using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)
Signed-off-by: Steven Miao <realmz6@gmail.com>
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezbrd_partitions[] = {
{
.name = "bootloader(nor)",
static struct resource ezbrd_flash_resource = {
.start = 0x20000000,
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
.end = 0x202fffff,
#else
.end = 0x203fffff,
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = {
P_MII0_ETxD0,
static struct bfin_phydev_platform_data bfin_phydev_data[] = {
{
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
.addr = 3,
#else
.addr = 1,
.phydev_data = bfin_phydev_data,
.phy_mode = PHY_INTERFACE_MODE_MII,
.mac_peripherals = bfin_mac_peripherals,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
.phy_mask = 0xfff7, /* Only probe the port phy connect to the on chip MAC */
#endif
.vlan1_mask = 1,
}
};
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
static struct dsa_chip_data ksz8893m_switch_chip_data = {
.mii_bus = &bfin_mii_bus.dev,
.port_names = {
#endif
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-#if defined(CONFIG_NET_DSA_KSZ8893M) \
- || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
{
.modalias = "ksz8893m",
.max_speed_hz = 5000000,
#endif
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
{
.modalias = "wm8731",
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
};
/* SPI controller data */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 6,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PF8,
},
#endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
static struct bfin_sd_host bfin_sdh_data = {
.dma_chan = CH_RSI,
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
&ksz8893m_switch_device,
#endif
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
&bfin_spi1_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
&bf51x_sdh_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezbrd_flash_device,
#endif
};
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
/* setup BF518-EZBRD GPIO pin PG11 to AMS2, PG15 to AMS3. */
peripheral_request(P_AMS2, "ParaFlash");
-#if !defined(CONFIG_SPI_BFIN5XX) && !defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if !IS_ENABLED(CONFIG_SPI_BFIN5XX)
peripheral_request(P_AMS3, "ParaFlash");
#endif
return 0;
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition tcm_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
{
.modalias = "wm8731",
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
};
/* SPI controller data */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 6,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PF8,
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
static struct bfin_sd_host bfin_sdh_data = {
.dma_chan = CH_RSI,
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
&bfin_spi1_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
&bf51x_sdh_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&tcm_flash_device,
#endif
};
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xffc03800,
};
#endif
-#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_RA158Z)
static struct resource bf52x_ra158z_resources[] = {
{
.start = IRQ_PPI_ERROR,
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ad7160eval_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "linux kernel(nand)",
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 4,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 30000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7160)
#include <linux/input/ad7160.h>
static const struct ad7160_platform_data bfin_ad7160_ts_info = {
.sensor_x_res = 854,
};
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7160)
{
I2C_BOARD_INFO("ad7160", 0x33),
.irq = IRQ_PH1,
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
#include <asm/bfin_rotary.h>
static struct bfin_rotary_platform_data bfin_rotary_data = {
&bfin_dpmc,
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_RA158Z)
&bf52x_ra158z_device,
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
&bfin_rotary_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ad7160eval_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
};
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xffc03800,
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "linux kernel(nand)",
};
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20310000, /* IO PORT */
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x203FB800,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 4,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
{
.modalias = "wm8731",
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
};
#endif /* spi master and devices */
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
static struct mtd_partition cm_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PF8,
},
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
&bfin_dpmc,
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
&bfin_pcmcia_cf_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
&cm_flash_device,
#endif
};
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xffc03800,
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezbrd_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "bootloader(nand)",
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
#include <linux/spi/ad7879.h>
static const struct ad7879_platform_data bfin_ad7879_ts_info = {
.model = 7879, /* Model = AD7879 */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
{
.modalias = "ad7879",
.platform_data = &bfin_ad7879_ts_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
{
.modalias = "wm8731",
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PF8,
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
},
};
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
#include <asm/bfin-lq035q1.h>
static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
&bfin_dpmc,
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezbrd_flash_device,
#endif
};
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xffc03800,
};
#endif
-#if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_T350MCQB)
static struct resource bf52x_t350mcqb_resources[] = {
{
};
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
#include <asm/bfin-lq035q1.h>
static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "bootloader(nand)",
};
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20310000, /* IO PORT */
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x203FB800,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
#include <linux/spi/ad7879.h>
static const struct ad7879_platform_data bfin_ad7879_ts_info = {
.model = 7879, /* Model = AD7879 */
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static const u16 bfin_snd_pin[][7] = {
{P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s_pcm = {
.name = "bfin-i2s-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97_pcm = {
.name = "bfin-ac97-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
static const char * const ad1836_link[] = {
"bfin-i2s.0",
"spi0.4",
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
{
.modalias = "ad7879",
.platform_data = &bfin_ad7879_ts_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
#include <linux/mfd/adp5520.h>
/*
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PF8,
},
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
{
I2C_BOARD_INFO("ad7879", 0x2C),
.irq = IRQ_PF8,
.platform_data = (void *)&bfin_ad7879_ts_info,
},
#endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
{
I2C_BOARD_INFO("pmic-adp5520", 0x32),
.irq = IRQ_PF9,
.platform_data = (void *)&adp5520_pdev_data,
},
#endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("ad5252", 0x2f),
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1373)
{
I2C_BOARD_INFO("adau1373", 0x1A),
},
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
};
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
#include <asm/bfin_rotary.h>
static struct bfin_rotary_platform_data bfin_rotary_data = {
&bfin_dpmc,
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
&bfin_pcmcia_cf_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_T350MCQB)
&bf52x_t350mcqb_device,
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
&bfin_rotary_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
&bfin_ad1836_machine,
#endif
};
#include <asm/portmux.h>
#include <asm/dpmc.h>
-#if defined(CONFIG_TOUCHSCREEN_AD7879) \
- || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
#include <linux/spi/ad7879.h>
#define LCD_BACKLIGHT_GPIO 0x40
/* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xffc03800,
};
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
#include <asm/bfin-lq035q1.h>
static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
};
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
static struct mtd_partition tll6527m_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_DECODER)
/* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
* outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
* EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
#endif
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
#include <linux/input/adxl34x.h>
static const struct adxl34x_platform_data adxl345_info = {
.x_axis_offset = 0,
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879) \
- || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
static const struct ad7879_platform_data bfin_ad7879_ts_info = {
.model = 7879, /* Model = AD7879 */
.x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_MCP23S08)
#include <linux/spi/mcp23s08.h>
static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
.chip[0].is_present = true,
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
/*
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
- || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
{
.modalias = "ad7879",
.platform_data = &bfin_ad7879_ts_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 10000000,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_MCP23S08)
{
.modalias = "mcp23s08",
.platform_data = &bfin_mcp23s08_sys_gpio_info,
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
- || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
{
I2C_BOARD_INFO("ad7879", 0x2C),
.irq = IRQ_PH14,
.platform_data = (void *)&bfin_ad7879_ts_info,
},
#endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
{
I2C_BOARD_INFO("ltc3576", 0x09),
},
-#if defined(CONFIG_INPUT_ADXL34X_I2C) \
- || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
{
I2C_BOARD_INFO("adxl34x", 0x53),
.irq = IRQ_PH13,
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) \
- || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) \
- || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
&tll6527m_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_DECODER)
&spi_decoded_gpio,
#endif
};
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
*/
const char bfin_board_name[] = "HV Sistemas H8606";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
/*
* Driver needs to know address, irq and flag pin.
*/
- #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader (spi)",
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 16,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_8250)
#include <linux/serial_8250.h>
#include <linux/serial.h>
#endif
-#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES)
/*
* Configuration for one OpenCores keyboard controller in FPGA at address 0x20200030,
#endif
static struct platform_device *h8606_devices[] __initdata = {
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_8250)
&serial8250_device,
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_OPENCORES) || defined(CONFIG_KEYBOARD_OPENCORES_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_OPENCORES)
&opencores_kbd_device,
#endif
};
printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n");
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(h8606_devices, ARRAY_SIZE(h8606_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
return 0;
*/
const char bfin_board_name[] = "BlackStamp";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
/*
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
};
if (ret < 0)
return ret;
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
/*
* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC.
* the bfin-async-map driver takes care of flipping between
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/spi/mmc_spi.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
*/
const char bfin_board_name[] = "Bluetechnix CM BF533";
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20308000,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition para_partitions[] = {
{
.name = "bootloader(nor)",
&bfin_dpmc,
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
¶_flash_device,
#endif
};
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
return 0;
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
*/
const char bfin_board_name[] = "ADI BF533-EZKIT";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
* USB-LAN EzExtender board
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions_a[] = {
{
.name = "bootloader(nor a)",
};
#endif
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
static struct platdata_mtd_ram sram_data_a = {
.mapname = "Flash A SRAM",
.bankwidth = 2,
};
#endif
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 4,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
};
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
};
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
&bfin_dpmc,
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device_a,
&ezkit_flash_device_b,
#endif
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
&sram_device_a,
&sram_device_b,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97,
#endif
};
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <asm/irq.h>
* Driver needs to know address, irq and flag pin.
*/
#if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
#include <linux/dm9000.h>
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* if 1 - block!!! */
};
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 2,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20300000,
static struct platform_device *ip0x_devices[] __initdata = {
#if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device1,
&dm9000_device2,
#endif
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&spi_bfin_master_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
};
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/spi/mmc_spi.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
*/
const char bfin_board_name[] = "ADI BF533-STAMP";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
/*
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_BFIN_ASYNC) || defined(CONFIG_MTD_BFIN_ASYNC_MODULE)
+#if IS_ENABLED(CONFIG_MTD_BFIN_ASYNC)
static struct mtd_partition stamp_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
#define MMC_SPI_CARD_DETECT_INT IRQ_PF5
static int bfin_mmc_spi_init(struct device *dev,
irqreturn_t (*detect_int)(int, void *), void *data)
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
{
.modalias = "ad1836",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || \
- defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
static struct resource bfin_sport0_resources[] = {
{
.start = SPORT0_TCR1,
};
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+#if IS_ENABLED(CONFIG_JOYSTICK_AD7142)
{
I2C_BOARD_INFO("ad7142_joystick", 0x2C),
.irq = 39,
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = 39,
},
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("ad5252", 0x2f),
},
},
};
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
- defined(CONFIG_SND_BF5XX_AC97) || \
- defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+ IS_ENABLED(CONFIG_SND_BF5XX_AC97)
#include <asm/bfin_sport.h>
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s_pcm = {
.name = "bfin-i2s-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97_pcm = {
.name = "bfin-ac97-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
static const char * const ad1836_link[] = {
"bfin-i2s.0",
"spi0.4",
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
- defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
static const unsigned ad73311_gpio[] = {
GPIO_PF4,
};
};
#endif
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
static struct platform_device bfin_ad73311_codec_device = {
.name = "ad73311",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_SOC_AD74111) || defined(CONFIG_SND_SOC_AD74111_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD74111)
static struct platform_device bfin_ad74111_codec_device = {
.name = "ad74111",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || \
- defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || \
- defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || \
- defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
-#if defined(CONFIG_MTD_BFIN_ASYNC) || defined(CONFIG_MTD_BFIN_ASYNC_MODULE)
+#if IS_ENABLED(CONFIG_MTD_BFIN_ASYNC)
&stamp_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
&bfin_ad1836_machine,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
- defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
&bfin_ad73311_machine,
#endif
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
&bfin_ad73311_codec_device,
#endif
-#if defined(CONFIG_SND_SOC_AD74111) || defined(CONFIG_SND_SOC_AD74111_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD74111)
&bfin_ad74111_codec_device,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || \
- defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || \
- defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
&bfin_ac97,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
/* Set PF0 to 0, PF1 to 1 make /AMS3 work properly */
if (ret < 0)
return ret;
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
/*
* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC.
* the bfin-async-map driver takes care of flipping between
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
*/
const char bfin_board_name[] = "Bluetechnix CM BF537E";
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
/* SPORT SPI controller data */
static struct bfin5xx_spi_master bfin_sport_spi0_info = {
#endif /* sport spi master and devices */
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
static struct platform_device hitachi_fb_device = {
.name = "hitachi-tx09",
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20308000,
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
static struct mtd_partition cm_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) \
-|| defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
+|| IS_ENABLED(CONFIG_BFIN_SPORT)
unsigned short bfin_sport0_peripherals[] = {
P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
};
#endif
#endif
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
static struct resource bfin_sport0_resources[] = {
{
.start = SPORT0_TCR1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define PATA_INT IRQ_PF14
static struct pata_platform_info bfin_pata_platform_data = {
&bfin_dpmc,
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
&bfin_sport0_device,
#endif
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
&hitachi_fb_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
&bfin_sport_spi0_device,
&bfin_sport_spi1_device,
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
&cm_flash_device,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PG14, "net2272");
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
#endif
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
*/
const char bfin_board_name[] = "Bluetechnix CM BF537U";
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
static struct platform_device hitachi_fb_device = {
.name = "hitachi-tx09",
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20308000,
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20200000,
};
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
static struct mtd_partition cm_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define PATA_INT IRQ_PF14
static struct pata_platform_info bfin_pata_platform_data = {
&bfin_dpmc,
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
&hitachi_fb_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
&cm_flash_device,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PH15, driver_name);
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
#endif
#define FLASH_MAC 0x202f0000
#define CONFIG_MTD_PHYSMAP_LEN 0x300000
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition asmb_flash_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* use no dma transfer with this chip*/
#endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
/* This mapping is for at45db642 it has 1056 page size,
* partition size and offset should be page aligned
*/
static struct spi_board_info bfin_spi_board_info[] __initdata = {
/* SD/MMC card reader at SPI bus */
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000,
#endif
/* 8 Megabyte Atmel NOR flash chip at SPI bus */
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
{
.modalias = "mtd_dataflash",
.max_speed_hz = 16700000,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
static struct platform_device *dnp5370_devices[] __initdata = {
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&asmb_flash_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&spi_bfin_master_device,
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
*/
const char bfin_board_name[] = "CamSig Minotaur BF537";
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20310000, /* IO PORT */
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
/* Partition sizes */
#define FLASH_SIZE 0x00400000
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
static struct platform_device *minotaur_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
&bfin_pcmcia_cf_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(minotaur_devices, ARRAY_SIZE(minotaur_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info,
ARRAY_SIZE(bfin_spi_board_info));
#endif
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20310000, /* IO PORT */
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 4,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
};
#endif /* spi master and devices */
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
static struct platform_device bfin_fb_device = {
.name = "bf537-lq035",
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
static struct platform_device *stamp_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
&bfin_pcmcia_cf_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
&bfin_fb_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info,
ARRAY_SIZE(bfin_spi_board_info));
#endif
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/i2c.h>
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
};
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20310000, /* IO PORT */
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x203FB800,
};
#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_SL811_HCD)
static struct resource sl811_hcd_resources[] = {
{
.start = 0x20340000,
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20360000,
};
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
static unsigned short bfin_can_peripherals[] = {
P_CAN0_RX, P_CAN0_TX, 0
};
};
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL };
static struct mtd_partition bfin_plat_nand_partitions[] = {
static void bfin_plat_nand_init(void) {}
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition stamp_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_SPI)
#include <linux/input/ad714x.h>
static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
};
#endif
-#if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_I2C)
#include <linux/input/ad714x.h>
static struct ad714x_button_plat ad7142_i2c_button_plat[] = {
{
};
#endif
-#if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
+#if IS_ENABLED(CONFIG_AD2S90)
static struct bfin5xx_spi_chip ad2s90_spi_chip_info = {
.enable_dma = 0,
};
};
#endif
-#if defined(CONFIG_AD2S1210) || defined(CONFIG_AD2S1210_MODULE)
+#if IS_ENABLED(CONFIG_AD2S1210)
static unsigned short ad2s1210_platform_data[] = {
/* use as SAMPLE, A0, A1 */
GPIO_PF7, GPIO_PF8, GPIO_PF9,
};
#endif
-#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+#if IS_ENABLED(CONFIG_AD7816)
static unsigned short ad7816_platform_data[] = {
GPIO_PF4, /* rdwr_pin */
GPIO_PF5, /* convert_pin */
};
#endif
-#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+#if IS_ENABLED(CONFIG_ADT7310)
static unsigned long adt7310_platform_data[3] = {
/* INT bound temperature alarm event. line 1 */
IRQ_PG4, IRQF_TRIGGER_LOW,
};
#endif
-#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+#if IS_ENABLED(CONFIG_AD7298)
static unsigned short ad7298_platform_data[] = {
GPIO_PF7, /* busy_pin */
0,
};
#endif
-#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_SPI)
static unsigned long adt7316_spi_data[2] = {
IRQF_TRIGGER_LOW, /* interrupt flags */
GPIO_PF7, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
#define MMC_SPI_CARD_DETECT_INT IRQ_PF5
static int bfin_mmc_spi_init(struct device *dev,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
#include <linux/spi/ad7877.h>
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
#include <linux/spi/ad7879.h>
static const struct ad7879_platform_data bfin_ad7879_ts_info = {
.model = 7879, /* Model = AD7879 */
};
#endif
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
#include <linux/input/adxl34x.h>
static const struct adxl34x_platform_data adxl34x_info = {
.x_axis_offset = 0,
};
#endif
-#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
+#if IS_ENABLED(CONFIG_ENC28J60)
static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
.enable_dma = 1,
};
#endif
-#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
+#if IS_ENABLED(CONFIG_ADF702X)
#include <linux/spi/adf702x.h>
#define TXREG 0x0160A470
static const u32 adf7021_regs[] = {
static inline void adf702x_mac_init(void) {}
#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_ADS7846)
#include <linux/spi/ads7846.h>
static int ads7873_get_pendown_state(void)
{
};
#endif
-#if defined(CONFIG_MTD_DATAFLASH) \
- || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
static struct mtd_partition bfin_spi_dataflash_partitions[] = {
{
};
#endif
-#if defined(CONFIG_AD7476) || defined(CONFIG_AD7476_MODULE)
+#if IS_ENABLED(CONFIG_AD7476)
static struct bfin5xx_spi_chip spi_ad7476_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_MTD_DATAFLASH) \
- || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.max_speed_hz = 33250000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
{
.modalias = "ad1836",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_SPI)
{
.modalias = "ad714x_captouch",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
+#if IS_ENABLED(CONFIG_AD2S90)
{
.modalias = "ad2s90",
.bus_num = 0,
},
#endif
-#if defined(CONFIG_AD2S1210) || defined(CONFIG_AD2S1210_MODULE)
+#if IS_ENABLED(CONFIG_AD2S1210)
{
.modalias = "ad2s1210",
.max_speed_hz = 8192000,
},
#endif
-#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+#if IS_ENABLED(CONFIG_AD7816)
{
.modalias = "ad7818",
.max_speed_hz = 1000000,
},
#endif
-#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+#if IS_ENABLED(CONFIG_ADT7310)
{
.modalias = "adt7310",
.max_speed_hz = 1000000,
},
#endif
-#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+#if IS_ENABLED(CONFIG_AD7298)
{
.modalias = "ad7298",
.max_speed_hz = 1000000,
},
#endif
-#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_SPI)
{
.modalias = "adt7316",
.max_speed_hz = 1000000,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 1,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
{
.modalias = "ad7879",
.platform_data = &bfin_ad7879_ts_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 1,
},
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
-#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
+#if IS_ENABLED(CONFIG_ENC28J60)
{
.modalias = "enc28j60",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
{
.modalias = "adxl34x",
.platform_data = &adxl34x_info,
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
+#if IS_ENABLED(CONFIG_ADF702X)
{
.modalias = "adf702x",
.max_speed_hz = 16000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_ADS7846)
{
.modalias = "ads7846",
.max_speed_hz = 2000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_0,
},
#endif
-#if defined(CONFIG_AD7476) \
- || defined(CONFIG_AD7476_MODULE)
+#if IS_ENABLED(CONFIG_AD7476)
{
.modalias = "ad7476", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_ADE7753) \
- || defined(CONFIG_ADE7753_MODULE)
+#if IS_ENABLED(CONFIG_ADE7753)
{
.modalias = "ade7753",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_1,
},
#endif
-#if defined(CONFIG_ADE7754) \
- || defined(CONFIG_ADE7754_MODULE)
+#if IS_ENABLED(CONFIG_ADE7754)
{
.modalias = "ade7754",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_1,
},
#endif
-#if defined(CONFIG_ADE7758) \
- || defined(CONFIG_ADE7758_MODULE)
+#if IS_ENABLED(CONFIG_ADE7758)
{
.modalias = "ade7758",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_1,
},
#endif
-#if defined(CONFIG_ADE7759) \
- || defined(CONFIG_ADE7759_MODULE)
+#if IS_ENABLED(CONFIG_ADE7759)
{
.modalias = "ade7759",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_1,
},
#endif
-#if defined(CONFIG_ADE7854_SPI) \
- || defined(CONFIG_ADE7854_SPI_MODULE)
+#if IS_ENABLED(CONFIG_ADE7854_SPI)
{
.modalias = "ade7854",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_ADIS16060) \
- || defined(CONFIG_ADIS16060_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16060)
{
.modalias = "adis16060_r",
.max_speed_hz = 2900000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_1,
},
#endif
-#if defined(CONFIG_ADIS16130) \
- || defined(CONFIG_ADIS16130_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16130)
{
.modalias = "adis16130",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_ADIS16201) \
- || defined(CONFIG_ADIS16201_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16201)
{
.modalias = "adis16201",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16203) \
- || defined(CONFIG_ADIS16203_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16203)
{
.modalias = "adis16203",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16204) \
- || defined(CONFIG_ADIS16204_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16204)
{
.modalias = "adis16204",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16209) \
- || defined(CONFIG_ADIS16209_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16209)
{
.modalias = "adis16209",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16220) \
- || defined(CONFIG_ADIS16220_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16220)
{
.modalias = "adis16220",
.max_speed_hz = 2000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16240) \
- || defined(CONFIG_ADIS16240_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16240)
{
.modalias = "adis16240",
.max_speed_hz = 1500000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16260) \
- || defined(CONFIG_ADIS16260_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16260)
{
.modalias = "adis16260",
.max_speed_hz = 1500000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16261) \
- || defined(CONFIG_ADIS16261_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16261)
{
.modalias = "adis16261",
.max_speed_hz = 2500000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_ADIS16300) \
- || defined(CONFIG_ADIS16300_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16300)
{
.modalias = "adis16300",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16350) \
- || defined(CONFIG_ADIS16350_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16350)
{
.modalias = "adis16364",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF4,
},
#endif
-#if defined(CONFIG_ADIS16400) \
- || defined(CONFIG_ADIS16400_MODULE)
+#if IS_ENABLED(CONFIG_ADIS16400)
{
.modalias = "adis16400",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
/* SPORT SPI controller data */
static struct bfin5xx_spi_master bfin_sport_spi0_info = {
#endif /* sport spi master and devices */
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
static struct platform_device bfin_fb_device = {
.name = "bf537_lq035",
};
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
#include <asm/bfin-lq035q1.h>
static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
};
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
#include <linux/videodev2.h>
#include <media/blackfin/bfin_capture.h>
#include <media/blackfin/ppi.h>
.pin_req = ppi_req,
};
-#if defined(CONFIG_VIDEO_VS6624) \
- || defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
static struct v4l2_input vs6624_inputs[] = {
{
.index = 0,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_ADP5588)
static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
[0] = KEY_GRAVE,
[1] = KEY_1,
};
#endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
#include <linux/mfd/adp5520.h>
/*
#endif
-#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_ADP5588)
static struct adp5588_gpio_platform_data adp5588_gpio_data = {
.gpio_start = 50,
.pullup_dis_mask = 0,
};
#endif
-#if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8870)
#include <linux/i2c/adp8870.h>
static struct led_info adp8870_leds[] = {
{
};
#endif
-#if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8860)
#include <linux/i2c/adp8860.h>
static struct led_info adp8860_leds[] = {
{
};
#endif
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
static struct regulator_consumer_supply ad5398_consumer = {
.supply = "current",
};
.consumer_supplies = &ad5398_consumer,
};
-#if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
- defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_VIRTUAL_CONSUMER)
static struct platform_device ad5398_virt_consumer_device = {
.name = "reg-virt-consumer",
.id = 0,
},
};
#endif
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
- defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
static struct regulator_bulk_data ad5398_bulk_data = {
.supply = "current",
};
#endif
#endif
-#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+#if IS_ENABLED(CONFIG_ADT7410)
/* INT bound temperature alarm event. line 1 */
static unsigned long adt7410_platform_data[2] = {
IRQ_PG4, IRQF_TRIGGER_LOW,
};
#endif
-#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_I2C)
/* INT bound temperature alarm event. line 1 */
static unsigned long adt7316_i2c_data[2] = {
IRQF_TRIGGER_LOW, /* interrupt flags */
},
#endif
-#if defined(CONFIG_SND_SOC_ADAV80X) || defined(CONFIG_SND_SOC_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAV80X)
{
I2C_BOARD_INFO("adav803", 0x10),
},
#endif
-#if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_AD714X_I2C)
{
I2C_BOARD_INFO("ad7142_captouch", 0x2C),
.irq = IRQ_PG5,
},
#endif
-#if defined(CONFIG_AD7150) || defined(CONFIG_AD7150_MODULE)
+#if IS_ENABLED(CONFIG_AD7150)
{
I2C_BOARD_INFO("ad7150", 0x48),
.irq = IRQ_PG5, /* fixme: use real interrupt number */
},
#endif
-#if defined(CONFIG_AD7152) || defined(CONFIG_AD7152_MODULE)
+#if IS_ENABLED(CONFIG_AD7152)
{
I2C_BOARD_INFO("ad7152", 0x48),
},
#endif
-#if defined(CONFIG_AD774X) || defined(CONFIG_AD774X_MODULE)
+#if IS_ENABLED(CONFIG_AD774X)
{
I2C_BOARD_INFO("ad774x", 0x48),
},
#endif
-#if defined(CONFIG_ADE7854_I2C) || defined(CONFIG_ADE7854_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADE7854_I2C)
{
I2C_BOARD_INFO("ade7854", 0x38),
},
},
#endif
-#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+#if IS_ENABLED(CONFIG_ADT7410)
{
I2C_BOARD_INFO("adt7410", 0x48),
/* CT critical temperature event. line 0 */
},
#endif
-#if defined(CONFIG_AD7291) || defined(CONFIG_AD7291_MODULE)
+#if IS_ENABLED(CONFIG_AD7291)
{
I2C_BOARD_INFO("ad7291", 0x20),
.irq = IRQ_PG5,
},
#endif
-#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+#if IS_ENABLED(CONFIG_ADT7316_I2C)
{
I2C_BOARD_INFO("adt7316", 0x48),
.irq = IRQ_PG6,
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PG6,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_I2C)
{
I2C_BOARD_INFO("ad7879", 0x2F),
.irq = IRQ_PG5,
.platform_data = (void *)&bfin_ad7879_ts_info,
},
#endif
-#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_ADP5588)
{
I2C_BOARD_INFO("adp5588-keys", 0x34),
.irq = IRQ_PG0,
.platform_data = (void *)&adp5588_kpad_data,
},
#endif
-#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#if IS_ENABLED(CONFIG_PMIC_ADP5520)
{
I2C_BOARD_INFO("pmic-adp5520", 0x32),
.irq = IRQ_PG0,
.platform_data = (void *)&adp5520_pdev_data,
},
#endif
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
{
I2C_BOARD_INFO("adxl34x", 0x53),
.irq = IRQ_PG3,
.platform_data = (void *)&adxl34x_info,
},
#endif
-#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#if IS_ENABLED(CONFIG_GPIO_ADP5588)
{
I2C_BOARD_INFO("adp5588-gpio", 0x34),
.platform_data = (void *)&adp5588_gpio_data,
},
#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_7393)
{
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
{
I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2F),
},
#endif
-#if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8870)
{
I2C_BOARD_INFO("adp8870", 0x2B),
.platform_data = (void *)&adp8870_pdata,
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1371) || defined(CONFIG_SND_SOC_ADAU1371_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1371)
{
I2C_BOARD_INFO("adau1371", 0x1A),
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
{
I2C_BOARD_INFO("adau1761", 0x38),
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1361) || defined(CONFIG_SND_SOC_ADAU1361_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1361)
{
I2C_BOARD_INFO("adau1361", 0x38),
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1701) || defined(CONFIG_SND_SOC_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1701)
{
I2C_BOARD_INFO("adau1701", 0x34),
},
#endif
-#if defined(CONFIG_AD525X_DPOT) || defined(CONFIG_AD525X_DPOT_MODULE)
+#if IS_ENABLED(CONFIG_AD525X_DPOT)
{
I2C_BOARD_INFO("ad5258", 0x18),
},
#endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
#endif
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
{
I2C_BOARD_INFO("ad5398", 0xC),
.platform_data = (void *)&ad5398_regulator_data,
},
#endif
-#if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
+#if IS_ENABLED(CONFIG_BACKLIGHT_ADP8860)
{
I2C_BOARD_INFO("adp8860", 0x2A),
.platform_data = (void *)&adp8860_pdata,
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1373)
{
I2C_BOARD_INFO("adau1373", 0x1A),
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("ad5252", 0x2e),
},
#endif
};
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) \
-|| defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
+|| IS_ENABLED(CONFIG_BFIN_SPORT)
unsigned short bfin_sport0_peripherals[] = {
P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
};
#endif
#endif
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
static struct resource bfin_sport0_resources[] = {
{
.start = SPORT0_TCR1,
},
};
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
/* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
},
};
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
- defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+ IS_ENABLED(CONFIG_SND_BF5XX_AC97)
#define SPORT_REQ(x) \
[x] = {P_SPORT##x##_TFS, P_SPORT##x##_DTPRI, P_SPORT##x##_TSCLK, \
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s_pcm = {
.name = "bfin-i2s-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97_pcm = {
.name = "bfin-ac97-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
static const char * const ad1836_link[] = {
"bfin-i2s.0",
"spi0.4",
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
- defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
static const unsigned ad73311_gpio[] = {
GPIO_PF4,
};
};
#endif
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
static struct platform_device bfin_ad73311_codec_device = {
.name = "ad73311",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X)
static struct platform_device bfin_eval_adav801_device = {
.name = "bfin-eval-adav801",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_FIXED_VOLTAGE)
#define REGULATOR_ADP122 "adp122"
#define REGULATOR_ADP122_UV 2500000
},
};
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
- defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
static struct regulator_bulk_data adp122_bulk_data = {
.supply = REGULATOR_ADP122,
};
#endif
#endif
-#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
- defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+#if IS_ENABLED(CONFIG_IIO_GPIO_TRIGGER)
static struct resource iio_gpio_trigger_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373)
static struct platform_device bf5xx_adau1373_device = {
.name = "bfin-eval-adau1373",
};
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701)
static struct platform_device bf5xx_adau1701_device = {
.name = "bfin-eval-adau1701",
};
static struct platform_device *stamp_devices[] __initdata = {
&bfin_dpmc,
-#if defined(CONFIG_BFIN_SPORT) || defined(CONFIG_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SPORT)
&bfin_sport0_device,
#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_CFPCMCIA)
&bfin_pcmcia_cf_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_SL811_HCD)
&sl811_hcd_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device,
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
&bfin_can_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
&bfin_sport_spi0_device,
&bfin_sport_spi1_device,
#endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF537_LQ035)
&bfin_fb_device,
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
&bfin_capture_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
&bfin_async_nand_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&stamp_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
&bfin_ad1836_machine,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || \
- defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
&bfin_ad73311_machine,
#endif
-#if defined(CONFIG_SND_SOC_AD73311) || defined(CONFIG_SND_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_AD73311)
&bfin_ad73311_codec_device,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
&bfin_ac97,
#endif
-#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
-#if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
- defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_AD5398)
+#if IS_ENABLED(CONFIG_REGULATOR_VIRTUAL_CONSUMER)
&ad5398_virt_consumer_device,
#endif
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
- defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
&ad5398_userspace_consumer_device,
#endif
#endif
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_FIXED_VOLTAGE)
&adp_switch_device,
