/*
* Miscellaneous IOCTL commands for Dynamic Power Management Controller Driver
*
- * Copyright (C) 2004-2008 Analog Device Inc.
+ * Copyright (C) 2004-2009 Analog Device Inc.
*
* Licensed under the GPL-2
*/
#ifndef _BLACKFIN_DPMC_H_
#define _BLACKFIN_DPMC_H_
-#ifdef __KERNEL__
+/* PLL_CTL Masks */
+#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
+#define PLL_OFF 0x0002 /* PLL Not Powered */
+#define STOPCK 0x0008 /* Core Clock Off */
+#define PDWN 0x0020 /* Enter Deep Sleep Mode */
+#ifdef __ADSPBF539__
+# define IN_DELAY 0x0014 /* Add 200ps Delay To EBIU Input Latches */
+# define OUT_DELAY 0x00C0 /* Add 200ps Delay To EBIU Output Signals */
+#else
+# define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
+# define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
+#endif
+#define BYPASS 0x0100 /* Bypass the PLL */
+#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
+#define SPORT_HYST 0x8000 /* Enable Additional Hysteresis on SPORT Input Pins */
+#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
+
+/* PLL_DIV Masks */
+#define SSEL 0x000F /* System Select */
+#define CSEL 0x0030 /* Core Select */
+#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
+#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
+#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
+#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
+
+#define CCLK_DIV1 CSEL_DIV1
+#define CCLK_DIV2 CSEL_DIV2
+#define CCLK_DIV4 CSEL_DIV4
+#define CCLK_DIV8 CSEL_DIV8
+
+#define SET_SSEL(x) ((x) & 0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
+#define SCLK_DIV(x) (x) /* SCLK = VCO / x */
+
+/* PLL_STAT Masks */
+#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
+#define FULL_ON 0x0002 /* Processor In Full On Mode */
+#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
+#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
+
+#define RTCWS 0x0400 /* RTC/Reset Wake-Up Status */
+#define CANWS 0x0800 /* CAN Wake-Up Status */
+#define USBWS 0x2000 /* USB Wake-Up Status */
+#define KPADWS 0x4000 /* Keypad Wake-Up Status */
+#define ROTWS 0x8000 /* Rotary Wake-Up Status */
+#define GPWS 0x1000 /* General-Purpose Wake-Up Status */
+
+/* VR_CTL Masks */
+#if defined(__ADSPBF52x__) || defined(__ADSPBF51x__)
+#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */
+#define FREQ_1000 0x3000 /* Switching Frequency Is 1 MHz */
+#else
+#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
+#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
+#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
+#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
+#endif
+#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
+
+#define GAIN 0x000C /* Voltage Level Gain */
+#define GAIN_5 0x0000 /* GAIN = 5 */
+#define GAIN_10 0x0004 /* GAIN = 1 */
+#define GAIN_20 0x0008 /* GAIN = 2 */
+#define GAIN_50 0x000C /* GAIN = 5 */
+
+#define VLEV 0x00F0 /* Internal Voltage Level */
+#ifdef __ADSPBF52x__
+#define VLEV_085 0x0040 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
+#define VLEV_090 0x0050 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
+#define VLEV_095 0x0060 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
+#define VLEV_100 0x0070 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
+#define VLEV_105 0x0080 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
+#define VLEV_110 0x0090 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
+#define VLEV_115 0x00A0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
+#define VLEV_120 0x00B0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
+#else
+#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
+#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
+#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
+#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
+#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
+#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
+#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
+#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
+#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
+#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
+#endif
+
+#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
+#define CANWE 0x0200 /* Enable CAN Wakeup From Hibernate */
+#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */
+#define GPWE 0x0400 /* General-Purpose Wake-Up Enable */
+#define MXVRWE 0x0400 /* Enable MXVR Wakeup From Hibernate */
+#define KPADWE 0x1000 /* Keypad Wake-Up Enable */
+#define ROTWE 0x2000 /* Rotary Wake-Up Enable */
+#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */
+#define SCKELOW 0x8000 /* Do Not Drive SCKE High During Reset After Hibernate */
+
+#if defined(__ADSPBF52x__) || defined(__ADSPBF51x__)
+#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */
+#else
+#define USBWE 0x0800 /* Enable USB Wakeup From Hibernate */
+#endif
+
#ifndef __ASSEMBLY__
void sleep_mode(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2);
w[P0 + (x - PLL_CTL)] = R0;\
#endif
-#endif /* __KERNEL__ */
#endif /*_BLACKFIN_DPMC_H_*/
#define OFFSET_SCR 0x1C /* SCR Scratch Register */
#define OFFSET_GCTL 0x24 /* Global Control Register */
-/* PLL_DIV Masks */
-#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */
-
#endif
** modifier UNLESS the lower order bits are saved and ORed back in when
** the macro is used.
*************************************************************************************/
-/*
-** ********************* PLL AND RESET MASKS ****************************************/
-/* PLL_CTL Masks */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* PLL Not Powered */
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Enter Deep Sleep Mode */
-#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
-#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
-#define BYPASS 0x0100 /* Bypass the PLL */
-#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
-/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-/* PLL_DIV Macros */
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-
-/* VR_CTL Masks */
-#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */
-#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */
-#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */
-#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */
-#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
#define OFFSET_SCR 0x1C /* SCR Scratch Register */
#define OFFSET_GCTL 0x24 /* Global Control Register */
-/* PLL_DIV Masks */
-#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */
-
#endif
** modifier UNLESS the lower order bits are saved and ORed back in when
** the macro is used.
*************************************************************************************/
-/*
-** ********************* PLL AND RESET MASKS ****************************************/
-/* PLL_CTL Masks */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* PLL Not Powered */
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Enter Deep Sleep Mode */
-#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
-#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
-#define BYPASS 0x0100 /* Bypass the PLL */
-#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
-/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-/* PLL_DIV Macros */
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-
-/* VR_CTL Masks */
-#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */
-#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */
-#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */
-#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */
-#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
/* System MMR Register Bits */
/******************************************************************************* */
-/* ********************* PLL AND RESET MASKS ************************ */
-
-/* PLL_CTL Masks */
-#define PLL_CLKIN 0x0000 /* Pass CLKIN to PLL */
-#define PLL_CLKIN_DIV2 0x0001 /* Pass CLKIN/2 to PLL */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* Shut off PLL clocks */
-#define STOPCK_OFF 0x0008 /* Core clock off */
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Put the PLL in a Deep Sleep state */
-#if !defined(__ADSPBF538__)
-/* this file is included in defBF538.h but IN_DELAY/OUT_DELAY are different */
-# define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
-# define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
-#endif
-#define BYPASS 0x0100 /* Bypass the PLL */
-/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-
-#define SCLK_DIV(x) (x) /* SCLK = VCO / x */
-
-#define CCLK_DIV1 0x00000000 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 0x00000010 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 0x00000020 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 0x00000030 /* CCLK = VCO / 8 */
-/* PLL_DIV Macros */
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
-
-/* VR_CTL Masks */
-#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
-#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
-#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
-
-#define GAIN 0x000C /* Voltage Level Gain */
-#define GAIN_5 0x0000 /* GAIN = 5 */
-#define GAIN_10 0x0004 /* GAIN = 10 */
-#define GAIN_20 0x0008 /* GAIN = 20 */
-#define GAIN_50 0x000C /* GAIN = 50 */
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define SCKELOW 0x8000 /* Do Not Drive SCKE High During Reset After Hibernate */
-
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
#define CHIPID_FAMILY 0x0FFFF000
#define OFFSET_SCR 0x1C /* SCR Scratch Register */
#define OFFSET_GCTL 0x24 /* Global Control Register */
-/* PLL_DIV Masks */
-#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */
-
#endif
** modifier UNLESS the lower order bits are saved and ORed back in when
** the macro is used.
*************************************************************************************/
-/*
-** ********************* PLL AND RESET MASKS ****************************************/
-/* PLL_CTL Masks */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* PLL Not Powered */
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Enter Deep Sleep Mode */
-#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
-#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
-#define BYPASS 0x0100 /* Bypass the PLL */
-#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
-/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-/* PLL_DIV Macros */
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-
-/* VR_CTL Masks */
-#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
-#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
-#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
-
-#define GAIN 0x000C /* Voltage Level Gain */
-#define GAIN_5 0x0000 /* GAIN = 5 */
-#define GAIN_10 0x0004 /* GAIN = 10 */
-#define GAIN_20 0x0008 /* GAIN = 20 */
-#define GAIN_50 0x000C /* GAIN = 50 */
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define CANWE 0x0200 /* Enable CAN Wakeup From Hibernate */
-#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */
-#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */
-#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */
-#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
#define OFFSET_SCR 0x1C /* SCR Scratch Register */
#define OFFSET_GCTL 0x24 /* Global Control Register */
-/* PLL_DIV Masks */
-#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */
-
#endif
/* System MMR Register Bits and Macros */
/******************************************************************************* */
-/* ********************* PLL AND RESET MASKS ************************ */
-/* PLL_CTL Masks */
-#define PLL_CLKIN 0x0000 /* Pass CLKIN to PLL */
-#define PLL_CLKIN_DIV2 0x0001 /* Pass CLKIN/2 to PLL */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* Shut off PLL clocks */
-
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Put the PLL in a Deep Sleep state */
-#define IN_DELAY 0x0014 /* EBIU Input Delay Select */
-#define OUT_DELAY 0x00C0 /* EBIU Output Delay Select */
-#define BYPASS 0x0100 /* Bypass the PLL */
-#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
-
-/* PLL_CTL Macros */
-#ifdef _MISRA_RULES
-#define SET_MSEL(x) (((x)&0x3Fu) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-#define SET_OUT_DELAY(x) (((x)&0x03u) << 0x6)
-#define SET_IN_DELAY(x) ((((x)&0x02u) << 0x3) | (((x)&0x01u) << 0x2))
-#else
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-#define SET_OUT_DELAY(x) (((x)&0x03) << 0x6)
-#define SET_IN_DELAY(x) ((((x)&0x02) << 0x3) | (((x)&0x01) << 0x2))
-#endif /* _MISRA_RULES */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-
-#define SCLK_DIV(x) (x) /* SCLK = VCO / x */
-
-/* PLL_DIV Macros */
-#ifdef _MISRA_RULES
-#define SET_SSEL(x) ((x)&0xFu) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-#else
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-#endif /* _MISRA_RULES */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
-
-/* VR_CTL Masks */
-#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
-#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
-#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
-
-#define GAIN 0x000C /* Voltage Level Gain */
-#define GAIN_5 0x0000 /* GAIN = 5 */
-#define GAIN_10 0x0004 /* GAIN = 10 */
-#define GAIN_20 0x0008 /* GAIN = 20 */
-#define GAIN_50 0x000C /* GAIN = 50 */
-
-#define VLEV 0x00F0 /* Internal Voltage Level - Only Program Values Within Specifications */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (See Datasheet for Regulator Tolerance) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (See Datasheet for Regulator Tolerance) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define CANWE 0x0200 /* Enable CAN Wakeup From Hibernate */
-#define MXVRWE 0x0400 /* Enable MXVR Wakeup From Hibernate */
-#define SCKELOW 0x8000 /* Do Not Drive SCKE High During Reset After Hibernate */
-
/* SWRST Mask */
#define SYSTEM_RESET 0x0007 /* Initiates A System Software Reset */
#define DOUBLE_FAULT 0x0008 /* Core Double Fault Causes Reset */
#define OFFSET_THR 0x28 /* Transmit Holding register */
#define OFFSET_RBR 0x2C /* Receive Buffer register */
-/* PLL_DIV Masks */
-#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */
-
#endif
#define AFEXIT 0x10 /* Authentication Firmware Exit */
#define SECSTAT 0xe0 /* Secure Status */
-/* Bit masks for PLL_DIV */
-
-#define CSEL 0x30 /* Core Select */
-#define SSEL 0xf /* System Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-
-/* Bit masks for PLL_CTL */
-
-#define MSEL 0x7e00 /* Multiplier Select */
-#define BYPASS 0x100 /* PLL Bypass Enable */
-#define OUTPUT_DELAY 0x80 /* External Memory Output Delay Enable */
-#define INPUT_DELAY 0x40 /* External Memory Input Delay Enable */
-#define PDWN 0x20 /* Power Down */
-#define STOPCK 0x8 /* Stop Clock */
-#define PLL_OFF 0x2 /* Disable PLL */
-#define DF 0x1 /* Divide Frequency */
-
/* SWRST Masks */
#define SYSTEM_RESET 0x0007 /* Initiates A System Software Reset */
#define DOUBLE_FAULT 0x0008 /* Core Double Fault Causes Reset */
#define RESET_WDOG 0x4000 /* SW Reset Generated By Watchdog Timer */
#define RESET_SOFTWARE 0x8000 /* SW Reset Occurred Since Last Read Of SWRST */
-/* Bit masks for PLL_STAT */
-
-#define PLL_LOCKED 0x20 /* PLL Locked Status */
-#define ACTIVE_PLLDISABLED 0x4 /* Active Mode With PLL Disabled */
-#define FULL_ON 0x2 /* Full-On Mode */
-#define ACTIVE_PLLENABLED 0x1 /* Active Mode With PLL Enabled */
-#define RTCWS 0x400 /* RTC/Reset Wake-Up Status */
-#define CANWS 0x800 /* CAN Wake-Up Status */
-#define USBWS 0x2000 /* USB Wake-Up Status */
-#define KPADWS 0x4000 /* Keypad Wake-Up Status */
-#define ROTWS 0x8000 /* Rotary Wake-Up Status */
-#define GPWS 0x1000 /* General-Purpose Wake-Up Status */
-
-/* Bit masks for VR_CTL */
-
-#define FREQ 0x3 /* Regulator Switching Frequency */
-#define GAIN 0xc /* Voltage Output Level Gain */
-#define VLEV 0xf0 /* Internal Voltage Level */
-#define SCKELOW 0x8000 /* Drive SCKE Low During Reset Enable */
-#define WAKE 0x100 /* RTC/Reset Wake-Up Enable */
-#define CANWE 0x200 /* CAN0/1 Wake-Up Enable */
-#define GPWE 0x400 /* General-Purpose Wake-Up Enable */
-#define USBWE 0x800 /* USB Wake-Up Enable */
-#define KPADWE 0x1000 /* Keypad Wake-Up Enable */
-#define ROTWE 0x2000 /* Rotary Wake-Up Enable */
-
-#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
-#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
-#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
-
-#define GAIN_5 0x0000 /* GAIN = 5*/
-#define GAIN_10 0x0004 /* GAIN = 1*/
-#define GAIN_20 0x0008 /* GAIN = 2*/
-#define GAIN_50 0x000C /* GAIN = 5*/
-
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
/* Bit masks for NFC_CTL */
#define WR_DLY 0xf /* Write Strobe Delay */
/* System MMR Register Bits */
/******************************************************************************* */
-/* ********************* PLL AND RESET MASKS ************************ */
-
-/* PLL_CTL Masks */
-#define PLL_CLKIN 0x00000000 /* Pass CLKIN to PLL */
-#define PLL_CLKIN_DIV2 0x00000001 /* Pass CLKIN/2 to PLL */
-#define PLL_OFF 0x00000002 /* Shut off PLL clocks */
-#define STOPCK_OFF 0x00000008 /* Core clock off */
-#define PDWN 0x00000020 /* Put the PLL in a Deep Sleep state */
-#define BYPASS 0x00000100 /* Bypass the PLL */
-
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
#define CHIPID_FAMILY 0x0FFFF000
#define CHIPID_MANUFACTURE 0x00000FFE
-/* VR_CTL Masks */
-#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
-#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
-#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
-
-#define GAIN 0x000C /* Voltage Level Gain */
-#define GAIN_5 0x0000 /* GAIN = 5*/
-#define GAIN_10 0x0004 /* GAIN = 1*/
-#define GAIN_20 0x0008 /* GAIN = 2*/
-#define GAIN_50 0x000C /* GAIN = 5*/
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define SCKELOW 0x8000 /* Do Not Drive SCKE High During Reset After Hibernate */
-
-/* PLL_DIV Masks */
-#define SCLK_DIV(x) (x) /* SCLK = VCO / x */
-
-#define CSEL 0x30 /* Core Select */
-#define SSEL 0xf /* System Select */
-#define CCLK_DIV1 0x00000000 /* CCLK = VCO / 1 */
-#define CCLK_DIV2 0x00000010 /* CCLK = VCO / 2 */
-#define CCLK_DIV4 0x00000020 /* CCLK = VCO / 4 */
-#define CCLK_DIV8 0x00000030 /* CCLK = VCO / 8 */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
-
/* SICA_SYSCR Masks */
#define COREB_SRAM_INIT 0x0020
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff