#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
#define BLINK_HZ (HZ/4)
-#define LINK_POLL_HZ (HZ/10)
MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
static void yukon_reset(struct skge_hw *hw, int port);
static void genesis_mac_init(struct skge_hw *hw, int port);
static void genesis_reset(struct skge_hw *hw, int port);
+static void genesis_link_up(struct skge_port *skge);
static const int txqaddr[] = { Q_XA1, Q_XA2 };
static const int rxqaddr[] = { Q_R1, Q_R2 };
static void genesis_reset(struct skge_hw *hw, int port)
{
- int i;
- u64 zero = 0;
+ const u8 zero[8] = { 0 };
/* reset the statistics module */
xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
/* disable Broadcom PHY IRQ */
xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
- xm_outhash(hw, port, XM_HSM, (u8 *) &zero);
- for (i = 0; i < 15; i++)
- xm_outaddr(hw, port, XM_EXM(i), (u8 *) &zero);
- xm_outhash(hw, port, XM_SRC_CHK, (u8 *) &zero);
+ xm_outhash(hw, port, XM_HSM, zero);
}
-static void genesis_mac_init(struct skge_hw *hw, int port)
+/* Convert mode to MII values */
+static const u16 phy_pause_map[] = {
+ [FLOW_MODE_NONE] = 0,
+ [FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM,
+ [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
+ [FLOW_MODE_REM_SEND] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+};
+
+
+/* Check status of Broadcom phy link */
+static void bcom_check_link(struct skge_hw *hw, int port)
{
- struct skge_port *skge = netdev_priv(hw->dev[port]);
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u16 status;
+
+ /* read twice because of latch */
+ (void) xm_phy_read(hw, port, PHY_BCOM_STAT);
+ status = xm_phy_read(hw, port, PHY_BCOM_STAT);
+
+ pr_debug("bcom_check_link status=0x%x\n", status);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ u16 cmd = xm_read16(hw, port, XM_MMU_CMD);
+ cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ xm_write16(hw, port, XM_MMU_CMD, cmd);
+ /* dummy read to ensure writing */
+ (void) xm_read16(hw, port, XM_MMU_CMD);
+
+ if (netif_carrier_ok(dev))
+ skge_link_down(skge);
+ } else {
+ if (skge->autoneg == AUTONEG_ENABLE &&
+ (status & PHY_ST_AN_OVER)) {
+ u16 lpa = xm_phy_read(hw, port, PHY_BCOM_AUNE_LP);
+ u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
+
+ if (lpa & PHY_B_AN_RF) {
+ printk(KERN_NOTICE PFX "%s: remote fault\n",
+ dev->name);
+ return;
+ }
+
+ /* Check Duplex mismatch */
+ switch(aux & PHY_B_AS_AN_RES_MSK) {
+ case PHY_B_RES_1000FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_B_RES_1000HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+ dev->name);
+ return;
+ }
+
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (aux & PHY_B_AS_PAUSE_MSK) {
+ case PHY_B_AS_PAUSE_MSK:
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ break;
+ case PHY_B_AS_PRR:
+ skge->flow_control = FLOW_MODE_REM_SEND;
+ break;
+ case PHY_B_AS_PRT:
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ break;
+ default:
+ skge->flow_control = FLOW_MODE_NONE;
+ }
+
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+ }
+}
+
+/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional
+ * Phy on for 100 or 10Mbit operation
+ */
+static void bcom_phy_init(struct skge_port *skge, int jumbo)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
int i;
- u32 r;
- u16 id1;
- u16 ctrl1, ctrl2, ctrl3, ctrl4, ctrl5;
+ u16 id1, r, ext, ctl;
/* magic workaround patterns for Broadcom */
static const struct {
{ 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
};
+ pr_debug("bcom_phy_init\n");
+
+ /* read Id from external PHY (all have the same address) */
+ id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+
+ /* Optimize MDIO transfer by suppressing preamble. */
+ r = xm_read16(hw, port, XM_MMU_CMD);
+ r |= XM_MMU_NO_PRE;
+ xm_write16(hw, port, XM_MMU_CMD,r);
+
+ switch(id1) {
+ case PHY_BCOM_ID1_C0:
+ /*
+ * Workaround BCOM Errata for the C0 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(C0hack); i++)
+ xm_phy_write(hw, port,
+ C0hack[i].reg, C0hack[i].val);
+
+ break;
+ case PHY_BCOM_ID1_A1:
+ /*
+ * Workaround BCOM Errata for the A1 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(A1hack); i++)
+ xm_phy_write(hw, port,
+ A1hack[i].reg, A1hack[i].val);
+ break;
+ }
+
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom PHYs.
