bnx2x_restart_autoneg(phy, params, 0);
DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n");
}
-static u8 bnx2x_link_settings_status(struct link_params *params,
- struct link_vars *vars,
- u32 gp_status,
- u8 ext_phy_link_up)
+static u8 bnx2x_link_settings_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
- u16 new_line_speed;
+ u16 new_line_speed , gp_status;
u8 rc = 0;
u32 ext_phy_type;
- vars->link_status = 0;
+ /* Read gp_status */
+ CL45_RD_OVER_CL22(bp, phy,
+ MDIO_REG_BANK_GP_STATUS,
+ MDIO_GP_STATUS_TOP_AN_STATUS1,
+ &gp_status);
+
if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
DP(NETIF_MSG_LINK, "phy link up gp_status=0x%x\n",
gp_status);
return -EINVAL;
}
- /* Upon link speed change set the NIG into drain mode.
- Comes to deals with possible FIFO glitch due to clk change
- when speed is decreased without link down indicator */
- if (new_line_speed != vars->line_speed) {
- if (!SINGLE_MEDIA_DIRECT(params) &&
- ext_phy_link_up) {
- DP(NETIF_MSG_LINK, "Internal link speed %d is"
- " different than the external"
- " link speed %d\n", new_line_speed,
- vars->line_speed);
- vars->phy_link_up = 0;
- return 0;
- }
- REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
- + params->port*4, 0);
- msleep(1);
- }
vars->line_speed = new_line_speed;
vars->link_status |= LINK_STATUS_SERDES_LINK;
ext_phy_type = params->phy[EXT_PHY1].type;
}
static u8 bnx2x_emac_program(struct link_params *params,
- u32 line_speed, u32 duplex)
+ struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
(EMAC_MODE_25G_MODE |
EMAC_MODE_PORT_MII_10M |
EMAC_MODE_HALF_DUPLEX));
- switch (line_speed) {
+ switch (vars->line_speed) {
case SPEED_10:
mode |= EMAC_MODE_PORT_MII_10M;
break;
default:
/* 10G not valid for EMAC */
- DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", line_speed);
+ DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
+ vars->line_speed);
return -EINVAL;
}
- if (duplex == DUPLEX_HALF)
+ if (vars->duplex == DUPLEX_HALF)
mode |= EMAC_MODE_HALF_DUPLEX;
bnx2x_bits_en(bp,
GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
mode);
- bnx2x_set_led(params, LED_MODE_OPER, line_speed);
+ bnx2x_set_led(params, LED_MODE_OPER, vars->line_speed);
return 0;
}
+static u8 bnx2x_init_serdes(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u8 rc;
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
+ bnx2x_set_aer_mmd(params, phy);
+ rc = bnx2x_reset_unicore(params, phy, 1);
+ /* reset the SerDes and wait for reset bit return low */
+ if (rc != 0)
+ return rc;
+ bnx2x_set_aer_mmd(params, phy);
+
+ return rc;
+}
+
+static u8 bnx2x_init_xgxs(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u8 rc;
+ vars->phy_flags = PHY_XGXS_FLAG;
+ if ((phy->req_line_speed &&
+ ((phy->req_line_speed == SPEED_100) ||
+ (phy->req_line_speed == SPEED_10))) ||
+ (!phy->req_line_speed &&
+ (phy->speed_cap_mask >=
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
+ (phy->speed_cap_mask <
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+ ))
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ else
+ vars->phy_flags &= ~PHY_SGMII_FLAG;
+
+ bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
+ bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_master_ln(params, phy);
+
+ rc = bnx2x_reset_unicore(params, phy, 0);
+ /* reset the SerDes and wait for reset bit return low */
+ if (rc != 0)
+ return rc;
+
+ bnx2x_set_aer_mmd(params, phy);
+ /* setting the masterLn_def again after the reset */
+ bnx2x_set_master_ln(params, phy);
+ bnx2x_set_swap_lanes(params, phy);
+
+ return rc;
+}
/*****************************************************************************/
/* External Phy section */
/*****************************************************************************/
MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
}
-static void bnx2x_ext_phy_reset(struct bnx2x_phy *phy,
- struct link_params *params,
- struct link_vars *vars)
-{
- struct bnx2x *bp = params->bp;
- DP(NETIF_MSG_LINK, "Port %x: bnx2x_ext_phy_reset\n", params->port);
- /* The PHY reset is controled by GPIO 1
- * Give it 1ms of reset pulse
- */
- switch (phy->type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "XGXS Direct\n");
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- DP(NETIF_MSG_LINK, "XGXS 8705/8706\n");
-
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- /* HW reset */
- bnx2x_ext_phy_hw_reset(bp, params->port);
-
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL, 0xa040);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
-
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 1<<15);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- DP(NETIF_MSG_LINK, "XGXS 8072\n");
-
- /* Unset Low Power Mode and SW reset */
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 1<<15);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
- DP(NETIF_MSG_LINK, "XGXS 8073\n");
-
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- DP(NETIF_MSG_LINK, "XGXS SFX7101\n");
-
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- /* HW reset */
- bnx2x_ext_phy_hw_reset(bp, params->port);
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
- /* Restore normal power mode*/
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
-
- /* HW reset */
- bnx2x_ext_phy_hw_reset(bp, params->port);
-
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 1<<15);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
- msleep(1);
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
- MISC_REGISTERS_GPIO_OUTPUT_HIGH,
- params->port);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
- DP(NETIF_MSG_LINK, "XGXS PHY Failure detected\n");
- break;
- default:
- DP(NETIF_MSG_LINK, "BAD phy type 0x%x\n",
- phy->type);
- break;
- }
-}
-
static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port,
u32 shmem_base, u32 spirom_ver)
{
static void bnx2x_sfp_set_transmitter(struct bnx2x *bp,
struct bnx2x_phy *phy,
+ u8 port,
u8 tx_en)
{
u16 val;
- DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x\n", tx_en);
+ DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x\n",
+ tx_en, port);
/* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
* In case of NOC feature is disabled and power is up, set GPIO control
* as input to enable listening of over-current indication
*/
-
- if (!(params->feature_config_flags &
- FEATURE_CONFIG_BCM8727_NOC) && is_power_up)
+ if (phy->flags & FLAGS_NOC)
+ return;
+ if (!(phy->flags &
+ FLAGS_NOC) && is_power_up)
val = (1<<4);
else
/*
if (rc == 0 ||
(val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) !=
PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
- bnx2x_sfp_set_transmitter(bp, phy, 1);
+ bnx2x_sfp_set_transmitter(bp, phy, params->port, 1);
else
- bnx2x_sfp_set_transmitter(bp, phy, 0);
+ bnx2x_sfp_set_transmitter(bp, phy, params->port, 0);
return rc;
}
/* Disable transmit for this module */
if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
- bnx2x_sfp_set_transmitter(bp, phy, 0);
+ bnx2x_sfp_set_transmitter(bp, phy, params->port, 0);
}
}
CL45_WR_OVER_CL22(bp, phy,
bank,
MDIO_RX0_RX_EQ_BOOST,
- params->xgxs_config_rx[i]);
+ phy->rx_preemphasis[i]);
}
for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3;
CL45_WR_OVER_CL22(bp, phy,
bank,
MDIO_TX0_TX_DRIVER,
- params->xgxs_config_tx[i]);
+ phy->tx_preemphasis[i]);
}
}
}
}
-static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars)
+static u16 bnx2x_wait_reset_complete(struct bnx2x *bp,
+ struct bnx2x_phy *phy)
{
- struct bnx2x *bp = params->bp;
- u16 cnt;
- u16 ctrl = 0;
- u16 val = 0;
- u8 rc = 0;
- struct bnx2x_phy *phy = ¶ms->phy[EXT_PHY1];
- if (vars->phy_flags & PHY_XGXS_FLAG) {
- /* Make sure that the soft reset is off (expect for the 8072:
- * due to the lock, it will be done inside the specific
- * handling)
- */
- if ((phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
- (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) &&
- (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN) &&
- (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) &&
- (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)) {
+ u16 cnt, ctrl;
/* Wait for soft reset to get cleared upto 1 sec */
for (cnt = 0; cnt < 1000; cnt++) {
bnx2x_cl45_read(bp, phy,
}
DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n",
ctrl, cnt);
- }
-
- switch (phy->type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- break;
+ return 0;
+}
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+static u8 bnx2x_8705_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "init 8705\n");
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
+ bnx2x_wait_reset_complete(bp, phy);
DP(NETIF_MSG_LINK, "XGXS 8705\n");
bnx2x_cl45_write(bp, phy,
/* BCM8705 doesn't have microcode, hence the 0 */
bnx2x_save_spirom_version(bp, params->port,
params->shmem_base, 0);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ return 0;
+}
+
+static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u16 cnt, val;
+ struct bnx2x *bp = params->bp;
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
+
+ bnx2x_wait_reset_complete(bp, phy);
/* Wait until fw is loaded */
for (cnt = 0; cnt < 100; cnt++) {
bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
val &= ~0x7;
/* Set control bits according to
configuation */
- val |= (params->xgxs_config_rx[i] &
+ val |= (phy->rx_preemphasis[i] &
0x7);
DP(NETIF_MSG_LINK, "Setting RX"
"Equalizer to BCM8706 reg 0x%x"
bnx2x_save_bcm_spirom_ver(bp, params->port,
phy,
params->shmem_base);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ return 0;
+}
+
+static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "Initializing BCM8726\n");
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+
+ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
+ bnx2x_wait_reset_complete(bp, phy);
+
+ bnx2x_wait_reset_complete(bp, phy);
DP(NETIF_MSG_LINK, "Initializing BCM8726\n");
bnx2x_8726_external_rom_boot(phy, params);
FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
"TX_CTRL2 0x%x\n",
- params->xgxs_config_tx[0],
- params->xgxs_config_tx[1]);
+ phy->tx_preemphasis[0],
+ phy->tx_preemphasis[1]);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8726_TX_CTRL1,
- params->xgxs_config_tx[0]);
+ phy->tx_preemphasis[0]);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8726_TX_CTRL2,
- params->xgxs_config_tx[1]);
+ phy->tx_preemphasis[1]);
}
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ return 0;
+
+}
+
+static u8 bnx2x_8072_8073_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val = 0;
+ u8 gpio_port;
+ DP(NETIF_MSG_LINK, "Init 8073\n");
+
+ gpio_port = params->port;
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
+
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
+
{
u16 tmp1;
u16 rx_alarm_ctrl_val;
bnx2x_807x_force_10G(bp, phy);
DP(NETIF_MSG_LINK,
"Forced speed 10G on 807X\n");
- break;
+ return 0;
} else {
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
"Advertise 1G=%x, 10G=%x\n",
((val & (1<<5)) > 0),
((val & (1<<7)) > 0));
- break;
+ return 0;
}
+}
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
- {
- u16 tmp1;
- u16 rx_alarm_ctrl_val;
- u16 lasi_ctrl_val;
+static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u16 tmp1, val, mod_abs;
+ u16 rx_alarm_ctrl_val;
+ u16 lasi_ctrl_val;
+ struct bnx2x *bp = params->bp;
+ /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */
/* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */
- u16 mod_abs;
rx_alarm_ctrl_val = (1<<2) | (1<<5) ;
lasi_ctrl_val = 0x0004;
-
+ bnx2x_wait_reset_complete(bp, phy);
DP(NETIF_MSG_LINK, "Initializing BCM8727\n");
/* enable LASI */
bnx2x_cl45_write(bp, phy,
FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
"TX_CTRL2 0x%x\n",
- params->xgxs_config_tx[0],
- params->xgxs_config_tx[1]);
+ phy->tx_preemphasis[0],
+ phy->tx_preemphasis[1]);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_TX_CTRL1,
- params->xgxs_config_tx[0]);
+ phy->tx_preemphasis[0]);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_TX_CTRL2,
- params->xgxs_config_tx[1]);
+ phy->tx_preemphasis[1]);
}
- break;
- }
+ return 0;
+}
+
+static u8 bnx2x_7101_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u16 fw_ver1, fw_ver2, val;
+ struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "Setting the SFX7101 LASI indication\n");
+
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- {
- u16 fw_ver1, fw_ver2;
DP(NETIF_MSG_LINK,
"Setting the SFX7101 LASI indication\n");
-
+ bnx2x_wait_reset_complete(bp, phy);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_LASI_CTRL, 0x1);
bnx2x_save_spirom_version(params->bp, params->port,
params->shmem_base,
(u32)(fw_ver1<<16 | fw_ver2));
- break;
- }
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ return 0;
+}
+
+static u8 bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
{
/* This phy uses the NIG latch mechanism since link
indication arrives through its LED4 and not via
u16 autoneg_val, an_1000_val, an_10_100_val, temp;
temp = vars->line_speed;
vars->line_speed = SPEED_10000;
+ bnx2x_wait_reset_complete(bp, phy);
bnx2x_set_autoneg(phy, params, vars, 0);
bnx2x_program_serdes(phy, params, vars);
vars->line_speed = temp;
/* Save spirom version */
bnx2x_save_8481_spirom_version(phy, params,
params->shmem_base);
- break;
+ return 0;
}
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
- DP(NETIF_MSG_LINK,
- "XGXS PHY Failure detected 0x%x\n",
- phy->type);
- rc = -EINVAL;
- break;
+}
- default:
- DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
- phy->type);
- break;
- }
- }
- return rc;
+static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 temp;
+ msleep(1);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+ msleep(200); /* 100 is not enough */
+
+ /**
+ * BCM84823 requires that XGXS links up first @ 10G for normal
+ * behavior
+ */
+ temp = vars->line_speed;
+ vars->line_speed = SPEED_10000;
+ bnx2x_set_autoneg(phy, params, vars, 0);
+ bnx2x_program_serdes(phy, params, vars);
+ vars->line_speed = temp;
+ return bnx2x_848xx_cmn_config_init(phy, params, vars);
}
+static u8 bnx2x_8481_config_init(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
+
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+
+ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
+ return bnx2x_848xx_cmn_config_init(phy, params, vars);
+}
static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy,
struct link_params *params)
{
if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
- bnx2x_sfp_set_transmitter(bp, phy, 0);
+ bnx2x_sfp_set_transmitter(bp, phy, params->port, 0);
if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
bnx2x_sfp_module_detection(phy, params);
module plugged in/out */
}
-
-static u8 bnx2x_ext_phy_is_link_up(struct bnx2x_phy *phy,
+static u8 bnx2x_8705_read_status(struct bnx2x_phy *phy,
struct link_params *params,
- struct link_vars *vars,
- u8 is_mi_int)
+ struct link_vars *vars)
{
- struct bnx2x *bp = params->bp;
- u16 val1 = 0, val2;
- u16 rx_sd, pcs_status;
u8 ext_phy_link_up = 0;
-
- if (vars->phy_flags & PHY_XGXS_FLAG) {
- switch (phy->type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- DP(NETIF_MSG_LINK, "XGXS Direct\n");
- ext_phy_link_up = 1;
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ u16 val1, rx_sd;
+ struct bnx2x *bp = params->bp;
DP(NETIF_MSG_LINK, "XGXS 8705\n");
bnx2x_cl45_read(bp, phy,
MDIO_WIS_DEVAD,
((val1 & (1<<8)) == 0));
if (ext_phy_link_up)
vars->line_speed = SPEED_10000;
- break;
+ return ext_phy_link_up;
+}
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+static u8 bnx2x_8706_8726_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ u8 link_up = 0;
+ u16 val1, val2, rx_sd, pcs_status;
+ struct bnx2x *bp = params->bp;
DP(NETIF_MSG_LINK, "XGXS 8706/8726\n");
/* Clear RX Alarm*/
bnx2x_cl45_read(bp, phy,
* bit 0 of pcs_status are set, or if the autoneg bit
1 is set
*/
- ext_phy_link_up = ((rx_sd & pcs_status & 0x1) ||
- (val2 & (1<<1)));
- if (ext_phy_link_up) {
- if (phy->type ==
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) {
- /* If transmitter is disabled,
- ignore false link up indication */
- bnx2x_cl45_read(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_PHY_IDENTIFIER,
- &val1);
- if (val1 & (1<<15)) {
- DP(NETIF_MSG_LINK, "Tx is "
- "disabled\n");
- ext_phy_link_up = 0;
- break;
- }
- }
+ link_up = ((rx_sd & pcs_status & 0x1) ||
+ (val2 & (1<<1)));
+ if (link_up) {
if (val2 & (1<<1))
vars->line_speed = SPEED_1000;
else
vars->line_speed = SPEED_10000;
+ bnx2x_ext_phy_resolve_fc(phy, params, vars);
+ return link_up;
}
- break;
+ return 0;
+}
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
- {
+static u8 bnx2x_8706_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ return bnx2x_8706_8726_read_status(phy, params, vars);
+}
+
+static u8 bnx2x_8726_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val1;
+ u8 link_up = bnx2x_8706_8726_read_status(phy, params, vars);
+ if (link_up) {
+ bnx2x_cl45_read(bp, phy,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER,
+ &val1);
+ if (val1 & (1<<15)) {
+ DP(NETIF_MSG_LINK, "Tx is disabled\n");
+ link_up = 0;
+ vars->line_speed = 0;
+ }
+ }
+ return link_up;
+}
+static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_link_up = 0;
u16 link_status = 0;
- u16 rx_alarm_status;
+ u16 rx_alarm_status, val1;
/* Check the LASI */
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
* If a module is present and there is need to check
* for over current
*/
- if (!(params->feature_config_flags &
- FEATURE_CONFIG_BCM8727_NOC) &&
+ if (!(phy->flags & FLAGS_NOC) &&
!(rx_alarm_status & (1<<5))) {
/* Check over-current using 8727 GPIO0 input*/
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_RX_ALARM,
&rx_alarm_status);
- break;
+ return ext_phy_link_up;
}
} /* Over current check */
if (val1 & (1<<15)) {
DP(NETIF_MSG_LINK, "Tx is disabled\n");
ext_phy_link_up = 0;
- break;
+ return ext_phy_link_up;
}
bnx2x_cl45_read(bp, phy,
"port %x: External link"
" is down\n", params->port);
}
- break;
- }
+ return ext_phy_link_up;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
- {
+}
+static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_link_up = 0;
+ u16 val1, val2;
u16 link_status = 0;
u16 an1000_status = 0;
if (bnx2x_8073_xaui_wa(bp, phy)
!= 0) {
ext_phy_link_up = 0;
- break;
+ return ext_phy_link_up;
}
}
bnx2x_cl45_read(bp, phy,
}
}
- break;
- }
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ return ext_phy_link_up;
+}
+
+static u8 bnx2x_7101_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_link_up;
+ u16 val1, val2;
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_LASI_STATUS, &val2);
val2,
(val2 & (1<<14)));
}
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ return ext_phy_link_up;
+}
+
+static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy,
+ struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val1, val2;
+ u8 ext_phy_link_up = 0;
+
/* Check 10G-BaseT link status */
/* Check PMD signal ok */
bnx2x_cl45_read(bp, phy,
(vars->duplex == DUPLEX_FULL));
}
}
- break;
- default:
- DP(NETIF_MSG_LINK,
- "BAD SerDes ext_phy_config 0x%x\n",
- phy->type);
- ext_phy_link_up = 0;
- break;
- }
- }
-
- /* Set SGMII mode for external phy */
- if (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
- if (vars->line_speed < SPEED_1000)
- vars->phy_flags |= PHY_SGMII_FLAG;
- else
- vars->phy_flags &= ~PHY_SGMII_FLAG;
- }
-
- return ext_phy_link_up;
+ return ext_phy_link_up;
}
+
static void bnx2x_link_int_enable(struct link_params *params)
{
u8 port = params->port;
}
}
-static u8 bnx2x_format_ver(u32 num, u8 *str, u16 len)
+static u8 bnx2x_7101_format_ver(u32 spirom_ver, u8 *str, u16 *len)
+{
+ if (*len < 5)
+ return -EINVAL;
+ str[0] = (spirom_ver & 0xFF);
+ str[1] = (spirom_ver & 0xFF00) >> 8;
+ str[2] = (spirom_ver & 0xFF0000) >> 16;
+ str[3] = (spirom_ver & 0xFF000000) >> 24;
+ str[4] = '\0';
+ *len -= 5;
+ return 0;
+}
+
+static u8 bnx2x_format_ver(u32 num, u8 *str, u16 *len)
{
u8 *str_ptr = str;
u32 mask = 0xf0000000;
u8 shift = 8*4;
u8 digit;
- if (len < 10) {
+ if (*len < 10) {
/* Need more than 10chars for this format */
*str_ptr = '\0';
return -EINVAL;
return 0;
}
+static u8 bnx2x_848xx_format_ver(u32 raw_ver, u8 *str, u16 *len)
+{
+ u8 status = 0;
+ u32 spirom_ver;
+ spirom_ver = ((raw_ver & 0xF80) >> 7) << 16 | (raw_ver & 0x7F);
+ status = bnx2x_format_ver(spirom_ver, str, len);
+ return status;
+}
+
+static u8 bnx2x_null_format_ver(u32 spirom_ver, u8 *str, u16 *len)
+{
+ str[0] = '\0';
+ (*len)--;
+ return 0;
+}
+
u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
u8 *version, u16 len)
{
struct bnx2x *bp;
- u32 ext_phy_type = 0;
u32 spirom_ver = 0;
- u8 status;
-
+ u8 status = 0;
+ u8 *ver_p = version;
if (version == NULL || params == NULL)
return -EINVAL;
bp = params->bp;
- spirom_ver = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region,
- port_mb[params->port].ext_phy_fw_version));
-
- status = 0;
- /* reset the returned value to zero */
- ext_phy_type = params->phy[EXT_PHY1].type;
- switch (ext_phy_type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
-
- if (len < 5)
- return -EINVAL;
-
- version[0] = (spirom_ver & 0xFF);
- version[1] = (spirom_ver & 0xFF00) >> 8;
- version[2] = (spirom_ver & 0xFF0000) >> 16;
- version[3] = (spirom_ver & 0xFF000000) >> 24;
- version[4] = '\0';
-
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
- status = bnx2x_format_ver(spirom_ver, version, len);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
- spirom_ver = ((spirom_ver & 0xF80) >> 7) << 16 |
- (spirom_ver & 0x7F);
- status = bnx2x_format_ver(spirom_ver, version, len);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- version[0] = '\0';
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
- DP(NETIF_MSG_LINK, "bnx2x_get_ext_phy_fw_version:"
- " type is FAILURE!\n");
- status = -EINVAL;
- break;
+ /* Extract first external phy*/
+ version[0] = '\0';
+ spirom_ver = REG_RD(bp, params->phy[EXT_PHY1].ver_addr);
- default:
- break;
- }
+ if (params->phy[EXT_PHY1].format_fw_ver)
+ status |= params->phy[EXT_PHY1].format_fw_ver(spirom_ver,
+ ver_p,
+ &len);
return status;
}
}
}
-static void bnx2x_ext_phy_loopback(struct bnx2x_phy *phy,
- struct link_params *params)
+static void bnx2x_8726_config_loopback(struct bnx2x_phy *phy,
+ struct link_params *params)
{
struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n");
+ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0001);
+}
- if (params->switch_cfg == SWITCH_CFG_10G) {
-
- /* CL37 Autoneg Enabled */
- switch (phy->type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN:
- DP(NETIF_MSG_LINK,
- "ext_phy_loopback: We should not get here\n");
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
- DP(NETIF_MSG_LINK, "ext_phy_loopback: 8705\n");
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
- DP(NETIF_MSG_LINK, "ext_phy_loopback: 8706\n");
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
- DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n");
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_CTRL,
- 0x0001);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- /* SFX7101_XGXS_TEST1 */
- bnx2x_cl45_write(bp, phy,
- MDIO_XS_DEVAD,
- MDIO_XS_SFX7101_XGXS_TEST1,
- 0x100);
- DP(NETIF_MSG_LINK,
- "ext_phy_loopback: set ext phy loopback\n");
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
-
- break;
- } /* switch external PHY type */
- }
+static void bnx2x_7101_config_loopback(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ /* SFX7101_XGXS_TEST1 */
+ bnx2x_cl45_write(bp, phy,
+ MDIO_XS_DEVAD, MDIO_XS_SFX7101_XGXS_TEST1, 0x100);
}
/*
*------------------------------------------------------------------------
MDIO_GP_STATUS_TOP_AN_STATUS1,
&gp_status);
/* link is up only if both local phy and external phy are up */
- if ((gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) &&
- bnx2x_ext_phy_is_link_up(¶ms->phy[EXT_PHY1], params, vars, 1))
- return 0;
+ if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
+ u8 ext_phy_link_up = 1;
+ struct link_vars temp_vars;
+ if (params->phy[EXT_PHY1].read_status)
+ ext_phy_link_up &=
+ params->phy[EXT_PHY1].read_status(
+ ¶ms->phy[EXT_PHY1],
+ params, &temp_vars);
+ if (ext_phy_link_up)
+ return 0;
+ }
return -ESRCH;
}
struct bnx2x *bp = params->bp;
u8 port = params->port;
u8 rc = 0;
- u8 non_ext_phy;
+ u8 phy_index, non_ext_phy;
struct bnx2x_phy *ext_phy = ¶ms->phy[EXT_PHY1];
struct bnx2x_phy *int_phy = ¶ms->phy[INT_PHY];
/* Activate the external PHY */
- bnx2x_ext_phy_reset(ext_phy, params, vars);
bnx2x_set_aer_mmd(params, int_phy);
}
if (!non_ext_phy)
- rc |= bnx2x_ext_phy_init(params, vars);
+ for (phy_index = EXT_PHY1; phy_index < params->num_phys;
+ phy_index++) {
+ params->phy[phy_index].config_init(
+ ¶ms->phy[phy_index],
+ params, vars);
+ }
bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
(NIG_STATUS_XGXS0_LINK10G |
return rc;
}
+static void set_phy_vars(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 actual_phy_idx, phy_index;
+
+ for (phy_index = INT_PHY; phy_index < params->num_phys;
+ phy_index++) {
+
+ actual_phy_idx = phy_index;
+ params->phy[actual_phy_idx].req_flow_ctrl =
+ params->req_flow_ctrl;
+
+ params->phy[actual_phy_idx].req_line_speed =
+ params->req_line_speed;
+
+ params->phy[actual_phy_idx].speed_cap_mask =
+ params->speed_cap_mask;
+
+ params->phy[actual_phy_idx].req_duplex =
+ params->req_duplex;
+
+ DP(NETIF_MSG_LINK, "req_flow_ctrl %x, req_line_speed %x,"
+ " speed_cap_mask %x\n",
+ params->phy[actual_phy_idx].req_flow_ctrl,
+ params->phy[actual_phy_idx].req_line_speed,
+ params->phy[actual_phy_idx].speed_cap_mask);
+ }
+}
+
u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
vars->duplex = DUPLEX_FULL;
vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
vars->mac_type = MAC_TYPE_NONE;
-
- if (params->switch_cfg == SWITCH_CFG_1G) {
- params->phy[INT_PHY].type =
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT;
- vars->phy_flags = PHY_SERDES_FLAG;
- } else {
- params->phy[INT_PHY].type =
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT;
- vars->phy_flags = PHY_XGXS_FLAG;
- }
- params->phy[INT_PHY].mdio_ctrl =
- bnx2x_get_emac_base(bp,
- params->phy[INT_PHY].type, params->port);
- if (XGXS_EXT_PHY_TYPE(params->ext_phy_config) !=
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
- params->phy[EXT_PHY1].type =
- XGXS_EXT_PHY_TYPE(params->ext_phy_config);
- params->phy[EXT_PHY1].addr =
- XGXS_EXT_PHY_ADDR(params->ext_phy_config);
- params->phy[EXT_PHY1].mdio_ctrl =
- bnx2x_get_emac_base(bp, params->phy[EXT_PHY1].type,
- params->port);
- }
+ vars->phy_flags = 0;
/* disable attentions */
bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
bnx2x_emac_init(params, vars);
+ if (params->num_phys == 0) {
+ DP(NETIF_MSG_LINK, "No phy found for initialization !!\n");
+ return -EINVAL;
+ }
+ set_phy_vars(params);
+
+ DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys);
if (CHIP_REV_IS_FPGA(bp)) {
vars->link_up = 1;
bnx2x_phy_deassert(params, vars->phy_flags);
/* set bmac loopback */
bnx2x_emac_enable(params, vars, 1);
- bnx2x_emac_program(params, vars->line_speed,
- vars->duplex);
+ bnx2x_emac_program(params, vars);
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
params->port*4, 0);
val = REG_RD(bp,
NIG_REG_XGXS0_CTRL_PHY_ADDR+
params->port*0x18);
- params->phy_addr = (u8)val;
- params->phy[INT_PHY].addr = (u8)val;
+
bnx2x_phy_deassert(params, vars->phy_flags);
bnx2x_link_initialize(params, vars);
if (params->loopback_mode == LOOPBACK_XGXS_10) {
/* set 10G XGXS loopback */
- bnx2x_set_xgxs_loopback(¶ms->phy[INT_PHY],
- params, 1);
+ params->phy[INT_PHY].config_loopback(
+ ¶ms->phy[INT_PHY],
+ params);
+
} else {
/* set external phy loopback */
- bnx2x_ext_phy_loopback(¶ms->phy[INT_PHY],
+ u8 phy_index;
+ for (phy_index = EXT_PHY1;
+ phy_index < params->num_phys; phy_index++) {
+ if (params->phy[phy_index].config_loopback)
+ params->phy[phy_index].config_loopback(
+ ¶ms->phy[phy_index],
params);
+ }
}
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
} else
/* No loopback */
{
+ if (params->switch_cfg == SWITCH_CFG_10G)
+ vars->phy_flags = PHY_XGXS_FLAG;
bnx2x_phy_deassert(params, vars->phy_flags);
- switch (params->switch_cfg) {
- case SWITCH_CFG_1G:
- vars->phy_flags |= PHY_SERDES_FLAG;
- if ((params->ext_phy_config &
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK) ==
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482) {
- vars->phy_flags |= PHY_SGMII_FLAG;
- }
-
- val = REG_RD(bp,
- NIG_REG_SERDES0_CTRL_PHY_ADDR+
- params->port*0x10);
-
- params->phy_addr = (u8)val;
-
- break;
- case SWITCH_CFG_10G:
- vars->phy_flags |= PHY_XGXS_FLAG;
- val = REG_RD(bp,
- NIG_REG_XGXS0_CTRL_PHY_ADDR+
- params->port*0x18);
- params->phy_addr = (u8)val;
-
- break;
- default:
- DP(NETIF_MSG_LINK, "Invalid switch_cfg\n");
- return -EINVAL;
- }
- DP(NETIF_MSG_LINK, "Phy address = 0x%x\n", params->phy_addr);
- params->phy[INT_PHY].addr = params->phy_addr;
bnx2x_link_initialize(params, vars);
msleep(30);
bnx2x_link_int_enable(params);
}
-static void bnx2x_8726_reset_phy(struct bnx2x *bp,
- struct bnx2x_phy *phy)
+static void bnx2x_8726_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
{
- DP(NETIF_MSG_LINK, "bnx2x_8726_reset_phy\n");
+ struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "bnx2x_8726_link_reset port %d\n", params->port);
/* Set serial boot control for external load */
bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_GEN_CTRL, 0x0001);
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL, 0x0001);
+}
+
+static void bnx2x_8727_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ /* Disable Transmitter */
+ bnx2x_sfp_set_transmitter(bp, phy, params->port, 0);
+}
+static void bnx2x_8073_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 gpio_port;
+ gpio_port = params->port;
+ DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n",
+ gpio_port);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
+}
+static void bnx2x_8481_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ bnx2x_cl45_write(params->bp, phy,
+ MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000);
+ bnx2x_cl45_write(params->bp, phy,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1);
+}
+
+static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ port);
+}
+
+static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 gpio_port;
+ /* HW reset */
+ gpio_port = params->port;
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ gpio_port);
+ DP(NETIF_MSG_LINK, "reset external PHY\n");
+}
+
+static void bnx2x_int_link_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ /* reset the SerDes/XGXS */
+ REG_WR(params->bp, GRCBASE_MISC +
+ MISC_REGISTERS_RESET_REG_3_CLEAR,
+ (0x1ff << (params->port*16)));
}
u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
{
struct bnx2x *bp = params->bp;
- u8 port = params->port;
+ u8 phy_index, port = params->port;
- u32 val = REG_RD(bp, params->shmem_base +
- offsetof(struct shmem_region, dev_info.
- port_feature_config[params->port].
- config));
DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port);
/* disable attentions */
vars->link_status = 0;
/* clear link led */
bnx2x_set_led(params, LED_MODE_OFF, 0);
if (reset_ext_phy) {
- struct bnx2x_phy *phy = ¶ms->phy[EXT_PHY1];
- switch (phy->type) {
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
- break;
-
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
- {
-
- /* Disable Transmitter */
- if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
- PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
- bnx2x_sfp_set_transmitter(bp, phy, 0);
- break;
- }
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
- DP(NETIF_MSG_LINK, "Setting 8073 port %d into "
- "low power mode\n",
- port);
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- port);
- break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
- {
- /* Set soft reset */
- bnx2x_8726_reset_phy(bp, phy);
- break;
- }
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
- {
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- params->port);
- break;
- }
- default:
- /* HW reset */
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- port);
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
- MISC_REGISTERS_GPIO_OUTPUT_LOW,
- port);
- DP(NETIF_MSG_LINK, "reset external PHY\n");
+ for (phy_index = EXT_PHY1; phy_index < params->num_phys;
+ phy_index++) {
+ if (params->phy[phy_index].link_reset)
+ params->phy[phy_index].link_reset(
+ ¶ms->phy[phy_index],
+ params);
}
}
- /* reset the SerDes/XGXS */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
- (0x1ff << (port*16)));
+ if (params->phy[INT_PHY].link_reset)
+ params->phy[INT_PHY].link_reset(
+ ¶ms->phy[INT_PHY], params);
/* reset BigMac */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
static u8 bnx2x_update_link_up(struct link_params *params,
struct link_vars *vars,
- u8 link_10g, u32 gp_status)
+ u8 link_10g)
{
struct bnx2x *bp = params->bp;
u8 port = params->port;
bnx2x_bmac_enable(params, vars, 0);
bnx2x_set_led(params, LED_MODE_OPER, SPEED_10000);
} else {
- rc = bnx2x_emac_program(params, vars->line_speed,
- vars->duplex);
+ rc = bnx2x_emac_program(params, vars);
bnx2x_emac_enable(params, vars, 0);
msleep(20);
return rc;
}
-/* This function should called upon link interrupt */
-/* In case vars->link_up, driver needs to
- 1. Update the pbf
- 2. Disable drain
- 3. Update the shared memory
- 4. Indicate link up
- 5. Set LEDs
- Otherwise,
- 1. Update shared memory
- 2. Reset BigMac
- 3. Report link down
- 4. Unset LEDs
+/**
+ * The bnx2x_link_update function should be called upon link
+ * interrupt.
+ * Link is considered up as follows:
+ * - DIRECT_SINGLE_MEDIA - Only XGXS link (internal link) needs
+ * to be up
+ * - SINGLE_MEDIA - The link between the 577xx and the external
+ * phy (XGXS) need to up as well as the external link of the
+ * phy (PHY_EXT1)
+ * - DUAL_MEDIA - The link between the 577xx and the first
+ * external phy needs to be up, and at least one of the 2
+ * external phy link must be up.
