3c59x: convert to net_device_ops
authorStephen Hemminger <shemminger@linux-foundation.org>
Fri, 9 Jan 2009 13:01:18 +0000 (13:01 +0000)
committerDavid S. Miller <davem@davemloft.net>
Wed, 21 Jan 2009 22:02:25 +0000 (14:02 -0800)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/3c59x.c

index cdbbb6226fc598d3fd5bb5b072fd5ffba7ef1c9d..b2563d384cf2998a8b763cf9767146716b718b86 100644 (file)
@@ -992,6 +992,42 @@ out:
        return rc;
 }
 
+static const struct net_device_ops boomrang_netdev_ops = {
+       .ndo_open               = vortex_open,
+       .ndo_stop               = vortex_close,
+       .ndo_start_xmit         = boomerang_start_xmit,
+       .ndo_tx_timeout         = vortex_tx_timeout,
+       .ndo_get_stats          = vortex_get_stats,
+#ifdef CONFIG_PCI
+       .ndo_do_ioctl           = vortex_ioctl,
+#endif
+       .ndo_set_multicast_list = set_rx_mode,
+       .ndo_change_mtu         = eth_change_mtu,
+       .ndo_set_mac_address    = eth_mac_addr,
+       .ndo_validate_addr      = eth_validate_addr,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = poll_vortex,
+#endif
+};
+
+static const struct net_device_ops vortex_netdev_ops = {
+       .ndo_open               = vortex_open,
+       .ndo_stop               = vortex_close,
+       .ndo_start_xmit         = vortex_start_xmit,
+       .ndo_tx_timeout         = vortex_tx_timeout,
+       .ndo_get_stats          = vortex_get_stats,
+#ifdef CONFIG_PCI
+       .ndo_do_ioctl           = vortex_ioctl,
+#endif
+       .ndo_set_multicast_list = set_rx_mode,
+       .ndo_change_mtu         = eth_change_mtu,
+       .ndo_set_mac_address    = eth_mac_addr,
+       .ndo_validate_addr      = eth_validate_addr,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = poll_vortex,
+#endif
+};
+
 /*
  * Start up the PCI/EISA device which is described by *gendev.
  * Return 0 on success.
@@ -1366,18 +1402,16 @@ static int __devinit vortex_probe1(struct device *gendev,
        }
 
        /* The 3c59x-specific entries in the device structure. */
-       dev->open = vortex_open;
        if (vp->full_bus_master_tx) {
-               dev->hard_start_xmit = boomerang_start_xmit;
+               dev->netdev_ops = &boomrang_netdev_ops;
                /* Actually, it still should work with iommu. */
                if (card_idx < MAX_UNITS &&
                    ((hw_checksums[card_idx] == -1 && (vp->drv_flags & HAS_HWCKSM)) ||
                                hw_checksums[card_idx] == 1)) {
                        dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
                }
-       } else {
-               dev->hard_start_xmit = vortex_start_xmit;
-       }
+       } else
+               dev->netdev_ops =  &vortex_netdev_ops;
 
        if (print_info) {
                printk(KERN_INFO "%s: scatter/gather %sabled. h/w checksums %sabled\n",
@@ -1386,18 +1420,9 @@ static int __devinit vortex_probe1(struct device *gendev,
                                (dev->features & NETIF_F_IP_CSUM) ? "en":"dis");
        }
 
-       dev->stop = vortex_close;
-       dev->get_stats = vortex_get_stats;
-#ifdef CONFIG_PCI
-       dev->do_ioctl = vortex_ioctl;
-#endif
        dev->ethtool_ops = &vortex_ethtool_ops;
-       dev->set_multicast_list = set_rx_mode;
-       dev->tx_timeout = vortex_tx_timeout;
        dev->watchdog_timeo = (watchdog * HZ) / 1000;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       dev->poll_controller = poll_vortex;
-#endif
+
        if (pdev) {
                vp->pm_state_valid = 1;
                pci_save_state(VORTEX_PCI(vp));