#include "bnx2x_reg.h"
#include "bnx2x_fw_defs.h"
#include "bnx2x_hsi.h"
+#include "bnx2x_link.h"
#include "bnx2x.h"
#include "bnx2x_init.h"
REG_WR(bp, dmae_reg_go_c[idx], 1);
}
-static void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr,
+void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr,
u32 dst_addr, u32 len32)
{
struct dmae_command *dmae = &bp->dmae;
}
}
-#ifdef BNX2X_DMAE_RD
-static void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32)
+void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32)
{
struct dmae_command *dmae = &bp->dmae;
int port = bp->port;
bp->slowpath->wb_data[2], bp->slowpath->wb_data[3]);
*/
}
-#endif
static int bnx2x_mc_assert(struct bnx2x *bp)
{
return IRQ_HANDLED;
}
-/* end of fast path */
-
-/* PHY/MAC */
-
-/*
- * General service functions
- */
-
-static void bnx2x_leds_set(struct bnx2x *bp, unsigned int speed)
-{
- int port = bp->port;
-
- NIG_WR(NIG_REG_LED_MODE_P0 + port*4,
- ((bp->hw_config & SHARED_HW_CFG_LED_MODE_MASK) >>
- SHARED_HW_CFG_LED_MODE_SHIFT));
- NIG_WR(NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0);
-
- /* Set blinking rate to ~15.9Hz */
- NIG_WR(NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4,
- LED_BLINK_RATE_VAL);
- NIG_WR(NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + port*4, 1);
-
- /* On Ax chip versions for speeds less than 10G
- LED scheme is different */
- if ((CHIP_REV(bp) == CHIP_REV_Ax) && (speed < SPEED_10000)) {
- NIG_WR(NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 1);
- NIG_WR(NIG_REG_LED_CONTROL_TRAFFIC_P0 + port*4, 0);
- NIG_WR(NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 + port*4, 1);
- }
-}
-
-static void bnx2x_leds_unset(struct bnx2x *bp)
-{
- int port = bp->port;
-
- NIG_WR(NIG_REG_LED_10G_P0 + port*4, 0);
- NIG_WR(NIG_REG_LED_MODE_P0 + port*4, SHARED_HW_CFG_LED_MAC1);
-}
-
-static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits)
-{
- u32 val = REG_RD(bp, reg);
-
- val |= bits;
- REG_WR(bp, reg, val);
- return val;
-}
-
-static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits)
-{
- u32 val = REG_RD(bp, reg);
-
- val &= ~bits;
- REG_WR(bp, reg, val);
- return val;
-}
-
-static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource)
-{
- u32 cnt;
- u32 lock_status;
- u32 resource_bit = (1 << resource);
- u8 func = bp->port;
-
- /* Validating that the resource is within range */
- if (resource > HW_LOCK_MAX_RESOURCE_VALUE) {
- DP(NETIF_MSG_HW,
- "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n",
- resource, HW_LOCK_MAX_RESOURCE_VALUE);
- return -EINVAL;
- }
-
- /* Validating that the resource is not already taken */
- lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + func*8);
- if (lock_status & resource_bit) {
- DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n",
- lock_status, resource_bit);
- return -EEXIST;
- }
-
- /* Try for 1 second every 5ms */
- for (cnt = 0; cnt < 200; cnt++) {
- /* Try to acquire the lock */
- REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + func*8 + 4,
- resource_bit);
- lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + func*8);
- if (lock_status & resource_bit)
- return 0;
-
- msleep(5);
- }
- DP(NETIF_MSG_HW, "Timeout\n");
- return -EAGAIN;
-}
-
-static int bnx2x_hw_unlock(struct bnx2x *bp, u32 resource)
-{
- u32 lock_status;
- u32 resource_bit = (1 << resource);
- u8 func = bp->port;
-
- /* Validating that the resource is within range */
- if (resource > HW_LOCK_MAX_RESOURCE_VALUE) {
- DP(NETIF_MSG_HW,
- "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n",
- resource, HW_LOCK_MAX_RESOURCE_VALUE);
- return -EINVAL;
- }
-
- /* Validating that the resource is currently taken */
- lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + func*8);
- if (!(lock_status & resource_bit)) {
- DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n",
- lock_status, resource_bit);
- return -EFAULT;
- }
-
- REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + func*8, resource_bit);
- return 0;
-}
-
-static int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode)
-{
- /* The GPIO should be swapped if swap register is set and active */
- int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) &&
- REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ bp->port;
- int gpio_shift = gpio_num +
- (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0);
- u32 gpio_mask = (1 << gpio_shift);
- u32 gpio_reg;
-
- if (gpio_num > MISC_REGISTERS_GPIO_3) {
- BNX2X_ERR("Invalid GPIO %d\n", gpio_num);
- return -EINVAL;
- }
-
- bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
- /* read GPIO and mask except the float bits */
- gpio_reg = (REG_RD(bp, MISC_REG_GPIO) & MISC_REGISTERS_GPIO_FLOAT);
-
- switch (mode) {
- case MISC_REGISTERS_GPIO_OUTPUT_LOW:
- DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output low\n",
- gpio_num, gpio_shift);
- /* clear FLOAT and set CLR */
- gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
- gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_CLR_POS);
- break;
-
- case MISC_REGISTERS_GPIO_OUTPUT_HIGH:
- DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output high\n",
- gpio_num, gpio_shift);
- /* clear FLOAT and set SET */
- gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
- gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_SET_POS);
- break;
-
- case MISC_REGISTERS_GPIO_INPUT_HI_Z :
- DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> input\n",
- gpio_num, gpio_shift);
- /* set FLOAT */
- gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
- break;
-
- default:
- break;
- }
-
- REG_WR(bp, MISC_REG_GPIO, gpio_reg);
- bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_GPIO);
-
- return 0;
-}
-
-static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode)
-{
- u32 spio_mask = (1 << spio_num);
- u32 spio_reg;
-
- if ((spio_num < MISC_REGISTERS_SPIO_4) ||
- (spio_num > MISC_REGISTERS_SPIO_7)) {
- BNX2X_ERR("Invalid SPIO %d\n", spio_num);
- return -EINVAL;
- }
-
- bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_SPIO);
- /* read SPIO and mask except the float bits */
- spio_reg = (REG_RD(bp, MISC_REG_SPIO) & MISC_REGISTERS_SPIO_FLOAT);
-
- switch (mode) {
- case MISC_REGISTERS_SPIO_OUTPUT_LOW :
- DP(NETIF_MSG_LINK, "Set SPIO %d -> output low\n", spio_num);
- /* clear FLOAT and set CLR */
- spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
- spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_CLR_POS);
- break;
-
- case MISC_REGISTERS_SPIO_OUTPUT_HIGH :
- DP(NETIF_MSG_LINK, "Set SPIO %d -> output high\n", spio_num);
- /* clear FLOAT and set SET */
- spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
- spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_SET_POS);
- break;
-
- case MISC_REGISTERS_SPIO_INPUT_HI_Z:
- DP(NETIF_MSG_LINK, "Set SPIO %d -> input\n", spio_num);
- /* set FLOAT */
- spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
- break;
-
- default:
- break;
- }
-
- REG_WR(bp, MISC_REG_SPIO, spio_reg);
- bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_SPIO);
-
- return 0;
-}
-
-static int bnx2x_mdio22_write(struct bnx2x *bp, u32 reg, u32 val)
-{
- int port = bp->port;
- u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
- u32 tmp;
- int i, rc;
-
-/* DP(NETIF_MSG_HW, "phy_addr 0x%x reg 0x%x val 0x%08x\n",
- bp->phy_addr, reg, val); */
-
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG) {
-
- tmp = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- tmp &= ~EMAC_MDIO_MODE_AUTO_POLL;
- EMAC_WR(EMAC_REG_EMAC_MDIO_MODE, tmp);
- REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- udelay(40);
- }
-
- tmp = ((bp->phy_addr << 21) | (reg << 16) |
- (val & EMAC_MDIO_COMM_DATA) |
- EMAC_MDIO_COMM_COMMAND_WRITE_22 |
- EMAC_MDIO_COMM_START_BUSY);
- EMAC_WR(EMAC_REG_EMAC_MDIO_COMM, tmp);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- tmp = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM);
- if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
- udelay(5);
- break;
- }
- }
-
- if (tmp & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("write phy register failed\n");
-
- rc = -EBUSY;
- } else {
- rc = 0;
- }
-
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG) {
-
- tmp = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- tmp |= EMAC_MDIO_MODE_AUTO_POLL;
- EMAC_WR(EMAC_REG_EMAC_MDIO_MODE, tmp);
- }
-
- return rc;
-}
-
-static int bnx2x_mdio22_read(struct bnx2x *bp, u32 reg, u32 *ret_val)
-{
- int port = bp->port;
- u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
- u32 val;
- int i, rc;
-
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG) {
-
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- val &= ~EMAC_MDIO_MODE_AUTO_POLL;
- EMAC_WR(EMAC_REG_EMAC_MDIO_MODE, val);
- REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- udelay(40);
- }
-
- val = ((bp->phy_addr << 21) | (reg << 16) |
- EMAC_MDIO_COMM_COMMAND_READ_22 |
- EMAC_MDIO_COMM_START_BUSY);
- EMAC_WR(EMAC_REG_EMAC_MDIO_COMM, val);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM);
- if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
- val &= EMAC_MDIO_COMM_DATA;
- break;
- }
- }
-
- if (val & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("read phy register failed\n");
-
- *ret_val = 0x0;
- rc = -EBUSY;
- } else {
- *ret_val = val;
- rc = 0;
- }
-
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG) {
-
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
- val |= EMAC_MDIO_MODE_AUTO_POLL;
- EMAC_WR(EMAC_REG_EMAC_MDIO_MODE, val);
- }
-
-/* DP(NETIF_MSG_HW, "phy_addr 0x%x reg 0x%x ret_val 0x%08x\n",
- bp->phy_addr, reg, *ret_val); */
-
- return rc;
-}
-
-static int bnx2x_mdio45_ctrl_write(struct bnx2x *bp, u32 mdio_ctrl,
- u32 phy_addr, u32 reg, u32 addr, u32 val)
-{
- u32 tmp;
- int i, rc = 0;
-
- /* set clause 45 mode, slow down the MDIO clock to 2.5MHz
- * (a value of 49==0x31) and make sure that the AUTO poll is off
- */
- tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- tmp &= ~(EMAC_MDIO_MODE_AUTO_POLL | EMAC_MDIO_MODE_CLOCK_CNT);
- tmp |= (EMAC_MDIO_MODE_CLAUSE_45 |
- (49 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, tmp);
- REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- udelay(40);
-
- /* address */
- tmp = ((phy_addr << 21) | (reg << 16) | addr |
- EMAC_MDIO_COMM_COMMAND_ADDRESS |
- EMAC_MDIO_COMM_START_BUSY);
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
- if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
- udelay(5);
- break;
- }
- }
- if (tmp & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("write phy register failed\n");
-
- rc = -EBUSY;
-
- } else {
- /* data */
- tmp = ((phy_addr << 21) | (reg << 16) | val |
- EMAC_MDIO_COMM_COMMAND_WRITE_45 |
- EMAC_MDIO_COMM_START_BUSY);
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
- if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
- udelay(5);
- break;
- }
- }
-
- if (tmp & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("write phy register failed\n");
-
- rc = -EBUSY;
- }
- }
-
- /* unset clause 45 mode, set the MDIO clock to a faster value
- * (0x13 => 6.25Mhz) and restore the AUTO poll if needed
- */
- tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- tmp &= ~(EMAC_MDIO_MODE_CLAUSE_45 | EMAC_MDIO_MODE_CLOCK_CNT);
- tmp |= (0x13 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG)
- tmp |= EMAC_MDIO_MODE_AUTO_POLL;
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, tmp);
-
- return rc;
-}
-
-static int bnx2x_mdio45_write(struct bnx2x *bp, u32 phy_addr, u32 reg,
- u32 addr, u32 val)
-{
- u32 emac_base = bp->port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
-
- return bnx2x_mdio45_ctrl_write(bp, emac_base, phy_addr,
- reg, addr, val);
-}
-
-static int bnx2x_mdio45_ctrl_read(struct bnx2x *bp, u32 mdio_ctrl,
- u32 phy_addr, u32 reg, u32 addr,
- u32 *ret_val)
-{
- u32 val;
- int i, rc = 0;
-
- /* set clause 45 mode, slow down the MDIO clock to 2.5MHz
- * (a value of 49==0x31) and make sure that the AUTO poll is off
- */
- val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- val &= ~(EMAC_MDIO_MODE_AUTO_POLL | EMAC_MDIO_MODE_CLOCK_CNT);
- val |= (EMAC_MDIO_MODE_CLAUSE_45 |
- (49 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val);
- REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- udelay(40);
-
- /* address */
- val = ((phy_addr << 21) | (reg << 16) | addr |
- EMAC_MDIO_COMM_COMMAND_ADDRESS |
- EMAC_MDIO_COMM_START_BUSY);
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
- if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
- udelay(5);
- break;
- }
- }
- if (val & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("read phy register failed\n");
-
- *ret_val = 0;
- rc = -EBUSY;
-
- } else {
- /* data */
- val = ((phy_addr << 21) | (reg << 16) |
- EMAC_MDIO_COMM_COMMAND_READ_45 |
- EMAC_MDIO_COMM_START_BUSY);
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
-
- for (i = 0; i < 50; i++) {
- udelay(10);
-
- val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
- if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
- val &= EMAC_MDIO_COMM_DATA;
- break;
- }
- }
-
- if (val & EMAC_MDIO_COMM_START_BUSY) {
- BNX2X_ERR("read phy register failed\n");
-
- val = 0;
- rc = -EBUSY;
- }
-
- *ret_val = val;
- }
-
- /* unset clause 45 mode, set the MDIO clock to a faster value
- * (0x13 => 6.25Mhz) and restore the AUTO poll if needed
- */
- val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
- val &= ~(EMAC_MDIO_MODE_CLAUSE_45 | EMAC_MDIO_MODE_CLOCK_CNT);
- val |= (0x13 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
- if (bp->phy_flags & PHY_INT_MODE_AUTO_POLLING_FLAG)
- val |= EMAC_MDIO_MODE_AUTO_POLL;
- REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val);
-
- return rc;
-}
-
-static int bnx2x_mdio45_read(struct bnx2x *bp, u32 phy_addr, u32 reg,
- u32 addr, u32 *ret_val)
-{
- u32 emac_base = bp->port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
-
- return bnx2x_mdio45_ctrl_read(bp, emac_base, phy_addr,
- reg, addr, ret_val);
-}
-
-static int bnx2x_mdio45_vwrite(struct bnx2x *bp, u32 phy_addr, u32 reg,
- u32 addr, u32 val)
-{
- int i;
- u32 rd_val;
-
- might_sleep();
- for (i = 0; i < 10; i++) {
- bnx2x_mdio45_write(bp, phy_addr, reg, addr, val);
- msleep(5);
- bnx2x_mdio45_read(bp, phy_addr, reg, addr, &rd_val);
- /* if the read value is not the same as the value we wrote,
- we should write it again */
- if (rd_val == val)
- return 0;
- }
- BNX2X_ERR("MDIO write in CL45 failed\n");
- return -EBUSY;
-}
-
-/*
- * link management
- */
-
-static void bnx2x_pause_resolve(struct bnx2x *bp, u32 pause_result)
-{
- switch (pause_result) { /* ASYM P ASYM P */
- case 0xb: /* 1 0 1 1 */
- bp->flow_ctrl = FLOW_CTRL_TX;
- break;
-
- case 0xe: /* 1 1 1 0 */
- bp->flow_ctrl = FLOW_CTRL_RX;
- break;
-
- case 0x5: /* 0 1 0 1 */
- case 0x7: /* 0 1 1 1 */
- case 0xd: /* 1 1 0 1 */
- case 0xf: /* 1 1 1 1 */
- bp->flow_ctrl = FLOW_CTRL_BOTH;
- break;
-
- default:
- break;
- }
-}
-
-static u8 bnx2x_ext_phy_resove_fc(struct bnx2x *bp)
-{
- u32 ext_phy_addr;
- u32 ld_pause; /* local */
- u32 lp_pause; /* link partner */
- u32 an_complete; /* AN complete */
- u32 pause_result;
- u8 ret = 0;
-
- ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
-
- /* read twice */
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_STATUS, &an_complete);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_STATUS, &an_complete);
-
- if (an_complete & EXT_PHY_KR_AUTO_NEG_COMPLETE) {
- ret = 1;
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_AUTO_NEG_ADVERT, &ld_pause);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_LP_AUTO_NEG, &lp_pause);
- pause_result = (ld_pause &
- EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_MASK) >> 8;
- pause_result |= (lp_pause &
- EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_MASK) >> 10;
- DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x \n",
- pause_result);
- bnx2x_pause_resolve(bp, pause_result);
- }
- return ret;
-}
-
-static void bnx2x_flow_ctrl_resolve(struct bnx2x *bp, u32 gp_status)
-{
- u32 ld_pause; /* local driver */
- u32 lp_pause; /* link partner */
- u32 pause_result;
-
- bp->flow_ctrl = 0;
-
- /* resolve from gp_status in case of AN complete and not sgmii */
- if ((bp->req_autoneg & AUTONEG_FLOW_CTRL) &&
- (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) &&
- (!(bp->phy_flags & PHY_SGMII_FLAG)) &&
- (XGXS_EXT_PHY_TYPE(bp) == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)) {
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
- &ld_pause);
- bnx2x_mdio22_read(bp,
- MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
- &lp_pause);
- pause_result = (ld_pause &
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5;
- pause_result |= (lp_pause &
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
- DP(NETIF_MSG_LINK, "pause_result 0x%x\n", pause_result);
- bnx2x_pause_resolve(bp, pause_result);
- } else if (!(bp->req_autoneg & AUTONEG_FLOW_CTRL) ||
- !(bnx2x_ext_phy_resove_fc(bp))) {
- /* forced speed */
- if (bp->req_autoneg & AUTONEG_FLOW_CTRL) {
- switch (bp->req_flow_ctrl) {
- case FLOW_CTRL_AUTO:
- if (bp->dev->mtu <= 4500)
- bp->flow_ctrl = FLOW_CTRL_BOTH;
- else
- bp->flow_ctrl = FLOW_CTRL_TX;
- break;
-
- case FLOW_CTRL_TX:
- bp->flow_ctrl = FLOW_CTRL_TX;
- break;
-
- case FLOW_CTRL_RX:
- if (bp->dev->mtu <= 4500)
- bp->flow_ctrl = FLOW_CTRL_RX;
- break;
-
- case FLOW_CTRL_BOTH:
- if (bp->dev->mtu <= 4500)
- bp->flow_ctrl = FLOW_CTRL_BOTH;
- else
- bp->flow_ctrl = FLOW_CTRL_TX;
- break;
-
- case FLOW_CTRL_NONE:
- default:
- break;
- }
- } else { /* forced mode */
- switch (bp->req_flow_ctrl) {
- case FLOW_CTRL_AUTO:
- DP(NETIF_MSG_LINK, "req_flow_ctrl 0x%x while"
- " req_autoneg 0x%x\n",
- bp->req_flow_ctrl, bp->req_autoneg);
- break;
-
- case FLOW_CTRL_TX:
- case FLOW_CTRL_RX:
- case FLOW_CTRL_BOTH:
- bp->flow_ctrl = bp->req_flow_ctrl;
- break;
-
- case FLOW_CTRL_NONE:
- default:
- break;
- }
- }
- }
- DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", bp->flow_ctrl);
-}
-
-static void bnx2x_link_settings_status(struct bnx2x *bp, u32 gp_status)
-{
- bp->link_status = 0;
-
- if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
- DP(NETIF_MSG_LINK, "phy link up\n");
-
- bp->phy_link_up = 1;
- bp->link_status |= LINK_STATUS_LINK_UP;
-
- if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS)
- bp->duplex = DUPLEX_FULL;
- else
- bp->duplex = DUPLEX_HALF;
-
- bnx2x_flow_ctrl_resolve(bp, gp_status);
-
- switch (gp_status & GP_STATUS_SPEED_MASK) {
- case GP_STATUS_10M:
- bp->line_speed = SPEED_10;
- if (bp->duplex == DUPLEX_FULL)
- bp->link_status |= LINK_10TFD;
- else
- bp->link_status |= LINK_10THD;
- break;
-
- case GP_STATUS_100M:
- bp->line_speed = SPEED_100;
- if (bp->duplex == DUPLEX_FULL)
- bp->link_status |= LINK_100TXFD;
- else
- bp->link_status |= LINK_100TXHD;
- break;
-
- case GP_STATUS_1G:
- case GP_STATUS_1G_KX:
- bp->line_speed = SPEED_1000;
- if (bp->duplex == DUPLEX_FULL)
- bp->link_status |= LINK_1000TFD;
- else
- bp->link_status |= LINK_1000THD;
- break;
-
- case GP_STATUS_2_5G:
- bp->line_speed = SPEED_2500;
- if (bp->duplex == DUPLEX_FULL)
- bp->link_status |= LINK_2500TFD;
- else
- bp->link_status |= LINK_2500THD;
- break;
-
- case GP_STATUS_5G:
- case GP_STATUS_6G:
- BNX2X_ERR("link speed unsupported gp_status 0x%x\n",
- gp_status);
- break;
-
- case GP_STATUS_10G_KX4:
- case GP_STATUS_10G_HIG:
- case GP_STATUS_10G_CX4:
- bp->line_speed = SPEED_10000;
- bp->link_status |= LINK_10GTFD;
- break;
-
- case GP_STATUS_12G_HIG:
- bp->line_speed = SPEED_12000;
- bp->link_status |= LINK_12GTFD;
- break;
-
- case GP_STATUS_12_5G:
- bp->line_speed = SPEED_12500;
- bp->link_status |= LINK_12_5GTFD;
- break;
-
- case GP_STATUS_13G:
- bp->line_speed = SPEED_13000;
- bp->link_status |= LINK_13GTFD;
- break;
-
- case GP_STATUS_15G:
- bp->line_speed = SPEED_15000;
- bp->link_status |= LINK_15GTFD;
- break;
-
- case GP_STATUS_16G:
- bp->line_speed = SPEED_16000;
- bp->link_status |= LINK_16GTFD;
- break;
-
- default:
- BNX2X_ERR("link speed unsupported gp_status 0x%x\n",
- gp_status);
- break;
- }
-
- bp->link_status |= LINK_STATUS_SERDES_LINK;
-
- if (bp->req_autoneg & AUTONEG_SPEED) {
- bp->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED;
-
- if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE)
- bp->link_status |=
- LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
-
- if (bp->autoneg & AUTONEG_PARALLEL)
- bp->link_status |=
- LINK_STATUS_PARALLEL_DETECTION_USED;
- }
-
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- bp->link_status |= LINK_STATUS_TX_FLOW_CONTROL_ENABLED;
-
- if (bp->flow_ctrl & FLOW_CTRL_RX)
- bp->link_status |= LINK_STATUS_RX_FLOW_CONTROL_ENABLED;
-
- } else { /* link_down */
- DP(NETIF_MSG_LINK, "phy link down\n");
-
- bp->phy_link_up = 0;
-
- bp->line_speed = 0;
- bp->duplex = DUPLEX_FULL;
- bp->flow_ctrl = 0;
- }
-
- DP(NETIF_MSG_LINK, "gp_status 0x%x phy_link_up %d\n"
- DP_LEVEL " line_speed %d duplex %d flow_ctrl 0x%x"
- " link_status 0x%x\n",
- gp_status, bp->phy_link_up, bp->line_speed, bp->duplex,
- bp->flow_ctrl, bp->link_status);
-}
-
-static void bnx2x_link_int_ack(struct bnx2x *bp, int is_10g)
-{
- int port = bp->port;
-
- /* first reset all status
- * we assume only one line will be change at a time */
- bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- (NIG_STATUS_XGXS0_LINK10G |
- NIG_STATUS_XGXS0_LINK_STATUS |
- NIG_STATUS_SERDES0_LINK_STATUS));
- if (bp->phy_link_up) {
- if (is_10g) {
- /* Disable the 10G link interrupt
- * by writing 1 to the status register
- */
- DP(NETIF_MSG_LINK, "10G XGXS phy link up\n");
- bnx2x_bits_en(bp,
- NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- NIG_STATUS_XGXS0_LINK10G);
-
- } else if (bp->phy_flags & PHY_XGXS_FLAG) {
- /* Disable the link interrupt
- * by writing 1 to the relevant lane
- * in the status register
- */
- DP(NETIF_MSG_LINK, "1G XGXS phy link up\n");
- bnx2x_bits_en(bp,
- NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- ((1 << bp->ser_lane) <<
- NIG_STATUS_XGXS0_LINK_STATUS_SIZE));
-
- } else { /* SerDes */
- DP(NETIF_MSG_LINK, "SerDes phy link up\n");
- /* Disable the link interrupt
- * by writing 1 to the status register
- */
- bnx2x_bits_en(bp,
- NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- NIG_STATUS_SERDES0_LINK_STATUS);
- }
-
- } else { /* link_down */
- }
-}
-
-static int bnx2x_ext_phy_is_link_up(struct bnx2x *bp)
-{
- u32 ext_phy_type;
- u32 ext_phy_addr;
- u32 val1 = 0, val2;
- u32 rx_sd, pcs_status;
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
-
- ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
- switch (ext_phy_type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "XGXS Direct\n");
- val1 = 1;
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- DP(NETIF_MSG_LINK, "XGXS 8705\n");
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_WIS_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
-
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_WIS_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
-
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_PMD_RX_SD, &rx_sd);
- DP(NETIF_MSG_LINK, "8705 rx_sd 0x%x\n", rx_sd);
- val1 = (rx_sd & 0x1);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- DP(NETIF_MSG_LINK, "XGXS 8706\n");
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK, "8706 LASI status 0x%x\n", val1);
-
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK, "8706 LASI status 0x%x\n", val1);
-
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_PMD_RX_SD, &rx_sd);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PCS_DEVAD,
- EXT_PHY_OPT_PCS_STATUS, &pcs_status);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_AN_LINK_STATUS, &val2);
-
- DP(NETIF_MSG_LINK, "8706 rx_sd 0x%x"
- " pcs_status 0x%x 1Gbps link_status 0x%x 0x%x\n",
- rx_sd, pcs_status, val2, (val2 & (1<<1)));
- /* link is up if both bit 0 of pmd_rx_sd and
- * bit 0 of pcs_status are set, or if the autoneg bit
- 1 is set
- */
- val1 = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1)));
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO);
-
- /* clear the interrupt LASI status register */
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PCS_DEVAD,
- EXT_PHY_KR_LASI_STATUS, &val2);
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PCS_DEVAD,
- EXT_PHY_KR_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK, "KR LASI status 0x%x->0x%x\n",
- val2, val1);
