ARM: lh7a40x: remove unmaintained platform support
authorRussell King <rmk+kernel@arm.linux.org.uk>
Fri, 21 Jan 2011 11:04:45 +0000 (11:04 +0000)
committerRussell King <rmk+kernel@arm.linux.org.uk>
Mon, 24 Jan 2011 19:05:19 +0000 (19:05 +0000)
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006.  As such, it is a maintainence burden with no benefit.

This gets rid of two defconfigs.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
58 files changed:
Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen [deleted file]
Documentation/arm/Sharp-LH/CompactFlash [deleted file]
Documentation/arm/Sharp-LH/IOBarrier [deleted file]
Documentation/arm/Sharp-LH/KEV7A400 [deleted file]
Documentation/arm/Sharp-LH/LCDPanels [deleted file]
Documentation/arm/Sharp-LH/LPD7A400 [deleted file]
Documentation/arm/Sharp-LH/LPD7A40X [deleted file]
Documentation/arm/Sharp-LH/SDRAM [deleted file]
Documentation/arm/Sharp-LH/VectoredInterruptController [deleted file]
arch/arm/Kconfig
arch/arm/Makefile
arch/arm/configs/lpd7a400_defconfig [deleted file]
arch/arm/configs/lpd7a404_defconfig [deleted file]
arch/arm/include/asm/setup.h
arch/arm/mach-lh7a40x/Kconfig [deleted file]
arch/arm/mach-lh7a40x/Makefile [deleted file]
arch/arm/mach-lh7a40x/Makefile.boot [deleted file]
arch/arm/mach-lh7a40x/arch-kev7a400.c [deleted file]
arch/arm/mach-lh7a40x/arch-lpd7a40x.c [deleted file]
arch/arm/mach-lh7a40x/clcd.c [deleted file]
arch/arm/mach-lh7a40x/clocks.c [deleted file]
arch/arm/mach-lh7a40x/common.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/clocks.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/constants.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/debug-macro.S [deleted file]
arch/arm/mach-lh7a40x/include/mach/dma.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/entry-macro.S [deleted file]
arch/arm/mach-lh7a40x/include/mach/hardware.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/io.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/irqs.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/memory.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/registers.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/ssp.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/system.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/timex.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/uncompress.h [deleted file]
arch/arm/mach-lh7a40x/include/mach/vmalloc.h [deleted file]
arch/arm/mach-lh7a40x/irq-kev7a400.c [deleted file]
arch/arm/mach-lh7a40x/irq-lh7a400.c [deleted file]
arch/arm/mach-lh7a40x/irq-lh7a404.c [deleted file]
arch/arm/mach-lh7a40x/irq-lpd7a40x.c [deleted file]
arch/arm/mach-lh7a40x/lcd-panel.h [deleted file]
arch/arm/mach-lh7a40x/ssp-cpld.c [deleted file]
arch/arm/mach-lh7a40x/time.c [deleted file]
drivers/net/smc91x.h
drivers/tty/serial/Kconfig
drivers/tty/serial/Makefile
drivers/tty/serial/serial_lh7a40x.c [deleted file]
drivers/usb/Kconfig
drivers/usb/gadget/Kconfig
drivers/usb/gadget/Makefile
drivers/usb/gadget/gadget_chips.h
drivers/usb/gadget/lh7a40x_udc.c [deleted file]
drivers/usb/gadget/lh7a40x_udc.h [deleted file]
drivers/usb/host/ohci-hcd.c
drivers/usb/host/ohci-lh7a404.c [deleted file]
drivers/usb/host/ohci.h
drivers/video/Kconfig

diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
deleted file mode 100644 (file)
index dc460f0..0000000
+++ /dev/null
@@ -1,61 +0,0 @@
-README on the ADC/Touchscreen Controller
-========================================
-
-The LH79524 and LH7A404 include a built-in Analog to Digital
-controller (ADC) that is used to process input from a touchscreen.
-The driver only implements a four-wire touch panel protocol.
-
-The touchscreen driver is maintenance free except for the pen-down or
-touch threshold.  Some resistive displays and board combinations may
-require tuning of this threshold.  The driver exposes some of its
-internal state in the sys filesystem.  If the kernel is configured
-with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a
-directory
-
-  /sys/devices/platform/adc-lh7.0
-
-containing these files.
-
-  -r--r--r--    1 root     root         4096 Jan  1 00:00 samples
-  -rw-r--r--    1 root     root         4096 Jan  1 00:00 threshold
-  -r--r--r--    1 root     root         4096 Jan  1 00:00 threshold_range
-
-The threshold is the current touch threshold.  It defaults to 750 on
-most targets.
-
-  # cat threshold
- 750
-
-The threshold_range contains the range of valid values for the
-threshold.  Values outside of this range will be silently ignored.
-
-  # cat threshold_range
-  0 1023
-
-To change the threshold, write a value to the threshold file.
-
-  # echo 500 > threshold
-  # cat threshold
-  500
-
-The samples file contains the most recently sampled values from the
-ADC.  There are 12.  Below are typical of the last sampled values when
-the pen has been released.  The first two and last two samples are for
-detecting whether or not the pen is down.  The third through sixth are
-X coordinate samples.  The seventh through tenth are Y coordinate
-samples.
-
-  # cat samples
-  1023 1023 0 0 0 0 530 529 530 529 1023 1023
-
-To determine a reasonable threshold, press on the touch panel with an
-appropriate stylus and read the values from samples.
-
-  # cat samples
-  1023 676 92 103 101 102 855 919 922 922 1023 679
-
-The first and eleventh samples are discarded.  Thus, the important
-values are the second and twelfth which are used to determine if the
-pen is down.  When both are below the threshold, the driver registers
-that the pen is down.  When either is above the threshold, it
-registers then pen is up.
diff --git a/Documentation/arm/Sharp-LH/CompactFlash b/Documentation/arm/Sharp-LH/CompactFlash
deleted file mode 100644 (file)
index 8616d87..0000000
+++ /dev/null
@@ -1,32 +0,0 @@
-README on the Compact Flash for Card Engines
-============================================
-
-There are three challenges in supporting the CF interface of the Card
-Engines.  First, every IO operation must be followed with IO to
-another memory region.  Second, the slot is wired for one-to-one
-address mapping *and* it is wired for 16 bit access only.  Second, the
-interrupt request line from the CF device isn't wired.
-
-The IOBARRIER issue is covered in README.IOBARRIER.  This isn't an
-onerous problem.  Enough said here.
-
-The addressing issue is solved in the
-arch/arm/mach-lh7a40x/ide-lpd7a40x.c file with some awkward
-work-arounds.  We implement a special SELECT_DRIVE routine that is
-called before the IDE driver performs its own SELECT_DRIVE.  Our code
-recognizes that the SELECT register cannot be modified without also
-writing a command.  It send an IDLE_IMMEDIATE command on selecting a
-drive.  The function also prevents drive select to the slave drive
-since there can be only one.  The awkward part is that the IDE driver,
-even though we have a select procedure, also attempts to change the
-drive by writing directly the SELECT register.  This attempt is
-explicitly blocked by the OUTB function--not pretty, but effective.
-
-The lack of interrupts is a more serious problem.  Even though the CF
-card is fast when compared to a normal IDE device, we don't know that
-the CF is really flash.  A user could use one of the very small hard
-drives being shipped with a CF interface.  The IDE code includes a
-check for interfaces that lack an IRQ.  In these cases, submitting a
-command to the IDE controller is followed by a call to poll for
-completion.  If the device isn't immediately ready, it schedules a
-timer to poll again later.
diff --git a/Documentation/arm/Sharp-LH/IOBarrier b/Documentation/arm/Sharp-LH/IOBarrier
deleted file mode 100644 (file)
index 2e953e2..0000000
+++ /dev/null
@@ -1,45 +0,0 @@
-README on the IOBARRIER for CardEngine IO
-=========================================
-
-Due to an unfortunate oversight when the Card Engines were designed,
-the signals that control access to some peripherals, most notably the
-SMC91C9111 ethernet controller, are not properly handled.
-
-The symptom is that some back to back IO with the peripheral returns
-unreliable data.  With the SMC chip, you'll see errors about the bank
-register being 'screwed'.
-
-The cause is that the AEN signal to the SMC chip does not transition
-for every memory access.  It is driven through the CPLD from the CS7
-line of the CPU's static memory controller which is optimized to
-eliminate unnecessary transitions.  Yet, the SMC requires a transition
-for every write access.  The Sharp website has more information about
-the effect this power-conserving feature has on peripheral
-interfacing.
-
-The solution is to follow every write access to the SMC chip with an
-access to another memory region that will force the CPU to release the
-chip select line.  It is important to guarantee that this access
-forces the CPU off-chip.  We map a page of SDRAM as if it were an
-uncacheable IO device and read from it after every SMC IO write
-operation.
-
-  SMC IO
-  BARRIER IO
-
-Only this sequence is important.  It does not matter that there is no
-BARRIER IO before the access to the SMC chip because the AEN latch
-only needs occurs after the SMC IO write cycle.  The routines that
-implement this work-around make an additional concession which is to
-disable interrupts during the IO sequence.  Other hardware devices
-(the LogicPD CPLD) have registers in the same physical memory
-region as the SMC chip.  An interrupt might allow an access to one of
-those registers while SMC IO is being performed.
-
-You might be tempted to think that we have to access another device
-attached to the static memory controller, but the empirical evidence
-indicates that this is not so.  Mapping 0x00000000 (flash) and
-0xc0000000 (SDRAM) appear to have the same effect.  Using SDRAM seems
-to be faster.  Choosing to access an undecoded memory region is not
-desirable as there is no way to know how that chip select will be used
-in the future.
diff --git a/Documentation/arm/Sharp-LH/KEV7A400 b/Documentation/arm/Sharp-LH/KEV7A400
deleted file mode 100644 (file)
index be32b14..0000000
+++ /dev/null
@@ -1,8 +0,0 @@
-README on Implementing Linux for Sharp's KEV7a400
-=================================================
-
-This product has been discontinued by Sharp.  For the time being, the
-partially implemented code remains in the kernel.  At some point in
-the future, either the code will be finished or it will be removed
-completely.  This depends primarily on how many of the development
-boards are in the field.
diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels
deleted file mode 100644 (file)
index fb1b21c..0000000
+++ /dev/null
@@ -1,59 +0,0 @@
-README on the LCD Panels
-========================
-
-Configuration options for several LCD panels, available from Logic PD,
-are included in the kernel source.  This README will help you
-understand the configuration data and give you some guidance for
-adding support for other panels if you wish.
-
-
-lcd-panels.h
-------------
-
-There is no way, at present, to detect which panel is attached to the
-system at runtime.  Thus the kernel configuration is static.  The file
-arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the
-panel specific parameters.
-
-It should be possible for this data to be shared among several device
-families.  The current layout may be insufficiently general, but it is
-amenable to improvement.
-
-
-PIXEL_CLOCK
------------
-
-The panel data sheets will give a range of acceptable pixel clocks.
-The fundamental LCDCLK input frequency is divided down by a PCD
-constant in field '.tim2'.  It may happen that it is impossible to set
-the pixel clock within this range.  A clock which is too slow will
-tend to flicker.  For the highest quality image, set the clock as high
-as possible.
-
-
-MARGINS
--------
-
-These values may be difficult to glean from the panel data sheet.  In
-the case of the Sharp panels, the upper margin is explicitly called
-out as a specific number of lines from the top of the frame.  The
-other values may not matter as much as the panels tend to
-automatically center the image.
-
-
-Sync Sense
-----------
-
-The sense of the hsync and vsync pulses may be called out in the data
-sheet.  On one panel, the sense of these pulses determine the height
-of the visible region on the panel.  Most of the Sharp panels use
-negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in
-'.tim2'.
-
-
-Pel Layout
-----------
-
-The Sharp color TFT panels are all configured for 16 bit direct color
-modes.  The amba-lcd driver sets the pel mode to 565 for 5 bits of
-each red and blue and 6 bits of green.
diff --git a/Documentation/arm/Sharp-LH/LPD7A400 b/Documentation/arm/Sharp-LH/LPD7A400
deleted file mode 100644 (file)
index 3275b45..0000000
+++ /dev/null
@@ -1,15 +0,0 @@
-README on Implementing Linux for the Logic PD LPD7A400-10
-=========================================================
-
-- CPLD memory mapping
-
-  The board designers chose to use high address lines for controlling
-  access to the CPLD registers.  It turns out to be a big waste
-  because we're using an MMU and must map IO space into virtual
-  memory.  The result is that we have to make a mapping for every
-  register.
-
-- Serial Console
-
-  It may be OK not to use the serial console option if the user passes
-  the console device name to the kernel.  This deserves some exploration.
diff --git a/Documentation/arm/Sharp-LH/LPD7A40X b/Documentation/arm/Sharp-LH/LPD7A40X
deleted file mode 100644 (file)
index 8c29a27..0000000
+++ /dev/null
@@ -1,16 +0,0 @@
-README on Implementing Linux for the Logic PD LPD7A40X-10
-=========================================================
-
-- CPLD memory mapping
-
-  The board designers chose to use high address lines for controlling
-  access to the CPLD registers.  It turns out to be a big waste
-  because we're using an MMU and must map IO space into virtual
-  memory.  The result is that we have to make a mapping for every
-  register.
-
-- Serial Console
-
-  It may be OK not to use the serial console option if the user passes
-  the console device name to the kernel.  This deserves some exploration.
-
diff --git a/Documentation/arm/Sharp-LH/SDRAM b/Documentation/arm/Sharp-LH/SDRAM
deleted file mode 100644 (file)
index 93ddc23..0000000
+++ /dev/null
@@ -1,51 +0,0 @@
-README on the SDRAM Controller for the LH7a40X
-==============================================
-
-The standard configuration for the SDRAM controller generates a sparse
-memory array.  The precise layout is determined by the SDRAM chips.  A
-default kernel configuration assembles the discontiguous memory
-regions into separate memory nodes via the NUMA (Non-Uniform Memory
-Architecture) facilities.  In this default configuration, the kernel
-is forgiving about the precise layout.  As long as it is given an
-accurate picture of available memory by the bootloader the kernel will
-execute correctly.
-
-The SDRC supports a mode where some of the chip select lines are
-swapped in order to make SDRAM look like a synchronous ROM.  Setting
-this bit means that the RAM will present as a contiguous array.  Some
-programmers prefer this to the discontiguous layout.  Be aware that
-may be a penalty for this feature where some some configurations of
-memory are significantly reduced; i.e. 64MiB of RAM appears as only 32
-MiB.
-
-There are a couple of configuration options to override the default
-behavior.  When the SROMLL bit is set and memory appears as a
-contiguous array, there is no reason to support NUMA.
-CONFIG_LH7A40X_CONTIGMEM disables NUMA support.  When physical memory
-is discontiguous, the memory tables are organized such that there are
-two banks per nodes with a small gap between them.  This layout wastes
-some kernel memory for page tables representing non-existent memory.
-CONFIG_LH7A40X_ONE_BANK_PER_NODE optimizes the node tables such that
-there are no gaps.  These options control the low level organization
-of the memory management tables in ways that may prevent the kernel
-from booting or may cause the kernel to allocated excessively large
-page tables.  Be warned.  Only change these options if you know what
-you are doing.  The default behavior is a reasonable compromise that
-will suit all users.
-
---
-
-A typical 32MiB system with the default configuration options will
-find physical memory managed as follows.
-
-   node 0: 0xc0000000 4MiB
-           0xc1000000 4MiB
-   node 1: 0xc4000000 4MiB
-           0xc5000000 4MiB
-   node 2: 0xc8000000 4MiB
-           0xc9000000 4MiB
-   node 3: 0xcc000000 4MiB
-           0xcd000000 4MiB
-
-Setting CONFIG_LH7A40X_ONE_BANK_PER_NODE will put each bank into a
-separate node.
diff --git a/Documentation/arm/Sharp-LH/VectoredInterruptController b/Documentation/arm/Sharp-LH/VectoredInterruptController
deleted file mode 100644 (file)
index 23047e9..0000000
+++ /dev/null
@@ -1,80 +0,0 @@
-README on the Vectored Interrupt Controller of the LH7A404
-==========================================================
-
-The 404 revision of the LH7A40X series comes with two vectored
-interrupts controllers.  While the kernel does use some of the
-features of these devices, it is far from the purpose for which they
-were designed.
-
-When this README was written, the implementation of the VICs was in
-flux.  It is possible that some details, especially with priorities,
-will change.
-
-The VIC support code is inspired by routines written by Sharp.
-
-
-Priority Control
-----------------
-
-The significant reason for using the VIC's vectoring is to control
-interrupt priorities.  There are two tables in
-arch/arm/mach-lh7a40x/irq-lh7a404.c that look something like this.
-
-  static unsigned char irq_pri_vic1[] = { IRQ_GPIO3INTR, };
-  static unsigned char irq_pri_vic2[] = {
-       IRQ_T3UI, IRQ_GPIO7INTR,
-       IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR, };
-
-The initialization code reads these tables and inserts a vector
-address and enable for each indicated IRQ.  Vectored interrupts have
-higher priority than non-vectored interrupts.  So, on VIC1,
-IRQ_GPIO3INTR will be served before any other non-FIQ interrupt.  Due
-to the way that the vectoring works, IRQ_T3UI is the next highest
-priority followed by the other vectored interrupts on VIC2.  After
-that, the non-vectored interrupts are scanned in VIC1 then in VIC2.
-
-
-ISR
----
-
-The interrupt service routine macro get_irqnr() in
-arch/arm/kernel/entry-armv.S scans the VICs for the next active
-interrupt.  The vectoring makes this code somewhat larger than it was
-before using vectoring (refer to the LH7A400 implementation).  In the
-case where an interrupt is vectored, the implementation will tend to
-be faster than the non-vectored version.  However, the worst-case path
-is longer.
-
-It is worth noting that at present, there is no need to read
-VIC2_VECTADDR because the register appears to be shared between the
-controllers.  The code is written such that if this changes, it ought
-to still work properly.
-
-
-Vector Addresses
-----------------
-
-The proper use of the vectoring hardware would jump to the ISR
-specified by the vectoring address.  Linux isn't structured to take
-advantage of this feature, though it might be possible to change
-things to support it.
-
-In this implementation, the vectoring address is used to speed the
-search for the active IRQ.  The address is coded such that the lowest
-6 bits store the IRQ number for vectored interrupts.  These numbers
-correspond to the bits in the interrupt status registers.  IRQ zero is
-the lowest interrupt bit in VIC1.  IRQ 32 is the lowest interrupt bit
-in VIC2.  Because zero is a valid IRQ number and because we cannot
-detect whether or not there is a valid vectoring address if that
-address is zero, the eigth bit (0x100) is set for vectored interrupts.
-The address for IRQ 0x18 (VIC2) is 0x118.  Only the ninth bit is set
-for the default handler on VIC1 and only the tenth bit is set for the
-default handler on VIC2.
-
-In other words.
-
-  0x000                - no active interrupt
-  0x1ii                - vectored interrupt 0xii
-  0x2xx                - unvectored interrupt on VIC1 (xx is don't care)
-  0x4xx                - unvectored interrupt on VIC2 (xx is don't care)
-
index 5cff165b7eb04ef092e09957cf05cf6b8eddfcee..18a1eb93fd7237f3356379811dc760e08b215339 100644 (file)
@@ -795,17 +795,6 @@ config ARCH_TCC_926
        help
          Support for Telechips TCC ARM926-based systems.
 
-config ARCH_LH7A40X
-       bool "Sharp LH7A40X"
-       select CPU_ARM922T
-       select ARCH_SPARSEMEM_ENABLE if !LH7A40X_CONTIGMEM
-       select ARCH_USES_GETTIMEOFFSET
-       help
-         Say Y here for systems based on one of the Sharp LH7A40X
-         System on a Chip processors.  These CPUs include an ARM922T
-         core with a wide array of integrated devices for
-         hand-held and low-power applications.
-
 config ARCH_U300
        bool "ST-Ericsson U300 Series"
        depends on MMU
@@ -922,8 +911,6 @@ source "arch/arm/mach-kirkwood/Kconfig"
 
 source "arch/arm/mach-ks8695/Kconfig"
 
-source "arch/arm/mach-lh7a40x/Kconfig"
-
 source "arch/arm/mach-loki/Kconfig"
 
 source "arch/arm/mach-lpc32xx/Kconfig"
index c22c1adfedd6e604bdfa94bf76c598b982666706..aa18cb9da57bcffce1c7c5140b823d1931ddbea7 100644 (file)
@@ -146,7 +146,6 @@ machine-$(CONFIG_ARCH_IXP23XX)              := ixp23xx
 machine-$(CONFIG_ARCH_IXP4XX)          := ixp4xx
 machine-$(CONFIG_ARCH_KIRKWOOD)                := kirkwood
 machine-$(CONFIG_ARCH_KS8695)          := ks8695
-machine-$(CONFIG_ARCH_LH7A40X)         := lh7a40x
 machine-$(CONFIG_ARCH_LOKI)            := loki
 machine-$(CONFIG_ARCH_LPC32XX)         := lpc32xx
 machine-$(CONFIG_ARCH_MMP)             := mmp
diff --git a/arch/arm/configs/lpd7a400_defconfig b/arch/arm/configs/lpd7a400_defconfig
deleted file mode 100644 (file)
index 5a48f17..0000000
+++ /dev/null
@@ -1,68 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-# CONFIG_HOTPLUG is not set
-# CONFIG_EPOLL is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-CONFIG_ARCH_LH7A40X=y
-CONFIG_MACH_LPD7A400=y
-CONFIG_PREEMPT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_FPE_NWFPE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_IDE=y
-CONFIG_SCSI=y
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_LH7A40X=y
-CONFIG_SERIAL_LH7A40X_CONSOLE=y
-CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig
deleted file mode 100644 (file)
index 22d0631..0000000
+++ /dev/null
@@ -1,81 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_LOG_BUF_SHIFT=16
-CONFIG_EXPERT=y
-# CONFIG_HOTPLUG is not set
-# CONFIG_EPOLL is not set
-CONFIG_SLAB=y
-# CONFIG_IOSCHED_DEADLINE is not set
-CONFIG_ARCH_LH7A40X=y
-CONFIG_MACH_LPD7A404=y
-CONFIG_PREEMPT=y
-CONFIG_DISCONTIGMEM_MANUAL=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_FPE_NWFPE=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_IDE=y
-CONFIG_SCSI=y
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_LH7A40X=y
-CONFIG_SERIAL_LH7A40X_CONSOLE=y
-CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DEBUG=y
-CONFIG_USB_STORAGE_DATAFAB=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ZERO=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_INOTIFY=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
index f1e5a9bca2491d982bda9fda1d40aa7b63b0cfd8..da8b52ec49cf43c433712ecff099cf0d7a9d8cfd 100644 (file)
@@ -192,11 +192,7 @@ static struct tagtable __tagtable_##fn __tag = { tag, fn }
 /*
  * Memory map description
  */
-#ifdef CONFIG_ARCH_LH7A40X
-# define NR_BANKS 16
-#else
-# define NR_BANKS 8
-#endif
+#define NR_BANKS 8
 
 struct membank {
        unsigned long start;
diff --git a/arch/arm/mach-lh7a40x/Kconfig b/arch/arm/mach-lh7a40x/Kconfig
deleted file mode 100644 (file)
index 9be7466..0000000
+++ /dev/null
@@ -1,74 +0,0 @@
-if ARCH_LH7A40X
-
-menu "LH7A40X Implementations"
-
-config MACH_KEV7A400
-       bool "KEV7A400"
-       select ARCH_LH7A400
-       help
-         Say Y here if you are using the Sharp KEV7A400 development
-         board.  This hardware is discontinued, so I'd be very
-         surprised if you wanted this option.
-
-config MACH_LPD7A400
-       bool "LPD7A400 Card Engine"
-       select ARCH_LH7A400
-#      select IDE_POLL
-#      select HAS_TOUCHSCREEN_ADS7843_LH7
-       help
-         Say Y here if you are using Logic Product Development's
-         LPD7A400 CardEngine.  For the time being, the LPD7A400 and
-         LPD7A404 options are mutually exclusive.
-
-config MACH_LPD7A404
-       bool "LPD7A404 Card Engine"
-       select ARCH_LH7A404
-#      select IDE_POLL
-#      select HAS_TOUCHSCREEN_ADC_LH7
-       help
-         Say Y here if you are using Logic Product Development's
-         LPD7A404 CardEngine. For the time being, the LPD7A400 and
-         LPD7A404 options are mutually exclusive.
-
-config ARCH_LH7A400
-       bool
-
-config ARCH_LH7A404
-       bool
-
-config LPD7A40X_CPLD_SSP
-       bool
-
-config LH7A40X_CONTIGMEM
-       bool "Disable NUMA/SparseMEM Support"
-       help
-         Say Y here if your bootloader sets the SROMLL bit(s) in
-         the SDRAM controller, organizing memory as a contiguous
-         array.  This option will disable sparse memory support
-          and force the kernel to manage all memory in one node.
-
-         Setting this option incorrectly may prevent the kernel
-         from booting.  It is OK to leave it N.
-
-         For more information, consult
-           <file:Documentation/arm/Sharp-LH/SDRAM>.
-
-config LH7A40X_ONE_BANK_PER_NODE
-       bool "Optimize NUMA Node Tables for Size"
-       depends on !LH7A40X_CONTIGMEM
-       help
-         Say Y here to produce compact memory node tables.  By
-         default pairs of adjacent physical RAM banks are managed
-         together in a single node, incurring some wasted overhead
-         in the node tables, however also maintaining compatibility
-         with systems where physical memory is truly contiguous.
-
-         Setting this option incorrectly may prevent the kernel from
-         booting.  It is OK to leave it N.
-
-         For more information, consult
-           <file:Documentation/arm/Sharp-LH/SDRAM>.
-
-endmenu
-
-endif
diff --git a/arch/arm/mach-lh7a40x/Makefile b/arch/arm/mach-lh7a40x/Makefile
deleted file mode 100644 (file)
index 94b8615..0000000
+++ /dev/null
@@ -1,17 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-
-# Object file lists.
-
-obj-y                          := time.o clocks.o
-obj-m                          :=
-obj-n                          :=
-obj-                           :=
-
-obj-$(CONFIG_MACH_KEV7A400)    += arch-kev7a400.o irq-lh7a400.o
-obj-$(CONFIG_MACH_LPD7A400)    += arch-lpd7a40x.o irq-lh7a400.o
-obj-$(CONFIG_MACH_LPD7A404)    += arch-lpd7a40x.o irq-lh7a404.o
-obj-$(CONFIG_LPD7A40X_CPLD_SSP)        += ssp-cpld.o
-obj-$(CONFIG_FB_ARMCLCD)       += clcd.o
-
diff --git a/arch/arm/mach-lh7a40x/Makefile.boot b/arch/arm/mach-lh7a40x/Makefile.boot
deleted file mode 100644 (file)
index af941be..0000000
+++ /dev/null
@@ -1,4 +0,0 @@
-   zreladdr-y  := 0xc0008000
-params_phys-y  := 0xc0000100
-initrd_phys-y  := 0xc4000000
-
diff --git a/arch/arm/mach-lh7a40x/arch-kev7a400.c b/arch/arm/mach-lh7a40x/arch-kev7a400.c
deleted file mode 100644 (file)
index 71129c3..0000000
+++ /dev/null
@@ -1,118 +0,0 @@
-/* arch/arm/mach-lh7a40x/arch-kev7a400.c
- *
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/tty.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-
-      /* This function calls the board specific IRQ initialization function. */
-
-static struct map_desc kev7a400_io_desc[] __initdata = {
-       {
-               .virtual        = IO_VIRT,
-               .pfn            = __phys_to_pfn(IO_PHYS),
-               .length         = IO_SIZE,
-               .type           = MT_DEVICE
-       }, {
-               .virtual        = CPLD_VIRT,
-               .pfn            = __phys_to_pfn(CPLD_PHYS),
-               .length         = CPLD_SIZE,
-               .type           = MT_DEVICE
-       }
-};
-
-void __init kev7a400_map_io(void)
-{
-       iotable_init (kev7a400_io_desc, ARRAY_SIZE (kev7a400_io_desc));
-}
-
-static u16 CPLD_IRQ_mask;      /* Mask for CPLD IRQs, 1 == unmasked */
-
-static void kev7a400_ack_cpld_irq(struct irq_data *d)
-{
-       CPLD_CL_INT = 1 << (d->irq - IRQ_KEV7A400_CPLD);
-}
-
-static void kev7a400_mask_cpld_irq(struct irq_data *d)
-{
-       CPLD_IRQ_mask &= ~(1 << (d->irq - IRQ_KEV7A400_CPLD));
-       CPLD_WR_PB_INT_MASK = CPLD_IRQ_mask;
-}
-
-static void kev7a400_unmask_cpld_irq(struct irq_data *d)
-{
-       CPLD_IRQ_mask |= 1 << (d->irq - IRQ_KEV7A400_CPLD);
-       CPLD_WR_PB_INT_MASK = CPLD_IRQ_mask;
-}
-
-static struct irq_chip kev7a400_cpld_chip = {
-       .name           = "CPLD",
-       .irq_ack        = kev7a400_ack_cpld_irq,
-       .irq_mask       = kev7a400_mask_cpld_irq,
-       .irq_unmask     = kev7a400_unmask_cpld_irq,
-};
-
-
-static void kev7a400_cpld_handler (unsigned int irq, struct irq_desc *desc)
-{
-       u32 mask = CPLD_LATCHED_INTS;
-       irq = IRQ_KEV7A400_CPLD;
-       for (; mask; mask >>= 1, ++irq)
-               if (mask & 1)
-                       generic_handle_irq(irq);
-}
-
-void __init lh7a40x_init_board_irq (void)
-{
-       int irq;
-
-       for (irq = IRQ_KEV7A400_CPLD;
-            irq < IRQ_KEV7A400_CPLD + NR_IRQ_BOARD; ++irq) {
-               set_irq_chip (irq, &kev7a400_cpld_chip);
-               set_irq_handler (irq, handle_edge_irq);
-               set_irq_flags (irq, IRQF_VALID);
-       }
-       set_irq_chained_handler (IRQ_CPLD, kev7a400_cpld_handler);
-
-               /* Clear all CPLD interrupts */
-       CPLD_CL_INT = 0xff; /* CPLD_INTR_MMC_CD | CPLD_INTR_ETH_INT; */
-
-       GPIO_GPIOINTEN = 0;             /* Disable all GPIO interrupts */
-       barrier();
-
-#if 0
-       GPIO_INTTYPE1
-               = (GPIO_INTR_PCC1_CD | GPIO_INTR_PCC1_CD); /* Edge trig. */
-       GPIO_INTTYPE2 = 0;              /* Falling edge & low-level */
-       GPIO_GPIOFEOI = 0xff;           /* Clear all GPIO interrupts */
-       GPIO_GPIOINTEN = 0xff;          /* Enable all GPIO interrupts */
-
-       init_FIQ();
-#endif
-}
-
-MACHINE_START (KEV7A400, "Sharp KEV7a400")
-       /* Maintainer: Marc Singer */
-       .boot_params    = 0xc0000100,
-       .map_io         = kev7a400_map_io,
-       .init_irq       = lh7a400_init_irq,
-       .timer          = &lh7a40x_timer,
-MACHINE_END
diff --git a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c
deleted file mode 100644 (file)
index e735546..0000000
+++ /dev/null
@@ -1,422 +0,0 @@
-/* arch/arm/mach-lh7a40x/arch-lpd7a40x.c
- *
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/tty.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-
-#define CPLD_INT_NETHERNET     (1<<0)
-#define CPLD_INTMASK_ETHERNET  (1<<2)
-#if defined (CONFIG_MACH_LPD7A400)
-# define CPLD_INT_NTOUCH               (1<<1)
-# define CPLD_INTMASK_TOUCH    (1<<3)
-# define CPLD_INT_PEN          (1<<4)
-# define CPLD_INTMASK_PEN      (1<<4)
-# define CPLD_INT_PIRQ         (1<<4)
-#endif
-#define CPLD_INTMASK_CPLD      (1<<7)
-#define CPLD_INT_CPLD          (1<<6)
-
-#define CPLD_CONTROL_SWINT             (1<<7) /* Disable all CPLD IRQs */
-#define CPLD_CONTROL_OCMSK             (1<<6) /* Mask USB1 connect IRQ */
-#define CPLD_CONTROL_PDRV              (1<<5) /* PCC_nDRV high */
-#define CPLD_CONTROL_USB1C             (1<<4) /* USB1 connect IRQ active */
-#define CPLD_CONTROL_USB1P             (1<<3) /* USB1 power disable */
-#define CPLD_CONTROL_AWKP              (1<<2) /* Auto-wakeup disabled  */
-#define CPLD_CONTROL_LCD_ENABLE                (1<<1) /* LCD Vee enable */
-#define CPLD_CONTROL_WRLAN_NENABLE     (1<<0) /* SMC91x power disable */
-
-
-static struct resource smc91x_resources[] = {
-       [0] = {
-               .start  = CPLD00_PHYS,
-               .end    = CPLD00_PHYS + CPLD00_SIZE - 1, /* Only needs 16B */
-               .flags  = IORESOURCE_MEM,
-       },
-
-       [1] = {
-               .start  = IRQ_LPD7A40X_ETH_INT,
-               .end    = IRQ_LPD7A40X_ETH_INT,
-               .flags  = IORESOURCE_IRQ,
-       },
-
-};
-
-static struct platform_device smc91x_device = {
-       .name           = "smc91x",
-       .id             = 0,
-       .num_resources  = ARRAY_SIZE(smc91x_resources),
-       .resource       = smc91x_resources,
-};
-
-static struct resource lh7a40x_usbclient_resources[] = {
-       [0] = {
-               .start  = USB_PHYS,
-               .end    = (USB_PHYS + PAGE_SIZE),
-               .flags  = IORESOURCE_MEM,
-       },
-       [1] = {
-               .start  = IRQ_USB,
-               .end    = IRQ_USB,
-               .flags  = IORESOURCE_IRQ,
-       },
-};
-
-static u64 lh7a40x_usbclient_dma_mask = 0xffffffffUL;
-
-static struct platform_device lh7a40x_usbclient_device = {
-//     .name           = "lh7a40x_udc",
-       .name           = "lh7-udc",
-       .id             = 0,
-       .dev            = {
-               .dma_mask = &lh7a40x_usbclient_dma_mask,
-               .coherent_dma_mask = 0xffffffffUL,
-       },
-       .num_resources  = ARRAY_SIZE (lh7a40x_usbclient_resources),
-       .resource       = lh7a40x_usbclient_resources,
-};
-
-#if defined (CONFIG_ARCH_LH7A404)
-
-static struct resource lh7a404_usbhost_resources [] = {
-       [0] = {
-               .start  = USBH_PHYS,
-               .end    = (USBH_PHYS + 0xFF),
-               .flags  = IORESOURCE_MEM,
-       },
-       [1] = {
-               .start  = IRQ_USHINTR,
-               .end    = IRQ_USHINTR,
-               .flags  = IORESOURCE_IRQ,
-       },
-};
-
-static u64 lh7a404_usbhost_dma_mask = 0xffffffffUL;
-
-static struct platform_device lh7a404_usbhost_device = {
-       .name           = "lh7a404-ohci",
-       .id             = 0,
-       .dev            = {
-               .dma_mask = &lh7a404_usbhost_dma_mask,
-               .coherent_dma_mask = 0xffffffffUL,
-       },
-       .num_resources  = ARRAY_SIZE (lh7a404_usbhost_resources),
-       .resource       = lh7a404_usbhost_resources,
-};
-
-#endif
-
-static struct platform_device* lpd7a40x_devs[] __initdata = {
-       &smc91x_device,
-       &lh7a40x_usbclient_device,
-#if defined (CONFIG_ARCH_LH7A404)
-       &lh7a404_usbhost_device,
-#endif
-};
-
-extern void lpd7a400_map_io (void);
-
-static void __init lpd7a40x_init (void)
-{
-#if defined (CONFIG_MACH_LPD7A400)
-       CPLD_CONTROL |= 0
-               | CPLD_CONTROL_SWINT /* Disable software interrupt */
-               | CPLD_CONTROL_OCMSK; /* Mask USB1 connection IRQ */
-       CPLD_CONTROL &= ~(0
-                         | CPLD_CONTROL_LCD_ENABLE     /* Disable LCD */
-                         | CPLD_CONTROL_WRLAN_NENABLE  /* Enable SMC91x */
-               );
-#endif
-
-#if defined (CONFIG_MACH_LPD7A404)
-       CPLD_CONTROL &= ~(0
-                         | CPLD_CONTROL_WRLAN_NENABLE  /* Enable SMC91x */
-               );
-#endif
-
-       platform_add_devices (lpd7a40x_devs, ARRAY_SIZE (lpd7a40x_devs));
-#if defined (CONFIG_FB_ARMCLCD)
-        lh7a40x_clcd_init ();
-#endif
-}
-
-static void lh7a40x_ack_cpld_irq(struct irq_data *d)
-{
-       /* CPLD doesn't have ack capability, but some devices may */
-
-#if defined (CPLD_INTMASK_TOUCH)
-       /* The touch control *must* mask the interrupt because the
-        * interrupt bit is read by the driver to determine if the pen
-        * is still down. */
-       if (d->irq == IRQ_TOUCH)
-               CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH;
-#endif
-}
-
-static void lh7a40x_mask_cpld_irq(struct irq_data *d)
-{
-       switch (d->irq) {
-       case IRQ_LPD7A40X_ETH_INT:
-               CPLD_INTERRUPTS |= CPLD_INTMASK_ETHERNET;
-               break;
-#if defined (IRQ_TOUCH)
-       case IRQ_TOUCH:
-               CPLD_INTERRUPTS |= CPLD_INTMASK_TOUCH;
-               break;
-#endif
-       }
-}
-
-static void lh7a40x_unmask_cpld_irq(struct irq_data *d)
-{
-       switch (d->irq) {
-       case IRQ_LPD7A40X_ETH_INT:
-               CPLD_INTERRUPTS &= ~CPLD_INTMASK_ETHERNET;
-               break;
-#if defined (IRQ_TOUCH)
-       case IRQ_TOUCH:
-               CPLD_INTERRUPTS &= ~CPLD_INTMASK_TOUCH;
-               break;
-#endif
-       }
-}
-
-static struct irq_chip lpd7a40x_cpld_chip = {
-       .name           = "CPLD",
-       .irq_ack        = lh7a40x_ack_cpld_irq,
-       .irq_mask       = lh7a40x_mask_cpld_irq,
-       .irq_unmask     = lh7a40x_unmask_cpld_irq,
-};
-
-static void lpd7a40x_cpld_handler (unsigned int irq, struct irq_desc *desc)
-{
-       unsigned int mask = CPLD_INTERRUPTS;
-
-       desc->irq_data.chip->irq_ack(&desc->irq_data);
-
-       if ((mask & (1<<0)) == 0)       /* WLAN */
-               generic_handle_irq(IRQ_LPD7A40X_ETH_INT);
-
-#if defined (IRQ_TOUCH)
-       if ((mask & (1<<1)) == 0)       /* Touch */
-               generic_handle_irq(IRQ_TOUCH);
-#endif
-
-       /* Level-triggered need this */
-       desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-
-void __init lh7a40x_init_board_irq (void)
-{
-       int irq;
-
-               /* Rev A (v2.8): PF0, PF1, PF2, and PF3 are available IRQs.
-                                PF7 supports the CPLD.
-                  Rev B (v3.4): PF0, PF1, and PF2 are available IRQs.
-                                PF3 supports the CPLD.
-                  (Some) LPD7A404 prerelease boards report a version
-                  number of 0x16, but we force an override since the
-                  hardware is of the newer variety.
-               */
-
-       unsigned char cpld_version = CPLD_REVISION;
-       int pinCPLD = (cpld_version == 0x28) ? 7 : 3;
-
-#if defined CONFIG_MACH_LPD7A404
-       cpld_version = 0x34;    /* Coerce LPD7A404 to RevB */
-#endif
-
-               /* First, configure user controlled GPIOF interrupts  */
-
-       GPIO_PFDD       &= ~0x0f; /* PF0-3 are inputs */
-       GPIO_INTTYPE1   &= ~0x0f; /* PF0-3 are level triggered */
-       GPIO_INTTYPE2   &= ~0x0f; /* PF0-3 are active low */
-       barrier ();
-       GPIO_GPIOFINTEN |=  0x0f; /* Enable PF0, PF1, PF2, and PF3 IRQs */
-
-               /* Then, configure CPLD interrupt */
-
-                       /* Disable all CPLD interrupts */
-#if defined (CONFIG_MACH_LPD7A400)
-       CPLD_INTERRUPTS = CPLD_INTMASK_TOUCH | CPLD_INTMASK_PEN
-               | CPLD_INTMASK_ETHERNET;
-       /* *** FIXME: don't know why we need 7 and 4. 7 is way wrong
-               and 4 is uncefined. */
-       // (1<<7)|(1<<4)|(1<<3)|(1<<2);
-#endif
-#if defined (CONFIG_MACH_LPD7A404)
-       CPLD_INTERRUPTS = CPLD_INTMASK_ETHERNET;
-       /* *** FIXME: don't know why we need 6 and 5, neither is defined. */
-       // (1<<6)|(1<<5)|(1<<3);
-#endif
-       GPIO_PFDD       &= ~(1 << pinCPLD); /* Make input */
-       GPIO_INTTYPE1   &= ~(1 << pinCPLD); /* Level triggered */
-       GPIO_INTTYPE2   &= ~(1 << pinCPLD); /* Active low */
-       barrier ();
-       GPIO_GPIOFINTEN |=  (1 << pinCPLD); /* Enable */
-
-               /* Cascade CPLD interrupts */
-
-       for (irq = IRQ_BOARD_START;
-            irq < IRQ_BOARD_START + NR_IRQ_BOARD; ++irq) {
-               set_irq_chip (irq, &lpd7a40x_cpld_chip);
-               set_irq_handler (irq, handle_level_irq);
-               set_irq_flags (irq, IRQF_VALID);
-       }
-
-       set_irq_chained_handler ((cpld_version == 0x28)
-                                ? IRQ_CPLD_V28
-                                : IRQ_CPLD_V34,
-                                lpd7a40x_cpld_handler);
-}
-
-static struct map_desc lpd7a40x_io_desc[] __initdata = {
-       {
-               .virtual        = IO_VIRT,
-               .pfn            = __phys_to_pfn(IO_PHYS),
-               .length         = IO_SIZE,
-               .type           = MT_DEVICE
-       },
-       {       /* Mapping added to work around chip select problems */
-               .virtual        = IOBARRIER_VIRT,
-               .pfn            = __phys_to_pfn(IOBARRIER_PHYS),
-               .length         = IOBARRIER_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CF_VIRT,
-               .pfn            = __phys_to_pfn(CF_PHYS),
-               .length         = CF_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD02_VIRT,
-               .pfn            = __phys_to_pfn(CPLD02_PHYS),
-               .length         = CPLD02_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD06_VIRT,
-               .pfn            = __phys_to_pfn(CPLD06_PHYS),
-               .length         = CPLD06_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD08_VIRT,
-               .pfn            = __phys_to_pfn(CPLD08_PHYS),
-               .length         = CPLD08_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD08_VIRT,
-               .pfn            = __phys_to_pfn(CPLD08_PHYS),
-               .length         = CPLD08_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD0A_VIRT,
-               .pfn            = __phys_to_pfn(CPLD0A_PHYS),
-               .length         = CPLD0A_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD0C_VIRT,
-               .pfn            = __phys_to_pfn(CPLD0C_PHYS),
-               .length         = CPLD0C_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD0E_VIRT,
-               .pfn            = __phys_to_pfn(CPLD0E_PHYS),
-               .length         = CPLD0E_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD10_VIRT,
-               .pfn            = __phys_to_pfn(CPLD10_PHYS),
-               .length         = CPLD10_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD12_VIRT,
-               .pfn            = __phys_to_pfn(CPLD12_PHYS),
-               .length         = CPLD12_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD14_VIRT,
-               .pfn            = __phys_to_pfn(CPLD14_PHYS),
-               .length         = CPLD14_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD16_VIRT,
-               .pfn            = __phys_to_pfn(CPLD16_PHYS),
-               .length         = CPLD16_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD18_VIRT,
-               .pfn            = __phys_to_pfn(CPLD18_PHYS),
-               .length         = CPLD18_SIZE,
-               .type           = MT_DEVICE
-       },
-       {
-               .virtual        = CPLD1A_VIRT,
-               .pfn            = __phys_to_pfn(CPLD1A_PHYS),
-               .length         = CPLD1A_SIZE,
-               .type           = MT_DEVICE
-       },
-};
-
-void __init
-lpd7a40x_map_io(void)
-{
-       iotable_init (lpd7a40x_io_desc, ARRAY_SIZE (lpd7a40x_io_desc));
-}
-
-#ifdef CONFIG_MACH_LPD7A400
-
-MACHINE_START (LPD7A400, "Logic Product Development LPD7A400-10")
-       /* Maintainer: Marc Singer */
-       .boot_params    = 0xc0000100,
-       .map_io         = lpd7a40x_map_io,
-       .init_irq       = lh7a400_init_irq,
-       .timer          = &lh7a40x_timer,
-       .init_machine   = lpd7a40x_init,
-MACHINE_END
-
-#endif
-
-#ifdef CONFIG_MACH_LPD7A404
-
-MACHINE_START (LPD7A404, "Logic Product Development LPD7A404-10")
-       /* Maintainer: Marc Singer */
-       .boot_params    = 0xc0000100,
-       .map_io         = lpd7a40x_map_io,
-       .init_irq       = lh7a404_init_irq,
-       .timer          = &lh7a40x_timer,
-       .init_machine   = lpd7a40x_init,
-MACHINE_END
-
-#endif
diff --git a/arch/arm/mach-lh7a40x/clcd.c b/arch/arm/mach-lh7a40x/clcd.c
deleted file mode 100644 (file)
index 7fe4fd3..0000000
+++ /dev/null
@@ -1,241 +0,0 @@
-/*
- *  arch/arm/mach-lh7a40x/clcd.c
- *
- *  Copyright (C) 2004 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/gfp.h>
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-#include <linux/sysdev.h>
-#include <linux/interrupt.h>
-
-//#include <linux/module.h>
-//#include <linux/time.h>
-
-//#include <asm/mach/time.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-
-#include <asm/system.h>
-#include <mach/hardware.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/clcd.h>
-
-#define HRTFTC_HRSETUP         __REG(HRTFTC_PHYS + 0x00)
-#define HRTFTC_HRCON           __REG(HRTFTC_PHYS + 0x04)
-#define HRTFTC_HRTIMING1       __REG(HRTFTC_PHYS + 0x08)
-#define HRTFTC_HRTIMING2       __REG(HRTFTC_PHYS + 0x0c)
-
-#define ALI_SETUP              __REG(ALI_PHYS + 0x00)
-#define ALI_CONTROL            __REG(ALI_PHYS + 0x04)
-#define ALI_TIMING1            __REG(ALI_PHYS + 0x08)
-#define ALI_TIMING2            __REG(ALI_PHYS + 0x0c)
-
-#include "lcd-panel.h"
-
-static void lh7a40x_clcd_disable (struct clcd_fb *fb)
-{
-#if defined (CONFIG_MACH_LPD7A400)
-       CPLD_CONTROL &= ~(1<<1);        /* Disable LCD Vee */
-#endif
-
-#if defined (CONFIG_MACH_LPD7A404)
-       GPIO_PCD  &= ~(1<<3);           /* Disable LCD Vee */
-#endif
-
-#if defined (CONFIG_ARCH_LH7A400)
-       HRTFTC_HRSETUP &= ~(1<<13);     /* Disable HRTFT controller */
-#endif
-
-#if defined (CONFIG_ARCH_LH7A404)
-       ALI_SETUP &= ~(1<<13);          /* Disable ALI */
-#endif
-}
-
-static void lh7a40x_clcd_enable (struct clcd_fb *fb)
-{
-       struct clcd_panel_extra* extra
-               = (struct clcd_panel_extra*) fb->board_data;
-
-#if defined (CONFIG_MACH_LPD7A400)
-       CPLD_CONTROL |= (1<<1);         /* Enable LCD Vee */
-#endif
-
-#if defined (CONFIG_MACH_LPD7A404)
-       GPIO_PCDD &= ~(1<<3);           /* Enable LCD Vee */
-       GPIO_PCD  |=  (1<<3);
-#endif
-
-#if defined (CONFIG_ARCH_LH7A400)
-
-       if (extra) {
-               HRTFTC_HRSETUP
-                       = (1 << 13)
-                       | ((fb->fb.var.xres - 1) << 4)
-                       | 0xc
-                       | (extra->hrmode ? 1 : 0);
-               HRTFTC_HRCON
-                       = ((extra->clsen ? 1 : 0) << 1)
-                       | ((extra->spsen ? 1 : 0) << 0);
-               HRTFTC_HRTIMING1
-                       = (extra->pcdel << 8)
-                       | (extra->revdel << 4)
-                       | (extra->lpdel << 0);
-               HRTFTC_HRTIMING2
-                       = (extra->spldel << 9)
-                       | (extra->pc2del << 0);
-       }
-       else
-               HRTFTC_HRSETUP
-                       = (1 << 13)
-                       | 0xc;
-#endif
-
-#if defined (CONFIG_ARCH_LH7A404)
-
-       if (extra) {
-               ALI_SETUP
-                       = (1 << 13)
-                       | ((fb->fb.var.xres - 1) << 4)
-                       | 0xc
-                       | (extra->hrmode ? 1 : 0);
-               ALI_CONTROL
-                       = ((extra->clsen ? 1 : 0) << 1)
-                       | ((extra->spsen ? 1 : 0) << 0);
-               ALI_TIMING1
-                       = (extra->pcdel << 8)
-                       | (extra->revdel << 4)
-                       | (extra->lpdel << 0);
-               ALI_TIMING2
-                       = (extra->spldel << 9)
-                       | (extra->pc2del << 0);
-       }
-       else
-               ALI_SETUP
-                       = (1 << 13)
-                       | 0xc;
-#endif
-
-}
-
-#define FRAMESIZE(s) (((s) + PAGE_SIZE - 1)&PAGE_MASK)
-
-static int lh7a40x_clcd_setup (struct clcd_fb *fb)
-{
-       dma_addr_t dma;
-       u32 len = FRAMESIZE (lcd_panel.mode.xres*lcd_panel.mode.yres
-                            *(lcd_panel.bpp/8));
-
-       fb->panel = &lcd_panel;
-
-               /* Enforce the sync polarity defaults */
-       if (!(fb->panel->tim2 & TIM2_IHS))
-               fb->fb.var.sync |= FB_SYNC_HOR_HIGH_ACT;
-       if (!(fb->panel->tim2 & TIM2_IVS))
-               fb->fb.var.sync |= FB_SYNC_VERT_HIGH_ACT;
-
-#if defined (HAS_LCD_PANEL_EXTRA)
-       fb->board_data = &lcd_panel_extra;
-#endif
-
-       fb->fb.screen_base
-               = dma_alloc_writecombine (&fb->dev->dev, len,
-                                         &dma, GFP_KERNEL);
-       printk ("CLCD: LCD setup fb virt 0x%p phys 0x%p l %x io 0x%p \n",
-               fb->fb.screen_base, (void*) dma, len,
-               (void*) io_p2v (CLCDC_PHYS));
-       printk ("CLCD: pixclock %d\n", lcd_panel.mode.pixclock);
-
-       if (!fb->fb.screen_base) {
-               printk(KERN_ERR "CLCD: unable to map framebuffer\n");
-               return -ENOMEM;
-       }
-
-#if defined (USE_RGB555)
-       fb->fb.var.green.length = 5; /* Panel uses RGB 5:5:5 */
-#endif
-
-       fb->fb.fix.smem_start = dma;
-       fb->fb.fix.smem_len = len;
-
-               /* Drive PE4 high to prevent CPLD crash */
-       GPIO_PEDD |= (1<<4);
-       GPIO_PED  |= (1<<4);
-
-       GPIO_PINMUX |= (1<<1) | (1<<0); /* LCDVD[15:4] */
-
-//     fb->fb.fbops->fb_check_var (&fb->fb.var, &fb->fb);
-//     fb->fb.fbops->fb_set_par (&fb->fb);
-
-       return 0;
-}
-
-static int lh7a40x_clcd_mmap (struct clcd_fb *fb, struct vm_area_struct *vma)
-{
-       return dma_mmap_writecombine(&fb->dev->dev, vma,
-                                    fb->fb.screen_base,
-                                    fb->fb.fix.smem_start,
-                                    fb->fb.fix.smem_len);
-}
-
-static void lh7a40x_clcd_remove (struct clcd_fb *fb)
-{
-       dma_free_writecombine (&fb->dev->dev, fb->fb.fix.smem_len,
-                              fb->fb.screen_base, fb->fb.fix.smem_start);
-}
-
-static struct clcd_board clcd_platform_data = {
-       .name           = "lh7a40x FB",
-       .check          = clcdfb_check,
-       .decode         = clcdfb_decode,
-       .enable         = lh7a40x_clcd_enable,
-       .setup          = lh7a40x_clcd_setup,
-       .mmap           = lh7a40x_clcd_mmap,
-       .remove         = lh7a40x_clcd_remove,
-       .disable        = lh7a40x_clcd_disable,
-};
-
-#define IRQ_CLCDC (IRQ_LCDINTR)
-
-#define AMBA_DEVICE(name,busid,base,plat,pid)                  \
-static struct amba_device name##_device = {                    \
-       .dev = {                                                \
-               .coherent_dma_mask = ~0,                        \
-               .init_name = busid,                             \
-               .platform_data = plat,                          \
-               },                                              \
-       .res = {                                                \
-               .start  = base##_PHYS,                          \
-               .end    = (base##_PHYS) + (4*1024) - 1,         \
-               .flags  = IORESOURCE_MEM,                       \
-               },                                              \
-       .dma_mask       = ~0,                                   \
-       .irq            = { IRQ_##base, },                      \
-       /* .dma         = base##_DMA,*/                         \
-       .periphid = pid,                                        \
-}
-
-AMBA_DEVICE(clcd,  "cldc-lh7a40x",  CLCDC,     &clcd_platform_data, 0x41110);
-
-static struct amba_device *amba_devs[] __initdata = {
-       &clcd_device,
-};
-
-void __init lh7a40x_clcd_init (void)
-{
-       int i;
-       int result;
-       printk ("CLCD: registering amba devices\n");
-       for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
-               struct amba_device *d = amba_devs[i];
-               result = amba_device_register(d, &iomem_resource);
-               printk ("  %d -> %d\n", i ,result);
-       }
-}
diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c
deleted file mode 100644 (file)
index 0651f96..0000000
+++ /dev/null
@@ -1,108 +0,0 @@
-/* arch/arm/mach-lh7a40x/clocks.c
- *
- *  Copyright (C) 2004 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-#include <mach/hardware.h>
-#include <mach/clocks.h>
-#include <linux/err.h>
-#include <linux/device.h>
-#include <linux/string.h>
-
-struct module;
-
-struct clk {
-       struct list_head node;
-       unsigned long rate;
-       struct module *owner;
-       const char *name;
-};
-
-/* ----- */
-
-#define MAINDIV1(c)    (((c) >>  7) & 0x0f)
-#define MAINDIV2(c)    (((c) >> 11) & 0x1f)
-#define PS(c)          (((c) >> 18) & 0x03)
-#define PREDIV(c)      (((c) >>  2) & 0x1f)
-#define HCLKDIV(c)     (((c) >>  0) & 0x02)
-#define PCLKDIV(c)     (((c) >> 16) & 0x03)
-
-unsigned int fclkfreq_get (void)
-{
-       unsigned int clkset = CSC_CLKSET;
-       unsigned int gclk
-               = XTAL_IN
-               / (1 << PS(clkset))
-               * (MAINDIV1(clkset) + 2)
-               / (PREDIV(clkset)   + 2)
-               * (MAINDIV2(clkset) + 2)
-               ;
-       return gclk;
-}
-
-unsigned int hclkfreq_get (void)
-{
-       unsigned int clkset = CSC_CLKSET;
-       unsigned int hclk = fclkfreq_get () / (HCLKDIV(clkset) + 1);
-
-       return hclk;
-}
-
-unsigned int pclkfreq_get (void)
-{
-       unsigned int clkset = CSC_CLKSET;
-       int pclkdiv = PCLKDIV(clkset);
-       unsigned int pclk;
-       if (pclkdiv == 0x3)
-               pclkdiv = 0x2;
-       pclk = hclkfreq_get () / (1 << pclkdiv);
-
-       return pclk;
-}
-
-/* ----- */
-
-struct clk *clk_get (struct device *dev, const char *id)
-{
-       return dev && strcmp(dev_name(dev), "cldc-lh7a40x") == 0
-                ? NULL : ERR_PTR(-ENOENT);
-}
-EXPORT_SYMBOL(clk_get);
-
-void clk_put (struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_put);
-
-int clk_enable (struct clk *clk)
-{
-       return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable (struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_disable);
-
-unsigned long clk_get_rate (struct clk *clk)
-{
-       return 0;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-long clk_round_rate (struct clk *clk, unsigned long rate)
-{
-       return rate;
-}
-EXPORT_SYMBOL(clk_round_rate);
-
-int clk_set_rate (struct clk *clk, unsigned long rate)
-{
-       return -EIO;
-}
-EXPORT_SYMBOL(clk_set_rate);
diff --git a/arch/arm/mach-lh7a40x/common.h b/arch/arm/mach-lh7a40x/common.h
deleted file mode 100644 (file)
index 6ed3f6b..0000000
+++ /dev/null
@@ -1,17 +0,0 @@
-/* arch/arm/mach-lh7a40x/common.h
- *
- *  Copyright (C) 2004 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-extern struct sys_timer lh7a40x_timer;
-
-extern void lh7a400_init_irq (void);
-extern void lh7a404_init_irq (void);
-extern void lh7a40x_clcd_init (void);
-extern void lh7a40x_init_board_irq (void);
-
diff --git a/arch/arm/mach-lh7a40x/include/mach/clocks.h b/arch/arm/mach-lh7a40x/include/mach/clocks.h
deleted file mode 100644 (file)
index fe2e025..0000000
+++ /dev/null
@@ -1,18 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/clocks.h
- *
- *  Copyright (C) 2004 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#ifndef __ASM_ARCH_CLOCKS_H
-#define __ASM_ARCH_CLOCKS_H
-
-unsigned int fclkfreq_get (void);
-unsigned int hclkfreq_get (void);
-unsigned int pclkfreq_get (void);
-
-#endif  /* _ASM_ARCH_CLOCKS_H */
diff --git a/arch/arm/mach-lh7a40x/include/mach/constants.h b/arch/arm/mach-lh7a40x/include/mach/constants.h
deleted file mode 100644 (file)
index 55c6edb..0000000
+++ /dev/null
@@ -1,91 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/constants.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#ifndef __ASM_ARCH_CONSTANTS_H
-#define __ASM_ARCH_CONSTANTS_H
-
-
-/* Addressing constants */
-
-       /* SoC CPU IO addressing */
-#define IO_PHYS                        (0x80000000)
-#define IO_VIRT                        (0xf8000000)
-#define IO_SIZE                        (0x0000B000)
-
-#ifdef CONFIG_MACH_KEV7A400
-# define CPLD_PHYS             (0x20000000)
-# define CPLD_VIRT             (0xf2000000)
-# define CPLD_SIZE             PAGE_SIZE
-#endif
-
-#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-
-# define IOBARRIER_PHYS                0x10000000 /* Second bank, fastest timing */
-# define IOBARRIER_VIRT                0xf0000000
-# define IOBARRIER_SIZE                PAGE_SIZE
-
-# define CF_PHYS               0x60200000
-# define CF_VIRT               0xf6020000
-# define CF_SIZE               (8*1024)
-
-       /* The IO mappings for the LPD CPLD are, unfortunately, sparse.  */
-# define CPLDX_PHYS(x)         (0x70000000 | ((x) << 20))
-# define CPLDX_VIRT(x)         (0xf7000000 | ((x) << 16))
-# define CPLD00_PHYS           CPLDX_PHYS (0x00) /* Wired LAN */
-# define CPLD00_VIRT           CPLDX_VIRT (0x00)
-# define CPLD00_SIZE           PAGE_SIZE
-# define CPLD02_PHYS           CPLDX_PHYS (0x02)
-# define CPLD02_VIRT           CPLDX_VIRT (0x02)
-# define CPLD02_SIZE           PAGE_SIZE
-# define CPLD06_PHYS           CPLDX_PHYS (0x06)
-# define CPLD06_VIRT           CPLDX_VIRT (0x06)
-# define CPLD06_SIZE           PAGE_SIZE
-# define CPLD08_PHYS           CPLDX_PHYS (0x08)
-# define CPLD08_VIRT           CPLDX_VIRT (0x08)
-# define CPLD08_SIZE           PAGE_SIZE
-# define CPLD0A_PHYS           CPLDX_PHYS (0x0a)
-# define CPLD0A_VIRT           CPLDX_VIRT (0x0a)
-# define CPLD0A_SIZE           PAGE_SIZE
-# define CPLD0C_PHYS           CPLDX_PHYS (0x0c)
-# define CPLD0C_VIRT           CPLDX_VIRT (0x0c)
-# define CPLD0C_SIZE           PAGE_SIZE
-# define CPLD0E_PHYS           CPLDX_PHYS (0x0e)
-# define CPLD0E_VIRT           CPLDX_VIRT (0x0e)
-# define CPLD0E_SIZE           PAGE_SIZE
-# define CPLD10_PHYS           CPLDX_PHYS (0x10)
-# define CPLD10_VIRT           CPLDX_VIRT (0x10)
-# define CPLD10_SIZE           PAGE_SIZE
-# define CPLD12_PHYS           CPLDX_PHYS (0x12)
-# define CPLD12_VIRT           CPLDX_VIRT (0x12)
-# define CPLD12_SIZE           PAGE_SIZE
-# define CPLD14_PHYS           CPLDX_PHYS (0x14)
-# define CPLD14_VIRT           CPLDX_VIRT (0x14)
-# define CPLD14_SIZE           PAGE_SIZE
-# define CPLD16_PHYS           CPLDX_PHYS (0x16)
-# define CPLD16_VIRT           CPLDX_VIRT (0x16)
-# define CPLD16_SIZE           PAGE_SIZE
-# define CPLD18_PHYS           CPLDX_PHYS (0x18)
-# define CPLD18_VIRT           CPLDX_VIRT (0x18)
-# define CPLD18_SIZE           PAGE_SIZE
-# define CPLD1A_PHYS           CPLDX_PHYS (0x1a)
-# define CPLD1A_VIRT           CPLDX_VIRT (0x1a)
-# define CPLD1A_SIZE           PAGE_SIZE
-#endif
-
-       /* Timing constants */
-
-#define        XTAL_IN                 14745600        /* 14.7456 MHz crystal */
-#define PLL_CLOCK              (XTAL_IN * 21)  /* 309 MHz PLL clock */
-#define MAX_HCLK_KHZ           100000          /* HCLK max limit ~100MHz */
-#define HCLK                   (99993600)
-//#define HCLK                 (119808000)
-
-#endif /* __ASM_ARCH_CONSTANTS_H */
diff --git a/arch/arm/mach-lh7a40x/include/mach/debug-macro.S b/arch/arm/mach-lh7a40x/include/mach/debug-macro.S
deleted file mode 100644 (file)
index cff3362..0000000
+++ /dev/null
@@ -1,37 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- *  Copyright (C) 1994-1999 Russell King
- *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-       @ It is not known if this will be appropriate for every 40x
-       @ board.
-
-               .macro  addruart, rp, rv
-               mov     \rp, #0x00000700        @ offset from base
-               orr     \rv, \rp, #0xf8000000   @ virtual base
-               orr     \rp, \rp, #0x80000000   @ physical base
-               .endm
-
-               .macro  senduart,rd,rx
-               strb    \rd, [\rx]              @ DATA
-               .endm
-
-               .macro  busyuart,rd,rx          @ spin while busy
-1001:          ldr     \rd, [\rx, #0x10]       @ STATUS
-               tst     \rd, #1 << 3            @ BUSY (TX FIFO not empty)
-               bne     1001b                   @ yes, spin
-               .endm
-
-               .macro  waituart,rd,rx          @ wait for Tx FIFO room
-1001:          ldrb    \rd, [\rx, #0x10]       @ STATUS
-               tst     \rd, #1 << 5            @ TXFF (TX FIFO full)
-               bne     1001b                   @ yes, spin
-               .endm
diff --git a/arch/arm/mach-lh7a40x/include/mach/dma.h b/arch/arm/mach-lh7a40x/include/mach/dma.h
deleted file mode 100644 (file)
index baa3f8d..0000000
+++ /dev/null
@@ -1,86 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/dma.h
- *
- *  Copyright (C) 2005 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-typedef enum {
-       DMA_M2M0        = 0,
-       DMA_M2M1        = 1,
-       DMA_M2P0        = 2,    /* Tx */
-       DMA_M2P1        = 3,    /* Rx */
-       DMA_M2P2        = 4,    /* Tx */
-       DMA_M2P3        = 5,    /* Rx */
-       DMA_M2P4        = 6,    /* Tx - AC97 */
-       DMA_M2P5        = 7,    /* Rx - AC97 */
-       DMA_M2P6        = 8,    /* Tx */
-       DMA_M2P7        = 9,    /* Rx */
-} dma_device_t;
-
-#define DMA_LENGTH_MAX         ((64*1024) - 4) /* bytes */
-
-#define DMAC_GCA               __REG(DMAC_PHYS + 0x2b80)
-#define DMAC_GIR               __REG(DMAC_PHYS + 0x2bc0)
-
-#define DMAC_GIR_MMI1          (1<<11)
-#define DMAC_GIR_MMI0          (1<<10)
-#define DMAC_GIR_MPI8          (1<<9)
-#define DMAC_GIR_MPI9          (1<<8)
-#define DMAC_GIR_MPI6          (1<<7)
-#define DMAC_GIR_MPI7          (1<<6)
-#define DMAC_GIR_MPI4          (1<<5)
-#define DMAC_GIR_MPI5          (1<<4)
-#define DMAC_GIR_MPI2          (1<<3)
-#define DMAC_GIR_MPI3          (1<<2)
-#define DMAC_GIR_MPI0          (1<<1)
-#define DMAC_GIR_MPI1          (1<<0)
-
-#define DMAC_M2P0              0x0000
-#define DMAC_M2P1              0x0040
-#define DMAC_M2P2              0x0080
-#define DMAC_M2P3              0x00c0
-#define DMAC_M2P4              0x0240
-#define DMAC_M2P5              0x0200
-#define DMAC_M2P6              0x02c0
-#define DMAC_M2P7              0x0280
-#define DMAC_M2P8              0x0340
-#define DMAC_M2P9              0x0300
-#define DMAC_M2M0              0x0100
-#define DMAC_M2M1              0x0140
-
-#define DMAC_P_PCONTROL(c)     __REG(DMAC_PHYS + (c) + 0x00)
-#define DMAC_P_PINTERRUPT(c)   __REG(DMAC_PHYS + (c) + 0x04)
-#define DMAC_P_PPALLOC(c)      __REG(DMAC_PHYS + (c) + 0x08)
-#define DMAC_P_PSTATUS(c)      __REG(DMAC_PHYS + (c) + 0x0c)
-#define DMAC_P_REMAIN(c)       __REG(DMAC_PHYS + (c) + 0x14)
-#define DMAC_P_MAXCNT0(c)      __REG(DMAC_PHYS + (c) + 0x20)
-#define DMAC_P_BASE0(c)                __REG(DMAC_PHYS + (c) + 0x24)
-#define DMAC_P_CURRENT0(c)     __REG(DMAC_PHYS + (c) + 0x28)
-#define DMAC_P_MAXCNT1(c)      __REG(DMAC_PHYS + (c) + 0x30)
-#define DMAC_P_BASE1(c)                __REG(DMAC_PHYS + (c) + 0x34)
-#define DMAC_P_CURRENT1(c)     __REG(DMAC_PHYS + (c) + 0x38)
-
-#define DMAC_PCONTROL_ENABLE   (1<<4)
-
-#define DMAC_PORT_USB          0
-#define DMAC_PORT_SDMMC                1
-#define DMAC_PORT_AC97_1       2
-#define DMAC_PORT_AC97_2       3
-#define DMAC_PORT_AC97_3       4
-#define DMAC_PORT_UART1                6
-#define DMAC_PORT_UART2                7
-#define DMAC_PORT_UART3                8
-
-#define DMAC_PSTATUS_CURRSTATE_SHIFT   4
-#define DMAC_PSTATUS_CURRSTATE_MASK    0x3
-
-#define DMAC_PSTATUS_NEXTBUF    (1<<6)
-#define DMAC_PSTATUS_STALLRINT  (1<<0)
-
-#define DMAC_INT_CHE            (1<<3)
-#define DMAC_INT_NFB            (1<<1)
-#define DMAC_INT_STALL          (1<<0)
diff --git a/arch/arm/mach-lh7a40x/include/mach/entry-macro.S b/arch/arm/mach-lh7a40x/include/mach/entry-macro.S
deleted file mode 100644 (file)
index 069bb4c..0000000
+++ /dev/null
@@ -1,149 +0,0 @@
-/*
- * arch/arm/mach-lh7a40x/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for LH7A40x platforms
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-
-/* In order to allow there to be support for both of the processor
-   classes at the same time, we make a hack here that isn't very
-   pretty.  At startup, the link pointed to with the
-   branch_irq_lh7a400 symbol is replaced with a NOP when the CPU is
-   detected as a lh7a404.
-
-   *** FIXME: we should clean this up so that there is only one
-             implementation for each CPU's design.
-
-*/
-
-#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
-
-               .macro  disable_fiq
-               .endm
-
-               .macro  get_irqnr_preamble, base, tmp
-               .endm
-
-               .macro  arch_ret_to_user, tmp1, tmp2
-               .endm
-
-               .macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-branch_irq_lh7a400: b 1000f
-
-@ Implementation of the LH7A404 get_irqnr_and_base.
-
-               mov     \irqnr, #0                      @ VIC1 irq base
-               mov     \base, #io_p2v(0x80000000)      @ APB registers
-               add     \base, \base, #0x8000
-               ldr     \tmp, [\base, #0x0030]          @ VIC1_VECTADDR
-               tst     \tmp, #VA_VECTORED              @ Direct vectored
-               bne     1002f
-               tst     \tmp, #VA_VIC1DEFAULT           @ Default vectored VIC1
-               ldrne   \irqstat, [\base, #0]           @ VIC1_IRQSTATUS
-               bne     1001f
-               add     \base, \base, #(0xa000 - 0x8000)
-               ldr     \tmp, [\base, #0x0030]          @ VIC2_VECTADDR
-               tst     \tmp, #VA_VECTORED              @ Direct vectored
-               bne     1002f
-               ldr     \irqstat, [\base, #0]           @ VIC2_IRQSTATUS
-               mov     \irqnr, #32                     @ VIC2 irq base
-
-1001:          movs    \irqstat, \irqstat, lsr #1      @ Shift into carry
-               bcs     1008f                           @ Bit set; irq found
-               add     \irqnr, \irqnr, #1
-               bne     1001b                           @ Until no bits
-               b       1009f                           @ Nothing?  Hmm.
-1002:          and     \irqnr, \tmp, #0x3f             @ Mask for valid bits
-1008:          movs    \irqstat, #1                    @ Force !Z
-               str     \tmp, [\base, #0x0030]          @ Clear vector
-               b       1009f
-
-@ Implementation of the LH7A400 get_irqnr_and_base.
-
-1000:          mov     \irqnr, #0
-               mov     \base, #io_p2v(0x80000000)      @ APB registers
-               ldr     \irqstat, [\base, #0x500]       @ PIC INTSR
-
-1001:          movs    \irqstat, \irqstat, lsr #1      @ Shift into carry
-               bcs     1008f                           @ Bit set; irq found
-               add     \irqnr, \irqnr, #1
-               bne     1001b                           @ Until no bits
-               b       1009f                           @ Nothing?  Hmm.
-1008:          movs    \irqstat, #1                    @ Force !Z
-
-1009:
-               .endm
-
-
-
-#elif defined (CONFIG_ARCH_LH7A400)
-               .macro  disable_fiq
-               .endm
-
-               .macro  get_irqnr_preamble, base, tmp
-               .endm
-
-               .macro  arch_ret_to_user, tmp1, tmp2
-               .endm
-
-               .macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-               mov     \irqnr, #0
-               mov     \base, #io_p2v(0x80000000)      @ APB registers
-               ldr     \irqstat, [\base, #0x500]       @ PIC INTSR
-
-1001:          movs    \irqstat, \irqstat, lsr #1      @ Shift into carry
-               bcs     1008f                           @ Bit set; irq found
-               add     \irqnr, \irqnr, #1
-               bne     1001b                           @ Until no bits
-               b       1009f                           @ Nothing?  Hmm.
-1008:          movs    \irqstat, #1                    @ Force !Z
-1009:
-               .endm
-
-#elif defined(CONFIG_ARCH_LH7A404)
-
-               .macro  disable_fiq
-               .endm
-
-               .macro  get_irqnr_preamble, base, tmp
-               .endm
-
-               .macro  arch_ret_to_user, tmp1, tmp2
-               .endm
-
-               .macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-               mov     \irqnr, #0                      @ VIC1 irq base
-               mov     \base, #io_p2v(0x80000000)      @ APB registers
-               add     \base, \base, #0x8000
-               ldr     \tmp, [\base, #0x0030]          @ VIC1_VECTADDR
-               tst     \tmp, #VA_VECTORED              @ Direct vectored
-               bne     1002f
-               tst     \tmp, #VA_VIC1DEFAULT           @ Default vectored VIC1
-               ldrne   \irqstat, [\base, #0]           @ VIC1_IRQSTATUS
-               bne     1001f
-               add     \base, \base, #(0xa000 - 0x8000)
-               ldr     \tmp, [\base, #0x0030]          @ VIC2_VECTADDR
-               tst     \tmp, #VA_VECTORED              @ Direct vectored
-               bne     1002f
-               ldr     \irqstat, [\base, #0]           @ VIC2_IRQSTATUS
-               mov     \irqnr, #32                     @ VIC2 irq base
-
-1001:          movs    \irqstat, \irqstat, lsr #1      @ Shift into carry
-               bcs     1008f                           @ Bit set; irq found
-               add     \irqnr, \irqnr, #1
-               bne     1001b                           @ Until no bits
-               b       1009f                           @ Nothing?  Hmm.
-1002:          and     \irqnr, \tmp, #0x3f             @ Mask for valid bits
-1008:          movs    \irqstat, #1                    @ Force !Z
-               str     \tmp, [\base, #0x0030]          @ Clear vector
-1009:
-               .endm
-#endif
-
-
diff --git a/arch/arm/mach-lh7a40x/include/mach/hardware.h b/arch/arm/mach-lh7a40x/include/mach/hardware.h
deleted file mode 100644 (file)
index 59d2ace..0000000
+++ /dev/null
@@ -1,62 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/hardware.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  [ Substantially cribbed from arch/arm/mach-pxa/include/mach/hardware.h ]
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <asm/sizes.h>         /* Added for the sake of amba-clcd driver */
-
-#define io_p2v(x) (0xf0000000 | (((x) & 0xfff00000) >> 4) | ((x) & 0x0000ffff))
-#define io_v2p(x) (             (((x) & 0x0fff0000) << 4) | ((x) & 0x0000ffff))
-
-#ifdef __ASSEMBLY__
-
-# define __REG(x)      io_p2v(x)
-# define __PREG(x)     io_v2p(x)
-
-#else
-
-# if 0
-#  define __REG(x)     (*((volatile u32 *)io_p2v(x)))
-# else
-/*
- * This __REG() version gives the same results as the one above,  except
- * that we are fooling gcc somehow so it generates far better and smaller
- * assembly code for access to contiguous registers.  It's a shame that gcc
- * doesn't guess this by itself.
- */
-#include <asm/types.h>
-typedef struct { volatile u32 offset[4096]; } __regbase;
-# define __REGP(x)     ((__regbase *)((x)&~4095))->offset[((x)&4095)>>2]
-# define __REG(x)      __REGP(io_p2v(x))
-typedef struct { volatile u16 offset[4096]; } __regbase16;
-# define __REGP16(x)   ((__regbase16 *)((x)&~4095))->offset[((x)&4095)>>1]
-# define __REG16(x)    __REGP16(io_p2v(x))
-typedef struct { volatile u8 offset[4096]; } __regbase8;
-# define __REGP8(x)    ((__regbase8 *)((x)&~4095))->offset[(x)&4095]
-# define __REG8(x)     __REGP8(io_p2v(x))
-#endif
-
-/* Let's kick gcc's ass again... */
-# define __REG2(x,y)   \
-       ( __builtin_constant_p(y) ? (__REG((x) + (y))) \
-                                 : (*(volatile u32 *)((u32)&__REG(x) + (y))) )
-
-# define __PREG(x)     (io_v2p((u32)&(x)))
-
-#endif
-
-#define MASK_AND_SET(v,m,s)    (v) = ((v)&~(m))|(s)
-
-#include "registers.h"
-
-#endif  /* _ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-lh7a40x/include/mach/io.h b/arch/arm/mach-lh7a40x/include/mach/io.h
deleted file mode 100644 (file)
index 6ece459..0000000
+++ /dev/null
@@ -1,20 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/io.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#ifndef __ASM_ARCH_IO_H
-#define __ASM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/* No ISA or PCI bus on this machine. */
-#define __io(a)                __typesafe_io(a)
-#define __mem_pci(a)   (a)
-
-#endif /* __ASM_ARCH_IO_H */
diff --git a/arch/arm/mach-lh7a40x/include/mach/irqs.h b/arch/arm/mach-lh7a40x/include/mach/irqs.h
deleted file mode 100644 (file)
index 0f9b836..0000000
+++ /dev/null
@@ -1,200 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/irqs.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-/* It is to be seen whether or not we can build a kernel for more than
- * one board.  For the time being, these macros assume that we cannot.
- * Thus, it is OK to ifdef machine/board specific IRQ assignments.
- */
-
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-
-#define FIQ_START      80
-
-#if defined (CONFIG_ARCH_LH7A400)
-
-  /* FIQs */
-
-# define IRQ_GPIO0FIQ  0       /* GPIO External FIQ Interrupt on F0 */
-# define IRQ_BLINT     1       /* Battery Low */
-# define IRQ_WEINT     2       /* Watchdog Timer, WDT overflow */
-# define IRQ_MCINT     3       /* Media Change, MEDCHG pin rising */
-
-  /* IRQs */
-
-# define IRQ_CSINT     4       /* Audio Codec (ACI) */
-# define IRQ_GPIO1INTR 5       /* GPIO External IRQ Interrupt on F1 */
-# define IRQ_GPIO2INTR 6       /* GPIO External IRQ Interrupt on F2 */
-# define IRQ_GPIO3INTR 7       /* GPIO External IRQ Interrupt on F3 */
-# define IRQ_T1UI      8       /* Timer 1 underflow */
-# define IRQ_T2UI      9       /* Timer 2 underflow */
-# define IRQ_RTCMI     10
-# define IRQ_TINTR     11      /* Clock State Controller 64 Hz tick (CSC) */
-# define IRQ_UART1INTR 12
-# define IRQ_UART2INTR 13
-# define IRQ_LCDINTR   14
-# define IRQ_SSIEOT    15      /* Synchronous Serial Interface (SSI) */
-# define IRQ_UART3INTR 16
-# define IRQ_SCIINTR   17      /* Smart Card Interface (SCI) */
-# define IRQ_AACINTR   18      /* Advanced Audio Codec (AAC) */
-# define IRQ_MMCINTR   19      /* Multimedia Card (MMC) */
-# define IRQ_USBINTR   20
-# define IRQ_DMAINTR   21
-# define IRQ_T3UI      22      /* Timer 3 underflow */
-# define IRQ_GPIO4INTR 23      /* GPIO External IRQ Interrupt on F4 */
-# define IRQ_GPIO5INTR 24      /* GPIO External IRQ Interrupt on F5 */
-# define IRQ_GPIO6INTR 25      /* GPIO External IRQ Interrupt on F6 */
-# define IRQ_GPIO7INTR 26      /* GPIO External IRQ Interrupt on F7 */
-# define IRQ_BMIINTR   27      /* Battery Monitor Interface (BMI) */
-
-# define NR_IRQ_CPU    28      /* IRQs directly recognized by CPU */
-
-       /* Given IRQ, return GPIO interrupt number 0-7 */
-# define IRQ_TO_GPIO(i)  ((i) \
-       - (((i) > IRQ_GPIO3INTR) ? IRQ_GPIO4INTR - IRQ_GPIO3INTR - 1 : 0)\
-       - (((i) > IRQ_GPIO0INTR) ? IRQ_GPIO1INTR - IRQ_GPIO0INTR - 1 : 0))
-
-#endif
-
-#if defined (CONFIG_ARCH_LH7A404)
-
-# define IRQ_BROWN     0       /* Brownout */
-# define IRQ_WDTINTR   1       /* Watchdog Timer */
-# define IRQ_COMMRX    2       /* ARM Comm Rx for Debug */
-# define IRQ_COMMTX    3       /* ARM Comm Tx for Debug */
-# define IRQ_T1UI      4       /* Timer 1 underflow */
-# define IRQ_T2UI      5       /* Timer 2 underflow */
-# define IRQ_CSINT     6       /* Codec Interrupt (shared by AAC on 404) */
-# define IRQ_DMAM2P0   7       /* -- DMA Memory to Peripheral */
-# define IRQ_DMAM2P1   8
-# define IRQ_DMAM2P2   9
-# define IRQ_DMAM2P3   10
-# define IRQ_DMAM2P4   11
-# define IRQ_DMAM2P5   12
-# define IRQ_DMAM2P6   13
-# define IRQ_DMAM2P7   14
-# define IRQ_DMAM2P8   15
-# define IRQ_DMAM2P9   16
-# define IRQ_DMAM2M0   17      /* -- DMA Memory to Memory */
-# define IRQ_DMAM2M1   18
-# define IRQ_GPIO0INTR 19      /* -- GPIOF Interrupt */
-# define IRQ_GPIO1INTR 20
-# define IRQ_GPIO2INTR 21
-# define IRQ_GPIO3INTR 22
-# define IRQ_SOFT_V1_23        23      /* -- Unassigned */
-# define IRQ_SOFT_V1_24        24
-# define IRQ_SOFT_V1_25        25
-# define IRQ_SOFT_V1_26        26
-# define IRQ_SOFT_V1_27        27
-# define IRQ_SOFT_V1_28        28
-# define IRQ_SOFT_V1_29        29
-# define IRQ_SOFT_V1_30        30
-# define IRQ_SOFT_V1_31        31
-
-# define IRQ_BLINT     32      /* Battery Low */
-# define IRQ_BMIINTR   33      /* Battery Monitor */
-# define IRQ_MCINTR    34      /* Media Change */
-# define IRQ_TINTR     35      /* 64Hz Tick */
-# define IRQ_WEINT     36      /* Watchdog Expired */
-# define IRQ_RTCMI     37      /* Real-time Clock Match */
-# define IRQ_UART1INTR 38      /* UART1 Interrupt (including error) */
-# define IRQ_UART1ERR  39      /* UART1 Error */
-# define IRQ_UART2INTR 40      /* UART2 Interrupt (including error) */
-# define IRQ_UART2ERR  41      /* UART2 Error */
-# define IRQ_UART3INTR 42      /* UART3 Interrupt (including error) */
-# define IRQ_UART3ERR  43      /* UART3 Error */
-# define IRQ_SCIINTR   44      /* Smart Card */
-# define IRQ_TSCINTR   45      /* Touchscreen */
-# define IRQ_KMIINTR   46      /* Keyboard/Mouse (PS/2) */
-# define IRQ_GPIO4INTR 47      /* -- GPIOF Interrupt */
-# define IRQ_GPIO5INTR 48
-# define IRQ_GPIO6INTR 49
-# define IRQ_GPIO7INTR 50
-# define IRQ_T3UI      51      /* Timer 3 underflow */
-# define IRQ_LCDINTR   52      /* LCD Controller */
-# define IRQ_SSPINTR   53      /* Synchronous Serial Port */
-# define IRQ_SDINTR    54      /* Secure Digital Port (MMC) */
-# define IRQ_USBINTR   55      /* USB Device Port */
-# define IRQ_USHINTR   56      /* USB Host Port */
-# define IRQ_SOFT_V2_25        57      /* -- Unassigned */
-# define IRQ_SOFT_V2_26        58
-# define IRQ_SOFT_V2_27        59
-# define IRQ_SOFT_V2_28        60
-# define IRQ_SOFT_V2_29        61
-# define IRQ_SOFT_V2_30        62
-# define IRQ_SOFT_V2_31        63
-
-# define NR_IRQ_CPU    64      /* IRQs directly recognized by CPU */
-
-       /* Given IRQ, return GPIO interrupt number 0-7 */
-# define IRQ_TO_GPIO(i)  ((i) \
-       - (((i) > IRQ_GPIO3INTR) ? IRQ_GPIO4INTR - IRQ_GPIO3INTR - 1 : 0)\
-       - IRQ_GPIO0INTR)
-
-                       /* Vector Address constants */
-# define VA_VECTORED   0x100   /* Set for vectored interrupt */
-# define VA_VIC1DEFAULT        0x200   /* Set as default VECTADDR for VIC1 */
-# define VA_VIC2DEFAULT        0x400   /* Set as default VECTADDR for VIC2 */
-
-#endif
-
-  /* IRQ aliases */
-
-#if !defined (IRQ_GPIO0INTR)
-# define IRQ_GPIO0INTR IRQ_GPIO0FIQ
-#endif
-#define IRQ_TICK       IRQ_TINTR
-#define IRQ_PCC1_RDY   IRQ_GPIO6INTR   /* PCCard 1 ready */
-#define IRQ_PCC2_RDY   IRQ_GPIO7INTR   /* PCCard 2 ready */
-#define IRQ_USB                IRQ_USBINTR     /* USB device */
-
-#ifdef CONFIG_MACH_KEV7A400
-# define IRQ_TS                IRQ_GPIOFIQ     /* Touchscreen */
-# define IRQ_CPLD      IRQ_GPIO1INTR   /* CPLD cascade */
-# define IRQ_PCC1_CD   IRQ_GPIO_F2     /* PCCard 1 card detect */
-# define IRQ_PCC2_CD   IRQ_GPIO_F3     /* PCCard 2 card detect */
-#endif
-
-#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-# define IRQ_CPLD_V28  IRQ_GPIO7INTR   /* CPLD cascade through GPIO_PF7 */
-# define IRQ_CPLD_V34  IRQ_GPIO3INTR   /* CPLD cascade through GPIO_PF3 */
-#endif
-
-  /* System specific IRQs */
-
-#define IRQ_BOARD_START NR_IRQ_CPU
-
-#ifdef CONFIG_MACH_KEV7A400
-# define IRQ_KEV7A400_CPLD     IRQ_BOARD_START
-# define NR_IRQ_BOARD          5
-# define IRQ_KEV7A400_MMC_CD   IRQ_KEV7A400_CPLD + 0   /* MMC Card Detect */
-# define IRQ_KEV7A400_RI2      IRQ_KEV7A400_CPLD + 1   /* Ring Indicator 2 */
-# define IRQ_KEV7A400_IDE_CF   IRQ_KEV7A400_CPLD + 2   /* Compact Flash (?) */
-# define IRQ_KEV7A400_ETH_INT  IRQ_KEV7A400_CPLD + 3   /* Ethernet chip */
-# define IRQ_KEV7A400_INT      IRQ_KEV7A400_CPLD + 4
-#endif
-
-#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-# define IRQ_LPD7A40X_CPLD     IRQ_BOARD_START
-# define NR_IRQ_BOARD          2
-# define IRQ_LPD7A40X_ETH_INT  IRQ_LPD7A40X_CPLD + 0   /* Ethernet chip */
-# define IRQ_LPD7A400_TS       IRQ_LPD7A40X_CPLD + 1   /* Touch screen */
-#endif
-
-#if defined (CONFIG_MACH_LPD7A400)
-# define IRQ_TOUCH             IRQ_LPD7A400_TS
-#endif
-
-#define NR_IRQS                (NR_IRQ_CPU + NR_IRQ_BOARD)
-
-#endif
diff --git a/arch/arm/mach-lh7a40x/include/mach/memory.h b/arch/arm/mach-lh7a40x/include/mach/memory.h
deleted file mode 100644 (file)
index edb8f5f..0000000
+++ /dev/null
@@ -1,28 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/memory.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- *
- *  Refer to <file:Documentation/arm/Sharp-LH/SDRAM> for more information.
- *
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PHYS_OFFSET    UL(0xc0000000)
-
-/*
- * Sparsemem version of the above
- */
-#define MAX_PHYSMEM_BITS       32
-#define SECTION_SIZE_BITS      24
-
-#endif
diff --git a/arch/arm/mach-lh7a40x/include/mach/registers.h b/arch/arm/mach-lh7a40x/include/mach/registers.h
deleted file mode 100644 (file)
index ea44396..0000000
+++ /dev/null
@@ -1,224 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/registers.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <mach/constants.h>
-
-#ifndef __ASM_ARCH_REGISTERS_H
-#define __ASM_ARCH_REGISTERS_H
-
-
-       /* Physical register base addresses */
-
-#define AC97C_PHYS     (0x80000000)    /* AC97 Controller */
-#define MMC_PHYS       (0x80000100)    /* Multimedia Card Controller */
-#define USB_PHYS       (0x80000200)    /* USB Client */
-#define SCI_PHYS       (0x80000300)    /* Secure Card Interface */
-#define CSC_PHYS       (0x80000400)    /* Clock/State Controller  */
-#define INTC_PHYS      (0x80000500)    /* Interrupt Controller */
-#define UART1_PHYS     (0x80000600)    /* UART1 Controller */
-#define SIR_PHYS       (0x80000600)    /* IR Controller, same are UART1 */
-#define UART2_PHYS     (0x80000700)    /* UART2 Controller */
-#define UART3_PHYS     (0x80000800)    /* UART3 Controller */
-#define DCDC_PHYS      (0x80000900)    /* DC to DC Controller */
-#define ACI_PHYS       (0x80000a00)    /* Audio Codec Interface */
-#define SSP_PHYS       (0x80000b00)    /* Synchronous ... */
-#define TIMER_PHYS     (0x80000c00)    /* Timer Controller */
-#define RTC_PHYS       (0x80000d00)    /* Real-time Clock */
-#define GPIO_PHYS      (0x80000e00)    /* General Purpose IO */
-#define BMI_PHYS       (0x80000f00)    /* Battery Monitor Interface */
-#define HRTFTC_PHYS    (0x80001000)    /* High-res TFT Controller (LH7A400) */
-#define ALI_PHYS       (0x80001000)    /* Advanced LCD Interface (LH7A404) */
-#define WDT_PHYS       (0x80001400)    /* Watchdog Timer */
-#define SMC_PHYS       (0x80002000)    /* Static Memory Controller */
-#define SDRC_PHYS      (0x80002400)    /* SDRAM Controller */
-#define DMAC_PHYS      (0x80002800)    /* DMA Controller */
-#define CLCDC_PHYS     (0x80003000)    /* Color LCD Controller */
-
-       /* Physical registers of the LH7A404 */
-
-#define ADC_PHYS       (0x80001300)    /* A/D & Touchscreen Controller */
-#define VIC1_PHYS      (0x80008000)    /* Vectored Interrupt Controller 1 */
-#define USBH_PHYS      (0x80009000)    /* USB OHCI host controller */
-#define VIC2_PHYS      (0x8000a000)    /* Vectored Interrupt Controller 2 */
-
-/*#define KBD_PHYS     (0x80000e00) */
-/*#define LCDICP_PHYS  (0x80001000) */
-
-
-       /* Clock/State Controller register */
-
-#define CSC_PWRSR      __REG(CSC_PHYS + 0x00) /* Reset register & ID */
-#define CSC_PWRCNT     __REG(CSC_PHYS + 0x04) /* Power control */
-#define CSC_CLKSET     __REG(CSC_PHYS + 0x20) /* Clock speed control */
-#define CSC_USBDRESET  __REG(CSC_PHYS + 0x4c) /* USB Device resets */
-
-#define CSC_PWRCNT_USBH_EN     (1<<28) /* USB Host power enable */
-#define CSC_PWRCNT_DMAC_M2M1_EN        (1<<27)
-#define CSC_PWRCNT_DMAC_M2M0_EN        (1<<26)
-#define CSC_PWRCNT_DMAC_M2P8_EN        (1<<25)
-#define CSC_PWRCNT_DMAC_M2P9_EN        (1<<24)
-#define CSC_PWRCNT_DMAC_M2P6_EN        (1<<23)
-#define CSC_PWRCNT_DMAC_M2P7_EN        (1<<22)
-#define CSC_PWRCNT_DMAC_M2P4_EN        (1<<21)
-#define CSC_PWRCNT_DMAC_M2P5_EN        (1<<20)
-#define CSC_PWRCNT_DMAC_M2P2_EN        (1<<19)
-#define CSC_PWRCNT_DMAC_M2P3_EN        (1<<18)
-#define CSC_PWRCNT_DMAC_M2P0_EN        (1<<17)
-#define CSC_PWRCNT_DMAC_M2P1_EN        (1<<16)
-
-#define CSC_PWRSR_CHIPMAN_SHIFT        (24)
-#define CSC_PWRSR_CHIPMAN_MASK (0xff)
-#define CSC_PWRSR_CHIPID_SHIFT (16)
-#define CSC_PWRSR_CHIPID_MASK  (0xff)
-
-#define CSC_USBDRESET_APBRESETREG      (1<<1)
-#define CSC_USBDRESET_IORESETREG       (1<<0)
-
-       /* Interrupt Controller registers */
-
-#define INTC_INTSR     __REG(INTC_PHYS + 0x00) /* Status */
-#define INTC_INTRSR    __REG(INTC_PHYS + 0x04) /* Raw Status */
-#define INTC_INTENS    __REG(INTC_PHYS + 0x08) /* Enable Set */
-#define INTC_INTENC    __REG(INTC_PHYS + 0x0c) /* Enable Clear */
-
-
-       /* Vectored Interrupted Controller registers */
-
-#define VIC1_IRQSTATUS __REG(VIC1_PHYS + 0x00)
-#define VIC1_FIQSTATUS __REG(VIC1_PHYS + 0x04)
-#define VIC1_RAWINTR   __REG(VIC1_PHYS + 0x08)
-#define VIC1_INTSEL    __REG(VIC1_PHYS + 0x0c)
-#define VIC1_INTEN     __REG(VIC1_PHYS + 0x10)
-#define VIC1_INTENCLR  __REG(VIC1_PHYS + 0x14)
-#define VIC1_SOFTINT   __REG(VIC1_PHYS + 0x18)
-#define VIC1_SOFTINTCLR        __REG(VIC1_PHYS + 0x1c)
-#define VIC1_PROTECT   __REG(VIC1_PHYS + 0x20)
-#define VIC1_VECTADDR  __REG(VIC1_PHYS + 0x30)
-#define VIC1_NVADDR    __REG(VIC1_PHYS + 0x34)
-#define VIC1_VAD0      __REG(VIC1_PHYS + 0x100)
-#define VIC1_VECTCNTL0 __REG(VIC1_PHYS + 0x200)
-#define VIC2_IRQSTATUS __REG(VIC2_PHYS + 0x00)
-#define VIC2_FIQSTATUS __REG(VIC2_PHYS + 0x04)
-#define VIC2_RAWINTR   __REG(VIC2_PHYS + 0x08)
-#define VIC2_INTSEL    __REG(VIC2_PHYS + 0x0c)
-#define VIC2_INTEN     __REG(VIC2_PHYS + 0x10)
-#define VIC2_INTENCLR  __REG(VIC2_PHYS + 0x14)
-#define VIC2_SOFTINT   __REG(VIC2_PHYS + 0x18)
-#define VIC2_SOFTINTCLR        __REG(VIC2_PHYS + 0x1c)
-#define VIC2_PROTECT   __REG(VIC2_PHYS + 0x20)
-#define VIC2_VECTADDR  __REG(VIC2_PHYS + 0x30)
-#define VIC2_NVADDR    __REG(VIC2_PHYS + 0x34)
-#define VIC2_VAD0      __REG(VIC2_PHYS + 0x100)
-#define VIC2_VECTCNTL0 __REG(VIC2_PHYS + 0x200)
-
-#define VIC_CNTL_ENABLE        (0x20)
-
-       /* USB Host registers (Open HCI compatible) */
-
-#define USBH_CMDSTATUS __REG(USBH_PHYS + 0x08)
-
-
-       /* GPIO registers */
-
-#define GPIO_INTTYPE1  __REG(GPIO_PHYS + 0x4c) /* Interrupt Type 1 (Edge) */
-#define GPIO_INTTYPE2  __REG(GPIO_PHYS + 0x50) /* Interrupt Type 2 */
-#define GPIO_GPIOFEOI  __REG(GPIO_PHYS + 0x54) /* GPIO End-of-Interrupt */
-#define GPIO_GPIOINTEN __REG(GPIO_PHYS + 0x58) /* GPIO Interrupt Enable */
-#define GPIO_INTSTATUS __REG(GPIO_PHYS + 0x5c) /* GPIO Interrupt Status */
-#define GPIO_PINMUX    __REG(GPIO_PHYS + 0x2c)
-#define GPIO_PADD      __REG(GPIO_PHYS + 0x10)
-#define GPIO_PAD       __REG(GPIO_PHYS + 0x00)
-#define GPIO_PCD       __REG(GPIO_PHYS + 0x08)
-#define GPIO_PCDD      __REG(GPIO_PHYS + 0x18)
-#define GPIO_PEDD      __REG(GPIO_PHYS + 0x24)
-#define GPIO_PED       __REG(GPIO_PHYS + 0x20)
-
-
-       /* Static Memory Controller registers */
-
-#define SMC_BCR0       __REG(SMC_PHYS + 0x00)  /* Bank 0 Configuration */
-#define SMC_BCR1       __REG(SMC_PHYS + 0x04)  /* Bank 1 Configuration */
-#define SMC_BCR2       __REG(SMC_PHYS + 0x08)  /* Bank 2 Configuration */
-#define SMC_BCR3       __REG(SMC_PHYS + 0x0C)  /* Bank 3 Configuration */
-#define SMC_BCR6       __REG(SMC_PHYS + 0x18)  /* Bank 6 Configuration */
-#define SMC_BCR7       __REG(SMC_PHYS + 0x1c)  /* Bank 7 Configuration */
-
-
-#ifdef CONFIG_MACH_KEV7A400
-# define CPLD_RD_OPT_DIP_SW    __REG16(CPLD_PHYS + 0x00) /* Read Option SW */
-# define CPLD_WR_IO_BRD_CTL    __REG16(CPLD_PHYS + 0x00) /* Write Control */
-# define CPLD_RD_PB_KEYS       __REG16(CPLD_PHYS + 0x02) /* Read Btn Keys */
-# define CPLD_LATCHED_INTS     __REG16(CPLD_PHYS + 0x04) /* Read INTR stat. */
-# define CPLD_CL_INT           __REG16(CPLD_PHYS + 0x04) /* Clear INTR stat */
-# define CPLD_BOOT_MMC_STATUS  __REG16(CPLD_PHYS + 0x06) /* R/O */
-# define CPLD_RD_KPD_ROW_SENSE __REG16(CPLD_PHYS + 0x08)
-# define CPLD_WR_PB_INT_MASK   __REG16(CPLD_PHYS + 0x08)
-# define CPLD_RD_BRD_DISP_SW   __REG16(CPLD_PHYS + 0x0a)
-# define CPLD_WR_EXT_INT_MASK  __REG16(CPLD_PHYS + 0x0a)
-# define CPLD_LCD_PWR_CNTL     __REG16(CPLD_PHYS + 0x0c)
-# define CPLD_SEVEN_SEG                __REG16(CPLD_PHYS + 0x0e) /* 7 seg. LED mask */
-
-#endif
-
-#if defined (CONFIG_MACH_LPD7A400) || defined (CONFIG_MACH_LPD7A404)
-
-# define CPLD_CONTROL          __REG16(CPLD02_PHYS)
-# define CPLD_SPI_DATA         __REG16(CPLD06_PHYS)
-# define CPLD_SPI_CONTROL      __REG16(CPLD08_PHYS)
-# define CPLD_SPI_EEPROM       __REG16(CPLD0A_PHYS)
-# define CPLD_INTERRUPTS       __REG16(CPLD0C_PHYS) /* IRQ mask/status */
-# define CPLD_BOOT_MODE                __REG16(CPLD0E_PHYS)
-# define CPLD_FLASH            __REG16(CPLD10_PHYS)
-# define CPLD_POWER_MGMT       __REG16(CPLD12_PHYS)
-# define CPLD_REVISION         __REG16(CPLD14_PHYS)
-# define CPLD_GPIO_EXT         __REG16(CPLD16_PHYS)
-# define CPLD_GPIO_DATA                __REG16(CPLD18_PHYS)
-# define CPLD_GPIO_DIR         __REG16(CPLD1A_PHYS)
-
-#endif
-
-       /* Timer registers */
-
-#define TIMER_LOAD1    __REG(TIMER_PHYS + 0x00) /* Timer 1 initial value */
-#define TIMER_VALUE1   __REG(TIMER_PHYS + 0x04) /* Timer 1 current value */
-#define TIMER_CONTROL1 __REG(TIMER_PHYS + 0x08) /* Timer 1 control word */
-#define TIMER_EOI1     __REG(TIMER_PHYS + 0x0c) /* Timer 1 interrupt clear */
-
-#define TIMER_LOAD2    __REG(TIMER_PHYS + 0x20) /* Timer 2 initial value */
-#define TIMER_VALUE2   __REG(TIMER_PHYS + 0x24) /* Timer 2 current value */
-#define TIMER_CONTROL2 __REG(TIMER_PHYS + 0x28) /* Timer 2 control word */
-#define TIMER_EOI2     __REG(TIMER_PHYS + 0x2c) /* Timer 2 interrupt clear */
-
-#define TIMER_BUZZCON  __REG(TIMER_PHYS + 0x40) /* Buzzer configuration */
-
-#define TIMER_LOAD3    __REG(TIMER_PHYS + 0x80) /* Timer 3 initial value */
-#define TIMER_VALUE3   __REG(TIMER_PHYS + 0x84) /* Timer 3 current value */
-#define TIMER_CONTROL3 __REG(TIMER_PHYS + 0x88) /* Timer 3 control word */
-#define TIMER_EOI3     __REG(TIMER_PHYS + 0x8c) /* Timer 3 interrupt clear */
-
-#define TIMER_C_ENABLE         (1<<7)
-#define TIMER_C_PERIODIC       (1<<6)
-#define TIMER_C_FREERUNNING    (0)
-#define TIMER_C_2KHZ           (0x00)          /* 1.986 kHz */
-#define TIMER_C_508KHZ         (0x08)
-
-       /* GPIO registers */
-
-#define GPIO_PFDD              __REG(GPIO_PHYS + 0x34) /* PF direction */
-#define GPIO_INTTYPE1          __REG(GPIO_PHYS + 0x4c) /* IRQ edge or lvl  */
-#define GPIO_INTTYPE2          __REG(GPIO_PHYS + 0x50) /* IRQ activ hi/lo */
-#define GPIO_GPIOFEOI          __REG(GPIO_PHYS + 0x54) /* GPIOF end of IRQ */
-#define GPIO_GPIOFINTEN                __REG(GPIO_PHYS + 0x58) /* GPIOF IRQ enable */
-#define GPIO_INTSTATUS         __REG(GPIO_PHYS + 0x5c) /* GPIOF IRQ latch */
-#define GPIO_RAWINTSTATUS      __REG(GPIO_PHYS + 0x60) /* GPIOF IRQ raw */
-
-
-#endif  /* _ASM_ARCH_REGISTERS_H */
diff --git a/arch/arm/mach-lh7a40x/include/mach/ssp.h b/arch/arm/mach-lh7a40x/include/mach/ssp.h
deleted file mode 100644 (file)
index 5099161..0000000
+++ /dev/null
@@ -1,70 +0,0 @@
-/* ssp.h
-
-   written by Marc Singer
-   6 Dec 2004
-
-   Copyright (C) 2004 Marc Singer
-
-   -----------
-   DESCRIPTION
-   -----------
-
-   This SSP header is available throughout the kernel, for this
-   machine/architecture, because drivers that use it may be dispersed.
-
-   This file was cloned from the 7952x implementation.  It would be
-   better to share them, but we're taking an easier approach for the
-   time being.
-
-*/
-
-#if !defined (__SSP_H__)
-#    define   __SSP_H__
-
-/* ----- Includes */
-
-/* ----- Types */
-
-struct ssp_driver {
-       int  (*init)            (void);
-       void (*exit)            (void);
-       void (*acquire)         (void);
-       void (*release)         (void);
-       int  (*configure)       (int device, int mode, int speed,
-                                int frame_size_write, int frame_size_read);
-       void (*chip_select)     (int enable);
-       void (*set_callbacks)   (void* handle,
-                                irqreturn_t (*callback_tx)(void*),
-                                irqreturn_t (*callback_rx)(void*));
-       void (*enable)          (void);
-       void (*disable)         (void);
-//     int  (*save_state)      (void*);
-//     void (*restore_state)   (void*);
-       int  (*read)            (void);
-       int  (*write)           (u16 data);
-       int  (*write_read)      (u16 data);
-       void (*flush)           (void);
-       void (*write_async)     (void* pv, size_t cb);
-       size_t (*write_pos)     (void);
-};
-
-       /* These modes are only available on the LH79524 */
-#define SSP_MODE_SPI           (1)
-#define SSP_MODE_SSI           (2)
-#define SSP_MODE_MICROWIRE     (3)
-#define SSP_MODE_I2S           (4)
-
-       /* CPLD SPI devices */
-#define DEVICE_EEPROM  0       /* Configuration eeprom */
-#define DEVICE_MAC     1       /* MAC eeprom (LPD79524) */
-#define DEVICE_CODEC   2       /* Audio codec */
-#define DEVICE_TOUCH   3       /* Touch screen (LPD79520) */
-
-/* ----- Globals */
-
-/* ----- Prototypes */
-
-//extern struct ssp_driver lh79520_i2s_driver;
-extern struct ssp_driver lh7a400_cpld_ssp_driver;
-
-#endif  /* __SSP_H__ */
diff --git a/arch/arm/mach-lh7a40x/include/mach/system.h b/arch/arm/mach-lh7a40x/include/mach/system.h
deleted file mode 100644 (file)
index 45a56d3..0000000
+++ /dev/null
@@ -1,19 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/system.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-static inline void arch_idle(void)
-{
-       cpu_do_idle ();
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
-       cpu_reset (0);
-}
diff --git a/arch/arm/mach-lh7a40x/include/mach/timex.h b/arch/arm/mach-lh7a40x/include/mach/timex.h
deleted file mode 100644 (file)
index 08028ce..0000000
+++ /dev/null
@@ -1,17 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/timex.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <mach/constants.h>
-
-#define CLOCK_TICK_RATE                (PLL_CLOCK/6/16)
-
-/*
-#define CLOCK_TICK_RATE                3686400
-*/
diff --git a/arch/arm/mach-lh7a40x/include/mach/uncompress.h b/arch/arm/mach-lh7a40x/include/mach/uncompress.h
deleted file mode 100644 (file)
index 55b80d4..0000000
+++ /dev/null
@@ -1,38 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/uncompress.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <mach/registers.h>
-
-#ifndef UART_R_DATA
-# define UART_R_DATA   (0x00)
-#endif
-#ifndef UART_R_STATUS
-# define UART_R_STATUS (0x10)
-#endif
-#define nTxRdy         (0x20)  /* Not TxReady (literally Tx FIFO full) */
-
-       /* Access UART with physical addresses before MMU is setup */
-#define UART_STATUS (*(volatile unsigned long*) (UART2_PHYS + UART_R_STATUS))
-#define UART_DATA   (*(volatile unsigned long*) (UART2_PHYS + UART_R_DATA))
-
-static inline void putc(int ch)
-{
-       while (UART_STATUS & nTxRdy)
-               barrier();
-       UART_DATA = ch;
-}
-
-static inline void flush(void)
-{
-}
-
-       /* NULL functions; we don't presently need them */
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
diff --git a/arch/arm/mach-lh7a40x/include/mach/vmalloc.h b/arch/arm/mach-lh7a40x/include/mach/vmalloc.h
deleted file mode 100644 (file)
index d62da73..0000000
+++ /dev/null
@@ -1,10 +0,0 @@
-/* arch/arm/mach-lh7a40x/include/mach/vmalloc.h
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-#define VMALLOC_END       (0xe8000000UL)
diff --git a/arch/arm/mach-lh7a40x/irq-kev7a400.c b/arch/arm/mach-lh7a40x/irq-kev7a400.c
deleted file mode 100644 (file)
index c7433b3..0000000
+++ /dev/null
@@ -1,93 +0,0 @@
-/* arch/arm/mach-lh7a40x/irq-kev7a400.c
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/interrupt.h>
-#include <linux/init.h>
-
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/hardware.h>
-#include <asm/mach/irqs.h>
-
-#include "common.h"
-
-  /* KEV7a400 CPLD IRQ handling */
-
-static u16 CPLD_IRQ_mask;      /* Mask for CPLD IRQs, 1 == unmasked */
-
-static void
-lh7a400_ack_cpld_irq (u32 irq)
-{
-       CPLD_CL_INT = 1 << (irq - IRQ_KEV7A400_CPLD);
-}
-
-static void
-lh7a400_mask_cpld_irq (u32 irq)
-{
-       CPLD_IRQ_mask &= ~(1 << (irq - IRQ_KEV7A400_CPLD));
-       CPLD_WR_PB_INT_MASK = CPLD_IRQ_mask;
-}
-
-static void
-lh7a400_unmask_cpld_irq (u32 irq)
-{
-       CPLD_IRQ_mask |= 1 << (irq - IRQ_KEV7A400_CPLD);
-       CPLD_WR_PB_INT_MASK = CPLD_IRQ_mask;
-}
-
-static struct
-irq_chip lh7a400_cpld_chip = {
-       .name   = "CPLD",
-       .ack    = lh7a400_ack_cpld_irq,
-       .mask   = lh7a400_mask_cpld_irq,
-       .unmask = lh7a400_unmask_cpld_irq,
-};
-
-static void
-lh7a400_cpld_handler (unsigned int irq, struct irq_desc *desc)
-{
-       u32 mask = CPLD_LATCHED_INTS;
-       irq = IRQ_KEV_7A400_CPLD;
-       for (; mask; mask >>= 1, ++irq) {
-               if (mask & 1)
-                       desc[irq].handle (irq, desc);
-       }
-}
-
-  /* IRQ initialization */
-
-void __init
-lh7a400_init_board_irq (void)
-{
-       int irq;
-
-       for (irq = IRQ_KEV7A400_CPLD;
-            irq < IRQ_KEV7A400_CPLD + NR_IRQ_KEV7A400_CPLD; ++irq) {
-               set_irq_chip (irq, &lh7a400_cpld_chip);
-               set_irq_handler (irq, handle_edge_irq);
-               set_irq_flags (irq, IRQF_VALID);
-       }
-       set_irq_chained_handler (IRQ_CPLD, kev7a400_cpld_handler);
-
-               /* Clear all CPLD interrupts */
-       CPLD_CL_INT = 0xff; /* CPLD_INTR_MMC_CD | CPLD_INTR_ETH_INT; */
-
-    /* *** FIXME CF enabled in ide-probe.c */
-
-       GPIO_GPIOINTEN = 0;             /* Disable all GPIO interrupts */
-       barrier();
-       GPIO_INTTYPE1
-               = (GPIO_INTR_PCC1_CD | GPIO_INTR_PCC1_CD); /* Edge trig. */
-       GPIO_INTTYPE2 = 0;              /* Falling edge & low-level */
-       GPIO_GPIOFEOI = 0xff;           /* Clear all GPIO interrupts */
-       GPIO_GPIOINTEN = 0xff;          /* Enable all GPIO interrupts */
-
-       init_FIQ();
-}
diff --git a/arch/arm/mach-lh7a40x/irq-lh7a400.c b/arch/arm/mach-lh7a40x/irq-lh7a400.c
deleted file mode 100644 (file)
index f2e7e65..0000000
+++ /dev/null
@@ -1,91 +0,0 @@
-/* arch/arm/mach-lh7a40x/irq-lh7a400.c
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <mach/irqs.h>
-
-#include "common.h"
-
-  /* CPU IRQ handling */
-
-static void lh7a400_mask_irq(struct irq_data *d)
-{
-       INTC_INTENC = (1 << d->irq);
-}
-
-static void lh7a400_unmask_irq(struct irq_data *d)
-{
-       INTC_INTENS = (1 << d->irq);
-}
-
-static void lh7a400_ack_gpio_irq(struct irq_data *d)
-{
-       GPIO_GPIOFEOI = (1 << IRQ_TO_GPIO (d->irq));
-       INTC_INTENC = (1 << d->irq);
-}
-
-static struct irq_chip lh7a400_internal_chip = {
-       .name           = "MPU",
-       .irq_ack        = lh7a400_mask_irq, /* Level triggering -> mask is ack */
-       .irq_mask       = lh7a400_mask_irq,
-       .irq_unmask     = lh7a400_unmask_irq,
-};
-
-static struct irq_chip lh7a400_gpio_chip = {
-       .name           = "GPIO",
-       .irq_ack        = lh7a400_ack_gpio_irq,
-       .irq_mask       = lh7a400_mask_irq,
-       .irq_unmask     = lh7a400_unmask_irq,
-};
-
-
-  /* IRQ initialization */
-
-void __init lh7a400_init_irq (void)
-{
-       int irq;
-
-       INTC_INTENC = 0xffffffff;       /* Disable all interrupts */
-       GPIO_GPIOFINTEN = 0x00;         /* Disable all GPIOF interrupts */
-       barrier ();
-
-       for (irq = 0; irq < NR_IRQS; ++irq) {
-               switch (irq) {
-               case IRQ_GPIO0INTR:
-               case IRQ_GPIO1INTR:
-               case IRQ_GPIO2INTR:
-               case IRQ_GPIO3INTR:
-               case IRQ_GPIO4INTR:
-               case IRQ_GPIO5INTR:
-               case IRQ_GPIO6INTR:
-               case IRQ_GPIO7INTR:
-                       set_irq_chip (irq, &lh7a400_gpio_chip);
-                       set_irq_handler (irq, handle_level_irq); /* OK default */
-                       break;
-               default:
-                       set_irq_chip (irq, &lh7a400_internal_chip);
-                       set_irq_handler (irq, handle_level_irq);
-               }
-               set_irq_flags (irq, IRQF_VALID);
-       }
-
-       lh7a40x_init_board_irq ();
-
-/* *** FIXME: the LH7a400 does use FIQ interrupts in some cases.  For
-   the time being, these are not initialized. */
-
-/*     init_FIQ(); */
-}
diff --git a/arch/arm/mach-lh7a40x/irq-lh7a404.c b/arch/arm/mach-lh7a40x/irq-lh7a404.c
deleted file mode 100644 (file)
index 14b1733..0000000
+++ /dev/null
@@ -1,175 +0,0 @@
-/* arch/arm/mach-lh7a40x/irq-lh7a404.c
- *
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <mach/irqs.h>
-
-#include "common.h"
-
-#define USE_PRIORITIES
-
-/* See Documentation/arm/Sharp-LH/VectoredInterruptController for more
- * information on using the vectored interrupt controller's
- * prioritizing feature. */
-
-static unsigned char irq_pri_vic1[] = {
-#if defined (USE_PRIORITIES)
-       IRQ_GPIO3INTR,                  /* CPLD */
-       IRQ_DMAM2P4, IRQ_DMAM2P5,       /* AC97 */
-#endif
-};
-static unsigned char irq_pri_vic2[] = {
-#if defined (USE_PRIORITIES)
-       IRQ_T3UI,                       /* Timer */
-       IRQ_GPIO7INTR,                  /* CPLD */
-       IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR,
-       IRQ_LCDINTR,                    /* LCD */
-       IRQ_TSCINTR,                    /* ADC/Touchscreen */
-#endif
-};
-
-  /* CPU IRQ handling */
-
-static void lh7a404_vic1_mask_irq(struct irq_data *d)
-{
-       VIC1_INTENCLR = (1 << d->irq);
-}
-
-static void lh7a404_vic1_unmask_irq(struct irq_data *d)
-{
-       VIC1_INTEN = (1 << d->irq);
-}
-
-static void lh7a404_vic2_mask_irq(struct irq_data *d)
-{
-       VIC2_INTENCLR = (1 << (d->irq - 32));
-}
-
-static void lh7a404_vic2_unmask_irq(struct irq_data *d)
-{
-       VIC2_INTEN = (1 << (d->irq - 32));
-}
-
-static void lh7a404_vic1_ack_gpio_irq(struct irq_data *d)
-{
-       GPIO_GPIOFEOI = (1 << IRQ_TO_GPIO (d->irq));
-       VIC1_INTENCLR = (1 << d->irq);
-}
-
-static void lh7a404_vic2_ack_gpio_irq(struct irq_data *d)
-{
-       GPIO_GPIOFEOI = (1 << IRQ_TO_GPIO (d->irq));
-       VIC2_INTENCLR = (1 << d->irq);
-}
-
-static struct irq_chip lh7a404_vic1_chip = {
-       .name           = "VIC1",
-       .irq_ack        = lh7a404_vic1_mask_irq, /* Because level-triggered */
-       .irq_mask       = lh7a404_vic1_mask_irq,
-       .irq_unmask     = lh7a404_vic1_unmask_irq,
-};
-
-static struct irq_chip lh7a404_vic2_chip = {
-       .name           = "VIC2",
-       .irq_ack        = lh7a404_vic2_mask_irq, /* Because level-triggered */
-       .irq_mask       = lh7a404_vic2_mask_irq,
-       .irq_unmask     = lh7a404_vic2_unmask_irq,
-};
-
-static struct irq_chip lh7a404_gpio_vic1_chip = {
-       .name           = "GPIO-VIC1",
-       .irq_ack        = lh7a404_vic1_ack_gpio_irq,
-       .irq_mask       = lh7a404_vic1_mask_irq,
-       .irq_unmask     = lh7a404_vic1_unmask_irq,
-};
-
-static struct irq_chip lh7a404_gpio_vic2_chip = {
-       .name           = "GPIO-VIC2",
-       .irq_ack        = lh7a404_vic2_ack_gpio_irq,
-       .irq_mask       = lh7a404_vic2_mask_irq,
-       .irq_unmask     = lh7a404_vic2_unmask_irq,
-};
-
-  /* IRQ initialization */
-
-#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
-extern void* branch_irq_lh7a400;
-#endif
-
-void __init lh7a404_init_irq (void)
-{
-       int irq;
-
-#if defined (CONFIG_ARCH_LH7A400) && defined (CONFIG_ARCH_LH7A404)
-#define NOP 0xe1a00000                 /* mov r0, r0 */
-       branch_irq_lh7a400 = NOP;
-#endif
-
-       VIC1_INTENCLR = 0xffffffff;
-       VIC2_INTENCLR = 0xffffffff;
-       VIC1_INTSEL = 0;                /* All IRQs */
-       VIC2_INTSEL = 0;                /* All IRQs */
-       VIC1_NVADDR = VA_VIC1DEFAULT;
-       VIC2_NVADDR = VA_VIC2DEFAULT;
-       VIC1_VECTADDR = 0;
-       VIC2_VECTADDR = 0;
-
-       GPIO_GPIOFINTEN = 0x00;         /* Disable all GPIOF interrupts */
-       barrier ();
-
-               /* Install prioritized interrupts, if there are any. */
-               /* The | 0x20*/
-       for (irq = 0; irq < 16; ++irq) {
-               (&VIC1_VAD0)[irq]
-                       = (irq < ARRAY_SIZE (irq_pri_vic1))
-                       ? (irq_pri_vic1[irq] | VA_VECTORED) : 0;
-               (&VIC1_VECTCNTL0)[irq]
-                       = (irq < ARRAY_SIZE (irq_pri_vic1))
-                       ? (irq_pri_vic1[irq] | VIC_CNTL_ENABLE) : 0;
-               (&VIC2_VAD0)[irq]
-                       = (irq < ARRAY_SIZE (irq_pri_vic2))
-                       ? (irq_pri_vic2[irq] | VA_VECTORED) : 0;
-               (&VIC2_VECTCNTL0)[irq]
-                       = (irq < ARRAY_SIZE (irq_pri_vic2))
-                       ? (irq_pri_vic2[irq] | VIC_CNTL_ENABLE) : 0;
-       }
-
-       for (irq = 0; irq < NR_IRQS; ++irq) {
-               switch (irq) {
-               case IRQ_GPIO0INTR:
-               case IRQ_GPIO1INTR:
-               case IRQ_GPIO2INTR:
-               case IRQ_GPIO3INTR:
-               case IRQ_GPIO4INTR:
-               case IRQ_GPIO5INTR:
-               case IRQ_GPIO6INTR:
-               case IRQ_GPIO7INTR:
-                       set_irq_chip (irq, irq < 32
-                                     ? &lh7a404_gpio_vic1_chip
-                                     : &lh7a404_gpio_vic2_chip);
-                       set_irq_handler (irq, handle_level_irq); /* OK default */
-                       break;
-               default:
-                       set_irq_chip (irq, irq < 32
-                                     ? &lh7a404_vic1_chip
-                                     : &lh7a404_vic2_chip);
-                       set_irq_handler (irq, handle_level_irq);
-               }
-               set_irq_flags (irq, IRQF_VALID);
-       }
-
-       lh7a40x_init_board_irq ();
-}
diff --git a/arch/arm/mach-lh7a40x/irq-lpd7a40x.c b/arch/arm/mach-lh7a40x/irq-lpd7a40x.c
deleted file mode 100644 (file)
index 1bfdcdd..0000000
+++ /dev/null
@@ -1,128 +0,0 @@
-/* arch/arm/mach-lh7a40x/irq-lpd7a40x.c
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <mach/irqs.h>
-
-#include "common.h"
-
-static void lh7a40x_ack_cpld_irq(struct irq_data *d)
-{
-       /* CPLD doesn't have ack capability */
-}
-
-static void lh7a40x_mask_cpld_irq(struct irq_data *d)
-{
-       switch (d->irq) {
-       case IRQ_LPD7A40X_ETH_INT:
-               CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x4;
-               break;
-       case IRQ_LPD7A400_TS:
-               CPLD_INTERRUPTS = CPLD_INTERRUPTS | 0x8;
-               break;
-       }
-}
-
-static void lh7a40x_unmask_cpld_irq(struct irq_data *d)
-{
-       switch (d->irq) {
-       case IRQ_LPD7A40X_ETH_INT:
-               CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x4;
-               break;
-       case IRQ_LPD7A400_TS:
-               CPLD_INTERRUPTS = CPLD_INTERRUPTS & ~ 0x8;
-               break;
-       }
-}
-
-static struct irq_chip lh7a40x_cpld_chip = {
-       .name           = "CPLD",
-       .irq_ack        = lh7a40x_ack_cpld_irq,
-       .irq_mask       = lh7a40x_mask_cpld_irq,
-       .irq_unmask     = lh7a40x_unmask_cpld_irq,
-};
-
-static void lh7a40x_cpld_handler (unsigned int irq, struct irq_desc *desc)
-{
-       unsigned int mask = CPLD_INTERRUPTS;
-
-       desc->irq_data.chip->ack (irq);
-
-       if ((mask & 0x1) == 0)  /* WLAN */
-               generic_handle_irq(IRQ_LPD7A40X_ETH_INT);
-
-       if ((mask & 0x2) == 0)  /* Touch */
-               generic_handle_irq(IRQ_LPD7A400_TS);
-
-       desc->irq_data.chip->unmask (irq); /* Level-triggered need this */
-}
-
-
-  /* IRQ initialization */
-
-void __init lh7a40x_init_board_irq (void)
-{
-       int irq;
-
-               /* Rev A (v2.8): PF0, PF1, PF2, and PF3 are available IRQs.
-                                PF7 supports the CPLD.
-                  Rev B (v3.4): PF0, PF1, and PF2 are available IRQs.
-                                PF3 supports the CPLD.
-                  (Some) LPD7A404 prerelease boards report a version
-                  number of 0x16, but we force an override since the
-                  hardware is of the newer variety.
-               */
-
-       unsigned char cpld_version = CPLD_REVISION;
-       int pinCPLD;
-
-#if defined CONFIG_MACH_LPD7A404
-       cpld_version = 0x34;    /* Override, for now */
-#endif
-       pinCPLD = (cpld_version == 0x28) ? 7 : 3;
-
-               /* First, configure user controlled GPIOF interrupts  */
-
-       GPIO_PFDD       &= ~0x0f; /* PF0-3 are inputs */
-       GPIO_INTTYPE1   &= ~0x0f; /* PF0-3 are level triggered */
-       GPIO_INTTYPE2   &= ~0x0f; /* PF0-3 are active low */
-       barrier ();
-       GPIO_GPIOFINTEN |=  0x0f; /* Enable PF0, PF1, PF2, and PF3 IRQs */
-
-               /* Then, configure CPLD interrupt */
-
-       CPLD_INTERRUPTS =   0x0c; /* Disable all CPLD interrupts */
-       GPIO_PFDD       &= ~(1 << pinCPLD); /* Make input */
-       GPIO_INTTYPE1   |=  (1 << pinCPLD); /* Edge triggered */
-       GPIO_INTTYPE2   &= ~(1 << pinCPLD); /* Active low */
-       barrier ();
-       GPIO_GPIOFINTEN |=  (1 << pinCPLD); /* Enable */
-
-               /* Cascade CPLD interrupts */
-
-       for (irq = IRQ_BOARD_START;
-            irq < IRQ_BOARD_START + NR_IRQ_BOARD; ++irq) {
-               set_irq_chip (irq, &lh7a40x_cpld_chip);
-               set_irq_handler (irq, handle_edge_irq);
-               set_irq_flags (irq, IRQF_VALID);
-       }
-
-       set_irq_chained_handler ((cpld_version == 0x28)
-                                ? IRQ_CPLD_V28
-                                : IRQ_CPLD_V34,
-                                lh7a40x_cpld_handler);
-}
diff --git a/arch/arm/mach-lh7a40x/lcd-panel.h b/arch/arm/mach-lh7a40x/lcd-panel.h
deleted file mode 100644 (file)
index a7f5027..0000000
+++ /dev/null
@@ -1,345 +0,0 @@
-/* lcd-panel.h
-
-   written by Marc Singer
-   18 Jul 2005
-
-   Copyright (C) 2005 Marc Singer
-
-   -----------
-   DESCRIPTION
-   -----------
-
-   Only one panel may be defined at a time.
-
-   The pixel clock is calculated to be no greater than the target.
-
-   Each timing value is accompanied by a specification comment.
-
-     UNITS/MIN/TYP/MAX
-
-   Most of the units will be in clocks.
-
-   USE_RGB555
-
-     Define this macro to configure the AMBA LCD controller to use an
-     RGB555 encoding for the pels instead of the normal RGB565.
-
-   LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
-
-     These boards are best approximated by 555 for all panels.  Some
-     can use an extra low-order bit of blue in bit 16 of the color
-     value, but we don't have a way to communicate this non-linear
-     mapping to the kernel.
-
-*/
-
-#if !defined (__LCD_PANEL_H__)
-#    define   __LCD_PANEL_H__
-
-#if defined (MACH_LPD79520)\
- || defined (MACH_LPD79524)\
- || defined (MACH_LPD7A400)\
- || defined (MACH_LPD7A404)
-# define USE_RGB555
-#endif
-
-struct clcd_panel_extra {
-       unsigned int hrmode;
-       unsigned int clsen;
-       unsigned int spsen;
-       unsigned int pcdel;
-       unsigned int revdel;
-       unsigned int lpdel;
-       unsigned int spldel;
-       unsigned int pc2del;
-};
-
-#define NS_TO_CLOCK(ns,c)      ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
-#define CLOCK_TO_DIV(e,c)      (((c) + (e) - 1)/(e))
-
-#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
-
-       /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
-       /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
-
-#define PIX_CLOCK_TARGET       (6800000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "3.5in QVGA (LQ035Q7DB02)",
-               .xres           = 240,
-               .yres           = 320,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 16,
-               .right_margin   = 21,
-               .upper_margin   = 8,                    // line/8/8/8
-               .lower_margin   = 5,
-               .hsync_len      = 61,
-               .vsync_len      = NS_TO_CLOCK (60, PIX_CLOCK),
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#define HAS_LCD_PANEL_EXTRA
-
-static struct clcd_panel_extra lcd_panel_extra = {
-       .hrmode = 1,
-       .clsen = 1,
-       .spsen = 1,
-       .pcdel = 8,
-       .revdel = 7,
-       .lpdel = 13,
-       .spldel = 77,
-       .pc2del = 208,
-};
-
-#endif
-
-#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
-
-       /* Logic Product Development LCD 5.7" QVGA -10 */
-       /* Sharp PN LQ057Q3DC02 */
-       /* QVGA mode, V/Q=LOW */
-
-/* From Sharp on 2006.1.3.  I believe some of the values are incorrect
- * based on the datasheet.
-
-    Timing0    TIMING1         TIMING2         CONTROL
-    0x140A0C4C 0x080504EF      0x013F380D      0x00000829
-    HBP= 20    VBP=  8         BCD=  0
-    HFP= 10    VFP=  5         CPL=319
-    HSW= 12    VSW=  1         IOE=  0
-    PPL= 19    LPP=239         IPC=  1
-                               IHS=  1
-                               IVS=  1
-                               ACB=  0
-                               CSEL= 0
-                               PCD= 13
-
- */
-
-/* The full horizontal cycle (Th) is clock/360/400/450. */
-/* The full vertical   cycle (Tv) is line/251/262/280. */
-
-#define PIX_CLOCK_TARGET       (6300000) /* -/6.3/7 MHz */
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "5.7in QVGA (LQ057Q3DC02)",
-               .xres           = 320,
-               .yres           = 240,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 11,
-               .right_margin   = 400-11-320-2,
-               .upper_margin   = 7,                    // line/7/7/7
-               .lower_margin   = 262-7-240-2,
-               .hsync_len      = 2,                    // clk/2/96/200
-               .vsync_len      = 2,                    // line/2/-/34
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
-
-       /* Logic Product Development LCD 6.4" VGA -10 */
-       /* Sharp PN LQ64D343 */
-
-/* The full horizontal cycle (Th) is clock/750/800/900. */
-/* The full vertical   cycle (Tv) is line/515/525/560. */
-
-#define PIX_CLOCK_TARGET       (28330000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "6.4in QVGA (LQ64D343)",
-               .xres           = 640,
-               .yres           = 480,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 32,
-               .right_margin   = 800-32-640-96,
-               .upper_margin   = 32,                   // line/34/34/34
-               .lower_margin   = 540-32-480-2,
-               .hsync_len      = 96,                   // clk/2/96/200
-               .vsync_len      = 2,                    // line/2/-/34
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
-
-       /* Logic Product Development LCD 10.4" VGA -10 */
-       /* Sharp PN LQ10D368 */
-
-#define PIX_CLOCK_TARGET       (28330000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "10.4in VGA (LQ10D368)",
-               .xres           = 640,
-               .yres           = 480,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 21,
-               .right_margin   = 15,
-               .upper_margin   = 34,
-               .lower_margin   = 5,
-               .hsync_len      = 96,
-               .vsync_len      = 16,
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
-
-       /* Logic Product Development LCD 12.1" SVGA -10 */
-       /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
-
-/* Note that with a 99993900 Hz HCLK, it is not possible to hit the
- * target clock frequency range of 35MHz to 42MHz. */
-
-/* If the target pixel clock is substantially lower than the panel
- * spec, this is done to prevent the LCD display from glitching when
- * the CPU is under load.  A pixel clock higher than 25MHz
- * (empirically determined) will compete with the CPU for bus cycles
- * for the Ethernet chip.  However, even a pixel clock of 10MHz
- * competes with Compact Flash interface during some operations
- * (fdisk, e2fsck).  And, at that speed the display may have a visible
- * flicker. */
-
-/* The full horizontal cycle (Th) is clock/832/1056/1395. */
-
-#define PIX_CLOCK_TARGET       (20000000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "12.1in SVGA (LQ121S1DG41)",
-               .xres           = 800,
-               .yres           = 600,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 89,           // ns/5/-/(1/PIX_CLOCK)-10
-               .right_margin   = 1056-800-89-128,
-               .upper_margin   = 23,           // line/23/23/23
-               .lower_margin   = 44,
-               .hsync_len      = 128,          // clk/2/128/200
-               .vsync_len      = 4,            // line/2/4/6
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-#if defined CONFIG_FB_ARMCLCD_HITACHI
-
-       /* Hitachi*/
-       /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
-
-#define PIX_CLOCK_TARGET       (49000000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "Hitachi 800x480",
-               .xres           = 800,
-               .yres           = 480,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 88,
-               .right_margin   = 40,
-               .upper_margin   = 32,
-               .lower_margin   = 11,
-               .hsync_len      = 128,
-               .vsync_len      = 2,
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IPC | TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-
-#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
-
-       /* AU Optotronics  A070VW01 7.0 Wide Screen color Display*/
-       /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
-
-#define PIX_CLOCK_TARGET       (10000000)
-#define PIX_CLOCK_DIVIDER      CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
-#define PIX_CLOCK              (HCLK/PIX_CLOCK_DIVIDER)
-
-static struct clcd_panel lcd_panel = {
-       .mode   = {
-               .name           = "7.0in Wide (A070VW01)",
-               .xres           = 480,
-               .yres           = 234,
-               .pixclock       = PIX_CLOCK,
-               .left_margin    = 30,
-               .right_margin   = 25,
-               .upper_margin   = 14,
-               .lower_margin   = 12,
-               .hsync_len      = 100,
-               .vsync_len      = 1,
-               .vmode          = FB_VMODE_NONINTERLACED,
-       },
-       .width          = -1,
-       .height         = -1,
-       .tim2           = TIM2_IPC | TIM2_IHS | TIM2_IVS
-                       | (PIX_CLOCK_DIVIDER - 2),
-       .cntl           = CNTL_LCDTFT | CNTL_WATERMARK,
-       .bpp            = 16,
-};
-
-#endif
-
-#undef NS_TO_CLOCK
-#undef CLOCK_TO_DIV
-
-#endif  /* __LCD_PANEL_H__ */
diff --git a/arch/arm/mach-lh7a40x/ssp-cpld.c b/arch/arm/mach-lh7a40x/ssp-cpld.c
deleted file mode 100644 (file)
index 2901d49..0000000
+++ /dev/null
@@ -1,343 +0,0 @@
-/* arch/arm/mach-lh7a40x/ssp-cpld.c
- *
- *  Copyright (C) 2004,2005 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- * SSP/SPI driver for the CardEngine CPLD.
- *
- */
-
-/* NOTES
-   -----
-
-   o *** This driver is cribbed from the 7952x implementation.
-        Some comments may not apply.
-
-   o This driver contains sufficient logic to control either the
-     serial EEPROMs or the audio codec.  It is included in the kernel
-     to support the codec.  The EEPROMs are really the responsibility
-     of the boot loader and should probably be left alone.
-
-   o The code must be augmented to cope with multiple, simultaneous
-     clients.
-     o The audio codec writes to the codec chip whenever playback
-       starts.
-     o The touchscreen driver writes to the ads chip every time it
-       samples.
-     o The audio codec must write 16 bits, but the touch chip writes
-       are 8 bits long.
-     o We need to be able to keep these configurations separate while
-       simultaneously active.
-
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-//#include <linux/sched.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-//#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <mach/ssp.h>
-
-//#define TALK
-
-#if defined (TALK)
-#define PRINTK(f...)           printk (f)
-#else
-#define PRINTK(f...)           do {} while (0)
-#endif
-
-#if defined (CONFIG_ARCH_LH7A400)
-# define CPLD_SPID             __REGP16(CPLD06_VIRT) /* SPI data */
-# define CPLD_SPIC             __REGP16(CPLD08_VIRT) /* SPI control */
-# define CPLD_SPIC_CS_CODEC    (1<<0)
-# define CPLD_SPIC_CS_TOUCH    (1<<1)
-# define CPLD_SPIC_WRITE       (0<<2)
-# define CPLD_SPIC_READ                (1<<2)
-# define CPLD_SPIC_DONE                (1<<3) /* r/o */
-# define CPLD_SPIC_LOAD                (1<<4)
-# define CPLD_SPIC_START       (1<<4)
-# define CPLD_SPIC_LOADED      (1<<5) /* r/o */
-#endif
-
-#define CPLD_SPI               __REGP16(CPLD0A_VIRT) /* SPI operation */
-#define CPLD_SPI_CS_EEPROM     (1<<3)
-#define CPLD_SPI_SCLK          (1<<2)
-#define CPLD_SPI_TX_SHIFT      (1)
-#define CPLD_SPI_TX            (1<<CPLD_SPI_TX_SHIFT)
-#define CPLD_SPI_RX_SHIFT      (0)
-#define CPLD_SPI_RX            (1<<CPLD_SPI_RX_SHIFT)
-
-/* *** FIXME: these timing values are substantially larger than the
-   *** chip requires. We may implement an nsleep () function. */
-#define T_SKH  1               /* Clock time high (us) */
-#define T_SKL  1               /* Clock time low (us) */
-#define T_CS   1               /* Minimum chip select low time (us)  */
-#define T_CSS  1               /* Minimum chip select setup time (us)  */
-#define T_DIS  1               /* Data setup time (us) */
-
-        /* EEPROM SPI bits */
-#define P_START                (1<<9)
-#define P_WRITE                (1<<7)
-#define P_READ         (2<<7)
-#define P_ERASE                (3<<7)
-#define P_EWDS         (0<<7)
-#define P_WRAL         (0<<7)
-#define P_ERAL         (0<<7)
-#define P_EWEN         (0<<7)
-#define P_A_EWDS       (0<<5)
-#define P_A_WRAL       (1<<5)
-#define P_A_ERAL       (2<<5)
-#define P_A_EWEN       (3<<5)
-
-struct ssp_configuration {
-       int device;
-       int mode;
-       int speed;
-       int frame_size_write;
-       int frame_size_read;
-};
-
-static struct ssp_configuration ssp_configuration;
-static spinlock_t ssp_lock;
-
-static void enable_cs (void)
-{
-       switch (ssp_configuration.device) {
-       case DEVICE_EEPROM:
-               CPLD_SPI |= CPLD_SPI_CS_EEPROM;
-               break;
-       }
-       udelay (T_CSS);
-}
-
-static void disable_cs (void)
-{
-       switch (ssp_configuration.device) {
-       case DEVICE_EEPROM:
-               CPLD_SPI &= ~CPLD_SPI_CS_EEPROM;
-               break;
-       }
-       udelay (T_CS);
-}
-
-static void pulse_clock (void)
-{
-       CPLD_SPI |=  CPLD_SPI_SCLK;
-       udelay (T_SKH);
-       CPLD_SPI &= ~CPLD_SPI_SCLK;
-       udelay (T_SKL);
-}
-
-
-/* execute_spi_command
-
-   sends an spi command to a device.  It first sends cwrite bits from
-   v.  If cread is greater than zero it will read cread bits
-   (discarding the leading 0 bit) and return them.  If cread is less
-   than zero it will check for completetion status and return 0 on
-   success or -1 on timeout.  If cread is zero it does nothing other
-   than sending the command.
-
-   On the LPD7A400, we can only read or write multiples of 8 bits on
-   the codec and the touch screen device.  Here, we round up.
-
-*/
-
-static int execute_spi_command (int v, int cwrite, int cread)
-{
-       unsigned long l = 0;
-
-#if defined (CONFIG_MACH_LPD7A400)
-       /* The codec and touch devices cannot be bit-banged.  Instead,
-        * the CPLD provides an eight-bit shift register and a crude
-        * interface.  */
-       if (   ssp_configuration.device == DEVICE_CODEC
-           || ssp_configuration.device == DEVICE_TOUCH) {
-               int select = 0;
-
-               PRINTK ("spi(%d %d.%d) 0x%04x",
-                       ssp_configuration.device, cwrite, cread,
-                       v);
-#if defined (TALK)
-               if (ssp_configuration.device == DEVICE_CODEC)
-                       PRINTK (" 0x%03x -> %2d", v & 0x1ff, (v >> 9) & 0x7f);
-#endif
-               PRINTK ("\n");
-
-               if (ssp_configuration.device == DEVICE_CODEC)
-                       select = CPLD_SPIC_CS_CODEC;
-               if (ssp_configuration.device == DEVICE_TOUCH)
-                       select = CPLD_SPIC_CS_TOUCH;
-               if (cwrite) {
-                       for (cwrite = (cwrite + 7)/8; cwrite-- > 0; ) {
-                               CPLD_SPID = (v >> (8*cwrite)) & 0xff;
-                               CPLD_SPIC = select | CPLD_SPIC_LOAD;
-                               while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
-                                       ;
-                               CPLD_SPIC = select;
-                               while (!(CPLD_SPIC & CPLD_SPIC_DONE))
-                                       ;
-                       }
-                       v = 0;
-               }
-               if (cread) {
-                       mdelay (2);     /* *** FIXME: required by ads7843? */
-                       v = 0;
-                       for (cread = (cread + 7)/8; cread-- > 0;) {
-                               CPLD_SPID = 0;
-                               CPLD_SPIC = select | CPLD_SPIC_READ
-                                       | CPLD_SPIC_START;
-                               while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
-                                       ;
-                               CPLD_SPIC = select | CPLD_SPIC_READ;
-                               while (!(CPLD_SPIC & CPLD_SPIC_DONE))
-                                       ;
-                               v = (v << 8) | CPLD_SPID;
-                       }
-               }
-               return v;
-       }
-#endif
-
-       PRINTK ("spi(%d) 0x%04x -> 0x%x\r\n", ssp_configuration.device,
-               v & 0x1ff, (v >> 9) & 0x7f);
-
-       enable_cs ();
-
-       v <<= CPLD_SPI_TX_SHIFT; /* Correction for position of SPI_TX bit */
-       while (cwrite--) {
-               CPLD_SPI
-                       = (CPLD_SPI & ~CPLD_SPI_TX)
-                       | ((v >> cwrite) & CPLD_SPI_TX);
-               udelay (T_DIS);
-               pulse_clock ();
-       }
-
-       if (cread < 0) {
-               int delay = 10;
-               disable_cs ();
-               udelay (1);
-               enable_cs ();
-
-               l = -1;
-               do {
-                       if (CPLD_SPI & CPLD_SPI_RX) {
-                               l = 0;
-                               break;
-                       }
-               } while (udelay (1), --delay);
-       }
-       else
-       /* We pulse the clock before the data to skip the leading zero. */
-               while (cread-- > 0) {
-                       pulse_clock ();
-                       l = (l<<1)
-                               | (((CPLD_SPI & CPLD_SPI_RX)
-                                   >> CPLD_SPI_RX_SHIFT) & 0x1);
-               }
-
-       disable_cs ();
-       return l;
-}
-
-static int ssp_init (void)
-{
-       spin_lock_init (&ssp_lock);
-       memset (&ssp_configuration, 0, sizeof (ssp_configuration));
-       return 0;
-}
-
-
-/* ssp_chip_select
-
-   drops the chip select line for the CPLD shift-register controlled
-   devices.  It doesn't enable chip
-
-*/
-
-static void ssp_chip_select (int enable)
-{
-#if defined (CONFIG_MACH_LPD7A400)
-       int select;
-
-       if (ssp_configuration.device == DEVICE_CODEC)
-               select = CPLD_SPIC_CS_CODEC;
-       else if (ssp_configuration.device == DEVICE_TOUCH)
-               select = CPLD_SPIC_CS_TOUCH;
-       else
-               return;
-
-       if (enable)
-               CPLD_SPIC = select;
-       else
-               CPLD_SPIC = 0;
-#endif
-}
-
-static void ssp_acquire (void)
-{
-       spin_lock (&ssp_lock);
-}
-
-static void ssp_release (void)
-{
-       ssp_chip_select (0);    /* just in case */
-       spin_unlock (&ssp_lock);
-}
-
-static int ssp_configure (int device, int mode, int speed,
-                          int frame_size_write, int frame_size_read)
-{
-       ssp_configuration.device                = device;
-       ssp_configuration.mode                  = mode;
-       ssp_configuration.speed                 = speed;
-       ssp_configuration.frame_size_write      = frame_size_write;
-       ssp_configuration.frame_size_read       = frame_size_read;
-
-       return 0;
-}
-
-static int ssp_read (void)
-{
-       return execute_spi_command (0, 0, ssp_configuration.frame_size_read);
-}
-
-static int ssp_write (u16 data)
-{
-       execute_spi_command (data, ssp_configuration.frame_size_write, 0);
-       return 0;
-}
-
-static int ssp_write_read (u16 data)
-{
-       return execute_spi_command (data, ssp_configuration.frame_size_write,
-                                   ssp_configuration.frame_size_read);
-}
-
-struct ssp_driver lh7a40x_cpld_ssp_driver = {
-       .init           = ssp_init,
-       .acquire        = ssp_acquire,
-       .release        = ssp_release,
-       .configure      = ssp_configure,
-       .chip_select    = ssp_chip_select,
-       .read           = ssp_read,
-       .write          = ssp_write,
-       .write_read     = ssp_write_read,
-};
-
-
-MODULE_AUTHOR("Marc Singer");
-MODULE_DESCRIPTION("LPD7A40X CPLD SPI driver");
-MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-lh7a40x/time.c b/arch/arm/mach-lh7a40x/time.c
deleted file mode 100644 (file)
index 4601e42..0000000
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- *  arch/arm/mach-lh7a40x/time.c
- *
- *  Copyright (C) 2004 Logic Product Development
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/time.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/leds.h>
-
-#include <asm/mach/time.h>
-#include "common.h"
-
-#if HZ < 100
-# define TIMER_CONTROL TIMER_CONTROL2
-# define TIMER_LOAD    TIMER_LOAD2
-# define TIMER_CONSTANT        (508469/HZ)
-# define TIMER_MODE    (TIMER_C_ENABLE | TIMER_C_PERIODIC | TIMER_C_508KHZ)
-# define TIMER_EOI     TIMER_EOI2
-# define TIMER_IRQ     IRQ_T2UI
-#else
-# define TIMER_CONTROL TIMER_CONTROL3
-# define TIMER_LOAD    TIMER_LOAD3
-# define TIMER_CONSTANT        (3686400/HZ)
-# define TIMER_MODE    (TIMER_C_ENABLE | TIMER_C_PERIODIC)
-# define TIMER_EOI     TIMER_EOI3
-# define TIMER_IRQ     IRQ_T3UI
-#endif
-
-static irqreturn_t
-lh7a40x_timer_interrupt(int irq, void *dev_id)
-{
-       TIMER_EOI = 0;
-       timer_tick();
-
-       return IRQ_HANDLED;
-}
-
-static struct irqaction lh7a40x_timer_irq = {
-       .name           = "LHA740x Timer Tick",
-       .flags          = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-       .handler        = lh7a40x_timer_interrupt,
-};
-
-static void __init lh7a40x_timer_init (void)
-{
-                               /* Stop/disable all timers */
-       TIMER_CONTROL1 = 0;
-       TIMER_CONTROL2 = 0;
-       TIMER_CONTROL3 = 0;
-
-       setup_irq (TIMER_IRQ, &lh7a40x_timer_irq);
-
-       TIMER_LOAD = TIMER_CONSTANT;
-       TIMER_CONTROL = TIMER_MODE;
-}
-
-struct sys_timer lh7a40x_timer = {
-       .init           = &lh7a40x_timer_init,
-};
index ee747919a766edc963206d1a93296a549baee4b3..68d48ab6eacf85149af6731f04bb732b27c93f36 100644 (file)
@@ -206,68 +206,6 @@ SMC_outw(u16 val, void __iomem *ioaddr, int reg)
 #define RPC_LSA_DEFAULT                RPC_LED_TX_RX
 #define RPC_LSB_DEFAULT                RPC_LED_100_10
 
