return status;
}
-/** ixgbe_init_mac_link_ops_X550em - init mac link function pointers
- * @hw: pointer to hardware structure
- **/
-static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw)
-{
- struct ixgbe_mac_info *mac = &hw->mac;
-
- /* CS4227 does not support autoneg, so disable the laser control
- * functions for SFP+ fiber
- */
- if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP) {
- mac->ops.disable_tx_laser = NULL;
- mac->ops.enable_tx_laser = NULL;
- mac->ops.flap_tx_laser = NULL;
- }
-}
-
-/** ixgbe_setup_sfp_modules_X550em - Setup SFP module
- * @hw: pointer to hardware structure
- */
-static s32 ixgbe_setup_sfp_modules_X550em(struct ixgbe_hw *hw)
-{
- bool setup_linear;
- u16 reg_slice, edc_mode;
- s32 ret_val;
-
- switch (hw->phy.sfp_type) {
- case ixgbe_sfp_type_unknown:
- return 0;
- case ixgbe_sfp_type_not_present:
- return IXGBE_ERR_SFP_NOT_PRESENT;
- case ixgbe_sfp_type_da_cu_core0:
- case ixgbe_sfp_type_da_cu_core1:
- setup_linear = true;
- break;
- case ixgbe_sfp_type_srlr_core0:
- case ixgbe_sfp_type_srlr_core1:
- case ixgbe_sfp_type_da_act_lmt_core0:
- case ixgbe_sfp_type_da_act_lmt_core1:
- case ixgbe_sfp_type_1g_sx_core0:
- case ixgbe_sfp_type_1g_sx_core1:
- setup_linear = false;
- break;
- default:
- return IXGBE_ERR_SFP_NOT_SUPPORTED;
- }
-
- ixgbe_init_mac_link_ops_X550em(hw);
- hw->phy.ops.reset = NULL;
-
- /* The CS4227 slice address is the base address + the port-pair reg
- * offset. I.e. Slice 0 = 0x12B0 and slice 1 = 0x22B0.
- */
- reg_slice = IXGBE_CS4227_SPARE24_LSB + (hw->bus.lan_id << 12);
-
- if (setup_linear)
- edc_mode = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
- else
- edc_mode = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
-
- /* Configure CS4227 for connection type. */
- ret_val = hw->phy.ops.write_i2c_combined(hw, IXGBE_CS4227, reg_slice,
- edc_mode);
-
- if (ret_val)
- ret_val = hw->phy.ops.write_i2c_combined(hw, 0x80, reg_slice,
- edc_mode);
-
- return ret_val;
-}
-
-/** ixgbe_get_link_capabilities_x550em - Determines link capabilities
- * @hw: pointer to hardware structure
- * @speed: pointer to link speed
- * @autoneg: true when autoneg or autotry is enabled
- **/
-static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw,
- ixgbe_link_speed *speed,
- bool *autoneg)
-{
- /* SFP */
- if (hw->phy.media_type == ixgbe_media_type_fiber) {
- /* CS4227 SFP must not enable auto-negotiation */
- *autoneg = false;
-
- if (hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
- hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
- *speed = IXGBE_LINK_SPEED_1GB_FULL;
- return 0;
- }
-
- /* Link capabilities are based on SFP */
- if (hw->phy.multispeed_fiber)
- *speed = IXGBE_LINK_SPEED_10GB_FULL |
- IXGBE_LINK_SPEED_1GB_FULL;
- else
- *speed = IXGBE_LINK_SPEED_10GB_FULL;
- } else {
- *speed = IXGBE_LINK_SPEED_10GB_FULL |
- IXGBE_LINK_SPEED_1GB_FULL;
- *autoneg = true;
- }
- return 0;
-}
-
/** ixgbe_write_iosf_sb_reg_x550 - Writes a value to specified register of the
* IOSF device
*
return status;
}
+/**
+ * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Setup internal/external PHY link speed based on link speed, then set
+ * external PHY auto advertised link speed.
+ *
+ * Returns error status for any failure
+ **/
+static s32 ixgbe_setup_mac_link_t_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait)
+{
+ s32 status;
+ ixgbe_link_speed force_speed;
+
+ /* Setup internal/external PHY link speed to iXFI (10G), unless
+ * only 1G is auto advertised then setup KX link.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ force_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ else
+ force_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If internal link mode is XFI, then setup XFI internal link. */
+ if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ status = ixgbe_setup_ixfi_x550em(hw, &force_speed);
+
+ if (status)
+ return status;
+ }
+
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/** ixgbe_init_mac_link_ops_X550em - init mac link function pointers
+ * @hw: pointer to hardware structure
+ **/
+static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+
+ switch (mac->ops.get_media_type(hw)) {
+ case ixgbe_media_type_fiber:
+ /* CS4227 does not support autoneg, so disable the laser control
+ * functions for SFP+ fiber
+ */
+ mac->ops.disable_tx_laser = NULL;
+ mac->ops.enable_tx_laser = NULL;
+ mac->ops.flap_tx_laser = NULL;
+ break;
+ case ixgbe_media_type_copper:
+ mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
+ break;
+ default:
+ break;
+ }
+}
+
+/** ixgbe_setup_sfp_modules_X550em - Setup SFP module
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_sfp_modules_X550em(struct ixgbe_hw *hw)
+{
+ bool setup_linear;
+ u16 reg_slice, edc_mode;
+ s32 ret_val;
+
+ switch (hw->phy.sfp_type) {
+ case ixgbe_sfp_type_unknown:
+ return 0;
+ case ixgbe_sfp_type_not_present:
+ return IXGBE_ERR_SFP_NOT_PRESENT;
+ case ixgbe_sfp_type_da_cu_core0:
+ case ixgbe_sfp_type_da_cu_core1:
+ setup_linear = true;
+ break;
+ case ixgbe_sfp_type_srlr_core0:
+ case ixgbe_sfp_type_srlr_core1:
+ case ixgbe_sfp_type_da_act_lmt_core0:
+ case ixgbe_sfp_type_da_act_lmt_core1:
+ case ixgbe_sfp_type_1g_sx_core0:
+ case ixgbe_sfp_type_1g_sx_core1:
+ setup_linear = false;
+ break;
+ default:
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+ }
+
+ ixgbe_init_mac_link_ops_X550em(hw);
+ hw->phy.ops.reset = NULL;
+
+ /* The CS4227 slice address is the base address + the port-pair reg
+ * offset. I.e. Slice 0 = 0x12B0 and slice 1 = 0x22B0.
+ */
+ reg_slice = IXGBE_CS4227_SPARE24_LSB + (hw->bus.lan_id << 12);
+
+ if (setup_linear)
+ edc_mode = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ edc_mode = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+
+ /* Configure CS4227 for connection type. */
+ ret_val = hw->phy.ops.write_i2c_combined(hw, IXGBE_CS4227, reg_slice,
+ edc_mode);
+
+ if (ret_val)
+ ret_val = hw->phy.ops.write_i2c_combined(hw, 0x80, reg_slice,
+ edc_mode);
+
+ return ret_val;
+}
+
+/** ixgbe_get_link_capabilities_x550em - Determines link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ **/
+static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
+{
+ /* SFP */
+ if (hw->phy.media_type == ixgbe_media_type_fiber) {
+ /* CS4227 SFP must not enable auto-negotiation */
+ *autoneg = false;
+
+ if (hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return 0;
+ }
+
+ /* Link capabilities are based on SFP */
+ if (hw->phy.multispeed_fiber)
+ *speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ else
+ *speed = IXGBE_LINK_SPEED_10GB_FULL;
+ } else {
+ *speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ }
+ return 0;
+}
+
+/**
+ * ixgbe_get_lasi_ext_t_x550em - Determime external Base T PHY interrupt cause
+ * @hw: pointer to hardware structure
+ * @lsc: pointer to boolean flag which indicates whether external Base T
+ * PHY interrupt is lsc
+ *
+ * Determime if external Base T PHY interrupt cause is high temperature
+ * failure alarm or link status change.
+ *
+ * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
+ * failure alarm, else return PHY access status.
+ **/
+static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc)
+{
+ u32 status;
+ u16 reg;
+
+ *lsc = false;
+
+ /* Vendor alarm triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status || !(reg & IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN))
+ return status;
+
+ /* Vendor Auto-Neg alarm triggered or Global alarm 1 triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_FLAG,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status || !(reg & (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN |
+ IXGBE_MDIO_GLOBAL_ALARM_1_INT)))
+ return status;
+
+ /* High temperature failure alarm triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_ALARM_1,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status)
+ return status;
+
+ /* If high temperature failure, then return over temp error and exit */
+ if (reg & IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL) {
+ /* power down the PHY in case the PHY FW didn't already */
+ ixgbe_set_copper_phy_power(hw, false);
+ return IXGBE_ERR_OVERTEMP;
+ }
+
+ /* Vendor alarm 2 triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+
+ if (status || !(reg & IXGBE_MDIO_GLOBAL_STD_ALM2_INT))
+ return status;
+
+ /* link connect/disconnect event occurred */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM2,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+
+ if (status)
+ return status;
+
+ /* Indicate LSC */
+ if (reg & IXGBE_MDIO_AUTO_NEG_VEN_LSC)
+ *lsc = true;
+
+ return 0;
+}
+
+/**
+ * ixgbe_enable_lasi_ext_t_x550em - Enable external Base T PHY interrupts
+ * @hw: pointer to hardware structure
+ *
+ * Enable link status change and temperature failure alarm for the external
+ * Base T PHY
+ *
+ * Returns PHY access status
+ **/
+static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ u32 status;
+ u16 reg;
+ bool lsc;
+
+ /* Clear interrupt flags */
+ status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+
+ /* Enable link status change alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg);
+ if (status)
+ return status;
+
+ /* Enables high temperature failure alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_GLOBAL_INT_HI_TEMP_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+ if (status)
+ return status;
+
+ /* Enable vendor Auto-Neg alarm and Global Interrupt Mask 1 alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN |
+ IXGBE_MDIO_GLOBAL_ALARM_1_INT);
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+ if (status)
+ return status;
+
+ /* Enable chip-wide vendor alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+
+ return status;
+}
+
+/**
+ * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt
+ * @hw: pointer to hardware structure
+ *
+ * Handle external Base T PHY interrupt. If high temperature
+ * failure alarm then return error, else if link status change
+ * then setup internal/external PHY link
+ *
+ * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
+ * failure alarm, else return PHY access status.
+ **/
+static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ struct ixgbe_phy_info *phy = &hw->phy;
+ bool lsc;
+ u32 status;
+
+ status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+ if (status)
+ return status;
+
+ if (lsc)
+ return phy->ops.setup_internal_link(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_setup_kr_speed_x550em - Configure the KR PHY for link speed.
+ * @hw: pointer to hardware structure
+ * @speed: link speed
+ *
+ * Configures the integrated KR PHY.
+ **/
+static s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed)
+{
+ s32 status;
+ u32 reg_val;
+
+ status = ixgbe_read_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status)
+ return status;
+
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+ reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_FEC_REQ |
+ IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC);
+ reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR |
+ IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX);
+
+ /* Advertise 10G support. */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR;
+
+ /* Advertise 1G support. */
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX;
+
+ /* Restart auto-negotiation. */
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
+ status = ixgbe_write_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ return status;
+}
+
/** ixgbe_setup_kx4_x550em - Configure the KX4 PHY.
* @hw: pointer to hardware structure
*
**/
static s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
{
- s32 status;
- u32 reg_val;
+ return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
+}
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
- if (status)
- return status;
+/** ixgbe_ext_phy_t_x550em_get_link - Get ext phy link status
+ * @hw: address of hardware structure
+ * @link_up: address of boolean to indicate link status
+ *
+ * Returns error code if unable to get link status.
+ **/
+static s32 ixgbe_ext_phy_t_x550em_get_link(struct ixgbe_hw *hw, bool *link_up)
+{
+ u32 ret;
+ u16 autoneg_status;
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_FEC_REQ;
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
- reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX);
+ *link_up = false;
- /* Advertise 10G support. */
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL)
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR;
+ /* read this twice back to back to indicate current status */
+ ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+ if (ret)
+ return ret;
- /* Advertise 1G support. */
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL)
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX;
+ ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+ if (ret)
+ return ret;
- /* Restart auto-negotiation. */
- reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ *link_up = !!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS);
- return status;
+ return 0;
}
-/** ixgbe_setup_internal_phy_x550em - Configure integrated KR PHY
+/** ixgbe_setup_internal_phy_t_x550em - Configure KR PHY to X557 link
* @hw: point to hardware structure
*
- * Configures the integrated KR PHY to talk to the external PHY. The base
- * driver will call this function when it gets notification via interrupt from
- * the external PHY. This function forces the internal PHY into iXFI mode at
- * the correct speed.
+ * Configures the link between the integrated KR PHY and the external X557 PHY
+ * The driver will call this function when it gets a link status change
+ * interrupt from the X557 PHY. This function configures the link speed
+ * between the PHYs to match the link speed of the BASE-T link.
*
- * A return of a non-zero value indicates an error, and the base driver should
- * not report link up.
+ * A return of a non-zero value indicates an error, and the base driver should
+ * not report link up.
**/
-static s32 ixgbe_setup_internal_phy_x550em(struct ixgbe_hw *hw)
+static s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw)
{
- s32 status;
- u16 lasi, autoneg_status, speed;
ixgbe_link_speed force_speed;
+ bool link_up;
+ u32 status;
+ u16 speed;
+
+ if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
+ return IXGBE_ERR_CONFIG;
- /* Verify that the external link status has changed */
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_XENPAK_LASI_STATUS,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &lasi);
+ /* If link is not up, then there is no setup necessary so return */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
if (status)
return status;
- /* If there was no change in link status, we can just exit */
- if (!(lasi & IXGBE_XENPAK_LASI_LINK_STATUS_ALARM))
+ if (!link_up)
return 0;
- /* we read this twice back to back to indicate current status */
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_status);
+ &speed);
if (status)
return status;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_status);
+ /* If link is not still up, then no setup is necessary so return */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
if (status)
return status;
- /* If link is not up return an error indicating treat link as down */
- if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS))
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
-
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &speed);
+ if (!link_up)
+ return 0;
/* clear everything but the speed and duplex bits */
speed &= IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK;
static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
{
struct ixgbe_phy_info *phy = &hw->phy;
+ ixgbe_link_speed speed;
s32 ret_val;
- if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP) {
+ if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
ixgbe_setup_mux_ctl(hw);
+
+ /* Save NW management interface connected on board. This is used
+ * to determine internal PHY mode.
+ */
+ phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
+
+ /* If internal PHY mode is KR, then initialize KR link */
+ if (phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE) {
+ speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ ret_val = ixgbe_setup_kr_speed_x550em(hw, speed);
+ }
}
/* Identify the PHY or SFP module */
ret_val = phy->ops.identify(hw);
- /* Setup function pointers based on detected SFP module and speeds */
+ /* Setup function pointers based on detected hardware */
ixgbe_init_mac_link_ops_X550em(hw);
if (phy->sfp_type != ixgbe_sfp_type_unknown)
phy->ops.reset = NULL;
phy->ops.write_reg = ixgbe_write_phy_reg_x550em;
break;
case ixgbe_phy_x550em_ext_t:
- phy->ops.setup_internal_link = ixgbe_setup_internal_phy_x550em;
+ /* Save NW management interface connected on board. This is used
+ * to determine internal PHY mode
+ */
+ phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
+
+ /* If internal link mode is XFI, then setup iXFI internal link,
+ * else setup KR now.
+ */
+ if (!(phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ phy->ops.setup_internal_link =
+ ixgbe_setup_internal_phy_t_x550em;
+ } else {
+ speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ ret_val = ixgbe_setup_kr_speed_x550em(hw, speed);
+ }
+
+ phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
break;
default:
break;
}
+
return ret_val;
}
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / commitdiff