i2c: i801: Fix I2C Block Read on 8-Series/C220 and later

Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.

However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.

So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index 08847e8b899872e2bc1bffd1d0936f63ee4f38d7..eb3627f35d12002776447982d493835fe36dc064 100644 (file)
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -146,6 +146,7 @@
 #define SMBHSTCFG_HST_EN       1
 #define SMBHSTCFG_SMB_SMI_EN   2
 #define SMBHSTCFG_I2C_EN       4
+#define SMBHSTCFG_SPD_WD       0x10
 
 /* TCO configuration bits for TCOCTL */
 #define TCOCTL_EN              0x0100
@@ -865,9 +866,16 @@ static s32 i801_access(struct i2c_adapter *adap, u16 addr,
                block = 1;
                break;
        case I2C_SMBUS_I2C_BLOCK_DATA:
-               /* NB: page 240 of ICH5 datasheet shows that the R/#W
-                * bit should be cleared here, even when reading */
-               outb_p((addr & 0x7f) << 1, SMBHSTADD(priv));
+               /*
+                * NB: page 240 of ICH5 datasheet shows that the R/#W
+                * bit should be cleared here, even when reading.
+                * However if SPD Write Disable is set (Lynx Point and later),
+                * the read will fail if we don't set the R/#W bit.
+                */
+               outb_p(((addr & 0x7f) << 1) |
+                      ((priv->original_hstcfg & SMBHSTCFG_SPD_WD) ?
+                       (read_write & 0x01) : 0),
+                      SMBHSTADD(priv));
                if (read_write == I2C_SMBUS_READ) {
                        /* NB: page 240 of ICH5 datasheet also shows
                         * that DATA1 is the cmd field when reading */
@@ -1573,6 +1581,8 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id)
                /* Disable SMBus interrupt feature if SMBus using SMI# */
                priv->features &= ~FEATURE_IRQ;
        }
+       if (temp & SMBHSTCFG_SPD_WD)
+               dev_info(&dev->dev, "SPD Write Disable is set\n");
 
        /* Clear special mode bits */
        if (priv->features & (FEATURE_SMBUS_PEC | FEATURE_BLOCK_BUFFER))