source "drivers/firewire/Kconfig"
config IEEE1394
- tristate "IEEE 1394 (FireWire) support"
+ tristate "Stable FireWire stack"
depends on PCI || BROKEN
help
IEEE 1394 describes a high performance serial bus, which is also
To compile this driver as a module, say M here: the
module will be called ieee1394.
-comment "Subsystem Options"
- depends on IEEE1394
-
-config IEEE1394_VERBOSEDEBUG
- bool "Excessive debugging output"
- depends on IEEE1394
+config IEEE1394_OHCI1394
+ tristate "OHCI-1394 controllers"
+ depends on PCI && IEEE1394
help
- If you say Y here, you will get very verbose debugging logs from
- the subsystem which includes a dump of the header of every sent
- and received packet. This can amount to a high amount of data
- collected in a very short time which is usually also saved to
- disk by the system logging daemons.
+ Enable this driver if you have an IEEE 1394 controller based on the
+ OHCI-1394 specification. The current driver is only tested with OHCI
+ chipsets made by Texas Instruments and NEC. Most third-party vendors
+ use one of these chipsets. It should work with any OHCI-1394
+ compliant card, however.
- Say Y if you really want or need the debugging output, everyone
- else says N.
+ To compile this driver as a module, say M here: the
+ module will be called ohci1394.
-comment "Controllers"
- depends on IEEE1394
+ NOTE:
-comment "Texas Instruments PCILynx requires I2C"
+ You should only build either ohci1394 or the new firewire-ohci driver,
+ but not both. If you nevertheless want to install both, you should
+ configure them only as modules and blacklist the driver(s) which you
+ don't want to have auto-loaded. Add either
+
+ blacklist firewire-ohci
+ or
+ blacklist ohci1394
+ blacklist video1394
+ blacklist dv1394
+
+ to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf
+ depending on your distribution. The latter two modules should be
+ blacklisted together with ohci1394 because they depend on ohci1394.
+
+ If you have an old modprobe which doesn't implement the blacklist
+ directive, use "install modulename /bin/true" for the modules to be
+ blacklisted.
+
+comment "PCILynx controller requires I2C"
depends on IEEE1394 && I2C=n
config IEEE1394_PCILYNX
- tristate "Texas Instruments PCILynx support"
+ tristate "PCILynx controller"
depends on PCI && IEEE1394 && I2C
select I2C_ALGOBIT
help
PowerMacs G3 B&W contain the PCILynx controller. Therefore
almost everybody can say N here.
-config IEEE1394_OHCI1394
- tristate "OHCI-1394 support"
- depends on PCI && IEEE1394
- help
- Enable this driver if you have an IEEE 1394 controller based on the
- OHCI-1394 specification. The current driver is only tested with OHCI
- chipsets made by Texas Instruments and NEC. Most third-party vendors
- use one of these chipsets. It should work with any OHCI-1394
- compliant card, however.
-
- To compile this driver as a module, say M here: the
- module will be called ohci1394.
-
-comment "Protocols"
- depends on IEEE1394
-
-config IEEE1394_VIDEO1394
- tristate "OHCI-1394 Video support"
- depends on IEEE1394 && IEEE1394_OHCI1394
- help
- This option enables video device usage for OHCI-1394 cards. Enable
- this option only if you have an IEEE 1394 video device connected to
- an OHCI-1394 card.
-
comment "SBP-2 support (for storage devices) requires SCSI"
depends on IEEE1394 && SCSI=n
config IEEE1394_SBP2
- tristate "SBP-2 support (Harddisks etc.)"
+ tristate "Storage devices (SBP-2 protocol)"
depends on IEEE1394 && SCSI
help
This option enables you to use SBP-2 devices connected to an IEEE
The module is called eth1394 although it does not emulate Ethernet.
+config IEEE1394_RAWIO
+ tristate "raw1394 userspace interface"
+ depends on IEEE1394
+ help
+ This option adds support for the raw1394 device file which enables
+ direct communication of user programs with IEEE 1394 devices
+ (isochronous and asynchronous). Almost all application programs
+ which access FireWire require this option.
+
+ To compile this driver as a module, say M here: the module will be
+ called raw1394.
+
+config IEEE1394_VIDEO1394
+ tristate "video1394 userspace interface"
+ depends on IEEE1394 && IEEE1394_OHCI1394
+ help
+ This option adds support for the video1394 device files which enable
+ isochronous communication of user programs with IEEE 1394 devices,
+ especially video capture or export. This interface is used by all
+ libdc1394 based programs and by several other programs, in addition to
+ the raw1394 interface. It is generally not required for DV capture.
+
+ To compile this driver as a module, say M here: the module will be
+ called video1394.
+
config IEEE1394_DV1394
- tristate "OHCI-DV I/O support (deprecated)"
+ tristate "dv1394 userspace interface (deprecated)"
depends on IEEE1394 && IEEE1394_OHCI1394
help
The dv1394 driver is unsupported and may be removed from Linux in a
future release. Its functionality is now provided by raw1394 together
with libraries such as libiec61883.
-config IEEE1394_RAWIO
- tristate "Raw IEEE1394 I/O support"
+config IEEE1394_VERBOSEDEBUG
+ bool "Excessive debugging output"
depends on IEEE1394
help
- This option adds support for the raw1394 device file which enables
- direct communication of user programs with the IEEE 1394 bus and thus
- with the attached peripherals. Almost all application programs which
- access FireWire require this option.
+ If you say Y here, you will get very verbose debugging logs from the
+ ieee1394 drivers, including sent and received packet headers. This
+ will quickly result in large amounts of data sent to the system log.
- To compile this driver as a module, say M here: the module will be
- called raw1394.
+ Say Y if you really need the debugging output. Everyone else says N.
endmenu
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff