MIPS: Alchemy: new userspace suspend interface for development boards.
authorManuel Lauss <mano@roarinelk.homelinux.net>
Sun, 21 Dec 2008 08:26:27 +0000 (09:26 +0100)
committerRalf Baechle <ralf@linux-mips.org>
Sun, 11 Jan 2009 09:57:27 +0000 (09:57 +0000)
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.

To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:

sys/
`-- power
    `-- db1x
        |-- gpio0
        |-- gpio1
        |-- gpio2
        |-- gpio3
        |-- gpio4
        |-- gpio5
        |-- gpio6
        |-- gpio7
        |-- timer
        |-- timer_timeout
        |-- wakemsk
        `-- wakesrc

The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register.  Writing '1'
enables a wakesource, 0 disables it.

The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.

The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.

For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:

echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep

This patch also removes the homebrew CPU frequency switching code.  I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
 create mode 100644 arch/mips/alchemy/devboards/pm.c

arch/mips/alchemy/common/irq.c
arch/mips/alchemy/common/power.c
arch/mips/alchemy/devboards/Makefile
arch/mips/alchemy/devboards/pm.c [new file with mode: 0644]
arch/mips/include/asm/mach-au1x00/au1000.h

index c54384779fb91edfa81111b8aea030e2056486eb..c88c821b4c36c00398b66b8a53fcc1d75c07531f 100644 (file)
@@ -37,8 +37,6 @@
 #include <asm/mach-pb1x00/pb1000.h>
 #endif
 
-static DEFINE_SPINLOCK(irq_lock);
-
 static int au1x_ic_settype(unsigned int irq, unsigned int flow_type);
 
 /* per-processor fixed function irqs */
@@ -611,45 +609,3 @@ void __init arch_init_irq(void)
 
        set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
 }
-
-unsigned long save_local_and_disable(int controller)
-{
-       int i;
-       unsigned long flags, mask;
-
-       spin_lock_irqsave(&irq_lock, flags);
-       if (controller) {
-               mask = au_readl(IC1_MASKSET);
-               for (i = 0; i < 32; i++)
-                       au1x_ic1_mask(i + AU1000_INTC1_INT_BASE);
-       } else {
-               mask = au_readl(IC0_MASKSET);
-               for (i = 0; i < 32; i++)
-                       au1x_ic0_mask(i + AU1000_INTC0_INT_BASE);
-       }
-       spin_unlock_irqrestore(&irq_lock, flags);
-
-       return mask;
-}
-
-void restore_local_and_enable(int controller, unsigned long mask)
-{
-       int i;
-       unsigned long flags, new_mask;
-
-       spin_lock_irqsave(&irq_lock, flags);
-       for (i = 0; i < 32; i++)
-               if (mask & (1 << i)) {
-                       if (controller)
-                               au1x_ic1_unmask(i + AU1000_INTC1_INT_BASE);
-                       else
-                               au1x_ic0_unmask(i + AU1000_INTC0_INT_BASE);
-               }
-
-       if (controller)
-               new_mask = au_readl(IC1_MASKSET);
-       else
-               new_mask = au_readl(IC0_MASKSET);
-
-       spin_unlock_irqrestore(&irq_lock, flags);
-}
index f58e151b38d495a5105478b551e74ebb92b9b2a0..6ab7b42aa1be23c800bc3f07863a2991bda49762 100644 (file)
 
 #ifdef CONFIG_PM
 
-#define DEBUG 1
-#ifdef DEBUG
-#define DPRINTK(fmt, args...)  printk(KERN_DEBUG "%s: " fmt, __func__, ## args)
-#else
-#define DPRINTK(fmt, args...)
-#endif
-
-extern unsigned long save_local_and_disable(int controller);
-extern void restore_local_and_enable(int controller, unsigned long mask);
-
-static DEFINE_SPINLOCK(pm_lock);
-
 /*
  * We need to save/restore a bunch of core registers that are
  * either volatile or reset to some state across a processor sleep.
@@ -74,21 +62,6 @@ static unsigned int sleep_sys_clocks[5];
 static unsigned int sleep_sys_pinfunc;
 static unsigned int sleep_static_memctlr[4][3];
 
-/*
- * Define this to cause the value you write to /proc/sys/pm/sleep to
- * set the TOY timer for the amount of time you want to sleep.
- * This is done mainly for testing, but may be useful in other cases.
- * The value is number of 32KHz ticks to sleep.
- */
-#define SLEEP_TEST_TIMEOUT 1
-#ifdef SLEEP_TEST_TIMEOUT
-static int sleep_ticks;
-static void wakeup_counter0_set(int ticks)
-{
-       au_writel(au_readl(SYS_TOYREAD) + ticks, SYS_TOYMATCH2);
-       au_sync();
-}
-#endif
 
 static void save_core_regs(void)
 {
@@ -234,13 +207,6 @@ static void restore_core_regs(void)
 #endif
 }
 
-unsigned long suspend_mode;
-
-void wakeup_from_suspend(void)
-{
-       suspend_mode = 0;
-}
-
 void au_sleep(void)
 {
        save_core_regs();
@@ -248,279 +214,4 @@ void au_sleep(void)
        restore_core_regs();
 }
 
-static int pm_do_sleep(ctl_table *ctl, int write, struct file *file,
-                      void __user *buffer, size_t *len, loff_t *ppos)
-{
-       unsigned long wakeup, flags;
-       int ret;
-#ifdef SLEEP_TEST_TIMEOUT
-#define TMPBUFLEN2 16
-       char buf[TMPBUFLEN2], *p;
-#endif
-
-       spin_lock_irqsave(&pm_lock, flags);
-
-       if (!write) {
-               *len = 0;
-               ret = 0;
-               goto out_unlock;
-       };
-
-#ifdef SLEEP_TEST_TIMEOUT
-       if (*len > TMPBUFLEN2 - 1) {
-               ret = -EFAULT;
-               goto out_unlock;
-       }
-       if (copy_from_user(buf, buffer, *len)) {
-               return -EFAULT;
-               goto out_unlock;
-       }
-       buf[*len] = 0;
-       p = buf;
-       sleep_ticks = simple_strtoul(p, &p, 0);
-       wakeup_counter0_set(sleep_ticks);
-#endif
-
-       /**
-        ** The code below is all system dependent and we should probably
-        ** have a function call out of here to set this up.  You need
-        ** to configure the GPIO or timer interrupts that will bring
-        ** you out of sleep.
-        ** For testing, the TOY counter wakeup is useful.
-        **/
-#if 0
-       au_writel(au_readl(SYS_PINSTATERD) & ~(1 << 11), SYS_PINSTATERD);
-
-       /* GPIO 6 can cause a wake up event */
-       wakeup = au_readl(SYS_WAKEMSK);
-       wakeup &= ~(1 << 8);    /* turn off match20 wakeup */
-       wakeup |= 1 << 6;       /* turn on  GPIO  6 wakeup */
-#else
-       /* For testing, allow match20 to wake us up. */
-       wakeup = 1 << 8;        /* turn on match20 wakeup   */
-       wakeup = 0;
-#endif
-       au_writel(1, SYS_WAKESRC);      /* clear cause */
-       au_sync();
-       au_writel(wakeup, SYS_WAKEMSK);
-       au_sync();
-
-       au_sleep();
-       ret = 0;
-
-out_unlock:
-       spin_unlock_irqrestore(&pm_lock, flags);
-       return ret;
-}
-
-#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
-
-/*
- * This is right out of init/main.c
- */
-
-/*
- * This is the number of bits of precision for the loops_per_jiffy.
- * Each bit takes on average 1.5/HZ seconds.  This (like the original)
- * is a little better than 1%.
- */
-#define LPS_PREC 8
-
-static void au1000_calibrate_delay(void)
-{
-       unsigned long ticks, loopbit;
-       int lps_precision = LPS_PREC;
-
-       loops_per_jiffy = 1 << 12;
-
-       while (loops_per_jiffy <<= 1) {
-               /* Wait for "start of" clock tick */
-               ticks = jiffies;
-               while (ticks == jiffies)
-                       /* nothing */ ;
-               /* Go ... */
-               ticks = jiffies;
-               __delay(loops_per_jiffy);
-               ticks = jiffies - ticks;
-               if (ticks)
-                       break;
-       }
-
-       /*
-        * Do a binary approximation to get loops_per_jiffy set to be equal
-        * one clock (up to lps_precision bits)
-        */
-       loops_per_jiffy >>= 1;
-       loopbit = loops_per_jiffy;
-       while (lps_precision-- && (loopbit >>= 1)) {
-               loops_per_jiffy |= loopbit;
-               ticks = jiffies;
-               while (ticks == jiffies);
-               ticks = jiffies;
-               __delay(loops_per_jiffy);
-               if (jiffies != ticks)   /* longer than 1 tick */
-                       loops_per_jiffy &= ~loopbit;
-       }
-}
-
-static int pm_do_freq(ctl_table *ctl, int write, struct file *file,
-                     void __user *buffer, size_t *len, loff_t *ppos)
-{
-       int retval = 0, i;
-       unsigned long val, pll;
-#define TMPBUFLEN 64
-#define MAX_CPU_FREQ 396
-       char buf[TMPBUFLEN], *p;
-       unsigned long flags, intc0_mask, intc1_mask;
-       unsigned long old_baud_base, old_cpu_freq, old_clk, old_refresh;
-       unsigned long new_baud_base, new_cpu_freq, new_clk, new_refresh;
-       unsigned long baud_rate;
-
-       spin_lock_irqsave(&pm_lock, flags);
-       if (!write)
-               *len = 0;
-       else {
-               /* Parse the new frequency */
-               if (*len > TMPBUFLEN - 1) {
-                       spin_unlock_irqrestore(&pm_lock, flags);
-                       return -EFAULT;
-               }
-               if (copy_from_user(buf, buffer, *len)) {
-                       spin_unlock_irqrestore(&pm_lock, flags);
-                       return -EFAULT;
-               }
-               buf[*len] = 0;
-               p = buf;
-               val = simple_strtoul(p, &p, 0);
-               if (val > MAX_CPU_FREQ) {
-                       spin_unlock_irqrestore(&pm_lock, flags);
-                       return -EFAULT;
-               }
-
-               pll = val / 12;
-               if ((pll > 33) || (pll < 7)) {  /* 396 MHz max, 84 MHz min */
-                       /* Revisit this for higher speed CPUs */
-                       spin_unlock_irqrestore(&pm_lock, flags);
-                       return -EFAULT;
-               }
-
-               old_baud_base = get_au1x00_uart_baud_base();
-               old_cpu_freq = get_au1x00_speed();
-
-               new_cpu_freq = pll * 12 * 1000000;
-               new_baud_base = (new_cpu_freq / (2 * ((int)(au_readl(SYS_POWERCTRL)
-                                                           & 0x03) + 2) * 16));
-               set_au1x00_speed(new_cpu_freq);
-               set_au1x00_uart_baud_base(new_baud_base);
-
-               old_refresh = au_readl(MEM_SDREFCFG) & 0x1ffffff;
-               new_refresh = ((old_refresh * new_cpu_freq) / old_cpu_freq) |
-                             (au_readl(MEM_SDREFCFG) & ~0x1ffffff);
-
-               au_writel(pll, SYS_CPUPLL);
-               au_sync_delay(1);
-               au_writel(new_refresh, MEM_SDREFCFG);
-               au_sync_delay(1);
-
-               for (i = 0; i < 4; i++)
-                       if (au_readl(UART_BASE + UART_MOD_CNTRL +
-                                    i * 0x00100000) == 3) {
-                               old_clk = au_readl(UART_BASE + UART_CLK +
-                                                  i * 0x00100000);
-                               baud_rate = old_baud_base / old_clk;
-                               /*
-                                * We won't get an exact baud rate and the error
-                                * could be significant enough that our new
-                                * calculation will result in a clock that will
-                                * give us a baud rate that's too far off from
-                                * what we really want.
-                                */
-                               if (baud_rate > 100000)
-                                       baud_rate = 115200;
-                               else if (baud_rate > 50000)
-                                       baud_rate = 57600;
-                               else if (baud_rate > 30000)
-                                       baud_rate = 38400;
-                               else if (baud_rate > 17000)
-                                       baud_rate = 19200;
-                               else
-                                       baud_rate = 9600;
-                               new_clk = new_baud_base / baud_rate;
-                               au_writel(new_clk, UART_BASE + UART_CLK +
-                                         i * 0x00100000);
-                               au_sync_delay(10);
-                       }
-       }
-
-       /*
-        * We don't want _any_ interrupts other than match20. Otherwise our
-        * au1000_calibrate_delay() calculation will be off, potentially a lot.
-        */
-       intc0_mask = save_local_and_disable(0);
-       intc1_mask = save_local_and_disable(1);
-       val = 1 << (AU1000_TOY_MATCH2_INT - AU1000_INTC0_INT_BASE);
-       au_writel(val, IC0_MASKSET);    /* unmask */
-       au_writel(val, IC0_WAKESET);    /* enable wake-from-sleep */
-       au_sync();
-       spin_unlock_irqrestore(&pm_lock, flags);
-       au1000_calibrate_delay();
-       restore_local_and_enable(0, intc0_mask);
-       restore_local_and_enable(1, intc1_mask);
-
-       return retval;
-}
-#endif
-
-static struct ctl_table pm_table[] = {
-       {
-               .ctl_name       = CTL_UNNUMBERED,
-               .procname       = "sleep",
-               .data           = NULL,
-               .maxlen         = 0,
-               .mode           = 0600,
-               .proc_handler   = &pm_do_sleep
-       },
-#if !defined(CONFIG_SOC_AU1200) && !defined(CONFIG_SOC_AU1550)
-       {
-               .ctl_name       = CTL_UNNUMBERED,
-               .procname       = "freq",
-               .data           = NULL,
-               .maxlen         = 0,
-               .mode           = 0600,
-               .proc_handler   = &pm_do_freq
-       },
-#endif
-       {}
-};
-
-static struct ctl_table pm_dir_table[] = {
-       {
-               .ctl_name       = CTL_UNNUMBERED,
-               .procname       = "pm",
-               .mode           = 0555,
-               .child          = pm_table
-       },
-       {}
-};
-
-/*
- * Initialize power interface
- */
-static int __init pm_init(void)
-{
-       /* init TOY to tick at 1Hz. No need to wait for access bits
-        * since there's plenty of time between here and the first
-        * suspend cycle.
-        */
-       if (au_readl(SYS_TOYTRIM) != 32767) {
-               au_writel(32767, SYS_TOYTRIM);
-               au_sync();
-       }
-
-       register_sysctl_table(pm_dir_table);
-       return 0;
-}
-
-__initcall(pm_init);
-
 #endif /* CONFIG_PM */
index c0eb87a66fbd7a7db3c597b75004ca03df1a7be8..730f9f2b30e81afbd4531f7dabdacd56239fa5ab 100644 (file)
@@ -3,6 +3,7 @@
 #
 
 obj-y += prom.o
+obj-$(CONFIG_PM)               += pm.o
 obj-$(CONFIG_MIPS_PB1000)      += pb1000/
 obj-$(CONFIG_MIPS_PB1100)      += pb1100/
 obj-$(CONFIG_MIPS_PB1200)      += pb1200/
diff --git a/arch/mips/alchemy/devboards/pm.c b/arch/mips/alchemy/devboards/pm.c
new file mode 100644 (file)
index 0000000..d5eb9c3
--- /dev/null
@@ -0,0 +1,229 @@
+/*
+ * Alchemy Development Board example suspend userspace interface.
+ *
+ * (c) 2008 Manuel Lauss <mano@roarinelk.homelinux.net>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/suspend.h>
+#include <linux/sysfs.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/*
+ * Generic suspend userspace interface for Alchemy development boards.
+ * This code exports a few sysfs nodes under /sys/power/db1x/ which
+ * can be used by userspace to en/disable all au1x-provided wakeup
+ * sources and configure the timeout after which the the TOYMATCH2 irq
+ * is to trigger a wakeup.
+ */
+
+
+static unsigned long db1x_pm_sleep_secs;
+static unsigned long db1x_pm_wakemsk;
+static unsigned long db1x_pm_last_wakesrc;
+
+static int db1x_pm_enter(suspend_state_t state)
+{
+       /* enable GPIO based wakeup */
+       au_writel(1, SYS_PININPUTEN);
+
+       /* clear and setup wake cause and source */
+       au_writel(0, SYS_WAKEMSK);
+       au_sync();
+       au_writel(0, SYS_WAKESRC);
+       au_sync();
+
+       au_writel(db1x_pm_wakemsk, SYS_WAKEMSK);
+       au_sync();
+
+       /* setup 1Hz-timer-based wakeup: wait for reg access */
+       while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M20)
+               asm volatile ("nop");
+
+       au_writel(au_readl(SYS_TOYREAD) + db1x_pm_sleep_secs, SYS_TOYMATCH2);
+       au_sync();
+
+       /* wait for value to really hit the register */
+       while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M20)
+               asm volatile ("nop");
+
+       /* ...and now the sandman can come! */
+       au_sleep();
+
+       return 0;
+}
+
+static int db1x_pm_begin(suspend_state_t state)
+{
+       if (!db1x_pm_wakemsk) {
+               printk(KERN_ERR "db1x: no wakeup source activated!\n");
+               return -EINVAL;
+       }
+
+       return 0;
+}
+
+static void db1x_pm_end(void)
+{
+       /* read and store wakeup source, the clear the register. To
+        * be able to clear it, WAKEMSK must be cleared first.
+        */
+       db1x_pm_last_wakesrc = au_readl(SYS_WAKESRC);
+
+       au_writel(0, SYS_WAKEMSK);
+       au_writel(0, SYS_WAKESRC);
+       au_sync();
+
+}
+
+static struct platform_suspend_ops db1x_pm_ops = {
+       .valid          = suspend_valid_only_mem,
+       .begin          = db1x_pm_begin,
+       .enter          = db1x_pm_enter,
+       .end            = db1x_pm_end,
+};
+
+#define ATTRCMP(x) (0 == strcmp(attr->attr.name, #x))
+
+static ssize_t db1x_pmattr_show(struct kobject *kobj,
+                               struct kobj_attribute *attr,
+                               char *buf)
+{
+       int idx;
+
+       if (ATTRCMP(timer_timeout))
+               return sprintf(buf, "%lu\n", db1x_pm_sleep_secs);
+
+       else if (ATTRCMP(timer))
+               return sprintf(buf, "%u\n",
+                               !!(db1x_pm_wakemsk & SYS_WAKEMSK_M2));
+
+       else if (ATTRCMP(wakesrc))
+               return sprintf(buf, "%lu\n", db1x_pm_last_wakesrc);
+
+       else if (ATTRCMP(gpio0) || ATTRCMP(gpio1) || ATTRCMP(gpio2) ||
+                ATTRCMP(gpio3) || ATTRCMP(gpio4) || ATTRCMP(gpio5) ||
+                ATTRCMP(gpio6) || ATTRCMP(gpio7)) {
+               idx = (attr->attr.name)[4] - '0';
+               return sprintf(buf, "%d\n",
+                       !!(db1x_pm_wakemsk & SYS_WAKEMSK_GPIO(idx)));
+
+       } else if (ATTRCMP(wakemsk)) {
+               return sprintf(buf, "%08lx\n", db1x_pm_wakemsk);
+       }
+
+       return -ENOENT;
+}
+
+static ssize_t db1x_pmattr_store(struct kobject *kobj,
+                                struct kobj_attribute *attr,
+                                const char *instr,
+                                size_t bytes)
+{
+       unsigned long l;
+       int tmp;
+
+       if (ATTRCMP(timer_timeout)) {
+               tmp = strict_strtoul(instr, 0, &l);
+               if (tmp)
+                       return tmp;
+
+               db1x_pm_sleep_secs = l;
+
+       } else if (ATTRCMP(timer)) {
+               if (instr[0] != '0')
+                       db1x_pm_wakemsk |= SYS_WAKEMSK_M2;
+               else
+                       db1x_pm_wakemsk &= ~SYS_WAKEMSK_M2;
+
+       } else if (ATTRCMP(gpio0) || ATTRCMP(gpio1) || ATTRCMP(gpio2) ||
+                  ATTRCMP(gpio3) || ATTRCMP(gpio4) || ATTRCMP(gpio5) ||
+                  ATTRCMP(gpio6) || ATTRCMP(gpio7)) {
+               tmp = (attr->attr.name)[4] - '0';
+               if (instr[0] != '0') {
+                       db1x_pm_wakemsk |= SYS_WAKEMSK_GPIO(tmp);
+               } else {
+                       db1x_pm_wakemsk &= ~SYS_WAKEMSK_GPIO(tmp);
+               }
+
+       } else if (ATTRCMP(wakemsk)) {
+               tmp = strict_strtoul(instr, 0, &l);
+               if (tmp)
+                       return tmp;
+
+               db1x_pm_wakemsk = l & 0x0000003f;
+
+       } else
+               bytes = -ENOENT;
+
+       return bytes;
+}
+
+#define ATTR(x)                                                        \
+       static struct kobj_attribute x##_attribute =            \
+               __ATTR(x, 0664, db1x_pmattr_show,               \
+                               db1x_pmattr_store);
+
+ATTR(gpio0)            /* GPIO-based wakeup enable */
+ATTR(gpio1)
+ATTR(gpio2)
+ATTR(gpio3)
+ATTR(gpio4)
+ATTR(gpio5)
+ATTR(gpio6)
+ATTR(gpio7)
+ATTR(timer)            /* TOYMATCH2-based wakeup enable */
+ATTR(timer_timeout)    /* timer-based wakeup timeout value, in seconds */
+ATTR(wakesrc)          /* contents of SYS_WAKESRC after last wakeup */
+ATTR(wakemsk)          /* direct access to SYS_WAKEMSK */
+
+#define ATTR_LIST(x)   & x ## _attribute.attr
+static struct attribute *db1x_pmattrs[] = {
+       ATTR_LIST(gpio0),
+       ATTR_LIST(gpio1),
+       ATTR_LIST(gpio2),
+       ATTR_LIST(gpio3),
+       ATTR_LIST(gpio4),
+       ATTR_LIST(gpio5),
+       ATTR_LIST(gpio6),
+       ATTR_LIST(gpio7),
+       ATTR_LIST(timer),
+       ATTR_LIST(timer_timeout),
+       ATTR_LIST(wakesrc),
+       ATTR_LIST(wakemsk),
+       NULL,           /* terminator */
+};
+
+static struct attribute_group db1x_pmattr_group = {
+       .name   = "db1x",
+       .attrs  = db1x_pmattrs,
+};
+
+/*
+ * Initialize suspend interface
+ */
+static int __init pm_init(void)
+{
+       /* init TOY to tick at 1Hz if not already done. No need to wait
+        * for confirmation since there's plenty of time from here to
+        * the next suspend cycle.
+        */
+       if (au_readl(SYS_TOYTRIM) != 32767) {
+               au_writel(32767, SYS_TOYTRIM);
+               au_sync();
+       }
+
+       db1x_pm_last_wakesrc = au_readl(SYS_WAKESRC);
+
+       au_writel(0, SYS_WAKESRC);
+       au_sync();
+       au_writel(0, SYS_WAKEMSK);
+       au_sync();
+
+       suspend_set_ops(&db1x_pm_ops);
+
+       return sysfs_create_group(power_kobj, &db1x_pmattr_group);
+}
+
+late_initcall(pm_init);
index 515373c6d4a1e984d3c343811e730c1b8810f30b..62f91f50b5b59d850346ea5fbc3365fb58ace9aa 100644 (file)
@@ -1560,6 +1560,10 @@ enum soc_au1200_ints {
 #define SYS_SLPPWR             0xB1900078
 #define SYS_SLEEP              0xB190007C
 
+#define SYS_WAKEMSK_D2         (1 << 9)
+#define SYS_WAKEMSK_M2         (1 << 8)
+#define SYS_WAKEMSK_GPIO(x)    (1 << (x))
+
 /* Clock Controller */
 #define SYS_FREQCTRL0          0xB1900020
 #  define SYS_FC_FRDIV2_BIT    22