dt-bindings: mt8173-mtu3: add generic compatible and rename file

The mt8173-mtu3.txt actually holds the bindings for all mediatek
SoCs with usb3 DRD IP, so add a generic compatible and change the
name to mediatek,mtu3.txt.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
new file mode 100644 (file)
index 0000000..838ae48
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
@@ -0,0 +1,91 @@
+The device node for Mediatek USB3.0 DRD controller
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
+       soc-model is the name of SoC, such as mt8173, mt2712 etc,
+       when using "mediatek,mtu3" compatible string, you need SoC specific
+       ones in addition, one of:
+       - "mediatek,mt8173-mtu3"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be "mac" for device IP and "ippc" for IP port control
+ - interrupts : interrupt used by the device IP
+ - power-domains : a phandle to USB power domain node to control USB's
+       mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+       entry in clock-names
+ - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
+       "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
+       depends on "mediatek,enable-wakeup"
+ - phys : a list of phandle + phy specifier pairs
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+       refer to usb/generic.txt
+
+Optional properties:
+ - #address-cells, #size-cells : should be '2' if the device has sub-nodes
+       with 'reg' property
+ - ranges : allows valid 1:1 translation between child's address space and
+       parent's address space
+ - extcon : external connector for vbus and idpin changes detection, needed
+       when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+       dual-role mode.
+ - pinctl-names : a pinctrl state named "default" must be defined,
+       "id_float" and "id_ground" are optinal which depends on
+       "mediatek,enable-manual-drd"
+ - pinctrl-0 : pin control group
+       See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+ - maximum-speed : valid arguments are "super-speed", "high-speed" and
+       "full-speed"; refer to usb/generic.txt
+ - enable-manual-drd : supports manual dual-role switch via debugfs; usually
+       used when receptacle is TYPE-A and also wants to support dual-role
+       mode.
+ - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+       control register, it depends on "mediatek,enable-wakeup".
+
+Sub-nodes:
+The xhci should be added as subnode to mtu3 as shown in the following example
+if host mode is enabled. The DT binding details of xhci can be found in:
+Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
+
+Example:
+ssusb: usb@11271000 {
+       compatible = "mediatek,mt8173-mtu3";
+       reg = <0 0x11271000 0 0x3000>,
+             <0 0x11280700 0 0x0100>;
+       reg-names = "mac", "ippc";
+       interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
+       phys = <&phy_port0 PHY_TYPE_USB3>,
+              <&phy_port1 PHY_TYPE_USB2>;
+       power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+       clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
+                <&pericfg CLK_PERI_USB0>,
+                <&pericfg CLK_PERI_USB1>;
+       clock-names = "sys_ck", "ref_ck",
+                     "wakeup_deb_p0",
+                     "wakeup_deb_p1";
+       vusb33-supply = <&mt6397_vusb_reg>;
+       vbus-supply = <&usb_p0_vbus>;
+       extcon = <&extcon_usb>;
+       dr_mode = "otg";
+       mediatek,enable-wakeup;
+       mediatek,syscon-wakeup = <&pericfg>;
+       #address-cells = <2>;
+       #size-cells = <2>;
+       ranges;
+       status = "disabled";
+
+       usb_host: xhci@11270000 {
+               compatible = "mediatek,mt8173-xhci";
+               reg = <0 0x11270000 0 0x1000>;
+               reg-names = "mac";
+               interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+               power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+               clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+               clock-names = "sys_ck", "ref_ck";
+               vusb33-supply = <&mt6397_vusb_reg>;
+               status = "disabled";
+       };
+};

diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
deleted file mode 100644 (file)
index b8ea394..0000000
--- a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-The device node for Mediatek USB3.0 DRD controller
-
-Required properties:
- - compatible : should be "mediatek,mt8173-mtu3"
- - reg : specifies physical base address and size of the registers
- - reg-names: should be "mac" for device IP and "ippc" for IP port control
- - interrupts : interrupt used by the device IP
- - power-domains : a phandle to USB power domain node to control USB's
-       mtcmos
- - vusb33-supply : regulator of USB avdd3.3v
- - clocks : a list of phandle + clock-specifier pairs, one for each
-       entry in clock-names
- - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
-       "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
-       depends on "mediatek,enable-wakeup"
- - phys : a list of phandle + phy specifier pairs
- - dr_mode : should be one of "host", "peripheral" or "otg",
-       refer to usb/generic.txt
-
-Optional properties:
- - #address-cells, #size-cells : should be '2' if the device has sub-nodes
-       with 'reg' property
- - ranges : allows valid 1:1 translation between child's address space and
-       parent's address space
- - extcon : external connector for vbus and idpin changes detection, needed
-       when supports dual-role mode.
- - vbus-supply : reference to the VBUS regulator, needed when supports
-       dual-role mode.
- - pinctl-names : a pinctrl state named "default" must be defined,
-       "id_float" and "id_ground" are optinal which depends on
-       "mediatek,enable-manual-drd"
- - pinctrl-0 : pin control group
-       See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
- - maximum-speed : valid arguments are "super-speed", "high-speed" and
-       "full-speed"; refer to usb/generic.txt
- - enable-manual-drd : supports manual dual-role switch via debugfs; usually
-       used when receptacle is TYPE-A and also wants to support dual-role
-       mode.
- - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
- - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
-       control register, it depends on "mediatek,enable-wakeup".
-
-Sub-nodes:
-The xhci should be added as subnode to mtu3 as shown in the following example
-if host mode is enabled. The DT binding details of xhci can be found in:
-Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
-
-Example:
-ssusb: usb@11271000 {
-       compatible = "mediatek,mt8173-mtu3";
-       reg = <0 0x11271000 0 0x3000>,
-             <0 0x11280700 0 0x0100>;
-       reg-names = "mac", "ippc";
-       interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
-       phys = <&phy_port0 PHY_TYPE_USB3>,
-              <&phy_port1 PHY_TYPE_USB2>;
-       power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
-       clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
-                <&pericfg CLK_PERI_USB0>,
-                <&pericfg CLK_PERI_USB1>;
-       clock-names = "sys_ck", "ref_ck",
-                     "wakeup_deb_p0",
-                     "wakeup_deb_p1";
-       vusb33-supply = <&mt6397_vusb_reg>;
-       vbus-supply = <&usb_p0_vbus>;
-       extcon = <&extcon_usb>;
-       dr_mode = "otg";
-       mediatek,enable-wakeup;
-       mediatek,syscon-wakeup = <&pericfg>;
-       #address-cells = <2>;
-       #size-cells = <2>;
-       ranges;
-       status = "disabled";
-
-       usb_host: xhci@11270000 {
-               compatible = "mediatek,mt8173-xhci";
-               reg = <0 0x11270000 0 0x1000>;
-               reg-names = "mac";
-               interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
-               power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
-               clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
-               clock-names = "sys_ck", "ref_ck";
-               vusb33-supply = <&mt6397_vusb_reg>;
-               status = "disabled";
-       };
-};