net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}

commit 87f966d97b89774162df04d2106c6350c8fe4cb3 upstream.

On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.

Cc: <netdev@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/net/ethernet/amd/pcnet32.c b/drivers/net/ethernet/amd/pcnet32.c
index ed21307276430895fadc736b16f8539afe1713cf..f6415fda103b4fbef91c1958eeee44876679fb62 100644 (file)
--- a/drivers/net/ethernet/amd/pcnet32.c
+++ b/drivers/net/ethernet/amd/pcnet32.c
@@ -1516,7 +1516,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 {
        struct pcnet32_private *lp;
        int i, media;
-       int fdx, mii, fset, dxsuflo;
+       int fdx, mii, fset, dxsuflo, sram;
        int chip_version;
        char *chipname;
        struct net_device *dev;
@@ -1553,7 +1553,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
        }
 
        /* initialize variables */
-       fdx = mii = fset = dxsuflo = 0;
+       fdx = mii = fset = dxsuflo = sram = 0;
        chip_version = (chip_version >> 12) & 0xffff;
 
        switch (chip_version) {
@@ -1586,6 +1586,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
                chipname = "PCnet/FAST III 79C973";     /* PCI */
                fdx = 1;
                mii = 1;
+               sram = 1;
                break;
        case 0x2626:
                chipname = "PCnet/Home 79C978"; /* PCI */
@@ -1609,6 +1610,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
                chipname = "PCnet/FAST III 79C975";     /* PCI */
                fdx = 1;
                mii = 1;
+               sram = 1;
                break;
        case 0x2628:
                chipname = "PCnet/PRO 79C976";
@@ -1637,6 +1639,31 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
                dxsuflo = 1;
        }
 
+       /*
+        * The Am79C973/Am79C975 controllers come with 12K of SRAM
+        * which we can use for the Tx/Rx buffers but most importantly,
+        * the use of SRAM allow us to use the BCR18:NOUFLO bit to avoid
+        * Tx fifo underflows.
+        */
+       if (sram) {
+               /*
+                * The SRAM is being configured in two steps. First we
+                * set the SRAM size in the BCR25:SRAM_SIZE bits. According
+                * to the datasheet, each bit corresponds to a 512-byte
+                * page so we can have at most 24 pages. The SRAM_SIZE
+                * holds the value of the upper 8 bits of the 16-bit SRAM size.
+                * The low 8-bits start at 0x00 and end at 0xff. So the
+                * address range is from 0x0000 up to 0x17ff. Therefore,
+                * the SRAM_SIZE is set to 0x17. The next step is to set
+                * the BCR26:SRAM_BND midway through so the Tx and Rx
+                * buffers can share the SRAM equally.
+                */
+               a->write_bcr(ioaddr, 25, 0x17);
+               a->write_bcr(ioaddr, 26, 0xc);
+               /* And finally enable the NOUFLO bit */
+               a->write_bcr(ioaddr, 18, a->read_bcr(ioaddr, 18) | (1 << 11));
+       }
+
        dev = alloc_etherdev(sizeof(*lp));
        if (!dev) {
                ret = -ENOMEM;