REPLY_TX_PWR_TABLE_CMD = 0x97,
MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
- /* Bluetooth device coexistance config command */
+ /* Bluetooth device coexistence config command */
REPLY_BT_CONFIG = 0x9b,
/* Statistics */
u8 cmd; /* Command ID: REPLY_RXON, etc. */
u8 flags; /* IWL_CMD_* */
/*
- * The driver sets up the sequence number to values of its chosing.
+ * The driver sets up the sequence number to values of its choosing.
* uCode does not use this value, but passes it back to the driver
* when sending the response to each driver-originated command, so
* the driver can match the response to the command. Since the values
*
* 3945 and 4965 support hardware handshake with Bluetooth device on
* same platform. Bluetooth device alerts wireless device when it will Tx;
- * wireless device can delay or kill its own Tx to accomodate.
+ * wireless device can delay or kill its own Tx to accommodate.
*/
struct iwl3945_bt_cmd {
u8 flags;
* _iwl3945_read32.)
*
* These declarations are *extremely* useful in quickly isolating code deltas
- * which result in misconfiguring of the hardware I/O. In combination with
+ * which result in misconfiguration of the hardware I/O. In combination with
* git-bisect and the IO debug level you can quickly determine the specific
* commit which breaks the IO sequence to the hardware.
*
* priv->eeprom is used to determine if antenna AUX/MAIN are reversed
* priv->antenna specifies the antenna diversity mode:
*
- * IWL_ANTENNA_DIVERISTY - NIC selects best antenna by itself
+ * IWL_ANTENNA_DIVERSITY - NIC selects best antenna by itself
* IWL_ANTENNA_MAIN - Force MAIN antenna
* IWL_ANTENNA_AUX - Force AUX antenna
*/
ref_temp = (s16)priv->eeprom.groups[ch_info->group_index].
temperature;
- /* get power index adjustment based on curr and factory
+ /* get power index adjustment based on current and factory
* temps */
delta_index = iwl3945_hw_reg_adjust_power_by_temp(temperature,
ref_temp);
#include "iwl-fh.h"
-/* EERPROM */
+/* EEPROM */
#define IWL4965_EEPROM_IMG_SIZE 1024
/*
* that target txpower.
*
*
- * 3) Determine (EEPROM) calibration subband for the target channel, by
- * comparing against first and last channels in each subband
+ * 3) Determine (EEPROM) calibration sub band for the target channel, by
+ * comparing against first and last channels in each sub band
* (see struct iwl4965_eeprom_calib_subband_info).
*
*
* 4) Linearly interpolate (EEPROM) factory calibration measurement sets,
- * referencing the 2 factory-measured (sample) channels within the subband.
+ * referencing the 2 factory-measured (sample) channels within the sub band.
*
* Interpolation is based on difference between target channel's frequency
* and the sample channels' frequencies. Since channel numbers are based
* to interpolating based on channel number differences.
*
* Note that the sample channels may or may not be the channels at the
- * edges of the subband. The target channel may be "outside" of the
+ * edges of the sub band. The target channel may be "outside" of the
* span of the sampled channels.
*
* Driver may choose the pair (for 2 Tx chains) of measurements (see
* "4965 temperature calculation".
*
* If current temperature is higher than factory temperature, driver must
- * increase gain (lower gain table index), and vice versa.
+ * increase gain (lower gain table index), and vice verse.