-#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
- defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
+#if IS_ENABLED(CONFIG_REGULATOR_USERSPACE_CONSUMER)
&adp122_userspace_consumer_device,
#endif
#endif
-#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
- defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+#if IS_ENABLED(CONFIG_IIO_GPIO_TRIGGER)
&iio_gpio_trigger,
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1373)
&bf5xx_adau1373_device,
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1701)
&bf5xx_adau1701_device,
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAV80X)
&bfin_eval_adav801_device,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PF6, "net2272");
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
*/
const char bfin_board_name[] = "Bluetechnix TCM BF537";
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
};
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
static struct platform_device hitachi_fb_device = {
.name = "hitachi-tx09",
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20308000,
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x20300000,
};
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
static struct mtd_partition cm_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_MII0;
};
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define PATA_INT IRQ_PF14
static struct pata_platform_info bfin_pata_platform_data = {
&bfin_dpmc,
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
&hitachi_fb_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
&bfin_mii_bus,
&bfin_mac_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
&cm_flash_device,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PG14, "net2272");
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
#endif
*/
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif /* CONFIG_RTC_DRV_BFIN */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif /* CONFIG_SERIAL_BFIN_UART2 */
#endif /* CONFIG_SERIAL_BFIN */
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif /* CONFIG_BFIN_SIR2 */
#endif /* CONFIG_BFIN_SIR */
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif /* CONFIG_SERIAL_BFIN_SPORT3_UART */
#endif /* CONFIG_SERIAL_BFIN_SPORT */
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
static unsigned short bfin_can_peripherals[] = {
P_CAN0_RX, P_CAN0_TX, 0
};
* USB-LAN EzExtender board
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif /* CONFIG_SMC91X */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
/* SPI flash chip (m25p16) */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
#endif /* CONFIG_MTD_M25P80 */
#endif /* CONFIG_SPI_BFIN5XX */
-#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
#include <linux/spi/ad7879.h>
static const struct ad7879_platform_data bfin_ad7879_ts_info = {
.model = 7879, /* Model = AD7879 */
};
#endif /* CONFIG_TOUCHSCREEN_AD7879 */
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
#include <asm/bfin-lq035q1.h>
static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
#endif /* CONFIG_FB_BFIN_LQ035Q1 */
static struct spi_board_info bf538_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif /* CONFIG_MTD_M25P80 */
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
{
.modalias = "ad7879",
.platform_data = &bfin_ad7879_ts_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif /* CONFIG_TOUCHSCREEN_AD7879_SPI */
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
{
.modalias = "bfin-lq035q1-spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_CPHA | SPI_CPOL,
},
#endif /* CONFIG_FB_BFIN_LQ035Q1 */
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
},
};
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
};
#endif /* CONFIG_I2C_BLACKFIN_TWI */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
},
};
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
static struct resource ezkit_flash_resource = {
.start = 0x20000000,
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
.end = 0x202fffff,
#else
.end = 0x203fffff,
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bf538_spi_master0,
&bf538_spi_master1,
&bf538_spi_master2,
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi0_device,
&i2c_bfin_twi1_device,
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
&bfin_can_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
&bfin_lq035q1_device,
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
};
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf538_devices, ARRAY_SIZE(cm_bf538_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bf538_spi_board_info,
ARRAY_SIZE(bf538_spi_board_info));
#endif
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
#include <mach/bf54x-lq043.h>
};
#endif
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
static unsigned int bf548_keymap[] = {
KEYVAL(0, 0, KEY_ENTER),
KEYVAL(0, 1, KEY_HELP),
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
};
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xFFC03C00,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
static struct resource bfin_atapi_resources[] = {
{
.start = 0xFFC03800,
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "linux kernel(nand)",
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
static struct bfin_sd_host bfin_sdh_data = {
.dma_chan = CH_SDH,
.irq_int0 = IRQ_SDH_MASK0,
};
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
static unsigned short bfin_can_peripherals[] = {
P_CAN0_RX, P_CAN0_TX, 0
};
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition para_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
/* SPI flash chip (m25p16) */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bf54x_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = 2,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
};
#endif /* spi master and devices */
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
&bfin_dpmc,
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
&bf54x_lq043_device,
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
&bfin_atapi_device,
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
&bf54x_sdh_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bf54x_spi_master0,
&bf54x_spi_master1,
#endif
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
&bf54x_kpad_device,
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi0_device,
#if !defined(CONFIG_BF542)
&i2c_bfin_twi1_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
¶_flash_device,
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
&bfin_can_device,
#endif
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf548_devices, ARRAY_SIZE(cm_bf548_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bf54x_spi_board_info,
ARRAY_SIZE(bf54x_spi_board_info));
#endif
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
#include <mach/bf54x-lq043.h>
};
#endif
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
static const unsigned int bf548_keymap[] = {
KEYVAL(0, 0, KEY_ENTER),
KEYVAL(0, 1, KEY_HELP),
};
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
#include <asm/bfin_rotary.h>
static struct bfin_rotary_platform_data bfin_rotary_data = {
};
#endif
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
#include <linux/input/adxl34x.h>
static const struct adxl34x_platform_data adxl34x_info = {
.x_axis_offset = 0,
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
};
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xFFC03C00,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
static unsigned short bfin_can0_peripherals[] = {
P_CAN0_RX, P_CAN0_TX, 0
#endif
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
static struct resource bfin_atapi_resources[] = {
{
.start = 0xFFC03800,
};
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "bootloader(nand)",
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
static struct bfin_sd_host bfin_sdh_data = {
.dma_chan = CH_SDH,
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
/* SPI flash chip (m25p16) */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = MAX_CTRL_CS + GPIO_PG6, /* SPI_SSEL2 */
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = MAX_CTRL_CS + GPIO_PE5, /* SPI_SSEL2 */
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = MAX_CTRL_CS + GPIO_PE4, /* SPI_SSEL1 */
},
#endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
{
.modalias = "adxl34x",
.platform_data = &adxl34x_info,
},
#endif
};
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
};
#endif /* spi master and devices */
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
#include <linux/videodev2.h>
#include <media/blackfin/bfin_capture.h>
#include <media/blackfin/ppi.h>
.pin_req = ppi_req,
};
-#if defined(CONFIG_VIDEO_VS6624) \
- || defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
static struct v4l2_input vs6624_inputs[] = {
{
.index = 0,
};
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = 212,
},
#endif
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
{
I2C_BOARD_INFO("adxl34x", 0x53),
.irq = IRQ_PC5,
.platform_data = (void *)&adxl34x_info,
},
#endif
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
{
I2C_BOARD_INFO("ad5252", 0x2f),
},
};
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
},
};
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
- defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S) || \
+ IS_ENABLED(CONFIG_SND_BF5XX_AC97)
#define SPORT_REQ(x) \
[x] = {P_SPORT##x##_TFS, P_SPORT##x##_DTPRI, P_SPORT##x##_TSCLK, \
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s_pcm = {
.name = "bfin-i2s-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97_pcm = {
.name = "bfin-ac97-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD73311) || defined(CONFIG_SND_BF5XX_SOC_AD73311_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD73311)
static struct platform_device bfin_ad73311_codec_device = {
.name = "ad73311",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1980) || defined(CONFIG_SND_BF5XX_SOC_AD1980_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980)
static struct platform_device bfin_ad1980_codec_device = {
.name = "ad1980",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_I2S) || defined(CONFIG_SND_BF5XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AC97) || defined(CONFIG_SND_BF5XX_SOC_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
&bfin_gpj_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+#if IS_ENABLED(CONFIG_FB_BF54X_LQ043)
&bf54x_lq043_device,
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
&bfin_can0_device,
&bfin_can1_device,
#endif
-#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+#if IS_ENABLED(CONFIG_PATA_BF54X)
&bfin_atapi_device,
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bf5xx_nand_device,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
&bf54x_sdh_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bf54x_spi_master0,
&bf54x_spi_master1,
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
&bfin_capture_device,
#endif
-#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_BFIN)
&bf54x_kpad_device,
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
&bfin_rotary_device,
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi0_device,
#if !defined(CONFIG_BF542)
&i2c_bfin_twi1_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97_pcm,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1980) || defined(CONFIG_SND_BF5XX_SOC_AD1980_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1980)
&bfin_ad1980_codec_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97,
#endif
};
*/
const char bfin_board_name[] = "Acvilon board";
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
},
};
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
static struct platdata_mtd_ram mtd_ram_data = {
.mapname = "rootfs(RAM)",
.bankwidth = 4,
};
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
{
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
static struct mtd_partition bfin_plat_nand_partitions[] = {
{
}
#endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
static struct mtd_partition bfin_spi_dataflash_partitions[] = {
{
.name = "bootloader",
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 3,
},
#endif
-#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
+#if IS_ENABLED(CONFIG_MTD_DATAFLASH)
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.max_speed_hz = 33250000, /* max spi clock (SCK) speed in HZ */
static struct platform_device *acvilon_devices[] __initdata = {
&bfin_dpmc,
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
&bfin_gpios_device,
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
&bfin_i2c_pca_device,
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
&bfin_async_nand_device,
#endif
-#if defined(CONFIG_MTD_PLATRAM) || defined(CONFIG_MTD_PLATRAM_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PLATRAM)
&mtd_ram_device,
#endif
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <linux/ata_platform.h>
*/
const char bfin_board_name[] = "Bluetechnix CM BF561";
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
},
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.chip_select = 4,
},
#endif
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
#endif /* spi master and devices */
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
static struct platform_device hitachi_fb_device = {
.name = "hitachi-tx09",
};
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
#include <linux/smsc911x.h>
static struct resource smsc911x_resources[] = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x24000000,
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x24008000,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
#define PATA_INT IRQ_PF46
static struct pata_platform_info bfin_pata_platform_data = {
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition para_partitions[] = {
{
.name = "bootloader(nor)",
&bfin_dpmc,
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
&hitachi_fb_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#if IS_ENABLED(CONFIG_SMSC911X)
&smsc911x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
&bfin_pata_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
¶_flash_device,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PF46, "net2272");
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices));
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#if IS_ENABLED(CONFIG_PATA_PLATFORM)
irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
#endif
*/
const char bfin_board_name[] = "ADI BF561-EZKIT";
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
static struct resource isp1362_hcd_resources[] = {
};
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
static struct resource net2272_bfin_resources[] = {
{
.start = 0x2C000000,
* USB-LAN EzExtender board
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
- || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
#endif
};
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
};
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
},
};
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
#include <linux/videodev2.h>
#include <media/blackfin/bfin_capture.h>
#include <media/blackfin/ppi.h>
.pin_req = ppi_req,
};
-#if defined(CONFIG_VIDEO_ADV7183) \
- || defined(CONFIG_VIDEO_ADV7183_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7183)
#include <media/adv7183.h>
static struct v4l2_input adv7183_inputs[] = {
{
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
static struct platform_device bfin_ac97 = {
.name = "bfin-ac97",
.id = CONFIG_SND_BF5XX_SPORT_NUM,
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
static const char * const ad1836_link[] = {
"bfin-i2s.0",
"spi0.4",
&bfin_dpmc,
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
&net2272_bfin_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
&bfin_capture_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_AC97)
&bfin_ac97,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
&bfin_ad1836_machine,
#endif
};
static int __init net2272_init(void)
{
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+#if IS_ENABLED(CONFIG_USB_NET2272)
int ret;
ret = gpio_request(GPIO_PF11, "net2272");
if (ret < 0)
return ret;
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#if IS_ENABLED(CONFIG_SMC91X)
bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 12));
SSYNC();
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
bfin_write_FIO0_FLAG_S(1 << 15);
SSYNC();
.resource = smc91x_resources,
};
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
static struct platform_device *tepla_devices[] __initdata = {
&smc91x_device,
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
* Driver needs to know address, irq and flag pin.
