pdev->io.NumPorts2 = (stk->is_kme) ? 2 : 1;
if (pcmcia_request_io(pdev, &pdev->io) != 0)
return -ENODEV;
- stk->ctl_base = pdev->io.BasePort2;
+ stk->ctl_base = pdev->resource[1]->start;
} else if ((io->nwin == 1) && (io->win[0].len >= 16)) {
pdev->io.NumPorts1 = io->win[0].len;
pdev->io.NumPorts2 = 0;
if (pcmcia_request_io(pdev, &pdev->io) != 0)
return -ENODEV;
- stk->ctl_base = pdev->io.BasePort1 + 0x0e;
+ stk->ctl_base = pdev->resource[0]->start + 0x0e;
} else
return -ENODEV;
/* If we've got this far, we're done */
if (pcmcia_loop_config(pdev, pcmcia_check_one_config, stk))
goto failed; /* No suitable config found */
}
- io_base = pdev->io.BasePort1;
+ io_base = pdev->resource[0]->start;
ctl_base = stk->ctl_base;
if (!pdev->irq)
goto failed;
/* FIXME: Could be more ports at base + 0x10 but we only deal with
one right now */
- if (pdev->io.NumPorts1 >= 0x20)
+ if (resource_size(pdev->resource[0]) >= 0x20)
n_ports = 2;
if (pdev->manf_id == 0x0097 && pdev->card_id == 0x1620)
static void bluecard_activity_led_timeout(u_long arg)
{
bluecard_info_t *info = (bluecard_info_t *)arg;
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
if (!test_bit(CARD_HAS_PCCARD_ID, &(info->hw_state)))
return;
static void bluecard_enable_activity_led(bluecard_info_t *info)
{
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
if (!test_bit(CARD_HAS_PCCARD_ID, &(info->hw_state)))
return;
}
do {
- register unsigned int iobase = info->p_dev->io.BasePort1;
+ register unsigned int iobase = info->p_dev->resource[0]->start;
register unsigned int offset;
register unsigned char command;
register unsigned long ready_bit;
return;
}
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
if (test_bit(XMIT_SENDING_READY, &(info->tx_state)))
bluecard_enable_activity_led(info);
if (!test_bit(CARD_READY, &(info->hw_state)))
return IRQ_HANDLED;
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
spin_lock(&(info->lock));
static int bluecard_hci_open(struct hci_dev *hdev)
{
bluecard_info_t *info = (bluecard_info_t *)(hdev->driver_data);
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
if (test_bit(CARD_HAS_PCCARD_ID, &(info->hw_state)))
bluecard_hci_set_baud_rate(hdev, DEFAULT_BAUD_RATE);
static int bluecard_hci_close(struct hci_dev *hdev)
{
bluecard_info_t *info = (bluecard_info_t *)(hdev->driver_data);
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
if (!test_and_clear_bit(HCI_RUNNING, &(hdev->flags)))
return 0;
static int bluecard_open(bluecard_info_t *info)
{
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev;
unsigned char id;
static int bluecard_close(bluecard_info_t *info)
{
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev = info->hdev;
if (!hdev)
return;
do {
- register unsigned int iobase = info->p_dev->io.BasePort1;
+ register unsigned int iobase = info->p_dev->resource[0]->start;
register struct sk_buff *skb;
register int len;
return;
}
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
avail = bt3c_read(iobase, 0x7006);
//printk("bt3c_cs: receiving %d bytes\n", avail);
/* our irq handler is shared */
return IRQ_NONE;
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
spin_lock(&(info->lock));
unsigned int iobase, size, addr, fcs, tmp;
int i, err = 0;
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
/* Reset */
bt3c_io_write(iobase, 0x8040, 0x0404);
}
do {
- register unsigned int iobase = info->p_dev->io.BasePort1;
+ register unsigned int iobase = info->p_dev->resource[0]->start;
register struct sk_buff *skb;
register int len;
return;
}
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
do {
info->hdev->stat.byte_rx++;
/* our irq handler is shared */
return IRQ_NONE;
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
spin_lock(&(info->lock));
return;
}
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
spin_lock_irqsave(&(info->lock), flags);
static int btuart_open(btuart_info_t *info)
{
unsigned long flags;
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev;
spin_lock_init(&(info->lock));
static int btuart_close(btuart_info_t *info)
{
unsigned long flags;
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev = info->hdev;
if (!hdev)
}
do {
- register unsigned int iobase = info->p_dev->io.BasePort1;
+ register unsigned int iobase = info->p_dev->resource[0]->start;
