--- /dev/null
+Broadcom SPI controller
+
+The Broadcom SPI controller is a SPI master found on various SOCs, including
+BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits
+of :
+ MSPI : SPI master controller can read and write to a SPI slave device
+ BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration
+ for flash reads and be configured to do single, double, quad lane
+ io with 3-byte and 4-byte addressing support.
+
+ Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP.
+ MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance
+ of a MSPI master without the BSPI to use with non flash slave devices that
+ use SPI protocol.
+
+Required properties:
+
+- #address-cells:
+ Must be <1>, as required by generic SPI binding.
+
+- #size-cells:
+ Must be <0>, also as required by generic SPI binding.
+
+- compatible:
+ Must be one of :
+ "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs
+ "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI
+ BRCMSTB SoCs
+ "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi" : MSPI+BSPI on Cygnus, NSP
+ "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi" : NS2 SoCs
+
+- reg:
+ Define the bases and ranges of the associated I/O address spaces.
+ The required range is MSPI controller registers.
+
+- reg-names:
+ First name does not matter, but must be reserved for the MSPI controller
+ register range as mentioned in 'reg' above, and will typically contain
+ - "bspi_regs": BSPI register range, not required with compatible
+ "spi-brcmstb-mspi"
+ - "mspi_regs": MSPI register range is required for compatible strings
+ - "intr_regs", "intr_status_reg" : Interrupt and status register for
+ NSP, NS2, Cygnus SoC
+
+- interrupts
+ The interrupts used by the MSPI and/or BSPI controller.
+
+- interrupt-names:
+ Names of interrupts associated with MSPI
+ - "mspi_halted" :
+ - "mspi_done": Indicates that the requested SPI operation is complete.
+ - "spi_lr_fullness_reached" : Linear read BSPI pipe full
+ - "spi_lr_session_aborted" : Linear read BSPI pipe aborted
+ - "spi_lr_impatient" : Linear read BSPI requested when pipe empty
+ - "spi_lr_session_done" : Linear read BSPI session done
+
+- clocks:
+ A phandle to the reference clock for this block.
+
+Optional properties:
+
+
+- native-endian
+ Defined when using BE SoC and device uses BE register read/write
+
+Recommended optional m25p80 properties:
+- spi-rx-bus-width: Definition as per
+ Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Examples:
+
+BRCMSTB SoC Example:
+
+ SPI Master (MSPI+BSPI) for SPI-NOR access:
+
+ spi@f03e3400 {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-qspi";
+ reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>;
+ reg-names = "cs_reg", "mspi", "bspi";
+ interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>;
+ interrupt-parent = <0x1c>;
+ interrupt-names = "mspi_halted",
+ "mspi_done",
+ "spi_lr_overread",
+ "spi_lr_session_done",
+ "spi_lr_impatient",
+ "spi_lr_session_aborted",
+ "spi_lr_fullness_reached";
+
+ clocks = <&hif_spi>;
+ clock-names = "sw_spi";
+
+ m25p80@0 {
+ #size-cells = <0x2>;
+ #address-cells = <0x2>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <0x2625a00>;
+ spi-cpol;
+ spi-cpha;
+ m25p,fast-read;
+
+ flash0.bolt@0 {
+ reg = <0x0 0x0 0x0 0x100000>;
+ };
+
+ flash0.macadr@100000 {
+ reg = <0x0 0x100000 0x0 0x10000>;
+ };
+
+ flash0.nvram@110000 {
+ reg = <0x0 0x110000 0x0 0x10000>;
+ };
+
+ flash0.kernel@120000 {
+ reg = <0x0 0x120000 0x0 0x400000>;
+ };
+
+ flash0.devtree@520000 {
+ reg = <0x0 0x520000 0x0 0x10000>;
+ };
+
+ flash0.splash@530000 {
+ reg = <0x0 0x530000 0x0 0x80000>;
+ };
+
+ flash0@0 {
+ reg = <0x0 0x0 0x0 0x4000000>;
+ };
+ };
+ };
+
+
+ MSPI master for any SPI device :
+
+ spi@f0416000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&upg_fixed>;
+ compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-mspi";
+ reg = <0xf0416000 0x180>;
+ reg-names = "mspi";
+ interrupts = <0x14>;
+ interrupt-parent = <&irq0_aon_intc>;
+ interrupt-names = "mspi_done";
+ };
+
+iProc SoC Example:
+
+ qspi: spi@18027200 {
+ compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+ reg = <0x18027200 0x184>,
+ <0x18027000 0x124>,
+ <0x1811c408 0x004>,
+ <0x180273a0 0x01c>;
+ reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg";
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names =
+ "spi_lr_fullness_reached",
+ "spi_lr_session_aborted",
+ "spi_lr_impatient",
+ "spi_lr_session_done",
+ "mspi_done",
+ "mspi_halted";
+ clocks = <&iprocmed>;
+ clock-names = "iprocmed";
+ num-cs = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+
+ NS2 SoC Example:
+
+ qspi: spi@66470200 {
+ compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi";
+ reg = <0x66470200 0x184>,
+ <0x66470000 0x124>,
+ <0x67017408 0x004>,
+ <0x664703a0 0x01c>;
+ reg-names = "mspi", "bspi", "intr_regs",
+ "intr_status_reg";
+ interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "spi_l1_intr";
+ clocks = <&iprocmed>;
+ clock-names = "iprocmed";
+ num-cs = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+
+ m25p80 node for NSP, NS2
+
+ &qspi {
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
projects / GitHub / LineageOS / G12 / android_kernel_amlogic_linux-4.9.git / commitdiff