V4L/DVB (7392): saa7134: support 2nd DVB-S section of the MD8800
authorHartmut Hackmann <hartmut.hackmann@t-online.de>
Tue, 22 Apr 2008 17:46:08 +0000 (14:46 -0300)
committerMauro Carvalho Chehab <mchehab@infradead.org>
Thu, 24 Apr 2008 17:07:52 +0000 (14:07 -0300)
There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
  so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
  14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.

Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/saa7134/saa7134-dvb.c

index a29d800616b17a09baec8f1959de910bcd731f4e..8e55c7572b4b6e252a3307684fabecc9b0bdc000 100644 (file)
@@ -33,6 +33,7 @@
 #include "saa7134.h"
 #include <media/v4l2-common.h>
 #include "dvb-pll.h"
+#include <dvb_frontend.h>
 
 #include "mt352.h"
 #include "mt352_priv.h" /* FIXME */
@@ -94,7 +95,7 @@ static int pinnacle_antenna_pwr(struct saa7134_dev *dev, int on)
        saa_setl(SAA7134_GPIO_GPSTATUS0 >> 2,   (1 << 28));
        udelay(10);
        ok = saa_readl(SAA7134_GPIO_GPSTATUS0) & (1 << 27);
-       dprintk("%s %s\n", __FUNCTION__, ok ? "on" : "off");
+       dprintk("%s %s\n", __func__, ok ? "on" : "off");
 
        if (!ok)
                saa_clearl(SAA7134_GPIO_GPSTATUS0 >> 2,   (1 << 26));
@@ -114,7 +115,7 @@ static int mt352_pinnacle_init(struct dvb_frontend* fe)
        static u8 irq_cfg []       = { INTERRUPT_EN_0, 0x00, 0x00, 0x00, 0x00 };
        struct saa7134_dev *dev= fe->dvb->priv;
 
-       dprintk("%s called\n", __FUNCTION__);
+       dprintk("%s called\n", __func__);
 
        mt352_write(fe, clock_config,   sizeof(clock_config));
        udelay(200);
@@ -882,6 +883,33 @@ static int md8800_set_high_voltage(struct dvb_frontend *fe, long arg)
        return res;
 };
 
+static int md8800_set_voltage2(struct dvb_frontend *fe, fe_sec_voltage_t voltage)
+{
+       struct saa7134_dev *dev = fe->dvb->priv;
+       u8 wbuf[2] = { 0x1f, 00 };
+       u8 rbuf;
+       struct i2c_msg msg[] = { { .addr = 0x08, .flags = 0, .buf = wbuf, .len = 1 },
+                                { .addr = 0x08, .flags = I2C_M_RD, .buf = &rbuf, .len = 1 } };
+
+       if (i2c_transfer(&dev->i2c_adap, msg, 2) != 2)
+               return -EIO;
+       /* NOTE: this assumes that gpo1 is used, it might be bit 5 (gpo2) */
+       if (voltage == SEC_VOLTAGE_18)
+               wbuf[1] = rbuf | 0x10;
+       else
+               wbuf[1] = rbuf & 0xef;
+       msg[0].len = 2;
+       i2c_transfer(&dev->i2c_adap, msg, 1);
+       return 0;
+}
+
+static int md8800_set_high_voltage2(struct dvb_frontend *fe, long arg)
+{
+       struct saa7134_dev *dev = fe->dvb->priv;
+       wprintk("%s: sorry can't set high LNB supply voltage from here\n", __func__);
+       return -EIO;
+}
+
 /* ==================================================================
  * nxt200x based ATSC cards, helper functions
  */
@@ -1003,11 +1031,11 @@ static int dvb_init(struct saa7134_dev *dev)
                        if (dev->dvb.frontend) {
                                if (dvb_attach(tda826x_attach, dev->dvb.frontend, 0x63,
                                                                        &dev->i2c_adap, 0) == NULL) {
-                                       wprintk("%s: Lifeview Trio, No tda826x found!\n", __FUNCTION__);
+                                       wprintk("%s: Lifeview Trio, No tda826x found!\n", __func__);
                                }
                                if (dvb_attach(isl6421_attach, dev->dvb.frontend, &dev->i2c_adap,
                                                                                0x08, 0, 0) == NULL) {
-                                       wprintk("%s: Lifeview Trio, No ISL6421 found!\n", __FUNCTION__);
+                                       wprintk("%s: Lifeview Trio, No ISL6421 found!\n", __func__);
                                }
                        }
                }
@@ -1036,27 +1064,35 @@ static int dvb_init(struct saa7134_dev *dev)
                        dev->dvb.frontend = dvb_attach(tda10086_attach,
                                                        &flydvbs, &dev->i2c_adap);
                        if (dev->dvb.frontend) {
-                               struct dvb_frontend *fe;
+                               struct dvb_frontend *fe = dev->dvb.frontend;
+                               u8 dev_id = dev->eedata[2];
+                               u8 data = 0xc4;
+                               struct i2c_msg msg = {.addr = 0x08, .flags = 0, .len = 1};
+
                                if (dvb_attach(tda826x_attach, dev->dvb.frontend,
                                                0x60, &dev->i2c_adap, 0) == NULL)
                                        wprintk("%s: Medion Quadro, no tda826x "
-                                               "found !\n", __FUNCTION__);
-                               /* Note 10.2. Hac
-                                * up to here. configuration for ctx948 and and one branch
-                                * of md8800 should be identical
-                                */
-                               /* we need to open the i2c gate (we know it exists) */
-                               fe = dev->dvb.frontend;
-                               fe->ops.i2c_gate_ctrl(fe, 1);
-                               if (dvb_attach(isl6405_attach, fe,
-                                               &dev->i2c_adap, 0x08, 0, 0) == NULL)
-                                       wprintk("%s: Medion Quadro, no ISL6405 "
-                                               "found !\n", __FUNCTION__);
-                               fe->ops.i2c_gate_ctrl(fe, 0);
-                               dev->original_set_voltage = fe->ops.set_voltage;
-                               fe->ops.set_voltage = md8800_set_voltage;
-                               dev->original_set_high_voltage = fe->ops.enable_high_lnb_voltage;
-                               fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage;
+                                               "found !\n", __func__);
+                               if (dev_id != 0x08) {
+                                       /* we need to open the i2c gate (we know it exists) */
+                                       fe->ops.i2c_gate_ctrl(fe, 1);
+                                       if (dvb_attach(isl6405_attach, fe,
+                                                       &dev->i2c_adap, 0x08, 0, 0) == NULL)
+                                               wprintk("%s: Medion Quadro, no ISL6405 "
+                                                       "found !\n", __func__);
+                                       /* fire up the 2nd section of the LNB supply since we can't do
+                                       this from the other section */
+                                       msg.buf = &data;
+                                       i2c_transfer(&dev->i2c_adap, &msg, 1);
+                                       fe->ops.i2c_gate_ctrl(fe, 0);
+                                       dev->original_set_voltage = fe->ops.set_voltage;
+                                       fe->ops.set_voltage = md8800_set_voltage;
+                                       dev->original_set_high_voltage = fe->ops.enable_high_lnb_voltage;
+                                       fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage;
+                               } else {
+                                       fe->ops.set_voltage = md8800_set_voltage2;
+                                       fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage2;
+                               }
                        }
                }
                break;
@@ -1082,11 +1118,11 @@ static int dvb_init(struct saa7134_dev *dev)
                if (dev->dvb.frontend) {
                        if (dvb_attach(tda826x_attach, dev->dvb.frontend, 0x60,
                                       &dev->i2c_adap, 0) == NULL) {
-                               wprintk("%s: No tda826x found!\n", __FUNCTION__);
+                               wprintk("%s: No tda826x found!\n", __func__);
                        }
                        if (dvb_attach(isl6421_attach, dev->dvb.frontend,
                                       &dev->i2c_adap, 0x08, 0, 0) == NULL) {
-                               wprintk("%s: No ISL6421 found!\n", __FUNCTION__);
+                               wprintk("%s: No ISL6421 found!\n", __func__);
                        }
                }
                break;
@@ -1138,10 +1174,10 @@ static int dvb_init(struct saa7134_dev *dev)
                if (dev->dvb.frontend) {
                        if (dvb_attach(tda826x_attach, dev->dvb.frontend, 0x60,
                                        &dev->i2c_adap, 0) == NULL)
-                               wprintk("%s: No tda826x found!\n", __FUNCTION__);
+                               wprintk("%s: No tda826x found!\n", __func__);
                        if (dvb_attach(lnbp21_attach, dev->dvb.frontend,
                                        &dev->i2c_adap, 0, 0) == NULL)
-                               wprintk("%s: No lnbp21 found!\n", __FUNCTION__);
+                               wprintk("%s: No lnbp21 found!\n", __func__);
                }
                break;
        case SAA7134_BOARD_CREATIX_CTX953:
@@ -1164,14 +1200,14 @@ static int dvb_init(struct saa7134_dev *dev)
                        if (dvb_attach(dvb_pll_attach, dev->dvb.frontend, 0x60,
                                  &dev->i2c_adap, DVB_PLL_PHILIPS_SD1878_TDA8261) == NULL)
                                wprintk("%s: MD7134 DVB-S, no SD1878 "
-                                       "found !\n", __FUNCTION__);
+                                       "found !\n", __func__);
                        /* we need to open the i2c gate (we know it exists) */
                        fe = dev->dvb.frontend;
                        fe->ops.i2c_gate_ctrl(fe, 1);
                        if (dvb_attach(isl6405_attach, fe,
                                        &dev->i2c_adap, 0x08, 0, 0) == NULL)
                                wprintk("%s: MD7134 DVB-S, no ISL6405 "
-                                       "found !\n", __FUNCTION__);
+                                       "found !\n", __func__);
                        fe->ops.i2c_gate_ctrl(fe, 0);
                        dev->original_set_voltage = fe->ops.set_voltage;
                        fe->ops.set_voltage = md8800_set_voltage;
@@ -1239,8 +1275,20 @@ static int dvb_fini(struct saa7134_dev *dev)
 
                /* otherwise we don't detect the tuner on next insmod */
                saa7134_i2c_call_clients(dev, TUNER_SET_CONFIG, &tda9887_cfg);
+       } else if (dev->board == SAA7134_BOARD_MEDION_MD8800_QUADRO) {
+               if ((dev->eedata[2] != 0x08) && use_frontend) {
+                       /* turn off the 2nd lnb supply */
+                       u8 data = 0x80;
+                       struct i2c_msg msg = {.addr = 0x08, .buf = &data, .flags = 0, .len = 1};
+                       struct dvb_frontend *fe;
+                       fe = dev->dvb.frontend;
+                       if (fe->ops.i2c_gate_ctrl) {
+                               fe->ops.i2c_gate_ctrl(fe, 1);
+                               i2c_transfer(&dev->i2c_adap, &msg, 1);
+                               fe->ops.i2c_gate_ctrl(fe, 0);
+                       }
+               }
        }
-
        videobuf_dvb_unregister(&dev->dvb);
        return 0;
 }