- /* Check the LASI */
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0x9003, &val2);
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0x9003, &val1);
- DP(NETIF_MSG_LINK, "KR 0x9003 0x%x->0x%x\n",
- val2, val1);
- /* Check the link status */
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PCS_DEVAD,
- EXT_PHY_KR_PCS_STATUS, &val2);
- DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2);
- /* Check the link status on 1.1.2 */
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_KR_STATUS, &val2);
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_KR_STATUS, &val1);
- DP(NETIF_MSG_LINK,
- "KR PMA status 0x%x->0x%x\n", val2, val1);
- val1 = ((val1 & 4) == 4);
- /* If 1G was requested assume the link is up */
- if (!(bp->req_autoneg & AUTONEG_SPEED) &&
- (bp->req_line_speed == SPEED_1000))
- val1 = 1;
- bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val2);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_STATUS, &val1);
- DP(NETIF_MSG_LINK,
- "10G-base-T LASI status 0x%x->0x%x\n", val2, val1);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_KR_STATUS, &val2);
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_KR_STATUS, &val1);
- DP(NETIF_MSG_LINK,
- "10G-base-T PMA status 0x%x->0x%x\n", val2, val1);
- val1 = ((val1 & 4) == 4);
- /* if link is up
- * print the AN outcome of the SFX7101 PHY
- */
- if (val1) {
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- 0x21, &val2);
- DP(NETIF_MSG_LINK,
- "SFX7101 AN status 0x%x->%s\n", val2,
- (val2 & (1<<14)) ? "Master" : "Slave");
- }
- break;
-
- default:
- DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- val1 = 0;
- break;
- }
-
- } else { /* SerDes */
- ext_phy_type = SERDES_EXT_PHY_TYPE(bp);
- switch (ext_phy_type) {
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "SerDes Direct\n");
- val1 = 1;
- break;
-
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
- DP(NETIF_MSG_LINK, "SerDes 5482\n");
- val1 = 1;
- break;
-
- default:
- DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- val1 = 0;
- break;
- }
- }
-
- return val1;
-}
-
-static void bnx2x_bmac_enable(struct bnx2x *bp, int is_lb)
-{
- int port = bp->port;
- u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
- NIG_REG_INGRESS_BMAC0_MEM;
- u32 wb_write[2];
- u32 val;
-
- DP(NETIF_MSG_LINK, "enabling BigMAC\n");
- /* reset and unreset the BigMac */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
- msleep(5);
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
-
- /* enable access for bmac registers */
- NIG_WR(NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
-
- /* XGXS control */
- wb_write[0] = 0x3c;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
- wb_write, 2);
-
- /* tx MAC SA */
- wb_write[0] = ((bp->dev->dev_addr[2] << 24) |
- (bp->dev->dev_addr[3] << 16) |
- (bp->dev->dev_addr[4] << 8) |
- bp->dev->dev_addr[5]);
- wb_write[1] = ((bp->dev->dev_addr[0] << 8) |
- bp->dev->dev_addr[1]);
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR,
- wb_write, 2);
-
- /* tx control */
- val = 0xc0;
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- val |= 0x800000;
- wb_write[0] = val;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL, wb_write, 2);
-
- /* set tx mtu */
- wb_write[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; /* -CRC */
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_write, 2);
-
- /* mac control */
- val = 0x3;
- if (is_lb) {
- val |= 0x4;
- DP(NETIF_MSG_LINK, "enable bmac loopback\n");
- }
- wb_write[0] = val;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
- wb_write, 2);
-
- /* rx control set to don't strip crc */
- val = 0x14;
- if (bp->flow_ctrl & FLOW_CTRL_RX)
- val |= 0x20;
- wb_write[0] = val;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, wb_write, 2);
-
- /* set rx mtu */
- wb_write[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_write, 2);
-
- /* set cnt max size */
- wb_write[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; /* -VLAN */
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE,
- wb_write, 2);
-
- /* configure safc */
- wb_write[0] = 0x1000200;
- wb_write[1] = 0;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
- wb_write, 2);
-
- /* fix for emulation */
- if (CHIP_REV(bp) == CHIP_REV_EMUL) {
- wb_write[0] = 0xf000;
- wb_write[1] = 0;
- REG_WR_DMAE(bp,
- bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD,
- wb_write, 2);
- }
-
- /* reset old bmac stats */
- memset(&bp->old_bmac, 0, sizeof(struct bmac_stats));
-
- NIG_WR(NIG_REG_XCM0_OUT_EN + port*4, 0x0);
-
- /* select XGXS */
- NIG_WR(NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1);
- NIG_WR(NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0);
-
- /* disable the NIG in/out to the emac */
- NIG_WR(NIG_REG_EMAC0_IN_EN + port*4, 0x0);
- NIG_WR(NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0);
- NIG_WR(NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0);
-
- /* enable the NIG in/out to the bmac */
- NIG_WR(NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0);
-
- NIG_WR(NIG_REG_BMAC0_IN_EN + port*4, 0x1);
- val = 0;
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- val = 1;
- NIG_WR(NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val);
- NIG_WR(NIG_REG_BMAC0_OUT_EN + port*4, 0x1);
-
- bp->phy_flags |= PHY_BMAC_FLAG;
-
- bp->stats_state = STATS_STATE_ENABLE;
-}
-
-static void bnx2x_bmac_rx_disable(struct bnx2x *bp)
-{
- int port = bp->port;
- u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
- NIG_REG_INGRESS_BMAC0_MEM;
- u32 wb_write[2];
-
- /* Only if the bmac is out of reset */
- if (REG_RD(bp, MISC_REG_RESET_REG_2) &
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)) {
- /* Clear Rx Enable bit in BMAC_CONTROL register */
-#ifdef BNX2X_DMAE_RD
- bnx2x_read_dmae(bp, bmac_addr +
- BIGMAC_REGISTER_BMAC_CONTROL, 2);
- wb_write[0] = *bnx2x_sp(bp, wb_data[0]);
- wb_write[1] = *bnx2x_sp(bp, wb_data[1]);
-#else
- wb_write[0] = REG_RD(bp,
- bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL);
- wb_write[1] = REG_RD(bp,
- bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL + 4);
-#endif
- wb_write[0] &= ~BMAC_CONTROL_RX_ENABLE;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
- wb_write, 2);
- msleep(1);
- }
-}
-
-static void bnx2x_emac_enable(struct bnx2x *bp)
-{
- int port = bp->port;
- u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
- u32 val;
- int timeout;
-
- DP(NETIF_MSG_LINK, "enabling EMAC\n");
- /* reset and unreset the emac core */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
- msleep(5);
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
-
- /* enable emac and not bmac */
- NIG_WR(NIG_REG_EGRESS_EMAC0_PORT + port*4, 1);
-
- /* for paladium */
- if (CHIP_REV(bp) == CHIP_REV_EMUL) {
- /* Use lane 1 (of lanes 0-3) */
- NIG_WR(NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
- NIG_WR(NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
- }
- /* for fpga */
- else if (CHIP_REV(bp) == CHIP_REV_FPGA) {
- /* Use lane 1 (of lanes 0-3) */
- NIG_WR(NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
- NIG_WR(NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
- }
- /* ASIC */
- else {
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- DP(NETIF_MSG_LINK, "XGXS\n");
- /* select the master lanes (out of 0-3) */
- NIG_WR(NIG_REG_XGXS_LANE_SEL_P0 + port*4,
- bp->ser_lane);
- /* select XGXS */
- NIG_WR(NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
-
- } else { /* SerDes */
- DP(NETIF_MSG_LINK, "SerDes\n");
- /* select SerDes */
- NIG_WR(NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
- }
- }
-
- /* enable emac */
- NIG_WR(NIG_REG_NIG_EMAC0_EN + port*4, 1);
-
- /* init emac - use read-modify-write */
- /* self clear reset */
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- EMAC_WR(EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET));
-
- timeout = 200;
- while (val & EMAC_MODE_RESET) {
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val);
- if (!timeout) {
- BNX2X_ERR("EMAC timeout!\n");
- break;
- }
- timeout--;
- }
-
- /* reset tx part */
- EMAC_WR(EMAC_REG_EMAC_TX_MODE, EMAC_TX_MODE_RESET);
-
- timeout = 200;
- while (val & EMAC_TX_MODE_RESET) {
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_TX_MODE);
- DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val);
- if (!timeout) {
- BNX2X_ERR("EMAC timeout!\n");
- break;
- }
- timeout--;
- }
-
- if (CHIP_REV_IS_SLOW(bp)) {
- /* config GMII mode */
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- EMAC_WR(EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII));
-
- } else { /* ASIC */
- /* pause enable/disable */
- bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
- EMAC_RX_MODE_FLOW_EN);
- if (bp->flow_ctrl & FLOW_CTRL_RX)
- bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
- EMAC_RX_MODE_FLOW_EN);
-
- bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
- EMAC_TX_MODE_EXT_PAUSE_EN);
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
- EMAC_TX_MODE_EXT_PAUSE_EN);
- }
-
- /* KEEP_VLAN_TAG, promiscuous */
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE);
- val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS;
- EMAC_WR(EMAC_REG_EMAC_RX_MODE, val);
-
- /* identify magic packets */
- val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
- EMAC_WR(EMAC_REG_EMAC_MODE, (val | EMAC_MODE_MPKT));
-
- /* enable emac for jumbo packets */
- EMAC_WR(EMAC_REG_EMAC_RX_MTU_SIZE,
- (EMAC_RX_MTU_SIZE_JUMBO_ENA |
- (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD))); /* -VLAN */
-
- /* strip CRC */
- NIG_WR(NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1);
-
- val = ((bp->dev->dev_addr[0] << 8) |
- bp->dev->dev_addr[1]);
- EMAC_WR(EMAC_REG_EMAC_MAC_MATCH, val);
-
- val = ((bp->dev->dev_addr[2] << 24) |
- (bp->dev->dev_addr[3] << 16) |
- (bp->dev->dev_addr[4] << 8) |
- bp->dev->dev_addr[5]);
- EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + 4, val);
-
- /* disable the NIG in/out to the bmac */
- NIG_WR(NIG_REG_BMAC0_IN_EN + port*4, 0x0);
- NIG_WR(NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0);
- NIG_WR(NIG_REG_BMAC0_OUT_EN + port*4, 0x0);
-
- /* enable the NIG in/out to the emac */
- NIG_WR(NIG_REG_EMAC0_IN_EN + port*4, 0x1);
- val = 0;
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- val = 1;
- NIG_WR(NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val);
- NIG_WR(NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1);
-
- if (CHIP_REV(bp) == CHIP_REV_FPGA) {
- /* take the BigMac out of reset */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
-
- /* enable access for bmac registers */
- NIG_WR(NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
- }
-
- bp->phy_flags |= PHY_EMAC_FLAG;
-
- bp->stats_state = STATS_STATE_ENABLE;
-}
-
-static void bnx2x_emac_program(struct bnx2x *bp)
-{
- u16 mode = 0;
- int port = bp->port;
-
- DP(NETIF_MSG_LINK, "setting link speed & duplex\n");
- bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
- (EMAC_MODE_25G_MODE |
- EMAC_MODE_PORT_MII_10M |
- EMAC_MODE_HALF_DUPLEX));
- switch (bp->line_speed) {
- case SPEED_10:
- mode |= EMAC_MODE_PORT_MII_10M;
- break;
-
- case SPEED_100:
- mode |= EMAC_MODE_PORT_MII;
- break;
-
- case SPEED_1000:
- mode |= EMAC_MODE_PORT_GMII;
- break;
-
- case SPEED_2500:
- mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII);
- break;
-
- default:
- /* 10G not valid for EMAC */
- BNX2X_ERR("Invalid line_speed 0x%x\n", bp->line_speed);
- break;
- }
-
- if (bp->duplex == DUPLEX_HALF)
- mode |= EMAC_MODE_HALF_DUPLEX;
- bnx2x_bits_en(bp, GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
- mode);
-
- bnx2x_leds_set(bp, bp->line_speed);
-}
-
-static void bnx2x_set_sgmii_tx_driver(struct bnx2x *bp)
-{
- u32 lp_up2;
- u32 tx_driver;
-
- /* read precomp */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_OVER_1G);
- bnx2x_mdio22_read(bp, MDIO_OVER_1G_LP_UP2, &lp_up2);
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_TX0);
- bnx2x_mdio22_read(bp, MDIO_TX0_TX_DRIVER, &tx_driver);
-
- /* bits [10:7] at lp_up2, positioned at [15:12] */
- lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
- MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
- MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);
-
- if ((lp_up2 != 0) &&
- (lp_up2 != (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK))) {
- /* replace tx_driver bits [15:12] */
- tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
- tx_driver |= lp_up2;
- bnx2x_mdio22_write(bp, MDIO_TX0_TX_DRIVER, tx_driver);
- }
-}
-
-static void bnx2x_pbf_update(struct bnx2x *bp)
-{
- int port = bp->port;
- u32 init_crd, crd;
- u32 count = 1000;
- u32 pause = 0;
-
- /* disable port */
- REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);
-
- /* wait for init credit */
- init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4);
- crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
- DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd);
-
- while ((init_crd != crd) && count) {
- msleep(5);
-
- crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
- count--;
- }
- crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
- if (init_crd != crd)
- BNX2X_ERR("BUG! init_crd 0x%x != crd 0x%x\n", init_crd, crd);
-
- if (bp->flow_ctrl & FLOW_CTRL_RX)
- pause = 1;
- REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, pause);
- if (pause) {
- /* update threshold */
- REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
- /* update init credit */
- init_crd = 778; /* (800-18-4) */
-
- } else {
- u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)/16;
-
- /* update threshold */
- REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
- /* update init credit */
- switch (bp->line_speed) {
- case SPEED_10:
- case SPEED_100:
- case SPEED_1000:
- init_crd = thresh + 55 - 22;
- break;
-
- case SPEED_2500:
- init_crd = thresh + 138 - 22;
- break;
-
- case SPEED_10000:
- init_crd = thresh + 553 - 22;
- break;
-
- default:
- BNX2X_ERR("Invalid line_speed 0x%x\n",
- bp->line_speed);
- break;
- }
- }
- REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd);
- DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n",
- bp->line_speed, init_crd);
-
- /* probe the credit changes */
- REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1);
- msleep(5);
- REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0);
-
- /* enable port */
- REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0);
-}
-
-static void bnx2x_update_mng(struct bnx2x *bp)
-{
- if (!nomcp)
- SHMEM_WR(bp, port_mb[bp->port].link_status,
- bp->link_status);
-}
-
-static void bnx2x_link_report(struct bnx2x *bp)
-{
- if (bp->link_up) {
- netif_carrier_on(bp->dev);
- printk(KERN_INFO PFX "%s NIC Link is Up, ", bp->dev->name);
-
- printk("%d Mbps ", bp->line_speed);
-
- if (bp->duplex == DUPLEX_FULL)
- printk("full duplex");
- else
- printk("half duplex");
-
- if (bp->flow_ctrl) {
- if (bp->flow_ctrl & FLOW_CTRL_RX) {
- printk(", receive ");
- if (bp->flow_ctrl & FLOW_CTRL_TX)
- printk("& transmit ");
- } else {
- printk(", transmit ");
- }
- printk("flow control ON");
- }
- printk("\n");
-
- } else { /* link_down */
- netif_carrier_off(bp->dev);
- printk(KERN_INFO PFX "%s NIC Link is Down\n", bp->dev->name);
- }
-}
-
-static void bnx2x_link_up(struct bnx2x *bp)
-{
- int port = bp->port;
-
- /* PBF - link up */
- bnx2x_pbf_update(bp);
-
- /* disable drain */
- NIG_WR(NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);
-
- /* update shared memory */
- bnx2x_update_mng(bp);
-
- /* indicate link up */
- bnx2x_link_report(bp);
-}
-
-static void bnx2x_link_down(struct bnx2x *bp)
-{
- int port = bp->port;
-
- /* notify stats */
- if (bp->stats_state != STATS_STATE_DISABLE) {
- bp->stats_state = STATS_STATE_STOP;
- DP(BNX2X_MSG_STATS, "stats_state - STOP\n");
- }
-
- /* indicate no mac active */
- bp->phy_flags &= ~(PHY_BMAC_FLAG | PHY_EMAC_FLAG);
-
- /* update shared memory */
- bnx2x_update_mng(bp);
-
- /* activate nig drain */
- NIG_WR(NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
-
- /* reset BigMac */
- bnx2x_bmac_rx_disable(bp);
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
-
- /* indicate link down */
- bnx2x_link_report(bp);
-}
-
-static void bnx2x_init_mac_stats(struct bnx2x *bp);
-
-/* This function is called upon link interrupt */
-static void bnx2x_link_update(struct bnx2x *bp)
-{
- int port = bp->port;
- int i;
- u32 gp_status;
- int link_10g;
-
- DP(NETIF_MSG_LINK, "port %x, %s, int_status 0x%x,"
- " int_mask 0x%x, saved_mask 0x%x, MI_INT %x, SERDES_LINK %x,"
- " 10G %x, XGXS_LINK %x\n", port,
- (bp->phy_flags & PHY_XGXS_FLAG)? "XGXS":"SerDes",
- REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4),
- REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), bp->nig_mask,
- REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18),
- REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c),
- REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
- REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)
- );
-
- might_sleep();
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_GP_STATUS);
- /* avoid fast toggling */
- for (i = 0; i < 10; i++) {
- msleep(10);
- bnx2x_mdio22_read(bp, MDIO_GP_STATUS_TOP_AN_STATUS1,
- &gp_status);
- }
-
- bnx2x_link_settings_status(bp, gp_status);
-
- /* anything 10 and over uses the bmac */
- link_10g = ((bp->line_speed >= SPEED_10000) &&
- (bp->line_speed <= SPEED_16000));
-
- bnx2x_link_int_ack(bp, link_10g);
-
- /* link is up only if both local phy and external phy are up */
- bp->link_up = (bp->phy_link_up && bnx2x_ext_phy_is_link_up(bp));
- if (bp->link_up) {
- if (link_10g) {
- bnx2x_bmac_enable(bp, 0);
- bnx2x_leds_set(bp, SPEED_10000);
-
- } else {
- bnx2x_emac_enable(bp);
- bnx2x_emac_program(bp);
-
- /* AN complete? */
- if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) {
- if (!(bp->phy_flags & PHY_SGMII_FLAG))
- bnx2x_set_sgmii_tx_driver(bp);
- }
- }
- bnx2x_link_up(bp);
-
- } else { /* link down */
- bnx2x_leds_unset(bp);
- bnx2x_link_down(bp);
- }
-
- bnx2x_init_mac_stats(bp);
-}
-
-/*
- * Init service functions
- */
-
-static void bnx2x_set_aer_mmd(struct bnx2x *bp)
-{
- u16 offset = (bp->phy_flags & PHY_XGXS_FLAG) ?
- (bp->phy_addr + bp->ser_lane) : 0;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_AER_BLOCK);
- bnx2x_mdio22_write(bp, MDIO_AER_BLOCK_AER_REG, 0x3800 + offset);
-}
-
-static void bnx2x_set_master_ln(struct bnx2x *bp)
-{
- u32 new_master_ln;
-
- /* set the master_ln for AN */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_XGXS_BLOCK2);
- bnx2x_mdio22_read(bp, MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
- &new_master_ln);
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
- (new_master_ln | bp->ser_lane));
-}
-
-static void bnx2x_reset_unicore(struct bnx2x *bp)
-{
- u32 mii_control;
- int i;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
- /* reset the unicore */
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control | MDIO_COMBO_IEEO_MII_CONTROL_RESET));
-
- /* wait for the reset to self clear */
- for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
- udelay(5);
-
- /* the reset erased the previous bank value */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
-
- if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) {
- udelay(5);
- return;
- }
- }
-
- BNX2X_ERR("BUG! %s (0x%x) is still in reset!\n",
- (bp->phy_flags & PHY_XGXS_FLAG)? "XGXS":"SerDes",
- bp->phy_addr);
-}
-
-static void bnx2x_set_swap_lanes(struct bnx2x *bp)
-{
- /* Each two bits represents a lane number:
- No swap is 0123 => 0x1b no need to enable the swap */
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_XGXS_BLOCK2);
- if (bp->rx_lane_swap != 0x1b) {
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_RX_LN_SWAP,
- (bp->rx_lane_swap |
- MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
- MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
- } else {
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
- }
-
- if (bp->tx_lane_swap != 0x1b) {
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_TX_LN_SWAP,
- (bp->tx_lane_swap |
- MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
- } else {
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
- }
-}
-
-static void bnx2x_set_parallel_detection(struct bnx2x *bp)
-{
- u32 control2;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_SERDES_DIGITAL);
- bnx2x_mdio22_read(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
- &control2);
-
- if (bp->autoneg & AUTONEG_PARALLEL) {
- control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
- } else {
- control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
- }
- bnx2x_mdio22_write(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
- control2);
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- DP(NETIF_MSG_LINK, "XGXS\n");
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_10G_PARALLEL_DETECT);
-
- bnx2x_mdio22_write(bp,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);
-
- bnx2x_mdio22_read(bp,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
- &control2);
-
- if (bp->autoneg & AUTONEG_PARALLEL) {
- control2 |=
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;
- } else {
- control2 &=
- ~MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;
- }
- bnx2x_mdio22_write(bp,
- MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
- control2);
-
- /* Disable parallel detection of HiG */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_XGXS_BLOCK2);
- bnx2x_mdio22_write(bp, MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
- MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
- MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
- }
-}
-
-static void bnx2x_set_autoneg(struct bnx2x *bp)
-{
- u32 reg_val;
-
- /* CL37 Autoneg */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
- if ((bp->req_autoneg & AUTONEG_SPEED) &&
- (bp->autoneg & AUTONEG_CL37)) {
- /* CL37 Autoneg Enabled */
- reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN;
- } else {
- /* CL37 Autoneg Disabled */
- reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
- MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN);
- }
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
-
- /* Enable/Disable Autodetection */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_SERDES_DIGITAL);
- bnx2x_mdio22_read(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val);
- reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN;
-
- if ((bp->req_autoneg & AUTONEG_SPEED) &&
- (bp->autoneg & AUTONEG_SGMII_FIBER_AUTODET)) {
- reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
- } else {
- reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
- }
- bnx2x_mdio22_write(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);
-
- /* Enable TetonII and BAM autoneg */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_BAM_NEXT_PAGE);
- bnx2x_mdio22_read(bp, MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
- ®_val);
- if ((bp->req_autoneg & AUTONEG_SPEED) &&
- (bp->autoneg & AUTONEG_CL37) && (bp->autoneg & AUTONEG_BAM)) {
- /* Enable BAM aneg Mode and TetonII aneg Mode */
- reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
- MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
- } else {
- /* TetonII and BAM Autoneg Disabled */
- reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
- MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
- }
- bnx2x_mdio22_write(bp, MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
- reg_val);
-
- /* Enable Clause 73 Aneg */
- if ((bp->req_autoneg & AUTONEG_SPEED) &&
- (bp->autoneg & AUTONEG_CL73)) {
- /* Enable BAM Station Manager */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_CL73_USERB0);
- bnx2x_mdio22_write(bp, MDIO_CL73_USERB0_CL73_BAM_CTRL1,
- (MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN |
- MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN |
- MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN));
-
- /* Merge CL73 and CL37 aneg resolution */
- bnx2x_mdio22_read(bp, MDIO_CL73_USERB0_CL73_BAM_CTRL3,
- ®_val);
- bnx2x_mdio22_write(bp, MDIO_CL73_USERB0_CL73_BAM_CTRL3,
- (reg_val |
- MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR));
-
- /* Set the CL73 AN speed */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_CL73_IEEEB1);
- bnx2x_mdio22_read(bp, MDIO_CL73_IEEEB1_AN_ADV2, ®_val);
- /* In the SerDes we support only the 1G.
