[netdrvr gianfar] use new phy layer
authorAndy Fleming <afleming@freescale.com>
Sat, 24 Sep 2005 02:54:21 +0000 (22:54 -0400)
committerJeff Garzik <jgarzik@pobox.com>
Sat, 24 Sep 2005 02:54:21 +0000 (22:54 -0400)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/Kconfig
drivers/net/Makefile
drivers/net/gianfar.c
drivers/net/gianfar.h
drivers/net/gianfar_ethtool.c
drivers/net/gianfar_mii.c [new file with mode: 0644]
drivers/net/gianfar_mii.h [new file with mode: 0644]
drivers/net/gianfar_phy.c [deleted file]
drivers/net/gianfar_phy.h [deleted file]

index ff3fccd7513b59a4a39895d5f56ddc3bdda3124c..4739a63601ebd1a8c9c1903beb61792453dc0686 100644 (file)
@@ -2075,6 +2075,8 @@ config SPIDER_NET
 config GIANFAR
        tristate "Gianfar Ethernet"
        depends on 85xx || 83xx
+       select PHYLIB
+       select PHYCONTROL
        help
          This driver supports the Gigabit TSEC on the MPC85xx 
          family of chips, and the FEC on the 8540
index e6acba68923aea866edf662b3a47c1d66bd566bc..39b17cb4f86e638da28abd7dc62b96643b8ee357 100644 (file)
@@ -13,7 +13,7 @@ obj-$(CONFIG_CHELSIO_T1) += chelsio/
 obj-$(CONFIG_BONDING) += bonding/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 
-gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_phy.o
+gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_mii.o
 
 #
 # link order important here
index 6518334b92801a41745718b09a74805e3e7b8004..ae5a2ed3b2640336a656087596206d2e462ee73e 100644 (file)
  *  define the configuration needed by the board are defined in a
  *  board structure in arch/ppc/platforms (though I do not
  *  discount the possibility that other architectures could one
- *  day be supported.  One assumption the driver currently makes
- *  is that the PHY is configured in such a way to advertise all
- *  capabilities.  This is a sensible default, and on certain
- *  PHYs, changing this default encounters substantial errata
- *  issues.  Future versions may remove this requirement, but for
- *  now, it is best for the firmware to ensure this is the case.
+ *  day be supported.
  *
  *  The Gianfar Ethernet Controller uses a ring of buffer
  *  descriptors.  The beginning is indicated by a register
@@ -47,7 +42,7 @@
  *  corresponding bit in the IMASK register is also set (if
  *  interrupt coalescing is active, then the interrupt may not
  *  happen immediately, but will wait until either a set number
- *  of frames or amount of time have passed.).  In NAPI, the
+ *  of frames or amount of time have passed).  In NAPI, the
  *  interrupt handler will signal there is work to be done, and
  *  exit.  Without NAPI, the packet(s) will be handled
  *  immediately.  Both methods will start at the last known empty
@@ -75,6 +70,7 @@
 #include <linux/sched.h>
 #include <linux/string.h>
 #include <linux/errno.h>
+#include <linux/unistd.h>
 #include <linux/slab.h>
 #include <linux/interrupt.h>
 #include <linux/init.h>
 #include <linux/version.h>
 #include <linux/dma-mapping.h>
 #include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
 
 #include "gianfar.h"
-#include "gianfar_phy.h"
+#include "gianfar_mii.h"
 
 #define TX_TIMEOUT      (1*HZ)
 #define SKB_ALLOC_TIMEOUT 1000000
 #endif
 
 const char gfar_driver_name[] = "Gianfar Ethernet";
-const char gfar_driver_version[] = "1.1";
+const char gfar_driver_version[] = "1.2";
 
-int startup_gfar(struct net_device *dev);
 static int gfar_enet_open(struct net_device *dev);
 static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev);
 static void gfar_timeout(struct net_device *dev);
@@ -126,17 +123,13 @@ static int gfar_set_mac_address(struct net_device *dev);
 static int gfar_change_mtu(struct net_device *dev, int new_mtu);
 static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs);
 static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs);
-static irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs);
 static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static void gfar_phy_change(void *data);
-static void gfar_phy_timer(unsigned long data);
 static void adjust_link(struct net_device *dev);
 static void init_registers(struct net_device *dev);
 static int init_phy(struct net_device *dev);
 static int gfar_probe(struct device *device);
 static int gfar_remove(struct device *device);
-void free_skb_resources(struct gfar_private *priv);
+static void free_skb_resources(struct gfar_private *priv);
 static void gfar_set_multi(struct net_device *dev);
 static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
 #ifdef CONFIG_GFAR_NAPI
@@ -144,7 +137,6 @@ static int gfar_poll(struct net_device *dev, int *budget);
 #endif
 int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
 static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int length);
-static void gfar_phy_startup_timer(unsigned long data);
 static void gfar_vlan_rx_register(struct net_device *netdev,
                                struct vlan_group *grp);
 static void gfar_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
@@ -162,6 +154,9 @@ int gfar_uses_fcb(struct gfar_private *priv)
        else
                return 0;
 }
+
+/* Set up the ethernet device structure, private data,
+ * and anything else we need before we start */
 static int gfar_probe(struct device *device)
 {
        u32 tempval;
@@ -175,7 +170,7 @@ static int gfar_probe(struct device *device)
 
        einfo = (struct gianfar_platform_data *) pdev->dev.platform_data;
 
-       if (einfo == NULL) {
+       if (NULL == einfo) {
                printk(KERN_ERR "gfar %d: Missing additional data!\n",
                       pdev->id);
 
@@ -185,7 +180,7 @@ static int gfar_probe(struct device *device)
        /* Create an ethernet device instance */
        dev = alloc_etherdev(sizeof (*priv));
 
-       if (dev == NULL)
+       if (NULL == dev)
                return -ENOMEM;
 
        priv = netdev_priv(dev);
@@ -207,20 +202,11 @@ static int gfar_probe(struct device *device)
        priv->regs = (struct gfar *)
                ioremap(r->start, sizeof (struct gfar));
 
-       if (priv->regs == NULL) {
+       if (NULL == priv->regs) {
                err = -ENOMEM;
                goto regs_fail;
        }
 
-       /* Set the PHY base address */
-       priv->phyregs = (struct gfar *)
-           ioremap(einfo->phy_reg_addr, sizeof (struct gfar));
-
-       if (priv->phyregs == NULL) {
-               err = -ENOMEM;
-               goto phy_regs_fail;
-       }
-
        spin_lock_init(&priv->lock);
 
        dev_set_drvdata(device, dev);
@@ -386,12 +372,10 @@ static int gfar_probe(struct device *device)
        return 0;
 
 register_fail:
-       iounmap((void *) priv->phyregs);
-phy_regs_fail:
        iounmap((void *) priv->regs);
 regs_fail:
        free_netdev(dev);
-       return -ENOMEM;
+       return err;
 }
 
 static int gfar_remove(struct device *device)
@@ -402,108 +386,41 @@ static int gfar_remove(struct device *device)
        dev_set_drvdata(device, NULL);
 
        iounmap((void *) priv->regs);
-       iounmap((void *) priv->phyregs);
        free_netdev(dev);
 
        return 0;
 }
 
 
-/* Configure the PHY for dev.
- * returns 0 if success.  -1 if failure
+/* Initializes driver's PHY state, and attaches to the PHY.
+ * Returns 0 on success.
  */
 static int init_phy(struct net_device *dev)
 {
        struct gfar_private *priv = netdev_priv(dev);
-       struct phy_info *curphy;
-       unsigned int timeout = PHY_INIT_TIMEOUT;
-       struct gfar *phyregs = priv->phyregs;
-       struct gfar_mii_info *mii_info;
-       int err;
+       uint gigabit_support =
+               priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
+               SUPPORTED_1000baseT_Full : 0;
+       struct phy_device *phydev;
 
        priv->oldlink = 0;
        priv->oldspeed = 0;
        priv->oldduplex = -1;
 
-       mii_info = kmalloc(sizeof(struct gfar_mii_info),
-                       GFP_KERNEL);
-
-       if(NULL == mii_info) {
-               if (netif_msg_ifup(priv))
-                       printk(KERN_ERR "%s: Could not allocate mii_info\n",
-                                       dev->name);
-               return -ENOMEM;
-       }
-
-       mii_info->speed = SPEED_1000;
-       mii_info->duplex = DUPLEX_FULL;
-       mii_info->pause = 0;
-       mii_info->link = 1;
-
-       mii_info->advertising = (ADVERTISED_10baseT_Half |
-                       ADVERTISED_10baseT_Full |
-                       ADVERTISED_100baseT_Half |
-                       ADVERTISED_100baseT_Full |
-                       ADVERTISED_1000baseT_Full);
-       mii_info->autoneg = 1;
+       phydev = phy_connect(dev, priv->einfo->bus_id, &adjust_link, 0);
 
-       spin_lock_init(&mii_info->mdio_lock);
-
-       mii_info->mii_id = priv->einfo->phyid;
-
-       mii_info->dev = dev;
-
-       mii_info->mdio_read = &read_phy_reg;
-       mii_info->mdio_write = &write_phy_reg;
-
-       priv->mii_info = mii_info;
-
-       /* Reset the management interface */
-       gfar_write(&phyregs->miimcfg, MIIMCFG_RESET);
-
-       /* Setup the MII Mgmt clock speed */
-       gfar_write(&phyregs->miimcfg, MIIMCFG_INIT_VALUE);
-
-       /* Wait until the bus is free */
-       while ((gfar_read(&phyregs->miimind) & MIIMIND_BUSY) &&
-                       timeout--)
-               cpu_relax();
-
-       if(timeout <= 0) {
-               printk(KERN_ERR "%s: The MII Bus is stuck!\n",
-                               dev->name);
-               err = -1;
-               goto bus_fail;
-       }
-
-       /* get info for this PHY */
-       curphy = get_phy_info(priv->mii_info);
-
-       if (curphy == NULL) {
-               if (netif_msg_ifup(priv))
-                       printk(KERN_ERR "%s: No PHY found\n", dev->name);
-               err = -1;
-               goto no_phy;
+       if (IS_ERR(phydev)) {
+               printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+               return PTR_ERR(phydev);
        }
 
-       mii_info->phyinfo = curphy;
+       /* Remove any features not supported by the controller */
+       phydev->supported &= (GFAR_SUPPORTED | gigabit_support);
+       phydev->advertising = phydev->supported;
 
-       /* Run the commands which initialize the PHY */
-       if(curphy->init) {
-               err = curphy->init(priv->mii_info);
-
-               if (err)
-                       goto phy_init_fail;
-       }
+       priv->phydev = phydev;
 
        return 0;
-
-phy_init_fail:
-no_phy:
-bus_fail:
-       kfree(mii_info);
-
-       return err;
 }
 
 static void init_registers(struct net_device *dev)
@@ -603,24 +520,13 @@ void stop_gfar(struct net_device *dev)
        struct gfar *regs = priv->regs;
        unsigned long flags;
 
+       phy_stop(priv->phydev);
+
        /* Lock it down */
        spin_lock_irqsave(&priv->lock, flags);
 
-       /* Tell the kernel the link is down */
-       priv->mii_info->link = 0;
-       adjust_link(dev);
-
        gfar_halt(dev);
 
-       if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
-               /* Clear any pending interrupts */
-               mii_clear_phy_interrupt(priv->mii_info);
-
-               /* Disable PHY Interrupts */
-               mii_configure_phy_interrupt(priv->mii_info,
-                               MII_INTERRUPT_DISABLED);
-       }
-
        spin_unlock_irqrestore(&priv->lock, flags);
 
        /* Free the IRQs */
@@ -629,13 +535,7 @@ void stop_gfar(struct net_device *dev)
                free_irq(priv->interruptTransmit, dev);
                free_irq(priv->interruptReceive, dev);
        } else {
-               free_irq(priv->interruptTransmit, dev);
-       }
-
-       if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
-               free_irq(priv->einfo->interruptPHY, dev);
-       } else {
-               del_timer_sync(&priv->phy_info_timer);
+               free_irq(priv->interruptTransmit, dev);
        }
 
        free_skb_resources(priv);
@@ -649,7 +549,7 @@ void stop_gfar(struct net_device *dev)
 
 /* If there are any tx skbs or rx skbs still around, free them.
  * Then free tx_skbuff and rx_skbuff */
-void free_skb_resources(struct gfar_private *priv)
+static void free_skb_resources(struct gfar_private *priv)
 {
        struct rxbd8 *rxbdp;
        struct txbd8 *txbdp;
@@ -770,7 +670,7 @@ int startup_gfar(struct net_device *dev)
            (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
                                        priv->tx_ring_size, GFP_KERNEL);
 
-       if (priv->tx_skbuff == NULL) {
+       if (NULL == priv->tx_skbuff) {
                if (netif_msg_ifup(priv))
                        printk(KERN_ERR "%s: Could not allocate tx_skbuff\n",
                                        dev->name);
@@ -785,7 +685,7 @@ int startup_gfar(struct net_device *dev)
            (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
                                        priv->rx_ring_size, GFP_KERNEL);
 
-       if (priv->rx_skbuff == NULL) {
+       if (NULL == priv->rx_skbuff) {
                if (netif_msg_ifup(priv))
                        printk(KERN_ERR "%s: Could not allocate rx_skbuff\n",
                                        dev->name);
@@ -879,13 +779,7 @@ int startup_gfar(struct net_device *dev)
                }
        }
 
-       /* Set up the PHY change work queue */
-       INIT_WORK(&priv->tq, gfar_phy_change, dev);
-
-       init_timer(&priv->phy_info_timer);
-       priv->phy_info_timer.function = &gfar_phy_startup_timer;
-       priv->phy_info_timer.data = (unsigned long) priv->mii_info;
-       mod_timer(&priv->phy_info_timer, jiffies + HZ);
+       phy_start(priv->phydev);
 
        /* Configure the coalescing support */
        if (priv->txcoalescing)
@@ -933,11 +827,6 @@ tx_skb_fail:
                        priv->tx_bd_base,
                        gfar_read(&regs->tbase0));
 
-       if (priv->mii_info->phyinfo->close)
-               priv->mii_info->phyinfo->close(priv->mii_info);
-
-       kfree(priv->mii_info);
-
        return err;
 }
 
@@ -1035,7 +924,7 @@ static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev)
        txbdp->status &= TXBD_WRAP;
 
        /* Set up checksumming */
-       if ((dev->features & NETIF_F_IP_CSUM) 
+       if ((dev->features & NETIF_F_IP_CSUM)
                        && (CHECKSUM_HW == skb->ip_summed)) {
                fcb = gfar_add_fcb(skb, txbdp);
                gfar_tx_checksum(skb, fcb);
@@ -1103,11 +992,9 @@ static int gfar_close(struct net_device *dev)
        struct gfar_private *priv = netdev_priv(dev);
        stop_gfar(dev);
 
-       /* Shutdown the PHY */
-       if (priv->mii_info->phyinfo->close)
-               priv->mii_info->phyinfo->close(priv->mii_info);
-
-       kfree(priv->mii_info);
+       /* Disconnect from the PHY */
+       phy_disconnect(priv->phydev);
+       priv->phydev = NULL;
 
        netif_stop_queue(dev);
 
@@ -1343,7 +1230,7 @@ struct sk_buff * gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp)
        while ((!skb) && timeout--)
                skb = dev_alloc_skb(priv->rx_buffer_size + RXBUF_ALIGNMENT);
 
-       if (skb == NULL)
+       if (NULL == skb)
                return NULL;
 
        /* We need the data buffer to be aligned properly.  We will reserve
@@ -1490,7 +1377,7 @@ static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb,
        struct gfar_private *priv = netdev_priv(dev);
        struct rxfcb *fcb = NULL;
 
-       if (skb == NULL) {
+       if (NULL == skb) {
                if (netif_msg_rx_err(priv))
                        printk(KERN_WARNING "%s: Missing skb!!.\n", dev->name);
                priv->stats.rx_dropped++;
@@ -1718,131 +1605,9 @@ static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs)
        return IRQ_HANDLED;
 }
 
-static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
-       struct net_device *dev = (struct net_device *) dev_id;
-       struct gfar_private *priv = netdev_priv(dev);
-
-       /* Clear the interrupt */
-       mii_clear_phy_interrupt(priv->mii_info);
-
-       /* Disable PHY interrupts */
-       mii_configure_phy_interrupt(priv->mii_info,
-                       MII_INTERRUPT_DISABLED);
-
-       /* Schedule the phy change */
-       schedule_work(&priv->tq);
-
-       return IRQ_HANDLED;
-}
-
-/* Scheduled by the phy_interrupt/timer to handle PHY changes */
-static void gfar_phy_change(void *data)
-{
-       struct net_device *dev = (struct net_device *) data;
-       struct gfar_private *priv = netdev_priv(dev);
-       int result = 0;
-
-       /* Delay to give the PHY a chance to change the
-        * register state */
-       msleep(1);
-
-       /* Update the link, speed, duplex */
-       result = priv->mii_info->phyinfo->read_status(priv->mii_info);
-
-       /* Adjust the known status as long as the link
-        * isn't still coming up */
-       if((0 == result) || (priv->mii_info->link == 0))
-               adjust_link(dev);
-
-       /* Reenable interrupts, if needed */
-       if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR)
-               mii_configure_phy_interrupt(priv->mii_info,
-                               MII_INTERRUPT_ENABLED);
-}
-
-/* Called every so often on systems that don't interrupt
- * the core for PHY changes */
-static void gfar_phy_timer(unsigned long data)
-{
-       struct net_device *dev = (struct net_device *) data;
-       struct gfar_private *priv = netdev_priv(dev);
-
-       schedule_work(&priv->tq);
-
-       mod_timer(&priv->phy_info_timer, jiffies +
-                       GFAR_PHY_CHANGE_TIME * HZ);
-}
-
-/* Keep trying aneg for some time
- * If, after GFAR_AN_TIMEOUT seconds, it has not
- * finished, we switch to forced.
- * Either way, once the process has completed, we either
- * request the interrupt, or switch the timer over to
- * using gfar_phy_timer to check status */
-static void gfar_phy_startup_timer(unsigned long data)
-{
-       int result;
-       static int secondary = GFAR_AN_TIMEOUT;
-       struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data;
-       struct gfar_private *priv = netdev_priv(mii_info->dev);
-
-       /* Configure the Auto-negotiation */
-       result = mii_info->phyinfo->config_aneg(mii_info);
-
-       /* If autonegotiation failed to start, and
-        * we haven't timed out, reset the timer, and return */
-       if (result && secondary--) {
-               mod_timer(&priv->phy_info_timer, jiffies + HZ);
-               return;
-       } else if (result) {
-               /* Couldn't start autonegotiation.
-                * Try switching to forced */
-               mii_info->autoneg = 0;
-               result = mii_info->phyinfo->config_aneg(mii_info);
-
-               /* Forcing failed!  Give up */
-               if(result) {
-                       if (netif_msg_link(priv))
-                               printk(KERN_ERR "%s: Forcing failed!\n",
-                                               mii_info->dev->name);
-                       return;
-               }
-       }
-
-       /* Kill the timer so it can be restarted */
-       del_timer_sync(&priv->phy_info_timer);
-
-       /* Grab the PHY interrupt, if necessary/possible */
-       if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
-               if (request_irq(priv->einfo->interruptPHY,
-                                       phy_interrupt,
-                                       SA_SHIRQ,
-                                       "phy_interrupt",
-                                       mii_info->dev) < 0) {
-                       if (netif_msg_intr(priv))
-                               printk(KERN_ERR "%s: Can't get IRQ %d (PHY)\n",
-                                               mii_info->dev->name,
-                                       priv->einfo->interruptPHY);
-               } else {
-                       mii_configure_phy_interrupt(priv->mii_info,
-                                       MII_INTERRUPT_ENABLED);
-                       return;
-               }
-       }
-
-       /* Start the timer again, this time in order to
-        * handle a change in status */
-       init_timer(&priv->phy_info_timer);
-       priv->phy_info_timer.function = &gfar_phy_timer;
-       priv->phy_info_timer.data = (unsigned long) mii_info->dev;
-       mod_timer(&priv->phy_info_timer, jiffies +
-                       GFAR_PHY_CHANGE_TIME * HZ);
-}
-
 /* Called every time the controller might need to be made
  * aware of new link state.  The PHY code conveys this
- * information through variables in the priv structure, and this
+ * information through variables in the phydev structure, and this
  * function converts those variables into the appropriate
  * register values, and can bring down the device if needed.
  */
@@ -1850,84 +1615,68 @@ static void adjust_link(struct net_device *dev)
 {
        struct gfar_private *priv = netdev_priv(dev);
        struct gfar *regs = priv->regs;
-       u32 tempval;
-       struct gfar_mii_info *mii_info = priv->mii_info;
+       unsigned long flags;
+       struct phy_device *phydev = priv->phydev;
+       int new_state = 0;
+
+       spin_lock_irqsave(&priv->lock, flags);
+       if (phydev->link) {
+               u32 tempval = gfar_read(&regs->maccfg2);
 
-       if (mii_info->link) {
                /* Now we make sure that we can be in full duplex mode.
                 * If not, we operate in half-duplex mode. */
-               if (mii_info->duplex != priv->oldduplex) {
-                       if (!(mii_info->duplex)) {
-                               tempval = gfar_read(&regs->maccfg2);
+               if (phydev->duplex != priv->oldduplex) {
+                       new_state = 1;
+                       if (!(phydev->duplex))
                                tempval &= ~(MACCFG2_FULL_DUPLEX);
-                               gfar_write(&regs->maccfg2, tempval);
-
-                               if (netif_msg_link(priv))
-                                       printk(KERN_INFO "%s: Half Duplex\n",
-                                                       dev->name);
-                       } else {
-                               tempval = gfar_read(&regs->maccfg2);
+                       else
                                tempval |= MACCFG2_FULL_DUPLEX;
-                               gfar_write(&regs->maccfg2, tempval);
 
-                               if (netif_msg_link(priv))
-                                       printk(KERN_INFO "%s: Full Duplex\n",
-                                                       dev->name);
-                       }
-
-                       priv->oldduplex = mii_info->duplex;
+                       priv->oldduplex = phydev->duplex;
                }
 
-               if (mii_info->speed != priv->oldspeed) {
-                       switch (mii_info->speed) {
+               if (phydev->speed != priv->oldspeed) {
+                       new_state = 1;
+                       switch (phydev->speed) {
                        case 1000:
-                               tempval = gfar_read(&regs->maccfg2);
                                tempval =
                                    ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII);
-                               gfar_write(&regs->maccfg2, tempval);
                                break;
                        case 100:
                        case 10:
-                               tempval = gfar_read(&regs->maccfg2);
                                tempval =
                                    ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII);
-                               gfar_write(&regs->maccfg2, tempval);
                                break;
                        default:
                                if (netif_msg_link(priv))
                                        printk(KERN_WARNING
-                                                       "%s: Ack!  Speed (%d) is not 10/100/1000!\n",
-                                                       dev->name, mii_info->speed);
+                                               "%s: Ack!  Speed (%d) is not 10/100/1000!\n",
+                                               dev->name, phydev->speed);
                                break;
                        }
 
-                       if (netif_msg_link(priv))
-                               printk(KERN_INFO "%s: Speed %dBT\n", dev->name,
-                                               mii_info->speed);
-
-                       priv->oldspeed = mii_info->speed;
+                       priv->oldspeed = phydev->speed;
                }
 
+               gfar_write(&regs->maccfg2, tempval);
+
                if (!priv->oldlink) {
-                       if (netif_msg_link(priv))
-                               printk(KERN_INFO "%s: Link is up\n", dev->name);
+                       new_state = 1;
                        priv->oldlink = 1;
-                       netif_carrier_on(dev);
                        netif_schedule(dev);
                }
-       } else {
-               if (priv->oldlink) {
-                       if (netif_msg_link(priv))
-                               printk(KERN_INFO "%s: Link is down\n",
-                                               dev->name);
-                       priv->oldlink = 0;
-                       priv->oldspeed = 0;
-                       priv->oldduplex = -1;
-                       netif_carrier_off(dev);
-               }
+       } else if (priv->oldlink) {
+               new_state = 1;
+               priv->oldlink = 0;
+               priv->oldspeed = 0;
+               priv->oldduplex = -1;
        }
-}
 
+       if (new_state && netif_msg_link(priv))
+               phy_print_status(phydev);
+
+       spin_unlock_irqrestore(&priv->lock, flags);
+}
 
 /* Update the hash table based on the current list of multicast
  * addresses we subscribe to.  Also, change the promiscuity of
@@ -2122,12 +1871,23 @@ static struct device_driver gfar_driver = {
 
 static int __init gfar_init(void)
 {
-       return driver_register(&gfar_driver);
+       int err = gfar_mdio_init();
+
+       if (err)
+               return err;
+
+       err = driver_register(&gfar_driver);
+
+       if (err)
+               gfar_mdio_exit();
+       
+       return err;
 }
 
 static void __exit gfar_exit(void)
 {
        driver_unregister(&gfar_driver);
+       gfar_mdio_exit();
 }
 
 module_init(gfar_init);
index 28af087d9fbba24d0005fd66c34f765005565610..c77ca6c0d04a6d651c0e3d37ca749146b5e9bc5c 100644 (file)
@@ -17,7 +17,6 @@
  *
  *  Still left to do:
  *      -Add support for module parameters
- *     -Add support for ethtool -s
  *     -Add patch for ethtool phys id
  */
 #ifndef __GIANFAR_H
@@ -37,7 +36,8 @@
 #include <linux/skbuff.h>
 #include <linux/spinlock.h>
 #include <linux/mm.h>
-#include <linux/fsl_devices.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -48,7 +48,8 @@
 #include <linux/workqueue.h>
 #include <linux/ethtool.h>
 #include <linux/netdevice.h>
-#include "gianfar_phy.h"
+#include <linux/fsl_devices.h>
+#include "gianfar_mii.h"
 
 /* The maximum number of packets to be handled in one call of gfar_poll */
 #define GFAR_DEV_WEIGHT 64
@@ -73,7 +74,7 @@
 #define PHY_INIT_TIMEOUT 100000
 #define GFAR_PHY_CHANGE_TIME 2
 
-#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.1, "
+#define DEVICE_NAME "%s: Gianfar Ethernet Controller Version 1.2, "
 #define DRV_NAME "gfar-enet"
 extern const char gfar_driver_name[];
 extern const char gfar_driver_version[];
@@ -578,12 +579,7 @@ struct gfar {
        u32     hafdup;         /* 0x.50c - Half Duplex Register */
        u32     maxfrm;         /* 0x.510 - Maximum Frame Length Register */
        u8      res18[12];
-       u32     miimcfg;        /* 0x.520 - MII Management Configuration Register */
-       u32     miimcom;        /* 0x.524 - MII Management Command Register */
-       u32     miimadd;        /* 0x.528 - MII Management Address Register */
-       u32     miimcon;        /* 0x.52c - MII Management Control Register */
-       u32     miimstat;       /* 0x.530 - MII Management Status Register */
-       u32     miimind;        /* 0x.534 - MII Management Indicator Register */
+       u8      gfar_mii_regs[24];      /* See gianfar_phy.h */
        u8      res19[4];
        u32     ifstat;         /* 0x.53c - Interface Status Register */
        u32     macstnaddr1;    /* 0x.540 - Station Address Part 1 Register */
@@ -688,9 +684,6 @@ struct gfar_private {
        struct gfar *regs;      /* Pointer to the GFAR memory mapped Registers */
        u32 *hash_regs[16];
        int hash_width;
-       struct gfar *phyregs;
-       struct work_struct tq;
-       struct timer_list phy_info_timer;
        struct net_device_stats stats; /* linux network statistics */
        struct gfar_extra_stats extra_stats;
        spinlock_t lock;
@@ -710,7 +703,8 @@ struct gfar_private {
        unsigned int interruptError;
        struct gianfar_platform_data *einfo;
 
-       struct gfar_mii_info *mii_info;
+       struct phy_device *phydev;
+       struct mii_bus *mii_bus;
        int oldspeed;
        int oldduplex;
        int oldlink;
@@ -732,4 +726,12 @@ extern inline void gfar_write(volatile unsigned *addr, u32 val)
 
 extern struct ethtool_ops *gfar_op_array[];
 
+extern irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs);
+extern int startup_gfar(struct net_device *dev);
+extern void stop_gfar(struct net_device *dev);
+extern void gfar_halt(struct net_device *dev);
+extern void gfar_phy_test(struct mii_bus *bus, struct phy_device *phydev,
+               int enable, u32 regnum, u32 read);
+void gfar_setup_stashing(struct net_device *dev);
+
 #endif /* __GIANFAR_H */
index a451de629197b13e1204f59b2707fef1d425e91d..68e3578e76133b8783b5dcfa1db03367c5e0d9ac 100644 (file)
 #include <asm/types.h>
 #include <asm/uaccess.h>
 #include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
 
 #include "gianfar.h"
 
 #define is_power_of_2(x)        ((x) != 0 && (((x) & ((x) - 1)) == 0))
 
-extern int startup_gfar(struct net_device *dev);
-extern void stop_gfar(struct net_device *dev);
-extern void gfar_halt(struct net_device *dev);
 extern void gfar_start(struct net_device *dev);
 extern int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
 
+#define GFAR_MAX_COAL_USECS 0xffff
+#define GFAR_MAX_COAL_FRAMES 0xff
 static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy,
                     u64 * buf);
 static void gfar_gstrings(struct net_device *dev, u32 stringset, u8 * buf);
@@ -182,38 +183,32 @@ static void gfar_gdrvinfo(struct net_device *dev, struct
        drvinfo->eedump_len = 0;
 }
 
+
+static int gfar_ssettings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+       struct gfar_private *priv = netdev_priv(dev);
+       struct phy_device *phydev = priv->phydev;
+
+       if (NULL == phydev)
+               return -ENODEV;
+
+       return phy_ethtool_sset(phydev, cmd);
+}
+
+
 /* Return the current settings in the ethtool_cmd structure */
 static int gfar_gsettings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
        struct gfar_private *priv = netdev_priv(dev);
-       uint gigabit_support = 
-               priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
-                       SUPPORTED_1000baseT_Full : 0;
-       uint gigabit_advert = 
-               priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
-                       ADVERTISED_1000baseT_Full: 0;
-
-       cmd->supported = (SUPPORTED_10baseT_Half
-                         | SUPPORTED_100baseT_Half
-                         | SUPPORTED_100baseT_Full
-                         | gigabit_support | SUPPORTED_Autoneg);
-
-       /* For now, we always advertise everything */
-       cmd->advertising = (ADVERTISED_10baseT_Half
-                           | ADVERTISED_100baseT_Half
-                           | ADVERTISED_100baseT_Full
-                           | gigabit_advert | ADVERTISED_Autoneg);
-
-       cmd->speed = priv->mii_info->speed;
-       cmd->duplex = priv->mii_info->duplex;
-       cmd->port = PORT_MII;
-       cmd->phy_address = priv->mii_info->mii_id;
-       cmd->transceiver = XCVR_EXTERNAL;
-       cmd->autoneg = AUTONEG_ENABLE;
+       struct phy_device *phydev = priv->phydev;
+
+       if (NULL == phydev)
+               return -ENODEV;
+       
        cmd->maxtxpkt = priv->txcount;
        cmd->maxrxpkt = priv->rxcount;
 
-       return 0;
+       return phy_ethtool_gset(phydev, cmd);
 }
 
 /* Return the length of the register structure */
@@ -241,14 +236,14 @@ static unsigned int gfar_usecs2ticks(struct gfar_private *priv, unsigned int use
        unsigned int count;
 
        /* The timer is different, depending on the interface speed */
-       switch (priv->mii_info->speed) {
-       case 1000:
+       switch (priv->phydev->speed) {
+       case SPEED_1000:
                count = GFAR_GBIT_TIME;
                break;
-       case 100:
+       case SPEED_100:
                count = GFAR_100_TIME;
                break;
-       case 10:
+       case SPEED_10:
        default:
                count = GFAR_10_TIME;
                break;
@@ -265,14 +260,14 @@ static unsigned int gfar_ticks2usecs(struct gfar_private *priv, unsigned int tic
        unsigned int count;
 
        /* The timer is different, depending on the interface speed */
-       switch (priv->mii_info->speed) {
-       case 1000:
+       switch (priv->phydev->speed) {
+       case SPEED_1000:
                count = GFAR_GBIT_TIME;
                break;
-       case 100:
+       case SPEED_100:
                count = GFAR_100_TIME;
                break;
-       case 10:
+       case SPEED_10:
        default:
                count = GFAR_10_TIME;
                break;
@@ -292,6 +287,9 @@ static int gfar_gcoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
        if (!(priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE))
                return -EOPNOTSUPP;
 
+       if (NULL == priv->phydev)
+               return -ENODEV;
+
        cvals->rx_coalesce_usecs = gfar_ticks2usecs(priv, priv->rxtime);
        cvals->rx_max_coalesced_frames = priv->rxcount;
 
@@ -348,6 +346,22 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
        else
                priv->rxcoalescing = 1;
 
+       if (NULL == priv->phydev)
+               return -ENODEV;
+
+       /* Check the bounds of the values */
+       if (cvals->rx_coalesce_usecs > GFAR_MAX_COAL_USECS) {
+               pr_info("Coalescing is limited to %d microseconds\n",
+                               GFAR_MAX_COAL_USECS);
+               return -EINVAL;
+       }
+
+       if (cvals->rx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) {
+               pr_info("Coalescing is limited to %d frames\n",
+                               GFAR_MAX_COAL_FRAMES);
+               return -EINVAL;
+       }
+
        priv->rxtime = gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs);
        priv->rxcount = cvals->rx_max_coalesced_frames;
 
@@ -358,6 +372,19 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
        else
                priv->txcoalescing = 1;
 
+       /* Check the bounds of the values */
+       if (cvals->tx_coalesce_usecs > GFAR_MAX_COAL_USECS) {
+               pr_info("Coalescing is limited to %d microseconds\n",
+                               GFAR_MAX_COAL_USECS);
+               return -EINVAL;
+       }
+
+       if (cvals->tx_max_coalesced_frames > GFAR_MAX_COAL_FRAMES) {
+               pr_info("Coalescing is limited to %d frames\n",
+                               GFAR_MAX_COAL_FRAMES);
+               return -EINVAL;
+       }
+
        priv->txtime = gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs);
        priv->txcount = cvals->tx_max_coalesced_frames;
 
@@ -536,6 +563,7 @@ static void gfar_set_msglevel(struct net_device *dev, uint32_t data)
 
 struct ethtool_ops gfar_ethtool_ops = {
        .get_settings = gfar_gsettings,
+       .set_settings = gfar_ssettings,
        .get_drvinfo = gfar_gdrvinfo,
        .get_regs_len = gfar_reglen,
        .get_regs = gfar_get_regs,
diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c
new file mode 100644 (file)
index 0000000..1eca1db
--- /dev/null
@@ -0,0 +1,219 @@
+/* 
+ * drivers/net/gianfar_mii.c
+ *
+ * Gianfar Ethernet Driver -- MIIM bus implementation
+ * Provides Bus interface for MIIM regs
+ *
+ * Author: Andy Fleming
+ * Maintainer: Kumar Gala (kumar.gala@freescale.com)
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <asm/ocp.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+#include "gianfar.h"
+#include "gianfar_mii.h"
+
+/* Write value to the PHY at mii_id at register regnum,
+ * on the bus, waiting until the write is done before returning.
+ * All PHY configuration is done through the TSEC1 MIIM regs */
+int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value)
+{
+       struct gfar_mii *regs = bus->priv;
+
+       /* Set the PHY address and the register address we want to write */
+       gfar_write(&regs->miimadd, (mii_id << 8) | regnum);
+
+       /* Write out the value we want */
+       gfar_write(&regs->miimcon, value);
+
+       /* Wait for the transaction to finish */
+       while (gfar_read(&regs->miimind) & MIIMIND_BUSY)
+               cpu_relax();
+
+       return 0;
+}
+
+/* Read the bus for PHY at addr mii_id, register regnum, and
+ * return the value.  Clears miimcom first.  All PHY
+ * configuration has to be done through the TSEC1 MIIM regs */
+int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+       struct gfar_mii *regs = bus->priv;
+       u16 value;
+
+       /* Set the PHY address and the register address we want to read */
+       gfar_write(&regs->miimadd, (mii_id << 8) | regnum);
+
+       /* Clear miimcom, and then initiate a read */
+       gfar_write(&regs->miimcom, 0);
+       gfar_write(&regs->miimcom, MII_READ_COMMAND);
+
+       /* Wait for the transaction to finish */
+       while (gfar_read(&regs->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY))
+               cpu_relax();
+
+       /* Grab the value of the register from miimstat */
+       value = gfar_read(&regs->miimstat);
+
+       return value;
+}
+
+
+/* Reset the MIIM registers, and wait for the bus to free */
+int gfar_mdio_reset(struct mii_bus *bus)
+{
+       struct gfar_mii *regs = bus->priv;
+       unsigned int timeout = PHY_INIT_TIMEOUT;
+
+       spin_lock_bh(&bus->mdio_lock);
+
+       /* Reset the management interface */
+       gfar_write(&regs->miimcfg, MIIMCFG_RESET);
+
+       /* Setup the MII Mgmt clock speed */
+       gfar_write(&regs->miimcfg, MIIMCFG_INIT_VALUE);
+
+       /* Wait until the bus is free */
+       while ((gfar_read(&regs->miimind) & MIIMIND_BUSY) &&
+                       timeout--)
+               cpu_relax();
+
+       spin_unlock_bh(&bus->mdio_lock);
+
+       if(timeout <= 0) {
+               printk(KERN_ERR "%s: The MII Bus is stuck!\n",
+                               bus->name);
+               return -EBUSY;
+       }
+
+       return 0;
+}
+
+
+int gfar_mdio_probe(struct device *dev)
+{
+       struct platform_device *pdev = to_platform_device(dev);
+       struct gianfar_mdio_data *pdata;
+       struct gfar_mii *regs;
+       struct mii_bus *new_bus;
+       int err = 0;
+
+       if (NULL == dev)
+               return -EINVAL;
+
+       new_bus = kmalloc(sizeof(struct mii_bus), GFP_KERNEL);
+
+       if (NULL == new_bus)
+               return -ENOMEM;
+
+       new_bus->name = "Gianfar MII Bus",
+       new_bus->read = &gfar_mdio_read,
+       new_bus->write = &gfar_mdio_write,
+       new_bus->reset = &gfar_mdio_reset,
+       new_bus->id = pdev->id;
+
+       pdata = (struct gianfar_mdio_data *)pdev->dev.platform_data;
+
+       if (NULL == pdata) {
+               printk(KERN_ERR "gfar mdio %d: Missing platform data!\n", pdev->id);
+               return -ENODEV;
+       }
+
+       /* Set the PHY base address */
+       regs = (struct gfar_mii *) ioremap(pdata->paddr, 
+                       sizeof (struct gfar_mii));
+
+       if (NULL == regs) {
+               err = -ENOMEM;
+               goto reg_map_fail;
+       }
+
+       new_bus->priv = regs;
+
+       new_bus->irq = pdata->irq;
+
+       new_bus->dev = dev;
+       dev_set_drvdata(dev, new_bus);
+
+       err = mdiobus_register(new_bus);
+
+       if (0 != err) {
+               printk (KERN_ERR "%s: Cannot register as MDIO bus\n", 
+                               new_bus->name);
+               goto bus_register_fail;
+       }
+
+       return 0;
+
+bus_register_fail:
+       iounmap((void *) regs);
+reg_map_fail:
+       kfree(new_bus);
+
+       return err;
+}
+
+
+int gfar_mdio_remove(struct device *dev)
+{
+       struct mii_bus *bus = dev_get_drvdata(dev);
+
+       mdiobus_unregister(bus);
+
+       dev_set_drvdata(dev, NULL);
+
+       iounmap((void *) (&bus->priv));
+       bus->priv = NULL;
+       kfree(bus);
+
+       return 0;
+}
+
+static struct device_driver gianfar_mdio_driver = {
+       .name = "fsl-gianfar_mdio",
+       .bus = &platform_bus_type,
+       .probe = gfar_mdio_probe,
+       .remove = gfar_mdio_remove,
+};
+
+int __init gfar_mdio_init(void)
+{
+       return driver_register(&gianfar_mdio_driver);
+}
+
+void __exit gfar_mdio_exit(void)
+{
+       driver_unregister(&gianfar_mdio_driver);
+}
diff --git a/drivers/net/gianfar_mii.h b/drivers/net/gianfar_mii.h
new file mode 100644 (file)
index 0000000..56e5665
--- /dev/null
@@ -0,0 +1,45 @@
+/* 
+ * drivers/net/gianfar_mii.h
+ *
+ * Gianfar Ethernet Driver -- MII Management Bus Implementation
+ * Driver for the MDIO bus controller in the Gianfar register space
+ *
+ * Author: Andy Fleming
+ * Maintainer: Kumar Gala (kumar.gala@freescale.com)
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __GIANFAR_MII_H
+#define __GIANFAR_MII_H
+
+#define MIIMIND_BUSY            0x00000001
+#define MIIMIND_NOTVALID        0x00000004
+
+#define MII_READ_COMMAND       0x00000001
+
+#define GFAR_SUPPORTED (SUPPORTED_10baseT_Half \
+               | SUPPORTED_100baseT_Half \
+               | SUPPORTED_100baseT_Full \
+               | SUPPORTED_Autoneg \
+               | SUPPORTED_MII)
+
+struct gfar_mii {
+       u32     miimcfg;        /* 0x.520 - MII Management Config Register */
+       u32     miimcom;        /* 0x.524 - MII Management Command Register */
+       u32     miimadd;        /* 0x.528 - MII Management Address Register */
+       u32     miimcon;        /* 0x.52c - MII Management Control Register */
+       u32     miimstat;       /* 0x.530 - MII Management Status Register */
+       u32     miimind;        /* 0x.534 - MII Management Indicator Register */
+};
+
+int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum);
+int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+int __init gfar_mdio_init(void);
+void __exit gfar_mdio_exit(void);
+#endif /* GIANFAR_PHY_H */
diff --git a/drivers/net/gianfar_phy.c b/drivers/net/gianfar_phy.c
deleted file mode 100644 (file)
index 7c965f2..0000000
+++ /dev/null
@@ -1,661 +0,0 @@
-/* 
- * drivers/net/gianfar_phy.c
- *
- * Gianfar Ethernet Driver -- PHY handling
- * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560
- * Based on 8260_io/fcc_enet.c
- *
- * Author: Andy Fleming
- * Maintainer: Kumar Gala (kumar.gala@freescale.com)
- *
- * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-#include <linux/config.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mm.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-#include <linux/module.h>
-#include <linux/version.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-
-#include "gianfar.h"
-#include "gianfar_phy.h"
-
-static void config_genmii_advert(struct gfar_mii_info *mii_info);
-static void genmii_setup_forced(struct gfar_mii_info *mii_info);
-static void genmii_restart_aneg(struct gfar_mii_info *mii_info);
-static int gbit_config_aneg(struct gfar_mii_info *mii_info);
-static int genmii_config_aneg(struct gfar_mii_info *mii_info);
-static int genmii_update_link(struct gfar_mii_info *mii_info);
-static int genmii_read_status(struct gfar_mii_info *mii_info);
-u16 phy_read(struct gfar_mii_info *mii_info, u16 regnum);
-void phy_write(struct gfar_mii_info *mii_info, u16 regnum, u16 val);
-
-/* Write value to the PHY for this device to the register at regnum, */
-/* waiting until the write is done before it returns.  All PHY */
-/* configuration has to be done through the TSEC1 MIIM regs */
-void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value)
-{
-       struct gfar_private *priv = netdev_priv(dev);
-       struct gfar *regbase = priv->phyregs;
-
-       /* Set the PHY address and the register address we want to write */
-       gfar_write(&regbase->miimadd, (mii_id << 8) | regnum);
-
-       /* Write out the value we want */
-       gfar_write(&regbase->miimcon, value);
-
-       /* Wait for the transaction to finish */
-       while (gfar_read(&regbase->miimind) & MIIMIND_BUSY)
-               cpu_relax();
-}
-
-/* Reads from register regnum in the PHY for device dev, */
-/* returning the value.  Clears miimcom first.  All PHY */
-/* configuration has to be done through the TSEC1 MIIM regs */
-int read_phy_reg(struct net_device *dev, int mii_id, int regnum)
-{
-       struct gfar_private *priv = netdev_priv(dev);
-       struct gfar *regbase = priv->phyregs;
-       u16 value;
-
-       /* Set the PHY address and the register address we want to read */
-       gfar_write(&regbase->miimadd, (mii_id << 8) | regnum);
-
-       /* Clear miimcom, and then initiate a read */
-       gfar_write(&regbase->miimcom, 0);
-       gfar_write(&regbase->miimcom, MII_READ_COMMAND);
-
-       /* Wait for the transaction to finish */
-       while (gfar_read(&regbase->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY))
-               cpu_relax();
-
-       /* Grab the value of the register from miimstat */
-       value = gfar_read(&regbase->miimstat);
-
-       return value;
-}
-
-void mii_clear_phy_interrupt(struct gfar_mii_info *mii_info)
-{
-       if(mii_info->phyinfo->ack_interrupt)
-               mii_info->phyinfo->ack_interrupt(mii_info);
-}
-
-
-void mii_configure_phy_interrupt(struct gfar_mii_info *mii_info, u32 interrupts)
-{
-       mii_info->interrupts = interrupts;
-       if(mii_info->phyinfo->config_intr)
-               mii_info->phyinfo->config_intr(mii_info);
-}
-
-
-/* Writes MII_ADVERTISE with the appropriate values, after
- * sanitizing advertise to make sure only supported features
- * are advertised 
- */
-static void config_genmii_advert(struct gfar_mii_info *mii_info)
-{
-       u32 advertise;
-       u16 adv;
-
-       /* Only allow advertising what this PHY supports */
-       mii_info->advertising &= mii_info->phyinfo->features;
-       advertise = mii_info->advertising;
-
-       /* Setup standard advertisement */
-       adv = phy_read(mii_info, MII_ADVERTISE);
-       adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
-       if (advertise & ADVERTISED_10baseT_Half)
-               adv |= ADVERTISE_10HALF;
-       if (advertise & ADVERTISED_10baseT_Full)
-               adv |= ADVERTISE_10FULL;
-       if (advertise & ADVERTISED_100baseT_Half)
-               adv |= ADVERTISE_100HALF;
-       if (advertise & ADVERTISED_100baseT_Full)
-               adv |= ADVERTISE_100FULL;
-       phy_write(mii_info, MII_ADVERTISE, adv);
-}
-
-static void genmii_setup_forced(struct gfar_mii_info *mii_info)
-{
-       u16 ctrl;
-       u32 features = mii_info->phyinfo->features;
-       
-       ctrl = phy_read(mii_info, MII_BMCR);
-
-       ctrl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPEED1000|BMCR_ANENABLE);
-       ctrl |= BMCR_RESET;
-
-       switch(mii_info->speed) {
-               case SPEED_1000:
-                       if(features & (SUPPORTED_1000baseT_Half
-                                               | SUPPORTED_1000baseT_Full)) {
-                               ctrl |= BMCR_SPEED1000;
-                               break;
-                       }
-                       mii_info->speed = SPEED_100;
-               case SPEED_100:
-                       if (features & (SUPPORTED_100baseT_Half
-                                               | SUPPORTED_100baseT_Full)) {
-                               ctrl |= BMCR_SPEED100;
-                               break;
-                       }
-                       mii_info->speed = SPEED_10;
-               case SPEED_10:
-                       if (features & (SUPPORTED_10baseT_Half
-                                               | SUPPORTED_10baseT_Full))
-                               break;
-               default: /* Unsupported speed! */
-                       printk(KERN_ERR "%s: Bad speed!\n", 
-                                       mii_info->dev->name);
-                       break;
-       }
-
-       phy_write(mii_info, MII_BMCR, ctrl);
-}
-
-
-/* Enable and Restart Autonegotiation */
-static void genmii_restart_aneg(struct gfar_mii_info *mii_info)
-{
-       u16 ctl;
-
-       ctl = phy_read(mii_info, MII_BMCR);
-       ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
-       phy_write(mii_info, MII_BMCR, ctl);
-}
-
-
-static int gbit_config_aneg(struct gfar_mii_info *mii_info)
-{
-       u16 adv;
-       u32 advertise;
-
-       if(mii_info->autoneg) {
-               /* Configure the ADVERTISE register */
-               config_genmii_advert(mii_info);
-               advertise = mii_info->advertising;
-
-               adv = phy_read(mii_info, MII_1000BASETCONTROL);
-               adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP |
-                               MII_1000BASETCONTROL_HALFDUPLEXCAP);
-               if (advertise & SUPPORTED_1000baseT_Half)
-                       adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
-               if (advertise & SUPPORTED_1000baseT_Full)
-                       adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
-               phy_write(mii_info, MII_1000BASETCONTROL, adv);
-
-               /* Start/Restart aneg */
-               genmii_restart_aneg(mii_info);
-       } else
-               genmii_setup_forced(mii_info);
-
-       return 0;
-}
-
-static int marvell_config_aneg(struct gfar_mii_info *mii_info)
-{
-       /* The Marvell PHY has an errata which requires
-        * that certain registers get written in order
-        * to restart autonegotiation */
-       phy_write(mii_info, MII_BMCR, BMCR_RESET);
-
-       phy_write(mii_info, 0x1d, 0x1f);
-       phy_write(mii_info, 0x1e, 0x200c);
-       phy_write(mii_info, 0x1d, 0x5);
-       phy_write(mii_info, 0x1e, 0);
-       phy_write(mii_info, 0x1e, 0x100);
-
-       gbit_config_aneg(mii_info);
-
-       return 0;
-}
-static int genmii_config_aneg(struct gfar_mii_info *mii_info)
-{
-       if (mii_info->autoneg) {
-               config_genmii_advert(mii_info);
-               genmii_restart_aneg(mii_info);
-       } else
-               genmii_setup_forced(mii_info);
-
-       return 0;
-}
-
-
-static int genmii_update_link(struct gfar_mii_info *mii_info)
-{
-       u16 status;
-
-       /* Do a fake read */
-       phy_read(mii_info, MII_BMSR);
-
-       /* Read link and autonegotiation status */
-       status = phy_read(mii_info, MII_BMSR);
-       if ((status & BMSR_LSTATUS) == 0)
-               mii_info->link = 0;
-       else
-               mii_info->link = 1;
-
-       /* If we are autonegotiating, and not done, 
-        * return an error */
-       if (mii_info->autoneg && !(status & BMSR_ANEGCOMPLETE))
-               return -EAGAIN;
-
-       return 0;
-}
-
-static int genmii_read_status(struct gfar_mii_info *mii_info)
-{
-       u16 status;
-       int err;
-
-       /* Update the link, but return if there
-        * was an error */
-       err = genmii_update_link(mii_info);
-       if (err)
-               return err;
-
-       if (mii_info->autoneg) {
-               status = phy_read(mii_info, MII_LPA);
-
-               if (status & (LPA_10FULL | LPA_100FULL))
-                       mii_info->duplex = DUPLEX_FULL;
-               else
-                       mii_info->duplex = DUPLEX_HALF;
-               if (status & (LPA_100FULL | LPA_100HALF))
-                       mii_info->speed = SPEED_100;
-               else
-                       mii_info->speed = SPEED_10;
-               mii_info->pause = 0;
-       }
-       /* On non-aneg, we assume what we put in BMCR is the speed,
-        * though magic-aneg shouldn't prevent this case from occurring
-        */
-
-       return 0;
-}
-static int marvell_read_status(struct gfar_mii_info *mii_info)
-{
-       u16 status;
-       int err;
-
-       /* Update the link, but return if there
-        * was an error */
-       err = genmii_update_link(mii_info);
-       if (err)
-               return err;
-
-       /* If the link is up, read the speed and duplex */
-       /* If we aren't autonegotiating, assume speeds 
-        * are as set */
-       if (mii_info->autoneg && mii_info->link) {
-               int speed;
-               status = phy_read(mii_info, MII_M1011_PHY_SPEC_STATUS);
-
-#if 0
-               /* If speed and duplex aren't resolved,
-                * return an error.  Isn't this handled
-                * by checking aneg?
-                */
-               if ((status & MII_M1011_PHY_SPEC_STATUS_RESOLVED) == 0)
-                       return -EAGAIN;
-#endif
-
-               /* Get the duplexity */
-               if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX)
-                       mii_info->duplex = DUPLEX_FULL;
-               else
-                       mii_info->duplex = DUPLEX_HALF;
-
-               /* Get the speed */
-               speed = status & MII_M1011_PHY_SPEC_STATUS_SPD_MASK;
-               switch(speed) {
-                       case MII_M1011_PHY_SPEC_STATUS_1000:
-                               mii_info->speed = SPEED_1000;
-                               break;
-                       case MII_M1011_PHY_SPEC_STATUS_100:
-                               mii_info->speed = SPEED_100;
-                               break;
-                       default:
-                               mii_info->speed = SPEED_10;
-                               break;
-               }
-               mii_info->pause = 0;
-       }
-
-       return 0;
-}
-
-
-static int cis820x_read_status(struct gfar_mii_info *mii_info)
-{
-       u16 status;
-       int err;
-
-       /* Update the link, but return if there
-        * was an error */
-       err = genmii_update_link(mii_info);
-       if (err)
-               return err;
-
-       /* If the link is up, read the speed and duplex */
-       /* If we aren't autonegotiating, assume speeds 
-        * are as set */
-       if (mii_info->autoneg && mii_info->link) {
-               int speed;
-
-               status = phy_read(mii_info, MII_CIS8201_AUX_CONSTAT);
-               if (status & MII_CIS8201_AUXCONSTAT_DUPLEX)
-                       mii_info->duplex = DUPLEX_FULL;
-               else
-                       mii_info->duplex = DUPLEX_HALF;
-
-               speed = status & MII_CIS8201_AUXCONSTAT_SPEED;
-
-               switch (speed) {
-               case MII_CIS8201_AUXCONSTAT_GBIT:
-                       mii_info->speed = SPEED_1000;
-                       break;
-               case MII_CIS8201_AUXCONSTAT_100:
-                       mii_info->speed = SPEED_100;
-                       break;
-               default:
-                       mii_info->speed = SPEED_10;
-                       break;
-               }
-       }
-
-       return 0;
-}
-
-static int marvell_ack_interrupt(struct gfar_mii_info *mii_info)
-{
-       /* Clear the interrupts by reading the reg */
-       phy_read(mii_info, MII_M1011_IEVENT);
-
-       return 0;
-}
-
-static int marvell_config_intr(struct gfar_mii_info *mii_info)
-{
-       if(mii_info->interrupts == MII_INTERRUPT_ENABLED)
-               phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
-       else
-               phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
-
-       return 0;
-}
-
-static int cis820x_init(struct gfar_mii_info *mii_info)
-{
-       phy_write(mii_info, MII_CIS8201_AUX_CONSTAT, 
-                       MII_CIS8201_AUXCONSTAT_INIT);
-       phy_write(mii_info, MII_CIS8201_EXT_CON1,
-                       MII_CIS8201_EXTCON1_INIT);
-
-       return 0;
-}
-
-static int cis820x_ack_interrupt(struct gfar_mii_info *mii_info)
-{
-       phy_read(mii_info, MII_CIS8201_ISTAT);
-
-       return 0;
-}
-
-static int cis820x_config_intr(struct gfar_mii_info *mii_info)
-{
-       if(mii_info->interrupts == MII_INTERRUPT_ENABLED)
-               phy_write(mii_info, MII_CIS8201_IMASK, MII_CIS8201_IMASK_MASK);
-       else
-               phy_write(mii_info, MII_CIS8201_IMASK, 0);
-
-       return 0;
-}
-
-#define DM9161_DELAY 10
-
-static int dm9161_read_status(struct gfar_mii_info *mii_info)
-{
-       u16 status;
-       int err;
-
-       /* Update the link, but return if there
-        * was an error */
-       err = genmii_update_link(mii_info);
-       if (err)
-               return err;
-
-       /* If the link is up, read the speed and duplex */
-       /* If we aren't autonegotiating, assume speeds 
-        * are as set */
-       if (mii_info->autoneg && mii_info->link) {
-               status = phy_read(mii_info, MII_DM9161_SCSR);
-               if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_100H))
-                       mii_info->speed = SPEED_100;
-               else
-                       mii_info->speed = SPEED_10;
-
-               if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_10F))
-                       mii_info->duplex = DUPLEX_FULL;
-               else
-                       mii_info->duplex = DUPLEX_HALF;
-       }
-
-       return 0;
-}
-
-
-static int dm9161_config_aneg(struct gfar_mii_info *mii_info)
-{
-       struct dm9161_private *priv = mii_info->priv;
-
-       if(0 == priv->resetdone)
-               return -EAGAIN;
-
-       return 0;
-}
-
-static void dm9161_timer(unsigned long data)
-{
-       struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data;
-       struct dm9161_private *priv = mii_info->priv;
-       u16 status = phy_read(mii_info, MII_BMSR);
-
-       if (status & BMSR_ANEGCOMPLETE) {
-               priv->resetdone = 1;
-       } else
-               mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ);
-}
-
-static int dm9161_init(struct gfar_mii_info *mii_info)
-{
-       struct dm9161_private *priv;
-
-       /* Allocate the private data structure */
-       priv = kmalloc(sizeof(struct dm9161_private), GFP_KERNEL);
-
-       if (NULL == priv)
-               return -ENOMEM;
-
-       mii_info->priv = priv;
-
-       /* Reset is not done yet */
-       priv->resetdone = 0;
-
-       /* Isolate the PHY */
-       phy_write(mii_info, MII_BMCR, BMCR_ISOLATE);
-
-       /* Do not bypass the scrambler/descrambler */
-       phy_write(mii_info, MII_DM9161_SCR, MII_DM9161_SCR_INIT);
-
-       /* Clear 10BTCSR to default */
-       phy_write(mii_info, MII_DM9161_10BTCSR, MII_DM9161_10BTCSR_INIT);
-
-       /* Reconnect the PHY, and enable Autonegotiation */
-       phy_write(mii_info, MII_BMCR, BMCR_ANENABLE);
-
-       /* Start a timer for DM9161_DELAY seconds to wait
-        * for the PHY to be ready */
-       init_timer(&priv->timer);
-       priv->timer.function = &dm9161_timer;
-       priv->timer.data = (unsigned long) mii_info;
-       mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ);
-
-       return 0;
-}
-
-static void dm9161_close(struct gfar_mii_info *mii_info)
-{
-       struct dm9161_private *priv = mii_info->priv;
-
-       del_timer_sync(&priv->timer);
-       kfree(priv);
-}
-
-#if 0
-static int dm9161_ack_interrupt(struct gfar_mii_info *mii_info)
-{
-       phy_read(mii_info, MII_DM9161_INTR);
-
-       return 0;
-}
-#endif
-
-/* Cicada 820x */
-static struct phy_info phy_info_cis820x = {
-       0x000fc440,
-       "Cicada Cis8204",
-       0x000fffc0,
-       .features       = MII_GBIT_FEATURES,
-       .init           = &cis820x_init,
-       .config_aneg    = &gbit_config_aneg,
-       .read_status    = &cis820x_read_status,
-       .ack_interrupt  = &cis820x_ack_interrupt,
-       .config_intr    = &cis820x_config_intr,
-};
-
-static struct phy_info phy_info_dm9161 = {
-       .phy_id         = 0x0181b880,
-       .name           = "Davicom DM9161E",
-       .phy_id_mask    = 0x0ffffff0,
-       .init           = dm9161_init,
-       .config_aneg    = dm9161_config_aneg,
-       .read_status    = dm9161_read_status,
-       .close          = dm9161_close,
-};
-
-static struct phy_info phy_info_marvell = {
-       .phy_id         = 0x01410c00,
-       .phy_id_mask    = 0xffffff00,
-       .name           = "Marvell 88E1101/88E1111",
-       .features       = MII_GBIT_FEATURES,
-       .config_aneg    = &marvell_config_aneg,
-       .read_status    = &marvell_read_status,
-       .ack_interrupt  = &marvell_ack_interrupt,
-       .config_intr    = &marvell_config_intr,
-};
-
-static struct phy_info phy_info_genmii= {
-       .phy_id         = 0x00000000,
-       .phy_id_mask    = 0x00000000,
-       .name           = "Generic MII",
-       .features       = MII_BASIC_FEATURES,
-       .config_aneg    = genmii_config_aneg,
-       .read_status    = genmii_read_status,
-};
-
-static struct phy_info *phy_info[] = {
-       &phy_info_cis820x,
-       &phy_info_marvell,
-       &phy_info_dm9161,
-       &phy_info_genmii,
-       NULL
-};
-
-u16 phy_read(struct gfar_mii_info *mii_info, u16 regnum)
-{
-       u16 retval;
-       unsigned long flags;
-
-       spin_lock_irqsave(&mii_info->mdio_lock, flags);
-       retval = mii_info->mdio_read(mii_info->dev, mii_info->mii_id, regnum);
-       spin_unlock_irqrestore(&mii_info->mdio_lock, flags);
-
-       return retval;
-}
-
-void phy_write(struct gfar_mii_info *mii_info, u16 regnum, u16 val)
-{
-       unsigned long flags;
-
-       spin_lock_irqsave(&mii_info->mdio_lock, flags);
-       mii_info->mdio_write(mii_info->dev, 
-                       mii_info->mii_id, 
-                       regnum, val);
-       spin_unlock_irqrestore(&mii_info->mdio_lock, flags);
-}
-
-/* Use the PHY ID registers to determine what type of PHY is attached
- * to device dev.  return a struct phy_info structure describing that PHY
- */
-struct phy_info * get_phy_info(struct gfar_mii_info *mii_info)
-{
-       u16 phy_reg;
-       u32 phy_ID;
-       int i;
-       struct phy_info *theInfo = NULL;
-       struct net_device *dev = mii_info->dev;
-
-       /* Grab the bits from PHYIR1, and put them in the upper half */
-       phy_reg = phy_read(mii_info, MII_PHYSID1);
-       phy_ID = (phy_reg & 0xffff) << 16;
-
-       /* Grab the bits from PHYIR2, and put them in the lower half */
-       phy_reg = phy_read(mii_info, MII_PHYSID2);
-       phy_ID |= (phy_reg & 0xffff);
-
-       /* loop through all the known PHY types, and find one that */
-       /* matches the ID we read from the PHY. */
-       for (i = 0; phy_info[i]; i++)
-               if (phy_info[i]->phy_id == 
-                               (phy_ID & phy_info[i]->phy_id_mask)) {
-                       theInfo = phy_info[i];
-                       break;
-               }
-
-       /* This shouldn't happen, as we have generic PHY support */
-       if (theInfo == NULL) {
-               printk("%s: PHY id %x is not supported!\n", dev->name, phy_ID);
-               return NULL;
-       } else {
-               printk("%s: PHY is %s (%x)\n", dev->name, theInfo->name,
-                      phy_ID);
-       }
-
-       return theInfo;
-}
diff --git a/drivers/net/gianfar_phy.h b/drivers/net/gianfar_phy.h
deleted file mode 100644 (file)
index 1e9b3ab..0000000
+++ /dev/null
@@ -1,213 +0,0 @@
-/* 
- * drivers/net/gianfar_phy.h
- *
- * Gianfar Ethernet Driver -- PHY handling
- * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560
- * Based on 8260_io/fcc_enet.c
- *
- * Author: Andy Fleming
- * Maintainer: Kumar Gala (kumar.gala@freescale.com)
- *
- * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-#ifndef __GIANFAR_PHY_H
-#define __GIANFAR_PHY_H
-
-#define MII_end ((u32)-2)
-#define MII_read ((u32)-1)
-
-#define MIIMIND_BUSY            0x00000001
-#define MIIMIND_NOTVALID        0x00000004
-
-#define GFAR_AN_TIMEOUT         2000
-
-/* 1000BT control (Marvell & BCM54xx at least) */
-#define MII_1000BASETCONTROL                   0x09
-#define MII_1000BASETCONTROL_FULLDUPLEXCAP     0x0200
-#define MII_1000BASETCONTROL_HALFDUPLEXCAP     0x0100
-
-/* Cicada Extended Control Register 1 */
-#define MII_CIS8201_EXT_CON1           0x17
-#define MII_CIS8201_EXTCON1_INIT       0x0000
-
-/* Cicada Interrupt Mask Register */
-#define MII_CIS8201_IMASK              0x19
-#define MII_CIS8201_IMASK_IEN          0x8000
-#define MII_CIS8201_IMASK_SPEED        0x4000
-#define MII_CIS8201_IMASK_LINK         0x2000
-#define MII_CIS8201_IMASK_DUPLEX       0x1000
-#define MII_CIS8201_IMASK_MASK         0xf000
-
-/* Cicada Interrupt Status Register */
-#define MII_CIS8201_ISTAT              0x1a
-#define MII_CIS8201_ISTAT_STATUS       0x8000
-#define MII_CIS8201_ISTAT_SPEED        0x4000
-#define MII_CIS8201_ISTAT_LINK         0x2000
-#define MII_CIS8201_ISTAT_DUPLEX       0x1000
-
-/* Cicada Auxiliary Control/Status Register */
-#define MII_CIS8201_AUX_CONSTAT        0x1c
-#define MII_CIS8201_AUXCONSTAT_INIT    0x0004
-#define MII_CIS8201_AUXCONSTAT_DUPLEX  0x0020
-#define MII_CIS8201_AUXCONSTAT_SPEED   0x0018
-#define MII_CIS8201_AUXCONSTAT_GBIT    0x0010
-#define MII_CIS8201_AUXCONSTAT_100     0x0008
-                                                                                
-/* 88E1011 PHY Status Register */
-#define MII_M1011_PHY_SPEC_STATUS              0x11
-#define MII_M1011_PHY_SPEC_STATUS_1000         0x8000
-#define MII_M1011_PHY_SPEC_STATUS_100          0x4000
-#define MII_M1011_PHY_SPEC_STATUS_SPD_MASK     0xc000
-#define MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX   0x2000
-#define MII_M1011_PHY_SPEC_STATUS_RESOLVED     0x0800
-#define MII_M1011_PHY_SPEC_STATUS_LINK         0x0400
-
-#define MII_M1011_IEVENT               0x13
-#define MII_M1011_IEVENT_CLEAR         0x0000
-
-#define MII_M1011_IMASK                        0x12
-#define MII_M1011_IMASK_INIT           0x6400
-#define MII_M1011_IMASK_CLEAR          0x0000
-
-#define MII_DM9161_SCR         0x10
-#define MII_DM9161_SCR_INIT    0x0610
-
-/* DM9161 Specified Configuration and Status Register */
-#define MII_DM9161_SCSR        0x11
-#define MII_DM9161_SCSR_100F   0x8000
-#define MII_DM9161_SCSR_100H   0x4000
-#define MII_DM9161_SCSR_10F    0x2000
-#define MII_DM9161_SCSR_10H    0x1000
-
-/* DM9161 Interrupt Register */
-#define MII_DM9161_INTR        0x15
-#define MII_DM9161_INTR_PEND           0x8000
-#define MII_DM9161_INTR_DPLX_MASK      0x0800
-#define MII_DM9161_INTR_SPD_MASK       0x0400
-#define MII_DM9161_INTR_LINK_MASK      0x0200
-#define MII_DM9161_INTR_MASK           0x0100
-#define MII_DM9161_INTR_DPLX_CHANGE    0x0010
-#define MII_DM9161_INTR_SPD_CHANGE     0x0008
-#define MII_DM9161_INTR_LINK_CHANGE    0x0004
-#define MII_DM9161_INTR_INIT           0x0000
-#define MII_DM9161_INTR_STOP   \
-(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \
- | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK)
-
-/* DM9161 10BT Configuration/Status */
-#define MII_DM9161_10BTCSR     0x12
-#define MII_DM9161_10BTCSR_INIT        0x7800
-
-#define MII_BASIC_FEATURES     (SUPPORTED_10baseT_Half | \
-                                SUPPORTED_10baseT_Full | \
-                                SUPPORTED_100baseT_Half | \
-                                SUPPORTED_100baseT_Full | \
-                                SUPPORTED_Autoneg | \
-                                SUPPORTED_TP | \
-                                SUPPORTED_MII)
-
-#define MII_GBIT_FEATURES      (MII_BASIC_FEATURES | \
-                                SUPPORTED_1000baseT_Half | \
-                                SUPPORTED_1000baseT_Full)
-
-#define MII_READ_COMMAND       0x00000001
-
-#define MII_INTERRUPT_DISABLED 0x0
-#define MII_INTERRUPT_ENABLED 0x1
-/* Taken from mii_if_info and sungem_phy.h */
-struct gfar_mii_info {
-       /* Information about the PHY type */
-       /* And management functions */
-       struct phy_info *phyinfo;
-
-       /* forced speed & duplex (no autoneg)
-        * partner speed & duplex & pause (autoneg)
-        */
-       int speed;
-       int duplex;
-       int pause;
-
-       /* The most recently read link state */
-       int link;
-
-       /* Enabled Interrupts */
-       u32 interrupts;
-
-       u32 advertising;
-       int autoneg;
-       int mii_id;
-
-       /* private data pointer */
-       /* For use by PHYs to maintain extra state */
-       void *priv;
-
-       /* Provided by host chip */
-       struct net_device *dev;
-
-       /* A lock to ensure that only one thing can read/write
-        * the MDIO bus at a time */
-       spinlock_t mdio_lock;
-
-       /* Provided by ethernet driver */
-       int (*mdio_read) (struct net_device *dev, int mii_id, int reg);
-       void (*mdio_write) (struct net_device *dev, int mii_id, int reg, int val);
-};
-
-/* struct phy_info: a structure which defines attributes for a PHY
- *
- * id will contain a number which represents the PHY.  During
- * startup, the driver will poll the PHY to find out what its
- * UID--as defined by registers 2 and 3--is.  The 32-bit result
- * gotten from the PHY will be ANDed with phy_id_mask to
- * discard any bits which may change based on revision numbers
- * unimportant to functionality
- *
- * There are 6 commands which take a gfar_mii_info structure.
- * Each PHY must declare config_aneg, and read_status.
- */
-struct phy_info {
-       u32 phy_id;
-       char *name;
-       unsigned int phy_id_mask;
-       u32 features;
-
-       /* Called to initialize the PHY */
-       int (*init)(struct gfar_mii_info *mii_info);
-
-       /* Called to suspend the PHY for power */
-       int (*suspend)(struct gfar_mii_info *mii_info);
-
-       /* Reconfigures autonegotiation (or disables it) */
-       int (*config_aneg)(struct gfar_mii_info *mii_info);
-
-       /* Determines the negotiated speed and duplex */
-       int (*read_status)(struct gfar_mii_info *mii_info);
-
-       /* Clears any pending interrupts */
-       int (*ack_interrupt)(struct gfar_mii_info *mii_info);
-
-       /* Enables or disables interrupts */
-       int (*config_intr)(struct gfar_mii_info *mii_info);
-
-       /* Clears up any memory if needed */
-       void (*close)(struct gfar_mii_info *mii_info);
-};
-
-struct phy_info *get_phy_info(struct gfar_mii_info *mii_info);
-int read_phy_reg(struct net_device *dev, int mii_id, int regnum);
-void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value);
-void mii_clear_phy_interrupt(struct gfar_mii_info *mii_info);
-void mii_configure_phy_interrupt(struct gfar_mii_info *mii_info, u32 interrupts);
-
-struct dm9161_private {
-       struct timer_list timer;
-       int resetdone;
-};
-
-#endif /* GIANFAR_PHY_H */