*/
u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
+ struct link_vars phy_vars[MAX_PHYS];
u8 port = params->port;
- u16 gp_status;
- u8 link_10g;
- u8 ext_phy_link_up, rc = 0;
- struct bnx2x_phy *int_phy = ¶ms->phy[INT_PHY];
+ u8 link_10g, phy_index;
+ u8 ext_phy_link_up = 0, cur_link_up, rc = 0;
u8 is_mi_int = 0;
+ u16 ext_phy_line_speed = 0, prev_line_speed = vars->line_speed;
+ u8 active_external_phy = INT_PHY;
+ vars->link_status = 0;
+ for (phy_index = INT_PHY; phy_index < params->num_phys;
+ phy_index++) {
+ phy_vars[phy_index].flow_ctrl = 0;
+ phy_vars[phy_index].link_status = 0;
+ phy_vars[phy_index].line_speed = 0;
+ phy_vars[phy_index].duplex = DUPLEX_FULL;
+ phy_vars[phy_index].phy_link_up = 0;
+ phy_vars[phy_index].link_up = 0;
+ }
DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n",
port, (vars->phy_flags & PHY_XGXS_FLAG),
/* disable emac */
REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
- /* Check external link change only for non-direct */
- ext_phy_link_up = bnx2x_ext_phy_is_link_up(¶ms->phy[EXT_PHY1],
- params, vars,
- is_mi_int);
+ /**
+ * Step 1:
+ * Check external link change only for external phys, and apply
+ * priority selection between them in case the link on both phys
+ * is up. Note that the instead of the common vars, a temporary
+ * vars argument is used since each phy may have different link/
+ * speed/duplex result
+ */
+ for (phy_index = EXT_PHY1; phy_index < params->num_phys;
+ phy_index++) {
+ struct bnx2x_phy *phy = ¶ms->phy[phy_index];
+ if (!phy->read_status)
+ continue;
+ /* Read link status and params of this ext phy */
+ cur_link_up = phy->read_status(phy, params,
+ &phy_vars[phy_index]);
+ if (cur_link_up) {
+ DP(NETIF_MSG_LINK, "phy in index %d link is up\n",
+ phy_index);
+ } else {
+ DP(NETIF_MSG_LINK, "phy in index %d link is down\n",
+ phy_index);
+ continue;
+ }
- /* Read gp_status */
- CL45_RD_OVER_CL22(bp, int_phy,
- MDIO_REG_BANK_GP_STATUS,
- MDIO_GP_STATUS_TOP_AN_STATUS1,
- &gp_status);
+ if (!ext_phy_link_up) {
+ ext_phy_link_up = 1;
+ active_external_phy = phy_index;
+ }
+ }
+ prev_line_speed = vars->line_speed;
+ /**
+ * Step 2:
+ * Read the status of the internal phy. In case of
+ * DIRECT_SINGLE_MEDIA board, this link is the external link,
+ * otherwise this is the link between the 577xx and the first
+ * external phy
+ */
+ if (params->phy[INT_PHY].read_status)
+ params->phy[INT_PHY].read_status(
+ ¶ms->phy[INT_PHY],
+ params, vars);
+ /**
+ * The INT_PHY flow control reside in the vars. This include the
+ * case where the speed or flow control are not set to AUTO.
+ * Otherwise, the active external phy flow control result is set
+ * to the vars. The ext_phy_line_speed is needed to check if the
+ * speed is different between the internal phy and external phy.
+ * This case may be result of intermediate link speed change.
+ */
+ if (active_external_phy > INT_PHY) {
+ vars->flow_ctrl = phy_vars[active_external_phy].flow_ctrl;
+ /**
+ * Link speed is taken from the XGXS. AN and FC result from
+ * the external phy.
+ */
+ vars->link_status |= phy_vars[active_external_phy].link_status;
+ ext_phy_line_speed = phy_vars[active_external_phy].line_speed;
+ vars->duplex = phy_vars[active_external_phy].duplex;
+ if (params->phy[active_external_phy].supported &
+ SUPPORTED_FIBRE)
+ vars->link_status |= LINK_STATUS_SERDES_LINK;
+ DP(NETIF_MSG_LINK, "Active external phy selected: %x\n",
+ active_external_phy);
+ }
+ DP(NETIF_MSG_LINK, "vars->flow_ctrl = 0x%x, vars->link_status = 0x%x,"
+ " ext_phy_line_speed = %d\n", vars->flow_ctrl,
+ vars->link_status, ext_phy_line_speed);
+ /**
+ * Upon link speed change set the NIG into drain mode. Comes to
+ * deals with possible FIFO glitch due to clk change when speed
+ * is decreased without link down indicator
+ */
- rc = bnx2x_link_settings_status(params, vars, gp_status,
- ext_phy_link_up);
- if (rc != 0)
- return rc;
+ if (vars->phy_link_up) {
+ if (!(SINGLE_MEDIA_DIRECT(params)) && ext_phy_link_up &&
+ (ext_phy_line_speed != vars->line_speed)) {
+ DP(NETIF_MSG_LINK, "Internal link speed %d is"
+ " different than the external"
+ " link speed %d\n", vars->line_speed,
+ ext_phy_line_speed);
+ vars->phy_link_up = 0;
+ } else if (prev_line_speed != vars->line_speed) {
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+ + params->port*4, 0);
+ msleep(1);
+ }
+ }
/* anything 10 and over uses the bmac */
link_10g = ((vars->line_speed == SPEED_10000) ||
bnx2x_link_int_ack(params, vars, link_10g, is_mi_int);
- /* In case external phy link is up, and internal link is down
- ( not initialized yet probably after link initialization, it needs
- to be initialized.
- Note that after link down-up as result of cable plug,
- the xgxs link would probably become up again without the need to
- initialize it*/
-
- if ((int_phy->type != PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) &&
- (int_phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) &&
- (int_phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) &&
- (int_phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) &&
- (int_phy->type && !vars->phy_link_up))
- bnx2x_init_internal_phy(int_phy, params, vars);
-
- /* link is up only if both local phy and external phy are up */
- vars->link_up = (ext_phy_link_up && vars->phy_link_up);
+ /**
+ * In case external phy link is up, and internal link is down
+ * (not initialized yet probably after link initialization, it
+ * needs to be initialized.
+ * Note that after link down-up as result of cable plug, the xgxs
+ * link would probably become up again without the need
+ * initialize it
+ */
+ if (!(SINGLE_MEDIA_DIRECT(params))) {
+ DP(NETIF_MSG_LINK, "ext_phy_link_up = %d, int_link_up = %d,"
+ " init_preceding = %d\n", ext_phy_link_up,
+ vars->phy_link_up,
+ params->phy[EXT_PHY1].flags &
+ FLAGS_INIT_XGXS_FIRST);
+ if (!(params->phy[EXT_PHY1].flags &
+ FLAGS_INIT_XGXS_FIRST)
+ && ext_phy_link_up && !vars->phy_link_up) {
+ vars->line_speed = ext_phy_line_speed;
+ if (vars->line_speed < SPEED_1000)
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ else
+ vars->phy_flags &= ~PHY_SGMII_FLAG;
+ bnx2x_init_internal_phy(¶ms->phy[INT_PHY],
+ params,
+ vars);
+ }
+ }
+ /**
+ * Link is up only if both local phy and external phy (in case of
+ * non-direct board) are up
+ */
+ vars->link_up = (vars->phy_link_up &&
+ (ext_phy_link_up ||
+ SINGLE_MEDIA_DIRECT(params)));
if (vars->link_up)
- rc = bnx2x_update_link_up(params, vars, link_10g, gp_status);
+ rc = bnx2x_update_link_up(params, vars, link_10g);
else
rc = bnx2x_update_link_down(params, vars);
return rc;
}
+static void bnx2x_8481_hw_reset(struct bnx2x_phy *phy,
+ struct link_params *params)
+{
+ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, 0);
+ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, 1);
+}
+
+static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy,
+ struct link_params *params) {
+ u32 swap_val, swap_override;
+ u8 port;
+ /**
+ * The PHY reset is controlled by GPIO 1. Fake the port number
+ * to cancel the swap done in set_gpio()
+ */
+ struct bnx2x *bp = params->bp;
+ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+ swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
+ port = (swap_val && swap_override) ^ 1;
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+}
+
+static void bnx2x_7101_hw_reset(struct bnx2x_phy *phy,
+ struct link_params *params) {
+ /* Low power mode is controlled by GPIO 2 */
+ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
+ /* The PHY reset is controlled by GPIO 1 */
+ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
+}
+/******************************************************************/
+/* STATIC PHY DECLARATION */
+/******************************************************************/
+
+static struct bnx2x_phy phy_null = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN,
+ .addr = 0,
+ .flags = FLAGS_INIT_XGXS_FIRST,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = 0,
+ .media_type = ETH_PHY_NOT_PRESENT,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)NULL,
+ .read_status = (read_status_t)NULL,
+ .link_reset = (link_reset_t)NULL,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)NULL,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_serdes = {
+ .type = PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT,
+ .addr = 0xff,
+ .flags = 0,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_2500baseX_Full |
+ SUPPORTED_TP |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_UNSPECIFIED,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_init_serdes,
+ .read_status = (read_status_t)bnx2x_link_settings_status,
+ .link_reset = (link_reset_t)bnx2x_int_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)NULL,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_xgxs = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT,
+ .addr = 0xff,
+ .flags = 0,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_2500baseX_Full |
+ SUPPORTED_10000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_UNSPECIFIED,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_init_xgxs,
+ .read_status = (read_status_t)bnx2x_link_settings_status,
+ .link_reset = (link_reset_t)bnx2x_int_link_reset,
+ .config_loopback = (config_loopback_t)bnx2x_set_xgxs_loopback,
+ .format_fw_ver = (format_fw_ver_t)NULL,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_7101 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
+ .addr = 0xff,
+ .flags = FLAGS_FAN_FAILURE_DET_REQ,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_TP |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_BASE_T,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_7101_config_init,
+ .read_status = (read_status_t)bnx2x_7101_read_status,
+ .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
+ .config_loopback = (config_loopback_t)bnx2x_7101_config_loopback,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_7101_format_ver,
+ .hw_reset = (hw_reset_t)bnx2x_7101_hw_reset,
+ .set_link_led = (set_link_led_t)NULL
+};
+static struct bnx2x_phy phy_8073 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ .addr = 0xff,
+ .flags = FLAGS_HW_LOCK_REQUIRED,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_2500baseX_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_UNSPECIFIED,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8072_8073_config_init,
+ .read_status = (read_status_t)bnx2x_8073_read_status,
+ .link_reset = (link_reset_t)bnx2x_8073_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+static struct bnx2x_phy phy_8705 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705,
+ .addr = 0xff,
+ .flags = FLAGS_INIT_XGXS_FIRST,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_XFP_FIBER,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8705_config_init,
+ .read_status = (read_status_t)bnx2x_8705_read_status,
+ .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_null_format_ver,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+static struct bnx2x_phy phy_8706 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706,
+ .addr = 0xff,
+ .flags = FLAGS_INIT_XGXS_FIRST,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_SFP_FIBER,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8706_config_init,
+ .read_status = (read_status_t)bnx2x_8706_read_status,
+ .link_reset = (link_reset_t)bnx2x_common_ext_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_8726 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ .addr = 0xff,
+ .flags = (FLAGS_HW_LOCK_REQUIRED |
+ FLAGS_INIT_XGXS_FIRST),
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_SFP_FIBER,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8726_config_init,
+ .read_status = (read_status_t)bnx2x_8726_read_status,
+ .link_reset = (link_reset_t)bnx2x_8726_link_reset,
+ .config_loopback = (config_loopback_t)bnx2x_8726_config_loopback,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_8727 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ .addr = 0xff,
+ .flags = FLAGS_FAN_FAILURE_DET_REQ,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10000baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_SFP_FIBER,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8727_config_init,
+ .read_status = (read_status_t)bnx2x_8727_read_status,
+ .link_reset = (link_reset_t)bnx2x_8727_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver,
+ .hw_reset = (hw_reset_t)bnx2x_8727_hw_reset,
+ .set_link_led = (set_link_led_t)NULL
+};
+static struct bnx2x_phy phy_8481 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ .addr = 0xff,
+ .flags = FLAGS_FAN_FAILURE_DET_REQ,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_10000baseT_Full |
+ SUPPORTED_TP |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_BASE_T,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_8481_config_init,
+ .read_status = (read_status_t)bnx2x_848xx_read_status,
+ .link_reset = (link_reset_t)bnx2x_8481_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver,
+ .hw_reset = (hw_reset_t)bnx2x_8481_hw_reset,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+static struct bnx2x_phy phy_84823 = {
+ .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823,
+ .addr = 0xff,
+ .flags = FLAGS_FAN_FAILURE_DET_REQ,
+ .def_md_devad = 0,
+ .reserved = 0,
+ .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff},
+ .mdio_ctrl = 0,
+ .supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_10000baseT_Full |
+ SUPPORTED_TP |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause),
+ .media_type = ETH_PHY_BASE_T,
+ .ver_addr = 0,
+ .req_flow_ctrl = 0,
+ .req_line_speed = 0,
+ .speed_cap_mask = 0,
+ .req_duplex = 0,
+ .rsrv = 0,
+ .config_init = (config_init_t)bnx2x_848x3_config_init,
+ .read_status = (read_status_t)bnx2x_848xx_read_status,
+ .link_reset = (link_reset_t)bnx2x_848x3_link_reset,
+ .config_loopback = (config_loopback_t)NULL,
+ .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver,
+ .hw_reset = (hw_reset_t)NULL,
+ .set_link_led = (set_link_led_t)NULL
+};
+
+/*****************************************************************/
+/* */
+/* Populate the phy according. Main function: bnx2x_populate_phy */
+/* */
+/*****************************************************************/
+
+static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base,
+ struct bnx2x_phy *phy, u8 port,
+ u8 phy_index)
+{
+ /* Get the 4 lanes xgxs config rx and tx */
+ u32 rx = 0, tx = 0, i;
+ for (i = 0; i < 2; i++) {
+ /**
+ * INT_PHY and EXT_PHY1 share the same value location in the
+ * shmem. When num_phys is greater than 1, than this value
+ * applies only to EXT_PHY1
+ */
+
+ rx = REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].xgxs_config_rx[i<<1]));
+
+ tx = REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].xgxs_config_tx[i<<1]));
+
+ phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff);
+ phy->rx_preemphasis[(i << 1) + 1] = (rx & 0xffff);
+
+ phy->tx_preemphasis[i << 1] = ((tx>>16) & 0xffff);
+ phy->tx_preemphasis[(i << 1) + 1] = (tx & 0xffff);
+ }
+}
+
static u32 bnx2x_get_ext_phy_config(struct bnx2x *bp, u32 shmem_base,
u8 phy_index, u8 port)
{
return ext_phy_config;
}
+static u8 bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port,
+ struct bnx2x_phy *phy)
+{
+ u32 phy_addr;
+ u32 chip_id;
+ u32 switch_cfg = (REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_feature_config[port].link_config)) &
+ PORT_FEATURE_CONNECTED_SWITCH_MASK);
+ chip_id = REG_RD(bp, MISC_REG_CHIP_NUM) << 16;
+ switch (switch_cfg) {
+ case SWITCH_CFG_1G:
+ phy_addr = REG_RD(bp,
+ NIG_REG_SERDES0_CTRL_PHY_ADDR +
+ port * 0x10);
+ *phy = phy_serdes;
+ break;
+ case SWITCH_CFG_10G:
+ phy_addr = REG_RD(bp,
+ NIG_REG_XGXS0_CTRL_PHY_ADDR +
+ port * 0x18);
+ *phy = phy_xgxs;
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "Invalid switch_cfg\n");
+ return -EINVAL;
+ }
+ phy->addr = (u8)phy_addr;
+ phy->mdio_ctrl = bnx2x_get_emac_base(bp,
+ phy->type,
+ port);
+ phy->def_md_devad = DEFAULT_PHY_DEV_ADDR;
+
+ DP(NETIF_MSG_LINK, "Internal phy port=%d, addr=0x%x, mdio_ctl=0x%x\n",
+ port, phy->addr, phy->mdio_ctrl);
+
+ bnx2x_populate_preemphasis(bp, shmem_base, phy, port, INT_PHY);
+ return 0;
+}
static u8 bnx2x_populate_ext_phy(struct bnx2x *bp,
u8 phy_index,
u8 port,
struct bnx2x_phy *phy)
{
- u32 ext_phy_config;
+ u32 ext_phy_config, phy_type;
ext_phy_config = bnx2x_get_ext_phy_config(bp, shmem_base,
phy_index, port);
- phy->type = XGXS_EXT_PHY_TYPE(ext_phy_config);
+ phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
+ /* Select the phy type */
+ switch (phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ *phy = phy_8073;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ *phy = phy_8705;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ *phy = phy_8706;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ *phy = phy_8726;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
+ /* BCM8727_NOC => BCM8727 no over current */
+ *phy = phy_8727;
+ phy->flags |= FLAGS_NOC;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ *phy = phy_8727;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
+ *phy = phy_8481;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ *phy = phy_84823;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ *phy = phy_7101;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ *phy = phy_null;
+ return -EINVAL;
+ default:
+ *phy = phy_null;
+ return 0;
+ }
+
phy->addr = XGXS_EXT_PHY_ADDR(ext_phy_config);
+ bnx2x_populate_preemphasis(bp, shmem_base, phy, port, phy_index);
phy->mdio_ctrl = bnx2x_get_emac_base(bp, phy->type, port);
return 0;
}
u8 port, struct bnx2x_phy *phy)
{
u8 status = 0;
+ phy->type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN;
+ if (phy_index == INT_PHY)
+ return bnx2x_populate_int_phy(bp, shmem_base, port, phy);
status = bnx2x_populate_ext_phy(bp, phy_index, shmem_base,
port, phy);
return status;
}
+static void bnx2x_phy_def_cfg(struct link_params *params,
+ struct bnx2x_phy *phy,
+ u8 actual_phy_idx)
+{
+ struct bnx2x *bp = params->bp;
+ u32 link_config;
+ /* Populate the default phy configuration for MF mode */
+ link_config = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].link_config));
+ phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_hw_config[params->port].speed_capability_mask));
+
+ phy->req_duplex = DUPLEX_FULL;
+ switch (link_config & PORT_FEATURE_LINK_SPEED_MASK) {
+ case PORT_FEATURE_LINK_SPEED_10M_HALF:
+ phy->req_duplex = DUPLEX_HALF;
+ case PORT_FEATURE_LINK_SPEED_10M_FULL:
+ phy->req_line_speed = SPEED_10;
+ break;
+ case PORT_FEATURE_LINK_SPEED_100M_HALF:
+ phy->req_duplex = DUPLEX_HALF;
+ case PORT_FEATURE_LINK_SPEED_100M_FULL:
+ phy->req_line_speed = SPEED_100;
+ break;
+ case PORT_FEATURE_LINK_SPEED_1G:
+ phy->req_line_speed = SPEED_1000;
+ break;
+ case PORT_FEATURE_LINK_SPEED_2_5G:
+ phy->req_line_speed = SPEED_2500;
+ break;
+ case PORT_FEATURE_LINK_SPEED_10G_CX4:
+ phy->req_line_speed = SPEED_10000;
+ break;
+ default:
+ phy->req_line_speed = SPEED_AUTO_NEG;
+ break;
+ }
+
+ switch (link_config & PORT_FEATURE_FLOW_CONTROL_MASK) {
+ case PORT_FEATURE_FLOW_CONTROL_AUTO:
+ phy->req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO;
+ break;
+ case PORT_FEATURE_FLOW_CONTROL_TX:
+ phy->req_flow_ctrl = BNX2X_FLOW_CTRL_TX;
+ break;
+ case PORT_FEATURE_FLOW_CONTROL_RX:
+ phy->req_flow_ctrl = BNX2X_FLOW_CTRL_RX;
+ break;
+ case PORT_FEATURE_FLOW_CONTROL_BOTH:
+ phy->req_flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
+ break;
+ default:
+ phy->req_flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ break;
+ }
+}
+
+u8 bnx2x_phy_probe(struct link_params *params)
+{
+ u8 phy_index, actual_phy_idx, link_cfg_idx;
+
+ struct bnx2x *bp = params->bp;
+ struct bnx2x_phy *phy;
+ params->num_phys = 0;
+ DP(NETIF_MSG_LINK, "Begin phy probe\n");
+
+ for (phy_index = INT_PHY; phy_index < MAX_PHYS;
+ phy_index++) {
+ link_cfg_idx = LINK_CONFIG_IDX(phy_index);
+ actual_phy_idx = phy_index;
+
+ phy = ¶ms->phy[actual_phy_idx];
+ if (bnx2x_populate_phy(bp, phy_index, params->shmem_base,
+ params->port,
+ phy) != 0) {
+ params->num_phys = 0;
+ DP(NETIF_MSG_LINK, "phy probe failed in phy index %d\n",
+ phy_index);
+ for (phy_index = INT_PHY;
+ phy_index < MAX_PHYS;
+ phy_index++)
+ *phy = phy_null;
+ return -EINVAL;
+ }
+ if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)
+ break;
+
+ bnx2x_phy_def_cfg(params, phy, actual_phy_idx);
+ params->num_phys++;
+ }
+
+ DP(NETIF_MSG_LINK, "End phy probe. #phys found %x\n", params->num_phys);
+ return 0;
+}
+
+u32 bnx2x_supported_attr(struct link_params *params, u8 phy_idx)
+{
+ if (phy_idx < params->num_phys)
+ return params->phy[phy_idx].supported;
+ return 0;
+}
+
+
static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base)
{
struct bnx2x_phy phy[PORT_MAX];
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff