drm/i915: dsi: fix pipe-off timeout due to port vs. pipe disable ordering
authorImre Deak <imre.deak@intel.com>
Tue, 27 May 2014 16:00:09 +0000 (19:00 +0300)
committerDaniel Vetter <daniel.vetter@ffwll.ch>
Thu, 5 Jun 2014 06:52:33 +0000 (08:52 +0200)
If we disable first the port (by disabling DPI) and only then the
display pipe the pipe-off flag will never be set, possibly leading to a
hanged pipe state at the next modeset-enable.

Note that according to the VLV2 display cluster HAS, we should disable
the port before the pipe. This doesn't seem to match reality based on
the above and it's also asymmetric with the enabling sequence, where we
first enable the port and then the pipe.

v2:
- send the panel shutdown command before stopping the pipe, since this
  is the recommended sequence (Shobhit)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/intel_dsi.c

index 944a4211aa9147cda2f3c192bd6d11c5c7ecc842..02f99d768d49f4f76d6eb1ec9de683911d3332c5 100644 (file)
@@ -206,6 +206,19 @@ static void intel_dsi_enable_nop(struct intel_encoder *encoder)
         */
 }
 
+static void intel_dsi_pre_disable(struct intel_encoder *encoder)
+{
+       struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+
+       DRM_DEBUG_KMS("\n");
+
+       if (is_vid_mode(intel_dsi)) {
+               /* Send Shutdown command to the panel in LP mode */
+               dpi_send_cmd(intel_dsi, SHUTDOWN, DPI_LP_MODE_EN);
+               msleep(10);
+       }
+}
+
 static void intel_dsi_disable(struct intel_encoder *encoder)
 {
        struct drm_device *dev = encoder->base.dev;
@@ -218,10 +231,6 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
        DRM_DEBUG_KMS("\n");
 
        if (is_vid_mode(intel_dsi)) {
-               /* Send Shutdown command to the panel in LP mode */
-               dpi_send_cmd(intel_dsi, SHUTDOWN, DPI_LP_MODE_EN);
-               msleep(10);
-
                /* de-assert ip_tg_enable signal */
                temp = I915_READ(MIPI_PORT_CTRL(pipe));
                I915_WRITE(MIPI_PORT_CTRL(pipe), temp & ~DPI_ENABLE);
@@ -293,6 +302,8 @@ static void intel_dsi_post_disable(struct intel_encoder *encoder)
 
        DRM_DEBUG_KMS("\n");
 
+       intel_dsi_disable(encoder);
+
        intel_dsi_clear_device_ready(encoder);
 
        val = I915_READ(DSPCLK_GATE_D);
@@ -695,7 +706,7 @@ bool intel_dsi_init(struct drm_device *dev)
        intel_encoder->pre_pll_enable = intel_dsi_pre_pll_enable;
        intel_encoder->pre_enable = intel_dsi_pre_enable;
        intel_encoder->enable = intel_dsi_enable_nop;
-       intel_encoder->disable = intel_dsi_disable;
+       intel_encoder->disable = intel_dsi_pre_disable;
        intel_encoder->post_disable = intel_dsi_post_disable;
        intel_encoder->get_hw_state = intel_dsi_get_hw_state;
        intel_encoder->get_config = intel_dsi_get_config;