register struct sk_buff *skb;
register int len;
return;
}
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
do {
info->hdev->stat.byte_rx++;
/* our irq handler is shared */
return IRQ_NONE;
- iobase = info->p_dev->io.BasePort1;
+ iobase = info->p_dev->resource[0]->start;
spin_lock(&(info->lock));
static int dtl1_open(dtl1_info_t *info)
{
unsigned long flags;
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev;
spin_lock_init(&(info->lock));
outb(UART_LCR_WLEN8, iobase + UART_LCR); /* Reset DLAB */
outb((UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2), iobase + UART_MCR);
- info->ri_latch = inb(info->p_dev->io.BasePort1 + UART_MSR) & UART_MSR_RI;
+ info->ri_latch = inb(info->p_dev->resource[0]->start + UART_MSR)
+ & UART_MSR_RI;
/* Turn on interrupts */
outb(UART_IER_RLSI | UART_IER_RDI | UART_IER_THRI, iobase + UART_IER);
static int dtl1_close(dtl1_info_t *info)
{
unsigned long flags;
- unsigned int iobase = info->p_dev->io.BasePort1;
+ unsigned int iobase = info->p_dev->resource[0]->start;
struct hci_dev *hdev = info->hdev;
if (!hdev)
static void set_cardparameter(struct cm4000_dev *dev)
{
int i;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
u_int8_t stopbits = 0x02; /* ISO default */
DEBUGP(3, dev, "-> set_cardparameter\n");
unsigned short num_bytes_read;
unsigned char pts_reply[4];
ssize_t rc;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
rc = 0;
static void monitor_card(unsigned long p)
{
struct cm4000_dev *dev = (struct cm4000_dev *) p;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
unsigned short s;
struct ptsreq ptsreq;
int i, atrc;
loff_t *ppos)
{
struct cm4000_dev *dev = filp->private_data;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
ssize_t rc;
int i, j, k;
size_t count, loff_t *ppos)
{
struct cm4000_dev *dev = filp->private_data;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
unsigned short s;
unsigned char tmp;
unsigned char infolen;
static long cmm_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
{
struct cm4000_dev *dev = filp->private_data;
- unsigned int iobase = dev->p_dev->io.BasePort1;
+ unsigned int iobase = dev->p_dev->resource[0]->start;
struct inode *inode = filp->f_path.dentry->d_inode;
struct pcmcia_device *link;
int size;
static void cm4040_do_poll(unsigned long dummy)
{
struct reader_dev *dev = (struct reader_dev *) dummy;
- unsigned int obs = xinb(dev->p_dev->io.BasePort1
+ unsigned int obs = xinb(dev->p_dev->resource[0]->start
+ REG_OFFSET_BUFFER_STATUS);
if ((obs & BSR_BULK_IN_FULL)) {
static int wait_for_bulk_out_ready(struct reader_dev *dev)
{
int i, rc;
- int iobase = dev->p_dev->io.BasePort1;
+ int iobase = dev->p_dev->resource[0]->start;
for (i = 0; i < POLL_LOOP_COUNT; i++) {
if ((xinb(iobase + REG_OFFSET_BUFFER_STATUS)
/* Write to Sync Control Register */
static int write_sync_reg(unsigned char val, struct reader_dev *dev)
{
- int iobase = dev->p_dev->io.BasePort1;
+ int iobase = dev->p_dev->resource[0]->start;
int rc;
rc = wait_for_bulk_out_ready(dev);
static int wait_for_bulk_in_ready(struct reader_dev *dev)
{
int i, rc;
- int iobase = dev->p_dev->io.BasePort1;
+ int iobase = dev->p_dev->resource[0]->start;
for (i = 0; i < POLL_LOOP_COUNT; i++) {
if ((xinb(iobase + REG_OFFSET_BUFFER_STATUS)
size_t count, loff_t *ppos)
{
struct reader_dev *dev = filp->private_data;
- int iobase = dev->p_dev->io.BasePort1;
+ int iobase = dev->p_dev->resource[0]->start;
size_t bytes_to_read;
unsigned long i;
size_t min_bytes_to_read;
size_t count, loff_t *ppos)
{
struct reader_dev *dev = filp->private_data;
- int iobase = dev->p_dev->io.BasePort1;
+ int iobase = dev->p_dev->resource[0]->start;
ssize_t rc;
int i;
unsigned int bytes_to_write;
dev = link->priv;
- DEBUGP(2, dev, "device " DEVICE_NAME "%d at 0x%.4x-0x%.4x\n", devno,
- link->io.BasePort1, link->io.BasePort1+link->io.NumPorts1);
+ DEBUGP(2, dev, "device " DEVICE_NAME "%d at %pR\n", devno,
+ link->resource[0]);
DEBUGP(2, dev, "<- reader_config (succ)\n");
return 0;
if (ret)
return ret;
- io_resource = request_region(p_dev->io.BasePort1, p_dev->io.NumPorts1,
+ io_resource = request_region(p_dev->resource[0]->start,
+ resource_size(p_dev->resource[0]),
IPWIRELESS_PCCARD_NAME);
if (cfg->mem.nwin == 0)
INIT_WORK(&ipw->work_reboot, signalled_reboot_work);
- ipwireless_init_hardware_v1(ipw->hardware, link->io.BasePort1,
+ ipwireless_init_hardware_v1(ipw->hardware, link->resource[0]->start,
ipw->attr_memory, ipw->common_memory,
ipw->is_v2_card, signalled_reboot_callback,
ipw);
printk(KERN_INFO IPWIRELESS_PCCARD_NAME ": Card type %s\n",
ipw->is_v2_card ? "V2/V3" : "V1");
printk(KERN_INFO IPWIRELESS_PCCARD_NAME
- ": I/O ports 0x%04x-0x%04x, irq %d\n",
- (unsigned int) link->io.BasePort1,
- (unsigned int) (link->io.BasePort1 +
- link->io.NumPorts1 - 1),
+ ": I/O ports %pR, irq %d\n", link->resource[0],
(unsigned int) link->irq);
if (ipw->attr_memory && ipw->common_memory)
printk(KERN_INFO IPWIRELESS_PCCARD_NAME
if (ret)
goto failed;
- info->io_base = link->io.BasePort1;
+ info->io_base = link->resource[0]->start;
info->irq_level = link->irq;
dev_info(&link->dev, "index 0x%02x:",
link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
+ if (link->resource[0])
+ printk(", io %pR", link->resource[0]);
printk("\n");
return 0;
pdev->io.NumPorts2 = (stk->is_kme) ? 2 : 1;
if (pcmcia_request_io(pdev, &pdev->io) != 0)
return -ENODEV;
- stk->ctl_base = pdev->io.BasePort2;
+ stk->ctl_base = pdev->resource[1]->start;
} else if ((io->nwin == 1) && (io->win[0].len >= 16)) {
pdev->io.NumPorts1 = io->win[0].len;
pdev->io.NumPorts2 = 0;
if (pcmcia_request_io(pdev, &pdev->io) != 0)
return -ENODEV;
- stk->ctl_base = pdev->io.BasePort1 + 0x0e;
+ stk->ctl_base = pdev->resource[0]->start + 0x0e;
} else
return -ENODEV;
/* If we've got this far, we're done */
if (pcmcia_loop_config(link, pcmcia_check_one_config, stk))
goto failed; /* No suitable config found */
}
- io_base = link->io.BasePort1;
+ io_base = link->resource[0]->start;
ctl_base = stk->ctl_base;
if (!link->irq)
outb(0x81, ctl_base+1);
host = idecs_register(io_base, ctl_base, link->irq, link);
- if (host == NULL && link->io.NumPorts1 == 0x20) {
+ if (host == NULL && resource_size(link->resource[0]) == 0x20) {
outb(0x02, ctl_base + 0x10);
host = idecs_register(io_base + 0x10, ctl_base + 0x10,
link->irq, link);
default:
case AVM_CARDTYPE_B1: addcard = b1pcmcia_addcard_b1; break;
}
- if ((i = (*addcard)(link->io.BasePort1, link->irq)) < 0) {
- dev_err(&link->dev, "avm_cs: failed to add AVM-Controller at i/o %#x, irq %d\n",
- link->io.BasePort1, link->irq);
+ if ((i = (*addcard)(link->resource[0]->start, link->irq)) < 0) {
+ dev_err(&link->dev,
+ "avm_cs: failed to add AVM-Controller at i/o %#x, irq %d\n",
+ (unsigned int) link->resource[0]->start, link->irq);
avmcs_release(link);
return -ENODEV;
}
static void avmcs_release(struct pcmcia_device *link)
{
- b1pcmcia_delcard(link->io.BasePort1, link->irq);
+ b1pcmcia_delcard(link->resource[0]->start, link->irq);
pcmcia_disable_device(link);
} /* avmcs_release */
}
printk(KERN_NOTICE "avma1_cs: checking at i/o %#x, irq %d\n",
- link->io.BasePort1, link->irq);
+ (unsigned int) link->resource[0]->start, link->irq);
icard.para[0] = link->irq;
- icard.para[1] = link->io.BasePort1;
+ icard.para[1] = link->resource[0]->start;
icard.protocol = isdnprot;
icard.typ = ISDN_CTYPE_A1_PCMCIA;
i = hisax_init_pcmcia(link, &busy, &icard);
if (i < 0) {
- printk(KERN_ERR "avma1_cs: failed to initialize AVM A1 PCMCIA %d at i/o %#x\n", i, link->io.BasePort1);
+ printk(KERN_ERR "avma1_cs: failed to initialize AVM A1 "
+ "PCMCIA %d at i/o %#x\n", i,
+ (unsigned int) link->resource[0]->start);
avma1cs_release(link);
return -ENODEV;
}
link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
printk("\n");
icard.para[0] = link->irq;
- icard.para[1] = link->io.BasePort1;
+ icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_ELSA_PCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
- printk(KERN_ERR "elsa_cs: failed to initialize Elsa PCMCIA %d at i/o %#x\n",
- i, link->io.BasePort1);
+ printk(KERN_ERR "elsa_cs: failed to initialize Elsa "
+ "PCMCIA %d with %pR\n", i, link->resource[0]);
elsa_cs_release(link);
} else
((local_info_t*)link->priv)->cardnr = i;
printk(", Vpp %d.%d", link->conf.Vpp/10, link->conf.Vpp%10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req->Base,
req->Base+req->Size-1);
printk("\n");
icard.para[0] = link->irq;
- icard.para[1] = link->io.BasePort1;
+ icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_SEDLBAUER_PCMCIA;
ret = hisax_init_pcmcia(link,
&(((local_info_t *)link->priv)->stop), &icard);
if (ret < 0) {
- printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d at i/o %#x\n",
- ret, link->io.BasePort1);
+ printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d with %pR\n",
+ ret, link->resource[0]);
sedlbauer_release(link);
return -ENODEV;
} else
link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
printk("\n");
icard.para[0] = link->irq;
- icard.para[1] = link->io.BasePort1;
+ icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_TELESPCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "teles_cs: failed to initialize Teles PCMCIA %d at i/o %#x\n",
- i, link->io.BasePort1);
+ i, (unsigned int) link->resource[0]->start);
teles_cs_release(link);
return -ENODEV;
}
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
ioaddr = dev->base_addr;
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
ioaddr = dev->base_addr;
EL3WINDOW(0);
if (!link->irq)
goto failed;
- if (link->io.NumPorts2 == 8) {
+ if (resource_size(link->resource[1]) == 8) {
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
}
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
if (!get_prom(link)) {
printk(KERN_NOTICE "axnet_cs: this is not an AX88190 card!\n");
goto failed;
}
- ioaddr = dev->base_addr = link->io.BasePort1;
+ ioaddr = dev->base_addr = link->resource[0]->start;
dev_dbg(&link->dev, "got ioaddr %Xh\n", ioaddr);
dev_dbg(&link->dev, "request IRQ %d\n",
if (ret == 0) {
/* calculate ConfigIndex value */
link->conf.ConfigIndex =
- ((link->io.BasePort1 & 0x0f0) >> 3) | 0x22;
+ ((link->resource[0]->start & 0x0f0) >> 3) | 0x22;
return ret;
}
}
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
- if (link->io.BasePort2 != 0) {
+ if (resource_size(link->resource[1]) != 0) {
ret = fmvj18x_setup_mfc(link);
if (ret != 0) goto failed;
}
if (ret)
goto failed;
}
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
ret = pcmcia_request_exclusive_irq(link, ibmtr_interrupt);
if (ret)
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
ioaddr = dev->base_addr;
if (!link->irq)
goto failed;
- if (link->io.NumPorts2 == 8) {
+ if (resource_size(link->resource[1]) == 8) {
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
}
if (ret)
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
if (info->flags & HAS_MISC_REG) {
if ((if_port == 1) || (if_port == 2))
dev->if_port = if_port;
if (pcmcia_loop_config(link, mhz_mfc_config_check, NULL))
return -ENODEV;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
/* Allocate a memory window, for accessing the ISR */
req.Attributes = WIN_DATA_WIDTH_8|WIN_MEMORY_TYPE_AM|WIN_ENABLE;
struct net_device *dev = link->priv;
struct smc_private *smc = netdev_priv(dev);
unsigned int ioaddr = dev->base_addr;
- unsigned int iouart = link->io.BasePort2;
+ unsigned int iouart = link->resource[1]->start;
/* Set UART base address and force map with COR bit 1 */
writeb(iouart & 0xff, smc->base + MOT_UART + CISREG_IOBASE_0);
link->io.NumPorts1 = 16;
i = pcmcia_loop_config(link, smc_configcheck, NULL);
if (!i)
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
return i;
}
link->io.NumPorts2 = 0;
i = pcmcia_request_io(link, &link->io);
}
- dev->base_addr = link->io.BasePort1 + 0x10;
+ dev->base_addr = link->resource[0]->start + 0x10;
return i;
}
/* Download the Seven of Diamonds firmware */
for (i = 0; i < fw->size; i++) {
- outb(fw->data[i], link->io.BasePort1 + 2);
+ outb(fw->data[i], link->resource[0]->start + 2);
udelay(50);
}
release_firmware(fw);
return rc;
} else if (manfid == MANFID_OSITECH) {
/* Make sure both functions are powered up */
- set_bits(0x300, link->io.BasePort1 + OSITECH_AUI_PWR);
+ set_bits(0x300, link->resource[0]->start + OSITECH_AUI_PWR);
/* Now, turn on the interrupt for both card functions */
- set_bits(0x300, link->io.BasePort1 + OSITECH_RESET_ISR);
+ set_bits(0x300, link->resource[0]->start + OSITECH_RESET_ISR);
dev_dbg(&link->dev, "AUI/PWR: %4.4x RESET/ISR: %4.4x\n",
- inw(link->io.BasePort1 + OSITECH_AUI_PWR),
- inw(link->io.BasePort1 + OSITECH_RESET_ISR));
+ inw(link->resource[0]->start + OSITECH_AUI_PWR),
+ inw(link->resource[0]->start + OSITECH_RESET_ISR));
}
return 0;
}
* the base address of the ethernet port (BasePort1) is written
* to the BAR registers of the modem.
*/
- err = pcmcia_write_config_byte(link, CISREG_IOBASE_0,
- link->io.BasePort2 & 0xff);
+ err = pcmcia_write_config_byte(link, CISREG_IOBASE_0, (u8)
+ link->resource[1]->start & 0xff);
if (err)
goto config_error;
err = pcmcia_write_config_byte(link, CISREG_IOBASE_1,
- (link->io.BasePort2 >> 8) & 0xff);
+ (link->resource[1]->start >> 8) & 0xff);
if (err)
goto config_error;
* part.
*/
writeb(0x47, local->dingo_ccr + CISREG_COR);
- ioaddr = link->io.BasePort1;
+ ioaddr = link->resource[0]->start;
writeb(ioaddr & 0xff , local->dingo_ccr + CISREG_IOBASE_0);
writeb((ioaddr >> 8)&0xff , local->dingo_ccr + CISREG_IOBASE_1);
/* we can now register the device with the net subsystem */
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
if (local->dingo)
do_reset(dev, 1); /* a kludge to make the cem56 work */
goto failed;
((local_info_t *)link->priv)->eth_dev =
init_airo_card(link->irq,
- link->io.BasePort1, 1, &link->dev);
+ link->resource[0]->start, 1, &link->dev);
if (!((local_info_t *)link->priv)->eth_dev)
goto failed;
if (link->conf.Vpp)
printk(", Vpp %d.%d", link->conf.Vpp/10, link->conf.Vpp%10);
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req->Base,
req->Base+req->Size-1);
((local_info_t*)link->priv)->eth_dev =
init_atmel_card(link->irq,
- link->io.BasePort1,
+ link->resource[0]->start,
did ? did->driver_info : ATMEL_FW_TYPE_NONE,
&link->dev,
card_present,
struct hostap_cs_priv *hw_priv = local->hw_priv;
res = pcmcia_write_config_byte(hw_priv->link, 0x10,
- hw_priv->link->io.BasePort1 & 0x00ff);
+ hw_priv->link->resource[0]->start & 0x00ff);
if (res != 0) {
printk(KERN_DEBUG "Prism3 SanDisk - failed to set I/O base 0 -"
" res=%d\n", res);
udelay(10);
res = pcmcia_write_config_byte(hw_priv->link, 0x12,
- (hw_priv->link->io.BasePort1 >> 8) & 0x00ff);
+ (hw_priv->link->resource[0]->start >> 8) & 0x00ff);
if (res != 0) {
printk(KERN_DEBUG "Prism3 SanDisk - failed to set I/O base 1 -"
" res=%d\n", res);
local_info_t *local = iface->local;
struct hostap_cs_priv *hw_priv = local->hw_priv;
- if (hw_priv->link->io.NumPorts1 < 0x42) {
+ if (resource_size(hw_priv->link->resource[0]) < 0x42) {
/* Not enough ports to be SanDisk multi-function card */
ret = -ENODEV;
goto done;
goto failed_unlock;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
spin_unlock_irqrestore(&local->irq_init_lock, flags);
link->conf.Vpp % 10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
printk("\n");
local->shutdown = 0;
goto out1;
/* Initialize io access */
- card->iobase = ioport_map(p_dev->io.BasePort1, p_dev->io.NumPorts1);
+ card->iobase = ioport_map(p_dev->resource[0]->start,
+ resource_size(p_dev->resource[0]));
if (!card->iobase) {
lbs_pr_err("error in ioport_map\n");
ret = -EIO;
}
/* Finally, report what we've done */
- lbs_deb_cs("irq %d, io 0x%04x-0x%04x\n",
- p_dev->irq, p_dev->io.BasePort1,
- p_dev->io.BasePort1 + p_dev->io.NumPorts1 - 1);
+ lbs_deb_cs("irq %d, io %pR", p_dev->irq, p_dev->resource[0]);
/*
* Most of the libertas cards can do unaligned register access, but some
/* We initialize the hermes structure before completing PCMCIA
* configuration just in case the interrupt handler gets
* called. */
- mem = ioport_map(link->io.BasePort1, link->io.NumPorts1);
+ mem = ioport_map(link->resource[0]->start,
+ resource_size(link->resource[0]));
if (!mem)
goto failed;
}
/* Register an interface with the stack */
- if (orinoco_if_add(priv, link->io.BasePort1,
+ if (orinoco_if_add(priv, link->resource[0]->start,
link->irq, NULL) != 0) {
printk(KERN_ERR PFX "orinoco_if_add() failed\n");
goto failed;
/* We initialize the hermes structure before completing PCMCIA
* configuration just in case the interrupt handler gets
* called. */
- mem = ioport_map(link->io.BasePort1, link->io.NumPorts1);
+ mem = ioport_map(link->resource[0]->start,
+ resource_size(link->resource[0]));
if (!mem)
goto failed;
}
/* Register an interface with the stack */
- if (orinoco_if_add(priv, link->io.BasePort1,
+ if (orinoco_if_add(priv, link->resource[0]->start,
link->irq, NULL) != 0) {
printk(KERN_ERR PFX "orinoco_if_add() failed\n");
goto failed;
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
SET_NETDEV_DEV(dev, &link->dev);
if (register_netdev(dev)) {
printk(KERN_NOTICE "wl3501_cs: register_netdev() failed\n");
if (ret)
goto failed;
- p = parport_pc_probe_port(link->io.BasePort1, link->io.BasePort2,
+ p = parport_pc_probe_port(link->resource[0]->start,
+ link->resource[1]->start,
link->irq, PARPORT_DMA_NONE,
&link->dev, IRQF_SHARED);
if (p == NULL) {
printk(KERN_NOTICE "parport_cs: parport_pc_probe_port() at "
- "0x%3x, irq %u failed\n", link->io.BasePort1,
+ "0x%3x, irq %u failed\n",
+ (unsigned int) link->resource[0]->start,
link->irq);
goto failed;
}
/* Set configuration options for the aha152x driver */
memset(&s, 0, sizeof(s));
s.conf = "PCMCIA setup";
- s.io_port = link->io.BasePort1;
+ s.io_port = link->resource[0]->start;
s.irq = link->irq;
s.scsiid = host_id;
s.reconnect = reconnect;
goto failed;
/* A bad hack... */
- release_region(link->io.BasePort1, link->io.NumPorts1);
+ release_region(link->resource[0]->start, resource_size(link->resource[0]));
/* Set configuration options for the fdomain driver */
- sprintf(str, "%d,%d", link->io.BasePort1, link->irq);
+ sprintf(str, "%d,%d", (unsigned int) link->resource[0]->start, link->irq);
fdomain_setup(str);
host = __fdomain_16x0_detect(&fdomain_driver_template);
goto cs_failed;
if (free_ports) {
- if (link->io.BasePort1) {
- release_region(link->io.BasePort1, link->io.NumPorts1);
+ if (link->resource[0]) {
+ release_region(link->resource[0]->start,
+ resource_size(link->resource[0]));
}
- if (link->io.BasePort2) {
- release_region(link->io.BasePort2, link->io.NumPorts2);
+ if (link->resource[1]) {
+ release_region(link->resource[1]->start,
+ resource_size(link->resource[1]));
}
}
/* Set port and IRQ */
- data->BaseAddress = link->io.BasePort1;
- data->NumAddress = link->io.NumPorts1;
+ data->BaseAddress = link->resource[0]->start;
+ data->NumAddress = resource_size(link->resource[0]);
data->IrqNumber = link->irq;
nsp_dbg(NSP_DEBUG_INIT, "I/O[0x%x+0x%x] IRQ %d",
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
printk(", irq %d", link->irq);
}
- if (link->io.NumPorts1) {
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
- }
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2+link->io.NumPorts2-1);
+ if (link->resource[0])
+ printk(", io %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", cfg_mem->req.Base,
cfg_mem->req.Base+cfg_mem->req.Size-1);
if ((info->manf_id == MANFID_MACNICA) || (info->manf_id == MANFID_PIONEER) || (info->manf_id == 0x0098)) {
/* set ATAcmd */
- outb(0xb4, link->io.BasePort1 + 0xd);
- outb(0x24, link->io.BasePort1 + 0x9);
- outb(0x04, link->io.BasePort1 + 0xd);
+ outb(0xb4, link->resource[0]->start + 0xd);
+ outb(0x24, link->resource[0]->start + 0x9);
+ outb(0x04, link->resource[0]->start + 0xd);
}
/* The KXL-810AN has a bigger IO port window */
- if (link->io.NumPorts1 == 32)
+ if (resource_size(link->resource[0]) == 32)
host = qlogic_detect(&qlogicfas_driver_template, link,
- link->io.BasePort1 + 16, link->irq);
+ link->resource[0]->start + 16, link->irq);
else
host = qlogic_detect(&qlogicfas_driver_template, link,
- link->io.BasePort1, link->irq);
+ link->resource[0]->start, link->irq);
if (!host) {
printk(KERN_INFO "%s: no SCSI devices found\n", qlogic_name);
if ((info->manf_id == MANFID_MACNICA) ||
(info->manf_id == MANFID_PIONEER) ||
(info->manf_id == 0x0098)) {
- outb(0x80, link->io.BasePort1 + 0xd);
- outb(0x24, link->io.BasePort1 + 0x9);
- outb(0x04, link->io.BasePort1 + 0xd);
+ outb(0x80, link->resource[0]->start + 0xd);
+ outb(0x24, link->resource[0]->start + 0x9);
+ outb(0x04, link->resource[0]->start + 0xd);
}
/* Ugggglllyyyy!!! */
qlogicfas408_bus_reset(NULL);
(info->manf_id == MANFID_PIONEER) ||
(info->manf_id == 0x0098)) {
/* set ATAcmd */
- outb(0xb4, link->io.BasePort1 + 0xd);
- outb(0x24, link->io.BasePort1 + 0x9);
- outb(0x04, link->io.BasePort1 + 0xd);
+ outb(0xb4, link->resource[0]->start + 0xd);
+ outb(0x24, link->resource[0]->start + 0x9);
+ outb(0x04, link->resource[0]->start + 0xd);
}
/*
* 0x130, 0x230, 0x280, 0x290,
* 0x320, 0x330, 0x340, 0x350
*/
- port_base = link->io.BasePort1;
+ port_base = link->resource[0]->start;
irq_level = link->irq;
DEB(printk("SYM53C500: port_base=0x%x, irq=%d, fast_pio=%d\n",
if ((info->manf_id == MANFID_MACNICA) ||
(info->manf_id == MANFID_PIONEER) ||
(info->manf_id == 0x0098)) {
- outb(0x80, link->io.BasePort1 + 0xd);
- outb(0x24, link->io.BasePort1 + 0x9);
- outb(0x04, link->io.BasePort1 + 0xd);
+ outb(0x80, link->resource[0]->start + 0xd);
+ outb(0x24, link->resource[0]->start + 0x9);
+ outb(0x04, link->resource[0]->start + 0xd);
}
/*
* If things don't work after a "resume",
* this is a good place to start looking.
*/
- SYM53C500_int_host_reset(link->io.BasePort1);
+ SYM53C500_int_host_reset(link->resource[0]->start);
return 0;
}
/* If the card is already configured, look up the port and irq */
if (link->function_config) {
unsigned int port = 0;
- if ((link->io.BasePort2 != 0) &&
- (link->io.NumPorts2 == 8)) {
- port = link->io.BasePort2;
+ if ((link->resource[1]->end != 0) &&
+ (resource_size(link->resource[1]) == 8)) {
+ port = link->resource[1]->end;
info->slave = 1;
} else if ((info->manfid == MANFID_OSITECH) &&
- (link->io.NumPorts1 == 0x40)) {
- port = link->io.BasePort1 + 0x28;
+ (resource_size(link->resource[0]) == 0x40)) {
+ port = link->resource[0]->start + 0x28;
info->slave = 1;
}
if (info->slave) {
i = pcmcia_request_configuration(link, &link->conf);
if (i != 0)
return -1;
- return setup_serial(link, info, link->io.BasePort1, link->irq);
+ return setup_serial(link, info, link->resource[0]->start, link->irq);
}
static int multi_config_check(struct pcmcia_device *p_dev,
p_dev->io.BasePort1 = cf->io.win[0].base;
p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
if (!pcmcia_request_io(p_dev, &p_dev->io)) {
- *base2 = p_dev->io.BasePort1 + 8;
+ *base2 = p_dev->resource[0]->start + 8;
return 0;
}
}
p_dev->io.BasePort2 = cf->io.win[1].base;
p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
if (!pcmcia_request_io(p_dev, &p_dev->io)) {
- *base2 = p_dev->io.BasePort2;
+ *base2 = p_dev->resource[1]->start;
return 0;
}
}
link->conf.ConfigIndex == 3) {
err = setup_serial(link, info, base2,
link->irq);
- base2 = link->io.BasePort1;
+ base2 = link->resource[0]->start;;
} else {
- err = setup_serial(link, info, link->io.BasePort1,
+ err = setup_serial(link, info, link->resource[0]->start,
link->irq);
}
info->c950ctrl = base2;
return 0;
}
- setup_serial(link, info, link->io.BasePort1, link->irq);
+ setup_serial(link, info, link->resource[0]->start, link->irq);
for (i = 0; i < info->multi - 1; i++)
setup_serial(link, info, base2 + (8 * i),
link->irq);
if (!link)
return -EIO;
- dev->iobase = link->io.BasePort1;
+ dev->iobase = link->resource[0]->start;;
printk("I/O base=0x%04lx ", dev->iobase);
printk("fingerprint:\n");
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %u", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(", io %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(", io %pR", link->resource[1]);
printk("\n");
return;
printk(" no pcmcia cards found\n");
return -EIO;
}
- iobase = link->io.BasePort1;
+ iobase = link->resource[0]->start;
} else {
printk(" bug! board does not have PCMCIA bustype\n");
return -EINVAL;
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %u", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(", io %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
printk("\n");
return;
link = pcmcia_cur_dev; /* XXX hack */
if (!link)
return -EIO;
- iobase = link->io.BasePort1;
+ iobase = link->resource[0]->start;
#ifdef incomplete
irq = link->irq;
#endif
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(", io %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req.Base,
req.Base + req.Size - 1);
link = pcmcia_cur_dev; /* XXX hack */
if (!link)
return -EIO;
- iobase = link->io.BasePort1;
+ iobase = link->resource[0]->start;
#ifdef incomplete
irq = link->irq;
#endif
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req.Base,
req.Base + req.Size - 1);
link = pcmcia_cur_dev; /* XXX hack */
if (!link)
return -EIO;
- iobase = link->io.BasePort1;
+ iobase = link->resource[0]->start;
irq = link->irq;
break;
default:
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req.Base,
req.Base + req.Size - 1);
return -EIO;
dev->driver = &driver_ni_mio_cs;
- dev->iobase = link->io.BasePort1;
+ dev->iobase = link->resource[0]->start;
irq = link->irq;
}
}
- dev->iobase = local->link->io.BasePort1;
+ dev->iobase = local->link->resource[0]->start;
ret = alloc_subdevices(dev, 4);
if (ret < 0)
dev_info(&link->dev, "index 0x%02x", link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %u", link->irq);
- if (link->io.NumPorts1)
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1 + link->io.NumPorts1 - 1);
- if (link->io.NumPorts2)
- printk(" & 0x%04x-0x%04x", link->io.BasePort2,
- link->io.BasePort2 + link->io.NumPorts2 - 1);
+ if (link->resource[0])
+ printk(" & %pR", link->resource[0]);
+ if (link->resource[1])
+ printk(" & %pR", link->resource[1]);
printk("\n");
return;
goto failed;
dev->irq = link->irq;
- dev->base_addr = link->io.BasePort1;
+ dev->base_addr = link->resource[0]->start;
SET_NETDEV_DEV(dev, &link->dev);
if (register_netdev(dev) != 0) {
/*
* Register the card with the core.
*/
- j = ixj_pcmcia_probe(link->io.BasePort1, link->io.BasePort1 + 0x10);
+ j = ixj_pcmcia_probe(link->resource[0]->start,
+ link->resource[0]->start + 0x10);
info->ndev = 1;
ixj_get_serial(link, j);
goto failed;
/* require an IRQ and two registers */
- if (!link->io.NumPorts1 || link->io.NumPorts1 < 2)
+ if (resource_size(link->resource[0]) < 2)
goto failed;
if (!link->irq)
if (link->conf.Vpp)
printk(", Vpp %d.%d", link->conf.Vpp/10, link->conf.Vpp%10);
printk(", irq %d", link->irq);
- printk(", io 0x%04x-0x%04x", link->io.BasePort1,
- link->io.BasePort1+link->io.NumPorts1-1);
+ printk(", io %pR", link->resource[0]);
printk("\n");
- if (sl811_hc_init(parent, link->io.BasePort1, link->irq)
+ if (sl811_hc_init(parent, link->resource[0]->start, link->irq)
< 0) {
failed:
printk(KERN_WARNING "sl811_cs_config failed\n");
if (ret)
goto failed;
- if (snd_pdacf_assign_resources(pdacf, link->io.BasePort1, link->irq) < 0)
+ if (snd_pdacf_assign_resources(pdacf, link->resource[0]->start,
+ link->irq) < 0)
goto failed;
return 0;
chip->dev = &link->dev;
snd_card_set_dev(chip->card, chip->dev);
- if (snd_vxpocket_assign_resources(chip, link->io.BasePort1, link->irq) < 0)
+ if (snd_vxpocket_assign_resources(chip, link->resource[0]->start,
+ link->irq) < 0)
goto failed;
return 0;