- In the XGXS we support the 10G KX4
- but we currently do not support the KR */
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- DP(NETIF_MSG_LINK, "XGXS\n");
- /* 10G KX4 */
- reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
- } else {
- DP(NETIF_MSG_LINK, "SerDes\n");
- /* 1000M KX */
- reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;
- }
- bnx2x_mdio22_write(bp, MDIO_CL73_IEEEB1_AN_ADV2, reg_val);
-
- /* CL73 Autoneg Enabled */
- reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;
- } else {
- /* CL73 Autoneg Disabled */
- reg_val = 0;
- }
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_CL73_IEEEB0);
- bnx2x_mdio22_write(bp, MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
-}
-
-/* program SerDes, forced speed */
-static void bnx2x_program_serdes(struct bnx2x *bp)
-{
- u32 reg_val;
-
- /* program duplex, disable autoneg */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL, ®_val);
- reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX |
- MDIO_COMBO_IEEO_MII_CONTROL_AN_EN);
- if (bp->req_duplex == DUPLEX_FULL)
- reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
-
- /* program speed
- - needed only if the speed is greater than 1G (2.5G or 10G) */
- if (bp->req_line_speed > SPEED_1000) {
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_SERDES_DIGITAL);
- bnx2x_mdio22_read(bp, MDIO_SERDES_DIGITAL_MISC1, ®_val);
- /* clearing the speed value before setting the right speed */
- reg_val &= ~MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK;
- reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M |
- MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
- if (bp->req_line_speed == SPEED_10000)
- reg_val |=
- MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4;
- bnx2x_mdio22_write(bp, MDIO_SERDES_DIGITAL_MISC1, reg_val);
- }
-}
-
-static void bnx2x_set_brcm_cl37_advertisment(struct bnx2x *bp)
-{
- u32 val = 0;
-
- /* configure the 48 bits for BAM AN */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_OVER_1G);
-
- /* set extended capabilities */
- if (bp->advertising & ADVERTISED_2500baseX_Full)
- val |= MDIO_OVER_1G_UP1_2_5G;
- if (bp->advertising & ADVERTISED_10000baseT_Full)
- val |= MDIO_OVER_1G_UP1_10G;
- bnx2x_mdio22_write(bp, MDIO_OVER_1G_UP1, val);
-
- bnx2x_mdio22_write(bp, MDIO_OVER_1G_UP3, 0);
-}
-
-static void bnx2x_set_ieee_aneg_advertisment(struct bnx2x *bp)
-{
- u32 an_adv;
-
- /* for AN, we are always publishing full duplex */
- an_adv = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
-
- /* resolve pause mode and advertisement
- * Please refer to Table 28B-3 of the 802.3ab-1999 spec */
- if (bp->req_autoneg & AUTONEG_FLOW_CTRL) {
- switch (bp->req_flow_ctrl) {
- case FLOW_CTRL_AUTO:
- if (bp->dev->mtu <= 4500) {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
- bp->advertising |= (ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- } else {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
- bp->advertising |= ADVERTISED_Asym_Pause;
- }
- break;
-
- case FLOW_CTRL_TX:
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
- bp->advertising |= ADVERTISED_Asym_Pause;
- break;
-
- case FLOW_CTRL_RX:
- if (bp->dev->mtu <= 4500) {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
- bp->advertising |= (ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- } else {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
- bp->advertising &= ~(ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- }
- break;
-
- case FLOW_CTRL_BOTH:
- if (bp->dev->mtu <= 4500) {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
- bp->advertising |= (ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- } else {
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
- bp->advertising |= ADVERTISED_Asym_Pause;
- }
- break;
-
- case FLOW_CTRL_NONE:
- default:
- an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
- bp->advertising &= ~(ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- break;
- }
- } else { /* forced mode */
- switch (bp->req_flow_ctrl) {
- case FLOW_CTRL_AUTO:
- DP(NETIF_MSG_LINK, "req_flow_ctrl 0x%x while"
- " req_autoneg 0x%x\n",
- bp->req_flow_ctrl, bp->req_autoneg);
- break;
-
- case FLOW_CTRL_TX:
- an_adv |=
- MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
- bp->advertising |= ADVERTISED_Asym_Pause;
- break;
-
- case FLOW_CTRL_RX:
- case FLOW_CTRL_BOTH:
- an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
- bp->advertising |= (ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- break;
-
- case FLOW_CTRL_NONE:
- default:
- an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
- bp->advertising &= ~(ADVERTISED_Pause |
- ADVERTISED_Asym_Pause);
- break;
- }
- }
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_AUTO_NEG_ADV, an_adv);
-}
-
-static void bnx2x_restart_autoneg(struct bnx2x *bp)
-{
- if (bp->autoneg & AUTONEG_CL73) {
- /* enable and restart clause 73 aneg */
- u32 an_ctrl;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_CL73_IEEEB0);
- bnx2x_mdio22_read(bp, MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- &an_ctrl);
- bnx2x_mdio22_write(bp, MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- (an_ctrl |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
-
- } else {
- /* Enable and restart BAM/CL37 aneg */
- u32 mii_control;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control |
- MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
- MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
- }
-}
-
-static void bnx2x_initialize_sgmii_process(struct bnx2x *bp)
-{
- u32 control1;
-
- /* in SGMII mode, the unicore is always slave */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_SERDES_DIGITAL);
- bnx2x_mdio22_read(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
- &control1);
- control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
- /* set sgmii mode (and not fiber) */
- control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
- MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
- bnx2x_mdio22_write(bp, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
- control1);
-
- /* if forced speed */
- if (!(bp->req_autoneg & AUTONEG_SPEED)) {
- /* set speed, disable autoneg */
- u32 mii_control;
-
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
- mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
- MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK |
- MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);
-
- switch (bp->req_line_speed) {
- case SPEED_100:
- mii_control |=
- MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100;
- break;
- case SPEED_1000:
- mii_control |=
- MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000;
- break;
- case SPEED_10:
- /* there is nothing to set for 10M */
- break;
- default:
- /* invalid speed for SGMII */
- DP(NETIF_MSG_LINK, "Invalid req_line_speed 0x%x\n",
- bp->req_line_speed);
- break;
- }
-
- /* setting the full duplex */
- if (bp->req_duplex == DUPLEX_FULL)
- mii_control |=
- MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- mii_control);
-
- } else { /* AN mode */
- /* enable and restart AN */
- bnx2x_restart_autoneg(bp);
- }
-}
-
-static void bnx2x_link_int_enable(struct bnx2x *bp)
-{
- int port = bp->port;
- u32 ext_phy_type;
- u32 mask;
-
- /* setting the status to report on link up
- for either XGXS or SerDes */
- bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
- (NIG_STATUS_XGXS0_LINK10G |
- NIG_STATUS_XGXS0_LINK_STATUS |
- NIG_STATUS_SERDES0_LINK_STATUS));
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- mask = (NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_XGXS0_LINK_STATUS);
- DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n");
- ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
- if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
- (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) &&
- (ext_phy_type !=
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) {
- mask |= NIG_MASK_MI_INT;
- DP(NETIF_MSG_LINK, "enabled external phy int\n");
- }
-
- } else { /* SerDes */
- mask = NIG_MASK_SERDES0_LINK_STATUS;
- DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n");
- ext_phy_type = SERDES_EXT_PHY_TYPE(bp);
- if ((ext_phy_type !=
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) &&
- (ext_phy_type !=
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN)) {
- mask |= NIG_MASK_MI_INT;
- DP(NETIF_MSG_LINK, "enabled external phy int\n");
- }
- }
- bnx2x_bits_en(bp,
- NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
- mask);
- DP(NETIF_MSG_LINK, "port %x, %s, int_status 0x%x,"
- " int_mask 0x%x, MI_INT %x, SERDES_LINK %x,"
- " 10G %x, XGXS_LINK %x\n", port,
- (bp->phy_flags & PHY_XGXS_FLAG)? "XGXS":"SerDes",
- REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4),
- REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
- REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18),
- REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c),
- REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
- REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)
- );
-}
-
-static void bnx2x_bcm8072_external_rom_boot(struct bnx2x *bp)
-{
- u32 ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
- u32 fw_ver1, fw_ver2;
-
- /* Need to wait 200ms after reset */
- msleep(200);
- /* Boot port from external ROM
- * Set ser_boot_ctl bit in the MISC_CTRL1 register
- */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- EXT_PHY_KR_MISC_CTRL1, 0x0001);
-
- /* Reset internal microprocessor */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_GEN_CTRL,
- EXT_PHY_KR_ROM_RESET_INTERNAL_MP);
- /* set micro reset = 0 */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_GEN_CTRL,
- EXT_PHY_KR_ROM_MICRO_RESET);
- /* Reset internal microprocessor */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_GEN_CTRL,
- EXT_PHY_KR_ROM_RESET_INTERNAL_MP);
- /* wait for 100ms for code download via SPI port */
- msleep(100);
-
- /* Clear ser_boot_ctl bit */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- EXT_PHY_KR_MISC_CTRL1, 0x0000);
- /* Wait 100ms */
- msleep(100);
-
- /* Print the PHY FW version */
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0xca19, &fw_ver1);
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0xca1a, &fw_ver2);
- DP(NETIF_MSG_LINK,
- "8072 FW version 0x%x:0x%x\n", fw_ver1, fw_ver2);
-}
-
-static void bnx2x_bcm8072_force_10G(struct bnx2x *bp)
-{
- u32 ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
-
- /* Force KR or KX */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_CTRL,
- 0x2040);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_CTRL2,
- 0x000b);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD, EXT_PHY_KR_PMD_CTRL,
- 0x0000);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD, EXT_PHY_KR_CTRL,
- 0x0000);
-}
-
-static void bnx2x_ext_phy_init(struct bnx2x *bp)
-{
- u32 ext_phy_type;
- u32 ext_phy_addr;
- u32 cnt;
- u32 ctrl;
- u32 val = 0;
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
-
- ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
- /* Make sure that the soft reset is off (expect for the 8072:
- * due to the lock, it will be done inside the specific
- * handling)
- */
- if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
- (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) &&
- (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN) &&
- (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072)) {
- /* Wait for soft reset to get cleared upto 1 sec */
- for (cnt = 0; cnt < 1000; cnt++) {
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CNTL, &ctrl);
- if (!(ctrl & (1<<15)))
- break;
- msleep(1);
- }
- DP(NETIF_MSG_LINK,
- "control reg 0x%x (after %d ms)\n", ctrl, cnt);
- }
-
- switch (ext_phy_type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "XGXS Direct\n");
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- DP(NETIF_MSG_LINK, "XGXS 8705\n");
-
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_PMD_MISC_CNTL,
- 0x8288);
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_PHY_IDENTIFIER,
- 0x7fbf);
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CMU_PLL_BYPASS,
- 0x0100);
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_WIS_DEVAD,
- EXT_PHY_OPT_LASI_CNTL, 0x1);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- DP(NETIF_MSG_LINK, "XGXS 8706\n");
-
- if (!(bp->req_autoneg & AUTONEG_SPEED)) {
- /* Force speed */
- if (bp->req_line_speed == SPEED_10000) {
- DP(NETIF_MSG_LINK,
- "XGXS 8706 force 10Gbps\n");
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_PMD_DIGITAL_CNT,
- 0x400);
- } else {
- /* Force 1Gbps */
- DP(NETIF_MSG_LINK,
- "XGXS 8706 force 1Gbps\n");
-
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CNTL,
- 0x0040);
-
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CNTL2,
- 0x000D);
- }
-
- /* Enable LASI */
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_CNTL,
- 0x1);
- } else {
- /* AUTONEG */
- /* Allow CL37 through CL73 */
- DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n");
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_AN_CL37_CL73,
- 0x040c);
-
- /* Enable Full-Duplex advertisment on CL37 */
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_AN_CL37_FD,
- 0x0020);
- /* Enable CL37 AN */
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_AN_CL37_AN,
- 0x1000);
- /* Advertise 10G/1G support */
- if (bp->advertising &
- ADVERTISED_1000baseT_Full)
- val = (1<<5);
- if (bp->advertising &
- ADVERTISED_10000baseT_Full)
- val |= (1<<7);
-
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_AN_ADV, val);
- /* Enable LASI */
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_CNTL,
- 0x1);
-
- /* Enable clause 73 AN */
- bnx2x_mdio45_write(bp, ext_phy_addr,
- EXT_PHY_AUTO_NEG_DEVAD,
- EXT_PHY_OPT_CNTL,
- 0x1200);
- }
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- /* Wait for soft reset to get cleared upto 1 sec */
- for (cnt = 0; cnt < 1000; cnt++) {
- bnx2x_mdio45_ctrl_read(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CNTL, &ctrl);
- if (!(ctrl & (1<<15)))
- break;
- msleep(1);
- }
- DP(NETIF_MSG_LINK,
- "8072 control reg 0x%x (after %d ms)\n",
- ctrl, cnt);
-
- bnx2x_bcm8072_external_rom_boot(bp);
- DP(NETIF_MSG_LINK, "Finshed loading 8072 KR ROM\n");
-
- /* enable LASI */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0x9000, 0x0400);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- EXT_PHY_KR_LASI_CNTL, 0x0004);
-
- /* If this is forced speed, set to KR or KX
- * (all other are not supported)
- */
- if (!(bp->req_autoneg & AUTONEG_SPEED)) {
- if (bp->req_line_speed == SPEED_10000) {
- bnx2x_bcm8072_force_10G(bp);
- DP(NETIF_MSG_LINK,
- "Forced speed 10G on 8072\n");
- /* unlock */
- bnx2x_hw_unlock(bp,
- HW_LOCK_RESOURCE_8072_MDIO);
- break;
- } else
- val = (1<<5);
- } else {
-
- /* Advertise 10G/1G support */
- if (bp->advertising &
- ADVERTISED_1000baseT_Full)
- val = (1<<5);
- if (bp->advertising &
- ADVERTISED_10000baseT_Full)
- val |= (1<<7);
- }
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- 0x11, val);
- /* Add support for CL37 ( passive mode ) I */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- 0x8370, 0x040c);
- /* Add support for CL37 ( passive mode ) II */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- 0xffe4, 0x20);
- /* Add support for CL37 ( passive mode ) III */
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- 0xffe0, 0x1000);
- /* Restart autoneg */
- msleep(500);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_CTRL, 0x1200);
- DP(NETIF_MSG_LINK, "8072 Autoneg Restart: "
- "1G %ssupported 10G %ssupported\n",
- (val & (1<<5)) ? "" : "not ",
- (val & (1<<7)) ? "" : "not ");
-
- /* unlock */
- bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- DP(NETIF_MSG_LINK,
- "Setting the SFX7101 LASI indication\n");
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_LASI_CNTL, 0x1);
- DP(NETIF_MSG_LINK,
- "Setting the SFX7101 LED to blink on traffic\n");
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- 0xC007, (1<<3));
-
- /* read modify write pause advertizing */
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_AUTO_NEG_ADVERT, &val);
- val &= ~EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_BOTH;
- /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
- if (bp->advertising & ADVERTISED_Pause)
- val |= EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE;
-
- if (bp->advertising & ADVERTISED_Asym_Pause) {
- val |=
- EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_ASYMMETRIC;
- }
- DP(NETIF_MSG_LINK, "SFX7101 AN advertize 0x%x\n", val);
- bnx2x_mdio45_vwrite(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_AUTO_NEG_ADVERT, val);
- /* Restart autoneg */
- bnx2x_mdio45_read(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_CTRL, &val);
- val |= 0x200;
- bnx2x_mdio45_write(bp, ext_phy_addr,
- EXT_PHY_KR_AUTO_NEG_DEVAD,
- EXT_PHY_KR_CTRL, val);
- break;
-
- default:
- BNX2X_ERR("BAD XGXS ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- break;
- }
-
- } else { /* SerDes */
-/* ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_SERDES_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_SERDES_EXT_PHY_ADDR_SHIFT);
-*/
- ext_phy_type = SERDES_EXT_PHY_TYPE(bp);
- switch (ext_phy_type) {
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "SerDes Direct\n");
- break;
-
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
- DP(NETIF_MSG_LINK, "SerDes 5482\n");
- break;
-
- default:
- DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- break;
- }
- }
-}
-
-static void bnx2x_ext_phy_reset(struct bnx2x *bp)
-{
- u32 ext_phy_type;
- u32 ext_phy_addr = ((bp->ext_phy_config &
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
- PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
- u32 board = (bp->board & SHARED_HW_CFG_BOARD_TYPE_MASK);
-
- /* The PHY reset is controled by GPIO 1
- * Give it 1ms of reset pulse
- */
- if ((board != SHARED_HW_CFG_BOARD_TYPE_BCM957710T1002G) &&
- (board != SHARED_HW_CFG_BOARD_TYPE_BCM957710T1003G)) {
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW);
- msleep(1);
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH);
- }
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
- switch (ext_phy_type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "XGXS Direct\n");
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- DP(NETIF_MSG_LINK, "XGXS 8705/8706\n");
- bnx2x_mdio45_write(bp, ext_phy_addr,
- EXT_PHY_OPT_PMA_PMD_DEVAD,
- EXT_PHY_OPT_CNTL, 0xa040);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- DP(NETIF_MSG_LINK, "XGXS 8072\n");
- bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- bnx2x_mdio45_ctrl_write(bp, GRCBASE_EMAC0,
- ext_phy_addr,
- EXT_PHY_KR_PMA_PMD_DEVAD,
- 0, 1<<15);
- bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- DP(NETIF_MSG_LINK, "XGXS SFX7101\n");
- break;
-
- default:
- DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- break;
- }
-
- } else { /* SerDes */
- ext_phy_type = SERDES_EXT_PHY_TYPE(bp);
- switch (ext_phy_type) {
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "SerDes Direct\n");
- break;
-
- case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
- DP(NETIF_MSG_LINK, "SerDes 5482\n");
- break;
-
- default:
- DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
- bp->ext_phy_config);
- break;
- }
- }
-}
-
-static void bnx2x_link_initialize(struct bnx2x *bp)
-{
- int port = bp->port;
+/* end of fast path */
+
- /* disable attentions */
- bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
- (NIG_MASK_XGXS0_LINK_STATUS |
- NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_SERDES0_LINK_STATUS |
- NIG_MASK_MI_INT));
+/* Link */
- /* Activate the external PHY */
- bnx2x_ext_phy_reset(bp);
+/*
+ * General service functions
+ */
- bnx2x_set_aer_mmd(bp);
+static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource)
+{
+ u32 lock_status;
+ u32 resource_bit = (1 << resource);
+ u8 port = bp->port;
+ int cnt;
- if (bp->phy_flags & PHY_XGXS_FLAG)
- bnx2x_set_master_ln(bp);
+ /* Validating that the resource is within range */
+ if (resource > HW_LOCK_MAX_RESOURCE_VALUE) {
+ DP(NETIF_MSG_HW,
+ "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n",
+ resource, HW_LOCK_MAX_RESOURCE_VALUE);
+ return -EINVAL;
+ }
- /* reset the SerDes and wait for reset bit return low */
- bnx2x_reset_unicore(bp);
+ /* Validating that the resource is not already taken */
+ lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8);
+ if (lock_status & resource_bit) {
+ DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n",
+ lock_status, resource_bit);
+ return -EEXIST;
+ }
- bnx2x_set_aer_mmd(bp);
+ /* Try for 1 second every 5ms */
+ for (cnt = 0; cnt < 200; cnt++) {
+ /* Try to acquire the lock */
+ REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + port*8 + 4,
+ resource_bit);
+ lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8);
+ if (lock_status & resource_bit)
+ return 0;
- /* setting the masterLn_def again after the reset */
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- bnx2x_set_master_ln(bp);
- bnx2x_set_swap_lanes(bp);
+ msleep(5);
}
+ DP(NETIF_MSG_HW, "Timeout\n");
+ return -EAGAIN;
+}
- /* Set Parallel Detect */
- if (bp->req_autoneg & AUTONEG_SPEED)
- bnx2x_set_parallel_detection(bp);
+static int bnx2x_hw_unlock(struct bnx2x *bp, u32 resource)
+{
+ u32 lock_status;
+ u32 resource_bit = (1 << resource);
+ u8 port = bp->port;
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- if (bp->req_line_speed &&
- bp->req_line_speed < SPEED_1000) {
- bp->phy_flags |= PHY_SGMII_FLAG;
- } else {
- bp->phy_flags &= ~PHY_SGMII_FLAG;
- }
+ /* Validating that the resource is within range */
+ if (resource > HW_LOCK_MAX_RESOURCE_VALUE) {
+ DP(NETIF_MSG_HW,
+ "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n",
+ resource, HW_LOCK_MAX_RESOURCE_VALUE);
+ return -EINVAL;
+ }
+
+ /* Validating that the resource is currently taken */
+ lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8);
+ if (!(lock_status & resource_bit)) {
+ DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n",
+ lock_status, resource_bit);
+ return -EFAULT;
}
- if (!(bp->phy_flags & PHY_SGMII_FLAG)) {
- u16 bank, rx_eq;
+ REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + port*8, resource_bit);
+ return 0;
+}
+
+/* HW Lock for shared dual port PHYs */
+static void bnx2x_phy_hw_lock(struct bnx2x *bp)
+{
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
- rx_eq = ((bp->serdes_config &
- PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >>
- PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT);
+ mutex_lock(&bp->phy_mutex);
- DP(NETIF_MSG_LINK, "setting rx eq to %d\n", rx_eq);
- for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL;
- bank += (MDIO_REG_BANK_RX1 - MDIO_REG_BANK_RX0)) {
- MDIO_SET_REG_BANK(bp, bank);
- bnx2x_mdio22_write(bp, MDIO_RX0_RX_EQ_BOOST,
- ((rx_eq &
- MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) |
- MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL));
- }
+ if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) ||
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073))
+ bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO);
+}
- /* forced speed requested? */
- if (!(bp->req_autoneg & AUTONEG_SPEED)) {
- DP(NETIF_MSG_LINK, "not SGMII, no AN\n");
+static void bnx2x_phy_hw_unlock(struct bnx2x *bp)
+{
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
- /* disable autoneg */
- bnx2x_set_autoneg(bp);
+ if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) ||
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073))
+ bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_8072_MDIO);
- /* program speed and duplex */
- bnx2x_program_serdes(bp);
+ mutex_unlock(&bp->phy_mutex);
+}
- } else { /* AN_mode */
- DP(NETIF_MSG_LINK, "not SGMII, AN\n");
+int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode)
+{
+ /* The GPIO should be swapped if swap register is set and active */
+ int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) &&
+ REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ bp->port;
+ int gpio_shift = gpio_num +
+ (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0);
+ u32 gpio_mask = (1 << gpio_shift);
+ u32 gpio_reg;
- /* AN enabled */
- bnx2x_set_brcm_cl37_advertisment(bp);
+ if (gpio_num > MISC_REGISTERS_GPIO_3) {
+ BNX2X_ERR("Invalid GPIO %d\n", gpio_num);
+ return -EINVAL;
+ }
- /* program duplex & pause advertisement (for aneg) */
- bnx2x_set_ieee_aneg_advertisment(bp);
+ bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
+ /* read GPIO and mask except the float bits */
+ gpio_reg = (REG_RD(bp, MISC_REG_GPIO) & MISC_REGISTERS_GPIO_FLOAT);
- /* enable autoneg */
- bnx2x_set_autoneg(bp);
+ switch (mode) {
+ case MISC_REGISTERS_GPIO_OUTPUT_LOW:
+ DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output low\n",
+ gpio_num, gpio_shift);
+ /* clear FLOAT and set CLR */
+ gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
+ gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_CLR_POS);
+ break;
- /* enable and restart AN */
- bnx2x_restart_autoneg(bp);
- }
+ case MISC_REGISTERS_GPIO_OUTPUT_HIGH:
+ DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output high\n",
+ gpio_num, gpio_shift);
+ /* clear FLOAT and set SET */
+ gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
+ gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_SET_POS);
+ break;
- } else { /* SGMII mode */
- DP(NETIF_MSG_LINK, "SGMII\n");
+ case MISC_REGISTERS_GPIO_INPUT_HI_Z :
+ DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> input\n",
+ gpio_num, gpio_shift);
+ /* set FLOAT */
+ gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS);
+ break;
- bnx2x_initialize_sgmii_process(bp);
+ default:
+ break;
}
- /* init ext phy and enable link state int */
- bnx2x_ext_phy_init(bp);
+ REG_WR(bp, MISC_REG_GPIO, gpio_reg);
+ bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_GPIO);
- /* enable the interrupt */
- bnx2x_link_int_enable(bp);
+ return 0;
}
-static void bnx2x_phy_deassert(struct bnx2x *bp)
+static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode)
{
- int port = bp->port;
- u32 val;
-
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- DP(NETIF_MSG_LINK, "XGXS\n");
- val = XGXS_RESET_BITS;
+ u32 spio_mask = (1 << spio_num);
+ u32 spio_reg;
- } else { /* SerDes */
- DP(NETIF_MSG_LINK, "SerDes\n");
- val = SERDES_RESET_BITS;
+ if ((spio_num < MISC_REGISTERS_SPIO_4) ||
+ (spio_num > MISC_REGISTERS_SPIO_7)) {
+ BNX2X_ERR("Invalid SPIO %d\n", spio_num);
+ return -EINVAL;
}
- val = val << (port*16);
+ bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_SPIO);
+ /* read SPIO and mask except the float bits */
+ spio_reg = (REG_RD(bp, MISC_REG_SPIO) & MISC_REGISTERS_SPIO_FLOAT);
- /* reset and unreset the SerDes/XGXS */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
- msleep(5);
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);
-}
+ switch (mode) {
+ case MISC_REGISTERS_SPIO_OUTPUT_LOW :
+ DP(NETIF_MSG_LINK, "Set SPIO %d -> output low\n", spio_num);
+ /* clear FLOAT and set CLR */
+ spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
+ spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_CLR_POS);
+ break;
-static int bnx2x_phy_init(struct bnx2x *bp)
-{
- DP(NETIF_MSG_LINK, "started\n");
- if (CHIP_REV(bp) == CHIP_REV_FPGA) {
- bp->phy_flags |= PHY_EMAC_FLAG;
- bp->link_up = 1;
- bp->line_speed = SPEED_10000;
- bp->duplex = DUPLEX_FULL;
- NIG_WR(NIG_REG_EGRESS_DRAIN0_MODE + bp->port*4, 0);
- bnx2x_emac_enable(bp);
- bnx2x_link_report(bp);
- return 0;
+ case MISC_REGISTERS_SPIO_OUTPUT_HIGH :
+ DP(NETIF_MSG_LINK, "Set SPIO %d -> output high\n", spio_num);
+ /* clear FLOAT and set SET */
+ spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
+ spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_SET_POS);
+ break;
- } else if (CHIP_REV(bp) == CHIP_REV_EMUL) {
- bp->phy_flags |= PHY_BMAC_FLAG;
- bp->link_up = 1;
- bp->line_speed = SPEED_10000;
- bp->duplex = DUPLEX_FULL;
- NIG_WR(NIG_REG_EGRESS_DRAIN0_MODE + bp->port*4, 0);
- bnx2x_bmac_enable(bp, 0);
- bnx2x_link_report(bp);
- return 0;
+ case MISC_REGISTERS_SPIO_INPUT_HI_Z:
+ DP(NETIF_MSG_LINK, "Set SPIO %d -> input\n", spio_num);
+ /* set FLOAT */
+ spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS);
+ break;
- } else {
- bnx2x_phy_deassert(bp);
- bnx2x_link_initialize(bp);
+ default:
+ break;
}
+ REG_WR(bp, MISC_REG_SPIO, spio_reg);
+ bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_SPIO);
+
return 0;
}
-static void bnx2x_link_reset(struct bnx2x *bp)
+static void bnx2x_calc_fc_adv(struct bnx2x *bp)
{
- int port = bp->port;
- u32 board = (bp->board & SHARED_HW_CFG_BOARD_TYPE_MASK);
-
- /* update shared memory */
- bp->link_status = 0;
- bnx2x_update_mng(bp);
-
- /* disable attentions */
- bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
- (NIG_MASK_XGXS0_LINK_STATUS |
- NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_SERDES0_LINK_STATUS |
- NIG_MASK_MI_INT));
-
- /* activate nig drain */
- NIG_WR(NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
+ switch (bp->link_vars.ieee_fc) {
+ case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE:
+ bp->advertising &= ~(ADVERTISED_Asym_Pause |
+ ADVERTISED_Pause);
+ break;
+ case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH:
+ bp->advertising |= (ADVERTISED_Asym_Pause |
+ ADVERTISED_Pause);
+ break;
+ case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC:
+ bp->advertising |= ADVERTISED_Asym_Pause;
+ break;
+ default:
+ bp->advertising &= ~(ADVERTISED_Asym_Pause |
+ ADVERTISED_Pause);
+ break;
+ }
+}
- /* disable nig egress interface */
- NIG_WR(NIG_REG_BMAC0_OUT_EN + port*4, 0);
- NIG_WR(NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
+static void bnx2x_link_report(struct bnx2x *bp)
+{
+ if (bp->link_vars.link_up) {
+ if (bp->state == BNX2X_STATE_OPEN)
+ netif_carrier_on(bp->dev);
+ printk(KERN_INFO PFX "%s NIC Link is Up, ", bp->dev->name);
- /* Stop BigMac rx */
- bnx2x_bmac_rx_disable(bp);
+ printk("%d Mbps ", bp->link_vars.line_speed);
- /* disable emac */
- NIG_WR(NIG_REG_NIG_EMAC0_EN + port*4, 0);
+ if (bp->link_vars.duplex == DUPLEX_FULL)
+ printk("full duplex");
+ else
+ printk("half duplex");
- msleep(10);
+ if (bp->link_vars.flow_ctrl != FLOW_CTRL_NONE) {
+ if (bp->link_vars.flow_ctrl & FLOW_CTRL_RX) {
+ printk(", receive ");
+ if (bp->link_vars.flow_ctrl & FLOW_CTRL_TX)
+ printk("& transmit ");
+ } else {
+ printk(", transmit ");
+ }
+ printk("flow control ON");
+ }
+ printk("\n");
- /* The PHY reset is controled by GPIO 1
- * Hold it as output low
- */
- if ((board != SHARED_HW_CFG_BOARD_TYPE_BCM957710T1002G) &&
- (board != SHARED_HW_CFG_BOARD_TYPE_BCM957710T1003G)) {
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW);
- DP(NETIF_MSG_LINK, "reset external PHY\n");
+ } else { /* link_down */
+ netif_carrier_off(bp->dev);
+ printk(KERN_ERR PFX "%s NIC Link is Down\n", bp->dev->name);
}
+}
+
+static u8 bnx2x_initial_phy_init(struct bnx2x *bp)
+{
+ u8 rc;
- /* reset the SerDes/XGXS */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
- (0x1ff << (port*16)));
+ /* Initialize link parameters structure variables */
+ bp->link_params.mtu = bp->dev->mtu;
- /* reset BigMac */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ bnx2x_phy_hw_lock(bp);
+ rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
- /* disable nig ingress interface */
- NIG_WR(NIG_REG_BMAC0_IN_EN + port*4, 0);
- NIG_WR(NIG_REG_EMAC0_IN_EN + port*4, 0);
+ if (bp->link_vars.link_up)
+ bnx2x_link_report(bp);
- /* set link down */
- bp->link_up = 0;
+ bnx2x_calc_fc_adv(bp);
+ return rc;
}
-#ifdef BNX2X_XGXS_LB
-static void bnx2x_set_xgxs_loopback(struct bnx2x *bp, int is_10g)
+static void bnx2x_link_set(struct bnx2x *bp)
{
- int port = bp->port;
+ bnx2x_phy_hw_lock(bp);
+ bnx2x_phy_init(&bp->link_params, &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
- if (is_10g) {
- u32 md_devad;
+ bnx2x_calc_fc_adv(bp);
+}
- DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n");
+static void bnx2x__link_reset(struct bnx2x *bp)
+{
+ bnx2x_phy_hw_lock(bp);
+ bnx2x_link_reset(&bp->link_params, &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
+}
- /* change the uni_phy_addr in the nig */
- REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18),
- &md_devad);
- NIG_WR(NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5);
+static u8 bnx2x_link_test(struct bnx2x *bp)
+{
+ u8 rc;
- /* change the aer mmd */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_AER_BLOCK);
- bnx2x_mdio22_write(bp, MDIO_AER_BLOCK_AER_REG, 0x2800);
+ bnx2x_phy_hw_lock(bp);
+ rc = bnx2x_test_link(&bp->link_params, &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
- /* config combo IEEE0 control reg for loopback */
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_CL73_IEEEB0);
- bnx2x_mdio22_write(bp, MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- 0x6041);
+ return rc;
+}
- /* set aer mmd back */
- bnx2x_set_aer_mmd(bp);
+/* This function is called upon link interrupt */
+static void bnx2x_link_attn(struct bnx2x *bp)
+{
+ bnx2x_phy_hw_lock(bp);
+ bnx2x_link_update(&bp->link_params, &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
- /* and md_devad */
- NIG_WR(NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, md_devad);
+ /* indicate link status */
+ bnx2x_link_report(bp);
+}
- } else {
- u32 mii_control;
+static void bnx2x__link_status_update(struct bnx2x *bp)
+{
+ if (bp->state != BNX2X_STATE_OPEN)
+ return;
- DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n");
+ bnx2x_link_status_update(&bp->link_params, &bp->link_vars);
- MDIO_SET_REG_BANK(bp, MDIO_REG_BANK_COMBO_IEEE0);
- bnx2x_mdio22_read(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
- bnx2x_mdio22_write(bp, MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control |
- MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK));
- }
+ /* indicate link status */
+ bnx2x_link_report(bp);
}
-#endif
-/* end of PHY/MAC */
+/* end of Link */
/* slow path */
bp->nig_mask = REG_RD(bp, nig_int_mask_addr);
REG_WR(bp, nig_int_mask_addr, 0);
- bnx2x_link_update(bp);
+ bnx2x_link_attn(bp);
/* handle unicore attn? */
}
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
MISC_REGISTERS_GPIO_OUTPUT_LOW);
/* mark the failure */
- bp->ext_phy_config &=
+ bp->link_params.ext_phy_config &=
~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
- bp->ext_phy_config |=
+ bp->link_params.ext_phy_config |=
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE;
SHMEM_WR(bp,
dev_info.port_hw_config[port].
external_phy_config,
- bp->ext_phy_config);
+ bp->link_params.ext_phy_config);
/* log the failure */
printk(KERN_ERR PFX "Fan Failure on Network"
" Controller %s has caused the driver to"
#endif
(port ? DMAE_CMD_PORT_1 : DMAE_CMD_PORT_0));
- if (bp->link_up)
+ if (bp->link_vars.link_up)
opcode |= (DMAE_CMD_C_DST_GRC | DMAE_CMD_C_ENABLE);
dmae = bnx2x_sp(bp, dmae[bp->executer_idx++]);
dmae->dst_addr_hi = 0;
dmae->len = (offsetof(struct bnx2x_eth_stats, mac_stx_end) -
sizeof(u32)) >> 2;
- if (bp->link_up) {
+ if (bp->link_vars.link_up) {
dmae->comp_addr_lo = dmae_reg_go_c[loader_idx] >> 2;
dmae->comp_addr_hi = 0;
dmae->comp_val = 1;
}
}
- if (!bp->link_up) {
+ if (!bp->link_vars.link_up) {
/* no need to collect statistics in link down */
return;
}
#endif
(port ? DMAE_CMD_PORT_1 : DMAE_CMD_PORT_0));
- if (bp->phy_flags & PHY_BMAC_FLAG) {
+ if (bp->link_vars.mac_type == MAC_TYPE_BMAC) {
mac_addr = (port ? NIG_REG_INGRESS_BMAC1_MEM :
NIG_REG_INGRESS_BMAC0_MEM);
dmae->comp_addr_hi = 0;
dmae->comp_val = 1;
- } else if (bp->phy_flags & PHY_EMAC_FLAG) {
+ } else if (bp->link_vars.mac_type == MAC_TYPE_EMAC) {
mac_addr = (port ? GRCBASE_EMAC1 : GRCBASE_EMAC0);
if (!bnx2x_update_storm_stats(bp)) {
- if (bp->phy_flags & PHY_BMAC_FLAG) {
+ if (bp->link_vars.mac_type == MAC_TYPE_BMAC) {
bnx2x_update_bmac_stats(bp);
- } else if (bp->phy_flags & PHY_EMAC_FLAG) {
+ } else if (bp->link_vars.mac_type == MAC_TYPE_EMAC) {
bnx2x_update_emac_stats(bp);
} else { /* unreached */
break;
}
- bnx2x_link_reset(bp);
+ bnx2x__link_reset(bp);
/* Reset PCIE errors for debug */
REG_WR(bp, 0x2114, 0xffffffff);
bnx2x_set_mac_addr(bp);
- bnx2x_phy_init(bp);
+ bnx2x_initial_phy_init(bp);
/* Start fast path */
if (req_irq) { /* IRQ is only requested from bnx2x_open */
}
unload_error:
- bnx2x_link_reset(bp);
+ bnx2x__link_reset(bp);
if (!nomcp)
reset_code = bnx2x_fw_command(bp, reset_code);
int port = bp->port;
u32 ext_phy_type;
- bp->phy_flags = 0;
-
switch (switch_cfg) {
case SWITCH_CFG_1G:
BNX2X_DEV_INFO("switch_cfg 0x%x (1G)\n", switch_cfg);
- ext_phy_type = SERDES_EXT_PHY_TYPE(bp);
+ ext_phy_type =
+ SERDES_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
switch (ext_phy_type) {
case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
BNX2X_DEV_INFO("ext_phy_type 0x%x (Direct)\n",
BNX2X_DEV_INFO("ext_phy_type 0x%x (5482)\n",
ext_phy_type);
- bp->phy_flags |= PHY_SGMII_FLAG;
-
bp->supported |= (SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
default:
BNX2X_ERR("NVRAM config error. "
"BAD SerDes ext_phy_config 0x%x\n",
- bp->ext_phy_config);
+ bp->link_params.ext_phy_config);
return;
}
case SWITCH_CFG_10G:
BNX2X_DEV_INFO("switch_cfg 0x%x (10G)\n", switch_cfg);
- bp->phy_flags |= PHY_XGXS_FLAG;
-
- ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
+ ext_phy_type =
+ XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
switch (ext_phy_type) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
BNX2X_DEV_INFO("ext_phy_type 0x%x (Direct)\n",
SUPPORTED_Asym_Pause);
break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ BNX2X_DEV_INFO("ext_phy_type 0x%x (8073)\n",
+ ext_phy_type);
+
+ bp->supported |= (SUPPORTED_10000baseT_Full |
+ SUPPORTED_2500baseX_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause);
+ break;
+
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
BNX2X_DEV_INFO("ext_phy_type 0x%x (SFX7101)\n",
ext_phy_type);
SUPPORTED_Asym_Pause);
break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ BNX2X_ERR("XGXS PHY Failure detected 0x%x\n",
+ bp->link_params.ext_phy_config);
+ break;
+
default:
BNX2X_ERR("NVRAM config error. "
"BAD XGXS ext_phy_config 0x%x\n",
- bp->ext_phy_config);
+ bp->link_params.ext_phy_config);
return;
}
port*0x18);
BNX2X_DEV_INFO("phy_addr 0x%x\n", bp->phy_addr);
- bp->ser_lane = ((bp->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
- bp->rx_lane_swap = ((bp->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
- bp->tx_lane_swap = ((bp->lane_config &
- PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
- PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);
- BNX2X_DEV_INFO("rx_lane_swap 0x%x tx_lane_swap 0x%x\n",
- bp->rx_lane_swap, bp->tx_lane_swap);
break;
default:
bp->link_config);
return;
}
+ bp->link_params.phy_addr = bp->phy_addr;
/* mask what we support according to speed_cap_mask */
- if (!(bp->speed_cap_mask &
- PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF))
bp->supported &= ~SUPPORTED_10baseT_Half;
- if (!(bp->speed_cap_mask &
- PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL))
bp->supported &= ~SUPPORTED_10baseT_Full;
- if (!(bp->speed_cap_mask &
- PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF))
bp->supported &= ~SUPPORTED_100baseT_Half;
- if (!(bp->speed_cap_mask &
- PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL))
bp->supported &= ~SUPPORTED_100baseT_Full;
- if (!(bp->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))
bp->supported &= ~(SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full);
- if (!(bp->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G))
bp->supported &= ~SUPPORTED_2500baseX_Full;
- if (!(bp->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G))
+ if (!(bp->link_params.speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10G))
bp->supported &= ~SUPPORTED_10000baseT_Full;
BNX2X_DEV_INFO("supported 0x%x\n", bp->supported);
static void bnx2x_link_settings_requested(struct bnx2x *bp)
{
- bp->req_autoneg = 0;
- bp->req_duplex = DUPLEX_FULL;
+ bp->link_params.req_duplex = DUPLEX_FULL;
switch (bp->link_config & PORT_FEATURE_LINK_SPEED_MASK) {
case PORT_FEATURE_LINK_SPEED_AUTO:
if (bp->supported & SUPPORTED_Autoneg) {
- bp->req_autoneg |= AUTONEG_SPEED;
- bp->req_line_speed = 0;
+ bp->link_params.req_line_speed = SPEED_AUTO_NEG;
bp->advertising = bp->supported;
} else {
- if (XGXS_EXT_PHY_TYPE(bp) ==
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) {
+ u32 ext_phy_type =
+ XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
+
+ if ((ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) ||
+ (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706)) {
/* force 10G, no AN */
- bp->req_line_speed = SPEED_10000;
+ bp->link_params.req_line_speed = SPEED_10000;
bp->advertising =
(ADVERTISED_10000baseT_Full |
ADVERTISED_FIBRE);
case PORT_FEATURE_LINK_SPEED_10M_FULL:
if (bp->supported & SUPPORTED_10baseT_Full) {
- bp->req_line_speed = SPEED_10;
+ bp->link_params.req_line_speed = SPEED_10;
bp->advertising = (ADVERTISED_10baseT_Full |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_10M_HALF:
if (bp->supported & SUPPORTED_10baseT_Half) {
- bp->req_line_speed = SPEED_10;
- bp->req_duplex = DUPLEX_HALF;
+ bp->link_params.req_line_speed = SPEED_10;
+ bp->link_params.req_duplex = DUPLEX_HALF;
bp->advertising = (ADVERTISED_10baseT_Half |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_100M_FULL:
if (bp->supported & SUPPORTED_100baseT_Full) {
- bp->req_line_speed = SPEED_100;
+ bp->link_params.req_line_speed = SPEED_100;
bp->advertising = (ADVERTISED_100baseT_Full |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_100M_HALF:
if (bp->supported & SUPPORTED_100baseT_Half) {
- bp->req_line_speed = SPEED_100;
- bp->req_duplex = DUPLEX_HALF;
+ bp->link_params.req_line_speed = SPEED_100;
+ bp->link_params.req_duplex = DUPLEX_HALF;
bp->advertising = (ADVERTISED_100baseT_Half |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_1G:
if (bp->supported & SUPPORTED_1000baseT_Full) {
- bp->req_line_speed = SPEED_1000;
+ bp->link_params.req_line_speed = SPEED_1000;
bp->advertising = (ADVERTISED_1000baseT_Full |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_2_5G:
if (bp->supported & SUPPORTED_2500baseX_Full) {
- bp->req_line_speed = SPEED_2500;
+ bp->link_params.req_line_speed = SPEED_2500;
bp->advertising = (ADVERTISED_2500baseX_Full |
ADVERTISED_TP);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
case PORT_FEATURE_LINK_SPEED_10G_KX4:
case PORT_FEATURE_LINK_SPEED_10G_KR:
if (bp->supported & SUPPORTED_10000baseT_Full) {
- bp->req_line_speed = SPEED_10000;
+ bp->link_params.req_line_speed = SPEED_10000;
bp->advertising = (ADVERTISED_10000baseT_Full |
ADVERTISED_FIBRE);
} else {
BNX2X_ERR("NVRAM config error. "
"Invalid link_config 0x%x"
" speed_cap_mask 0x%x\n",
- bp->link_config, bp->speed_cap_mask);
+ bp->link_config,
+ bp->link_params.speed_cap_mask);
return;
}
break;
BNX2X_ERR("NVRAM config error. "
"BAD link speed link_config 0x%x\n",
bp->link_config);
- bp->req_autoneg |= AUTONEG_SPEED;
- bp->req_line_speed = 0;
+ bp->link_params.req_line_speed = SPEED_AUTO_NEG;
bp->advertising = bp->supported;
break;
}
- BNX2X_DEV_INFO("req_line_speed %d req_duplex %d\n",
- bp->req_line_speed, bp->req_duplex);
- bp->req_flow_ctrl = (bp->link_config &
+ bp->link_params.req_flow_ctrl = (bp->link_config &
PORT_FEATURE_FLOW_CONTROL_MASK);
- if ((bp->req_flow_ctrl == FLOW_CTRL_AUTO) &&
- (bp->supported & SUPPORTED_Autoneg))
- bp->req_autoneg |= AUTONEG_FLOW_CTRL;
+ if ((bp->link_params.req_flow_ctrl == FLOW_CTRL_AUTO) &&
+ (!bp->supported & SUPPORTED_Autoneg))
+ bp->link_params.req_flow_ctrl = FLOW_CTRL_NONE;
- BNX2X_DEV_INFO("req_autoneg 0x%x req_flow_ctrl 0x%x"
+ BNX2X_DEV_INFO("req_line_speed %d req_duplex %d req_flow_ctrl 0x%x"
" advertising 0x%x\n",
- bp->req_autoneg, bp->req_flow_ctrl, bp->advertising);
+ bp->link_params.req_line_speed,
+ bp->link_params.req_duplex,
+ bp->link_params.req_flow_ctrl, bp->advertising);
}
static void bnx2x_get_hwinfo(struct bnx2x *bp)
{
u32 val, val2, val3, val4, id;
int port = bp->port;
- u32 switch_cfg;
bp->shmem_base = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR);
BNX2X_DEV_INFO("shmem offset is %x\n", bp->shmem_base);
bp->chip_id = id;
BNX2X_DEV_INFO("chip ID is %x\n", id);
+ bp->link_params.bp = bp;
+
if (!bp->shmem_base || (bp->shmem_base != 0xAF900)) {
BNX2X_DEV_INFO("MCP not active\n");
nomcp = 1;
bp->hw_config = SHMEM_RD(bp, dev_info.shared_hw_config.config);
bp->board = SHMEM_RD(bp, dev_info.shared_hw_config.board);
- bp->serdes_config =
+ bp->link_params.serdes_config =
SHMEM_RD(bp, dev_info.port_hw_config[port].serdes_config);
- bp->lane_config =
+ bp->link_params.lane_config =
SHMEM_RD(bp, dev_info.port_hw_config[port].lane_config);
- bp->ext_phy_config =
+ bp->link_params.ext_phy_config =
SHMEM_RD(bp,
dev_info.port_hw_config[port].external_phy_config);
- bp->speed_cap_mask =
+ bp->link_params.speed_cap_mask =
SHMEM_RD(bp,
dev_info.port_hw_config[port].speed_capability_mask);
bp->link_config =
SHMEM_RD(bp, dev_info.port_feature_config[port].link_config);
- BNX2X_DEV_INFO("hw_config (%08x) board (%08x) serdes_config (%08x)\n"
- KERN_INFO " lane_config (%08x) ext_phy_config (%08x)\n"
- KERN_INFO " speed_cap_mask (%08x) link_config (%08x)"
- " fw_seq (%08x)\n",
- bp->hw_config, bp->board, bp->serdes_config,
- bp->lane_config, bp->ext_phy_config,
- bp->speed_cap_mask, bp->link_config, bp->fw_seq);
+ BNX2X_DEV_INFO("serdes_config (%08x) lane_config (%08x)\n"
+ KERN_INFO " ext_phy_config (%08x) speed_cap_mask (%08x)"
+ " link_config (%08x)\n",
+ bp->link_params.serdes_config,
+ bp->link_params.lane_config,
+ bp->link_params.ext_phy_config,
+ bp->link_params.speed_cap_mask,
+ bp->link_config);
- switch_cfg = (bp->link_config & PORT_FEATURE_CONNECTED_SWITCH_MASK);
- bnx2x_link_settings_supported(bp, switch_cfg);
-
- bp->autoneg = (bp->hw_config & SHARED_HW_CFG_AN_ENABLE_MASK);
- /* for now disable cl73 */
- bp->autoneg &= ~SHARED_HW_CFG_AN_ENABLE_CL73;
- BNX2X_DEV_INFO("autoneg 0x%x\n", bp->autoneg);
+ bp->link_params.switch_cfg = (bp->link_config &
+ PORT_FEATURE_CONNECTED_SWITCH_MASK);
+ bnx2x_link_settings_supported(bp, bp->link_params.switch_cfg);
bnx2x_link_settings_requested(bp);
bp->dev->dev_addr[3] = (u8)(val >> 16 & 0xff);
bp->dev->dev_addr[4] = (u8)(val >> 8 & 0xff);
bp->dev->dev_addr[5] = (u8)(val & 0xff);
+ memcpy(bp->link_params.mac_addr, bp->dev->dev_addr, ETH_ALEN);
+ memcpy(bp->dev->perm_addr, bp->dev->dev_addr, ETH_ALEN);
- memcpy(bp->dev->perm_addr, bp->dev->dev_addr, 6);
val = SHMEM_RD(bp, dev_info.shared_hw_config.part_num);
cmd->advertising = bp->advertising;
if (netif_carrier_ok(dev)) {
- cmd->speed = bp->line_speed;
- cmd->duplex = bp->duplex;
+ cmd->speed = bp->link_vars.line_speed;
+ cmd->duplex = bp->link_vars.duplex;
} else {
- cmd->speed = bp->req_line_speed;
- cmd->duplex = bp->req_duplex;
+ cmd->speed = bp->link_params.req_line_speed;
+ cmd->duplex = bp->link_params.req_duplex;
}
- if (bp->phy_flags & PHY_XGXS_FLAG) {
- u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp);
+ if (bp->link_params.switch_cfg == SWITCH_CFG_10G) {
+ u32 ext_phy_type =
+ XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
switch (ext_phy_type) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
cmd->port = PORT_FIBRE;
break;
cmd->port = PORT_TP;
break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ BNX2X_ERR("XGXS PHY Failure detected 0x%x\n",
+ bp->link_params.ext_phy_config);
+ break;
+
default:
DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
- bp->ext_phy_config);
+ bp->link_params.ext_phy_config);
+ break;
}
} else
cmd->port = PORT_TP;
cmd->phy_address = bp->phy_addr;
cmd->transceiver = XCVR_INTERNAL;
- if (bp->req_autoneg & AUTONEG_SPEED)
+ if (bp->link_params.req_line_speed == SPEED_AUTO_NEG)
cmd->autoneg = AUTONEG_ENABLE;
else
cmd->autoneg = AUTONEG_DISABLE;
/* advertise the requested speed and duplex if supported */
cmd->advertising &= bp->supported;
- bp->req_autoneg |= AUTONEG_SPEED;
- bp->req_line_speed = 0;
- bp->req_duplex = DUPLEX_FULL;
+ bp->link_params.req_line_speed = SPEED_AUTO_NEG;
+ bp->link_params.req_duplex = DUPLEX_FULL;
bp->advertising |= (ADVERTISED_Autoneg | cmd->advertising);
} else { /* forced speed */
return -EINVAL;
}
- bp->req_autoneg &= ~AUTONEG_SPEED;
- bp->req_line_speed = cmd->speed;
- bp->req_duplex = cmd->duplex;
+ bp->link_params.req_line_speed = cmd->speed;
+ bp->link_params.req_duplex = cmd->duplex;
bp->advertising = advertising;
}
- DP(NETIF_MSG_LINK, "req_autoneg 0x%x req_line_speed %d\n"
+ DP(NETIF_MSG_LINK, "req_line_speed %d\n"
DP_LEVEL " req_duplex %d advertising 0x%x\n",
- bp->req_autoneg, bp->req_line_speed, bp->req_duplex,
+ bp->link_params.req_line_speed, bp->link_params.req_duplex,
bp->advertising);
bnx2x_stop_stats(bp);
- bnx2x_link_initialize(bp);
+ bnx2x_link_set(bp);
return 0;
}
+#define PHY_FW_VER_LEN 10
+
static void bnx2x_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
struct bnx2x *bp = netdev_priv(dev);
+ char phy_fw_ver[PHY_FW_VER_LEN];
strcpy(info->driver, DRV_MODULE_NAME);
strcpy(info->version, DRV_MODULE_VERSION);
- snprintf(info->fw_version, 32, "%d.%d.%d:%d (BC VER %x)",
+
+ phy_fw_ver[0] = '\0';
+ bnx2x_phy_hw_lock(bp);
+ bnx2x_get_ext_phy_fw_version(&bp->link_params,
+ (bp->state != BNX2X_STATE_CLOSED),
+ phy_fw_ver, PHY_FW_VER_LEN);
+ bnx2x_phy_hw_unlock(bp);
+
+ snprintf(info->fw_version, 32, "%d.%d.%d:%d BC:%x%s%s",
BCM_5710_FW_MAJOR_VERSION, BCM_5710_FW_MINOR_VERSION,
- BCM_5710_FW_REVISION_VERSION, BCM_5710_FW_COMPILE_FLAGS,
- bp->bc_ver);
+ BCM_5710_FW_REVISION_VERSION,
+ BCM_5710_FW_COMPILE_FLAGS, bp->bc_ver,
+ ((phy_fw_ver[0] != '\0')? " PHY:":""), phy_fw_ver);
strcpy(info->bus_info, pci_name(bp->pdev));
info->n_stats = BNX2X_NUM_STATS;
info->testinfo_len = BNX2X_NUM_TESTS;
}
bnx2x_stop_stats(bp);
- bnx2x_link_initialize(bp);
+ bnx2x_link_set(bp);
return 0;
}
/* parameters already validated in ethtool_set_eeprom */
- rc = bnx2x_nvram_write(bp, eeprom->offset, eebuf, eeprom->len);
+ /* If the magic number is PHY (0x00504859) upgrade the PHY FW */
+ if (eeprom->magic == 0x00504859) {
+
+ bnx2x_phy_hw_lock(bp);
+ rc = bnx2x_flash_download(bp, bp->port,
+ bp->link_params.ext_phy_config,
+ (bp->state != BNX2X_STATE_CLOSED),
+ eebuf, eeprom->len);
+ rc |= bnx2x_link_reset(&bp->link_params,
+ &bp->link_vars);
+ rc |= bnx2x_phy_init(&bp->link_params,
+ &bp->link_vars);
+ bnx2x_phy_hw_unlock(bp);
+
+ } else
+ rc = bnx2x_nvram_write(bp, eeprom->offset, eebuf, eeprom->len);
return rc;
}
{
struct bnx2x *bp = netdev_priv(dev);
- epause->autoneg =
- ((bp->req_autoneg & AUTONEG_FLOW_CTRL) == AUTONEG_FLOW_CTRL);
- epause->rx_pause = ((bp->flow_ctrl & FLOW_CTRL_RX) == FLOW_CTRL_RX);
- epause->tx_pause = ((bp->flow_ctrl & FLOW_CTRL_TX) == FLOW_CTRL_TX);
+ epause->autoneg = (bp->link_params.req_flow_ctrl == FLOW_CTRL_AUTO) &&
+ (bp->link_params.req_line_speed == SPEED_AUTO_NEG);
+
+ epause->rx_pause = ((bp->link_vars.flow_ctrl & FLOW_CTRL_RX) ==
+ FLOW_CTRL_RX);
+ epause->tx_pause = ((bp->link_vars.flow_ctrl & FLOW_CTRL_TX) ==
+ FLOW_CTRL_TX);
DP(NETIF_MSG_LINK, "ethtool_pauseparam: cmd %d\n"
DP_LEVEL " autoneg %d rx_pause %d tx_pause %d\n",
DP_LEVEL " autoneg %d rx_pause %d tx_pause %d\n",
epause->cmd, epause->autoneg, epause->rx_pause, epause->tx_pause);
- if (epause->autoneg) {
- if (!(bp->supported & SUPPORTED_Autoneg)) {
- DP(NETIF_MSG_LINK, "Aotoneg not supported\n");
- return -EINVAL;
- }
-
- bp->req_autoneg |= AUTONEG_FLOW_CTRL;
- } else
- bp->req_autoneg &= ~AUTONEG_FLOW_CTRL;
-
- bp->req_flow_ctrl = FLOW_CTRL_AUTO;
+ bp->link_params.req_flow_ctrl = FLOW_CTRL_AUTO;
if (epause->rx_pause)
- bp->req_flow_ctrl |= FLOW_CTRL_RX;
+ bp->link_params.req_flow_ctrl |= FLOW_CTRL_RX;
+
if (epause->tx_pause)
- bp->req_flow_ctrl |= FLOW_CTRL_TX;
+ bp->link_params.req_flow_ctrl |= FLOW_CTRL_TX;
+
+ if (bp->link_params.req_flow_ctrl == FLOW_CTRL_AUTO)
+ bp->link_params.req_flow_ctrl = FLOW_CTRL_NONE;
- if (!(bp->req_autoneg & AUTONEG_FLOW_CTRL) &&
- (bp->req_flow_ctrl == FLOW_CTRL_AUTO))
- bp->req_flow_ctrl = FLOW_CTRL_NONE;
+ if (epause->autoneg) {
+ if (!(bp->supported & SUPPORTED_Autoneg)) {
+ DP(NETIF_MSG_LINK, "Autoneg not supported\n");
+ return -EINVAL;
+ }
- DP(NETIF_MSG_LINK, "req_autoneg 0x%x req_flow_ctrl 0x%x\n",
- bp->req_autoneg, bp->req_flow_ctrl);
+ if (bp->link_params.req_line_speed == SPEED_AUTO_NEG)
+ bp->link_params.req_flow_ctrl = FLOW_CTRL_AUTO;
+ }
+ DP(NETIF_MSG_LINK,
+ "req_flow_ctrl 0x%x\n", bp->link_params.req_flow_ctrl);
bnx2x_stop_stats(bp);
- bnx2x_link_initialize(bp);
+ bnx2x_link_set(bp);
return 0;
}
data = 2;
for (i = 0; i < (data * 2); i++) {
- if ((i % 2) == 0) {
- bnx2x_leds_set(bp, SPEED_1000);
- } else {
- bnx2x_leds_unset(bp);
- }
+ if ((i % 2) == 0)
+ bnx2x_set_led(bp, bp->port, LED_MODE_OPER, SPEED_1000,
+ bp->link_params.hw_led_mode,
+ bp->link_params.chip_id);
+ else
+ bnx2x_set_led(bp, bp->port, LED_MODE_OFF, 0,
+ bp->link_params.hw_led_mode,
+ bp->link_params.chip_id);
+
msleep_interruptible(500);
if (signal_pending(current))
break;
}
- if (bp->link_up)
- bnx2x_leds_set(bp, bp->line_speed);
+ if (bp->link_vars.link_up)
+ bnx2x_set_led(bp, bp->port, LED_MODE_OPER,
+ bp->link_vars.line_speed,
+ bp->link_params.hw_led_mode,
+ bp->link_params.chip_id);
return 0;
}
return 0;
}
-/* Called with rtnl_lock */
+/* called with rtnl_lock */
static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
struct mii_ioctl_data *data = if_mii(ifr);
data->phy_id = bp->phy_addr;
/* fallthrough */
+
case SIOCGMIIREG: {
- u32 mii_regval;
+ u16 mii_regval;
- spin_lock_bh(&bp->phy_lock);
- if (bp->state == BNX2X_STATE_OPEN) {
- err = bnx2x_mdio22_read(bp, data->reg_num & 0x1f,
- &mii_regval);
+ if (!netif_running(dev))
+ return -EAGAIN;
- data->val_out = mii_regval;
- } else {
- err = -EAGAIN;
- }
- spin_unlock_bh(&bp->phy_lock);
+ mutex_lock(&bp->phy_mutex);
+ err = bnx2x_cl45_read(bp, bp->port, 0, bp->phy_addr,
+ DEFAULT_PHY_DEV_ADDR,
+ (data->reg_num & 0x1f), &mii_regval);
+ data->val_out = mii_regval;
+ mutex_unlock(&bp->phy_mutex);
return err;
}
if (!capable(CAP_NET_ADMIN))
return -EPERM;
- spin_lock_bh(&bp->phy_lock);
- if (bp->state == BNX2X_STATE_OPEN) {
- err = bnx2x_mdio22_write(bp, data->reg_num & 0x1f,
- data->val_in);
- } else {
- err = -EAGAIN;
- }
- spin_unlock_bh(&bp->phy_lock);
+ if (!netif_running(dev))
+ return -EAGAIN;
+
+ mutex_lock(&bp->phy_mutex);
+ err = bnx2x_cl45_write(bp, bp->port, 0, bp->phy_addr,
+ DEFAULT_PHY_DEV_ADDR,
+ (data->reg_num & 0x1f), data->val_in);
+ mutex_unlock(&bp->phy_mutex);
return err;
default:
bp->dev = dev;
bp->pdev = pdev;
- spin_lock_init(&bp->phy_lock);
-
INIT_WORK(&bp->reset_task, bnx2x_reset_task);
INIT_WORK(&bp->sp_task, bnx2x_sp_task);
#define CCM_REG_CCM_INT_MASK 0xd01e4
/* [R 11] Interrupt register #0 read */
#define CCM_REG_CCM_INT_STS 0xd01d8
+/* [R 27] Parity register #0 read */
+#define CCM_REG_CCM_PRTY_STS 0xd01e8
/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define CCM_REG_PBF_WEIGHT 0xd00ac
-/* [RW 6] The physical queue number of queue number 1 per port index. */
#define CCM_REG_PHYS_QNUM1_0 0xd0134
#define CCM_REG_PHYS_QNUM1_1 0xd0138
-/* [RW 6] The physical queue number of queue number 2 per port index. */
#define CCM_REG_PHYS_QNUM2_0 0xd013c
#define CCM_REG_PHYS_QNUM2_1 0xd0140
-/* [RW 6] The physical queue number of queue number 3 per port index. */
#define CCM_REG_PHYS_QNUM3_0 0xd0144
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 0 port
- index 0. */
+#define CCM_REG_PHYS_QNUM3_1 0xd0148
#define CCM_REG_QOS_PHYS_QNUM0_0 0xd0114
#define CCM_REG_QOS_PHYS_QNUM0_1 0xd0118
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 1 port
- index 0. */
#define CCM_REG_QOS_PHYS_QNUM1_0 0xd011c
#define CCM_REG_QOS_PHYS_QNUM1_1 0xd0120
-/* [RW 6] The physical queue number of queue number 0 with QOS equal 2 port
- index 0. */
#define CCM_REG_QOS_PHYS_QNUM2_0 0xd0124
+#define CCM_REG_QOS_PHYS_QNUM2_1 0xd0128
+#define CCM_REG_QOS_PHYS_QNUM3_0 0xd012c
+#define CCM_REG_QOS_PHYS_QNUM3_1 0xd0130
/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
mechanism. The fields are: [5:0] - message length; [12:6] - message
pointer; 18:13] - next pointer. */
#define CCM_REG_XX_DESCR_TABLE 0xd0300
+#define CCM_REG_XX_DESCR_TABLE_SIZE 36
/* [R 7] Used to read the value of XX protection Free counter. */
#define CCM_REG_XX_FREE 0xd0184
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
/* [WB 24] MATT ram access. each entry has the following
format:{RegionLength[11:0]; egionOffset[11:0]} */
#define CDU_REG_MATT 0x101100
+/* [RW 1] when this bit is set the CDU operates in e1hmf mode */
+#define CDU_REG_MF_MODE 0x101050
/* [R 1] indication the initializing the activity counter by the hardware
was done. */
#define CFC_REG_AC_INIT_DONE 0x104078
field allows changing the priorities of the weighted-round-robin arbiter
which selects which CFC load client should be served next */
#define CFC_REG_LCREQ_WEIGHTS 0x104084
+/* [RW 16] Link List ram access; data = {prev_lcid; ext_lcid} */
+#define CFC_REG_LINK_LIST 0x104c00
+#define CFC_REG_LINK_LIST_SIZE 256
/* [R 1] indication the initializing the link list by the hardware was done. */
#define CFC_REG_LL_INIT_DONE 0x104074
/* [R 9] Number of allocated LCIDs which are at empty state */
#define CFC_REG_NUM_LCIDS_LEAVING 0x104018
/* [RW 8] The event id for aggregated interrupt 0 */
#define CSDM_REG_AGG_INT_EVENT_0 0xc2038
+#define CSDM_REG_AGG_INT_EVENT_1 0xc203c
+#define CSDM_REG_AGG_INT_EVENT_10 0xc2060
+#define CSDM_REG_AGG_INT_EVENT_11 0xc2064
+#define CSDM_REG_AGG_INT_EVENT_12 0xc2068
+#define CSDM_REG_AGG_INT_EVENT_13 0xc206c
+#define CSDM_REG_AGG_INT_EVENT_14 0xc2070
+#define CSDM_REG_AGG_INT_EVENT_15 0xc2074
+#define CSDM_REG_AGG_INT_EVENT_16 0xc2078
+#define CSDM_REG_AGG_INT_EVENT_17 0xc207c
+#define CSDM_REG_AGG_INT_EVENT_18 0xc2080
+#define CSDM_REG_AGG_INT_EVENT_19 0xc2084
+#define CSDM_REG_AGG_INT_EVENT_2 0xc2040
+#define CSDM_REG_AGG_INT_EVENT_20 0xc2088
+#define CSDM_REG_AGG_INT_EVENT_21 0xc208c
+#define CSDM_REG_AGG_INT_EVENT_22 0xc2090
+#define CSDM_REG_AGG_INT_EVENT_23 0xc2094
+#define CSDM_REG_AGG_INT_EVENT_24 0xc2098
+#define CSDM_REG_AGG_INT_EVENT_25 0xc209c
+#define CSDM_REG_AGG_INT_EVENT_26 0xc20a0
+#define CSDM_REG_AGG_INT_EVENT_27 0xc20a4
+#define CSDM_REG_AGG_INT_EVENT_28 0xc20a8
+#define CSDM_REG_AGG_INT_EVENT_29 0xc20ac
+#define CSDM_REG_AGG_INT_EVENT_3 0xc2044
+#define CSDM_REG_AGG_INT_EVENT_30 0xc20b0
+#define CSDM_REG_AGG_INT_EVENT_31 0xc20b4
+#define CSDM_REG_AGG_INT_EVENT_4 0xc2048
+/* [RW 1] The T bit for aggregated interrupt 0 */
+#define CSDM_REG_AGG_INT_T_0 0xc20b8
+#define CSDM_REG_AGG_INT_T_1 0xc20bc
+#define CSDM_REG_AGG_INT_T_10 0xc20e0
+#define CSDM_REG_AGG_INT_T_11 0xc20e4
+#define CSDM_REG_AGG_INT_T_12 0xc20e8
+#define CSDM_REG_AGG_INT_T_13 0xc20ec
+#define CSDM_REG_AGG_INT_T_14 0xc20f0
+#define CSDM_REG_AGG_INT_T_15 0xc20f4
+#define CSDM_REG_AGG_INT_T_16 0xc20f8
+#define CSDM_REG_AGG_INT_T_17 0xc20fc
+#define CSDM_REG_AGG_INT_T_18 0xc2100
+#define CSDM_REG_AGG_INT_T_19 0xc2104
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define CSDM_REG_CFC_RSP_START_ADDR 0xc2008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define CSDM_REG_CSDM_INT_MASK_0 0xc229c
#define CSDM_REG_CSDM_INT_MASK_1 0xc22ac
+/* [R 32] Interrupt register #0 read */
+#define CSDM_REG_CSDM_INT_STS_0 0xc2290
+#define CSDM_REG_CSDM_INT_STS_1 0xc22a0
/* [RW 11] Parity mask register #0 read/write */
#define CSDM_REG_CSDM_PRTY_MASK 0xc22bc
/* [R 11] Parity register #0 read */
/* [RW 32] Interrupt mask register #0 read/write */
#define CSEM_REG_CSEM_INT_MASK_0 0x200110
#define CSEM_REG_CSEM_INT_MASK_1 0x200120
+/* [R 32] Interrupt register #0 read */
+#define CSEM_REG_CSEM_INT_STS_0 0x200104
+#define CSEM_REG_CSEM_INT_STS_1 0x200114
/* [RW 32] Parity mask register #0 read/write */
#define CSEM_REG_CSEM_PRTY_MASK_0 0x200130
#define CSEM_REG_CSEM_PRTY_MASK_1 0x200140
#define CSEM_REG_ENABLE_OUT 0x2000a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- CSEM_REGISTERS_FAST_MEMORY (Offset: 0x220000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define CSEM_REG_FAST_MEMORY 0x220000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define CSEM_REG_INT_TABLE 0x200400
+#define CSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define CSEM_REG_MSG_NUM_FIC0 0x200000
#define DORQ_REG_AGG_CMD3 0x17006c
/* [RW 28] UCM Header. */
#define DORQ_REG_CMHEAD_RX 0x170050
+/* [RW 32] Doorbell address for RBC doorbells (function 0). */
+#define DORQ_REG_DB_ADDR0 0x17008c
/* [RW 5] Interrupt mask register #0 read/write */
#define DORQ_REG_DORQ_INT_MASK 0x170180
/* [R 5] Interrupt register #0 read */
#define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1)
#define HC_REG_AGG_INT_0 0x108050
#define HC_REG_AGG_INT_1 0x108054
-/* [RW 16] attention bit and attention acknowledge bits status for port 0
- and 1 according to the following address map: addr 0 - attn_bit_0; addr 1
- - attn_ack_bit_0; addr 2 - attn_bit_1; addr 3 - attn_ack_bit_1; */
#define HC_REG_ATTN_BIT 0x108120
-/* [RW 16] attn bits status index for attn bit msg; addr 0 - function 0;
- addr 1 - functin 1 */
#define HC_REG_ATTN_IDX 0x108100
-/* [RW 32] port 0 lower 32 bits address field for attn messag. */
#define HC_REG_ATTN_MSG0_ADDR_L 0x108018
-/* [RW 32] port 1 lower 32 bits address field for attn messag. */
#define HC_REG_ATTN_MSG1_ADDR_L 0x108020
-/* [RW 8] status block number for attn bit msg - function 0; */
#define HC_REG_ATTN_NUM_P0 0x108038
-/* [RW 8] status block number for attn bit msg - function 1 */
#define HC_REG_ATTN_NUM_P1 0x10803c
#define HC_REG_CONFIG_0 0x108000
#define HC_REG_CONFIG_1 0x108004
+#define HC_REG_FUNC_NUM_P0 0x1080ac
+#define HC_REG_FUNC_NUM_P1 0x1080b0
/* [RW 3] Parity mask register #0 read/write */
#define HC_REG_HC_PRTY_MASK 0x1080a0
/* [R 3] Parity register #0 read */
#define HC_REG_HC_PRTY_STS 0x108094
-/* [RW 17] status block interrupt mask; one in each bit means unmask; zerow
- in each bit means mask; bit 0 - default SB; bit 1 - SB_0; bit 2 - SB_1...
- bit 16- SB_15; addr 0 - port 0; addr 1 - port 1 */
#define HC_REG_INT_MASK 0x108108
-/* [RW 16] port 0 attn bit condition monitoring; each bit that is set will
- lock a change fron 0 to 1 in the corresponding attention signals that
- comes from the AEU */
#define HC_REG_LEADING_EDGE_0 0x108040
#define HC_REG_LEADING_EDGE_1 0x108048
-/* [RW 16] all producer and consumer of port 0 according to the following
- addresses; U_prod: 0-15; C_prod: 16-31; U_cons: 32-47; C_cons:48-63;
- Defoult_prod: U/C/X/T/Attn-64/65/66/67/68; Defoult_cons:
- U/C/X/T/Attn-69/70/71/72/73 */
#define HC_REG_P0_PROD_CONS 0x108200
-/* [RW 16] all producer and consumer of port 1according to the following
- addresses; U_prod: 0-15; C_prod: 16-31; U_cons: 32-47; C_cons:48-63;
- Defoult_prod: U/C/X/T/Attn-64/65/66/67/68; Defoult_cons:
- U/C/X/T/Attn-69/70/71/72/73 */
#define HC_REG_P1_PROD_CONS 0x108400
-/* [W 1] This register is write only and has 4 addresses as follow: 0 =
- clear all PBA bits port 0; 1 = clear all pending interrupts request
- port0; 2 = clear all PBA bits port 1; 3 = clear all pending interrupts
- request port1; here is no meaning for the data in this register */
#define HC_REG_PBA_COMMAND 0x108140
#define HC_REG_PCI_CONFIG_0 0x108010
#define HC_REG_PCI_CONFIG_1 0x108014
-/* [RW 24] all counters acording to the following address: LSB: 0=read; 1=
- read_clear; 0-71 = HW counters (the inside order is the same as the
- interrupt table in the spec); 72-219 = SW counters 1 (stops after first
- consumer upd) the inside order is: 72-103 - U_non_default_p0; 104-135
- C_non_defaul_p0; 36-145 U/C/X/T/Attn_default_p0; 146-177
- U_non_default_p1; 178-209 C_non_defaul_p1; 10-219 U/C/X/T/Attn_default_p1
- ; 220-367 = SW counters 2 (stops when prod=cons) the inside order is:
- 220-251 - U_non_default_p0; 252-283 C_non_defaul_p0; 84-293
- U/C/X/T/Attn_default_p0; 294-325 U_non_default_p1; 326-357
- C_non_defaul_p1; 58-367 U/C/X/T/Attn_default_p1 ; 368-515 = mailbox
- counters; (the inside order of the mailbox counter is 368-431 U and C
- non_default_p0; 432-441 U/C/X/T/Attn_default_p0; 442-505 U and C
- non_default_p1; 506-515 U/C/X/T/Attn_default_p1) */
#define HC_REG_STATISTIC_COUNTERS 0x109000
-/* [RW 16] port 0 attn bit condition monitoring; each bit that is set will
- lock a change fron 1 to 0 in the corresponding attention signals that
- comes from the AEU */
#define HC_REG_TRAILING_EDGE_0 0x108044
#define HC_REG_TRAILING_EDGE_1 0x10804c
#define HC_REG_UC_RAM_ADDR_0 0x108028
#define HC_REG_UC_RAM_ADDR_1 0x108030
-/* [RW 16] ustorm address for coalesc now message */
#define HC_REG_USTORM_ADDR_FOR_COALESCE 0x108068
#define HC_REG_VQID_0 0x108008
#define HC_REG_VQID_1 0x10800c
rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP Latched
ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_AFTER_INVERT_4_MCP 0xa458
-/* [W 11] write to this register results with the clear of the latched
+/* [W 14] write to this register results with the clear of the latched
signals; one in d0 clears RBCR latch; one in d1 clears RBCT latch; one in
d2 clears RBCN latch; one in d3 clears RBCU latch; one in d4 clears RBCP
latch; one in d5 clears GRC Latched timeout attention; one in d6 clears
GRC Latched reserved access attention; one in d7 clears Latched
rom_parity; one in d8 clears Latched ump_rx_parity; one in d9 clears
- Latched ump_tx_parity; one in d10 clears Latched scpad_parity; read from
- this register return zero */
+ Latched ump_tx_parity; one in d10 clears Latched scpad_parity (both
+ ports); one in d11 clears pxpv_misc_mps_attn; one in d12 clears
+ pxp_misc_exp_rom_attn0; one in d13 clears pxp_misc_exp_rom_attn1; read
+ from this register return zero */
#define MISC_REG_AEU_CLR_LATCH_SIGNAL 0xa45c
/* [RW 32] first 32b for enabling the output for function 0 output0. mapped
as follows: [0] NIG attention for function0; [1] NIG attention for
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0 0xa06c
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1 0xa07c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_2 0xa08c
#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3 0xa09c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_5 0xa0bc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_6 0xa0cc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_7 0xa0dc
/* [RW 32] first 32b for enabling the output for function 1 output0. mapped
as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 1; [3] GPIO2 function 1; [4] GPIO3 function
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 0xa10c
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1 0xa11c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_2 0xa12c
#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3 0xa13c
-/* [RW 32] first 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] NIG attention for function0; [1] NIG attention for
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_5 0xa15c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_6 0xa16c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_7 0xa17c
+/* [RW 32] first 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
#define MISC_REG_AEU_ENABLE1_NIG_0 0xa0ec
#define MISC_REG_AEU_ENABLE1_NIG_1 0xa18c
-/* [RW 32] first 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] NIG attention for function0; [1] NIG attention for
+/* [RW 32] first 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
interrupt; */
#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0 0xa110
#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_1 0xa120
-/* [RW 32] second 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt;
- [2] QM Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5]
- Timers Hw interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8]
- XCM Parity error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11]
- XSEMI Hw interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw
- interrupt; [14] NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI
- core Parity error; [17] Vaux PCI core Hw interrupt; [18] Debug Parity
- error; [19] Debug Hw interrupt; [20] USDM Parity error; [21] USDM Hw
- interrupt; [22] UCM Parity error; [23] UCM Hw interrupt; [24] USEMI
- Parity error; [25] USEMI Hw interrupt; [26] UPB Parity error; [27] UPB Hw
- interrupt; [28] CSDM Parity error; [29] CSDM Hw interrupt; [30] CCM
- Parity error; [31] CCM Hw interrupt; */
+/* [RW 32] second 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
#define MISC_REG_AEU_ENABLE2_NIG_0 0xa0f0
#define MISC_REG_AEU_ENABLE2_NIG_1 0xa190
-/* [RW 32] second 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt;
- [2] QM Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5]
- Timers Hw interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8]
- XCM Parity error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11]
- XSEMI Hw interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw
- interrupt; [14] NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI
- core Parity error; [17] Vaux PCI core Hw interrupt; [18] Debug Parity
- error; [19] Debug Hw interrupt; [20] USDM Parity error; [21] USDM Hw
- interrupt; [22] UCM Parity error; [23] UCM Hw interrupt; [24] USEMI
- Parity error; [25] USEMI Hw interrupt; [26] UPB Parity error; [27] UPB Hw
- interrupt; [28] CSDM Parity error; [29] CSDM Hw interrupt; [30] CCM
- Parity error; [31] CCM Hw interrupt; */
+/* [RW 32] second 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
#define MISC_REG_AEU_ENABLE2_PXP_0 0xa100
#define MISC_REG_AEU_ENABLE2_PXP_1 0xa1a0
/* [RW 32] third 32b for enabling the output for function 0 output0. mapped
attn1; */
#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_0 0xa114
#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_1 0xa124
-/* [RW 32] third 32b for enabling the output for close the gate nig 0.
- mapped as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2]
- PXP Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity
- error; [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC
- Hw interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE
- Parity error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13]
- IGU (HC) Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt;
- [16] pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0;
- [20] MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0;
- [23] SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST;
- [26] SW timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers
- attn_3 func1; [29] SW timers attn_4 func1; [30] General attn0; [31]
- General attn1; */
+/* [RW 32] third 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
#define MISC_REG_AEU_ENABLE3_NIG_0 0xa0f4
#define MISC_REG_AEU_ENABLE3_NIG_1 0xa194
-/* [RW 32] third 32b for enabling the output for close the gate pxp 0.
- mapped as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2]
- PXP Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity
- error; [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC
- Hw interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE
- Parity error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13]
- IGU (HC) Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt;
- [16] pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0;
- [20] MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0;
- [23] SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST;
- [26] SW timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers
- attn_3 func1; [29] SW timers attn_4 func1; [30] General attn0; [31]
- General attn1; */
+/* [RW 32] third 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
#define MISC_REG_AEU_ENABLE3_PXP_0 0xa104
#define MISC_REG_AEU_ENABLE3_PXP_1 0xa1a4
/* [RW 32] fourth 32b for enabling the output for function 0 output0.mapped
Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0 0xa078
#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_2 0xa098
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_4 0xa0b8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_5 0xa0c8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_6 0xa0d8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_7 0xa0e8
/* [RW 32] fourth 32b for enabling the output for function 1 output0.mapped
as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0 0xa118
#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_2 0xa138
-/* [RW 32] fourth 32b for enabling the output for close the gate nig
- 0.mapped as follows: [0] General attn2; [1] General attn3; [2] General
- attn4; [3] General attn5; [4] General attn6; [5] General attn7; [6]
- General attn8; [7] General attn9; [8] General attn10; [9] General attn11;
- [10] General attn12; [11] General attn13; [12] General attn14; [13]
- General attn15; [14] General attn16; [15] General attn17; [16] General
- attn18; [17] General attn19; [18] General attn20; [19] General attn21;
- [20] Main power interrupt; [21] RBCR Latched attn; [22] RBCT Latched
- attn; [23] RBCN Latched attn; [24] RBCU Latched attn; [25] RBCP Latched
- attn; [26] GRC Latched timeout attention; [27] GRC Latched reserved
- access attention; [28] MCP Latched rom_parity; [29] MCP Latched
- ump_rx_parity; [30] MCP Latched ump_tx_parity; [31] MCP Latched
- scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_4 0xa158
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_5 0xa168
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_6 0xa178
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_7 0xa188
+/* [RW 32] fourth 32b for enabling the output for close the gate nig.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_NIG_0 0xa0f8
#define MISC_REG_AEU_ENABLE4_NIG_1 0xa198
-/* [RW 32] fourth 32b for enabling the output for close the gate pxp
- 0.mapped as follows: [0] General attn2; [1] General attn3; [2] General
- attn4; [3] General attn5; [4] General attn6; [5] General attn7; [6]
- General attn8; [7] General attn9; [8] General attn10; [9] General attn11;
- [10] General attn12; [11] General attn13; [12] General attn14; [13]
- General attn15; [14] General attn16; [15] General attn17; [16] General
- attn18; [17] General attn19; [18] General attn20; [19] General attn21;
- [20] Main power interrupt; [21] RBCR Latched attn; [22] RBCT Latched
- attn; [23] RBCN Latched attn; [24] RBCU Latched attn; [25] RBCP Latched
- attn; [26] GRC Latched timeout attention; [27] GRC Latched reserved
- access attention; [28] MCP Latched rom_parity; [29] MCP Latched
- ump_rx_parity; [30] MCP Latched ump_tx_parity; [31] MCP Latched
- scpad_parity; */
+/* [RW 32] fourth 32b for enabling the output for close the gate pxp.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
#define MISC_REG_AEU_ENABLE4_PXP_0 0xa108
#define MISC_REG_AEU_ENABLE4_PXP_1 0xa1a8
/* [RW 1] set/clr general attention 0; this will set/clr bit 94 in the aeu
#define MISC_REG_AEU_GENERAL_ATTN_19 0xa04c
#define MISC_REG_AEU_GENERAL_ATTN_10 0xa028
#define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c
+#define MISC_REG_AEU_GENERAL_ATTN_12 0xa030
#define MISC_REG_AEU_GENERAL_ATTN_2 0xa008
#define MISC_REG_AEU_GENERAL_ATTN_20 0xa050
#define MISC_REG_AEU_GENERAL_ATTN_21 0xa054
#define MISC_REG_AEU_GENERAL_ATTN_7 0xa01c
#define MISC_REG_AEU_GENERAL_ATTN_8 0xa020
#define MISC_REG_AEU_GENERAL_ATTN_9 0xa024
+#define MISC_REG_AEU_GENERAL_MASK 0xa61c
/* [RW 32] first 32b for inverting the input for function 0; for each bit:
0= do not invert; 1= invert; mapped as follows: [0] NIG attention for
function0; [1] NIG attention for function1; [2] GPIO1 mcp; [3] GPIO2 mcp;
#define MISC_REG_AEU_INVERTER_2_FUNC_0 0xa230
#define MISC_REG_AEU_INVERTER_2_FUNC_1 0xa240
/* [RW 10] [7:0] = mask 8 attention output signals toward IGU function0;
- [9:8] = mask close the gates signals of function 0 toward PXP [8] and NIG
- [9]. Zero = mask; one = unmask */
+ [9:8] = raserved. Zero = mask; one = unmask */
#define MISC_REG_AEU_MASK_ATTN_FUNC_0 0xa060
#define MISC_REG_AEU_MASK_ATTN_FUNC_1 0xa064
+/* [RW 1] If set a system kill occurred */
+#define MISC_REG_AEU_SYS_KILL_OCCURRED 0xa610
+/* [RW 32] Represent the status of the input vector to the AEU when a system
+ kill occurred. The register is reset in por reset. Mapped as follows: [0]
+ NIG attention for function0; [1] NIG attention for function1; [2] GPIO1
+ mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1;
+ [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10]
+ PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event
+ function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP
+ Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for
+ mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19]
+ BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC
+ Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw
+ interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI
+ Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw
+ interrupt; */
+#define MISC_REG_AEU_SYS_KILL_STATUS_0 0xa600
+#define MISC_REG_AEU_SYS_KILL_STATUS_1 0xa604
+#define MISC_REG_AEU_SYS_KILL_STATUS_2 0xa608
+#define MISC_REG_AEU_SYS_KILL_STATUS_3 0xa60c
/* [R 4] This field indicates the type of the device. '0' - 2 Ports; '1' - 1
Port. */
#define MISC_REG_BOND_ID 0xa400
starts at 0x0 for the A0 tape-out and increments by one for each
all-layer tape-out. */
#define MISC_REG_CHIP_REV 0xa40c
-/* [RW 32] The following driver registers(1..6) represent 6 drivers and 32
- clients. Each client can be controlled by one driver only. One in each
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_10 0xa3e0
+#define MISC_REG_DRIVER_CONTROL_10_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_11 0xa3e8
+#define MISC_REG_DRIVER_CONTROL_11_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_12 0xa3f0
+#define MISC_REG_DRIVER_CONTROL_12_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_13 0xa3f8
+#define MISC_REG_DRIVER_CONTROL_13_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
bit represent that this driver control the appropriate client (Ex: bit 5
is set means this driver control client number 5). addr1 = set; addr0 =
clear; read from both addresses will give the same result = status. write
it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
be asserted). */
#define MISC_REG_DRIVER_CONTROL_1 0xa510
+#define MISC_REG_DRIVER_CONTROL_14 0xa5e0
+#define MISC_REG_DRIVER_CONTROL_14_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_15 0xa5e8
+#define MISC_REG_DRIVER_CONTROL_15_SIZE 2
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_16 0xa5f0
+#define MISC_REG_DRIVER_CONTROL_16_SIZE 2
+/* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0
+ only. */
+#define MISC_REG_E1HMF_MODE 0xa5f8
/* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of
these bits is written as a '1'; the corresponding SPIO bit will turn off
it's drivers and become an input. This is the reset state of all GPIO
This is the result value of the pin; not the drive value. Writing these
bits will have not effect. */
#define MISC_REG_GPIO 0xa490
+/* [R 28] this field hold the last information that caused reserved
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master thatcaused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_RSV_ATTN 0xa3c0
+/* [R 28] this field hold the last information that caused timeout
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master thatcaused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4
/* [RW 1] Setting this bit enables a timer in the GRC block to timeout any
access that does not finish within
~misc_registers_grc_timout_val.grc_timeout_val cycles. When this bit is
#define MISC_REG_MISC_PRTY_MASK 0xa398
/* [R 1] Parity register #0 read */
#define MISC_REG_MISC_PRTY_STS 0xa38c
+#define MISC_REG_NIG_WOL_P0 0xa270
+#define MISC_REG_NIG_WOL_P1 0xa274
+/* [R 1] If set indicate that the pcie_rst_b was asserted without perst
+ assertion */
+#define MISC_REG_PCIE_HOT_RESET 0xa618
/* [RW 32] 32 LSB of storm PLL first register; reset val = 0x 071d2911.
inside order of the bits is: [0] P1 divider[0] (reset value 1); [1] P1
divider[1] (reset value 0); [2] P1 divider[2] (reset value 0); [3] P1
#define MISC_REG_PLL_STORM_CTRL_2 0xa298
#define MISC_REG_PLL_STORM_CTRL_3 0xa29c
#define MISC_REG_PLL_STORM_CTRL_4 0xa2a0
-/* [RW 32] reset reg#1; rite/read one = the specific block is out of reset;
+/* [RW 32] reset reg#2; rite/read one = the specific block is out of reset;
write/read zero = the specific block is in reset; addr 0-wr- the write
value will be written to the register; addr 1-set - one will be written
to all the bits that have the value of one in the data written (bits that
written to all the bits that have the value of one in the data written
(bits that have the value of zero will not be change); addr 3-ignore;
read ignore from all addr except addr 00; inside order of the bits is:
- [0] rst_brb1; [1] rst_prs; [2] rst_src; [3] rst_tsdm; [4] rst_tsem; [5]
- rst_tcm; [6] rst_rbcr; [7] rst_nig; [8] rst_usdm; [9] rst_ucm; [10]
- rst_usem; [11] rst_upb; [12] rst_ccm; [13] rst_csem; [14] rst_csdm; [15]
- rst_rbcu; [16] rst_pbf; [17] rst_qm; [18] rst_tm; [19] rst_dorq; [20]
- rst_xcm; [21] rst_xsdm; [22] rst_xsem; [23] rst_rbct; [24] rst_cdu; [25]
- rst_cfc; [26] rst_pxp; [27] rst_pxpv; [28] rst_rbcp; [29] rst_hc; [30]
- rst_dmae; [31] rst_semi_rtc; */
-#define MISC_REG_RESET_REG_1 0xa580
+ [0] rst_bmac0; [1] rst_bmac1; [2] rst_emac0; [3] rst_emac1; [4] rst_grc;
+ [5] rst_mcp_n_reset_reg_hard_core; [6] rst_ mcp_n_hard_core_rst_b; [7]
+ rst_ mcp_n_reset_cmn_cpu; [8] rst_ mcp_n_reset_cmn_core; [9] rst_rbcn;
+ [10] rst_dbg; [11] rst_misc_core; [12] rst_dbue (UART); [13]
+ Pci_resetmdio_n; [14] rst_emac0_hard_core; [15] rst_emac1_hard_core; 16]
+ rst_pxp_rq_rd_wr; 31:17] reserved */
#define MISC_REG_RESET_REG_2 0xa590
/* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is
shared with the driver resides */
select VAUX supply. (This is an output pin only; it is not controlled by
the SET and CLR fields; it is controlled by the Main Power SM; the FLOAT
field is not applicable for this pin; only the VALUE fields is relevant -
- it reflects the output value); [3] reserved; [4] spio_4; [5] spio_5; [6]
+ it reflects the output value); [3] port swap [4] spio_4; [5] spio_5; [6]
Bit 0 of UMP device ID select; read by UMP firmware; [7] Bit 1 of UMP
device ID select; read by UMP firmware. */
#define MISC_REG_SPIO 0xa4fc
#define NIG_REG_BRB1_PAUSE_IN_EN 0x100c8
/* [RW 1] output enable for RX BRB1 LP IF */
#define NIG_REG_BRB_LB_OUT_EN 0x10100
-/* [WB_W 72] Debug packet to LP from RBC; Data spelling:[63:0] data; 64]
- error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush */
+/* [WB_W 82] Debug packet to LP from RBC; Data spelling:[63:0] data; 64]
+ error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush;
+ 72:73]-vnic_num; 81:74]-sideband_info */
#define NIG_REG_DEBUG_PACKET_LB 0x10800
/* [RW 1] Input enable for TX Debug packet */
#define NIG_REG_EGRESS_DEBUG_IN_EN 0x100dc
/* [RW 1] MAC configuration for packets of port0. If 1 - all packet outputs
to emac for port0; other way to bmac for port0 */
#define NIG_REG_EGRESS_EMAC0_PORT 0x10058
+/* [RW 32] TX_MNG_FIFO in NIG_TX_PORT0; data[31:0] written in FIFO order. */
+#define NIG_REG_EGRESS_MNG0_FIFO 0x1045c
/* [RW 1] Input enable for TX PBF user packet port0 IF */
#define NIG_REG_EGRESS_PBF0_IN_EN 0x100cc
/* [RW 1] Input enable for TX PBF user packet port1 IF */
#define NIG_REG_INGRESS_EOP_LB_FIFO 0x104e4
/* [RW 1] led 10g for port 0 */
#define NIG_REG_LED_10G_P0 0x10320
+/* [RW 1] led 10g for port 1 */
+#define NIG_REG_LED_10G_P1 0x10324
/* [RW 1] Port0: This bit is set to enable the use of the
~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 field
defined below. If this bit is cleared; then the blink rate will be about
/* [RW 4] led mode for port0: 0 MAC; 1-3 PHY1; 4 MAC2; 5-7 PHY4; 8-MAC3;
9-11PHY7; 12 MAC4; 13-15 PHY10; */
#define NIG_REG_LED_MODE_P0 0x102f0
+#define NIG_REG_LLH0_ACPI_PAT_0_CRC 0x1015c
+#define NIG_REG_LLH0_ACPI_PAT_6_LEN 0x10154
#define NIG_REG_LLH0_BRB1_DRV_MASK 0x10244
+#define NIG_REG_LLH0_BRB1_DRV_MASK_MF 0x16048
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH0_BRB1_NOT_MCP 0x1025c
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH0_CLS_TYPE 0x16080
/* [RW 32] cm header for llh0 */
#define NIG_REG_LLH0_CM_HEADER 0x1007c
+#define NIG_REG_LLH0_DEST_IP_0_1 0x101dc
+#define NIG_REG_LLH0_DEST_MAC_0_0 0x101c0
+/* [RW 16] destination TCP address 1. The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_TCP_0 0x10220
+/* [RW 16] destination UDP address 1 The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_UDP_0 0x10214
#define NIG_REG_LLH0_ERROR_MASK 0x1008c
/* [RW 8] event id for llh0 */
#define NIG_REG_LLH0_EVENT_ID 0x10084
+#define NIG_REG_LLH0_FUNC_EN 0x160fc
+#define NIG_REG_LLH0_FUNC_VLAN_ID 0x16100
+/* [RW 1] Determine the IP version to look for in
+ ~nig_registers_llh0_dest_ip_0.llh0_dest_ip_0. 0 - IPv6; 1-IPv4 */
+#define NIG_REG_LLH0_IPV4_IPV6_0 0x10208
+/* [RW 1] t bit for llh0 */
+#define NIG_REG_LLH0_T_BIT 0x10074
+/* [RW 12] VLAN ID 1. In case of VLAN packet the LLH will look for this ID. */
+#define NIG_REG_LLH0_VLAN_ID_0 0x1022c
/* [RW 8] init credit counter for port0 in LLH */
#define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554
#define NIG_REG_LLH0_XCM_MASK 0x10130
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH1_CLS_TYPE 0x16084
/* [RW 32] cm header for llh1 */
#define NIG_REG_LLH1_CM_HEADER 0x10080
#define NIG_REG_LLH1_ERROR_MASK 0x10090
/* [RW 8] init credit counter for port1 in LLH */
#define NIG_REG_LLH1_XCM_INIT_CREDIT 0x10564
#define NIG_REG_LLH1_XCM_MASK 0x10134
+/* [RW 1] When this bit is set; the LLH will expect all packets to be with
+ e1hov */
+#define NIG_REG_LLH_E1HOV_MODE 0x160d8
+/* [RW 1] When this bit is set; the LLH will classify the packet before
+ sending it to the BRB or calculating WoL on it. */
+#define NIG_REG_LLH_MF_MODE 0x16024
#define NIG_REG_MASK_INTERRUPT_PORT0 0x10330
#define NIG_REG_MASK_INTERRUPT_PORT1 0x10334
/* [RW 1] Output signal from NIG to EMAC0. When set enables the EMAC0 block. */
#define NIG_REG_NIG_EMAC0_EN 0x1003c
+/* [RW 1] Output signal from NIG to EMAC1. When set enables the EMAC1 block. */
+#define NIG_REG_NIG_EMAC1_EN 0x10040
/* [RW 1] Output signal from NIG to TX_EMAC0. When set indicates to the
EMAC0 to strip the CRC from the ingress packets. */
#define NIG_REG_NIG_INGRESS_EMAC0_NO_CRC 0x10044
+/* [R 32] Interrupt register #0 read */
+#define NIG_REG_NIG_INT_STS_0 0x103b0
+#define NIG_REG_NIG_INT_STS_1 0x103c0
+/* [R 32] Parity register #0 read */
+#define NIG_REG_NIG_PRTY_STS 0x103d0
/* [RW 1] Input enable for RX PBF LP IF */
#define NIG_REG_PBF_LB_IN_EN 0x100b4
/* [RW 1] Value of this register will be transmitted to port swap when
#define NIG_REG_XCM0_OUT_EN 0x100f0
/* [RW 1] output enable for RX_XCM1 IF */
#define NIG_REG_XCM1_OUT_EN 0x100f4
+/* [RW 1] control to xgxs - remote PHY in-band MDIO */
+#define NIG_REG_XGXS0_CTRL_EXTREMOTEMDIOST 0x10348
/* [RW 5] control to xgxs - CL45 DEVAD */
#define NIG_REG_XGXS0_CTRL_MD_DEVAD 0x1033c
+/* [RW 1] control to xgxs; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_XGXS0_CTRL_MD_ST 0x10338
/* [RW 5] control to xgxs - CL22 PHY_ADD and CL45 PRTAD */
#define NIG_REG_XGXS0_CTRL_PHY_ADDR 0x10340
/* [R 1] status from xgxs0 that inputs to interrupt logic of link10g. */
#define PRS_REG_CM_HDR_TYPE_4 0x40088
/* [RW 32] The CM header in case there was not a match on the connection */
#define PRS_REG_CM_NO_MATCH_HDR 0x400b8
+/* [RW 1] Indicates if in e1hov mode. 0=non-e1hov mode; 1=e1hov mode. */
+#define PRS_REG_E1HOV_MODE 0x401c8
/* [RW 8] The 8-bit event ID for a match and packet type 1. Used in packet
start message to TCM. */
#define PRS_REG_EVENT_ID_1 0x40054
#define PRS_REG_EVENT_ID_2 0x40058
#define PRS_REG_EVENT_ID_3 0x4005c
+/* [RW 16] The Ethernet type value for FCoE */
+#define PRS_REG_FCOE_TYPE 0x401d0
/* [RW 8] Context region for flush packet with packet type 0. Used in CFC
load request message. */
#define PRS_REG_FLUSH_REGIONS_TYPE_0 0x40004
#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
#define PXP2_REG_PGL_CONTROL0 0x120490
#define PXP2_REG_PGL_CONTROL1 0x120514
+/* [RW 32] third dword data of expansion rom request. this register is
+ special. reading from it provides a vector outstanding read requests. if
+ a bit is zero it means that a read request on the corresponding tag did
+ not finish yet (not all completions have arrived for it) */
+#define PXP2_REG_PGL_EXP_ROM2 0x120808
/* [RW 32] Inbound interrupt table for CSDM: bits[31:16]-mask;
its[15:0]-address */
#define PXP2_REG_PGL_INT_CSDM_0 0x1204f4
/* [R 1] this bit indicates that a read request was blocked because of
bus_master_en was deasserted */
#define PXP2_REG_PGL_READ_BLOCKED 0x120568
-/* [R 6] debug only */
-#define PXP2_REG_PGL_TXR_CDTS 0x120528
+#define PXP2_REG_PGL_TAGS_LIMIT 0x1205a8
/* [R 18] debug only */
#define PXP2_REG_PGL_TXW_CDTS 0x12052c
/* [R 1] this bit indicates that a write request was blocked because of
#define PXP2_REG_PSWRQ_QM0_L2P 0x120038
#define PXP2_REG_PSWRQ_SRC0_L2P 0x120054
#define PXP2_REG_PSWRQ_TM0_L2P 0x12001c
+#define PXP2_REG_PSWRQ_TSDM0_L2P 0x1200e0
/* [RW 25] Interrupt mask register #0 read/write */
#define PXP2_REG_PXP2_INT_MASK 0x120578
/* [R 25] Interrupt register #0 read */
#define PXP2_REG_RQ_BW_WR_UBOUND29 0x1202a4
/* [RW 7] Bandwidth upper bound for VQ30 */
#define PXP2_REG_RQ_BW_WR_UBOUND30 0x1202a8
+/* [RW 18] external first_mem_addr field in L2P table for CDU module port 0 */
+#define PXP2_REG_RQ_CDU0_EFIRST_MEM_ADDR 0x120008
/* [RW 2] Endian mode for cdu */
#define PXP2_REG_RQ_CDU_ENDIAN_M 0x1201a0
+#define PXP2_REG_RQ_CDU_FIRST_ILT 0x12061c
+#define PXP2_REG_RQ_CDU_LAST_ILT 0x120620
/* [RW 3] page size in L2P table for CDU module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_CDU_P_SIZE 0x120018
/* [RW 1] When '1'; requests will enter input buffers but wont get out
towards the glue */
#define PXP2_REG_RQ_DISABLE_INPUTS 0x120330
+/* [RW 1] 1 - SR will be aligned by 64B; 0 - SR will be aligned by 8B */
+#define PXP2_REG_RQ_DRAM_ALIGN 0x1205b0
+/* [RW 1] If 1 ILT failiue will not result in ELT access; An interrupt will
+ be asserted */
+#define PXP2_REG_RQ_ELT_DISABLE 0x12066c
/* [RW 2] Endian mode for hc */
#define PXP2_REG_RQ_HC_ENDIAN_M 0x1201a8
+/* [RW 1] when '0' ILT logic will work as in A0; otherwise B0; for back
+ compatibility needs; Note that different registers are used per mode */
+#define PXP2_REG_RQ_ILT_MODE 0x1205b4
/* [WB 53] Onchip address table */
#define PXP2_REG_RQ_ONCHIP_AT 0x122000
+/* [WB 53] Onchip address table - B0 */
+#define PXP2_REG_RQ_ONCHIP_AT_B0 0x128000
/* [RW 13] Pending read limiter threshold; in Dwords */
#define PXP2_REG_RQ_PDR_LIMIT 0x12033c
/* [RW 2] Endian mode for qm */
#define PXP2_REG_RQ_QM_ENDIAN_M 0x120194
+#define PXP2_REG_RQ_QM_FIRST_ILT 0x120634
+#define PXP2_REG_RQ_QM_LAST_ILT 0x120638
/* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_QM_P_SIZE 0x120050
#define PXP2_REG_RQ_RD_MBS1 0x120168
/* [RW 2] Endian mode for src */
#define PXP2_REG_RQ_SRC_ENDIAN_M 0x12019c
+#define PXP2_REG_RQ_SRC_FIRST_ILT 0x12063c
+#define PXP2_REG_RQ_SRC_LAST_ILT 0x120640
/* [RW 3] page size in L2P table for SRC module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_SRC_P_SIZE 0x12006c
/* [RW 2] Endian mode for tm */
#define PXP2_REG_RQ_TM_ENDIAN_M 0x120198
+#define PXP2_REG_RQ_TM_FIRST_ILT 0x120644
+#define PXP2_REG_RQ_TM_LAST_ILT 0x120648
/* [RW 3] page size in L2P table for TM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_TM_P_SIZE 0x120034
/* [R 5] Number of entries in the ufifo; his fifo has l2p completions */
#define PXP2_REG_RQ_UFIFO_NUM_OF_ENTRY 0x12080c
+/* [RW 18] external first_mem_addr field in L2P table for USDM module port 0 */
+#define PXP2_REG_RQ_USDM0_EFIRST_MEM_ADDR 0x120094
/* [R 8] Number of entries occupied by vq 0 in pswrq memory */
#define PXP2_REG_RQ_VQ0_ENTRY_CNT 0x120810
/* [R 8] Number of entries occupied by vq 10 in pswrq memory */
/* [RW 3] Max burst size filed for write requests port 1; 000 - 128B;
001:256B; 010: 512B; */
#define PXP2_REG_RQ_WR_MBS1 0x120164
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CDU_MPS 0x1205f0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CSDM_MPS 0x1205d0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DBG_MPS 0x1205e8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DMAE_MPS 0x1205ec
/* [RW 10] if Number of entries in dmae fifo will be higer than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_DMAE_TH 0x120368
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_HC_MPS 0x1205c8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_QM_MPS 0x1205dc
+/* [RW 1] 0 - working in A0 mode; - working in B0 mode */
+#define PXP2_REG_WR_REV_MODE 0x120670
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_SRC_MPS 0x1205e4
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TM_MPS 0x1205e0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TSDM_MPS 0x1205d4
/* [RW 10] if Number of entries in usdmdp fifo will be higer than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_USDMDP_TH 0x120348
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_USDM_MPS 0x1205cc
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_XSDM_MPS 0x1205d8
/* [R 1] debug only: Indication if PSWHST arbiter is idle */
#define PXP_REG_HST_ARB_IS_IDLE 0x103004
/* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means
this client is waiting for the arbiter. */
#define PXP_REG_HST_CLIENTS_WAITING_TO_ARB 0x103008
+/* [R 1] debug only: '1' means this PSWHST is discarding doorbells. This bit
+ should update accoring to 'hst_discard_doorbells' register when the state
+ machine is idle */
+#define PXP_REG_HST_DISCARD_DOORBELLS_STATUS 0x1030a0
+/* [R 6] debug only: A bit mask for all PSWHST internal write clients. '1'
+ means this PSWHST is discarding inputs from this client. Each bit should
+ update accoring to 'hst_discard_internal_writes' register when the state
+ machine is idle. */
+#define PXP_REG_HST_DISCARD_INTERNAL_WRITES_STATUS 0x10309c
/* [WB 160] Used for initialization of the inbound interrupts memory */
#define PXP_REG_HST_INBOUND_INT 0x103800
/* [RW 32] Interrupt mask register #0 read/write */
#define QM_REG_ACTCTRINITVAL_3 0x16804c
/* [RW 32] The base logical address (in bytes) of each physical queue. The
index I represents the physical queue number. The 12 lsbs are ignore and
- considered zero so practically there are only 20 bits in this register. */
+ considered zero so practically there are only 20 bits in this register;
+ queues 63-0 */
#define QM_REG_BASEADDR 0x168900
/* [RW 16] The byte credit cost for each task. This value is for both ports */
#define QM_REG_BYTECRDCOST 0x168234
/* [RW 16] The initial byte credit value for both ports. */
#define QM_REG_BYTECRDINITVAL 0x168238
/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
- queue uses port 0 else it uses port 1. */
+ queue uses port 0 else it uses port 1; queues 31-0 */
#define QM_REG_BYTECRDPORT_LSB 0x168228
/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
- queue uses port 0 else it uses port 1. */
+ queue uses port 0 else it uses port 1; queues 95-64 */
+#define QM_REG_BYTECRDPORT_LSB_EXT_A 0x16e520
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 63-32 */
#define QM_REG_BYTECRDPORT_MSB 0x168224
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 127-96 */
+#define QM_REG_BYTECRDPORT_MSB_EXT_A 0x16e51c
/* [RW 16] The byte credit value that if above the QM is considered almost
full */
#define QM_REG_BYTECREDITAFULLTHR 0x168094
#define QM_REG_CMINTVOQMASK_6 0x16820c
#define QM_REG_CMINTVOQMASK_7 0x168210
/* [RW 20] The number of connections divided by 16 which dictates the size
- of each queue per port 0 */
+ of each queue which belongs to even function number. */
#define QM_REG_CONNNUM_0 0x168020
/* [R 6] Keep the fill level of the fifo from write client 4 */
#define QM_REG_CQM_WRC_FIFOLVL 0x168018
bypass enable */
#define QM_REG_ENBYPVOQMASK 0x16823c
/* [RW 32] A bit mask per each physical queue. If a bit is set then the
- physical queue uses the byte credit */
+ physical queue uses the byte credit; queues 31-0 */
#define QM_REG_ENBYTECRD_LSB 0x168220
/* [RW 32] A bit mask per each physical queue. If a bit is set then the
- physical queue uses the byte credit */
+ physical queue uses the byte credit; queues 95-64 */
+#define QM_REG_ENBYTECRD_LSB_EXT_A 0x16e518
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 63-32 */
#define QM_REG_ENBYTECRD_MSB 0x16821c
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 127-96 */
+#define QM_REG_ENBYTECRD_MSB_EXT_A 0x16e514
/* [RW 4] If cleared then the secondary interface will not be served by the
RR arbiter */
#define QM_REG_ENSEC 0x1680f0
-/* [RW 32] A bit vector per each physical queue which selects which function
- number to use on PCI access for that queue. */
+/* [RW 32] NA */
#define QM_REG_FUNCNUMSEL_LSB 0x168230
-/* [RW 32] A bit vector per each physical queue which selects which function
- number to use on PCI access for that queue. */
+/* [RW 32] NA */
#define QM_REG_FUNCNUMSEL_MSB 0x16822c
/* [RW 32] A mask register to mask the Almost empty signals which will not
- be use for the almost empty indication to the HW block */
+ be use for the almost empty indication to the HW block; queues 31:0 */
#define QM_REG_HWAEMPTYMASK_LSB 0x168218
/* [RW 32] A mask register to mask the Almost empty signals which will not
- be use for the almost empty indication to the HW block */
+ be use for the almost empty indication to the HW block; queues 95-64 */
+#define QM_REG_HWAEMPTYMASK_LSB_EXT_A 0x16e510
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 63:32 */
#define QM_REG_HWAEMPTYMASK_MSB 0x168214
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 127-96 */
+#define QM_REG_HWAEMPTYMASK_MSB_EXT_A 0x16e50c
/* [RW 4] The number of outstanding request to CFC */
#define QM_REG_OUTLDREQ 0x168804
/* [RC 1] A flag to indicate that overflow error occurred in one of the
queues. */
#define QM_REG_OVFERROR 0x16805c
-/* [RC 6] the Q were the qverflow occurs */
+/* [RC 7] the Q were the qverflow occurs */
#define QM_REG_OVFQNUM 0x168058
-/* [R 32] Pause state for physical queues 31-0 */
+/* [R 16] Pause state for physical queues 15-0 */
#define QM_REG_PAUSESTATE0 0x168410
-/* [R 32] Pause state for physical queues 64-32 */
+/* [R 16] Pause state for physical queues 31-16 */
#define QM_REG_PAUSESTATE1 0x168414
+/* [R 16] Pause state for physical queues 47-32 */
+#define QM_REG_PAUSESTATE2 0x16e684
+/* [R 16] Pause state for physical queues 63-48 */
+#define QM_REG_PAUSESTATE3 0x16e688
+/* [R 16] Pause state for physical queues 79-64 */
+#define QM_REG_PAUSESTATE4 0x16e68c
+/* [R 16] Pause state for physical queues 95-80 */
+#define QM_REG_PAUSESTATE5 0x16e690
+/* [R 16] Pause state for physical queues 111-96 */
+#define QM_REG_PAUSESTATE6 0x16e694
+/* [R 16] Pause state for physical queues 127-112 */
+#define QM_REG_PAUSESTATE7 0x16e698
/* [RW 2] The PCI attributes field used in the PCI request. */
#define QM_REG_PCIREQAT 0x168054
/* [R 16] The byte credit of port 0 */
#define QM_REG_PORT0BYTECRD 0x168300
/* [R 16] The byte credit of port 1 */
#define QM_REG_PORT1BYTECRD 0x168304
-/* [WB 54] Pointer Table Memory; The mapping is as follow: ptrtbl[53:30]
- read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read bank0;
- ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+/* [RW 3] pci function number of queues 15-0 */
+#define QM_REG_PQ2PCIFUNC_0 0x16e6bc
+#define QM_REG_PQ2PCIFUNC_1 0x16e6c0
+#define QM_REG_PQ2PCIFUNC_2 0x16e6c4
+#define QM_REG_PQ2PCIFUNC_3 0x16e6c8
+#define QM_REG_PQ2PCIFUNC_4 0x16e6cc
+#define QM_REG_PQ2PCIFUNC_5 0x16e6d0
+#define QM_REG_PQ2PCIFUNC_6 0x16e6d4
+#define QM_REG_PQ2PCIFUNC_7 0x16e6d8
+/* [WB 54] Pointer Table Memory for queues 63-0; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
#define QM_REG_PTRTBL 0x168a00
+/* [WB 54] Pointer Table Memory for queues 127-64; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+#define QM_REG_PTRTBL_EXT_A 0x16e200
/* [RW 2] Interrupt mask register #0 read/write */
#define QM_REG_QM_INT_MASK 0x168444
/* [R 2] Interrupt register #0 read */
#define QM_REG_QM_INT_STS 0x168438
-/* [RW 9] Parity mask register #0 read/write */
+/* [RW 12] Parity mask register #0 read/write */
#define QM_REG_QM_PRTY_MASK 0x168454
-/* [R 9] Parity register #0 read */
+/* [R 12] Parity register #0 read */
#define QM_REG_QM_PRTY_STS 0x168448
/* [R 32] Current queues in pipeline: Queues from 32 to 63 */
#define QM_REG_QSTATUS_HIGH 0x16802c
+/* [R 32] Current queues in pipeline: Queues from 96 to 127 */
+#define QM_REG_QSTATUS_HIGH_EXT_A 0x16e408
/* [R 32] Current queues in pipeline: Queues from 0 to 31 */
#define QM_REG_QSTATUS_LOW 0x168028
-/* [R 24] The number of tasks queued for each queue */
+/* [R 32] Current queues in pipeline: Queues from 64 to 95 */
+#define QM_REG_QSTATUS_LOW_EXT_A 0x16e404
+/* [R 24] The number of tasks queued for each queue; queues 63-0 */
#define QM_REG_QTASKCTR_0 0x168308
+/* [R 24] The number of tasks queued for each queue; queues 127-64 */
+#define QM_REG_QTASKCTR_EXT_A_0 0x16e584
/* [RW 4] Queue tied to VOQ */
#define QM_REG_QVOQIDX_0 0x1680f4
#define QM_REG_QVOQIDX_10 0x16811c
+#define QM_REG_QVOQIDX_100 0x16e49c
+#define QM_REG_QVOQIDX_101 0x16e4a0
+#define QM_REG_QVOQIDX_102 0x16e4a4
+#define QM_REG_QVOQIDX_103 0x16e4a8
+#define QM_REG_QVOQIDX_104 0x16e4ac
+#define QM_REG_QVOQIDX_105 0x16e4b0
+#define QM_REG_QVOQIDX_106 0x16e4b4
+#define QM_REG_QVOQIDX_107 0x16e4b8
+#define QM_REG_QVOQIDX_108 0x16e4bc
+#define QM_REG_QVOQIDX_109 0x16e4c0
+#define QM_REG_QVOQIDX_100 0x16e49c
+#define QM_REG_QVOQIDX_101 0x16e4a0
+#define QM_REG_QVOQIDX_102 0x16e4a4
+#define QM_REG_QVOQIDX_103 0x16e4a8
+#define QM_REG_QVOQIDX_104 0x16e4ac
+#define QM_REG_QVOQIDX_105 0x16e4b0
+#define QM_REG_QVOQIDX_106 0x16e4b4
+#define QM_REG_QVOQIDX_107 0x16e4b8
+#define QM_REG_QVOQIDX_108 0x16e4bc
+#define QM_REG_QVOQIDX_109 0x16e4c0
#define QM_REG_QVOQIDX_11 0x168120
+#define QM_REG_QVOQIDX_110 0x16e4c4
+#define QM_REG_QVOQIDX_111 0x16e4c8
+#define QM_REG_QVOQIDX_112 0x16e4cc
+#define QM_REG_QVOQIDX_113 0x16e4d0
+#define QM_REG_QVOQIDX_114 0x16e4d4
+#define QM_REG_QVOQIDX_115 0x16e4d8
+#define QM_REG_QVOQIDX_116 0x16e4dc
+#define QM_REG_QVOQIDX_117 0x16e4e0
+#define QM_REG_QVOQIDX_118 0x16e4e4
+#define QM_REG_QVOQIDX_119 0x16e4e8
+#define QM_REG_QVOQIDX_110 0x16e4c4
+#define QM_REG_QVOQIDX_111 0x16e4c8
+#define QM_REG_QVOQIDX_112 0x16e4cc
+#define QM_REG_QVOQIDX_113 0x16e4d0
+#define QM_REG_QVOQIDX_114 0x16e4d4
+#define QM_REG_QVOQIDX_115 0x16e4d8
+#define QM_REG_QVOQIDX_116 0x16e4dc
+#define QM_REG_QVOQIDX_117 0x16e4e0
+#define QM_REG_QVOQIDX_118 0x16e4e4
+#define QM_REG_QVOQIDX_119 0x16e4e8
#define QM_REG_QVOQIDX_12 0x168124
+#define QM_REG_QVOQIDX_120 0x16e4ec
+#define QM_REG_QVOQIDX_121 0x16e4f0
+#define QM_REG_QVOQIDX_122 0x16e4f4
+#define QM_REG_QVOQIDX_123 0x16e4f8
+#define QM_REG_QVOQIDX_124 0x16e4fc
+#define QM_REG_QVOQIDX_125 0x16e500
+#define QM_REG_QVOQIDX_126 0x16e504
+#define QM_REG_QVOQIDX_127 0x16e508
+#define QM_REG_QVOQIDX_120 0x16e4ec
+#define QM_REG_QVOQIDX_121 0x16e4f0
+#define QM_REG_QVOQIDX_122 0x16e4f4
+#define QM_REG_QVOQIDX_123 0x16e4f8
+#define QM_REG_QVOQIDX_124 0x16e4fc
+#define QM_REG_QVOQIDX_125 0x16e500
+#define QM_REG_QVOQIDX_126 0x16e504
+#define QM_REG_QVOQIDX_127 0x16e508
#define QM_REG_QVOQIDX_13 0x168128
#define QM_REG_QVOQIDX_14 0x16812c
#define QM_REG_QVOQIDX_15 0x168130
#define QM_REG_QVOQIDX_16 0x168134
#define QM_REG_QVOQIDX_17 0x168138
#define QM_REG_QVOQIDX_21 0x168148
+#define QM_REG_QVOQIDX_22 0x16814c
+#define QM_REG_QVOQIDX_23 0x168150
+#define QM_REG_QVOQIDX_24 0x168154
#define QM_REG_QVOQIDX_25 0x168158
+#define QM_REG_QVOQIDX_26 0x16815c
+#define QM_REG_QVOQIDX_27 0x168160
+#define QM_REG_QVOQIDX_28 0x168164
#define QM_REG_QVOQIDX_29 0x168168
+#define QM_REG_QVOQIDX_30 0x16816c
+#define QM_REG_QVOQIDX_31 0x168170
#define QM_REG_QVOQIDX_32 0x168174
#define QM_REG_QVOQIDX_33 0x168178
#define QM_REG_QVOQIDX_34 0x16817c
#define QM_REG_QVOQIDX_61 0x1681e8
#define QM_REG_QVOQIDX_62 0x1681ec
#define QM_REG_QVOQIDX_63 0x1681f0
+#define QM_REG_QVOQIDX_64 0x16e40c
+#define QM_REG_QVOQIDX_65 0x16e410
+#define QM_REG_QVOQIDX_66 0x16e414
+#define QM_REG_QVOQIDX_67 0x16e418
+#define QM_REG_QVOQIDX_68 0x16e41c
+#define QM_REG_QVOQIDX_69 0x16e420
#define QM_REG_QVOQIDX_60 0x1681e4
#define QM_REG_QVOQIDX_61 0x1681e8
#define QM_REG_QVOQIDX_62 0x1681ec
#define QM_REG_QVOQIDX_63 0x1681f0
+#define QM_REG_QVOQIDX_64 0x16e40c
+#define QM_REG_QVOQIDX_65 0x16e410
+#define QM_REG_QVOQIDX_69 0x16e420
#define QM_REG_QVOQIDX_7 0x168110
+#define QM_REG_QVOQIDX_70 0x16e424
+#define QM_REG_QVOQIDX_71 0x16e428
+#define QM_REG_QVOQIDX_72 0x16e42c
+#define QM_REG_QVOQIDX_73 0x16e430
+#define QM_REG_QVOQIDX_74 0x16e434
+#define QM_REG_QVOQIDX_75 0x16e438
+#define QM_REG_QVOQIDX_76 0x16e43c
+#define QM_REG_QVOQIDX_77 0x16e440
+#define QM_REG_QVOQIDX_78 0x16e444
+#define QM_REG_QVOQIDX_79 0x16e448
+#define QM_REG_QVOQIDX_70 0x16e424
+#define QM_REG_QVOQIDX_71 0x16e428
+#define QM_REG_QVOQIDX_72 0x16e42c
+#define QM_REG_QVOQIDX_73 0x16e430
+#define QM_REG_QVOQIDX_74 0x16e434
+#define QM_REG_QVOQIDX_75 0x16e438
+#define QM_REG_QVOQIDX_76 0x16e43c
+#define QM_REG_QVOQIDX_77 0x16e440
+#define QM_REG_QVOQIDX_78 0x16e444
+#define QM_REG_QVOQIDX_79 0x16e448
#define QM_REG_QVOQIDX_8 0x168114
+#define QM_REG_QVOQIDX_80 0x16e44c
+#define QM_REG_QVOQIDX_81 0x16e450
+#define QM_REG_QVOQIDX_82 0x16e454
+#define QM_REG_QVOQIDX_83 0x16e458
+#define QM_REG_QVOQIDX_84 0x16e45c
+#define QM_REG_QVOQIDX_85 0x16e460
+#define QM_REG_QVOQIDX_86 0x16e464
+#define QM_REG_QVOQIDX_87 0x16e468
+#define QM_REG_QVOQIDX_88 0x16e46c
+#define QM_REG_QVOQIDX_89 0x16e470
+#define QM_REG_QVOQIDX_80 0x16e44c
+#define QM_REG_QVOQIDX_81 0x16e450
+#define QM_REG_QVOQIDX_85 0x16e460
+#define QM_REG_QVOQIDX_86 0x16e464
+#define QM_REG_QVOQIDX_87 0x16e468
+#define QM_REG_QVOQIDX_88 0x16e46c
+#define QM_REG_QVOQIDX_89 0x16e470
#define QM_REG_QVOQIDX_9 0x168118
-/* [R 24] Remaining pause timeout for port 0 */
+#define QM_REG_QVOQIDX_90 0x16e474
+#define QM_REG_QVOQIDX_91 0x16e478
+#define QM_REG_QVOQIDX_92 0x16e47c
+#define QM_REG_QVOQIDX_93 0x16e480
+#define QM_REG_QVOQIDX_94 0x16e484
+#define QM_REG_QVOQIDX_95 0x16e488
+#define QM_REG_QVOQIDX_96 0x16e48c
+#define QM_REG_QVOQIDX_97 0x16e490
+#define QM_REG_QVOQIDX_98 0x16e494
+#define QM_REG_QVOQIDX_99 0x16e498
+#define QM_REG_QVOQIDX_90 0x16e474
+#define QM_REG_QVOQIDX_91 0x16e478
+#define QM_REG_QVOQIDX_92 0x16e47c
+#define QM_REG_QVOQIDX_93 0x16e480
+#define QM_REG_QVOQIDX_94 0x16e484
+#define QM_REG_QVOQIDX_95 0x16e488
+#define QM_REG_QVOQIDX_96 0x16e48c
+#define QM_REG_QVOQIDX_97 0x16e490
+#define QM_REG_QVOQIDX_98 0x16e494
+#define QM_REG_QVOQIDX_99 0x16e498
+/* [R 24] Remaining pause timeout for queues 15-0 */
#define QM_REG_REMAINPAUSETM0 0x168418
-/* [R 24] Remaining pause timeout for port 1 */
+/* [R 24] Remaining pause timeout for queues 31-16 */
#define QM_REG_REMAINPAUSETM1 0x16841c
+/* [R 24] Remaining pause timeout for queues 47-32 */
+#define QM_REG_REMAINPAUSETM2 0x16e69c
+/* [R 24] Remaining pause timeout for queues 63-48 */
+#define QM_REG_REMAINPAUSETM3 0x16e6a0
+/* [R 24] Remaining pause timeout for queues 79-64 */
+#define QM_REG_REMAINPAUSETM4 0x16e6a4
+/* [R 24] Remaining pause timeout for queues 95-80 */
+#define QM_REG_REMAINPAUSETM5 0x16e6a8
+/* [R 24] Remaining pause timeout for queues 111-96 */
+#define QM_REG_REMAINPAUSETM6 0x16e6ac
+/* [R 24] Remaining pause timeout for queues 127-112 */
+#define QM_REG_REMAINPAUSETM7 0x16e6b0
/* [RW 1] Initialization bit command */
#define QM_REG_SOFT_RESET 0x168428
/* [RW 8] The credit cost per every task in the QM. A value per each VOQ */
#define QM_REG_VOQINITCREDIT_4 0x168070
#define QM_REG_VOQINITCREDIT_5 0x168074
/* [RW 1] The port of which VOQ belongs */
+#define QM_REG_VOQPORT_0 0x1682a0
#define QM_REG_VOQPORT_1 0x1682a4
#define QM_REG_VOQPORT_10 0x1682c8
#define QM_REG_VOQPORT_11 0x1682cc
#define QM_REG_VOQPORT_2 0x1682a8
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_0_LSB 0x168240
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_0_LSB_EXT_A 0x16e524
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_0_MSB 0x168244
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_0_MSB_EXT_A 0x16e528
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_10_LSB 0x168290
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_10_LSB_EXT_A 0x16e574
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_10_MSB 0x168294
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_10_MSB_EXT_A 0x16e578
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_11_LSB 0x168298
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_11_LSB_EXT_A 0x16e57c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_11_MSB 0x16829c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_11_MSB_EXT_A 0x16e580
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_1_LSB 0x168248
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_1_LSB_EXT_A 0x16e52c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_1_MSB 0x16824c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_1_MSB_EXT_A 0x16e530
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_2_LSB 0x168250
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_2_LSB_EXT_A 0x16e534
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_2_MSB 0x168254
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_2_MSB_EXT_A 0x16e538
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_3_LSB 0x168258
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_3_LSB_EXT_A 0x16e53c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_3_MSB_EXT_A 0x16e540
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_4_LSB 0x168260
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_4_LSB_EXT_A 0x16e544
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_4_MSB 0x168264
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_4_MSB_EXT_A 0x16e548
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_5_LSB 0x168268
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_5_LSB_EXT_A 0x16e54c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_5_MSB 0x16826c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_5_MSB_EXT_A 0x16e550
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_6_LSB 0x168270
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_6_LSB_EXT_A 0x16e554
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_6_MSB 0x168274
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_6_MSB_EXT_A 0x16e558
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_7_LSB 0x168278
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_7_LSB_EXT_A 0x16e55c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_7_MSB 0x16827c
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_7_MSB_EXT_A 0x16e560
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_8_LSB 0x168280
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_8_LSB_EXT_A 0x16e564
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
#define QM_REG_VOQQMASK_8_MSB 0x168284
-/* [RW 32] The physical queue number associated with each VOQ */
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_8_MSB_EXT_A 0x16e568
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
#define QM_REG_VOQQMASK_9_LSB 0x168288
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_9_LSB_EXT_A 0x16e56c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_9_MSB_EXT_A 0x16e570
/* [RW 32] Wrr weights */
#define QM_REG_WRRWEIGHTS_0 0x16880c
#define QM_REG_WRRWEIGHTS_1 0x168810
#define QM_REG_WRRWEIGHTS_15 0x168828
#define QM_REG_WRRWEIGHTS_15_SIZE 1
/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_16 0x16e000
+#define QM_REG_WRRWEIGHTS_16_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_17 0x16e004
+#define QM_REG_WRRWEIGHTS_17_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_18 0x16e008
+#define QM_REG_WRRWEIGHTS_18_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_19 0x16e00c
+#define QM_REG_WRRWEIGHTS_19_SIZE 1
+/* [RW 32] Wrr weights */
#define QM_REG_WRRWEIGHTS_10 0x168814
#define QM_REG_WRRWEIGHTS_11 0x168818
#define QM_REG_WRRWEIGHTS_12 0x16881c
#define QM_REG_WRRWEIGHTS_13 0x168820
#define QM_REG_WRRWEIGHTS_14 0x168824
#define QM_REG_WRRWEIGHTS_15 0x168828
+#define QM_REG_WRRWEIGHTS_16 0x16e000
+#define QM_REG_WRRWEIGHTS_17 0x16e004
+#define QM_REG_WRRWEIGHTS_18 0x16e008
+#define QM_REG_WRRWEIGHTS_19 0x16e00c
#define QM_REG_WRRWEIGHTS_2 0x16882c
+#define QM_REG_WRRWEIGHTS_20 0x16e010
+#define QM_REG_WRRWEIGHTS_20_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_21 0x16e014
+#define QM_REG_WRRWEIGHTS_21_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_22 0x16e018
+#define QM_REG_WRRWEIGHTS_22_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_23 0x16e01c
+#define QM_REG_WRRWEIGHTS_23_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_24 0x16e020
+#define QM_REG_WRRWEIGHTS_24_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_25 0x16e024
+#define QM_REG_WRRWEIGHTS_25_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_26 0x16e028
+#define QM_REG_WRRWEIGHTS_26_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_27 0x16e02c
+#define QM_REG_WRRWEIGHTS_27_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_28 0x16e030
+#define QM_REG_WRRWEIGHTS_28_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_29 0x16e034
+#define QM_REG_WRRWEIGHTS_29_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_20 0x16e010
+#define QM_REG_WRRWEIGHTS_21 0x16e014
+#define QM_REG_WRRWEIGHTS_22 0x16e018
+#define QM_REG_WRRWEIGHTS_23 0x16e01c
+#define QM_REG_WRRWEIGHTS_24 0x16e020
+#define QM_REG_WRRWEIGHTS_25 0x16e024
+#define QM_REG_WRRWEIGHTS_26 0x16e028
+#define QM_REG_WRRWEIGHTS_27 0x16e02c
+#define QM_REG_WRRWEIGHTS_28 0x16e030
+#define QM_REG_WRRWEIGHTS_29 0x16e034
#define QM_REG_WRRWEIGHTS_3 0x168830
+#define QM_REG_WRRWEIGHTS_30 0x16e038
+#define QM_REG_WRRWEIGHTS_30_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_31 0x16e03c
+#define QM_REG_WRRWEIGHTS_31_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_30 0x16e038
+#define QM_REG_WRRWEIGHTS_31 0x16e03c
#define QM_REG_WRRWEIGHTS_4 0x168834
#define QM_REG_WRRWEIGHTS_5 0x168838
#define QM_REG_WRRWEIGHTS_6 0x16883c
#define QM_REG_WRRWEIGHTS_9 0x168848
/* [R 6] Keep the fill level of the fifo from write client 1 */
#define QM_REG_XQM_WRC_FIFOLVL 0x168000
+#define BRB1_BRB1_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define BRB1_BRB1_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define BRB1_BRB1_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define BRB1_BRB1_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define BRB1_BRB1_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define BRB1_BRB1_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define BRB1_BRB1_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define BRB1_BRB1_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define CCM_CCM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define CCM_CCM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define CCM_CCM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define CCM_CCM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define CCM_CCM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define CCM_CCM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define CCM_CCM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define CCM_CCM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define CDU_CDU_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define CDU_CDU_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define CDU_CDU_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define CDU_CDU_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define CDU_CDU_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define CDU_CDU_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define CDU_CDU_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define CDU_CDU_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define CFC_CFC_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define CFC_CFC_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define CFC_CFC_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define CFC_CFC_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define CFC_CFC_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define CFC_CFC_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define CFC_CFC_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define CFC_CFC_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define CSDM_CSDM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSDM_CSDM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSDM_CSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSDM_CSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSDM_CSDM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSDM_CSDM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSDM_CSDM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSDM_CSDM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSEM_CSEM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSEM_CSEM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSEM_CSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSEM_CSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSEM_CSEM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSEM_CSEM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define CSEM_CSEM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define CSEM_CSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define DBG_DBG_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define DBG_DBG_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define DBG_DBG_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define DBG_DBG_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define DBG_DBG_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define DBG_DBG_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define DBG_DBG_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define DBG_DBG_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define DMAE_DMAE_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define DMAE_DMAE_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define DMAE_DMAE_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define DMAE_DMAE_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define DMAE_DMAE_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define DMAE_DMAE_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define DMAE_DMAE_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define DMAE_DMAE_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
#define DORQ_DORQ_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
#define DORQ_DORQ_INT_STS_REG_ADDRESS_ERROR_SIZE 0
#define DORQ_DORQ_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
#define DORQ_DORQ_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
#define DORQ_DORQ_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
#define DORQ_DORQ_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define HC_HC_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define HC_HC_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define HC_HC_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define HC_HC_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define HC_HC_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define HC_HC_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define HC_HC_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define HC_HC_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define MISC_MISC_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define MISC_MISC_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define MISC_MISC_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define MISC_MISC_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define MISC_MISC_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define MISC_MISC_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define MISC_MISC_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define MISC_MISC_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
#define NIG_NIG_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
#define NIG_NIG_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
#define NIG_NIG_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
#define NIG_NIG_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
#define NIG_NIG_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
#define NIG_NIG_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define PBF_PBF_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define PBF_PBF_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define PBF_PBF_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define PBF_PBF_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define PBF_PBF_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define PBF_PBF_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define PBF_PBF_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define PBF_PBF_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define PB_PB_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define PB_PB_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define PB_PB_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define PB_PB_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define PB_PB_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define PB_PB_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define PB_PB_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define PB_PB_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define PRS_PRS_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define PRS_PRS_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define PRS_PRS_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define PRS_PRS_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define PRS_PRS_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define PRS_PRS_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define PRS_PRS_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define PRS_PRS_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define PXP2_PXP2_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP2_PXP2_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP2_PXP2_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP2_PXP2_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP2_PXP2_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP2_PXP2_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP2_PXP2_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP2_PXP2_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP_PXP_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP_PXP_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP_PXP_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP_PXP_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP_PXP_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP_PXP_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define PXP_PXP_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define PXP_PXP_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define QM_QM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define QM_QM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define QM_QM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define QM_QM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define QM_QM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define QM_QM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define QM_QM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define QM_QM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define SEM_FAST_SEM_FAST_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define SEM_FAST_SEM_FAST_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define SEM_FAST_SEM_FAST_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define SEM_FAST_SEM_FAST_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define SEM_FAST_SEM_FAST_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define SEM_FAST_SEM_FAST_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define SEM_FAST_SEM_FAST_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define SEM_FAST_SEM_FAST_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define SRC_SRC_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define SRC_SRC_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define SRC_SRC_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define SRC_SRC_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define SRC_SRC_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define SRC_SRC_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define SRC_SRC_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define SRC_SRC_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
#define TCM_TCM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
#define TCM_TCM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
#define TCM_TCM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
#define TCM_TCM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
#define TCM_TCM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
#define TCM_TCM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define TM_TM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define TM_TM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define TM_TM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define TM_TM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define TM_TM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define TM_TM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define TM_TM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define TM_TM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define TSDM_TSDM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSDM_TSDM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSDM_TSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSDM_TSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSDM_TSDM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSDM_TSDM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSDM_TSDM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSDM_TSDM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSEM_TSEM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSEM_TSEM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSEM_TSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSEM_TSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSEM_TSEM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSEM_TSEM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define TSEM_TSEM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define TSEM_TSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define UCM_UCM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define UCM_UCM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define UCM_UCM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define UCM_UCM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define UCM_UCM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define UCM_UCM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define UCM_UCM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define UCM_UCM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define USDM_USDM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USDM_USDM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define USDM_USDM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USDM_USDM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define USDM_USDM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USDM_USDM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define USDM_USDM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USDM_USDM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define USEM_USEM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USEM_USEM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define USEM_USEM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USEM_USEM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define USEM_USEM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USEM_USEM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define USEM_USEM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define USEM_USEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define XCM_XCM_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define XCM_XCM_INT_STS_REG_ADDRESS_ERROR_SIZE 0
+#define XCM_XCM_INT_STS_CLR_REG_ADDRESS_ERROR (0x1<<0)
+#define XCM_XCM_INT_STS_CLR_REG_ADDRESS_ERROR_SIZE 0
+#define XCM_XCM_INT_STS_WR_REG_ADDRESS_ERROR (0x1<<0)
+#define XCM_XCM_INT_STS_WR_REG_ADDRESS_ERROR_SIZE 0
+#define XCM_XCM_INT_MASK_REG_ADDRESS_ERROR (0x1<<0)
+#define XCM_XCM_INT_MASK_REG_ADDRESS_ERROR_SIZE 0
+#define XSDM_XSDM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSDM_XSDM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSDM_XSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSDM_XSDM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSDM_XSDM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSDM_XSDM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSDM_XSDM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSDM_XSDM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSEM_XSEM_INT_STS_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSEM_XSEM_INT_STS_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSEM_XSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSEM_XSEM_INT_STS_CLR_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSEM_XSEM_INT_STS_WR_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSEM_XSEM_INT_STS_WR_0_REG_ADDRESS_ERROR_SIZE 0
+#define XSEM_XSEM_INT_MASK_0_REG_ADDRESS_ERROR (0x1<<0)
+#define XSEM_XSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
#define CFC_DEBUG1_REG_WRITE_AC (0x1<<4)
#define CFC_DEBUG1_REG_WRITE_AC_SIZE 4
/* [R 1] debug only: This bit indicates wheter indicates that external
~dbg_registers_debug_target=0 (internal buffer) */
#define DBG_REG_WRAP_ON_INT_BUFFER 0xc128
#define DBG_REG_WRAP_ON_INT_BUFFER_SIZE 1
+#define QM_QM_PRTY_STS_REG_WRBUFF (0x1<<8)
+#define QM_QM_PRTY_STS_REG_WRBUFF_SIZE 8
+#define QM_QM_PRTY_STS_CLR_REG_WRBUFF (0x1<<8)
+#define QM_QM_PRTY_STS_CLR_REG_WRBUFF_SIZE 8
+#define QM_QM_PRTY_STS_WR_REG_WRBUFF (0x1<<8)
+#define QM_QM_PRTY_STS_WR_REG_WRBUFF_SIZE 8
+#define QM_QM_PRTY_MASK_REG_WRBUFF (0x1<<8)
+#define QM_QM_PRTY_MASK_REG_WRBUFF_SIZE 8
/* [RW 32] Wrr weights */
#define QM_REG_WRRWEIGHTS_0 0x16880c
#define QM_REG_WRRWEIGHTS_0_SIZE 1
/* [RW 32] Wrr weights */
#define QM_REG_WRRWEIGHTS_9 0x168848
#define QM_REG_WRRWEIGHTS_9_SIZE 1
-/* [RW 22] Number of free element in the free list of T2 entries - port 0. */
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_16 0x16e000
+#define QM_REG_WRRWEIGHTS_16_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_17 0x16e004
+#define QM_REG_WRRWEIGHTS_17_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_18 0x16e008
+#define QM_REG_WRRWEIGHTS_18_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_19 0x16e00c
+#define QM_REG_WRRWEIGHTS_19_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_20 0x16e010
+#define QM_REG_WRRWEIGHTS_20_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_21 0x16e014
+#define QM_REG_WRRWEIGHTS_21_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_22 0x16e018
+#define QM_REG_WRRWEIGHTS_22_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_23 0x16e01c
+#define QM_REG_WRRWEIGHTS_23_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_24 0x16e020
+#define QM_REG_WRRWEIGHTS_24_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_25 0x16e024
+#define QM_REG_WRRWEIGHTS_25_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_26 0x16e028
+#define QM_REG_WRRWEIGHTS_26_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_27 0x16e02c
+#define QM_REG_WRRWEIGHTS_27_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_28 0x16e030
+#define QM_REG_WRRWEIGHTS_28_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_29 0x16e034
+#define QM_REG_WRRWEIGHTS_29_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_30 0x16e038
+#define QM_REG_WRRWEIGHTS_30_SIZE 1
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_31 0x16e03c
+#define QM_REG_WRRWEIGHTS_31_SIZE 1
#define SRC_REG_COUNTFREE0 0x40500
-/* [WB 64] First free element in the free list of T2 entries - port 0. */
+/* [RW 1] If clr the searcher is compatible to E1 A0 - support only two
+ ports. If set the searcher support 8 functions. */
+#define SRC_REG_E1HMF_ENABLE 0x404cc
#define SRC_REG_FIRSTFREE0 0x40510
#define SRC_REG_KEYRSS0_0 0x40408
+#define SRC_REG_KEYRSS0_7 0x40424
#define SRC_REG_KEYRSS1_9 0x40454
-/* [WB 64] Last free element in the free list of T2 entries - port 0. */
#define SRC_REG_LASTFREE0 0x40530
-/* [RW 5] The number of hash bits used for the search (h); Values can be 8
- to 24. */
#define SRC_REG_NUMBER_HASH_BITS0 0x40400
/* [RW 1] Reset internal state machines. */
#define SRC_REG_SOFT_RST 0x4049c
-/* [R 1] Interrupt register #0 read */
+/* [R 3] Interrupt register #0 read */
#define SRC_REG_SRC_INT_STS 0x404ac
/* [RW 3] Parity mask register #0 read/write */
#define SRC_REG_SRC_PRTY_MASK 0x404c8
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define TCM_REG_PBF_WEIGHT 0x500b4
-/* [RW 6] The physical queue number 0 per port index. */
#define TCM_REG_PHYS_QNUM0_0 0x500e0
#define TCM_REG_PHYS_QNUM0_1 0x500e4
-/* [RW 6] The physical queue number 1 per port index. */
#define TCM_REG_PHYS_QNUM1_0 0x500e8
+#define TCM_REG_PHYS_QNUM1_1 0x500ec
+#define TCM_REG_PHYS_QNUM2_0 0x500f0
+#define TCM_REG_PHYS_QNUM2_1 0x500f4
+#define TCM_REG_PHYS_QNUM3_0 0x500f8
+#define TCM_REG_PHYS_QNUM3_1 0x500fc
/* [RW 1] Input prs Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
#define TCM_REG_TCM_INT_MASK 0x501dc
/* [R 11] Interrupt register #0 read */
#define TCM_REG_TCM_INT_STS 0x501d0
+/* [R 27] Parity register #0 read */
+#define TCM_REG_TCM_PRTY_STS 0x501e0
/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
mechanism. The fields are: [5:0] - length of the message; 15:6] - message
pointer; 20:16] - next pointer. */
#define TCM_REG_XX_DESCR_TABLE 0x50280
+#define TCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Use to read the value of XX protection Free counter. */
#define TCM_REG_XX_FREE 0x50178
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
/* [RW 4] Load value for expiration credit cnt. CFC max number of
outstanding load requests for timers (expiration) context loading. */
#define TM_REG_EXP_CRDCNT_VAL 0x164238
-/* [RW 18] Linear0 Max active cid. */
+/* [RW 18] Linear0 Max active cid (in banks of 32 entries). */
#define TM_REG_LIN0_MAX_ACTIVE_CID 0x164048
/* [WB 64] Linear0 phy address. */
#define TM_REG_LIN0_PHY_ADDR 0x164270
#define TM_REG_TM_INT_STS 0x1640f0
/* [RW 8] The event id for aggregated interrupt 0 */
#define TSDM_REG_AGG_INT_EVENT_0 0x42038
+#define TSDM_REG_AGG_INT_EVENT_2 0x42040
+#define TSDM_REG_AGG_INT_EVENT_20 0x42088
+#define TSDM_REG_AGG_INT_EVENT_21 0x4208c
+#define TSDM_REG_AGG_INT_EVENT_22 0x42090
+#define TSDM_REG_AGG_INT_EVENT_23 0x42094
+#define TSDM_REG_AGG_INT_EVENT_24 0x42098
+#define TSDM_REG_AGG_INT_EVENT_25 0x4209c
+#define TSDM_REG_AGG_INT_EVENT_26 0x420a0
+#define TSDM_REG_AGG_INT_EVENT_27 0x420a4
+#define TSDM_REG_AGG_INT_EVENT_28 0x420a8
+#define TSDM_REG_AGG_INT_EVENT_29 0x420ac
+#define TSDM_REG_AGG_INT_EVENT_3 0x42044
+#define TSDM_REG_AGG_INT_EVENT_30 0x420b0
+#define TSDM_REG_AGG_INT_EVENT_31 0x420b4
+#define TSDM_REG_AGG_INT_EVENT_4 0x42048
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define TSDM_REG_CFC_RSP_START_ADDR 0x42008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RW 32] Interrupt mask register #0 read/write */
#define TSDM_REG_TSDM_INT_MASK_0 0x4229c
#define TSDM_REG_TSDM_INT_MASK_1 0x422ac
+/* [R 32] Interrupt register #0 read */
+#define TSDM_REG_TSDM_INT_STS_0 0x42290
+#define TSDM_REG_TSDM_INT_STS_1 0x422a0
/* [RW 11] Parity mask register #0 read/write */
#define TSDM_REG_TSDM_PRTY_MASK 0x422bc
/* [R 11] Parity register #0 read */
#define TSEM_REG_ENABLE_OUT 0x1800a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- TSEM_REGISTERS_FAST_MEMORY (Offset: 0x1a0000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define TSEM_REG_FAST_MEMORY 0x1a0000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define TSEM_REG_INT_TABLE 0x180400
+#define TSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define TSEM_REG_MSG_NUM_FIC0 0x180000
/* [RW 32] Interrupt mask register #0 read/write */
#define TSEM_REG_TSEM_INT_MASK_0 0x180100
#define TSEM_REG_TSEM_INT_MASK_1 0x180110
+/* [R 32] Interrupt register #0 read */
+#define TSEM_REG_TSEM_INT_STS_0 0x1800f4
+#define TSEM_REG_TSEM_INT_STS_1 0x180104
/* [RW 32] Parity mask register #0 read/write */
#define TSEM_REG_TSEM_PRTY_MASK_0 0x180120
#define TSEM_REG_TSEM_PRTY_MASK_1 0x180130
#define UCM_REG_N_SM_CTX_LD_2 0xe005c
#define UCM_REG_N_SM_CTX_LD_3 0xe0060
#define UCM_REG_N_SM_CTX_LD_4 0xe0064
-/* [RW 6] The physical queue number 0 per port index (CID[23]) */
+#define UCM_REG_N_SM_CTX_LD_5 0xe0068
#define UCM_REG_PHYS_QNUM0_0 0xe0110
#define UCM_REG_PHYS_QNUM0_1 0xe0114
-/* [RW 6] The physical queue number 1 per port index (CID[23]) */
#define UCM_REG_PHYS_QNUM1_0 0xe0118
#define UCM_REG_PHYS_QNUM1_1 0xe011c
+#define UCM_REG_PHYS_QNUM2_0 0xe0120
+#define UCM_REG_PHYS_QNUM2_1 0xe0124
+#define UCM_REG_PHYS_QNUM3_0 0xe0128
+#define UCM_REG_PHYS_QNUM3_1 0xe012c
/* [RW 8] The Event ID for Timers formatting in case of stop done. */
#define UCM_REG_STOP_EVNT_ID 0xe00ac
/* [RC 1] Set when the message length mismatch (relative to last indication)
#define UCM_REG_UCM_INT_MASK 0xe01d4
/* [R 11] Interrupt register #0 read */
#define UCM_REG_UCM_INT_STS 0xe01c8
+/* [R 27] Parity register #0 read */
+#define UCM_REG_UCM_PRTY_STS 0xe01d8
/* [RW 2] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
mechanism. The fields are:[5:0] - message length; 14:6] - message
pointer; 19:15] - next pointer. */
#define UCM_REG_XX_DESCR_TABLE 0xe0280
+#define UCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Use to read the XX protection Free counter. */
#define UCM_REG_XX_FREE 0xe016c
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
#define USDM_REG_AGG_INT_EVENT_17 0xc407c
#define USDM_REG_AGG_INT_EVENT_18 0xc4080
#define USDM_REG_AGG_INT_EVENT_19 0xc4084
+#define USDM_REG_AGG_INT_EVENT_2 0xc4040
+#define USDM_REG_AGG_INT_EVENT_20 0xc4088
+#define USDM_REG_AGG_INT_EVENT_21 0xc408c
+#define USDM_REG_AGG_INT_EVENT_22 0xc4090
+#define USDM_REG_AGG_INT_EVENT_23 0xc4094
+#define USDM_REG_AGG_INT_EVENT_24 0xc4098
+#define USDM_REG_AGG_INT_EVENT_25 0xc409c
+#define USDM_REG_AGG_INT_EVENT_26 0xc40a0
+#define USDM_REG_AGG_INT_EVENT_27 0xc40a4
+#define USDM_REG_AGG_INT_EVENT_28 0xc40a8
+#define USDM_REG_AGG_INT_EVENT_29 0xc40ac
+#define USDM_REG_AGG_INT_EVENT_3 0xc4044
+#define USDM_REG_AGG_INT_EVENT_30 0xc40b0
+#define USDM_REG_AGG_INT_EVENT_31 0xc40b4
+#define USDM_REG_AGG_INT_EVENT_4 0xc4048
/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
or auto-mask-mode (1) */
#define USDM_REG_AGG_INT_MODE_0 0xc41b8
/* [RW 32] Interrupt mask register #0 read/write */
#define USDM_REG_USDM_INT_MASK_0 0xc42a0
#define USDM_REG_USDM_INT_MASK_1 0xc42b0
+/* [R 32] Interrupt register #0 read */
+#define USDM_REG_USDM_INT_STS_0 0xc4294
+#define USDM_REG_USDM_INT_STS_1 0xc42a4
/* [RW 11] Parity mask register #0 read/write */
#define USDM_REG_USDM_PRTY_MASK 0xc42c0
/* [R 11] Parity register #0 read */
#define USEM_REG_ENABLE_OUT 0x3000a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers... the base address
- USEM_REGISTERS_FAST_MEMORY (Offset: 0x320000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define USEM_REG_FAST_MEMORY 0x320000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define USEM_REG_INT_TABLE 0x300400
+#define USEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define USEM_REG_MSG_NUM_FIC0 0x300000
/* [RW 32] Interrupt mask register #0 read/write */
#define USEM_REG_USEM_INT_MASK_0 0x300110
#define USEM_REG_USEM_INT_MASK_1 0x300120
+/* [R 32] Interrupt register #0 read */
+#define USEM_REG_USEM_INT_STS_0 0x300104
+#define USEM_REG_USEM_INT_STS_1 0x300114
/* [RW 32] Parity mask register #0 read/write */
#define USEM_REG_USEM_PRTY_MASK_0 0x300130
#define USEM_REG_USEM_PRTY_MASK_1 0x300140
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 64 at start-up. */
#define XCM_REG_FIC1_INIT_CRD 0x20410
-/* [RW 8] The maximum delayed ACK counter value.Must be at least 2. Per port
- value. */
#define XCM_REG_GLB_DEL_ACK_MAX_CNT_0 0x20118
#define XCM_REG_GLB_DEL_ACK_MAX_CNT_1 0x2011c
-/* [RW 28] The delayed ACK timeout in ticks. Per port value. */
#define XCM_REG_GLB_DEL_ACK_TMR_VAL_0 0x20108
#define XCM_REG_GLB_DEL_ACK_TMR_VAL_1 0x2010c
/* [RW 1] Arbitratiojn between Input Arbiter groups: 0 - fair Round-Robin; 1
#define XCM_REG_N_SM_CTX_LD_2 0x20068
#define XCM_REG_N_SM_CTX_LD_3 0x2006c
#define XCM_REG_N_SM_CTX_LD_4 0x20070
+#define XCM_REG_N_SM_CTX_LD_5 0x20074
/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_PBF_WEIGHT 0x200d0
+#define XCM_REG_PHYS_QNUM3_0 0x20100
+#define XCM_REG_PHYS_QNUM3_1 0x20104
/* [RW 8] The Event ID for Timers formatting in case of stop done. */
#define XCM_REG_STOP_EVNT_ID 0x200b8
/* [RC 1] Set at message length mismatch (relative to last indication) at
weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_USEM_WEIGHT 0x200c8
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD00 0x201d4
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD01 0x201d8
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD10 0x201dc
-/* [RW 2] DA counter command; used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_CMD11 0x201e0
-/* [RW 8] DA counter update value used in case of window update doorbell.The
- first index stands for the value DaEnable of that connection. The second
- index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL00 0x201e4
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL01 0x201e8
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL10 0x201ec
-/* [RW 8] DA counter update value; used in case of window update
- doorbell.The first index stands for the value DaEnable of that
- connection. The second index stands for port number. */
#define XCM_REG_WU_DA_CNT_UPD_VAL11 0x201f0
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00 0x201c4
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01 0x201c8
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10 0x201cc
-/* [RW 1] DA timer command; used in case of window update doorbell.The first
- index stands for the value DaEnable of that connection. The second index
- stands for port number. */
#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11 0x201d0
/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
#define XCM_REG_XCM_INT_MASK 0x202b4
/* [R 14] Interrupt register #0 read */
#define XCM_REG_XCM_INT_STS 0x202a8
+/* [R 30] Parity register #0 read */
+#define XCM_REG_XCM_PRTY_STS 0x202b8
/* [RW 4] The size of AG context region 0 in REG-pairs. Designates the MS
REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
Is used to determine the number of the AG context REG-pairs written back;
mechanism. The fields are: [5:0] - message length; 11:6] - message
pointer; 16:12] - next pointer. */
#define XCM_REG_XX_DESCR_TABLE 0x20480
+#define XCM_REG_XX_DESCR_TABLE_SIZE 32
/* [R 6] Used to read the XX protection Free counter. */
#define XCM_REG_XX_FREE 0x20240
/* [RW 6] Initial value for the credit counter; responsible for fulfilling
#define XCM_REG_XX_MSG_NUM 0x20428
/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
#define XCM_REG_XX_OVFL_EVNT_ID 0x20058
-/* [RW 15] Indirect access to the XX table of the XX protection mechanism.
+/* [RW 16] Indirect access to the XX table of the XX protection mechanism.
The fields are:[4:0] - tail pointer; 9:5] - Link List size; 14:10] -
header pointer. */
#define XCM_REG_XX_TABLE 0x20500
#define XSDM_REG_AGG_INT_EVENT_17 0x16607c
#define XSDM_REG_AGG_INT_EVENT_18 0x166080
#define XSDM_REG_AGG_INT_EVENT_19 0x166084
+#define XSDM_REG_AGG_INT_EVENT_10 0x166060
+#define XSDM_REG_AGG_INT_EVENT_11 0x166064
+#define XSDM_REG_AGG_INT_EVENT_12 0x166068
#define XSDM_REG_AGG_INT_EVENT_2 0x166040
#define XSDM_REG_AGG_INT_EVENT_20 0x166088
#define XSDM_REG_AGG_INT_EVENT_21 0x16608c
#define XSDM_REG_AGG_INT_EVENT_27 0x1660a4
#define XSDM_REG_AGG_INT_EVENT_28 0x1660a8
#define XSDM_REG_AGG_INT_EVENT_29 0x1660ac
+#define XSDM_REG_AGG_INT_EVENT_3 0x166044
+#define XSDM_REG_AGG_INT_EVENT_30 0x1660b0
+#define XSDM_REG_AGG_INT_EVENT_31 0x1660b4
+#define XSDM_REG_AGG_INT_EVENT_4 0x166048
+#define XSDM_REG_AGG_INT_EVENT_5 0x16604c
+#define XSDM_REG_AGG_INT_EVENT_6 0x166050
+#define XSDM_REG_AGG_INT_EVENT_7 0x166054
+#define XSDM_REG_AGG_INT_EVENT_8 0x166058
+#define XSDM_REG_AGG_INT_EVENT_9 0x16605c
/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
or auto-mask-mode (1) */
#define XSDM_REG_AGG_INT_MODE_0 0x1661b8
/* [RW 32] Interrupt mask register #0 read/write */
#define XSDM_REG_XSDM_INT_MASK_0 0x16629c
#define XSDM_REG_XSDM_INT_MASK_1 0x1662ac
+/* [R 32] Interrupt register #0 read */
+#define XSDM_REG_XSDM_INT_STS_0 0x166290
+#define XSDM_REG_XSDM_INT_STS_1 0x1662a0
/* [RW 11] Parity mask register #0 read/write */
#define XSDM_REG_XSDM_PRTY_MASK 0x1662bc
/* [R 11] Parity register #0 read */
#define XSEM_REG_ENABLE_OUT 0x2800a8
/* [RW 32] This address space contains all registers and memories that are
placed in SEM_FAST block. The SEM_FAST registers are described in
- appendix B. In order to access the SEM_FAST registers the base address
- XSEM_REGISTERS_FAST_MEMORY (Offset: 0x2a0000) should be added to each
- SEM_FAST register offset. */
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
#define XSEM_REG_FAST_MEMORY 0x2a0000
/* [RW 1] Disables input messages from FIC0 May be updated during run_time
by the microcode */
/* [RW 15] Interrupt table Read and write access to it is not possible in
the middle of the work */
#define XSEM_REG_INT_TABLE 0x280400
+#define XSEM_REG_INT_TABLE_SIZE 256
/* [ST 24] Statistics register. The number of messages that entered through
FIC0 */
#define XSEM_REG_MSG_NUM_FIC0 0x280000
/* [RW 32] Interrupt mask register #0 read/write */
#define XSEM_REG_XSEM_INT_MASK_0 0x280110
#define XSEM_REG_XSEM_INT_MASK_1 0x280120
+/* [R 32] Interrupt register #0 read */
+#define XSEM_REG_XSEM_INT_STS_0 0x280104
+#define XSEM_REG_XSEM_INT_STS_1 0x280114
/* [RW 32] Parity mask register #0 read/write */
#define XSEM_REG_XSEM_PRTY_MASK_0 0x280130
#define XSEM_REG_XSEM_PRTY_MASK_1 0x280140
#define BIGMAC_REGISTER_TX_SOURCE_ADDR (0x08<<3)
#define BIGMAC_REGISTER_TX_STAT_GTBYT (0x20<<3)
#define BIGMAC_REGISTER_TX_STAT_GTPKT (0x0C<<3)
+#define EMAC_LED_1000MB_OVERRIDE (1L<<1)
+#define EMAC_LED_100MB_OVERRIDE (1L<<2)
+#define EMAC_LED_10MB_OVERRIDE (1L<<3)
+#define EMAC_LED_2500MB_OVERRIDE (1L<<12)
+#define EMAC_LED_OVERRIDE (1L<<0)
+#define EMAC_LED_TRAFFIC (1L<<6)
#define EMAC_MDIO_COMM_COMMAND_ADDRESS (0L<<26)
-#define EMAC_MDIO_COMM_COMMAND_READ_22 (2L<<26)
#define EMAC_MDIO_COMM_COMMAND_READ_45 (3L<<26)
-#define EMAC_MDIO_COMM_COMMAND_WRITE_22 (1L<<26)
#define EMAC_MDIO_COMM_COMMAND_WRITE_45 (1L<<26)
#define EMAC_MDIO_COMM_DATA (0xffffL<<0)
#define EMAC_MDIO_COMM_START_BUSY (1L<<29)
#define EMAC_MODE_PORT_MII (1L<<2)
#define EMAC_MODE_PORT_MII_10M (3L<<2)
#define EMAC_MODE_RESET (1L<<0)
+#define EMAC_REG_EMAC_LED 0xc
#define EMAC_REG_EMAC_MAC_MATCH 0x10
#define EMAC_REG_EMAC_MDIO_COMM 0xac
#define EMAC_REG_EMAC_MDIO_MODE 0xb4
#define EMAC_RX_MODE_PROMISCUOUS (1L<<8)
#define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31)
#define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3)
-#define EMAC_TX_MODE_RESET (1L<<0)
+#define MISC_REGISTERS_GPIO_0 0
#define MISC_REGISTERS_GPIO_1 1
#define MISC_REGISTERS_GPIO_2 2
#define MISC_REGISTERS_GPIO_3 3
#define MISC_REGISTERS_GPIO_CLR_POS 16
#define MISC_REGISTERS_GPIO_FLOAT (0xffL<<24)
#define MISC_REGISTERS_GPIO_FLOAT_POS 24
+#define MISC_REGISTERS_GPIO_HIGH 1
#define MISC_REGISTERS_GPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_GPIO_LOW 0
#define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1
#define MISC_REGISTERS_GPIO_OUTPUT_LOW 0
#define MISC_REGISTERS_GPIO_PORT_SHIFT 4
#define AEU_INPUTS_ATTN_BITS_XSEMI_PARITY_ERROR (1<<10)
#define RESERVED_GENERAL_ATTENTION_BIT_0 0
-#define EVEREST_GEN_ATTN_IN_USE_MASK 0x3e0
+#define EVEREST_GEN_ATTN_IN_USE_MASK 0x3ffe0
#define EVEREST_LATCHED_ATTN_IN_USE_MASK 0xffe00000
#define RESERVED_GENERAL_ATTENTION_BIT_6 6
/* mcp error attention bit */
#define MCP_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_11
+/*E1H NIG status sync attention mapped to group 4-7*/
+#define LINK_SYNC_ATTENTION_BIT_FUNC_0 RESERVED_GENERAL_ATTENTION_BIT_12
+#define LINK_SYNC_ATTENTION_BIT_FUNC_1 RESERVED_GENERAL_ATTENTION_BIT_13
+#define LINK_SYNC_ATTENTION_BIT_FUNC_2 RESERVED_GENERAL_ATTENTION_BIT_14
+#define LINK_SYNC_ATTENTION_BIT_FUNC_3 RESERVED_GENERAL_ATTENTION_BIT_15
+#define LINK_SYNC_ATTENTION_BIT_FUNC_4 RESERVED_GENERAL_ATTENTION_BIT_16
+#define LINK_SYNC_ATTENTION_BIT_FUNC_5 RESERVED_GENERAL_ATTENTION_BIT_17
+#define LINK_SYNC_ATTENTION_BIT_FUNC_6 RESERVED_GENERAL_ATTENTION_BIT_18
+#define LINK_SYNC_ATTENTION_BIT_FUNC_7 RESERVED_GENERAL_ATTENTION_BIT_19
+
+
#define LATCHED_ATTN_RBCR 23
#define LATCHED_ATTN_RBCT 24
#define LATCHED_ATTN_RBCN 25
#define PCICFG_OFFSET 0x2000
#define PCICFG_VENDOR_ID_OFFSET 0x00
#define PCICFG_DEVICE_ID_OFFSET 0x02
-#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
-#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
-#define PCICFG_INT_LINE 0x3c
-#define PCICFG_INT_PIN 0x3d
+#define PCICFG_COMMAND_OFFSET 0x04
+#define PCICFG_STATUS_OFFSET 0x06
+#define PCICFG_REVESION_ID 0x08
#define PCICFG_CACHE_LINE_SIZE 0x0c
#define PCICFG_LATENCY_TIMER 0x0d
-#define PCICFG_REVESION_ID 0x08
-#define PCICFG_BAR_1_LOW 0x10
-#define PCICFG_BAR_1_HIGH 0x14
-#define PCICFG_BAR_2_LOW 0x18
-#define PCICFG_BAR_2_HIGH 0x1c
-#define PCICFG_GRC_ADDRESS 0x78
-#define PCICFG_GRC_DATA 0x80
+#define PCICFG_BAR_1_LOW 0x10
+#define PCICFG_BAR_1_HIGH 0x14
+#define PCICFG_BAR_2_LOW 0x18
+#define PCICFG_BAR_2_HIGH 0x1c
+#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
+#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
+#define PCICFG_INT_LINE 0x3c
+#define PCICFG_INT_PIN 0x3d
+#define PCICFG_PM_CSR_OFFSET 0x4c
+#define PCICFG_GRC_ADDRESS 0x78
+#define PCICFG_GRC_DATA 0x80
#define PCICFG_DEVICE_CONTROL 0xb4
#define PCICFG_LINK_CONTROL 0xbc
+#define PCICFG_COMMAND_IO_SPACE (1<<0)
+#define PCICFG_COMMAND_MEM_SPACE (1<<1)
+#define PCICFG_COMMAND_BUS_MASTER (1<<2)
+#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3)
+#define PCICFG_COMMAND_MWI_CYCLES (1<<4)
+#define PCICFG_COMMAND_VGA_SNOOP (1<<5)
+#define PCICFG_COMMAND_PERR_ENA (1<<6)
+#define PCICFG_COMMAND_STEPPING (1<<7)
+#define PCICFG_COMMAND_SERR_ENA (1<<8)
+#define PCICFG_COMMAND_FAST_B2B (1<<9)
+#define PCICFG_COMMAND_INT_DISABLE (1<<10)
+#define PCICFG_COMMAND_RESERVED (0x1f<<11)
+
+#define PCICFG_PM_CSR_STATE (0x3<<0)
+#define PCICFG_PM_CSR_PME_STATUS (1<<15)
+
#define BAR_USTRORM_INTMEM 0x400000
#define BAR_CSTRORM_INTMEM 0x410000
#define BAR_XSTRORM_INTMEM 0x420000
#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_MAIN_RST 0x8000
#define MDIO_REG_BANK_CL73_IEEEB1 0x10
-#define MDIO_CL73_IEEEB1_AN_ADV2 0x01
+#define MDIO_CL73_IEEEB1_AN_ADV2 0x01
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M 0x0000
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX 0x0020
#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 0x0040
#define MDIO_REG_BANK_RX_ALL 0x80f0
#define MDIO_RX_ALL_RX_EQ_BOOST 0x1c
#define MDIO_RX_ALL_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
-#define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10
+#define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10
#define MDIO_REG_BANK_TX0 0x8060
#define MDIO_TX0_TX_DRIVER 0x17
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP 0x10
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE 0x8000
#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE 0x4000
-#define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11
+#define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11
#define MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE 0x8000
-#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14
#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS 0x0001
#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS 0x0010
-#define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15
+#define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15
#define MDIO_REG_BANK_GP_STATUS 0x8120
-#define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020
-
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00
-#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00
#define MDIO_REG_BANK_10G_PARALLEL_DETECT 0x8130
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13
-#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1)
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1)
#define MDIO_REG_BANK_SERDES_DIGITAL 0x8300
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001
-#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008
-#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1 0x18
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000
-#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008
-#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1 0x18
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009
#define MDIO_REG_BANK_OVER_1G 0x8320
-#define MDIO_OVER_1G_DIGCTL_3_4 0x14
-#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0
-#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5
-#define MDIO_OVER_1G_UP1 0x19
-#define MDIO_OVER_1G_UP1_2_5G 0x0001
-#define MDIO_OVER_1G_UP1_5G 0x0002
-#define MDIO_OVER_1G_UP1_6G 0x0004
-#define MDIO_OVER_1G_UP1_10G 0x0010
-#define MDIO_OVER_1G_UP1_10GH 0x0008
-#define MDIO_OVER_1G_UP1_12G 0x0020
-#define MDIO_OVER_1G_UP1_12_5G 0x0040
-#define MDIO_OVER_1G_UP1_13G 0x0080
-#define MDIO_OVER_1G_UP1_15G 0x0100
-#define MDIO_OVER_1G_UP1_16G 0x0200
-#define MDIO_OVER_1G_UP2 0x1A
-#define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007
-#define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038
-#define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0
-#define MDIO_OVER_1G_UP3 0x1B
-#define MDIO_OVER_1G_UP3_HIGIG2 0x0001
-#define MDIO_OVER_1G_LP_UP1 0x1C
-#define MDIO_OVER_1G_LP_UP2 0x1D
-#define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff
-#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780
-#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7
-#define MDIO_OVER_1G_LP_UP3 0x1E
+#define MDIO_OVER_1G_DIGCTL_3_4 0x14
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5
+#define MDIO_OVER_1G_UP1 0x19
+#define MDIO_OVER_1G_UP1_2_5G 0x0001
+#define MDIO_OVER_1G_UP1_5G 0x0002
+#define MDIO_OVER_1G_UP1_6G 0x0004
+#define MDIO_OVER_1G_UP1_10G 0x0010
+#define MDIO_OVER_1G_UP1_10GH 0x0008
+#define MDIO_OVER_1G_UP1_12G 0x0020
+#define MDIO_OVER_1G_UP1_12_5G 0x0040
+#define MDIO_OVER_1G_UP1_13G 0x0080
+#define MDIO_OVER_1G_UP1_15G 0x0100
+#define MDIO_OVER_1G_UP1_16G 0x0200
+#define MDIO_OVER_1G_UP2 0x1A
+#define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007
+#define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038
+#define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0
+#define MDIO_OVER_1G_UP3 0x1B
+#define MDIO_OVER_1G_UP3_HIGIG2 0x0001
+#define MDIO_OVER_1G_LP_UP1 0x1C
+#define MDIO_OVER_1G_LP_UP2 0x1D
+#define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7
+#define MDIO_OVER_1G_LP_UP3 0x1E
#define MDIO_REG_BANK_BAM_NEXT_PAGE 0x8350
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001
-#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002
+
+#define MDIO_REG_BANK_CL73_USERB0 0x8370
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001
+
+#define MDIO_REG_BANK_AER_BLOCK 0xFFD0
+#define MDIO_AER_BLOCK_AER_REG 0x1E
+
+#define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0
+#define MDIO_COMBO_IEEE0_MII_CONTROL 0x10
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040
+#define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200
+#define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000
+#define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000
+#define MDIO_COMBO_IEEE0_MII_STATUS 0x11
+#define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004
+#define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020
+/*WhenthelinkpartnerisinSGMIImode(bit0=1),then
+bit15=link,bit12=duplex,bits11:10=speed,bit14=acknowledge.
+Theotherbitsarereservedandshouldbezero*/
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001
+
+
+#define MDIO_PMA_DEVAD 0x1
+/*ieee*/
+#define MDIO_PMA_REG_CTRL 0x0
+#define MDIO_PMA_REG_STATUS 0x1
+#define MDIO_PMA_REG_10G_CTRL2 0x7
+#define MDIO_PMA_REG_RX_SD 0xa
+/*bcm*/
+#define MDIO_PMA_REG_BCM_CTRL 0x0096
+#define MDIO_PMA_REG_FEC_CTRL 0x00ab
+#define MDIO_PMA_REG_RX_ALARM_CTRL 0x9000
+#define MDIO_PMA_REG_LASI_CTRL 0x9002
+#define MDIO_PMA_REG_RX_ALARM 0x9003
+#define MDIO_PMA_REG_TX_ALARM 0x9004
+#define MDIO_PMA_REG_LASI_STATUS 0x9005
+#define MDIO_PMA_REG_PHY_IDENTIFIER 0xc800
+#define MDIO_PMA_REG_DIGITAL_CTRL 0xc808
+#define MDIO_PMA_REG_DIGITAL_STATUS 0xc809
+#define MDIO_PMA_REG_TX_POWER_DOWN 0xca02
+#define MDIO_PMA_REG_CMU_PLL_BYPASS 0xca09
+#define MDIO_PMA_REG_MISC_CTRL 0xca0a
+#define MDIO_PMA_REG_GEN_CTRL 0xca10
+#define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188
+#define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a
+#define MDIO_PMA_REG_ROM_VER1 0xca19
+#define MDIO_PMA_REG_ROM_VER2 0xca1a
+#define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b
+#define MDIO_PMA_REG_PLL_BANDWIDTH 0xca1d
+#define MDIO_PMA_REG_CDR_BANDWIDTH 0xca46
+#define MDIO_PMA_REG_MISC_CTRL1 0xca85
+
+#define MDIO_PMA_REG_7101_RESET 0xc000
+#define MDIO_PMA_REG_7107_LED_CNTL 0xc007
+#define MDIO_PMA_REG_7101_VER1 0xc026
+#define MDIO_PMA_REG_7101_VER2 0xc027
+
+
+#define MDIO_WIS_DEVAD 0x2
+/*bcm*/
+#define MDIO_WIS_REG_LASI_CNTL 0x9002
+#define MDIO_WIS_REG_LASI_STATUS 0x9005
+
+#define MDIO_PCS_DEVAD 0x3
+#define MDIO_PCS_REG_STATUS 0x0020
+#define MDIO_PCS_REG_LASI_STATUS 0x9005
+#define MDIO_PCS_REG_7101_DSP_ACCESS 0xD000
+#define MDIO_PCS_REG_7101_SPI_MUX 0xD008
+#define MDIO_PCS_REG_7101_SPI_CTRL_ADDR 0xE12A
+#define MDIO_PCS_REG_7101_SPI_RESET_BIT (5)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR 0xE02A
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_WRITE_ENABLE_CMD (6)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_BULK_ERASE_CMD (0xC7)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_PAGE_PROGRAM_CMD (2)
+#define MDIO_PCS_REG_7101_SPI_BYTES_TO_TRANSFER_ADDR 0xE028
+
-#define MDIO_REG_BANK_CL73_USERB0 0x8370
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14
-#define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001
+#define MDIO_XS_DEVAD 0x4
+#define MDIO_XS_PLL_SEQUENCER 0x8000
+#define MDIO_XS_SFX7101_XGXS_TEST1 0xc00a
-#define MDIO_REG_BANK_AER_BLOCK 0xFFD0
-#define MDIO_AER_BLOCK_AER_REG 0x1E
+#define MDIO_AN_DEVAD 0x7
+/*ieee*/
+#define MDIO_AN_REG_CTRL 0x0000
+#define MDIO_AN_REG_STATUS 0x0001
+#define MDIO_AN_REG_STATUS_AN_COMPLETE 0x0020
+#define MDIO_AN_REG_ADV_PAUSE 0x0010
+#define MDIO_AN_REG_ADV_PAUSE_PAUSE 0x0400
+#define MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC 0x0800
+#define MDIO_AN_REG_ADV_PAUSE_BOTH 0x0C00
+#define MDIO_AN_REG_ADV_PAUSE_MASK 0x0C00
+#define MDIO_AN_REG_ADV 0x0011
+#define MDIO_AN_REG_ADV2 0x0012
+#define MDIO_AN_REG_LP_AUTO_NEG 0x0013
+#define MDIO_AN_REG_MASTER_STATUS 0x0021
+/*bcm*/
+#define MDIO_AN_REG_LINK_STATUS 0x8304
+#define MDIO_AN_REG_CL37_CL73 0x8370
+#define MDIO_AN_REG_CL37_AN 0xffe0
+#define MDIO_AN_REG_CL37_FD 0xffe4
-#define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0
-#define MDIO_COMBO_IEEE0_MII_CONTROL 0x10
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000
-#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040
-#define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100
-#define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200
-#define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000
-#define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000
-#define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000
-#define MDIO_COMBO_IEEE0_MII_STATUS 0x11
-#define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004
-#define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE\
- 0x0000
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH\
- 0x0180
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020
-#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001
+#define IGU_FUNC_BASE 0x0400
-#define EXT_PHY_AUTO_NEG_DEVAD 0x7
-#define EXT_PHY_OPT_PMA_PMD_DEVAD 0x1
-#define EXT_PHY_OPT_WIS_DEVAD 0x2
-#define EXT_PHY_OPT_PCS_DEVAD 0x3
-#define EXT_PHY_OPT_PHY_XS_DEVAD 0x4
-#define EXT_PHY_OPT_CNTL 0x0
-#define EXT_PHY_OPT_CNTL2 0x7
-#define EXT_PHY_OPT_PMD_RX_SD 0xa
-#define EXT_PHY_OPT_PMD_MISC_CNTL 0xca0a
-#define EXT_PHY_OPT_PHY_IDENTIFIER 0xc800
-#define EXT_PHY_OPT_PMD_DIGITAL_CNT 0xc808
-#define EXT_PHY_OPT_PMD_DIGITAL_SATUS 0xc809
-#define EXT_PHY_OPT_CMU_PLL_BYPASS 0xca09
-#define EXT_PHY_OPT_LASI_CNTL 0x9002
-#define EXT_PHY_OPT_RX_ALARM 0x9003
-#define EXT_PHY_OPT_LASI_STATUS 0x9005
-#define EXT_PHY_OPT_PCS_STATUS 0x0020
-#define EXT_PHY_OPT_XGXS_LANE_STATUS 0x0018
-#define EXT_PHY_OPT_AN_LINK_STATUS 0x8304
-#define EXT_PHY_OPT_AN_CL37_CL73 0x8370
-#define EXT_PHY_OPT_AN_CL37_FD 0xffe4
-#define EXT_PHY_OPT_AN_CL37_AN 0xffe0
-#define EXT_PHY_OPT_AN_ADV 0x11
+#define IGU_ADDR_MSIX 0x0000
+#define IGU_ADDR_INT_ACK 0x0200
+#define IGU_ADDR_PROD_UPD 0x0201
+#define IGU_ADDR_ATTN_BITS_UPD 0x0202
+#define IGU_ADDR_ATTN_BITS_SET 0x0203
+#define IGU_ADDR_ATTN_BITS_CLR 0x0204
+#define IGU_ADDR_COALESCE_NOW 0x0205
+#define IGU_ADDR_SIMD_MASK 0x0206
+#define IGU_ADDR_SIMD_NOMASK 0x0207
+#define IGU_ADDR_MSI_CTL 0x0210
+#define IGU_ADDR_MSI_ADDR_LO 0x0211
+#define IGU_ADDR_MSI_ADDR_HI 0x0212
+#define IGU_ADDR_MSI_DATA 0x0213
-#define EXT_PHY_KR_PMA_PMD_DEVAD 0x1
-#define EXT_PHY_KR_PCS_DEVAD 0x3
-#define EXT_PHY_KR_AUTO_NEG_DEVAD 0x7
-#define EXT_PHY_KR_CTRL 0x0000
-#define EXT_PHY_KR_STATUS 0x0001
-#define EXT_PHY_KR_AUTO_NEG_COMPLETE 0x0020
-#define EXT_PHY_KR_AUTO_NEG_ADVERT 0x0010
-#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE 0x0400
-#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_ASYMMETRIC 0x0800
-#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_BOTH 0x0C00
-#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_MASK 0x0C00
-#define EXT_PHY_KR_LP_AUTO_NEG 0x0013
-#define EXT_PHY_KR_CTRL2 0x0007
-#define EXT_PHY_KR_PCS_STATUS 0x0020
-#define EXT_PHY_KR_PMD_CTRL 0x0096
-#define EXT_PHY_KR_LASI_CNTL 0x9002
-#define EXT_PHY_KR_LASI_STATUS 0x9005
-#define EXT_PHY_KR_MISC_CTRL1 0xca85
-#define EXT_PHY_KR_GEN_CTRL 0xca10
-#define EXT_PHY_KR_ROM_CODE 0xca19
-#define EXT_PHY_KR_ROM_RESET_INTERNAL_MP 0x0188
-#define EXT_PHY_KR_ROM_MICRO_RESET 0x018a
+#define IGU_INT_ENABLE 0
+#define IGU_INT_DISABLE 1
+#define IGU_INT_NOP 2
+#define IGU_INT_NOP2 3
-#define EXT_PHY_SFX7101_XGXS_TEST1 0xc00a
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff