#include "rtl8187.h"
#include "rtl8187_rtl8225.h"
+#ifdef CONFIG_RTL8187_LEDS
+#include "rtl8187_leds.h"
+#endif
MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
MODULE_AUTHOR("Andrea Merello <andreamrl@tiscali.it>");
{0x85, 0x24, 0}, {0x88, 0x54, 0}, {0x8B, 0xB8, 0}, {0x8C, 0x07, 0},
{0x8D, 0x00, 0}, {0x94, 0x1B, 0}, {0x95, 0x12, 0}, {0x96, 0x00, 0},
{0x97, 0x06, 0}, {0x9D, 0x1A, 0}, {0x9F, 0x10, 0}, {0xB4, 0x22, 0},
- {0xBE, 0x80, 0}, {0xDB, 0x00, 0}, {0xEE, 0x00, 0}, {0x91, 0x03, 0},
+ {0xBE, 0x80, 0}, {0xDB, 0x00, 0}, {0xEE, 0x00, 0}, {0x4C, 0x00, 2},
- {0x4C, 0x00, 2}, {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0},
- {0x8E, 0x08, 0}, {0x8F, 0x00, 0}
+ {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0},
+ {0x8F, 0x00, 0}
};
static int rtl8187b_init_hw(struct ieee80211_hw *dev)
wiphy_name(dev->wiphy), dev->wiphy->perm_addr,
chip_name, priv->asic_rev, priv->rf->name);
+#ifdef CONFIG_RTL8187_LEDS
+ eeprom_93cx6_read(&eeprom, 0x3F, ®);
+ reg &= 0xFF;
+ rtl8187_leds_init(dev, reg);
+#endif
+
return 0;
err_free_dev:
if (!dev)
return;
+#ifdef CONFIG_RTL8187_LEDS
+ rtl8187_leds_exit(dev);
+#endif
ieee80211_unregister_hw(dev);
priv = dev->priv;
--- /dev/null
+/*
+ * Linux LED driver for RTL8187
+ *
+ * Copyright 2009 Larry Finger <Larry.Finger@lwfinger.net>
+ *
+ * Based on the LED handling in the r8187 driver, which is:
+ * Copyright (c) Realtek Semiconductor Corp. All rights reserved.
+ *
+ * Thanks to Realtek for their support!
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifdef CONFIG_RTL8187_LEDS
+
+#include <net/mac80211.h>
+#include <linux/usb.h>
+#include <linux/eeprom_93cx6.h>
+
+#include "rtl8187.h"
+#include "rtl8187_leds.h"
+
+static void led_turn_on(struct work_struct *work)
+{
+ /* As this routine does read/write operations on the hardware, it must
+ * be run from a work queue.
+ */
+ u8 reg;
+ struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
+ led_on.work);
+ struct rtl8187_led *led = &priv->led_tx;
+
+ /* Don't change the LED, when the device is down. */
+ if (priv->mode == NL80211_IFTYPE_UNSPECIFIED)
+ return ;
+
+ /* Skip if the LED is not registered. */
+ if (!led->dev)
+ return;
+ mutex_lock(&priv->conf_mutex);
+ switch (led->ledpin) {
+ case LED_PIN_GPIO0:
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 0x01);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0x00);
+ break;
+ case LED_PIN_LED0:
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~(1 << 4);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
+ break;
+ case LED_PIN_LED1:
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~(1 << 5);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
+ break;
+ case LED_PIN_HW:
+ default:
+ break;
+ }
+ mutex_unlock(&priv->conf_mutex);
+}
+
+static void led_turn_off(struct work_struct *work)
+{
+ /* As this routine does read/write operations on the hardware, it must
+ * be run from a work queue.
+ */
+ u8 reg;
+ struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
+ led_off.work);
+ struct rtl8187_led *led = &priv->led_tx;
+
+ /* Don't change the LED, when the device is down. */
+ if (priv->mode == NL80211_IFTYPE_UNSPECIFIED)
+ return ;
+
+ /* Skip if the LED is not registered. */
+ if (!led->dev)
+ return;
+ mutex_lock(&priv->conf_mutex);
+ switch (led->ledpin) {
+ case LED_PIN_GPIO0:
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 0x01);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0x01);
+ break;
+ case LED_PIN_LED0:
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) | (1 << 4);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
+ break;
+ case LED_PIN_LED1:
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) | (1 << 5);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
+ break;
+ case LED_PIN_HW:
+ default:
+ break;
+ }
+ mutex_unlock(&priv->conf_mutex);
+}
+
+/* Callback from the LED subsystem. */
+static void rtl8187_led_brightness_set(struct led_classdev *led_dev,
+ enum led_brightness brightness)
+{
+ struct rtl8187_led *led = container_of(led_dev, struct rtl8187_led,
+ led_dev);
+ struct ieee80211_hw *hw = led->dev;
+ struct rtl8187_priv *priv = hw->priv;
+
+ if (brightness == LED_OFF) {
+ queue_delayed_work(hw->workqueue, &priv->led_off, 0);
+ /* The LED is off for 1/20 sec so that it just blinks. */
+ queue_delayed_work(hw->workqueue, &priv->led_on, HZ / 20);
+ } else
+ queue_delayed_work(hw->workqueue, &priv->led_on, 0);
+}
+
+static int rtl8187_register_led(struct ieee80211_hw *dev,
+ struct rtl8187_led *led, const char *name,
+ const char *default_trigger, u8 ledpin)
+{
+ int err;
+ struct rtl8187_priv *priv = dev->priv;
+
+ if (led->dev)
+ return -EEXIST;
+ if (!default_trigger)
+ return -EINVAL;
+ led->dev = dev;
+ led->ledpin = ledpin;
+ strncpy(led->name, name, sizeof(led->name));
+
+ led->led_dev.name = led->name;
+ led->led_dev.default_trigger = default_trigger;
+ led->led_dev.brightness_set = rtl8187_led_brightness_set;
+
+ err = led_classdev_register(&priv->udev->dev, &led->led_dev);
+ if (err) {
+ printk(KERN_INFO "LEDs: Failed to register %s\n", name);
+ led->dev = NULL;
+ return err;
+ }
+ return 0;
+}
+
+static void rtl8187_unregister_led(struct rtl8187_led *led)
+{
+ led_classdev_unregister(&led->led_dev);
+ led->dev = NULL;
+}
+
+void rtl8187_leds_init(struct ieee80211_hw *dev, u16 custid)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ char name[RTL8187_LED_MAX_NAME_LEN + 1];
+ u8 ledpin;
+ int err;
+
+ /* According to the vendor driver, the LED operation depends on the
+ * customer ID encoded in the EEPROM
+ */
+ printk(KERN_INFO "rtl8187: Customer ID is 0x%02X\n", custid);
+ switch (custid) {
+ case EEPROM_CID_RSVD0:
+ case EEPROM_CID_RSVD1:
+ case EEPROM_CID_SERCOMM_PS:
+ case EEPROM_CID_QMI:
+ case EEPROM_CID_DELL:
+ case EEPROM_CID_TOSHIBA:
+ ledpin = LED_PIN_GPIO0;
+ break;
+ case EEPROM_CID_ALPHA0:
+ ledpin = LED_PIN_LED0;
+ break;
+ case EEPROM_CID_HW:
+ ledpin = LED_PIN_HW;
+ break;
+ default:
+ ledpin = LED_PIN_GPIO0;
+ }
+
+ INIT_DELAYED_WORK(&priv->led_on, led_turn_on);
+ INIT_DELAYED_WORK(&priv->led_off, led_turn_off);
+
+ snprintf(name, sizeof(name),
+ "rtl8187-%s::tx", wiphy_name(dev->wiphy));
+ err = rtl8187_register_led(dev, &priv->led_tx, name,
+ ieee80211_get_tx_led_name(dev), ledpin);
+ if (err)
+ goto error;
+ snprintf(name, sizeof(name),
+ "rtl8187-%s::rx", wiphy_name(dev->wiphy));
+ err = rtl8187_register_led(dev, &priv->led_rx, name,
+ ieee80211_get_rx_led_name(dev), ledpin);
+ if (!err) {
+ queue_delayed_work(dev->workqueue, &priv->led_on, 0);
+ return;
+ }
+ /* registration of RX LED failed - unregister TX */
+ rtl8187_unregister_led(&priv->led_tx);
+error:
+ /* If registration of either failed, cancel delayed work */
+ cancel_delayed_work_sync(&priv->led_off);
+ cancel_delayed_work_sync(&priv->led_on);
+}
+
+void rtl8187_leds_exit(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+
+ rtl8187_unregister_led(&priv->led_tx);
+ /* turn the LED off before exiting */
+ queue_delayed_work(dev->workqueue, &priv->led_off, 0);
+ cancel_delayed_work_sync(&priv->led_off);
+ rtl8187_unregister_led(&priv->led_rx);
+}
+#endif /* def CONFIG_RTL8187_LED */
+
--- /dev/null
+/*
+ * Definitions for RTL8187 leds
+ *
+ * Copyright 2009 Larry Finger <Larry.Finger@lwfinger.net>
+ *
+ * Based on the LED handling in the r8187 driver, which is:
+ * Copyright (c) Realtek Semiconductor Corp. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef RTL8187_LED_H
+#define RTL8187_LED_H
+
+#ifdef CONFIG_RTL8187_LEDS
+
+#define RTL8187_LED_MAX_NAME_LEN 21
+
+#include <linux/leds.h>
+#include <linux/types.h>
+
+enum {
+ LED_PIN_LED0,
+ LED_PIN_LED1,
+ LED_PIN_GPIO0,
+ LED_PIN_HW
+};
+
+enum {
+ EEPROM_CID_RSVD0 = 0x00,
+ EEPROM_CID_RSVD1 = 0xFF,
+ EEPROM_CID_ALPHA0 = 0x01,
+ EEPROM_CID_SERCOMM_PS = 0x02,
+ EEPROM_CID_HW = 0x03,
+ EEPROM_CID_TOSHIBA = 0x04,
+ EEPROM_CID_QMI = 0x07,
+ EEPROM_CID_DELL = 0x08
+};
+
+struct rtl8187_led {
+ struct ieee80211_hw *dev;
+ /* The LED class device */
+ struct led_classdev led_dev;
+ /* The pin/method used to control the led */
+ u8 ledpin;
+ /* The unique name string for this LED device. */
+ char name[RTL8187_LED_MAX_NAME_LEN + 1];
+};
+
+void rtl8187_leds_init(struct ieee80211_hw *dev, u16 code);
+void rtl8187_leds_exit(struct ieee80211_hw *dev);
+
+#endif /* def CONFIG_RTL8187_LED */
+
+#endif /* RTL8187_LED_H */
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / commitdiff