+ * Disable Power Management after reset.
+ */
+ r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
+ r |= PHY_B_AC_DIS_PM;
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r);
+
+ /* Dummy read */
+ xm_read16(hw, port, XM_ISRC);
+
+ ext = PHY_B_PEC_EN_LTR; /* enable tx led */
+ ctl = PHY_CT_SP1000; /* always 1000mbit */
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ /*
+ * Workaround BCOM Errata #1 for the C5 type.
+ * 1000Base-T Link Acquisition Failure in Slave Mode
+ * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
+ */
+ u16 adv = PHY_B_1000C_RD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_B_1000C_AHD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_B_1000C_AFD;
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, adv);
+
+ ctl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ if (skge->duplex == DUPLEX_FULL)
+ ctl |= PHY_CT_DUP_MD;
+ /* Force to slave */
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, PHY_B_1000C_MSE);
+ }
+
+ /* Set autonegotiation pause parameters */
+ xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV,
+ phy_pause_map[skge->flow_control] | PHY_AN_CSMA);
+
+ /* Handle Jumbo frames */
+ if (jumbo) {
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK);
+
+ ext |= PHY_B_PEC_HIGH_LA;
+
+ }
+
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext);
+ xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl);
+
+ /* Use link status change interrrupt */
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+
+ bcom_check_link(hw, port);
+}
+
+static void genesis_mac_init(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ int jumbo = hw->dev[port]->mtu > ETH_DATA_LEN;
+ int i;
+ u32 r;
+ const u8 zero[6] = { 0 };
+
+ /* Clear MIB counters */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+ /* Clear two times according to Errata #3 */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
/* initialize Rx, Tx and Link LED */
skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
* GMII mode.
*/
spin_lock_bh(&hw->phy_lock);
-
- /* External Phy Handling */
- /* Take PHY out of reset. */
+ /* Take external Phy out of reset */
r = skge_read32(hw, B2_GP_IO);
if (port == 0)
r |= GP_DIR_0|GP_IO_0;
skge_write32(hw, B2_GP_IO, r);
skge_read32(hw, B2_GP_IO);
+ spin_unlock_bh(&hw->phy_lock);
- /* Enable GMII mode on the XMAC. */
+ /* Enable GMII interfac */
xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
- id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+ bcom_phy_init(skge, jumbo);
- /* Optimize MDIO transfer by suppressing preamble. */
- xm_write16(hw, port, XM_MMU_CMD,
- xm_read16(hw, port, XM_MMU_CMD)
- | XM_MMU_NO_PRE);
+ /* Set Station Address */
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
- if (id1 == PHY_BCOM_ID1_C0) {
- /*
- * Workaround BCOM Errata for the C0 type.
- * Write magic patterns to reserved registers.
- */
- for (i = 0; i < ARRAY_SIZE(C0hack); i++)
- xm_phy_write(hw, port,
- C0hack[i].reg, C0hack[i].val);
+ /* We don't use match addresses so clear */
+ for (i = 1; i < 16; i++)
+ xm_outaddr(hw, port, XM_EXM(i), zero);
+
+ /* configure Rx High Water Mark (XM_RX_HI_WM) */
+ xm_write16(hw, port, XM_RX_HI_WM, 1450);
+
+ /* We don't need the FCS appended to the packet. */
+ r = XM_RX_LENERR_OK | XM_RX_STRIP_FCS;
+ if (jumbo)
+ r |= XM_RX_BIG_PK_OK;
- } else if (id1 == PHY_BCOM_ID1_A1) {
+ if (skge->duplex == DUPLEX_HALF) {
/*
- * Workaround BCOM Errata for the A1 type.
- * Write magic patterns to reserved registers.
+ * If in manual half duplex mode the other side might be in
+ * full duplex mode, so ignore if a carrier extension is not seen
+ * on frames received
*/
- for (i = 0; i < ARRAY_SIZE(A1hack); i++)
- xm_phy_write(hw, port,
- A1hack[i].reg, A1hack[i].val);
+ r |= XM_RX_DIS_CEXT;
}
+ xm_write16(hw, port, XM_RX_CMD, r);
- /*
- * Workaround BCOM Errata (#10523) for all BCom PHYs.
- * Disable Power Management after reset.
- */
- r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
- xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r | PHY_B_AC_DIS_PM);
-
-
- /* Dummy read */
- xm_read16(hw, port, XM_ISRC);
-
- r = xm_read32(hw, port, XM_MODE);
- xm_write32(hw, port, XM_MODE, r|XM_MD_CSA);
-
- /* We don't need the FCS appended to the packet. */
- r = xm_read16(hw, port, XM_RX_CMD);
- xm_write16(hw, port, XM_RX_CMD, r | XM_RX_STRIP_FCS);
/* We want short frames padded to 60 bytes. */
- r = xm_read16(hw, port, XM_TX_CMD);
- xm_write16(hw, port, XM_TX_CMD, r | XM_TX_AUTO_PAD);
+ xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD);
+
+ /*
+ * Bump up the transmit threshold. This helps hold off transmit
+ * underruns when we're blasting traffic from both ports at once.
+ */
+ xm_write16(hw, port, XM_TX_THR, 512);
/*
* Enable the reception of all error frames. This is is
* case the XMAC will start transfering frames out of the
* RX FIFO as soon as the FIFO threshold is reached.
*/
- r = xm_read32(hw, port, XM_MODE);
- xm_write32(hw, port, XM_MODE,
- XM_MD_RX_CRCE|XM_MD_RX_LONG|XM_MD_RX_RUNT|
- XM_MD_RX_ERR|XM_MD_RX_IRLE);
+ xm_write32(hw, port, XM_MODE, XM_DEF_MODE);
- xm_outaddr(hw, port, XM_SA, hw->dev[port]->dev_addr);
- xm_outaddr(hw, port, XM_EXM(0), hw->dev[port]->dev_addr);
/*
- * Bump up the transmit threshold. This helps hold off transmit
- * underruns when we're blasting traffic from both ports at once.
+ * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK)
+ * - Enable all bits excepting 'Octets Rx OK Low CntOv'
+ * and 'Octets Rx OK Hi Cnt Ov'.
*/
- xm_write16(hw, port, XM_TX_THR, 512);
+ xm_write32(hw, port, XM_RX_EV_MSK, XMR_DEF_MSK);
+
+ /*
+ * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK)
+ * - Enable all bits excepting 'Octets Tx OK Low CntOv'
+ * and 'Octets Tx OK Hi Cnt Ov'.
+ */
+ xm_write32(hw, port, XM_TX_EV_MSK, XMT_DEF_MSK);
/* Configure MAC arbiter */
skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF);
skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD);
- if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+ if (jumbo) {
/* Enable frame flushing if jumbo frames used */
skge_write16(hw, SK_REG(port,RX_MFF_CTRL1), MFF_ENA_FLUSH);
} else {
/* enable timeout timers if normal frames */
skge_write16(hw, B3_PA_CTRL,
- port == 0 ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
+ (port == 0) ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
}
-
-
- r = xm_read16(hw, port, XM_RX_CMD);
- if (hw->dev[port]->mtu > ETH_DATA_LEN)
- xm_write16(hw, port, XM_RX_CMD, r | XM_RX_BIG_PK_OK);
- else
- xm_write16(hw, port, XM_RX_CMD, r & ~(XM_RX_BIG_PK_OK));
-
- /* Broadcom phy initialization */
- ctrl1 = PHY_CT_SP1000;
- ctrl2 = 0;
- ctrl3 = PHY_AN_CSMA;
- ctrl4 = PHY_B_PEC_EN_LTR;
- ctrl5 = PHY_B_AC_TX_TST;
-
- if (skge->autoneg == AUTONEG_ENABLE) {
- /*
- * Workaround BCOM Errata #1 for the C5 type.
- * 1000Base-T Link Acquisition Failure in Slave Mode
- * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
- */
- ctrl2 |= PHY_B_1000C_RD;
- if (skge->advertising & ADVERTISED_1000baseT_Half)
- ctrl2 |= PHY_B_1000C_AHD;
- if (skge->advertising & ADVERTISED_1000baseT_Full)
- ctrl2 |= PHY_B_1000C_AFD;
-
- /* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- ctrl3 |= PHY_B_P_NO_PAUSE;
- break;
- case FLOW_MODE_LOC_SEND:
- ctrl3 |= PHY_B_P_ASYM_MD;
- break;
- case FLOW_MODE_SYMMETRIC:
- ctrl3 |= PHY_B_P_SYM_MD;
- break;
- case FLOW_MODE_REM_SEND:
- ctrl3 |= PHY_B_P_BOTH_MD;
- break;
- }
-
- /* Restart Auto-negotiation */
- ctrl1 |= PHY_CT_ANE | PHY_CT_RE_CFG;
- } else {
- if (skge->duplex == DUPLEX_FULL)
- ctrl1 |= PHY_CT_DUP_MD;
-
- ctrl2 |= PHY_B_1000C_MSE; /* set it to Slave */
- }
-
- xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, ctrl2);
- xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV, ctrl3);
-
- if (skge->netdev->mtu > ETH_DATA_LEN) {
- ctrl4 |= PHY_B_PEC_HIGH_LA;
- ctrl5 |= PHY_B_AC_LONG_PACK;
-
- xm_phy_write(hw, port,PHY_BCOM_AUX_CTRL, ctrl5);
- }
-
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ctrl4);
- xm_phy_write(hw, port, PHY_BCOM_CTRL, ctrl1);
- spin_unlock_bh(&hw->phy_lock);
-
- /* Clear MIB counters */
- xm_write16(hw, port, XM_STAT_CMD,
- XM_SC_CLR_RXC | XM_SC_CLR_TXC);
- /* Clear two times according to Errata #3 */
- xm_write16(hw, port, XM_STAT_CMD,
- XM_SC_CLR_RXC | XM_SC_CLR_TXC);
-
- /* Start polling for link status */
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
}
static void genesis_stop(struct skge_port *skge)
return gma_read16(hw, port, GM_SMI_DATA);
}
-static void genesis_link_down(struct skge_port *skge)
-{
- struct skge_hw *hw = skge->hw;
- int port = skge->port;
-
- pr_debug("genesis_link_down\n");
-
- xm_write16(hw, port, XM_MMU_CMD,
- xm_read16(hw, port, XM_MMU_CMD)
- & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
-
- /* dummy read to ensure writing */
- (void) xm_read16(hw, port, XM_MMU_CMD);
-
- skge_link_down(skge);
-}
-
static void genesis_link_up(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
}
-static void genesis_bcom_intr(struct skge_port *skge)
+static inline void bcom_phy_intr(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- u16 stat = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+ u16 isrc;
+
+ isrc = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+ pr_debug("bcom_phy_interrupt status=0x%x\n", isrc);
- pr_debug("genesis_bcom intr stat=%x\n", stat);
+ if (isrc & PHY_B_IS_PSE)
+ printk(KERN_ERR PFX "%s: uncorrectable pair swap error\n",
+ hw->dev[port]->name);
/* Workaround BCom Errata:
* enable and disable loopback mode if "NO HCD" occurs.
*/
- if (stat & PHY_B_IS_NO_HDCL) {
+ if (isrc & PHY_B_IS_NO_HDCL) {
u16 ctrl = xm_phy_read(hw, port, PHY_BCOM_CTRL);
xm_phy_write(hw, port, PHY_BCOM_CTRL,
ctrl | PHY_CT_LOOP);
ctrl & ~PHY_CT_LOOP);
}
- stat = xm_phy_read(hw, port, PHY_BCOM_STAT);
- if (stat & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) {
- u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
- if ( !(aux & PHY_B_AS_LS) && netif_carrier_ok(skge->netdev))
- genesis_link_down(skge);
-
- else if (stat & PHY_B_IS_LST_CHANGE) {
- if (aux & PHY_B_AS_AN_C) {
- switch (aux & PHY_B_AS_AN_RES_MSK) {
- case PHY_B_RES_1000FD:
- skge->duplex = DUPLEX_FULL;
- break;
- case PHY_B_RES_1000HD:
- skge->duplex = DUPLEX_HALF;
- break;
- }
-
- switch (aux & PHY_B_AS_PAUSE_MSK) {
- case PHY_B_AS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- break;
- case PHY_B_AS_PRR:
- skge->flow_control = FLOW_MODE_REM_SEND;
- break;
- case PHY_B_AS_PRT:
- skge->flow_control = FLOW_MODE_LOC_SEND;
- break;
- default:
- skge->flow_control = FLOW_MODE_NONE;
- }
- skge->speed = SPEED_1000;
- }
- genesis_link_up(skge);
- }
- else
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
- }
-}
-
-/* Perodic poll of phy status to check for link transistion */
-static void skge_link_timer(unsigned long __arg)
-{
- struct skge_port *skge = (struct skge_port *) __arg;
- struct skge_hw *hw = skge->hw;
-
- if (hw->chip_id != CHIP_ID_GENESIS || !netif_running(skge->netdev))
- return;
+ if (isrc & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+ bcom_check_link(hw, port);
- spin_lock_bh(&hw->phy_lock);
- genesis_bcom_intr(skge);
- spin_unlock_bh(&hw->phy_lock);
}
/* Marvell Phy Initailization */
adv |= PHY_M_AN_10_FD;
if (skge->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
-
- /* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- adv |= PHY_B_P_NO_PAUSE;
- break;
- case FLOW_MODE_LOC_SEND:
- adv |= PHY_B_P_ASYM_MD;
- break;
- case FLOW_MODE_SYMMETRIC:
- adv |= PHY_B_P_SYM_MD;
- break;
- case FLOW_MODE_REM_SEND:
- adv |= PHY_B_P_BOTH_MD;
- break;
- }
- } else { /* special defines for FIBER (88E1011S only) */
+ } else /* special defines for FIBER (88E1011S only) */
adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
- /* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- adv |= PHY_M_P_NO_PAUSE_X;
- break;
- case FLOW_MODE_LOC_SEND:
- adv |= PHY_M_P_ASYM_MD_X;
- break;
- case FLOW_MODE_SYMMETRIC:
- adv |= PHY_M_P_SYM_MD_X;
- break;
- case FLOW_MODE_REM_SEND:
- adv |= PHY_M_P_BOTH_MD_X;
- break;
- }
- }
+ /* Set Flow-control capabilities */
+ adv |= phy_pause_map[skge->flow_control];
+
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
} else {
netif_stop_queue(dev);
del_timer_sync(&skge->led_blink);
- del_timer_sync(&skge->link_check);
/* Stop transmitter */
skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
u32 mode;
u8 filter[8];
+ pr_debug("genesis_set_multicast flags=%x count=%d\n", dev->flags, dev->mc_count);
+
mode = xm_read32(hw, port, XM_MODE);
mode |= XM_MD_ENA_HASH;
if (dev->flags & IFF_PROMISC)
else {
memset(filter, 0, sizeof(filter));
for (i = 0; list && i < count; i++, list = list->next) {
- u32 crc = crc32_le(~0, list->dmi_addr, ETH_ALEN);
- u8 bit = 63 - (crc & 63);
-
+ u32 crc, bit;
+ crc = ether_crc_le(ETH_ALEN, list->dmi_addr);
+ bit = ~crc & 0x3f;
filter[bit/8] |= 1 << (bit%8);
}
}
- xm_outhash(hw, port, XM_HSM, filter);
-
xm_write32(hw, port, XM_MODE, mode);
+ xm_outhash(hw, port, XM_HSM, filter);
}
static void yukon_set_multicast(struct net_device *dev)
if (hw->chip_id != CHIP_ID_GENESIS)
yukon_phy_intr(skge);
else
- genesis_bcom_intr(skge);
+ bcom_phy_intr(skge);
}
}
spin_unlock(&hw->phy_lock);
spin_lock_init(&skge->tx_lock);
- init_timer(&skge->link_check);
- skge->link_check.function = skge_link_timer;
- skge->link_check.data = (unsigned long) skge;
-
init_timer(&skge->led_blink);
skge->led_blink.function = skge_blink_timer;
skge->led_blink.data = (unsigned long) skge;
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff