ixgbe: fix for link failure on SFP+ DA cables
authorDon Skidmore <donald.c.skidmore@intel.com>
Fri, 3 Dec 2010 13:23:30 +0000 (13:23 +0000)
committerDavid S. Miller <davem@davemloft.net>
Mon, 6 Dec 2010 21:18:50 +0000 (13:18 -0800)
This patch helps prevent FW/SW semaphore collision from leading
to link establishment failure.  The collision might mess up the
PHY registers so we reset the PHY.  However there are SFI/KR areas
in the PHY that are not reset with a Reset_AN so we need to change
LMS to reset it.  Also wait until AN state machine is AN_GOOD

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ixgbe/ixgbe_82599.c
drivers/net/ixgbe/ixgbe_type.h

index 385ccebb826cbe65e5216a5ecc83674844140369..6827dddc383e0f99334f9e76b131695ba6a58773 100644 (file)
@@ -96,6 +96,8 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)
 static s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw)
 {
        s32 ret_val = 0;
+       u32 reg_anlp1 = 0;
+       u32 i = 0;
        u16 list_offset, data_offset, data_value;
 
        if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) {
@@ -122,14 +124,34 @@ static s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw)
                        IXGBE_WRITE_FLUSH(hw);
                        hw->eeprom.ops.read(hw, ++data_offset, &data_value);
                }
-               /* Now restart DSP by setting Restart_AN */
-               IXGBE_WRITE_REG(hw, IXGBE_AUTOC,
-                   (IXGBE_READ_REG(hw, IXGBE_AUTOC) | IXGBE_AUTOC_AN_RESTART));
 
                /* Release the semaphore */
                ixgbe_release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
                /* Delay obtaining semaphore again to allow FW access */
                msleep(hw->eeprom.semaphore_delay);
+
+               /* Now restart DSP by setting Restart_AN and clearing LMS */
+               IXGBE_WRITE_REG(hw, IXGBE_AUTOC, ((IXGBE_READ_REG(hw,
+                               IXGBE_AUTOC) & ~IXGBE_AUTOC_LMS_MASK) |
+                               IXGBE_AUTOC_AN_RESTART));
+
+               /* Wait for AN to leave state 0 */
+               for (i = 0; i < 10; i++) {
+                       msleep(4);
+                       reg_anlp1 = IXGBE_READ_REG(hw, IXGBE_ANLP1);
+                       if (reg_anlp1 & IXGBE_ANLP1_AN_STATE_MASK)
+                               break;
+               }
+               if (!(reg_anlp1 & IXGBE_ANLP1_AN_STATE_MASK)) {
+                       hw_dbg(hw, "sfp module setup not complete\n");
+                       ret_val = IXGBE_ERR_SFP_SETUP_NOT_COMPLETE;
+                       goto setup_sfp_out;
+               }
+
+               /* Restart DSP by setting Restart_AN and return to SFI mode */
+               IXGBE_WRITE_REG(hw, IXGBE_AUTOC, (IXGBE_READ_REG(hw,
+                               IXGBE_AUTOC) | IXGBE_AUTOC_LMS_10G_SERIAL |
+                               IXGBE_AUTOC_AN_RESTART));
        }
 
 setup_sfp_out:
index ef816dd5a8f01ac9356d1f10d4aa3ddbc57cae28..0f80893edabf67326b3b574a2e3f517744d8bae7 100644 (file)
 #define IXGBE_ANLP1_PAUSE               0x0C00
 #define IXGBE_ANLP1_SYM_PAUSE           0x0400
 #define IXGBE_ANLP1_ASM_PAUSE           0x0800
+#define IXGBE_ANLP1_AN_STATE_MASK       0x000f0000
+
 
 /* SW Semaphore Register bitmasks */
 #define IXGBE_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
@@ -2641,6 +2643,7 @@ struct ixgbe_info {
 #define IXGBE_ERR_NO_SPACE                      -25
 #define IXGBE_ERR_OVERTEMP                      -26
 #define IXGBE_ERR_RAR_INDEX                     -27
+#define IXGBE_ERR_SFP_SETUP_NOT_COMPLETE        -30
 #define IXGBE_ERR_PBA_SECTION                   -31
 #define IXGBE_ERR_INVALID_ARGUMENT              -32
 #define IXGBE_NOT_IMPLEMENTED                   0x7FFFFFFF