*/
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
#include <linux/usb/isp1760.h>
static struct resource bfin_isp1760_resources[] = {
[0] = {
};
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
#include <asm/bfin_rotary.h>
static struct bfin_rotary_platform_data bfin_rotary_data = {
};
#endif
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
#include <linux/stmmac.h>
#include <linux/phy.h>
};
#endif
-#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X)
#include <linux/input/adxl34x.h>
static const struct adxl34x_platform_data adxl34x_info = {
.x_axis_offset = 0,
};
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct resource musb_resources[] = {
[0] = {
.start = 0xFFCC1000,
};
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
static unsigned short bfin_can0_peripherals[] = {
P_CAN0_RX, P_CAN0_TX, 0
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
static struct mtd_partition partition_info[] = {
{
.name = "bootloader(nand)",
};
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
static struct bfin_sd_host bfin_sdh_data = {
.dma_chan = CH_RSI,
};
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
};
#endif
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
/* SPI flash chip (w25q32) */
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
};
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
static struct bfin_spi3_chip spidev_chip_info = {
.enable_dma = true,
};
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
static struct platform_device bfin_i2s_pcm = {
.name = "bfin-i2s-pcm-audio",
.id = -1,
};
#endif
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
- defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
#include <asm/bfin_sport3.h>
static struct resource bfin_snd_resources[] = {
{
};
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
- || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
static const char * const ad1836_link[] = {
"bfin-i2s.0",
"spi0.76",
};
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
static struct platform_device adau1761_device = {
.name = "bfin-eval-adau1x61",
};
#endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
#include <sound/adau17x1.h>
static struct adau1761_platform_data adau1761_info = {
.lineout_mode = ADAU1761_OUTPUT_MODE_LINE,
};
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
#include <linux/videodev2.h>
#include <media/blackfin/bfin_capture.h>
#include <media/blackfin/ppi.h>
P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7,
P_PPI0_D8, P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
P_PPI0_D12, P_PPI0_D13, P_PPI0_D14, P_PPI0_D15,
-#if !defined(CONFIG_VIDEO_VS6624) && !defined(CONFIG_VIDEO_VS6624_MODULE)
+#if !IS_ENABLED(CONFIG_VIDEO_VS6624)
P_PPI0_D16, P_PPI0_D17, P_PPI0_D18, P_PPI0_D19,
P_PPI0_D20, P_PPI0_D21, P_PPI0_D22, P_PPI0_D23,
#endif
.pin_req = ppi_req,
};
-#if defined(CONFIG_VIDEO_VS6624) \
- || defined(CONFIG_VIDEO_VS6624_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_VS6624)
static struct v4l2_input vs6624_inputs[] = {
{
.index = 0,
};
#endif
-#if defined(CONFIG_VIDEO_ADV7842) \
- || defined(CONFIG_VIDEO_ADV7842_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7842)
#include <media/adv7842.h>
static struct v4l2_input adv7842_inputs[] = {
};
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
- || defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
#include <linux/videodev2.h>
#include <media/blackfin/bfin_display.h>
#include <media/blackfin/ppi.h>
.pin_req = ppi_req_disp,
};
-#if defined(CONFIG_VIDEO_ADV7511) \
- || defined(CONFIG_VIDEO_ADV7511_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_ADV7511)
#include <media/adv7511.h>
static struct v4l2_output adv7511_outputs[] = {
};
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
{
.modalias = "ad7877",
.platform_data = &bfin_ad7877_ts_info,
.chip_select = MAX_CTRL_CS + GPIO_PC15, /* SPI_SSEL4 */
},
#endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.controller_data = &spidev_chip_info,
},
#endif
-#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_SPI)
{
.modalias = "adxl34x",
.platform_data = &adxl34x_info,
};
#endif /* spi master and devices */
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
static struct resource bfin_twi0_resource[] = {
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
-#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_ADXL34X_I2C)
{
I2C_BOARD_INFO("adxl34x", 0x53),
.irq = IRQ_PC5,
.platform_data = (void *)&adxl34x_info,
},
#endif
-#if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_ADAU1761)
{
I2C_BOARD_INFO("adau1761", 0x38),
.platform_data = (void *)&adau1761_info
},
#endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
{
I2C_BOARD_INFO("ssm2602", 0x1b),
},
&bfin_gpg_device,
#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#endif
-#if defined(CONFIG_STMMAC_ETH) || defined(CONFIG_STMMAC_ETH_MODULE)
+#if IS_ENABLED(CONFIG_STMMAC_ETH)
&bfin_eth_device,
#endif
-#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
&musb_device,
#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1760_HCD)
&bfin_isp1760_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#endif
#endif
-#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_CAN_BFIN)
&bfin_can0_device,
#endif
-#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
&bfin_nand_device,
#endif
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
&bfin_sdh_device,
#endif
&bf60x_spi_master1,
#endif
-#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_BFIN_ROTARY)
&bfin_rotary_device,
#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
&i2c_bfin_twi0_device,
#if !defined(CONFIG_BF542)
&i2c_bfin_twi1_device,
&bfin_crypto_crc_device,
#endif
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
&ezkit_flash_device,
#endif
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
&bfin_i2s_pcm,
#endif
-#if defined(CONFIG_SND_BF6XX_SOC_I2S) || \
- defined(CONFIG_SND_BF6XX_SOC_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF6XX_SOC_I2S)
&bfin_i2s,
#endif
-#if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
- defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD1836)
&bfin_ad1836_machine,
#endif
-#if defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61) || \
- defined(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61)
&adau1761_device,
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
- || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_CAPTURE)
&bfin_capture_device,
#endif
-#if defined(CONFIG_VIDEO_BLACKFIN_DISPLAY) \
- || defined(CONFIG_VIDEO_BLACKFIN_DISPLAY_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_BLACKFIN_DISPLAY)
&bfin_display_device,
#endif
PIN_MAP_MUX_GROUP_DEFAULT("physmap-flash.0", "pinctrl-adi2.0", NULL, "smc0"),
PIN_MAP_MUX_GROUP_DEFAULT("bf609_nl8048.2", "pinctrl-adi2.0", NULL, "ppi2_16b"),
PIN_MAP_MUX_GROUP_DEFAULT("bfin_display.0", "pinctrl-adi2.0", NULL, "ppi0_16b"),
-#if defined(CONFIG_VIDEO_MT9M114) || defined(CONFIG_VIDEO_MT9M114_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_MT9M114)
PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0", "pinctrl-adi2.0", NULL, "ppi0_8b"),
-#elif defined(CONFIG_VIDEO_VS6624) || defined(CONFIG_VIDEO_VS6624_MODULE)
+#elif IS_ENABLED(CONFIG_VIDEO_VS6624)
PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0", "pinctrl-adi2.0", NULL, "ppi0_16b"),
#else
PIN_MAP_MUX_GROUP_DEFAULT("bfin_capture.0", "pinctrl-adi2.0", NULL, "ppi0_24b"),
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff