFG.SPEEDn bit will be changed on NETDEV_CHANGE event. */
-
-#ifndef NO_CHECK_CARRIER
-       /* TX4939 does not have EnLCarr */
-       if (lp->boardtype != TC35815_TX4939) {
-#ifdef WORKAROUND_LOSTCAR
-               /* WORKAROUND: enable LostCrS only if half duplex operation */
-               if (!lp->fullduplex && lp->boardtype != TC35815_TX4939)
-                       tc_writel(tc_readl(&tr->Tx_Ctl) | Tx_EnLCarr, &tr->Tx_Ctl);
-#endif
-       }
-#endif
-       lp->mii.full_duplex = lp->fullduplex;
-}
-
-static void tc35815_timer(unsigned long data)
-{
-       struct net_device *dev = (struct net_device *)data;
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short bmsr, bmcr, lpa;
-       int restart_timer = 0;
-
-       spin_lock_irq(&lp->lock);
-
-       lp->timer_ticks++;
-       switch (lp->timer_state) {
-       case arbwait:
-               /*
-                * Only allow for 5 ticks, thats 10 seconds and much too
-                * long to wait for arbitration to complete.
-                */
-               /* TC35815 need more times... */
-               if (lp->timer_ticks >= 10) {
-                       /* Enter force mode. */
-                       if (!options.doforce) {
-                               printk(KERN_NOTICE "%s: Auto-Negotiation unsuccessful,"
-                                      " cable probblem?\n", dev->name);
-                               /* Try to restart the adaptor. */
-                               tc35815_restart(dev);
-                               goto out;
-                       }
-                       printk(KERN_NOTICE "%s: Auto-Negotiation unsuccessful,"
-                              " trying force link mode\n", dev->name);
-                       printk(KERN_DEBUG "%s: BMCR %x BMSR %x\n", dev->name,
-                              tc_mdio_read(dev, pid, MII_BMCR),
-                              tc_mdio_read(dev, pid, MII_BMSR));
-                       bmcr = BMCR_SPEED100;
-                       tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-
-                       /*
-                        * OK, seems we need do disable the transceiver
-                        * for the first tick to make sure we get an
-                        * accurate link state at the second tick.
-                        */
-
-                       lp->timer_state = ltrywait;
-                       lp->timer_ticks = 0;
-                       restart_timer = 1;
-               } else {
-                       /* Anything interesting happen? */
-                       bmsr = tc_mdio_read(dev, pid, MII_BMSR);
-                       if (bmsr & BMSR_ANEGCOMPLETE) {
-                               /* Just what we've been waiting for... */
-                               tc35815_set_link_modes(dev);
-
-                               /*
-                                * Success, at least so far, advance our state
-                                * engine.
-                                */
-                               lp->timer_state = lupwait;
-                               restart_timer = 1;
-                       } else {
-                               restart_timer = 1;
-                       }
-               }
-               break;
-
-       case lupwait:
-               /*
-                * Auto negotiation was successful and we are awaiting a
-                * link up status.  I have decided to let this timer run
-                * forever until some sort of error is signalled, reporting
-                * a message to the user at 10 second intervals.
-                */
-               bmsr = tc_mdio_read(dev, pid, MII_BMSR);
-               if (bmsr & BMSR_LSTATUS) {
-                       /*
-                        * Wheee, it's up, display the link mode in use and put
-                        * the timer to sleep.
-                        */
-                       tc35815_display_link_mode(dev);
-                       netif_carrier_on(dev);
-#ifdef WORKAROUND_100HALF_PROMISC
-                       /* delayed promiscuous enabling */
-                       if (dev->flags & IFF_PROMISC)
-                               tc35815_set_multicast_list(dev);
-#endif
-#if 1
-                       lp->saved_lpa = tc_mdio_read(dev, pid, MII_LPA);
-                       lp->timer_state = lcheck;
-                       restart_timer = 1;
-#else
-                       lp->timer_state = asleep;
-                       restart_timer = 0;
-#endif
-               } else {
-                       if (lp->timer_ticks >= 10) {
-                               printk(KERN_NOTICE "%s: Auto negotiation successful, link still "
-                                      "not completely up.\n", dev->name);
-                               lp->timer_ticks = 0;
-                               restart_timer = 1;
-                       } else {
-                               restart_timer = 1;
-                       }
-               }
-               break;
-
-       case ltrywait:
-               /*
-                * Making the timeout here too long can make it take
-                * annoyingly long to attempt all of the link mode
-                * permutations, but then again this is essentially
-                * error recovery code for the most part.
-                */
-               bmsr = tc_mdio_read(dev, pid, MII_BMSR);
-               bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-               if (lp->timer_ticks == 1) {
-                       /*
-                        * Re-enable transceiver, we'll re-enable the
-                        * transceiver next tick, then check link state
-                        * on the following tick.
-                        */
-                       restart_timer = 1;
-                       break;
-               }
-               if (lp->timer_ticks == 2) {
-                       restart_timer = 1;
-                       break;
-               }
-               if (bmsr & BMSR_LSTATUS) {
-                       /* Force mode selection success. */
-                       tc35815_display_forced_link_mode(dev);
-                       netif_carrier_on(dev);
-                       tc35815_set_link_modes(dev);
-#ifdef WORKAROUND_100HALF_PROMISC
-                       /* delayed promiscuous enabling */
-                       if (dev->flags & IFF_PROMISC)
-                               tc35815_set_multicast_list(dev);
-#endif
-#if 1
-                       lp->saved_lpa = tc_mdio_read(dev, pid, MII_LPA);
-                       lp->timer_state = lcheck;
-                       restart_timer = 1;
-#else
-                       lp->timer_state = asleep;
-                       restart_timer = 0;
-#endif
-               } else {
-                       if (lp->timer_ticks >= 4) { /* 6 seconds or so... */
-                               int ret;
-
-                               ret = tc35815_try_next_permutation(dev);
-                               if (ret == -1) {
-                                       /*
-                                        * Aieee, tried them all, reset the
-                                        * chip and try all over again.
-                                        */
-                                       printk(KERN_NOTICE "%s: Link down, "
-                                              "cable problem?\n",
-                                              dev->name);
-
-                                       /* Try to restart the adaptor. */
-                                       tc35815_restart(dev);
-                                       goto out;
-                               }
-                               lp->timer_ticks = 0;
-                               restart_timer = 1;
-                       } else {
-                               restart_timer = 1;
-                       }
-               }
-               break;
-
-       case lcheck:
-               bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-               lpa = tc_mdio_read(dev, pid, MII_LPA);
-               if (bmcr & (BMCR_PDOWN | BMCR_ISOLATE | BMCR_RESET)) {
-                       printk(KERN_ERR "%s: PHY down? (BMCR %x)\n", dev->name,
-                              bmcr);
-               } else if ((lp->saved_lpa ^ lpa) &
-                          (LPA_100FULL|LPA_100HALF|LPA_10FULL|LPA_10HALF)) {
-                       printk(KERN_NOTICE "%s: link status changed"
-                              " (BMCR %x LPA %x->%x)\n", dev->name,
-                              bmcr, lp->saved_lpa, lpa);
-               } else {
-                       /* go on */
-                       restart_timer = 1;
-                       break;
-               }
-               /* Try to restart the adaptor. */
-               tc35815_restart(dev);
-               goto out;
-
-       case asleep:
-       default:
-               /* Can't happens.... */
-               printk(KERN_ERR "%s: Aieee, link timer is asleep but we got "
-                      "one anyways!\n", dev->name);
-               restart_timer = 0;
-               lp->timer_ticks = 0;
-               lp->timer_state = asleep; /* foo on you */
-               break;
-       }
-
-       if (restart_timer) {
-               lp->timer.expires = jiffies + msecs_to_jiffies(1200);
-               add_timer(&lp->timer);
-       }
-out:
-       spin_unlock_irq(&lp->lock);
-}
-
-static void tc35815_start_auto_negotiation(struct net_device *dev,
-                                          struct ethtool_cmd *ep)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short bmsr, bmcr, advertize;
-       int timeout;
-
-       netif_carrier_off(dev);
-       bmsr = tc_mdio_read(dev, pid, MII_BMSR);
-       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-       advertize = tc_mdio_read(dev, pid, MII_ADVERTISE);
-
-       if (ep == NULL || ep->autoneg == AUTONEG_ENABLE) {
-               if (options.speed || options.duplex) {
-                       /* Advertise only specified configuration. */
-                       advertize &= ~(ADVERTISE_10HALF |
-                                      ADVERTISE_10FULL |
-                                      ADVERTISE_100HALF |
-                                      ADVERTISE_100FULL);
-                       if (options.speed != 10) {
-                               if (options.duplex != 1)
-                                       advertize |= ADVERTISE_100FULL;
-                               if (options.duplex != 2)
-                                       advertize |= ADVERTISE_100HALF;
-                       }
-                       if (options.speed != 100) {
-                               if (options.duplex != 1)
-                                       advertize |= ADVERTISE_10FULL;
-                               if (options.duplex != 2)
-                                       advertize |= ADVERTISE_10HALF;
-                       }
-                       if (options.speed == 100)
-                               bmcr |= BMCR_SPEED100;
-                       else if (options.speed == 10)
-                               bmcr &= ~BMCR_SPEED100;
-                       if (options.duplex == 2)
-                               bmcr |= BMCR_FULLDPLX;
-                       else if (options.duplex == 1)
-                               bmcr &= ~BMCR_FULLDPLX;
-               } else {
-                       /* Advertise everything we can support. */
-                       if (bmsr & BMSR_10HALF)
-                               advertize |= ADVERTISE_10HALF;
-                       else
-                               advertize &= ~ADVERTISE_10HALF;
-                       if (bmsr & BMSR_10FULL)
-                               advertize |= ADVERTISE_10FULL;
-                       else
-                               advertize &= ~ADVERTISE_10FULL;
-                       if (bmsr & BMSR_100HALF)
-                               advertize |= ADVERTISE_100HALF;
-                       else
-                               advertize &= ~ADVERTISE_100HALF;
-                       if (bmsr & BMSR_100FULL)
-                               advertize |= ADVERTISE_100FULL;
-                       else
-                               advertize &= ~ADVERTISE_100FULL;
-               }
-
-               tc_mdio_write(dev, pid, MII_ADVERTISE, advertize);
-
-               /* Enable Auto-Negotiation, this is usually on already... */
-               bmcr |= BMCR_ANENABLE;
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-
-               /* Restart it to make sure it is going. */
-               bmcr |= BMCR_ANRESTART;
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-               printk(KERN_DEBUG "%s: ADVERTISE %x BMCR %x\n", dev->name, advertize, bmcr);
-
-               /* BMCR_ANRESTART self clears when the process has begun. */
-               timeout = 64;  /* More than enough. */
-               while (--timeout) {
-                       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-                       if (!(bmcr & BMCR_ANRESTART))
-                               break; /* got it. */
-                       udelay(10);
-               }
-               if (!timeout) {
-                       printk(KERN_ERR "%s: TC35815 would not start auto "
-                              "negotiation BMCR=0x%04x\n",
-                              dev->name, bmcr);
-                       printk(KERN_NOTICE "%s: Performing force link "
-                              "detection.\n", dev->name);
-                       goto force_link;
-               } else {
-                       printk(KERN_DEBUG "%s: auto negotiation started.\n", dev->name);
-                       lp->timer_state = arbwait;
-               }
-       } else {
-force_link:
-               /* Force the link up, trying first a particular mode.
-                * Either we are here at the request of ethtool or
-                * because the Happy Meal would not start to autoneg.
-                */
-
-               /* Disable auto-negotiation in BMCR, enable the duplex and
-                * speed setting, init the timer state machine, and fire it off.
-                */
-               if (ep == NULL || ep->autoneg == AUTONEG_ENABLE) {
-                       bmcr = BMCR_SPEED100;
-               } else {
-                       if (ep->speed == SPEED_100)
-                               bmcr = BMCR_SPEED100;
-                       else
-                               bmcr = 0;
-                       if (ep->duplex == DUPLEX_FULL)
-                               bmcr |= BMCR_FULLDPLX;
-               }
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr);
-
-               /* OK, seems we need do disable the transceiver for the first
-                * tick to make sure we get an accurate link state at the
-                * second tick.
-                */
-               lp->timer_state = ltrywait;
-       }
-
-       del_timer(&lp->timer);
-       lp->timer_ticks = 0;
-       lp->timer.expires = jiffies + msecs_to_jiffies(1200);
-       add_timer(&lp->timer);
-}
-
-static void tc35815_find_phy(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short id0;
-
-       /* find MII phy */
-       for (pid = 31; pid >= 0; pid--) {
-               id0 = tc_mdio_read(dev, pid, MII_BMSR);
-               if (id0 != 0xffff && id0 != 0x0000 &&
-                   (id0 & BMSR_RESV) != (0xffff & BMSR_RESV) /* paranoia? */
-                       ) {
-                       lp->phy_addr = pid;
-                       break;
-               }
-       }
-       if (pid < 0) {
-               printk(KERN_ERR "%s: No MII Phy found.\n",
-                      dev->name);
-               lp->phy_addr = pid = 0;
-       }
-
-       lp->mii_id[0] = tc_mdio_read(dev, pid, MII_PHYSID1);
-       lp->mii_id[1] = tc_mdio_read(dev, pid, MII_PHYSID2);
-       if (netif_msg_hw(lp))
-               printk(KERN_INFO "%s: PHY(%02x) ID %04x %04x\n", dev->name,
-                      pid, lp->mii_id[0], lp->mii_id[1]);
-}
-
-static void tc35815_phy_chip_init(struct net_device *dev)
-{
-       struct tc35815_local *lp = netdev_priv(dev);
-       int pid = lp->phy_addr;
-       unsigned short bmcr;
-       struct ethtool_cmd ecmd, *ep;
-
-       /* dis-isolate if needed. */
-       bmcr = tc_mdio_read(dev, pid, MII_BMCR);
-       if (bmcr & BMCR_ISOLATE) {
-               int count = 32;
-               printk(KERN_DEBUG "%s: unisolating...", dev->name);
-               tc_mdio_write(dev, pid, MII_BMCR, bmcr & ~BMCR_ISOLATE);
-               while (--count) {
-                       if (!(tc_mdio_read(dev, pid, MII_BMCR) & BMCR_ISOLATE))
-                               break;
-                       udelay(20);
-               }
-               printk(" %s.\n", count ? "done" : "failed");
-       }
-
-       if (options.speed && options.duplex) {
-               ecmd.autoneg = AUTONEG_DISABLE;
-               ecmd.speed = options.speed == 10 ? SPEED_10 : SPEED_100;
-               ecmd.duplex = options.duplex == 1 ? DUPLEX_HALF : DUPLEX_FULL;
-               ep = &ecmd;
-       } else {
-               ep = NULL;
-       }
-       tc35815_start_auto_negotiation(dev, ep);
+       if (!lp->phy_dev)
+               return -ENODEV;
+       return phy_mii_ioctl(lp->phy_dev, if_mii(rq), cmd);
 }
 
 static void tc35815_chip_reset(struct net_device *dev)
@@ -2815,8 +2370,6 @@ static void tc35815_chip_init(struct net_device *dev)
                (struct tc35815_regs __iomem *)dev->base_addr;
        unsigned long txctl = TX_CTL_CMD;
 
-       tc35815_phy_chip_init(dev);
-
        /* load station address to CAM */
        tc35815_set_cam_entry(dev, CAM_ENTRY_SOURCE, dev->dev_addr);
 
@@ -2853,12 +2406,11 @@ static void tc35815_chip_init(struct net_device *dev)
        /* start MAC transmitter */
 #ifndef NO_CHECK_CARRIER
        /* TX4939 does not have EnLCarr */
-       if (lp->boardtype == TC35815_TX4939)
+       if (lp->chiptype == TC35815_TX4939)
                txctl &= ~Tx_EnLCarr;
 #ifdef WORKAROUND_LOSTCAR
        /* WORKAROUND: ignore LostCrS in full duplex operation */
-       if ((lp->timer_state != asleep && lp->timer_state != lcheck) ||
-           lp->fullduplex)
+       if (!lp->phy_dev || !lp->link || lp->duplex == DUPLEX_FULL)
                txctl &= ~Tx_EnLCarr;
 #endif
 #endif /* !NO_CHECK_CARRIER */
@@ -2879,8 +2431,9 @@ static int tc35815_suspend(struct pci_dev *pdev, pm_message_t state)
        if (!netif_running(dev))
                return 0;
        netif_device_detach(dev);
+       if (lp->phy_dev)
+               phy_stop(lp->phy_dev);
        spin_lock_irqsave(&lp->lock, flags);
-       del_timer(&lp->timer);          /* Kill if running      */
        tc35815_chip_reset(dev);
        spin_unlock_irqrestore(&lp->lock, flags);
        pci_set_power_state(pdev, PCI_D3hot);
@@ -2891,15 +2444,14 @@ static int tc35815_resume(struct pci_dev *pdev)
 {
        struct net_device *dev = pci_get_drvdata(pdev);
        struct tc35815_local *lp = netdev_priv(dev);
-       unsigned long flags;
 
        pci_restore_state(pdev);
        if (!netif_running(dev))
                return 0;
        pci_set_power_state(pdev, PCI_D0);
-       spin_lock_irqsave(&lp->lock, flags);
        tc35815_restart(dev);
-       spin_unlock_irqrestore(&lp->lock, flags);
+       if (lp->phy_dev)
+               phy_start(lp->phy_dev);
        netif_device_attach(dev);
        return 0;
 }
@@ -2920,8 +2472,6 @@ module_param_named(speed, options.speed, int, 0);
 MODULE_PARM_DESC(speed, "0:auto, 10:10Mbps, 100:100Mbps");
 module_param_named(duplex, options.duplex, int, 0);
 MODULE_PARM_DESC(duplex, "0:auto, 1:half, 2:full");
-module_param_named(doforce, options.doforce, int, 0);
-MODULE_PARM_DESC(doforce, "try force link mode if auto-negotiation failed");
 
 static int __init tc35815_init_module(void)
 {