-#elif   defined(CONFIG_MACH_LPD79520) ||       \
-       defined(CONFIG_MACH_LPD7A400) ||        \
-       defined(CONFIG_MACH_LPD7A404)
-
-/* The LPD7X_IOBARRIER is necessary to overcome a mismatch between the
- * way that the CPU handles chip selects and the way that the SMC chip
- * expects the chip select to operate.  Refer to
- * Documentation/arm/Sharp-LH/IOBarrier for details.  The read from
- * IOBARRIER is a byte, in order that we read the least-common
- * denominator.  It would be wasteful to read 32 bits from an 8-bit
- * accessible region.
- *
- * There is no explicit protection against interrupts intervening
- * between the writew and the IOBARRIER.  In SMC ISR there is a
- * preamble that performs an IOBARRIER in the extremely unlikely event
- * that the driver interrupts itself between a writew to the chip an
- * the IOBARRIER that follows *and* the cache is large enough that the
- * first off-chip access while handing the interrupt is to the SMC
- * chip.  Other devices in the same address space as the SMC chip must
- * be aware of the potential for trouble and perform a similar
- * IOBARRIER on entry to their ISR.
- */
-
-#include <mach/constants.h>    /* IOBARRIER_VIRT */
-
-#define SMC_CAN_USE_8BIT       0
-#define SMC_CAN_USE_16BIT      1
-#define SMC_CAN_USE_32BIT      0
-#define SMC_NOWAIT             0
-#define LPD7X_IOBARRIER                readb (IOBARRIER_VIRT)
-
-#define SMC_inw(a,r)\
-   ({ unsigned short v = readw ((void*) ((a) + (r))); LPD7X_IOBARRIER; v; })
-#define SMC_outw(v,a,r)          ({ writew ((v), (a) + (r)); LPD7X_IOBARRIER; })
-
-#define SMC_insw               LPD7_SMC_insw
-static inline void LPD7_SMC_insw (unsigned char* a, int r,
-                                 unsigned char* p, int l)
-{
-       unsigned short* ps = (unsigned short*) p;
-       while (l-- > 0) {
-               *ps++ = readw (a + r);
-               LPD7X_IOBARRIER;
-       }
-}
-
-#define SMC_outsw              LPD7_SMC_outsw
-static inline void LPD7_SMC_outsw (unsigned char* a, int r,
-                                  unsigned char* p, int l)
-{
-       unsigned short* ps = (unsigned short*) p;
-       while (l-- > 0) {
-               writew (*ps++, a + r);
-               LPD7X_IOBARRIER;
-       }
-}
-
-#define SMC_INTERRUPT_PREAMBLE LPD7X_IOBARRIER
-
-#define RPC_LSA_DEFAULT                RPC_LED_TX_RX
-#define RPC_LSB_DEFAULT                RPC_LED_100_10
-
 #elif  defined(CONFIG_ARCH_VERSATILE)
 
 #define SMC_CAN_USE_8BIT       1
index b1682d7f1d8a2492ad59aea18622cb4294b71813..1174d4d90407ca4b38d056204a3aaee7efa96b4e 100644 (file)
@@ -1110,29 +1110,6 @@ config SERIAL_PMACZILOG_CONSOLE
          on your (Power)Mac as the console, you can do so by answering
          Y to this option.
 
-config SERIAL_LH7A40X
-       tristate "Sharp LH7A40X embedded UART support"
-       depends on ARM && ARCH_LH7A40X
-       select SERIAL_CORE
-       help
-         This enables support for the three on-board UARTs of the
-         Sharp LH7A40X series CPUs.  Choose Y or M.
-
-config SERIAL_LH7A40X_CONSOLE
-       bool "Support for console on Sharp LH7A40X serial port"
-       depends on SERIAL_LH7A40X=y
-       select SERIAL_CORE_CONSOLE
-       help
-         Say Y here if you wish to use one of the serial ports as the
-         system console--the system console is the device which
-         receives all kernel messages and warnings and which allows
-         logins in single user mode.
-
-         Even if you say Y here, the currently visible framebuffer console
-         (/dev/tty0) will still be used as the default system console, but
-         you can alter that using a kernel command line, for example
-         "console=ttyAM1".
-
 config SERIAL_CPM
        tristate "CPM SCC/SMC serial port support"
        depends on CPM2 || 8xx
index 8ea92e9c73b046cb66cb43ee3d6daa9ddd3049ab..8e325408b1a6b77dbfbe8d4219f6a2a658b514a1 100644 (file)
@@ -54,7 +54,6 @@ obj-$(CONFIG_SERIAL_68328) += 68328serial.o
 obj-$(CONFIG_SERIAL_68360) += 68360serial.o
 obj-$(CONFIG_SERIAL_MCF) += mcf.o
 obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
-obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
 obj-$(CONFIG_SERIAL_DZ) += dz.o
 obj-$(CONFIG_SERIAL_ZS) += zs.o
 obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
diff --git a/drivers/tty/serial/serial_lh7a40x.c b/drivers/tty/serial/serial_lh7a40x.c
deleted file mode 100644 (file)
index ea74470..0000000
+++ /dev/null
@@ -1,682 +0,0 @@
-/* drivers/serial/serial_lh7a40x.c
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-/* Driver for Sharp LH7A40X embedded serial ports
- *
- *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
- *  Based on drivers/serial/amba.c, by Deep Blue Solutions Ltd.
- *
- *  ---
- *
- * This driver supports the embedded UARTs of the Sharp LH7A40X series
- * CPUs.  While similar to the 16550 and other UART chips, there is
- * nothing close to register compatibility.  Moreover, some of the
- * modem control lines are not available, either in the chip or they
- * are lacking in the board-level implementation.
- *
- * - Use of SIRDIS
- *   For simplicity, we disable the IR functions of any UART whenever
- *   we enable it.
- *
- */
-
-
-#if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#define DEV_MAJOR      204
-#define DEV_MINOR      16
-#define DEV_NR         3
-
-#define ISR_LOOP_LIMIT 256
-
-#define UR(p,o)        _UR ((p)->membase, o)
-#define _UR(b,o) (*((volatile unsigned int*)(((unsigned char*) b) + (o))))
-#define BIT_CLR(p,o,m) UR(p,o) = UR(p,o) & (~(unsigned int)m)
-#define BIT_SET(p,o,m) UR(p,o) = UR(p,o) | ( (unsigned int)m)
-
-#define UART_REG_SIZE  32
-
-#define UART_R_DATA    (0x00)
-#define UART_R_FCON    (0x04)
-#define UART_R_BRCON   (0x08)
-#define UART_R_CON     (0x0c)
-#define UART_R_STATUS  (0x10)
-#define UART_R_RAWISR  (0x14)
-#define UART_R_INTEN   (0x18)
-#define UART_R_ISR     (0x1c)
-
-#define UARTEN         (0x01)          /* UART enable */
-#define SIRDIS         (0x02)          /* Serial IR disable (UART1 only) */
-
-#define RxEmpty                (0x10)
-#define TxEmpty                (0x80)
-#define TxFull         (0x20)
-#define nRxRdy         RxEmpty
-#define nTxRdy         TxFull
-#define TxBusy         (0x08)
-
-#define RxBreak                (0x0800)
-#define RxOverrunError (0x0400)
-#define RxParityError  (0x0200)
-#define RxFramingError (0x0100)
-#define RxError     (RxBreak | RxOverrunError | RxParityError | RxFramingError)
-
-#define DCD            (0x04)
-#define DSR            (0x02)
-#define CTS            (0x01)
-
-#define RxInt          (0x01)
-#define TxInt          (0x02)
-#define ModemInt       (0x04)
-#define RxTimeoutInt   (0x08)
-
-#define MSEOI          (0x10)
-
-#define WLEN_8         (0x60)
-#define WLEN_7         (0x40)
-#define WLEN_6         (0x20)
-#define WLEN_5         (0x00)
-#define WLEN           (0x60)  /* Mask for all word-length bits */
-#define STP2           (0x08)
-#define PEN            (0x02)  /* Parity Enable */
-#define EPS            (0x04)  /* Even Parity Set */
-#define FEN            (0x10)  /* FIFO Enable */
-#define BRK            (0x01)  /* Send Break */
-
-
-struct uart_port_lh7a40x {
-       struct uart_port port;
-       unsigned int statusPrev; /* Most recently read modem status */
-};
-
-static void lh7a40xuart_stop_tx (struct uart_port* port)
-{
-       BIT_CLR (port, UART_R_INTEN, TxInt);
-}
-
-static void lh7a40xuart_start_tx (struct uart_port* port)
-{
-       BIT_SET (port, UART_R_INTEN, TxInt);
-
-       /* *** FIXME: do I need to check for startup of the
-                     transmitter?  The old driver did, but AMBA
-                     doesn't . */
-}
-
-static void lh7a40xuart_stop_rx (struct uart_port* port)
-{
-       BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
-}
-
-static void lh7a40xuart_enable_ms (struct uart_port* port)
-{
-       BIT_SET (port, UART_R_INTEN, ModemInt);
-}
-
-static void lh7a40xuart_rx_chars (struct uart_port* port)
-{
-       struct tty_struct* tty = port->state->port.tty;
-       int cbRxMax = 256;      /* (Gross) limit on receive */
-       unsigned int data;      /* Received data and status */
-       unsigned int flag;
-
-       while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
-               data = UR (port, UART_R_DATA);
-               flag = TTY_NORMAL;
-               ++port->icount.rx;
-
-               if (unlikely(data & RxError)) {
-                       if (data & RxBreak) {
-                               data &= ~(RxFramingError | RxParityError);
-                               ++port->icount.brk;
-                               if (uart_handle_break (port))
-                                       continue;
-                       }
-                       else if (data & RxParityError)
-                               ++port->icount.parity;
-                       else if (data & RxFramingError)
-                               ++port->icount.frame;
-                       if (data & RxOverrunError)
-                               ++port->icount.overrun;
-
-                               /* Mask by termios, leave Rx'd byte */
-                       data &= port->read_status_mask | 0xff;
-
-                       if (data & RxBreak)
-                               flag = TTY_BREAK;
-                       else if (data & RxParityError)
-                               flag = TTY_PARITY;
-                       else if (data & RxFramingError)
-                               flag = TTY_FRAME;
-               }
-
-               if (uart_handle_sysrq_char (port, (unsigned char) data))
-                       continue;
-
-               uart_insert_char(port, data, RxOverrunError, data, flag);
-       }
-       tty_flip_buffer_push (tty);
-       return;
-}
-
-static void lh7a40xuart_tx_chars (struct uart_port* port)
-{
-       struct circ_buf* xmit = &port->state->xmit;
-       int cbTxMax = port->fifosize;
-
-       if (port->x_char) {
-               UR (port, UART_R_DATA) = port->x_char;
-               ++port->icount.tx;
-               port->x_char = 0;
-               return;
-       }
-       if (uart_circ_empty (xmit) || uart_tx_stopped (port)) {
-               lh7a40xuart_stop_tx (port);
-               return;
-       }
-
-       /* Unlike the AMBA UART, the lh7a40x UART does not guarantee
-          that at least half of the FIFO is empty.  Instead, we check
-          status for every character.  Using the AMBA method causes
-          the transmitter to drop characters. */
-
-       do {
-               UR (port, UART_R_DATA) = xmit->buf[xmit->tail];
-               xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-               ++port->icount.tx;
-               if (uart_circ_empty(xmit))
-                       break;
-       } while (!(UR (port, UART_R_STATUS) & nTxRdy)
-                && cbTxMax--);
-
-       if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS)
-               uart_write_wakeup (port);
-
-       if (uart_circ_empty (xmit))
-               lh7a40xuart_stop_tx (port);
-}
-
-static void lh7a40xuart_modem_status (struct uart_port* port)
-{
-       unsigned int status = UR (port, UART_R_STATUS);
-       unsigned int delta
-               = status ^ ((struct uart_port_lh7a40x*) port)->statusPrev;
-
-       BIT_SET (port, UART_R_RAWISR, MSEOI); /* Clear modem status intr */
-
-       if (!delta)             /* Only happens if we missed 2 transitions */
-               return;
-
-       ((struct uart_port_lh7a40x*) port)->statusPrev = status;
-
-       if (delta & DCD)
-               uart_handle_dcd_change (port, status & DCD);
-
-       if (delta & DSR)
-               ++port->icount.dsr;
-
-       if (delta & CTS)
-               uart_handle_cts_change (port, status & CTS);
-
-       wake_up_interruptible (&port->state->port.delta_msr_wait);
-}
-
-static irqreturn_t lh7a40xuart_int (int irq, void* dev_id)
-{
-       struct uart_port* port = dev_id;
-       unsigned int cLoopLimit = ISR_LOOP_LIMIT;
-       unsigned int isr = UR (port, UART_R_ISR);
-
-
-       do {
-               if (isr & (RxInt | RxTimeoutInt))
-                       lh7a40xuart_rx_chars(port);
-               if (isr & ModemInt)
-                       lh7a40xuart_modem_status (port);
-               if (isr & TxInt)
-                       lh7a40xuart_tx_chars (port);
-
-               if (--cLoopLimit == 0)
-                       break;
-
-               isr = UR (port, UART_R_ISR);
-       } while (isr & (RxInt | TxInt | RxTimeoutInt));
-
-       return IRQ_HANDLED;
-}
-
-static unsigned int lh7a40xuart_tx_empty (struct uart_port* port)
-{
-       return (UR (port, UART_R_STATUS) & TxEmpty) ? TIOCSER_TEMT : 0;
-}
-
-static unsigned int lh7a40xuart_get_mctrl (struct uart_port* port)
-{
-       unsigned int result = 0;
-       unsigned int status = UR (port, UART_R_STATUS);
-
-       if (status & DCD)
-               result |= TIOCM_CAR;
-       if (status & DSR)
-               result |= TIOCM_DSR;
-       if (status & CTS)
-               result |= TIOCM_CTS;
-
-       return result;
-}
-
-static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl)
-{
-       /* None of the ports supports DTR. UART1 supports RTS through GPIO. */
-       /* Note, kernel appears to be setting DTR and RTS on console. */
-
-       /* *** FIXME: this deserves more work.  There's some work in
-              tracing all of the IO pins. */
-#if 0
-       if( port->mapbase == UART1_PHYS) {
-               gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
-
-               if (mctrl & TIOCM_RTS)
-                       gpio->pbdr &= ~GPIOB_UART1_RTS;
-               else
-                       gpio->pbdr |= GPIOB_UART1_RTS;
-       }
-#endif
-}
-
-static void lh7a40xuart_break_ctl (struct uart_port* port, int break_state)
-{
-       unsigned long flags;
-
-       spin_lock_irqsave(&port->lock, flags);
-       if (break_state == -1)
-               BIT_SET (port, UART_R_FCON, BRK); /* Assert break */
-       else
-               BIT_CLR (port, UART_R_FCON, BRK); /* Deassert break */
-       spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static int lh7a40xuart_startup (struct uart_port* port)
-{
-       int retval;
-
-       retval = request_irq (port->irq, lh7a40xuart_int, 0,
-                             "serial_lh7a40x", port);
-       if (retval)
-               return retval;
-
-                               /* Initial modem control-line settings */
-       ((struct uart_port_lh7a40x*) port)->statusPrev
-               = UR (port, UART_R_STATUS);
-
-       /* There is presently no configuration option to enable IR.
-          Thus, we always disable it. */
-
-       BIT_SET (port, UART_R_CON, UARTEN | SIRDIS);
-       BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
-
-       return 0;
-}
-
-static void lh7a40xuart_shutdown (struct uart_port* port)
-{
-       free_irq (port->irq, port);
-       BIT_CLR (port, UART_R_FCON, BRK | FEN);
-       BIT_CLR (port, UART_R_CON, UARTEN);
-}
-
-static void lh7a40xuart_set_termios (struct uart_port* port,
-                                    struct ktermios* termios,
-                                    struct ktermios* old)
-{
-       unsigned int con;
-       unsigned int inten;
-       unsigned int fcon;
-       unsigned long flags;
-       unsigned int baud;
-       unsigned int quot;
-
-       baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16);
-       quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */
-
-       switch (termios->c_cflag & CSIZE) {
-       case CS5:
-               fcon = WLEN_5;
-               break;
-       case CS6:
-               fcon = WLEN_6;
-               break;
-       case CS7:
-               fcon = WLEN_7;
-               break;
-       case CS8:
-       default:
-               fcon = WLEN_8;
-               break;
-       }
-       if (termios->c_cflag & CSTOPB)
-               fcon |= STP2;
-       if (termios->c_cflag & PARENB) {
-               fcon |= PEN;
-               if (!(termios->c_cflag & PARODD))
-                       fcon |= EPS;
-       }
-       if (port->fifosize > 1)
-               fcon |= FEN;
-
-       spin_lock_irqsave (&port->lock, flags);
-
-       uart_update_timeout (port, termios->c_cflag, baud);
-
-       port->read_status_mask = RxOverrunError;
-       if (termios->c_iflag & INPCK)
-               port->read_status_mask |= RxFramingError | RxParityError;
-       if (termios->c_iflag & (BRKINT | PARMRK))
-               port->read_status_mask |= RxBreak;
-
-               /* Figure mask for status we ignore */
-       port->ignore_status_mask = 0;
-       if (termios->c_iflag & IGNPAR)
-               port->ignore_status_mask |= RxFramingError | RxParityError;
-       if (termios->c_iflag & IGNBRK) {
-               port->ignore_status_mask |= RxBreak;
-               /* Ignore overrun when ignorning parity */
-               /* *** FIXME: is this in the right place? */
-               if (termios->c_iflag & IGNPAR)
-                       port->ignore_status_mask |= RxOverrunError;
-       }
-
-               /* Ignore all receive errors when receive disabled */
-       if ((termios->c_cflag & CREAD) == 0)
-               port->ignore_status_mask |= RxError;
-
-       con   = UR (port, UART_R_CON);
-       inten = (UR (port, UART_R_INTEN) & ~ModemInt);
-
-       if (UART_ENABLE_MS (port, termios->c_cflag))
-               inten |= ModemInt;
-
-       BIT_CLR (port, UART_R_CON, UARTEN);     /* Disable UART */
-       UR (port, UART_R_INTEN) = 0;            /* Disable interrupts */
-       UR (port, UART_R_BRCON) = quot - 1;     /* Set baud rate divisor */
-       UR (port, UART_R_FCON)  = fcon;         /* Set FIFO and frame ctrl */
-       UR (port, UART_R_INTEN) = inten;        /* Enable interrupts */
-       UR (port, UART_R_CON)   = con;          /* Restore UART mode */
-
-       spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static const char* lh7a40xuart_type (struct uart_port* port)
-{
-       return port->type == PORT_LH7A40X ? "LH7A40X" : NULL;
-}
-
-static void lh7a40xuart_release_port (struct uart_port* port)
-{
-       release_mem_region (port->mapbase, UART_REG_SIZE);
-}
-
-static int lh7a40xuart_request_port (struct uart_port* port)
-{
-       return request_mem_region (port->mapbase, UART_REG_SIZE,
-                                  "serial_lh7a40x") != NULL
-               ? 0 : -EBUSY;
-}
-
-static void lh7a40xuart_config_port (struct uart_port* port, int flags)
-{
-       if (flags & UART_CONFIG_TYPE) {
-               port->type = PORT_LH7A40X;
-               lh7a40xuart_request_port (port);
-       }
-}
-
-static int lh7a40xuart_verify_port (struct uart_port* port,
-                                   struct serial_struct* ser)
-{
-       int ret = 0;
-
-       if (ser->type != PORT_UNKNOWN && ser->type != PORT_LH7A40X)
-               ret = -EINVAL;
-       if (ser->irq < 0 || ser->irq >= nr_irqs)
-               ret = -EINVAL;
-       if (ser->baud_base < 9600) /* *** FIXME: is this true? */
-               ret = -EINVAL;
-       return ret;
-}
-
-static struct uart_ops lh7a40x_uart_ops = {
-       .tx_empty       = lh7a40xuart_tx_empty,
-       .set_mctrl      = lh7a40xuart_set_mctrl,
-       .get_mctrl      = lh7a40xuart_get_mctrl,
-       .stop_tx        = lh7a40xuart_stop_tx,
-       .start_tx       = lh7a40xuart_start_tx,
-       .stop_rx        = lh7a40xuart_stop_rx,
-       .enable_ms      = lh7a40xuart_enable_ms,
-       .break_ctl      = lh7a40xuart_break_ctl,
-       .startup        = lh7a40xuart_startup,
-       .shutdown       = lh7a40xuart_shutdown,
-       .set_termios    = lh7a40xuart_set_termios,
-       .type           = lh7a40xuart_type,
-       .release_port   = lh7a40xuart_release_port,
-       .request_port   = lh7a40xuart_request_port,
-       .config_port    = lh7a40xuart_config_port,
-       .verify_port    = lh7a40xuart_verify_port,
-};
-
-static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = {
-       {
-               .port = {
-                       .membase        = (void*) io_p2v (UART1_PHYS),
-                       .mapbase        = UART1_PHYS,
-                       .iotype         = UPIO_MEM,
-                       .irq            = IRQ_UART1INTR,
-                       .uartclk        = 14745600/2,
-                       .fifosize       = 16,
-                       .ops            = &lh7a40x_uart_ops,
-                       .flags          = UPF_BOOT_AUTOCONF,
-                       .line           = 0,
-               },
-       },
-       {
-               .port = {
-                       .membase        = (void*) io_p2v (UART2_PHYS),
-                       .mapbase        = UART2_PHYS,
-                       .iotype         = UPIO_MEM,
-                       .irq            = IRQ_UART2INTR,
-                       .uartclk        = 14745600/2,
-                       .fifosize       = 16,
-                       .ops            = &lh7a40x_uart_ops,
-                       .flags          = UPF_BOOT_AUTOCONF,
-                       .line           = 1,
-               },
-       },
-       {
-               .port = {
-                       .membase        = (void*) io_p2v (UART3_PHYS),
-                       .mapbase        = UART3_PHYS,
-                       .iotype         = UPIO_MEM,
-                       .irq            = IRQ_UART3INTR,
-                       .uartclk        = 14745600/2,
-                       .fifosize       = 16,
-                       .ops            = &lh7a40x_uart_ops,
-                       .flags          = UPF_BOOT_AUTOCONF,
-                       .line           = 2,
-               },
-       },
-};
-
-#ifndef CONFIG_SERIAL_LH7A40X_CONSOLE
-# define LH7A40X_CONSOLE NULL
-#else
-# define LH7A40X_CONSOLE &lh7a40x_console
-
-static void lh7a40xuart_console_putchar(struct uart_port *port, int ch)
-{
-       while (UR(port, UART_R_STATUS) & nTxRdy)
-               ;
-       UR(port, UART_R_DATA) = ch;
-}
-
-static void lh7a40xuart_console_write (struct console* co,
-                                      const char* s,
-                                      unsigned int count)
-{
-       struct uart_port* port = &lh7a40x_ports[co->index].port;
-       unsigned int con = UR (port, UART_R_CON);
-       unsigned int inten = UR (port, UART_R_INTEN);
-
-
-       UR (port, UART_R_INTEN) = 0;            /* Disable all interrupts */
-       BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); /* Enable UART */
-
-       uart_console_write(port, s, count, lh7a40xuart_console_putchar);
-
-                               /* Wait until all characters are sent */
-       while (UR (port, UART_R_STATUS) & TxBusy)
-               ;
-
-                               /* Restore control and interrupt mask */
-       UR (port, UART_R_CON) = con;
-       UR (port, UART_R_INTEN) = inten;
-}
-
-static void __init lh7a40xuart_console_get_options (struct uart_port* port,
-                                                   int* baud,
-                                                   int* parity,
-                                                   int* bits)
-{
-       if (UR (port, UART_R_CON) & UARTEN) {
-               unsigned int fcon = UR (port, UART_R_FCON);
-               unsigned int quot = UR (port, UART_R_BRCON) + 1;
-
-               switch (fcon & (PEN | EPS)) {
-               default:        *parity = 'n'; break;
-               case PEN:       *parity = 'o'; break;
-               case PEN | EPS: *parity = 'e'; break;
-               }
-
-               switch (fcon & WLEN) {
-               default:
-               case WLEN_8: *bits = 8; break;
-               case WLEN_7: *bits = 7; break;
-               case WLEN_6: *bits = 6; break;
-               case WLEN_5: *bits = 5; break;
-               }
-
-               *baud = port->uartclk/(16*quot);
-       }
-}
-
-static int __init lh7a40xuart_console_setup (struct console* co, char* options)
-{
-       struct uart_port* port;
-       int baud = 38400;
-       int bits = 8;
-       int parity = 'n';
-       int flow = 'n';
-
-       if (co->index >= DEV_NR) /* Bounds check on device number */
-               co->index = 0;
-       port = &lh7a40x_ports[co->index].port;
-
-       if (options)
-               uart_parse_options (options, &baud, &parity, &bits, &flow);
-       else
-               lh7a40xuart_console_get_options (port, &baud, &parity, &bits);
-
-       return uart_set_options (port, co, baud, parity, bits, flow);
-}
-
-static struct uart_driver lh7a40x_reg;
-static struct console lh7a40x_console = {
-       .name           = "ttyAM",
-       .write          = lh7a40xuart_console_write,
-       .device         = uart_console_device,
-       .setup          = lh7a40xuart_console_setup,
-       .flags          = CON_PRINTBUFFER,
-       .index          = -1,
-       .data           = &lh7a40x_reg,
-};
-
-static int __init lh7a40xuart_console_init(void)
-{
-       register_console (&lh7a40x_console);
-       return 0;
-}
-
-console_initcall (lh7a40xuart_console_init);
-
-#endif
-
-static struct uart_driver lh7a40x_reg = {
-       .owner                  = THIS_MODULE,
-       .driver_name            = "ttyAM",
-       .dev_name               = "ttyAM",
-       .major                  = DEV_MAJOR,
-       .minor                  = DEV_MINOR,
-       .nr                     = DEV_NR,
-       .cons                   = LH7A40X_CONSOLE,
-};
-
-static int __init lh7a40xuart_init(void)
-{
-       int ret;
-
-       printk (KERN_INFO "serial: LH7A40X serial driver\n");
-
-       ret = uart_register_driver (&lh7a40x_reg);
-
-       if (ret == 0) {
-               int i;
-
-               for (i = 0; i < DEV_NR; i++) {
-                       /* UART3, when used, requires GPIO pin reallocation */
-                       if (lh7a40x_ports[i].port.mapbase == UART3_PHYS)
-                               GPIO_PINMUX |= 1<<3;
-                       uart_add_one_port (&lh7a40x_reg,
-                                          &lh7a40x_ports[i].port);
-               }
-       }
-       return ret;
-}
-
-static void __exit lh7a40xuart_exit(void)
-{
-       int i;
-
-       for (i = 0; i < DEV_NR; i++)
-               uart_remove_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port);
-
-       uart_unregister_driver (&lh7a40x_reg);
-}
-
-module_init (lh7a40xuart_init);
-module_exit (lh7a40xuart_exit);
-
-MODULE_AUTHOR ("Marc Singer");
-MODULE_DESCRIPTION ("Sharp LH7A40X serial port driver");
-MODULE_LICENSE ("GPL");
index fceea5e4e02f2f7d21ad43f6193390648c4fb56f..41b6e51188e44e4ac66590231c4a884b96a8b8f3 100644 (file)
@@ -31,7 +31,6 @@ config USB_ARCH_HAS_OHCI
        # ARM:
        default y if SA1111
        default y if ARCH_OMAP
-       default y if ARCH_LH7A404
        default y if ARCH_S3C2410
        default y if PXA27x
        default y if PXA3xx
index 1dc9739277b4941498619b88a98e6731e93fdcaf..08a48ae23745fcde9623621ab59d48a74da1c51a 100644 (file)
@@ -176,18 +176,6 @@ config USB_FSL_USB2
        default USB_GADGET
        select USB_GADGET_SELECTED
 
-config USB_GADGET_LH7A40X
-       boolean "LH7A40X"
-       depends on ARCH_LH7A40X
-       help
-          This driver provides USB Device Controller driver for LH7A40x
-
-config USB_LH7A40X
-       tristate
-       depends on USB_GADGET_LH7A40X
-       default USB_GADGET
-       select USB_GADGET_SELECTED
-
 config USB_GADGET_OMAP
        boolean "OMAP USB Device Controller"
        depends on ARCH_OMAP
index 55f5e8ae5924f5962cc6e2d6a2939723afec29fa..a2f7f9a4f4a8c772765e50eb4ab599f3b73f3507 100644 (file)
@@ -11,7 +11,6 @@ obj-$(CONFIG_USB_PXA27X)      += pxa27x_udc.o
 obj-$(CONFIG_USB_IMX)          += imx_udc.o
 obj-$(CONFIG_USB_GOKU)         += goku_udc.o
 obj-$(CONFIG_USB_OMAP)         += omap_udc.o
-obj-$(CONFIG_USB_LH7A40X)      += lh7a40x_udc.o
 obj-$(CONFIG_USB_S3C2410)      += s3c2410_udc.o
 obj-$(CONFIG_USB_AT91)         += at91_udc.o
 obj-$(CONFIG_USB_ATMEL_USBA)   += atmel_usba_udc.o
index 5c2720d64ffa4589bceeb971425f07c1fffc5e3e..e896f6359dfecd17c57660cd98fd646fbd19d4ba 100644 (file)
 #define        gadget_is_goku(g)       0
 #endif
 
-#ifdef CONFIG_USB_GADGET_LH7A40X
-#define        gadget_is_lh7a40x(g)    !strcmp("lh7a40x_udc", (g)->name)
-#else
-#define        gadget_is_lh7a40x(g)    0
-#endif
-
 #ifdef CONFIG_USB_GADGET_OMAP
 #define        gadget_is_omap(g)       !strcmp("omap_udc", (g)->name)
 #else
@@ -181,8 +175,6 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget)
                return 0x06;
        else if (gadget_is_omap(gadget))
                return 0x08;
-       else if (gadget_is_lh7a40x(gadget))
-               return 0x09;
        else if (gadget_is_pxa27x(gadget))
                return 0x11;
        else if (gadget_is_s3c2410(gadget))
diff --git a/drivers/usb/gadget/lh7a40x_udc.c b/drivers/usb/gadget/lh7a40x_udc.c
deleted file mode 100644 (file)
index 6b58bd8..0000000
+++ /dev/null
@@ -1,2152 +0,0 @@
-/*
- * linux/drivers/usb/gadget/lh7a40x_udc.c
- * Sharp LH7A40x on-chip full speed USB device controllers
- *
- * Copyright (C) 2004 Mikko Lahteenmaki, Nordic ID
- * Copyright (C) 2004 Bo Henriksen, Nordic ID
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-
-#include "lh7a40x_udc.h"
-
-//#define DEBUG printk
-//#define DEBUG_EP0 printk
-//#define DEBUG_SETUP printk
-
-#ifndef DEBUG_EP0
-# define DEBUG_EP0(fmt,args...)
-#endif
-#ifndef DEBUG_SETUP
-# define DEBUG_SETUP(fmt,args...)
-#endif
-#ifndef DEBUG
-# define NO_STATES
-# define DEBUG(fmt,args...)
-#endif
-
-#define        DRIVER_DESC                     "LH7A40x USB Device Controller"
-#define        DRIVER_VERSION          __DATE__
-
-#ifndef _BIT                   /* FIXME - what happended to _BIT in 2.6.7bk18? */
-#define _BIT(x) (1<<(x))
-#endif
-
-struct lh7a40x_udc *the_controller;
-
-static const char driver_name[] = "lh7a40x_udc";
-static const char driver_desc[] = DRIVER_DESC;
-static const char ep0name[] = "ep0-control";
-
-/*
-  Local definintions.
-*/
-
-#ifndef NO_STATES
-static char *state_names[] = {
-       "WAIT_FOR_SETUP",
-       "DATA_STATE_XMIT",
-       "DATA_STATE_NEED_ZLP",
-       "WAIT_FOR_OUT_STATUS",
-       "DATA_STATE_RECV"
-};
-#endif
-
-/*
-  Local declarations.
-*/
-static int lh7a40x_ep_enable(struct usb_ep *ep,
-                            const struct usb_endpoint_descriptor *);
-static int lh7a40x_ep_disable(struct usb_ep *ep);
-static struct usb_request *lh7a40x_alloc_request(struct usb_ep *ep, gfp_t);
-static void lh7a40x_free_request(struct usb_ep *ep, struct usb_request *);
-static int lh7a40x_queue(struct usb_ep *ep, struct usb_request *, gfp_t);
-static int lh7a40x_dequeue(struct usb_ep *ep, struct usb_request *);
-static int lh7a40x_set_halt(struct usb_ep *ep, int);
-static int lh7a40x_fifo_status(struct usb_ep *ep);
-static void lh7a40x_fifo_flush(struct usb_ep *ep);
-static void lh7a40x_ep0_kick(struct lh7a40x_udc *dev, struct lh7a40x_ep *ep);
-static void lh7a40x_handle_ep0(struct lh7a40x_udc *dev, u32 intr);
-
-static void done(struct lh7a40x_ep *ep, struct lh7a40x_request *req,
-                int status);
-static void pio_irq_enable(int bEndpointAddress);
-static void pio_irq_disable(int bEndpointAddress);
-static void stop_activity(struct lh7a40x_udc *dev,
-                         struct usb_gadget_driver *driver);
-static void flush(struct lh7a40x_ep *ep);
-static void udc_enable(struct lh7a40x_udc *dev);
-static void udc_set_address(struct lh7a40x_udc *dev, unsigned char address);
-
-static struct usb_ep_ops lh7a40x_ep_ops = {
-       .enable = lh7a40x_ep_enable,
-       .disable = lh7a40x_ep_disable,
-
-       .alloc_request = lh7a40x_alloc_request,
-       .free_request = lh7a40x_free_request,
-
-       .queue = lh7a40x_queue,
-       .dequeue = lh7a40x_dequeue,
-
-       .set_halt = lh7a40x_set_halt,
-       .fifo_status = lh7a40x_fifo_status,
-       .fifo_flush = lh7a40x_fifo_flush,
-};
-
-/* Inline code */
-
-static __inline__ int write_packet(struct lh7a40x_ep *ep,
-                                  struct lh7a40x_request *req, int max)
-{
-       u8 *buf;
-       int length, count;
-       volatile u32 *fifo = (volatile u32 *)ep->fifo;
-
-       buf = req->req.buf + req->req.actual;
-       prefetch(buf);
-
-       length = req->req.length - req->req.actual;
-       length = min(length, max);
-       req->req.actual += length;
-
-       DEBUG("Write %d (max %d), fifo %p\n", length, max, fifo);
-
-       count = length;
-       while (count--) {
-               *fifo = *buf++;
-       }
-
-       return length;
-}
-
-static __inline__ void usb_set_index(u32 ep)
-{
-       *(volatile u32 *)io_p2v(USB_INDEX) = ep;
-}
-
-static __inline__ u32 usb_read(u32 port)
-{
-       return *(volatile u32 *)io_p2v(port);
-}
-
-static __inline__ void usb_write(u32 val, u32 port)
-{
-       *(volatile u32 *)io_p2v(port) = val;
-}
-
-static __inline__ void usb_set(u32 val, u32 port)
-{
-       volatile u32 *ioport = (volatile u32 *)io_p2v(port);
-       u32 after = (*ioport) | val;
-       *ioport = after;
-}
-
-static __inline__ void usb_clear(u32 val, u32 port)
-{
-       volatile u32 *ioport = (volatile u32 *)io_p2v(port);
-       u32 after = (*ioport) & ~val;
-       *ioport = after;
-}
-
-/*-------------------------------------------------------------------------*/
-
-#define GPIO_PORTC_DR  (0x80000E08)
-#define GPIO_PORTC_DDR         (0x80000E18)
-#define GPIO_PORTC_PDR         (0x80000E70)
-
-/* get port C pin data register */
-#define get_portc_pdr(bit)             ((usb_read(GPIO_PORTC_PDR) & _BIT(bit)) != 0)
-/* get port C data direction register */
-#define get_portc_ddr(bit)             ((usb_read(GPIO_PORTC_DDR) & _BIT(bit)) != 0)
-/* set port C data register */
-#define set_portc_dr(bit, val)         (val ? usb_set(_BIT(bit), GPIO_PORTC_DR) : usb_clear(_BIT(bit), GPIO_PORTC_DR))
-/* set port C data direction register */
-#define set_portc_ddr(bit, val) (val ? usb_set(_BIT(bit), GPIO_PORTC_DDR) : usb_clear(_BIT(bit), GPIO_PORTC_DDR))
-
-/*
- * LPD7A404 GPIO's:
- * Port C bit 1 = USB Port 1 Power Enable
- * Port C bit 2 = USB Port 1 Data Carrier Detect
- */
-#define is_usb_connected()             get_portc_pdr(2)
-
-#ifdef CONFIG_USB_GADGET_DEBUG_FILES
-
-static const char proc_node_name[] = "driver/udc";
-
-static int
-udc_proc_read(char *page, char **start, off_t off, int count,
-             int *eof, void *_dev)
-{
-       char *buf = page;
-       struct lh7a40x_udc *dev = _dev;
-       char *next = buf;
-       unsigned size = count;
-       unsigned long flags;
-       int t;
-
-       if (off != 0)
-               return 0;
-
-       local_irq_save(flags);
-
-       /* basic device status */
-       t = scnprintf(next, size,
-                     DRIVER_DESC "\n"
-                     "%s version: %s\n"
-                     "Gadget driver: %s\n"
-                     "Host: %s\n\n",
-                     driver_name, DRIVER_VERSION,
-                     dev->driver ? dev->driver->driver.name : "(none)",
-                     is_usb_connected()? "full speed" : "disconnected");
-       size -= t;
-       next += t;
-
-       t = scnprintf(next, size,
-                     "GPIO:\n"
-                     " Port C bit 1: %d, dir %d\n"
-                     " Port C bit 2: %d, dir %d\n\n",
-                     get_portc_pdr(1), get_portc_ddr(1),
-                     get_portc_pdr(2), get_portc_ddr(2)
-           );
-       size -= t;
-       next += t;
-
-       t = scnprintf(next, size,
-                     "DCP pullup: %d\n\n",
-                     (usb_read(USB_PM) & PM_USB_DCP) != 0);
-       size -= t;
-       next += t;
-
-       local_irq_restore(flags);
-       *eof = 1;
-       return count - size;
-}
-
-#define create_proc_files()    create_proc_read_entry(proc_node_name, 0, NULL, udc_proc_read, dev)
-#define remove_proc_files()    remove_proc_entry(proc_node_name, NULL)
-
-#else  /* !CONFIG_USB_GADGET_DEBUG_FILES */
-
-#define create_proc_files() do {} while (0)
-#define remove_proc_files() do {} while (0)
-
-#endif /* CONFIG_USB_GADGET_DEBUG_FILES */
-
-/*
- *     udc_disable - disable USB device controller
- */
-static void udc_disable(struct lh7a40x_udc *dev)
-{
-       DEBUG("%s, %p\n", __func__, dev);
-
-       udc_set_address(dev, 0);
-
-       /* Disable interrupts */
-       usb_write(0, USB_IN_INT_EN);
-       usb_write(0, USB_OUT_INT_EN);
-       usb_write(0, USB_INT_EN);
-
-       /* Disable the USB */
-       usb_write(0, USB_PM);
-
-#ifdef CONFIG_ARCH_LH7A404
-       /* Disable USB power */
-       set_portc_dr(1, 0);
-#endif
-
-       /* if hardware supports it, disconnect from usb */
-       /* make_usb_disappear(); */
-
-       dev->ep0state = WAIT_FOR_SETUP;
-       dev->gadget.speed = USB_SPEED_UNKNOWN;
-       dev->usb_address = 0;
-}
-
-/*
- *     udc_reinit - initialize software state
- */
-static void udc_reinit(struct lh7a40x_udc *dev)
-{
-       u32 i;
-
-       DEBUG("%s, %p\n", __func__, dev);
-
-       /* device/ep0 records init */
-       INIT_LIST_HEAD(&dev->gadget.ep_list);
-       INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
-       dev->ep0state = WAIT_FOR_SETUP;
-
-       /* basic endpoint records init */
-       for (i = 0; i < UDC_MAX_ENDPOINTS; i++) {
-               struct lh7a40x_ep *ep = &dev->ep[i];
-
-               if (i != 0)
-                       list_add_tail(&ep->ep.ep_list, &dev->gadget.ep_list);
-
-               ep->desc = 0;
-               ep->stopped = 0;
-               INIT_LIST_HEAD(&ep->queue);
-               ep->pio_irqs = 0;
-       }
-
-       /* the rest was statically initialized, and is read-only */
-}
-
-#define BYTES2MAXP(x)  (x / 8)
-#define MAXP2BYTES(x)  (x * 8)
-
-/* until it's enabled, this UDC should be completely invisible
- * to any USB host.
- */
-static void udc_enable(struct lh7a40x_udc *dev)
-{
-       int ep;
-
-       DEBUG("%s, %p\n", __func__, dev);
-
-       dev->gadget.speed = USB_SPEED_UNKNOWN;
-
-#ifdef CONFIG_ARCH_LH7A404
-       /* Set Port C bit 1 & 2 as output */
-       set_portc_ddr(1, 1);
-       set_portc_ddr(2, 1);
-
-       /* Enable USB power */
-       set_portc_dr(1, 0);
-#endif
-
-       /*
-        * C.f Chapter 18.1.3.1 Initializing the USB
-        */
-
-       /* Disable the USB */
-       usb_clear(PM_USB_ENABLE, USB_PM);
-
-       /* Reset APB & I/O sides of the USB */
-       usb_set(USB_RESET_APB | USB_RESET_IO, USB_RESET);
-       mdelay(5);
-       usb_clear(USB_RESET_APB | USB_RESET_IO, USB_RESET);
-
-       /* Set MAXP values for each */
-       for (ep = 0; ep < UDC_MAX_ENDPOINTS; ep++) {
-               struct lh7a40x_ep *ep_reg = &dev->ep[ep];
-               u32 csr;
-
-               usb_set_index(ep);
-
-               switch (ep_reg->ep_type) {
-               case ep_bulk_in:
-               case ep_interrupt:
-                       usb_clear(USB_IN_CSR2_USB_DMA_EN | USB_IN_CSR2_AUTO_SET,
-                                 ep_reg->csr2);
-                       /* Fall through */
-               case ep_control:
-                       usb_write(BYTES2MAXP(ep_maxpacket(ep_reg)),
-                                 USB_IN_MAXP);
-                       break;
-               case ep_bulk_out:
-                       usb_clear(USB_OUT_CSR2_USB_DMA_EN |
-                                 USB_OUT_CSR2_AUTO_CLR, ep_reg->csr2);
-                       usb_write(BYTES2MAXP(ep_maxpacket(ep_reg)),
-                                 USB_OUT_MAXP);
-                       break;
-               }
-
-               /* Read & Write CSR1, just in case */
-               csr = usb_read(ep_reg->csr1);
-               usb_write(csr, ep_reg->csr1);
-
-               flush(ep_reg);
-       }
-
-       /* Disable interrupts */
-       usb_write(0, USB_IN_INT_EN);
-       usb_write(0, USB_OUT_INT_EN);
-       usb_write(0, USB_INT_EN);
-
-       /* Enable interrupts */
-       usb_set(USB_IN_INT_EP0, USB_IN_INT_EN);
-       usb_set(USB_INT_RESET_INT | USB_INT_RESUME_INT, USB_INT_EN);
-       /* Dont enable rest of the interrupts */
-       /* usb_set(USB_IN_INT_EP3 | USB_IN_INT_EP1 | USB_IN_INT_EP0, USB_IN_INT_EN);
-          usb_set(USB_OUT_INT_EP2, USB_OUT_INT_EN); */
-
-       /* Enable SUSPEND */
-       usb_set(PM_ENABLE_SUSPEND, USB_PM);
-
-       /* Enable the USB */
-       usb_set(PM_USB_ENABLE, USB_PM);
-
-#ifdef CONFIG_ARCH_LH7A404
-       /* NOTE: DOES NOT WORK! */
-       /* Let host detect UDC:
-        * Software must write a 0 to the PMR:DCP_CTRL bit to turn this
-        * transistor on and pull the USBDP pin HIGH.
-        */
-       /* usb_clear(PM_USB_DCP, USB_PM);
-          usb_set(PM_USB_DCP, USB_PM); */
-#endif
-}
-
-/*
-  Register entry point for the peripheral controller driver.
-*/
-int usb_gadget_probe_driver(struct usb_gadget_driver *driver,
-               int (*bind)(struct usb_gadget *))
-{
-       struct lh7a40x_udc *dev = the_controller;
-       int retval;
-
-       DEBUG("%s: %s\n", __func__, driver->driver.name);
-
-       if (!driver
-                       || driver->speed != USB_SPEED_FULL
-                       || !bind
-                       || !driver->disconnect
-                       || !driver->setup)
-               return -EINVAL;
-       if (!dev)
-               return -ENODEV;
-       if (dev->driver)
-               return -EBUSY;
-
-       /* first hook up the driver ... */
-       dev->driver = driver;
-       dev->gadget.dev.driver = &driver->driver;
-
-       device_add(&dev->gadget.dev);
-       retval = bind(&dev->gadget);
-       if (retval) {
-               printk(KERN_WARNING "%s: bind to driver %s --> error %d\n",
-                      dev->gadget.name, driver->driver.name, retval);
-               device_del(&dev->gadget.dev);
-
-               dev->driver = 0;
-               dev->gadget.dev.driver = 0;
-               return retval;
-       }
-
-       /* ... then enable host detection and ep0; and we're ready
-        * for set_configuration as well as eventual disconnect.
-        * NOTE:  this shouldn't power up until later.
-        */
-       printk(KERN_WARNING "%s: registered gadget driver '%s'\n",
-              dev->gadget.name, driver->driver.name);
-
-       udc_enable(dev);
-
-       return 0;
-}
-EXPORT_SYMBOL(usb_gadget_probe_driver);
-
-/*
-  Unregister entry point for the peripheral controller driver.
-*/
-int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
-{
-       struct lh7a40x_udc *dev = the_controller;
-       unsigned long flags;
-
-       if (!dev)
-               return -ENODEV;
-       if (!driver || driver != dev->driver || !driver->unbind)
-               return -EINVAL;
-
-       spin_lock_irqsave(&dev->lock, flags);
-       dev->driver = 0;
-       stop_activity(dev, driver);
-       spin_unlock_irqrestore(&dev->lock, flags);
-
-       driver->unbind(&dev->gadget);
-       dev->gadget.dev.driver = NULL;
-       device_del(&dev->gadget.dev);
-
-       udc_disable(dev);
-
-       DEBUG("unregistered gadget driver '%s'\n", driver->driver.name);
-       return 0;
-}
-
-EXPORT_SYMBOL(usb_gadget_unregister_driver);
-
-/*-------------------------------------------------------------------------*/
-
-/** Write request to FIFO (max write == maxp size)
- *  Return:  0 = still running, 1 = completed, negative = errno
- *  NOTE: INDEX register must be set for EP
- */
-static int write_fifo(struct lh7a40x_ep *ep, struct lh7a40x_request *req)
-{
-       u32 max;
-       u32 csr;
-
-       max = le16_to_cpu(ep->desc->wMaxPacketSize);
-
-       csr = usb_read(ep->csr1);
-       DEBUG("CSR: %x %d\n", csr, csr & USB_IN_CSR1_FIFO_NOT_EMPTY);
-
-       if (!(csr & USB_IN_CSR1_FIFO_NOT_EMPTY)) {
-               unsigned count;
-               int is_last, is_short;
-
-               count = write_packet(ep, req, max);
-               usb_set(USB_IN_CSR1_IN_PKT_RDY, ep->csr1);
-
-               /* last packet is usually short (or a zlp) */
-               if (unlikely(count != max))
-                       is_last = is_short = 1;
-               else {
-                       if (likely(req->req.length != req->req.actual)
-                           || req->req.zero)
-                               is_last = 0;
-                       else
-                               is_last = 1;
-                       /* interrupt/iso maxpacket may not fill the fifo */
-                       is_short = unlikely(max < ep_maxpacket(ep));
-               }
-
-               DEBUG("%s: wrote %s %d bytes%s%s %d left %p\n", __func__,
-                     ep->ep.name, count,
-                     is_last ? "/L" : "", is_short ? "/S" : "",
-                     req->req.length - req->req.actual, req);
-
-               /* requests complete when all IN data is in the FIFO */
-               if (is_last) {
-                       done(ep, req, 0);
-                       if (list_empty(&ep->queue)) {
-                               pio_irq_disable(ep_index(ep));
-                       }
-                       return 1;
-               }
-       } else {
-               DEBUG("Hmm.. %d ep FIFO is not empty!\n", ep_index(ep));
-       }
-
-       return 0;
-}
-
-/** Read to request from FIFO (max read == bytes in fifo)
- *  Return:  0 = still running, 1 = completed, negative = errno
- *  NOTE: INDEX register must be set for EP
- */
-static int read_fifo(struct lh7a40x_ep *ep, struct lh7a40x_request *req)
-{
-       u32 csr;
-       u8 *buf;
-       unsigned bufferspace, count, is_short;
-       volatile u32 *fifo = (volatile u32 *)ep->fifo;
-
-       /* make sure there's a packet in the FIFO. */
-       csr = usb_read(ep->csr1);
-       if (!(csr & USB_OUT_CSR1_OUT_PKT_RDY)) {
-               DEBUG("%s: Packet NOT ready!\n", __func__);
-               return -EINVAL;
-       }
-
-       buf = req->req.buf + req->req.actual;
-       prefetchw(buf);
-       bufferspace = req->req.length - req->req.actual;
-
-       /* read all bytes from this packet */
-       count = usb_read(USB_OUT_FIFO_WC1);
-       req->req.actual += min(count, bufferspace);
-
-       is_short = (count < ep->ep.maxpacket);
-       DEBUG("read %s %02x, %d bytes%s req %p %d/%d\n",
-             ep->ep.name, csr, count,
-             is_short ? "/S" : "", req, req->req.actual, req->req.length);
-
-       while (likely(count-- != 0)) {
-               u8 byte = (u8) (*fifo & 0xff);
-
-               if (unlikely(bufferspace == 0)) {
-                       /* this happens when the driver's buffer
-                        * is smaller than what the host sent.
-                        * discard the extra data.
-                        */
-                       if (req->req.status != -EOVERFLOW)
-                               printk(KERN_WARNING "%s overflow %d\n",
-                                      ep->ep.name, count);
-                       req->req.status = -EOVERFLOW;
-               } else {
-                       *buf++ = byte;
-                       bufferspace--;
-               }
-       }
-
-       usb_clear(USB_OUT_CSR1_OUT_PKT_RDY, ep->csr1);
-
-       /* completion */
-       if (is_short || req->req.actual == req->req.length) {
-               done(ep, req, 0);
-               usb_set(USB_OUT_CSR1_FIFO_FLUSH, ep->csr1);
-
-               if (list_empty(&ep->queue))
-                       pio_irq_disable(ep_index(ep));
-               return 1;
-       }
-
-       /* finished that packet.  the next one may be waiting... */
-       return 0;
-}
-
-/*
- *     done - retire a request; caller blocked irqs
- *  INDEX register is preserved to keep same
- */
-static void done(struct lh7a40x_ep *ep, struct lh7a40x_request *req, int status)
-{
-       unsigned int stopped = ep->stopped;
-       u32 index;
-
-       DEBUG("%s, %p\n", __func__, ep);
-       list_del_init(&req->queue);
-
-       if (likely(req->req.status == -EINPROGRESS))
-               req->req.status = status;
-       else
-               status = req->req.status;
-
-       if (status && status != -ESHUTDOWN)
-               DEBUG("complete %s req %p stat %d len %u/%u\n",
-                     ep->ep.name, &req->req, status,
-                     req->req.actual, req->req.length);
-
-       /* don't modify queue heads during completion callback */
-       ep->stopped = 1;
-       /* Read current index (completion may modify it) */
-       index = usb_read(USB_INDEX);
-
-       spin_unlock(&ep->dev->lock);
-       req->req.complete(&ep->ep, &req->req);
-       spin_lock(&ep->dev->lock);
-
-       /* Restore index */
-       usb_set_index(index);
-       ep->stopped = stopped;
-}
-
-/** Enable EP interrupt */
-static void pio_irq_enable(int ep)
-{
-       DEBUG("%s: %d\n", __func__, ep);
-
-       switch (ep) {
-       case 1:
-               usb_set(USB_IN_INT_EP1, USB_IN_INT_EN);
-               break;
-       case 2:
-               usb_set(USB_OUT_INT_EP2, USB_OUT_INT_EN);
-               break;
-       case 3:
-               usb_set(USB_IN_INT_EP3, USB_IN_INT_EN);
-               break;
-       default:
-               DEBUG("Unknown endpoint: %d\n", ep);
-               break;
-       }
-}
-
-/** Disable EP interrupt */
-static void pio_irq_disable(int ep)
-{
-       DEBUG("%s: %d\n", __func__, ep);
-
-       switch (ep) {
-       case 1:
-               usb_clear(USB_IN_INT_EP1, USB_IN_INT_EN);
-               break;
-       case 2:
-               usb_clear(USB_OUT_INT_EP2, USB_OUT_INT_EN);
-               break;
-       case 3:
-               usb_clear(USB_IN_INT_EP3, USB_IN_INT_EN);
-               break;
-       default:
-               DEBUG("Unknown endpoint: %d\n", ep);
-               break;
-       }
-}
-
-/*
- *     nuke - dequeue ALL requests
- */
-void nuke(struct lh7a40x_ep *ep, int status)
-{
-       struct lh7a40x_request *req;
-
-       DEBUG("%s, %p\n", __func__, ep);
-
-       /* Flush FIFO */
-       flush(ep);
-
-       /* called with irqs blocked */
-       while (!list_empty(&ep->queue)) {
-               req = list_entry(ep->queue.next, struct lh7a40x_request, queue);
-               done(ep, req, status);
-       }
-
-       /* Disable IRQ if EP is enabled (has descriptor) */
-       if (ep->desc)
-               pio_irq_disable(ep_index(ep));
-}
-
-/*
-void nuke_all(struct lh7a40x_udc *dev)
-{
-       int n;
-       for(n=0; n<UDC_MAX_ENDPOINTS; n++) {
-               struct lh7a40x_ep *ep = &dev->ep[n];
-               usb_set_index(n);
-               nuke(ep, 0);
-       }
-}*/
-
-/*
-static void flush_all(struct lh7a40x_udc *dev)
-{
-       int n;
-    for (n = 0; n < UDC_MAX_ENDPOINTS; n++)
-    {
-               struct lh7a40x_ep *ep = &dev->ep[n];
-               flush(ep);
-    }
-}
-*/
-
-/** Flush EP
- * NOTE: INDEX register must be set before this call
- */
-static void flush(struct lh7a40x_ep *ep)
-{
-       DEBUG("%s, %p\n", __func__, ep);
-
-       switch (ep->ep_type) {
-       case ep_control:
-               /* check, by implication c.f. 15.1.2.11 */
-               break;
-
-       case ep_bulk_in:
-       case ep_interrupt:
-               /* if(csr & USB_IN_CSR1_IN_PKT_RDY) */
-               usb_set(USB_IN_CSR1_FIFO_FLUSH, ep->csr1);
-               break;
-
-       case ep_bulk_out:
-               /* if(csr & USB_OUT_CSR1_OUT_PKT_RDY) */
-               usb_set(USB_OUT_CSR1_FIFO_FLUSH, ep->csr1);
-               break;
-       }
-}
-
-/**
- * lh7a40x_in_epn - handle IN interrupt
- */
-static void lh7a40x_in_epn(struct lh7a40x_udc *dev, u32 ep_idx, u32 intr)
-{
-       u32 csr;
-       struct lh7a40x_ep *ep = &dev->ep[ep_idx];
-       struct lh7a40x_request *req;
-
-       usb_set_index(ep_idx);
-
-       csr = usb_read(ep->csr1);
-       DEBUG("%s: %d, csr %x\n", __func__, ep_idx, csr);
-
-       if (csr & USB_IN_CSR1_SENT_STALL) {
-               DEBUG("USB_IN_CSR1_SENT_STALL\n");
-               usb_set(USB_IN_CSR1_SENT_STALL /*|USB_IN_CSR1_SEND_STALL */ ,
-                       ep->csr1);
-               return;
-       }
-
-       if (!ep->desc) {
-               DEBUG("%s: NO EP DESC\n", __func__);
-               return;
-       }
-
-       if (list_empty(&ep->queue))
-               req = 0;
-       else
-               req = list_entry(ep->queue.next, struct lh7a40x_request, queue);
-
-       DEBUG("req: %p\n", req);
-
-       if (!req)
-               return;
-
-       write_fifo(ep, req);
-}
-
-/* ********************************************************************************************* */
-/* Bulk OUT (recv)
- */
-
-static void lh7a40x_out_epn(struct lh7a40x_udc *dev, u32 ep_idx, u32 intr)
-{
-       struct lh7a40x_ep *ep = &dev->ep[ep_idx];
-       struct lh7a40x_request *req;
-
-       DEBUG("%s: %d\n", __func__, ep_idx);
-
-       usb_set_index(ep_idx);
-
-       if (ep->desc) {
-               u32 csr;
-               csr = usb_read(ep->csr1);
-
-               while ((csr =
-                       usb_read(ep->
-                                csr1)) & (USB_OUT_CSR1_OUT_PKT_RDY |
-                                          USB_OUT_CSR1_SENT_STALL)) {
-                       DEBUG("%s: %x\n", __func__, csr);
-
-                       if (csr & USB_OUT_CSR1_SENT_STALL) {
-                               DEBUG("%s: stall sent, flush fifo\n",
-                                     __func__);
-                               /* usb_set(USB_OUT_CSR1_FIFO_FLUSH, ep->csr1); */
-                               flush(ep);
-                       } else if (csr & USB_OUT_CSR1_OUT_PKT_RDY) {
-                               if (list_empty(&ep->queue))
-                                       req = 0;
-                               else
-                                       req =
-                                           list_entry(ep->queue.next,
-                                                      struct lh7a40x_request,
-                                                      queue);
-
-                               if (!req) {
-                                       printk(KERN_WARNING
-                                              "%s: NULL REQ %d\n",
-                                              __func__, ep_idx);
-                                       flush(ep);
-                                       break;
-                               } else {
-                                       read_fifo(ep, req);
-                               }
-                       }
-
-               }
-
-       } else {
-               /* Throw packet away.. */
-               printk(KERN_WARNING "%s: No descriptor?!?\n", __func__);
-               flush(ep);
-       }
-}
-
-static void stop_activity(struct lh7a40x_udc *dev,
-                         struct usb_gadget_driver *driver)
-{
-       int i;
-
-       /* don't disconnect drivers more than once */
-       if (dev->gadget.speed == USB_SPEED_UNKNOWN)
-               driver = 0;
-       dev->gadget.speed = USB_SPEED_UNKNOWN;
-
-       /* prevent new request submissions, kill any outstanding requests  */
-       for (i = 0; i < UDC_MAX_ENDPOINTS; i++) {
-               struct lh7a40x_ep *ep = &dev->ep[i];
-               ep->stopped = 1;
-
-               usb_set_index(i);
-               nuke(ep, -ESHUTDOWN);
-       }
-
-       /* report disconnect; the driver is already quiesced */
-       if (driver) {
-               spin_unlock(&dev->lock);
-               driver->disconnect(&dev->gadget);
-               spin_lock(&dev->lock);
-       }
-
-       /* re-init driver-visible data structures */
-       udc_reinit(dev);
-}
-
-/** Handle USB RESET interrupt
- */
-static void lh7a40x_reset_intr(struct lh7a40x_udc *dev)
-{
-#if 0                          /* def CONFIG_ARCH_LH7A404 */
-       /* Does not work always... */
-
-       DEBUG("%s: %d\n", __func__, dev->usb_address);
-
-       if (!dev->usb_address) {
-               /*usb_set(USB_RESET_IO, USB_RESET);
-                  mdelay(5);
-                  usb_clear(USB_RESET_IO, USB_RESET); */
-               return;
-       }
-       /* Put the USB controller into reset. */
-       usb_set(USB_RESET_IO, USB_RESET);
-
-       /* Set Device ID to 0 */
-       udc_set_address(dev, 0);
-
-       /* Let PLL2 settle down */
-       mdelay(5);
-
-       /* Release the USB controller from reset */
-       usb_clear(USB_RESET_IO, USB_RESET);
-
-       /* Re-enable UDC */
-       udc_enable(dev);
-
-#endif
-       dev->gadget.speed = USB_SPEED_FULL;
-}
-
-/*
- *     lh7a40x usb client interrupt handler.
- */
-static irqreturn_t lh7a40x_udc_irq(int irq, void *_dev)
-{
-       struct lh7a40x_udc *dev = _dev;
-
-       DEBUG("\n\n");
-
-       spin_lock(&dev->lock);
-
-       for (;;) {
-               u32 intr_in = usb_read(USB_IN_INT);
-               u32 intr_out = usb_read(USB_OUT_INT);
-               u32 intr_int = usb_read(USB_INT);
-
-               /* Test also against enable bits.. (lh7a40x errata).. Sigh.. */
-               u32 in_en = usb_read(USB_IN_INT_EN);
-               u32 out_en = usb_read(USB_OUT_INT_EN);
-
-               if (!intr_out && !intr_in && !intr_int)
-                       break;
-
-               DEBUG("%s (on state %s)\n", __func__,
-                     state_names[dev->ep0state]);
-               DEBUG("intr_out = %x\n", intr_out);
-               DEBUG("intr_in  = %x\n", intr_in);
-               DEBUG("intr_int = %x\n", intr_int);
-
-               if (intr_in) {
-                       usb_write(intr_in, USB_IN_INT);
-
-                       if ((intr_in & USB_IN_INT_EP1)
-                           && (in_en & USB_IN_INT_EP1)) {
-                               DEBUG("USB_IN_INT_EP1\n");
-                               lh7a40x_in_epn(dev, 1, intr_in);
-                       }
-                       if ((intr_in & USB_IN_INT_EP3)
-                           && (in_en & USB_IN_INT_EP3)) {
-                               DEBUG("USB_IN_INT_EP3\n");
-                               lh7a40x_in_epn(dev, 3, intr_in);
-                       }
-                       if (intr_in & USB_IN_INT_EP0) {
-                               DEBUG("USB_IN_INT_EP0 (control)\n");
-                               lh7a40x_handle_ep0(dev, intr_in);
-                       }
-               }
-
-               if (intr_out) {
-                       usb_write(intr_out, USB_OUT_INT);
-
-                       if ((intr_out & USB_OUT_INT_EP2)
-                           && (out_en & USB_OUT_INT_EP2)) {
-                               DEBUG("USB_OUT_INT_EP2\n");
-                               lh7a40x_out_epn(dev, 2, intr_out);
-                       }
-               }
-
-               if (intr_int) {
-                       usb_write(intr_int, USB_INT);
-
-                       if (intr_int & USB_INT_RESET_INT) {
-                               lh7a40x_reset_intr(dev);
-                       }
-
-                       if (intr_int & USB_INT_RESUME_INT) {
-                               DEBUG("USB resume\n");
-
-                               if (dev->gadget.speed != USB_SPEED_UNKNOWN
-                                   && dev->driver
-                                   && dev->driver->resume
-                                   && is_usb_connected()) {
-                                       dev->driver->resume(&dev->gadget);
-                               }
-                       }
-
-                       if (intr_int & USB_INT_SUSPEND_INT) {
-                               DEBUG("USB suspend%s\n",
-                                     is_usb_connected()? "" : "+disconnect");
-                               if (!is_usb_connected()) {
-                                       stop_activity(dev, dev->driver);
-                               } else if (dev->gadget.speed !=
-                                          USB_SPEED_UNKNOWN && dev->driver
-                                          && dev->driver->suspend) {
-                                       dev->driver->suspend(&dev->gadget);
-                               }
-                       }
-
-               }
-       }
-
-       spin_unlock(&dev->lock);
-
-       return IRQ_HANDLED;
-}
-
-static int lh7a40x_ep_enable(struct usb_ep *_ep,
-                            const struct usb_endpoint_descriptor *desc)
-{
-       struct lh7a40x_ep *ep;
-       struct lh7a40x_udc *dev;
-       unsigned long flags;
-
-       DEBUG("%s, %p\n", __func__, _ep);
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (!_ep || !desc || ep->desc || _ep->name == ep0name
-           || desc->bDescriptorType != USB_DT_ENDPOINT
-           || ep->bEndpointAddress != desc->bEndpointAddress
-           || ep_maxpacket(ep) < le16_to_cpu(desc->wMaxPacketSize)) {
-               DEBUG("%s, bad ep or descriptor\n", __func__);
-               return -EINVAL;
-       }
-
-       /* xfer types must match, except that interrupt ~= bulk */
-       if (ep->bmAttributes != desc->bmAttributes
-           && ep->bmAttributes != USB_ENDPOINT_XFER_BULK
-           && desc->bmAttributes != USB_ENDPOINT_XFER_INT) {
-               DEBUG("%s, %s type mismatch\n", __func__, _ep->name);
-               return -EINVAL;
-       }
-
-       /* hardware _could_ do smaller, but driver doesn't */
-       if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK
-            && le16_to_cpu(desc->wMaxPacketSize) != ep_maxpacket(ep))
-           || !desc->wMaxPacketSize) {
-               DEBUG("%s, bad %s maxpacket\n", __func__, _ep->name);
-               return -ERANGE;
-       }
-
-       dev = ep->dev;
-       if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) {
-               DEBUG("%s, bogus device state\n", __func__);
-               return -ESHUTDOWN;
-       }
-
-       spin_lock_irqsave(&ep->dev->lock, flags);
-
-       ep->stopped = 0;
-       ep->desc = desc;
-       ep->pio_irqs = 0;
-       ep->ep.maxpacket = le16_to_cpu(desc->wMaxPacketSize);
-
-       spin_unlock_irqrestore(&ep->dev->lock, flags);
-
-       /* Reset halt state (does flush) */
-       lh7a40x_set_halt(_ep, 0);
-
-       DEBUG("%s: enabled %s\n", __func__, _ep->name);
-       return 0;
-}
-
-/** Disable EP
- *  NOTE: Sets INDEX register
- */
-static int lh7a40x_ep_disable(struct usb_ep *_ep)
-{
-       struct lh7a40x_ep *ep;
-       unsigned long flags;
-
-       DEBUG("%s, %p\n", __func__, _ep);
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (!_ep || !ep->desc) {
-               DEBUG("%s, %s not enabled\n", __func__,
-                     _ep ? ep->ep.name : NULL);
-               return -EINVAL;
-       }
-
-       spin_lock_irqsave(&ep->dev->lock, flags);
-
-       usb_set_index(ep_index(ep));
-
-       /* Nuke all pending requests (does flush) */
-       nuke(ep, -ESHUTDOWN);
-
-       /* Disable ep IRQ */
-       pio_irq_disable(ep_index(ep));
-
-       ep->desc = 0;
-       ep->stopped = 1;
-
-       spin_unlock_irqrestore(&ep->dev->lock, flags);
-
-       DEBUG("%s: disabled %s\n", __func__, _ep->name);
-       return 0;
-}
-
-static struct usb_request *lh7a40x_alloc_request(struct usb_ep *ep,
-                                                gfp_t gfp_flags)
-{
-       struct lh7a40x_request *req;
-
-       DEBUG("%s, %p\n", __func__, ep);
-
-       req = kzalloc(sizeof(*req), gfp_flags);
-       if (!req)
-               return 0;
-
-       INIT_LIST_HEAD(&req->queue);
-
-       return &req->req;
-}
-
-static void lh7a40x_free_request(struct usb_ep *ep, struct usb_request *_req)
-{
-       struct lh7a40x_request *req;
-
-       DEBUG("%s, %p\n", __func__, ep);
-
-       req = container_of(_req, struct lh7a40x_request, req);
-       WARN_ON(!list_empty(&req->queue));
-       kfree(req);
-}
-
-/** Queue one request
- *  Kickstart transfer if needed
- *  NOTE: Sets INDEX register
- */
-static int lh7a40x_queue(struct usb_ep *_ep, struct usb_request *_req,
-                        gfp_t gfp_flags)
-{
-       struct lh7a40x_request *req;
-       struct lh7a40x_ep *ep;
-       struct lh7a40x_udc *dev;
-       unsigned long flags;
-
-       DEBUG("\n\n\n%s, %p\n", __func__, _ep);
-
-       req = container_of(_req, struct lh7a40x_request, req);
-       if (unlikely
-           (!_req || !_req->complete || !_req->buf
-            || !list_empty(&req->queue))) {
-               DEBUG("%s, bad params\n", __func__);
-               return -EINVAL;
-       }
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (unlikely(!_ep || (!ep->desc && ep->ep.name != ep0name))) {
-               DEBUG("%s, bad ep\n", __func__);
-               return -EINVAL;
-       }
-
-       dev = ep->dev;
-       if (unlikely(!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)) {
-               DEBUG("%s, bogus device state %p\n", __func__, dev->driver);
-               return -ESHUTDOWN;
-       }
-
-       DEBUG("%s queue req %p, len %d buf %p\n", _ep->name, _req, _req->length,
-             _req->buf);
-
-       spin_lock_irqsave(&dev->lock, flags);
-
-       _req->status = -EINPROGRESS;
-       _req->actual = 0;
-
-       /* kickstart this i/o queue? */
-       DEBUG("Add to %d Q %d %d\n", ep_index(ep), list_empty(&ep->queue),
-             ep->stopped);
-       if (list_empty(&ep->queue) && likely(!ep->stopped)) {
-               u32 csr;
-
-               if (unlikely(ep_index(ep) == 0)) {
-                       /* EP0 */
-                       list_add_tail(&req->queue, &ep->queue);
-                       lh7a40x_ep0_kick(dev, ep);
-                       req = 0;
-               } else if (ep_is_in(ep)) {
-                       /* EP1 & EP3 */
-                       usb_set_index(ep_index(ep));
-                       csr = usb_read(ep->csr1);
-                       pio_irq_enable(ep_index(ep));
-                       if ((csr & USB_IN_CSR1_FIFO_NOT_EMPTY) == 0) {
-                               if (write_fifo(ep, req) == 1)
-                                       req = 0;
-                       }
-               } else {
-                       /* EP2 */
-                       usb_set_index(ep_index(ep));
-                       csr = usb_read(ep->csr1);
-                       pio_irq_enable(ep_index(ep));
-                       if (!(csr & USB_OUT_CSR1_FIFO_FULL)) {
-                               if (read_fifo(ep, req) == 1)
-                                       req = 0;
-                       }
-               }
-       }
-
-       /* pio or dma irq handler advances the queue. */
-       if (likely(req != 0))
-               list_add_tail(&req->queue, &ep->queue);
-
-       spin_unlock_irqrestore(&dev->lock, flags);
-
-       return 0;
-}
-
-/* dequeue JUST ONE request */
-static int lh7a40x_dequeue(struct usb_ep *_ep, struct usb_request *_req)
-{
-       struct lh7a40x_ep *ep;
-       struct lh7a40x_request *req;
-       unsigned long flags;
-
-       DEBUG("%s, %p\n", __func__, _ep);
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (!_ep || ep->ep.name == ep0name)
-               return -EINVAL;
-
-       spin_lock_irqsave(&ep->dev->lock, flags);
-
-       /* make sure it's actually queued on this endpoint */
-       list_for_each_entry(req, &ep->queue, queue) {
-               if (&req->req == _req)
-                       break;
-       }
-       if (&req->req != _req) {
-               spin_unlock_irqrestore(&ep->dev->lock, flags);
-               return -EINVAL;
-       }
-
-       done(ep, req, -ECONNRESET);
-
-       spin_unlock_irqrestore(&ep->dev->lock, flags);
-       return 0;
-}
-
-/** Halt specific EP
- *  Return 0 if success
- *  NOTE: Sets INDEX register to EP !
- */
-static int lh7a40x_set_halt(struct usb_ep *_ep, int value)
-{
-       struct lh7a40x_ep *ep;
-       unsigned long flags;
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (unlikely(!_ep || (!ep->desc && ep->ep.name != ep0name))) {
-               DEBUG("%s, bad ep\n", __func__);
-               return -EINVAL;
-       }
-
-       usb_set_index(ep_index(ep));
-
-       DEBUG("%s, ep %d, val %d\n", __func__, ep_index(ep), value);
-
-       spin_lock_irqsave(&ep->dev->lock, flags);
-
-       if (ep_index(ep) == 0) {
-               /* EP0 */
-               usb_set(EP0_SEND_STALL, ep->csr1);
-       } else if (ep_is_in(ep)) {
-               u32 csr = usb_read(ep->csr1);
-               if (value && ((csr & USB_IN_CSR1_FIFO_NOT_EMPTY)
-                             || !list_empty(&ep->queue))) {
-                       /*
-                        * Attempts to halt IN endpoints will fail (returning -EAGAIN)
-                        * if any transfer requests are still queued, or if the controller
-                        * FIFO still holds bytes that the host hasn't collected.
-                        */
-                       spin_unlock_irqrestore(&ep->dev->lock, flags);
-                       DEBUG
-                           ("Attempt to halt IN endpoint failed (returning -EAGAIN) %d %d\n",
-                            (csr & USB_IN_CSR1_FIFO_NOT_EMPTY),
-                            !list_empty(&ep->queue));
-                       return -EAGAIN;
-               }
-               flush(ep);
-               if (value)
-                       usb_set(USB_IN_CSR1_SEND_STALL, ep->csr1);
-               else {
-                       usb_clear(USB_IN_CSR1_SEND_STALL, ep->csr1);
-                       usb_set(USB_IN_CSR1_CLR_DATA_TOGGLE, ep->csr1);
-               }
-
-       } else {
-
-               flush(ep);
-               if (value)
-                       usb_set(USB_OUT_CSR1_SEND_STALL, ep->csr1);
-               else {
-                       usb_clear(USB_OUT_CSR1_SEND_STALL, ep->csr1);
-                       usb_set(USB_OUT_CSR1_CLR_DATA_REG, ep->csr1);
-               }
-       }
-
-       if (value) {
-               ep->stopped = 1;
-       } else {
-               ep->stopped = 0;
-       }
-
-       spin_unlock_irqrestore(&ep->dev->lock, flags);
-
-       DEBUG("%s %s halted\n", _ep->name, value == 0 ? "NOT" : "IS");
-
-       return 0;
-}
-
-/** Return bytes in EP FIFO
- *  NOTE: Sets INDEX register to EP
- */
-static int lh7a40x_fifo_status(struct usb_ep *_ep)
-{
-       u32 csr;
-       int count = 0;
-       struct lh7a40x_ep *ep;
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (!_ep) {
-               DEBUG("%s, bad ep\n", __func__);
-               return -ENODEV;
-       }
-
-       DEBUG("%s, %d\n", __func__, ep_index(ep));
-
-       /* LPD can't report unclaimed bytes from IN fifos */
-       if (ep_is_in(ep))
-               return -EOPNOTSUPP;
-
-       usb_set_index(ep_index(ep));
-
-       csr = usb_read(ep->csr1);
-       if (ep->dev->gadget.speed != USB_SPEED_UNKNOWN ||
-           csr & USB_OUT_CSR1_OUT_PKT_RDY) {
-               count = usb_read(USB_OUT_FIFO_WC1);
-       }
-
-       return count;
-}
-
-/** Flush EP FIFO
- *  NOTE: Sets INDEX register to EP
- */
-static void lh7a40x_fifo_flush(struct usb_ep *_ep)
-{
-       struct lh7a40x_ep *ep;
-
-       ep = container_of(_ep, struct lh7a40x_ep, ep);
-       if (unlikely(!_ep || (!ep->desc && ep->ep.name != ep0name))) {
-               DEBUG("%s, bad ep\n", __func__);
-               return;
-       }
-
-       usb_set_index(ep_index(ep));
-       flush(ep);
-}
-
-/****************************************************************/
-/* End Point 0 related functions                                */
-/****************************************************************/
-
-/* return:  0 = still running, 1 = completed, negative = errno */
-static int write_fifo_ep0(struct lh7a40x_ep *ep, struct lh7a40x_request *req)
-{
-       u32 max;
-       unsigned count;
-       int is_last;
-
-       max = ep_maxpacket(ep);
-
-       DEBUG_EP0("%s\n", __func__);
-
-       count = write_packet(ep, req, max);
-
-       /* last packet is usually short (or a zlp) */
-       if (unlikely(count != max))
-               is_last = 1;
-       else {
-               if (likely(req->req.length != req->req.actual) || req->req.zero)
-                       is_last = 0;
-               else
-                       is_last = 1;
-       }
-
-       DEBUG_EP0("%s: wrote %s %d bytes%s %d left %p\n", __func__,
-                 ep->ep.name, count,
-                 is_last ? "/L" : "", req->req.length - req->req.actual, req);
-
-       /* requests complete when all IN data is in the FIFO */
-       if (is_last) {
-               done(ep, req, 0);
-               return 1;
-       }
-
-       return 0;
-}
-
-static __inline__ int lh7a40x_fifo_read(struct lh7a40x_ep *ep,
-                                       unsigned char *cp, int max)
-{
-       int bytes;
-       int count = usb_read(USB_OUT_FIFO_WC1);
-       volatile u32 *fifo = (volatile u32 *)ep->fifo;
-
-       if (count > max)
-               count = max;
-       bytes = count;
-       while (count--)
-               *cp++ = *fifo & 0xFF;
-       return bytes;
-}
-
-static __inline__ void lh7a40x_fifo_write(struct lh7a40x_ep *ep,
-                                         unsigned char *cp, int count)
-{
-       volatile u32 *fifo = (volatile u32 *)ep->fifo;
-       DEBUG_EP0("fifo_write: %d %d\n", ep_index(ep), count);
-       while (count--)
-               *fifo = *cp++;
-}
-
-static int read_fifo_ep0(struct lh7a40x_ep *ep, struct lh7a40x_request *req)
-{
-       u32 csr;
-       u8 *buf;
-       unsigned bufferspace, count, is_short;
-       volatile u32 *fifo = (volatile u32 *)ep->fifo;
-
-       DEBUG_EP0("%s\n", __func__);
-
-       csr = usb_read(USB_EP0_CSR);
-       if (!(csr & USB_OUT_CSR1_OUT_PKT_RDY))
-               return 0;
-
-       buf = req->req.buf + req->req.actual;
-       prefetchw(buf);
-       bufferspace = req->req.length - req->req.actual;
-
-       /* read all bytes from this packet */
-       if (likely(csr & EP0_OUT_PKT_RDY)) {
-               count = usb_read(USB_OUT_FIFO_WC1);
-               req->req.actual += min(count, bufferspace);
-       } else                  /* zlp */
-               count = 0;
-
-       is_short = (count < ep->ep.maxpacket);
-       DEBUG_EP0("read %s %02x, %d bytes%s req %p %d/%d\n",
-                 ep->ep.name, csr, count,
-                 is_short ? "/S" : "", req, req->req.actual, req->req.length);
-
-       while (likely(count-- != 0)) {
-               u8 byte = (u8) (*fifo & 0xff);
-
-               if (unlikely(bufferspace == 0)) {
-                       /* this happens when the driver's buffer
-                        * is smaller than what the host sent.
-                        * discard the extra data.
-                        */
-                       if (req->req.status != -EOVERFLOW)
-                               DEBUG_EP0("%s overflow %d\n", ep->ep.name,
-                                         count);
-                       req->req.status = -EOVERFLOW;
-               } else {
-                       *buf++ = byte;
-                       bufferspace--;
-               }
-       }
-
-       /* completion */
-       if (is_short || req->req.actual == req->req.length) {
-               done(ep, req, 0);
-               return 1;
-       }
-
-       /* finished that packet.  the next one may be waiting... */
-       return 0;
-}
-
-/**
- * udc_set_address - set the USB address for this device
- * @address:
- *
- * Called from control endpoint function after it decodes a set address setup packet.
- */
-static void udc_set_address(struct lh7a40x_udc *dev, unsigned char address)
-{
-       DEBUG_EP0("%s: %d\n", __func__, address);
-       /* c.f. 15.1.2.2 Table 15-4 address will be used after DATA_END is set */
-       dev->usb_address = address;
-       usb_set((address & USB_FA_FUNCTION_ADDR), USB_FA);
-       usb_set(USB_FA_ADDR_UPDATE | (address & USB_FA_FUNCTION_ADDR), USB_FA);
-       /* usb_read(USB_FA); */
-}
-
-/*
- * DATA_STATE_RECV (OUT_PKT_RDY)
- *      - if error
- *              set EP0_CLR_OUT | EP0_DATA_END | EP0_SEND_STALL bits
- *      - else
- *              set EP0_CLR_OUT bit
-                               if last set EP0_DATA_END bit
- */
-static void lh7a40x_ep0_out(struct lh7a40x_udc *dev, u32 csr)
-{
-       struct lh7a40x_request *req;
-       struct lh7a40x_ep *ep = &dev->ep[0];
-       int ret;
-
-       DEBUG_EP0("%s: %x\n", __func__, csr);
-
-       if (list_empty(&ep->queue))
-               req = 0;
-       else
-               req = list_entry(ep->queue.next, struct lh7a40x_request, queue);
-
-       if (req) {
-
-               if (req->req.length == 0) {
-                       DEBUG_EP0("ZERO LENGTH OUT!\n");
-                       usb_set((EP0_CLR_OUT | EP0_DATA_END), USB_EP0_CSR);
-                       dev->ep0state = WAIT_FOR_SETUP;
-                       return;
-               }
-               ret = read_fifo_ep0(ep, req);
-               if (ret) {
-                       /* Done! */
-                       DEBUG_EP0("%s: finished, waiting for status\n",
-                                 __func__);
-
-                       usb_set((EP0_CLR_OUT | EP0_DATA_END), USB_EP0_CSR);
-                       dev->ep0state = WAIT_FOR_SETUP;
-               } else {
-                       /* Not done yet.. */
-                       DEBUG_EP0("%s: not finished\n", __func__);
-                       usb_set(EP0_CLR_OUT, USB_EP0_CSR);
-               }
-       } else {
-               DEBUG_EP0("NO REQ??!\n");
-       }
-}
-
-/*
- * DATA_STATE_XMIT
- */
-static int lh7a40x_ep0_in(struct lh7a40x_udc *dev, u32 csr)
-{
-       struct lh7a40x_request *req;
-       struct lh7a40x_ep *ep = &dev->ep[0];
-       int ret, need_zlp = 0;
-
-       DEBUG_EP0("%s: %x\n", __func__, csr);
-
-       if (list_empty(&ep->queue))
-               req = 0;
-       else
-               req = list_entry(ep->queue.next, struct lh7a40x_request, queue);
-
-       if (!req) {
-               DEBUG_EP0("%s: NULL REQ\n", __func__);
-               return 0;
-       }
-
-       if (req->req.length == 0) {
-
-               usb_set((EP0_IN_PKT_RDY | EP0_DATA_END), USB_EP0_CSR);
-               dev->ep0state = WAIT_FOR_SETUP;
-               return 1;
-       }
-
-       if (req->req.length - req->req.actual == EP0_PACKETSIZE) {
-               /* Next write will end with the packet size, */
-               /* so we need Zero-length-packet */
-               need_zlp = 1;
-       }
-
-       ret = write_fifo_ep0(ep, req);
-
-       if (ret == 1 && !need_zlp) {
-               /* Last packet */
-               DEBUG_EP0("%s: finished, waiting for status\n", __func__);
-
-               usb_set((EP0_IN_PKT_RDY | EP0_DATA_END), USB_EP0_CSR);
-               dev->ep0state = WAIT_FOR_SETUP;
-       } else {
-               DEBUG_EP0("%s: not finished\n", __func__);
-               usb_set(EP0_IN_PKT_RDY, USB_EP0_CSR);
-       }
-
-       if (need_zlp) {
-               DEBUG_EP0("%s: Need ZLP!\n", __func__);
-               usb_set(EP0_IN_PKT_RDY, USB_EP0_CSR);
-               dev->ep0state = DATA_STATE_NEED_ZLP;
-       }
-
-       return 1;
-}
-
-static int lh7a40x_handle_get_status(struct lh7a40x_udc *dev,
-                                    struct usb_ctrlrequest *ctrl)
-{
-       struct lh7a40x_ep *ep0 = &dev->ep[0];
-       struct lh7a40x_ep *qep;
-       int reqtype = (ctrl->bRequestType & USB_RECIP_MASK);
-       u16 val = 0;
-
-       if (reqtype == USB_RECIP_INTERFACE) {
-               /* This is not supported.
-                * And according to the USB spec, this one does nothing..
-                * Just return 0
-                */
-               DEBUG_SETUP("GET_STATUS: USB_RECIP_INTERFACE\n");
-       } else if (reqtype == USB_RECIP_DEVICE) {
-               DEBUG_SETUP("GET_STATUS: USB_RECIP_DEVICE\n");
-               val |= (1 << 0);        /* Self powered */
-               /*val |= (1<<1); *//* Remote wakeup */
-       } else if (reqtype == USB_RECIP_ENDPOINT) {
-               int ep_num = (ctrl->wIndex & ~USB_DIR_IN);
-
-               DEBUG_SETUP
-                   ("GET_STATUS: USB_RECIP_ENDPOINT (%d), ctrl->wLength = %d\n",
-                    ep_num, ctrl->wLength);
-
-               if (ctrl->wLength > 2 || ep_num > 3)
-                       return -EOPNOTSUPP;
-
-               qep = &dev->ep[ep_num];
-               if (ep_is_in(qep) != ((ctrl->wIndex & USB_DIR_IN) ? 1 : 0)
-                   && ep_index(qep) != 0) {
-                       return -EOPNOTSUPP;
-               }
-
-               usb_set_index(ep_index(qep));
-
-               /* Return status on next IN token */
-               switch (qep->ep_type) {
-               case ep_control:
-                       val =
-                           (usb_read(qep->csr1) & EP0_SEND_STALL) ==
-                           EP0_SEND_STALL;
-                       break;
-               case ep_bulk_in:
-               case ep_interrupt:
-                       val =
-                           (usb_read(qep->csr1) & USB_IN_CSR1_SEND_STALL) ==
-                           USB_IN_CSR1_SEND_STALL;
-                       break;
-               case ep_bulk_out:
-                       val =
-                           (usb_read(qep->csr1) & USB_OUT_CSR1_SEND_STALL) ==
-                           USB_OUT_CSR1_SEND_STALL;
-                       break;
-               }
-
-               /* Back to EP0 index */
-               usb_set_index(0);
-
-               DEBUG_SETUP("GET_STATUS, ep: %d (%x), val = %d\n", ep_num,
-                           ctrl->wIndex, val);
-       } else {
-               DEBUG_SETUP("Unknown REQ TYPE: %d\n", reqtype);
-               return -EOPNOTSUPP;
-       }
-
-       /* Clear "out packet ready" */
-       usb_set((EP0_CLR_OUT), USB_EP0_CSR);
-       /* Put status to FIFO */
-       lh7a40x_fifo_write(ep0, (u8 *) & val, sizeof(val));
-       /* Issue "In packet ready" */
-       usb_set((EP0_IN_PKT_RDY | EP0_DATA_END), USB_EP0_CSR);
-
-       return 0;
-}
-
-/*
- * WAIT_FOR_SETUP (OUT_PKT_RDY)
- *      - read data packet from EP0 FIFO
- *      - decode command
- *      - if error
- *              set EP0_CLR_OUT | EP0_DATA_END | EP0_SEND_STALL bits
- *      - else
- *              set EP0_CLR_OUT | EP0_DATA_END bits
- */
-static void lh7a40x_ep0_setup(struct lh7a40x_udc *dev, u32 csr)
-{
-       struct lh7a40x_ep *ep = &dev->ep[0];
-       struct usb_ctrlrequest ctrl;
-       int i, bytes, is_in;
-
-       DEBUG_SETUP("%s: %x\n", __func__, csr);
-
-       /* Nuke all previous transfers */
-       nuke(ep, -EPROTO);
-
-       /* read control req from fifo (8 bytes) */
-       bytes = lh7a40x_fifo_read(ep, (unsigned char *)&ctrl, 8);
-
-       DEBUG_SETUP("Read CTRL REQ %d bytes\n", bytes);
-       DEBUG_SETUP("CTRL.bRequestType = %d (is_in %d)\n", ctrl.bRequestType,
-                   ctrl.bRequestType == USB_DIR_IN);
-       DEBUG_SETUP("CTRL.bRequest = %d\n", ctrl.bRequest);
-       DEBUG_SETUP("CTRL.wLength = %d\n", ctrl.wLength);
-       DEBUG_SETUP("CTRL.wValue = %d (%d)\n", ctrl.wValue, ctrl.wValue >> 8);
-       DEBUG_SETUP("CTRL.wIndex = %d\n", ctrl.wIndex);
-
-       /* Set direction of EP0 */
-       if (likely(ctrl.bRequestType & USB_DIR_IN)) {
-               ep->bEndpointAddress |= USB_DIR_IN;
-               is_in = 1;
-       } else {
-               ep->bEndpointAddress &= ~USB_DIR_IN;
-               is_in = 0;
-       }
-
-       dev->req_pending = 1;
-
-       /* Handle some SETUP packets ourselves */
-       switch (ctrl.bRequest) {
-       case USB_REQ_SET_ADDRESS:
-               if (ctrl.bRequestType != (USB_TYPE_STANDARD | USB_RECIP_DEVICE))
-                       break;
-
-               DEBUG_SETUP("USB_REQ_SET_ADDRESS (%d)\n", ctrl.wValue);
-               udc_set_address(dev, ctrl.wValue);
-               usb_set((EP0_CLR_OUT | EP0_DATA_END), USB_EP0_CSR);
-               return;
-
-       case USB_REQ_GET_STATUS:{
-                       if (lh7a40x_handle_get_status(dev, &ctrl) == 0)
-                               return;
-
-       case USB_REQ_CLEAR_FEATURE:
-       case USB_REQ_SET_FEATURE:
-                       if (ctrl.bRequestType == USB_RECIP_ENDPOINT) {
-                               struct lh7a40x_ep *qep;
-                               int ep_num = (ctrl.wIndex & 0x0f);
-
-                               /* Support only HALT feature */
-                               if (ctrl.wValue != 0 || ctrl.wLength != 0
-                                   || ep_num > 3 || ep_num < 1)
-                                       break;
-
-                               qep = &dev->ep[ep_num];
-                               spin_unlock(&dev->lock);
-                               if (ctrl.bRequest == USB_REQ_SET_FEATURE) {
-                                       DEBUG_SETUP("SET_FEATURE (%d)\n",
-                                                   ep_num);
-                                       lh7a40x_set_halt(&qep->ep, 1);
-                               } else {
-                                       DEBUG_SETUP("CLR_FEATURE (%d)\n",
-                                                   ep_num);
-                                       lh7a40x_set_halt(&qep->ep, 0);
-                               }
-                               spin_lock(&dev->lock);
-                               usb_set_index(0);
-
-                               /* Reply with a ZLP on next IN token */
-                               usb_set((EP0_CLR_OUT | EP0_DATA_END),
-                                       USB_EP0_CSR);
-                               return;
-                       }
-                       break;
-               }
-
-       default:
-               break;
-       }
-
-       if (likely(dev->driver)) {
-               /* device-2-host (IN) or no data setup command, process immediately */
-               spin_unlock(&dev->lock);
-               i = dev->driver->setup(&dev->gadget, &ctrl);
-               spin_lock(&dev->lock);
-
-               if (i < 0) {
-                       /* setup processing failed, force stall */
-                       DEBUG_SETUP
-                           ("  --> ERROR: gadget setup FAILED (stalling), setup returned %d\n",
-                            i);
-                       usb_set_index(0);
-                       usb_set((EP0_CLR_OUT | EP0_DATA_END | EP0_SEND_STALL),
-                               USB_EP0_CSR);
-
-                       /* ep->stopped = 1; */
-                       dev->ep0state = WAIT_FOR_SETUP;
-               }
-       }
-}
-
-/*
- * DATA_STATE_NEED_ZLP
- */
-static void lh7a40x_ep0_in_zlp(struct lh7a40x_udc *dev, u32 csr)
-{
-       DEBUG_EP0("%s: %x\n", __func__, csr);
-
-       /* c.f. Table 15-14 */
-       usb_set((EP0_IN_PKT_RDY | EP0_DATA_END), USB_EP0_CSR);
-       dev->ep0state = WAIT_FOR_SETUP;
-}
-
-/*
- * handle ep0 interrupt
- */
-static void lh7a40x_handle_ep0(struct lh7a40x_udc *dev, u32 intr)
-{
-       struct lh7a40x_ep *ep = &dev->ep[0];
-       u32 csr;
-
-       /* Set index 0 */
-       usb_set_index(0);
-       csr = usb_read(USB_EP0_CSR);
-
-       DEBUG_EP0("%s: csr = %x\n", __func__, csr);
-
-       /*
-        * For overview of what we should be doing see c.f. Chapter 18.1.2.4
-        * We will follow that outline here modified by our own global state
-        * indication which provides hints as to what we think should be
-        * happening..
-        */
-
-       /*
-        * if SENT_STALL is set
-        *      - clear the SENT_STALL bit
-        */
-       if (csr & EP0_SENT_STALL) {
-               DEBUG_EP0("%s: EP0_SENT_STALL is set: %x\n", __func__, csr);
-               usb_clear((EP0_SENT_STALL | EP0_SEND_STALL), USB_EP0_CSR);
-               nuke(ep, -ECONNABORTED);
-               dev->ep0state = WAIT_FOR_SETUP;
-               return;
-       }
-
-       /*
-        * if a transfer is in progress && IN_PKT_RDY and OUT_PKT_RDY are clear
-        *      - fill EP0 FIFO
-        *      - if last packet
-        *      -       set IN_PKT_RDY | DATA_END
-        *      - else
-        *              set IN_PKT_RDY
-        */
-       if (!(csr & (EP0_IN_PKT_RDY | EP0_OUT_PKT_RDY))) {
-               DEBUG_EP0("%s: IN_PKT_RDY and OUT_PKT_RDY are clear\n",
-                         __func__);
-
-               switch (dev->ep0state) {
-               case DATA_STATE_XMIT:
-                       DEBUG_EP0("continue with DATA_STATE_XMIT\n");
-                       lh7a40x_ep0_in(dev, csr);
-                       return;
-               case DATA_STATE_NEED_ZLP:
-                       DEBUG_EP0("continue with DATA_STATE_NEED_ZLP\n");
-                       lh7a40x_ep0_in_zlp(dev, csr);
-                       return;
-               default:
-                       /* Stall? */
-                       DEBUG_EP0("Odd state!! state = %s\n",
-                                 state_names[dev->ep0state]);
-                       dev->ep0state = WAIT_FOR_SETUP;
-                       /* nuke(ep, 0); */
-                       /* usb_set(EP0_SEND_STALL, ep->csr1); */
-                       break;
-               }
-       }
-
-       /*
-        * if SETUP_END is set
-        *      - abort the last transfer
-        *      - set SERVICED_SETUP_END_BIT
-        */
-       if (csr & EP0_SETUP_END) {
-               DEBUG_EP0("%s: EP0_SETUP_END is set: %x\n", __func__, csr);
-
-               usb_set(EP0_CLR_SETUP_END, USB_EP0_CSR);
-
-               nuke(ep, 0);
-               dev->ep0state = WAIT_FOR_SETUP;
-       }
-
-       /*
-        * if EP0_OUT_PKT_RDY is set
-        *      - read data packet from EP0 FIFO
-        *      - decode command
-        *      - if error
-        *              set SERVICED_OUT_PKT_RDY | DATA_END bits | SEND_STALL
-        *      - else
-        *              set SERVICED_OUT_PKT_RDY | DATA_END bits
-        */
-       if (csr & EP0_OUT_PKT_RDY) {
-
-               DEBUG_EP0("%s: EP0_OUT_PKT_RDY is set: %x\n", __func__,
-                         csr);
-
-               switch (dev->ep0state) {
-               case WAIT_FOR_SETUP:
-                       DEBUG_EP0("WAIT_FOR_SETUP\n");
-                       lh7a40x_ep0_setup(dev, csr);
-                       break;
-
-               case DATA_STATE_RECV:
-                       DEBUG_EP0("DATA_STATE_RECV\n");
-                       lh7a40x_ep0_out(dev, csr);
-                       break;
-
-               default:
-                       /* send stall? */
-                       DEBUG_EP0("strange state!! 2. send stall? state = %d\n",
-                                 dev->ep0state);
-                       break;
-               }
-       }
-}
-
-static void lh7a40x_ep0_kick(struct lh7a40x_udc *dev, struct lh7a40x_ep *ep)
-{
-       u32 csr;
-
-       usb_set_index(0);
-       csr = usb_read(USB_EP0_CSR);
-
-       DEBUG_EP0("%s: %x\n", __func__, csr);
-
-       /* Clear "out packet ready" */
-       usb_set(EP0_CLR_OUT, USB_EP0_CSR);
-
-       if (ep_is_in(ep)) {
-               dev->ep0state = DATA_STATE_XMIT;
-               lh7a40x_ep0_in(dev, csr);
-       } else {
-               dev->ep0state = DATA_STATE_RECV;
-               lh7a40x_ep0_out(dev, csr);
-       }
-}
-
-/* ---------------------------------------------------------------------------
- *     device-scoped parts of the api to the usb controller hardware
- * ---------------------------------------------------------------------------
- */
-
-static int lh7a40x_udc_get_frame(struct usb_gadget *_gadget)
-{
-       u32 frame1 = usb_read(USB_FRM_NUM1);    /* Least significant 8 bits */
-       u32 frame2 = usb_read(USB_FRM_NUM2);    /* Most significant 3 bits */
-       DEBUG("%s, %p\n", __func__, _gadget);
-       return ((frame2 & 0x07) << 8) | (frame1 & 0xff);
-}
-
-static int lh7a40x_udc_wakeup(struct usb_gadget *_gadget)
-{
-       /* host may not have enabled remote wakeup */
-       /*if ((UDCCS0 & UDCCS0_DRWF) == 0)
-          return -EHOSTUNREACH;
-          udc_set_mask_UDCCR(UDCCR_RSM); */
-       return -ENOTSUPP;
-}
-
-static const struct usb_gadget_ops lh7a40x_udc_ops = {
-       .get_frame = lh7a40x_udc_get_frame,
-       .wakeup = lh7a40x_udc_wakeup,
-       /* current versions must always be self-powered */
-};
-
-static void nop_release(struct device *dev)
-{
-       DEBUG("%s %s\n", __func__, dev_name(dev));
-}
-
-static struct lh7a40x_udc memory = {
-       .usb_address = 0,
-
-       .gadget = {
-                  .ops = &lh7a40x_udc_ops,
-                  .ep0 = &memory.ep[0].ep,
-                  .name = driver_name,
-                  .dev = {
-                          .init_name = "gadget",
-                          .release = nop_release,
-                          },
-                  },
-
-       /* control endpoint */
-       .ep[0] = {
-                 .ep = {
-                        .name = ep0name,
-                        .ops = &lh7a40x_ep_ops,
-                        .maxpacket = EP0_PACKETSIZE,
-                        },
-                 .dev = &memory,
-
-                 .bEndpointAddress = 0,
-                 .bmAttributes = 0,
-
-                 .ep_type = ep_control,
-                 .fifo = io_p2v(USB_EP0_FIFO),
-                 .csr1 = USB_EP0_CSR,
-                 .csr2 = USB_EP0_CSR,
-                 },
-
-       /* first group of endpoints */
-       .ep[1] = {
-                 .ep = {
-                        .name = "ep1in-bulk",
-                        .ops = &lh7a40x_ep_ops,
-                        .maxpacket = 64,
-                        },
-                 .dev = &memory,
-
-                 .bEndpointAddress = USB_DIR_IN | 1,
-                 .bmAttributes = USB_ENDPOINT_XFER_BULK,
-
-                 .ep_type = ep_bulk_in,
-                 .fifo = io_p2v(USB_EP1_FIFO),
-                 .csr1 = USB_IN_CSR1,
-                 .csr2 = USB_IN_CSR2,
-                 },
-
-       .ep[2] = {
-                 .ep = {
-                        .name = "ep2out-bulk",
-                        .ops = &lh7a40x_ep_ops,
-                        .maxpacket = 64,
-                        },
-                 .dev = &memory,
-
-                 .bEndpointAddress = 2,
-                 .bmAttributes = USB_ENDPOINT_XFER_BULK,
-
-                 .ep_type = ep_bulk_out,
-                 .fifo = io_p2v(USB_EP2_FIFO),
-                 .csr1 = USB_OUT_CSR1,
-                 .csr2 = USB_OUT_CSR2,
-                 },
-
-       .ep[3] = {
-                 .ep = {
-                        .name = "ep3in-int",
-                        .ops = &lh7a40x_ep_ops,
-                        .maxpacket = 64,
-                        },
-                 .dev = &memory,
-
-                 .bEndpointAddress = USB_DIR_IN | 3,
-                 .bmAttributes = USB_ENDPOINT_XFER_INT,
-
-                 .ep_type = ep_interrupt,
-                 .fifo = io_p2v(USB_EP3_FIFO),
-                 .csr1 = USB_IN_CSR1,
-                 .csr2 = USB_IN_CSR2,
-                 },
-};
-
-/*
- *     probe - binds to the platform device
- */
-static int lh7a40x_udc_probe(struct platform_device *pdev)
-{
-       struct lh7a40x_udc *dev = &memory;
-       int retval;
-
-       DEBUG("%s: %p\n", __func__, pdev);
-
-       spin_lock_init(&dev->lock);
-       dev->dev = &pdev->dev;
-
-       device_initialize(&dev->gadget.dev);
-       dev->gadget.dev.parent = &pdev->dev;
-
-       the_controller = dev;
-       platform_set_drvdata(pdev, dev);
-
-       udc_disable(dev);
-       udc_reinit(dev);
-
-       /* irq setup after old hardware state is cleaned up */
-       retval =
-           request_irq(IRQ_USBINTR, lh7a40x_udc_irq, IRQF_DISABLED, driver_name,
-                       dev);
-       if (retval != 0) {
-               DEBUG(KERN_ERR "%s: can't get irq %i, err %d\n", driver_name,
-                     IRQ_USBINTR, retval);
-               return -EBUSY;
-       }
-
-       create_proc_files();
-
-       return retval;
-}
-
-static int lh7a40x_udc_remove(struct platform_device *pdev)
-{
-       struct lh7a40x_udc *dev = platform_get_drvdata(pdev);
-
-       DEBUG("%s: %p\n", __func__, pdev);
-
-       if (dev->driver)
-               return -EBUSY;
-
-       udc_disable(dev);
-       remove_proc_files();
-
-       free_irq(IRQ_USBINTR, dev);
-
-       platform_set_drvdata(pdev, 0);
-
-       the_controller = 0;
-
-       return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-static struct platform_driver udc_driver = {
-       .probe = lh7a40x_udc_probe,
-       .remove = lh7a40x_udc_remove,
-           /* FIXME power management support */
-           /* .suspend = ... disable UDC */
-           /* .resume = ... re-enable UDC */
-       .driver = {
-               .name = (char *)driver_name,
-               .owner = THIS_MODULE,
-       },
-};
-
-static int __init udc_init(void)
-{
-       DEBUG("%s: %s version %s\n", __func__, driver_name, DRIVER_VERSION);
-       return platform_driver_register(&udc_driver);
-}
-
-static void __exit udc_exit(void)
-{
-       platform_driver_unregister(&udc_driver);
-}
-
-module_init(udc_init);
-module_exit(udc_exit);
-
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_AUTHOR("Mikko Lahteenmaki, Bo Henriksen");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:lh7a40x_udc");
diff --git a/drivers/usb/gadget/lh7a40x_udc.h b/drivers/usb/gadget/lh7a40x_udc.h
deleted file mode 100644 (file)
index ca86120..0000000
+++ /dev/null
@@ -1,259 +0,0 @@
-/*
- * linux/drivers/usb/gadget/lh7a40x_udc.h
- * Sharp LH7A40x on-chip full speed USB device controllers
- *
- * Copyright (C) 2004 Mikko Lahteenmaki, Nordic ID
- * Copyright (C) 2004 Bo Henriksen, Nordic ID
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#ifndef __LH7A40X_H_
-#define __LH7A40X_H_
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/ioport.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/delay.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/timer.h>
-#include <linux/list.h>
-#include <linux/interrupt.h>
-#include <linux/proc_fs.h>
-#include <linux/mm.h>
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-
-#include <asm/byteorder.h>
-#include <asm/dma.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/unaligned.h>
-#include <mach/hardware.h>
-
-#include <linux/usb/ch9.h>
-#include <linux/usb/gadget.h>
-
-/*
- * Memory map
- */
-
-#define USB_FA                                 0x80000200      // function address register
-#define USB_PM                                 0x80000204      // power management register
-
-#define USB_IN_INT                             0x80000208      // IN interrupt register bank (EP0-EP3)
-#define USB_OUT_INT                            0x80000210      // OUT interrupt register bank (EP2)
-#define USB_INT                                        0x80000218      // interrupt register bank
-
-#define USB_IN_INT_EN                  0x8000021C      // IN interrupt enable register bank
-#define USB_OUT_INT_EN                 0x80000224      // OUT interrupt enable register bank
-#define USB_INT_EN                             0x8000022C      // USB interrupt enable register bank
-
-#define USB_FRM_NUM1                   0x80000230      // Frame number1 register
-#define USB_FRM_NUM2                   0x80000234      // Frame number2 register
-#define USB_INDEX                              0x80000238      // index register
-
-#define USB_IN_MAXP                            0x80000240      // IN MAXP register
-#define USB_IN_CSR1                            0x80000244      // IN CSR1 register/EP0 CSR register
-#define USB_EP0_CSR                            0x80000244      // IN CSR1 register/EP0 CSR register
-#define USB_IN_CSR2                            0x80000248      // IN CSR2 register
-#define USB_OUT_MAXP                   0x8000024C      // OUT MAXP register
-
-#define USB_OUT_CSR1                   0x80000250      // OUT CSR1 register
-#define USB_OUT_CSR2                   0x80000254      // OUT CSR2 register
-#define USB_OUT_FIFO_WC1               0x80000258      // OUT FIFO write count1 register
-#define USB_OUT_FIFO_WC2               0x8000025C      // OUT FIFO write count2 register
-
-#define USB_RESET                              0x8000044C      // USB reset register
-
-#define        USB_EP0_FIFO                    0x80000280
-#define        USB_EP1_FIFO                    0x80000284
-#define        USB_EP2_FIFO                    0x80000288
-#define        USB_EP3_FIFO                    0x8000028c
-
-/*
- * USB reset register
- */
-#define USB_RESET_APB                  (1<<1)  //resets USB APB control side WRITE
-#define USB_RESET_IO                   (1<<0)  //resets USB IO side WRITE
-
-/*
- * USB function address register
- */
-#define USB_FA_ADDR_UPDATE             (1<<7)
-#define USB_FA_FUNCTION_ADDR   (0x7F)
-
-/*
- * Power Management register
- */
-#define PM_USB_DCP                             (1<<5)
-#define PM_USB_ENABLE                  (1<<4)
-#define PM_USB_RESET                   (1<<3)
-#define PM_UC_RESUME                   (1<<2)
-#define PM_SUSPEND_MODE                        (1<<1)
-#define PM_ENABLE_SUSPEND              (1<<0)
-
-/*
- * IN interrupt register
- */
-#define USB_IN_INT_EP3                         (1<<3)
-#define USB_IN_INT_EP1                         (1<<1)
-#define USB_IN_INT_EP0                         (1<<0)
-
-/*
- * OUT interrupt register
- */
-#define USB_OUT_INT_EP2                                (1<<2)
-
-/*
- * USB interrupt register
- */
-#define USB_INT_RESET_INT                      (1<<2)
-#define USB_INT_RESUME_INT                     (1<<1)
-#define USB_INT_SUSPEND_INT                    (1<<0)
-
-/*
- * USB interrupt enable register
- */
-#define USB_INT_EN_USB_RESET_INTER             (1<<2)
-#define USB_INT_EN_RESUME_INTER                        (1<<1)
-#define USB_INT_EN_SUSPEND_INTER               (1<<0)
-
-/*
- * INCSR1 register
- */
-#define USB_IN_CSR1_CLR_DATA_TOGGLE            (1<<6)
-#define USB_IN_CSR1_SENT_STALL                 (1<<5)
-#define USB_IN_CSR1_SEND_STALL                 (1<<4)
-#define USB_IN_CSR1_FIFO_FLUSH                 (1<<3)
-#define USB_IN_CSR1_FIFO_NOT_EMPTY             (1<<1)
-#define USB_IN_CSR1_IN_PKT_RDY                 (1<<0)
-
-/*
- * INCSR2 register
- */
-#define USB_IN_CSR2_AUTO_SET                   (1<<7)
-#define USB_IN_CSR2_USB_DMA_EN                 (1<<4)
-
-/*
- * OUT CSR1 register
- */
-#define USB_OUT_CSR1_CLR_DATA_REG              (1<<7)
-#define USB_OUT_CSR1_SENT_STALL                        (1<<6)
-#define USB_OUT_CSR1_SEND_STALL                        (1<<5)
-#define USB_OUT_CSR1_FIFO_FLUSH                        (1<<4)
-#define USB_OUT_CSR1_FIFO_FULL                 (1<<1)
-#define USB_OUT_CSR1_OUT_PKT_RDY               (1<<0)
-
-/*
- * OUT CSR2 register
- */
-#define USB_OUT_CSR2_AUTO_CLR                  (1<<7)
-#define USB_OUT_CSR2_USB_DMA_EN                        (1<<4)
-
-/*
- * EP0 CSR
- */
-#define EP0_CLR_SETUP_END              (1<<7)  /* Clear "Setup Ends" Bit (w) */
-#define EP0_CLR_OUT                            (1<<6)  /* Clear "Out packet ready" Bit (w) */
-#define EP0_SEND_STALL                 (1<<5)  /* Send STALL Handshake (rw) */
-#define EP0_SETUP_END                  (1<<4)  /* Setup Ends (r) */
-
-#define EP0_DATA_END                   (1<<3)  /* Data end (rw) */
-#define EP0_SENT_STALL                 (1<<2)  /* Sent Stall Handshake (r) */
-#define EP0_IN_PKT_RDY                 (1<<1)  /* In packet ready (rw) */
-#define EP0_OUT_PKT_RDY                        (1<<0)  /* Out packet ready (r) */
-
-/* general CSR */
-#define OUT_PKT_RDY            (1<<0)
-#define IN_PKT_RDY             (1<<0)
-
-/*
- * IN/OUT MAXP register
- */
-#define USB_OUT_MAXP_MAXP                      (0xF)
-#define USB_IN_MAXP_MAXP                       (0xF)
-
-// Max packet size
-//#define EP0_PACKETSIZE        0x10
-#define EP0_PACKETSIZE         0x8
-#define EP0_MAXPACKETSIZE      0x10
-
-#define UDC_MAX_ENDPOINTS       4
-
-#define WAIT_FOR_SETUP          0
-#define DATA_STATE_XMIT         1
-#define DATA_STATE_NEED_ZLP     2
-#define WAIT_FOR_OUT_STATUS     3
-#define DATA_STATE_RECV         4
-
-/* ********************************************************************************************* */
-/* IO
- */
-
-typedef enum ep_type {
-       ep_control, ep_bulk_in, ep_bulk_out, ep_interrupt
-} ep_type_t;
-
-struct lh7a40x_ep {
-       struct usb_ep ep;
-       struct lh7a40x_udc *dev;
-
-       const struct usb_endpoint_descriptor *desc;
-       struct list_head queue;
-       unsigned long pio_irqs;
-
-       u8 stopped;
-       u8 bEndpointAddress;
-       u8 bmAttributes;
-
-       ep_type_t ep_type;
-       u32 fifo;
-       u32 csr1;
-       u32 csr2;
-};
-
-struct lh7a40x_request {
-       struct usb_request req;
-       struct list_head queue;
-};
-
-struct lh7a40x_udc {
-       struct usb_gadget gadget;
-       struct usb_gadget_driver *driver;
-       struct device *dev;
-       spinlock_t lock;
-
-       int ep0state;
-       struct lh7a40x_ep ep[UDC_MAX_ENDPOINTS];
-
-       unsigned char usb_address;
-
-       unsigned req_pending:1, req_std:1, req_config:1;
-};
-
-extern struct lh7a40x_udc *the_controller;
-
-#define ep_is_in(EP)           (((EP)->bEndpointAddress&USB_DIR_IN)==USB_DIR_IN)
-#define ep_index(EP)           ((EP)->bEndpointAddress&0xF)
-#define ep_maxpacket(EP)       ((EP)->ep.maxpacket)
-
-#endif
index 759a12ff8048b64dec471ee18a1f2e4a937ae209..b426c1e8a679c5cefec61e97746ef74aa2b789f7 100644 (file)
@@ -1023,11 +1023,6 @@ MODULE_LICENSE ("GPL");
 #define OMAP3_PLATFORM_DRIVER  ohci_hcd_omap3_driver
 #endif
 
-#ifdef CONFIG_ARCH_LH7A404
-#include "ohci-lh7a404.c"
-#define PLATFORM_DRIVER                ohci_hcd_lh7a404_driver
-#endif
-
 #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
 #include "ohci-pxa27x.c"
 #define PLATFORM_DRIVER                ohci_hcd_pxa27x_driver
diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c
deleted file mode 100644 (file)
index 18d39f0..0000000
+++ /dev/null
@@ -1,252 +0,0 @@
-/*
- * OHCI HCD (Host Controller Driver) for USB.
- *
- * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
- * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
- * (C) Copyright 2002 Hewlett-Packard Company
- *
- * Bus Glue for Sharp LH7A404
- *
- * Written by Christopher Hoover <ch@hpl.hp.com>
- * Based on fragments of previous driver by Russell King et al.
- *
- * Modified for LH7A404 from ohci-sa1111.c
- *  by Durgesh Pattamatta <pattamattad@sharpsec.com>
- *
- * This file is licenced under the GPL.
- */
-
-#include <linux/platform_device.h>
-#include <linux/signal.h>
-
-#include <mach/hardware.h>
-
-
-extern int usb_disabled(void);
-
-/*-------------------------------------------------------------------------*/
-
-static void lh7a404_start_hc(struct platform_device *dev)
-{
-       printk(KERN_DEBUG "%s: starting LH7A404 OHCI USB Controller\n",
-              __FILE__);
-
-       /*
-        * Now, carefully enable the USB clock, and take
-        * the USB host controller out of reset.
-        */
-       CSC_PWRCNT |= CSC_PWRCNT_USBH_EN; /* Enable clock */
-       udelay(1000);
-       USBH_CMDSTATUS = OHCI_HCR;
-
-       printk(KERN_DEBUG "%s: Clock to USB host has been enabled \n", __FILE__);
-}
-
-static void lh7a404_stop_hc(struct platform_device *dev)
-{
-       printk(KERN_DEBUG "%s: stopping LH7A404 OHCI USB Controller\n",
-              __FILE__);
-
-       CSC_PWRCNT &= ~CSC_PWRCNT_USBH_EN; /* Disable clock */
-}
-
-
-/*-------------------------------------------------------------------------*/
-
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
-
-
-/**
- * usb_hcd_lh7a404_probe - initialize LH7A404-based HCDs
- * Context: !in_interrupt()
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- *
- */
-int usb_hcd_lh7a404_probe (const struct hc_driver *driver,
-                         struct platform_device *dev)
-{
-       int retval;
-       struct usb_hcd *hcd;
-
-       if (dev->resource[1].flags != IORESOURCE_IRQ) {
-               pr_debug("resource[1] is not IORESOURCE_IRQ");
-               return -ENOMEM;
-       }
-
-       hcd = usb_create_hcd(driver, &dev->dev, "lh7a404");
-       if (!hcd)
-               return -ENOMEM;
-       hcd->rsrc_start = dev->resource[0].start;
-       hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
-
-       if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
-               pr_debug("request_mem_region failed");
-               retval = -EBUSY;
-               goto err1;
-       }
-
-       hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-       if (!hcd->regs) {
-               pr_debug("ioremap failed");
-               retval = -ENOMEM;
-               goto err2;
-       }
-
-       lh7a404_start_hc(dev);
-       ohci_hcd_init(hcd_to_ohci(hcd));
-
-       retval = usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED);
-       if (retval == 0)
-               return retval;
-
-       lh7a404_stop_hc(dev);
-       iounmap(hcd->regs);
- err2:
-       release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
- err1:
-       usb_put_hcd(hcd);
-       return retval;
-}
-
-
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
-
-/**
- * usb_hcd_lh7a404_remove - shutdown processing for LH7A404-based HCDs
- * @dev: USB Host Controller being removed
- * Context: !in_interrupt()
- *
- * Reverses the effect of usb_hcd_lh7a404_probe(), first invoking
- * the HCD's stop() method.  It is always called from a thread
- * context, normally "rmmod", "apmd", or something similar.
- *
- */
-void usb_hcd_lh7a404_remove (struct usb_hcd *hcd, struct platform_device *dev)
-{
-       usb_remove_hcd(hcd);
-       lh7a404_stop_hc(dev);
-       iounmap(hcd->regs);
-       release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-       usb_put_hcd(hcd);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static int __devinit
-ohci_lh7a404_start (struct usb_hcd *hcd)
-{
-       struct ohci_hcd *ohci = hcd_to_ohci (hcd);
-       int             ret;
-
-       ohci_dbg (ohci, "ohci_lh7a404_start, ohci:%p", ohci);
-       if ((ret = ohci_init(ohci)) < 0)
-               return ret;
-
-       if ((ret = ohci_run (ohci)) < 0) {
-               err ("can't start %s", hcd->self.bus_name);
-               ohci_stop (hcd);
-               return ret;
-       }
-       return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ohci_lh7a404_hc_driver = {
-       .description =          hcd_name,
-       .product_desc =         "LH7A404 OHCI",
-       .hcd_priv_size =        sizeof(struct ohci_hcd),
-
-       /*
-        * generic hardware linkage
-        */
-       .irq =                  ohci_irq,
-       .flags =                HCD_USB11 | HCD_MEMORY,
-
-       /*
-        * basic lifecycle operations
-        */
-       .start =                ohci_lh7a404_start,
-       .stop =                 ohci_stop,
-       .shutdown =             ohci_shutdown,
-
-       /*
-        * managing i/o requests and associated device resources
-        */
-       .urb_enqueue =          ohci_urb_enqueue,
-       .urb_dequeue =          ohci_urb_dequeue,
-       .endpoint_disable =     ohci_endpoint_disable,
-
-       /*
-        * scheduling support
-        */
-       .get_frame_number =     ohci_get_frame,
-
-       /*
-        * root hub support
-        */
-       .hub_status_data =      ohci_hub_status_data,
-       .hub_control =          ohci_hub_control,
-#ifdef CONFIG_PM
-       .bus_suspend =          ohci_bus_suspend,
-       .bus_resume =           ohci_bus_resume,
-#endif
-       .start_port_reset =     ohci_start_port_reset,
-};
-
-/*-------------------------------------------------------------------------*/
-
-static int ohci_hcd_lh7a404_drv_probe(struct platform_device *pdev)
-{
-       int ret;
-
-       pr_debug ("In ohci_hcd_lh7a404_drv_probe");
-
-       if (usb_disabled())
-               return -ENODEV;
-
-       ret = usb_hcd_lh7a404_probe(&ohci_lh7a404_hc_driver, pdev);
-       return ret;
-}
-
-static int ohci_hcd_lh7a404_drv_remove(struct platform_device *pdev)
-{
-       struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
-       usb_hcd_lh7a404_remove(hcd, pdev);
-       return 0;
-}
-       /*TBD*/
-/*static int ohci_hcd_lh7a404_drv_suspend(struct platform_device *dev)
-{
-       struct usb_hcd *hcd = platform_get_drvdata(dev);
-
-       return 0;
-}
-static int ohci_hcd_lh7a404_drv_resume(struct platform_device *dev)
-{
-       struct usb_hcd *hcd = platform_get_drvdata(dev);
-
-
-       return 0;
-}
-*/
-
-static struct platform_driver ohci_hcd_lh7a404_driver = {
-       .probe          = ohci_hcd_lh7a404_drv_probe,
-       .remove         = ohci_hcd_lh7a404_drv_remove,
-       .shutdown       = usb_hcd_platform_shutdown,
-       /*.suspend      = ohci_hcd_lh7a404_drv_suspend, */
-       /*.resume       = ohci_hcd_lh7a404_drv_resume, */
-       .driver         = {
-               .name   = "lh7a404-ohci",
-               .owner  = THIS_MODULE,
-       },
-};
-
-MODULE_ALIAS("platform:lh7a404-ohci");
index 51facb985c847801ca3af267aac4887293e18ad3..04812b42fe6f9d0887fe966cca3ef57b52ff9466 100644 (file)
@@ -575,18 +575,8 @@ static inline void _ohci_writel (const struct ohci_hcd *ohci,
 #endif
 }
 
-#ifdef CONFIG_ARCH_LH7A404
-/* Marc Singer: at the time this code was written, the LH7A404
- * had a problem reading the USB host registers.  This
- * implementation of the ohci_readl function performs the read
- * twice as a work-around.
- */
-#define ohci_readl(o,r)                (_ohci_readl(o,r),_ohci_readl(o,r))
-#define ohci_writel(o,v,r)     _ohci_writel(o,v,r)
-#else
 #define ohci_readl(o,r)                _ohci_readl(o,r)
 #define ohci_writel(o,v,r)     _ohci_writel(o,v,r)
-#endif
 
 
 /*-------------------------------------------------------------------------*/
index 6bafb51bb43738a415ba09547a49bef21809f9a1..b57bc273b184170304c57090ab21550a88396fdf 100644 (file)
@@ -322,69 +322,6 @@ config FB_ARMCLCD
          here and read <file:Documentation/kbuild/modules.txt>.  The module
          will be called amba-clcd.
 
-choice
-
-       depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
-       prompt "LCD Panel"
-       default FB_ARMCLCD_SHARP_LQ035Q7DB02
-
-config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
-       bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
-       help
-         This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
-         color QVGA, HRTFT panel.  The LogicPD device includes
-         an integrated HRTFT controller IC.
-         The native resolution is 240x320.
-
-config FB_ARMCLCD_SHARP_LQ057Q3DC02
-       bool "LogicPD LCD 5.7\" QVGA"
-       help
-         This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
-         color QVGA, TFT panel.  The LogicPD device includes an
-         The native resolution is 320x240.
-
-config FB_ARMCLCD_SHARP_LQ64D343
-       bool "LogicPD LCD 6.4\" VGA"
-       help
-         This is an implementation of the Sharp LQ64D343, a 6.4"
-         color VGA, TFT panel.  The LogicPD device includes an
-         The native resolution is 640x480.
-
-config FB_ARMCLCD_SHARP_LQ10D368
-       bool "LogicPD LCD 10.4\" VGA"
-       help
-         This is an implementation of the Sharp LQ10D368, a 10.4"
-         color VGA, TFT panel.  The LogicPD device includes an
-         The native resolution is 640x480.
-
-
-config FB_ARMCLCD_SHARP_LQ121S1DG41
-       bool "LogicPD LCD 12.1\" SVGA"
-       help
-         This is an implementation of the Sharp LQ121S1DG41, a 12.1"
-         color SVGA, TFT panel.  The LogicPD device includes an
-         The native resolution is 800x600.
-
-         This panel requires a clock rate may be an integer fraction
-         of the base LCDCLK frequency.  The driver will select the
-         highest frequency available that is lower than the maximum
-         allowed.  The panel may flicker if the clock rate is
-         slower than the recommended minimum.
-
-config FB_ARMCLCD_AUO_A070VW01_WIDE
-       bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
-       help
-         This is an implementation of the AU Optronics, a 7.0"
-         WIDE Color.  The native resolution is 234x480.
-
-config FB_ARMCLCD_HITACHI
-       bool "Hitachi Wide Screen 800x480"
-       help
-         This is an implementation of the Hitachi 800x480.
-
-endchoice
-
-
 config FB_ACORN
        bool "Acorn VIDC support"
        depends on (FB = y) && ARM && ARCH_ACORN