skge: changing MTU while running causes problems
authorStephen Hemminger <shemminger@linux-foundation.org>
Tue, 16 Oct 2007 19:15:50 +0000 (12:15 -0700)
committerJeff Garzik <jeff@garzik.org>
Wed, 17 Oct 2007 01:10:28 +0000 (21:10 -0400)
Rather than bring network down/up when changing MTU,
only need to impact receiver.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/skge.c

index e593585f8bf71621813aadb81a9eda35e4bcaa06..d5c10fd93bf427747574ab99d4ab944af8c491c5 100644 (file)
@@ -2544,6 +2544,15 @@ static int skge_up(struct net_device *dev)
        return err;
 }
 
+/* stop receiver */
+static void skge_rx_stop(struct skge_hw *hw, int port)
+{
+       skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
+       skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
+                    RB_RST_SET|RB_DIS_OP_MD);
+       skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+}
+
 static int skge_down(struct net_device *dev)
 {
        struct skge_port *skge = netdev_priv(dev);
@@ -2595,11 +2604,8 @@ static int skge_down(struct net_device *dev)
 
        /* Reset the RAM Buffer async Tx queue */
        skge_write8(hw, RB_ADDR(port == 0 ? Q_XA1 : Q_XA2, RB_CTRL), RB_RST_SET);
-       /* stop receiver */
-       skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
-       skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
-                    RB_RST_SET|RB_DIS_OP_MD);
-       skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+
+       skge_rx_stop(hw, port);
 
        if (hw->chip_id == CHIP_ID_GENESIS) {
                skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_SET);
@@ -2782,7 +2788,11 @@ static void skge_tx_timeout(struct net_device *dev)
 
 static int skge_change_mtu(struct net_device *dev, int new_mtu)
 {
+       struct skge_port *skge = netdev_priv(dev);
+       struct skge_hw *hw = skge->hw;
+       int port = skge->port;
        int err;
+       u16 ctl, reg;
 
        if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
                return -EINVAL;
@@ -2792,13 +2802,40 @@ static int skge_change_mtu(struct net_device *dev, int new_mtu)
                return 0;
        }
 
-       skge_down(dev);
+       skge_write32(hw, B0_IMSK, 0);
+       dev->trans_start = jiffies;     /* prevent tx timeout */
+       netif_stop_queue(dev);
+       napi_disable(&skge->napi);
+
+       ctl = gma_read16(hw, port, GM_GP_CTRL);
+       gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA);
+
+       skge_rx_clean(skge);
+       skge_rx_stop(hw, port);
 
        dev->mtu = new_mtu;
 
-       err = skge_up(dev);
+       reg = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+       if (new_mtu > 1500)
+               reg |= GM_SMOD_JUMBO_ENA;
+       gma_write16(hw, port, GM_SERIAL_MODE, reg);
+
+       skge_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD);
+
+       err = skge_rx_fill(dev);
+       wmb();
+       if (!err)
+               skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F);
+       skge_write32(hw, B0_IMSK, hw->intr_mask);
+
        if (err)
                dev_close(dev);
+       else {
+               gma_write16(hw, port, GM_GP_CTRL, ctl);
+
+               napi_enable(&skge->napi);
+               netif_wake_queue(dev);
+       }
 
        return err;
 }