*
* Temperature affects gain differently for different channels:
*
iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG,
priv->ucode_data.len);
- /* Inst bytecount must be last to set up, bit 31 signals uCode
+ /* Inst byte count must be last to set up, bit 31 signals uCode
* that all new ptr/size info is in place */
iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG,
priv->ucode_code.len | BSM_DRAM_INST_LOAD);
}
/*
- * Activate/Deactivat Tx DMA/FIFO channels according tx fifos mask
+ * Activate/Deactivate Tx DMA/FIFO channels according tx fifos mask
* must be called under priv->lock and mac access
*/
static void iwl4965_txq_set_sched(struct iwl_priv *priv, u32 mask)
/* L1 is enabled by BIOS */
if ((link & PCI_CFG_LINK_CTRL_VAL_L1_EN) == PCI_CFG_LINK_CTRL_VAL_L1_EN)
- /* diable L0S disabled L1A enabled */
+ /* disable L0S disabled L1A enabled */
iwl_set_bit(priv, CSR_GIO_REG, CSR_GIO_REG_VAL_L0S_ENABLED);
else
/* L0S enabled L1A disabled */
mutex_lock(&priv->mutex);
- /* Regardless of if we are assocaited, we must reconfigure the
+ /* Regardless of if we are associated, we must reconfigure the
* TX power since frames can be sent on non-radar channels while
* not associated */
iwl4965_send_tx_power(priv);
}
/**
- * iwl4965_tx_status_reply_tx - Handle Tx rspnse for frames in aggregation queue
+ * iwl4965_tx_status_reply_tx - Handle Tx response for frames in aggregation queue
*/
static int iwl4965_tx_status_reply_tx(struct iwl_priv *priv,
struct iwl_ht_agg *agg,
#define IWL50_RTC_INST_SIZE (IWL50_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define IWL50_RTC_DATA_SIZE (IWL50_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
-/* EERPROM */
+/* EEPROM */
#define IWL_5000_EEPROM_IMG_SIZE 2048
#define IWL50_CMD_FIFO_NUM 7
iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS,
CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);
- /* Set FH wait treshold to maximum (HW error during stress W/A) */
+ /* Set FH wait threshold to maximum (HW error during stress W/A) */
iwl_set_bit(priv, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
/* enable HAP INTA to move device L1a -> L0s */
return ret;
}
-/* FIXME: this is indentical to 4965 */
+/* FIXME: this is identical to 4965 */
static void iwl5000_apm_stop(struct iwl_priv *priv)
{
unsigned long flags;
/* L1 is enabled by BIOS */
if ((link & PCI_CFG_LINK_CTRL_VAL_L1_EN) == PCI_CFG_LINK_CTRL_VAL_L1_EN)
- /* diable L0S disabled L1A enabled */
+ /* disable L0S disabled L1A enabled */
iwl_set_bit(priv, CSR_GIO_REG, CSR_GIO_REG_VAL_L0S_ENABLED);
else
/* L0S enabled L1A disabled */
/*
- * Activate/Deactivat Tx DMA/FIFO channels according tx fifos mask
+ * Activate/Deactivate Tx DMA/FIFO channels according tx fifos mask
* must be called under priv->lock and mac access
*/
static void iwl5000_txq_set_sched(struct iwl_priv *priv, u32 mask)
IWL_ERROR("TODO: Implement Tx ABORT REQUIRED!!!\n");
}
-/* Currently 5000 is the supperset of everything */
+/* Currently 5000 is the superset of everything */
static u16 iwl5000_get_hcmd_size(u8 cmd_id, u16 len)
{
return len;
* 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54, 60 MBits
* "G" is the only table that supports CCK (the first 4 rates).
*/
-/*FIXME:RS:need to spearate tables for MIMO2/MIMO3*/
+/*FIXME:RS:need to separate tables for MIMO2/MIMO3*/
static s32 expected_tpt_A[IWL_RATE_COUNT] = {
0, 0, 0, 0, 40, 57, 72, 98, 121, 154, 177, 186, 186
};
lq_sta->active_mimo2_rate,
lq_sta->active_mimo3_rate);
- /* These values will be overriden later */
+ /* These values will be overridden later */
lq_sta->lq.general_params.single_stream_ant_msk = ANT_A;
lq_sta->lq.general_params.dual_stream_ant_msk = ANT_AB;
#define IWL_MIMO2_SWITCH_SISO_C 4
#define IWL_MIMO2_SWITCH_GI 5
-/*FIXME:RS:add posible acctions for MIMO3*/
+/*FIXME:RS:add possible actions for MIMO3*/
#define IWL_ACTION_LIMIT 3 /* # possible actions */
/* call this function to flush any scheduled tasklet */
static inline void iwl_synchronize_irq(struct iwl_priv *priv)
{
- /* wait to make sure we flush pedding tasklet*/
+ /* wait to make sure we flush pending tasklet*/
synchronize_irq(priv->pci_dev->irq);
tasklet_kill(&priv->irq_tasklet);
}
REPLY_TX_POWER_DBM_CMD = 0x98,
MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
- /* Bluetooth device coexistance config command */
+ /* Bluetooth device coexistence config command */
REPLY_BT_CONFIG = 0x9b,
/* Statistics */
u8 cmd; /* Command ID: REPLY_RXON, etc. */
u8 flags; /* 0:5 reserved, 6 abort, 7 internal */
/*
- * The driver sets up the sequence number to values of its chosing.
+ * The driver sets up the sequence number to values of its choosing.
* uCode does not use this value, but passes it back to the driver
* when sending the response to each driver-originated command, so
* the driver can match the response to the command. Since the values
} __attribute__ ((packed));
/**
- * Commad REPLY_TX_POWER_DBM_CMD = 0x98
+ * Command REPLY_TX_POWER_DBM_CMD = 0x98
* struct iwl5000_tx_power_dbm_cmd
*/
#define IWL50_TX_POWER_AUTO 0x7f
* calculating txpower settings:
*
* 1) Power supply voltage indication. The voltage sensor outputs higher
- * values for lower voltage, and vice versa.
+ * values for lower voltage, and vice verse.
*
* 2) Temperature measurement parameters, for each of two channel widths
* (20 MHz and 40 MHz) supported by the radios. Temperature sensing
u8 ofdm_ht_dual_stream_basic_rates;
} __attribute__ ((packed));
-/* 5000 HW just extend this cmmand */
+/* 5000 HW just extend this command */
struct iwl_rxon_cmd {
u8 node_addr[6];
__le16 reserved1;
#define IWL50_OFDM_RSSI_C_BIT_POS 0
struct iwl5000_non_cfg_phy {
- __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* upto 8 phy entries */
+ __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* up to 8 phy entries */
} __attribute__ ((packed));
/* REPLY_TX Tx flags field */
-/* 1: Use RTS/CTS protocol or CTS-to-self if spec alows it
+/* 1: Use RTS/CTS protocol or CTS-to-self if spec allows it
* before this frame. if CTS-to-self required check
* RXON_FLG_SELF_CTS_EN status. */
#define TX_CMD_FLG_RTS_CTS_MSK __constant_cpu_to_le32(1 << 0)
/*
* definitions for initial rate index field
- * bits [3:0] inital rate index
+ * bits [3:0] initial rate index
* bits [6:4] rate table color, used for the initial rate
* bit-7 invalid rate indication
* i.e. rate was not chosen from rate table
* match the modulation characteristics of the history set.
*
* When using block-ack (aggregation), all frames are transmitted at the same
- * rate, since there is no per-attempt acknowledgement from the destination
+ * rate, since there is no per-attempt acknowledgment from the destination
* station. The Tx response struct iwl_tx_resp indicates the Tx rate in
* rate_n_flags field. After receiving a block-ack, the driver can update
* history for the entire block all at once.
*
* 3945 and 4965 support hardware handshake with Bluetooth device on
* same platform. Bluetooth device alerts wireless device when it will Tx;
- * wireless device can delay or kill its own Tx to accomodate.
+ * wireless device can delay or kill its own Tx to accommodate.
*/
struct iwl4965_bt_cmd {
u8 flags;
* '11' Illegal set
*
* NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then
- * ucode assume sleep over DTIM is allowed and we don't need to wakeup
+ * ucode assume sleep over DTIM is allowed and we don't need to wake up
* for every DTIM.
*/
#define IWL_POWER_VEC_SIZE 5
/* COEX flag masks */
-/* Staion table is valid */
+/* Station table is valid */
#define COEX_FLAGS_STA_TABLE_VALID_MSK (0x1)
-/* UnMask wakeup src at unassociated sleep */
+/* UnMask wake up src at unassociated sleep */
#define COEX_FLAGS_UNASSOC_WA_UNMASK_MSK (0x4)
-/* UnMask wakeup src at associated sleep */
+/* UnMask wake up src at associated sleep */
#define COEX_FLAGS_ASSOC_WA_UNMASK_MSK (0x8)
/* Enable CoEx feature. */
#define COEX_FLAGS_COEX_ENABLE_MSK (0x80)
break;
case WLAN_HT_CAP_SM_PS_INVALID:
default:
- IWL_ERROR("invalide mimo ps mode %d\n",
+ IWL_ERROR("invalid mimo ps mode %d\n",
priv->current_ht_config.sm_ps);
WARN_ON(1);
idle_cnt = -1;
};
struct iwl_lib_ops {
- /* set hw dependant perameters */
+ /* set hw dependent parameters */
int (*set_hw_params)(struct iwl_priv *priv);
/* ucode shared memory */
int (*alloc_shared_mem)(struct iwl_priv *priv);
*
* To add your debug level to the list of levels seen when you perform
*
- * % cat /proc/net/iwl/debug_level
+ * % cat /sys/class/net/wlanX/device/debug_level
*
* you simply need to add your entry to the iwl_debug_levels array.
*
- * If you do not see debug_level in /proc/net/iwl then you do not have
- * CONFIG_IWLWIFI_DEBUG defined in your kernel configuration
- *
+ * If you do not see debug_level in /sys/class/net/wlanX/device/debug_level
+ * then you do not have CONFIG_IWLWIFI_DEBUG defined in your kernel config file
*/
#define IWL_DL_INFO (1 << 0)
* @sw_crypto: 0 for hw, 1 for sw
* @max_xxx_size: for ucode uses
* @ct_kill_threshold: temperature threshold
- * @calib_init_cfg: setup initial claibrations for the hw
+ * @calib_init_cfg: setup initial calibrations for the hw
* @struct iwl_sensitivity_ranges: range of sensitivity values
*/
struct iwl_hw_params {
unsigned long status;
- int last_rx_rssi; /* From Rx packet statisitics */
+ int last_rx_rssi; /* From Rx packet statistics */
int last_rx_noise; /* From beacon statistics */
/* counts mgmt, ctl, and data packets */
return 0;
err:
- IWL_ERROR("Unsuported EEPROM VER=0x%x < 0x%x CALIB=0x%x < 0x%x\n",
+ IWL_ERROR("Unsupported EEPROM VER=0x%x < 0x%x CALIB=0x%x < 0x%x\n",
eeprom_ver, priv->cfg->eeprom_ver,
calib_ver, priv->cfg->eeprom_calib_ver);
return -EINVAL;
* _iwl_read32.)
*
* These declarations are *extremely* useful in quickly isolating code deltas
- * which result in misconfiguring of the hardware I/O. In combination with
+ * which result in misconfiguration of the hardware I/O. In combination with
* git-bisect and the IO debug level you can quickly determine the specific
* commit which breaks the IO sequence to the hardware.
*
/* FIXME: + priv->rx_stats[2].bytes; */
s64 tpt = current_tpt - priv->led_tpt;
- if (tpt < 0) /* wrapparound */
+ if (tpt < 0) /* wraparound */
tpt = -tpt;
IWL_DEBUG_LED("tpt %lld current_tpt %llu\n",
#define IWL_REDUCED_POWER_TEMPERATURE 95
/* default power management (not Tx power) table values */
-/* for tim 0-10 */
+/* for TIM 0-10 */
static struct iwl_power_vec_entry range_0[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 2, 2, 0xFF)}, 0},
};
-/* for tim = 3-10 */
+/* for TIM = 3-10 */
static struct iwl_power_vec_entry range_1[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 3, 4, 4)}, 0},
{{SLP, SLP_TOUT(25), SLP_TOUT(25), SLP_VEC(2, 4, 7, 10, 10)}, 2}
};
-/* for tim > 11 */
+/* for TIM > 11 */
static struct iwl_power_vec_entry range_2[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 3, 4, 0xFF)}, 0},
return 0;
}
-/* adjust power command according to dtim period and power level*/
+/* adjust power command according to DTIM period and power level*/
static int iwl_update_power_command(struct iwl_priv *priv,
struct iwl_powertable_cmd *cmd,
u16 mode)
EXPORT_SYMBOL(iwl_power_update_mode);
/* Allow other iwl code to disable/enable power management active
- * this will be usefull for rate scale to disable PM during heavy
+ * this will be useful for rate scale to disable PM during heavy
* Tx/Rx activities
*/
int iwl_power_disable_management(struct iwl_priv *priv, u32 ms)
EXPORT_SYMBOL(iwl_power_disable_management);
/* Allow other iwl code to disable/enable power management active
- * this will be usefull for rate scale to disable PM during hight
- * valume activities
+ * this will be useful for rate scale to disable PM during high
+ * volume activities
*/
int iwl_power_enable_management(struct iwl_priv *priv)
{
}
EXPORT_SYMBOL(iwl_power_set_system_mode);
-/* initilize to default */
+/* initialize to default */
void iwl_power_initialize(struct iwl_priv *priv)
{
mutex_lock(&priv->mutex);
- /* on starting association we disable power managment
+ /* on starting association we disable power management
* until association, if association failed then this
* timer will expire and enable PM again.
*/
*
* 4) Point (via BSM_DRAM_*) to the "runtime" uCode data and instruction
* images in host DRAM. The last register loaded must be the instruction
- * bytecount register ("1" in MSbit tells initialization uCode to load
+ * byte count register ("1" in MSbit tells initialization uCode to load
* the runtime uCode):
- * BSM_DRAM_INST_BYTECOUNT_REG = bytecount | BSM_DRAM_INST_LOAD
+ * BSM_DRAM_INST_BYTECOUNT_REG = byte count | BSM_DRAM_INST_LOAD
*
* 5) Wait for "alive" notification, then issue normal runtime commands.
*
/**
* Tx Scheduler
*
- * The Tx Scheduler selects the next frame to be transmitted, chosing TFDs
+ * The Tx Scheduler selects the next frame to be transmitted, choosing TFDs
* (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
* host DRAM. It steers each frame's Tx command (which contains the frame
* data) into one of up to 7 prioritized Tx DMA FIFO channels within the
iwl_radio_kill_sw_disable_radio(priv);
break;
default:
- IWL_WARNING("we recieved unexpected RFKILL state %d\n", state);
+ IWL_WARNING("we received unexpected RFKILL state %d\n", state);
break;
}
out_unlock:
IWL_DEBUG_RF_KILL("Initializing RFKILL.\n");
priv->rfkill = rfkill_allocate(device, RFKILL_TYPE_WLAN);
if (!priv->rfkill) {
- IWL_ERROR("Unable to allocate rfkill device.\n");
+ IWL_ERROR("Unable to allocate RFKILL device.\n");
ret = -ENOMEM;
goto error;
}
ret = rfkill_register(priv->rfkill);
if (ret) {
- IWL_ERROR("Unable to register rfkill: %d\n", ret);
+ IWL_ERROR("Unable to register RFKILL: %d\n", ret);
goto free_rfkill;
}
}
EXPORT_SYMBOL(iwl_rfkill_unregister);
-/* set rf-kill to the right state. */
+/* set RFKILL to the right state. */
void iwl_rfkill_set_hw_state(struct iwl_priv *priv)
{
if (!priv->rfkill)
(priv->shared_phys + priv->rb_closed_offset) >> 4);
/* Enable Rx DMA
- * FH_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY is set becuase of HW bug in
+ * FH_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY is set because of HW bug in
* the credit mechanism in 5000 HW RX FIFO
* Direct rx interrupts to hosts
* Rx buffer size 4 or 8k
priv->last_rx_noise = IWL_NOISE_MEAS_NOT_AVAILABLE;
/* Set "1" to report good data frames in groups of 100 */
- /* FIXME: need to optimze the call: */
+ /* FIXME: need to optimize the call: */
iwl_dbg_report_frame(priv, pkt, header, 1);
IWL_DEBUG_STATS_LIMIT("Rssi %d, noise %d, qual %d, TSF %llu\n",
* "antenna number"
*
* It seems that the antenna field in the phy flags value
- * is actually a bitfield. This is undefined by radiotap,
+ * is actually a bit field. This is undefined by radiotap,
* it wants an actual antenna number but I always get "7"
* for most legacy frames I receive indicating that the
* same frame was received on all three RX chains.
*
- * I think this field should be removed in favour of a
+ * I think this field should be removed in favor of a
* new 802.11n radiotap field "RX chains" that is defined
* as a bitmask.
*/
goto done;
}
- /* Make sure the scan wasn't cancelled before this queued work
+ /* Make sure the scan wasn't canceled before this queued work
* was given the chance to run... */
if (!test_bit(STATUS_SCANNING, &priv->status))
goto done;
/* else, we are overriding an existing key => no need to allocated room
* in uCode. */
- /* This copy is acutally not needed: we get the key with each TX */
+ /* This copy is actually not needed: we get the key with each TX */
memcpy(priv->stations[sta_id].keyinfo.key, keyconf->key, 16);
memcpy(priv->stations[sta_id].sta.key.key, keyconf->key, 16);
{
int i;
IWL_DEBUG_RATE("lq station id 0x%x\n", lq->sta_id);
- IWL_DEBUG_RATE("lq dta 0x%X 0x%X\n",
+ IWL_DEBUG_RATE("lq ant 0x%X 0x%X\n",
lq->general_params.single_stream_ant_msk,
lq->general_params.dual_stream_ant_msk);
* iwl_rxon_add_station - add station into station table.
*
* there is only one AP station with id= IWL_AP_ID
- * NOTE: mutex must be held before calling this fnction
+ * NOTE: mutex must be held before calling this function
*/
int iwl_rxon_add_station(struct iwl_priv *priv, const u8 *addr, int is_ap)
{
/**
* iwl_txq_ctx_reset - Reset TX queue context
- * Destroys all DMA structures and initialise them again
+ * Destroys all DMA structures and initialize them again
*
* @param priv
* @return error code
memcpy(tx_cmd->key, keyconf->key, keyconf->keylen);
if (info->flags & IEEE80211_TX_CTL_AMPDU)
tx_cmd->tx_flags |= TX_CMD_FLG_AGG_CCMP_MSK;
- IWL_DEBUG_TX("tx_cmd with aes hwcrypto\n");
+ IWL_DEBUG_TX("tx_cmd with AES hwcrypto\n");
break;
case ALG_TKIP:
spin_unlock_irqrestore(&priv->lock, flags);
if (force || iwl3945_is_associated(priv)) {
- IWL_DEBUG_QOS("send QoS cmd with Qos active %d \n",
+ IWL_DEBUG_QOS("send QoS cmd with QoS active %d \n",
priv->qos_data.qos_active);
iwl3945_send_qos_params_command(priv,
/* default power management (not Tx power) table values */
-/* for tim 0-10 */
+/* for TIM 0-10 */
static struct iwl3945_power_vec_entry range_0[IWL_POWER_AC] = {
{{NOSLP, SLP_TIMEOUT(0), SLP_TIMEOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(500), SLP_VEC(1, 2, 3, 4, 4)}, 0},
{{SLP, SLP_TIMEOUT(25), SLP_TIMEOUT(25), SLP_VEC(4, 7, 10, 10, 10)}, 1}
};
-/* for tim > 10 */
+/* for TIM > 10 */
static struct iwl3945_power_vec_entry range_1[IWL_POWER_AC] = {
{{NOSLP, SLP_TIMEOUT(0), SLP_TIMEOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TIMEOUT(200), SLP_TIMEOUT(500),
iwl3945_clear_stations_table(priv);
- /* dont commit rxon if rf-kill is on*/
+ /* don't commit rxon if rf-kill is on*/
if (!iwl3945_is_ready_rf(priv))
return -EAGAIN;
case ALG_CCMP:
cmd->cmd.tx.sec_ctl = TX_CMD_SEC_CCM;
memcpy(cmd->cmd.tx.key, keyinfo->key, keyinfo->keylen);
- IWL_DEBUG_TX("tx_cmd with aes hwcrypto\n");
+ IWL_DEBUG_TX("tx_cmd with AES hwcrypto\n");
break;
case ALG_TKIP:
/* call this function to flush any scheduled tasklet */
static inline void iwl_synchronize_irq(struct iwl3945_priv *priv)
{
- /* wait to make sure we flush pedding tasklet*/
+ /* wait to make sure we flush pending tasklet*/
synchronize_irq(priv->pci_dev->irq);
tasklet_kill(&priv->irq_tasklet);
}
iwl3945_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG,
priv->ucode_data.len);
- /* Inst bytecount must be last to set up, bit 31 signals uCode
+ /* Inst byte count must be last to set up, bit 31 signals uCode
* that all new ptr/size info is in place */
iwl3945_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG,
priv->ucode_code.len | BSM_DRAM_INST_LOAD);
rc = iwl3945_grab_nic_access(priv);
if (rc) {
- IWL_WARNING("Can not read rfkill status from adapter\n");
+ IWL_WARNING("Can not read RFKILL status from adapter\n");
return;
}
if (rfkill & 0x1) {
clear_bit(STATUS_RF_KILL_HW, &priv->status);
- /* if rfkill is not on, then wait for thermal
+ /* if RFKILL is not on, then wait for thermal
* sensor in adapter to kick in */
while (iwl3945_hw_get_temperature(priv) == 0) {
thermal_spin++;
}
if (!priv->ucode_data_backup.v_addr || !priv->ucode_data.v_addr) {
- IWL_ERROR("ucode not available for device bringup\n");
+ IWL_ERROR("ucode not available for device bring up\n");
return -EIO;
}
goto done;
}
- /* Make sure the scan wasn't cancelled before this queued work
+ /* Make sure the scan wasn't canceled before this queued work
* was given the chance to run... */
if (!test_bit(STATUS_SCANNING, &priv->status))
goto done;
/*****************************************************************************
*
- * driver setup and teardown
+ * driver setup and tear down
*
*****************************************************************************/
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return 0;
- IWL_DEBUG_RF_KILL("we recieved soft RFKILL set to state %d\n", state);
+ IWL_DEBUG_RF_KILL("we received soft RFKILL set to state %d\n", state);
mutex_lock(&priv->mutex);
switch (state) {
iwl3945_radio_kill_sw(priv, 1);
break;
default:
- IWL_WARNING("we recieved unexpected RFKILL state %d\n", state);
+ IWL_WARNING("we received unexpected RFKILL state %d\n", state);
break;
}
out_unlock:
projects / GitHub / mt8127 / android_kernel_alcatel_ttab.git / commitdiff