'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
The driver supports multiple bonding modes to allow for both high
- perfomance and high availability operation.
+ performance and high availability operation.
Refer to <file:Documentation/networking/bonding.txt> for more
information.
depends on NET_VENDOR_3COM && (PCI || EISA)
select MII
---help---
- This option enables driver support for a large number of 10mbps and
- 10/100mbps EISA, PCI and PCMCIA 3Com network cards:
+ This option enables driver support for a large number of 10Mbps and
+ 10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
"Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
"Boomerang" (EtherLink XL 3c900 or 3c905) PCI
depends on NET_ISA
---help---
If you have a network (Ethernet) card of this type, say Y. This
- driver supports intel i82595{FX,TX} based boards. Note however
+ driver supports Intel i82595{FX,TX} based boards. Note however
that the EtherExpress PRO/100 Ethernet card has its own separate
driver. Please read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
help
Additional receive skb headroom. Note, that driver
will always reserve at least 2 bytes to make IP header
- aligned, so usualy there is no need to add any additional
+ aligned, so usually there is no need to add any additional
headroom.
If unsure, set to 0.
will be called myri_sbus. This is recommended.
config NS83820
- tristate "National Semiconduct DP83820 support"
+ tristate "National Semiconductor DP83820 support"
depends on PCI
help
This is a driver for the National Semiconductor DP83820 series
Say Y here if you want to be able to filter the packets passing over
PPP interfaces. This allows you to control which packets count as
activity (i.e. which packets will reset the idle timer or bring up
- a demand-dialled link) and which packets are to be dropped entirely.
+ a demand-dialed link) and which packets are to be dropped entirely.
You need to say Y here if you wish to use the pass-filter and
active-filter options to pppd.
<file:Documentation/networking/shaper.txt> for more information.
An alternative to this traffic shaper is the experimental
- Class-Based Queueing (CBQ) scheduling support which you get if you
- say Y to "QoS and/or fair queueing" above.
+ Class-Based Queuing (CBQ) scheduling support which you get if you
+ say Y to "QoS and/or fair queuing" above.
To compile this driver as a module, choose M here: the module
will be called shaper. If unsure, say N.
packet is stuffed with an extra 4 byte "cookie" which doesn't
actually appear on the network. After transmit the driver will send
back a packet with protocol byte 0 containing the status of the
- transmition:
+ transmission:
0=no hardware acknowledge
1=excessive nak
- 2=transmition accepted by the reciever hardware
+ 2=transmission accepted by the receiver hardware
Received packets are also stuffed with the extra 4 bytes but it will
be random data.
Say Y here if you want to build support for the USB IrDA FIR Dongle
device driver. To compile it as a module, choose M here: the module
will be called irda-usb. IrDA-USB support the various IrDA USB
- dongles available and most of their pecularities. Those dongles
+ dongles available and most of their peculiarities. Those dongles
plug in the USB port of your computer, are plug and play, and
support SIR and FIR (4Mbps) speeds. On the other hand, those
dongles tend to be less efficient than a FIR chipset.
help
Say Y here if you want to build support for the ALi M5123 FIR
Controller. The ALi M5123 FIR Controller is embedded in ALi M1543C,
- M1535, M1535D, M1535+, M1535D Sourth Bridge. This driver supports
+ M1535, M1535D, M1535+, M1535D South Bridge. This driver supports
SIR, MIR and FIR (4Mbps) speeds.
To compile it as a module, choose M here: the module will be called
bool "WANPIPE Frame Relay support"
depends on VENDOR_SANGOMA
help
- Connect a WANPIPE card to a Frame Relay network, or use Frame Felay
+ Connect a WANPIPE card to a Frame Relay network, or use Frame Relay
API to develop custom applications.
Contains the Ethernet Bridging over Frame Relay feature, where
In order to use this driver, you will need a firmware image for it.
You can obtain the firmware from
<http://ipw2200.sf.net/>. See the above referenced README.ipw2200
- for information on where to install the firmare images.
+ for information on where to install the firmware images.
You will also very likely need the Wireless Tools in order to
configure your card:
PCI 802.11 wireless cards.
It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
- with or without encryption) as well as card before the Cisco
- aquisition (Aironet 4500, Aironet 4800, Aironet 4800B).
+ acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).
This driver support both the standard Linux Wireless Extensions
and Cisco proprietary API, so both the Linux Wireless Tools and the
driver part of the Linux Pcmcia package.
It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
- with or without encryption) as well as card before the Cisco
- aquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
+ acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
802.11b cards.
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff