+++ /dev/null
-Wed 2-Aug-95 <matti.aarnio@utu.fi>
-
- Linux network driver modules
-
- Do not mistake this for "README.modules" at the top-level
- directory! That document tells about modules in general, while
- this one tells only about network device driver modules.
-
- This is a potpourri of INSMOD-time(*) configuration options
- (if such exists) and their default values of various modules
- in the Linux network drivers collection.
-
- Some modules have also hidden (= non-documented) tunable values.
- The choice of not documenting them is based on general belief, that
- the less the user needs to know, the better. (There are things that
- driver developers can use, others should not confuse themselves.)
-
- In many cases it is highly preferred that insmod:ing is done
- ONLY with defining an explicit address for the card, AND BY
- NOT USING AUTO-PROBING!
-
- Now most cards have some explicitly defined base address that they
- are compiled with (to avoid auto-probing, among other things).
- If that compiled value does not match your actual configuration,
- do use the "io=0xXXX" -parameter for the insmod, and give there
- a value matching your environment.
-
- If you are adventurous, you can ask the driver to autoprobe
- by using the "io=0" parameter, however it is a potentially dangerous
- thing to do in a live system. (If you don't know where the
- card is located, you can try autoprobing, and after possible
- crash recovery, insmod with proper IO-address..)
-
- --------------------------
- (*) "INSMOD-time" means when you load module with
- /sbin/insmod you can feed it optional parameters.
- See "man insmod".
- --------------------------
-
-
- 8390 based Network Modules (Paul Gortmaker, Nov 12, 1995)
- --------------------------
-
-(Includes: smc-ultra, ne, wd, 3c503, hp, hp-plus, e2100 and ac3200)
-
-The 8390 series of network drivers now support multiple card systems without
-reloading the same module multiple times (memory efficient!) This is done by
-specifying multiple comma separated values, such as:
-
- insmod 3c503.o io=0x280,0x300,0x330,0x350 xcvr=0,1,0,1
-
-The above would have the one module controlling four 3c503 cards, with card 2
-and 4 using external transceivers. The "insmod" manual describes the usage
-of comma separated value lists.
-
-It is *STRONGLY RECOMMENDED* that you supply "io=" instead of autoprobing.
-If an "io=" argument is not supplied, then the ISA drivers will complain
-about autoprobing being not recommended, and begrudgingly autoprobe for
-a *SINGLE CARD ONLY* -- if you want to use multiple cards you *have* to
-supply an "io=0xNNN,0xQQQ,..." argument.
-
-The ne module is an exception to the above. A NE2000 is essentially an
-8390 chip, some bus glue and some RAM. Because of this, the ne probe is
-more invasive than the rest, and so at boot we make sure the ne probe is
-done last of all the 8390 cards (so that it won't trip over other 8390 based
-cards) With modules we can't ensure that all other non-ne 8390 cards have
-already been found. Because of this, the ne module REQUIRES an "io=0xNNN"
-argument passed in via insmod. It will refuse to autoprobe.
-
-It is also worth noting that auto-IRQ probably isn't as reliable during
-the flurry of interrupt activity on a running machine. Cards such as the
-ne2000 that can't get the IRQ setting from an EEPROM or configuration
-register are probably best supplied with an "irq=M" argument as well.
-
-
-----------------------------------------------------------------------
-Card/Module List - Configurable Parameters and Default Values
-----------------------------------------------------------------------
-
-3c501.c:
- io = 0x280 IO base address
- irq = 5 IRQ
- (Probes ports: 0x280, 0x300)
-
-3c503.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ software selected by driver using autoIRQ)
- xcvr = 0 (Use xcvr=1 to select external transceiver.)
- (Probes ports: 0x300, 0x310, 0x330, 0x350, 0x250, 0x280, 0x2A0, 0x2E0)
-
-3c505.c:
- io = 0
- irq = 0
- dma = 6 (not autoprobed)
- (Probes ports: 0x300, 0x280, 0x310)
-
-3c507.c:
- io = 0x300
- irq = 0
- (Probes ports: 0x300, 0x320, 0x340, 0x280)
-
-3c509.c:
- io = 0
- irq = 0
- ( Module load-time probing Works reliably only on EISA, ISA ID-PROBE
- IS NOT RELIABLE! Compile this driver statically into kernel for
- now, if you need it auto-probing on an ISA-bus machine. )
-
-8390.c:
- (No public options, several other modules need this one)
-
-a2065.c:
- Since this is a Zorro board, it supports full autoprobing, even for
- multiple boards. (m68k/Amiga)
-
-ac3200.c:
- io = 0 (Checks 0x1000 to 0x8fff in 0x1000 intervals)
- irq = 0 (Read from config register)
- (EISA probing..)
-
-apricot.c:
- io = 0x300 (Can't be altered!)
- irq = 10
-
-arcnet.c:
- io = 0
- irqnum = 0
- shmem = 0
- num = 0
- DO SET THESE MANUALLY AT INSMOD!
- (When probing, looks at the following possible addresses:
- Suggested ones:
- 0x300, 0x2E0, 0x2F0, 0x2D0
- Other ones:
- 0x200, 0x210, 0x220, 0x230, 0x240, 0x250, 0x260, 0x270,
- 0x280, 0x290, 0x2A0, 0x2B0, 0x2C0,
- 0x310, 0x320, 0x330, 0x340, 0x350, 0x360, 0x370,
- 0x380, 0x390, 0x3A0, 0x3E0, 0x3F0 )
-
-ariadne.c:
- Since this is a Zorro board, it supports full autoprobing, even for
- multiple boards. (m68k/Amiga)
-
-at1700.c:
- io = 0x260
- irq = 0
- (Probes ports: 0x260, 0x280, 0x2A0, 0x240, 0x340, 0x320, 0x380, 0x300)
-
-atarilance.c:
- Supports full autoprobing. (m68k/Atari)
-
-atp.c: *Not modularized*
- (Probes ports: 0x378, 0x278, 0x3BC;
- fixed IRQs: 5 and 7 )
-
-cops.c:
- io = 0x240
- irq = 5
- nodeid = 0 (AutoSelect = 0, NodeID 1-254 is hand selected.)
- (Probes ports: 0x240, 0x340, 0x200, 0x210, 0x220, 0x230, 0x260,
- 0x2A0, 0x300, 0x310, 0x320, 0x330, 0x350, 0x360)
-
-de4x5.c:
- io = 0x000b
- irq = 10
- is_not_dec = 0 -- For non-DEC card using DEC 21040/21041/21140 chip, set this to 1
- (EISA, and PCI probing)
-
-de600.c:
- de600_debug = 0
- (On port 0x378, irq 7 -- lpt1; compile time configurable)
-
-de620.c:
- bnc = 0, utp = 0 <-- Force media by setting either.
- io = 0x378 (also compile-time configurable)
- irq = 7
-
-depca.c:
- io = 0x200
- irq = 7
- (Probes ports: ISA: 0x300, 0x200;
- EISA: 0x0c00 )
-
-dummy.c:
- No options
-
-e2100.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ software selected by driver)
- mem = 0 (Override default shared memory start of 0xd0000)
- xcvr = 0 (Use xcvr=1 to select external transceiver.)
- (Probes ports: 0x300, 0x280, 0x380, 0x220)
-
-eepro.c:
- io = 0x200
- irq = 0
- (Probes ports: 0x200, 0x240, 0x280, 0x2C0, 0x300, 0x320, 0x340, 0x360)
-
-eexpress.c:
- io = 0x300
- irq = 0 (IRQ value read from EEPROM)
- (Probes ports: 0x300, 0x270, 0x320, 0x340)
-
-eql.c:
- (No parameters)
-
-ewrk3.c:
- io = 0x300
- irq = 5
- (With module no autoprobing!
- On EISA-bus does EISA probing.
- Static linkage probes ports on ISA bus:
- 0x100, 0x120, 0x140, 0x160, 0x180, 0x1A0, 0x1C0,
- 0x200, 0x220, 0x240, 0x260, 0x280, 0x2A0, 0x2C0, 0x2E0,
- 0x300, 0x340, 0x360, 0x380, 0x3A0, 0x3C0)
-
-hp-plus.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ read from configuration register)
- (Probes ports: 0x200, 0x240, 0x280, 0x2C0, 0x300, 0x320, 0x340)
-
-hp.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ software selected by driver using autoIRQ)
- (Probes ports: 0x300, 0x320, 0x340, 0x280, 0x2C0, 0x200, 0x240)
-
-hp100.c:
- hp100_port = 0 (IO-base address)
- (Does EISA-probing, if on EISA-slot;
- On ISA-bus probes all ports from 0x100 thru to 0x3E0
- in increments of 0x020)
-
-hydra.c:
- Since this is a Zorro board, it supports full autoprobing, even for
- multiple boards. (m68k/Amiga)
-
-ibmtr.c:
- io = 0xa20, 0xa24 (autoprobed by default)
- irq = 0 (driver cannot select irq - read from hardware)
- mem = 0 (shared memory base set at 0xd0000 and not yet
- able to override thru mem= parameter.)
-
-lance.c: *Not modularized*
- (PCI, and ISA probing; "CONFIG_PCI" needed for PCI support)
- (Probes ISA ports: 0x300, 0x320, 0x340, 0x360)
-
-loopback.c: *Static kernel component*
-
-ne.c:
- io = 0 (Explicitly *requires* an "io=0xNNN" value)
- irq = 0 (Tries to determine configured IRQ via autoIRQ)
- (Probes ports: 0x300, 0x280, 0x320, 0x340, 0x360)
-
-net_init.c: *Static kernel component*
-
-ni52.c: *Not modularized*
- (Probes ports: 0x300, 0x280, 0x360, 0x320, 0x340
- mems: 0xD0000, 0xD2000, 0xC8000, 0xCA000,
- 0xD4000, 0xD6000, 0xD8000 )
-
-ni65.c: *Not modularized* **16MB MEMORY BARRIER BUG**
- (Probes ports: 0x300, 0x320, 0x340, 0x360)
-
-pi2.c: *Not modularized* (well, NON-STANDARD modularization!)
- Only one card supported at this time.
- (Probes ports: 0x380, 0x300, 0x320, 0x340, 0x360, 0x3A0)
-
-plip.c:
- io = 0
- irq = 0 (by default, uses IRQ 5 for port at 0x3bc, IRQ 7
- for port at 0x378, and IRQ 2 for port at 0x278)
- (Probes ports: 0x278, 0x378, 0x3bc)
-
-ppp.c:
- No options (ppp-2.2+ has some, this is based on non-dynamic
- version from ppp-2.1.2d)
-
-seeq8005.c: *Not modularized*
- (Probes ports: 0x300, 0x320, 0x340, 0x360)
-
-skeleton.c: *Skeleton*
-
-slhc.c:
- No configuration parameters
-
-slip.c:
- slip_maxdev = 256 (default value from SL_NRUNIT on slip.h)
-
-
-smc-ultra.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ val. read from EEPROM)
- (Probes ports: 0x200, 0x220, 0x240, 0x280, 0x300, 0x340, 0x380)
-
-tulip.c: *Partial modularization*
- (init-time memory allocation makes problems..)
-
-tunnel.c:
- No insmod parameters
-
-wavelan.c:
- io = 0x390 (Settable, but change not recommended)
- irq = 0 (Not honoured, if changed..)
-
-wd.c:
- io = 0 (It will complain if you don't supply an "io=0xNNN")
- irq = 0 (IRQ val. read from EEPROM, ancient cards use autoIRQ)
- mem = 0 (Force shared-memory on address 0xC8000, or whatever..)
- mem_end = 0 (Force non-std. mem. size via supplying mem_end val.)
- (eg. for 32k WD8003EBT, use mem=0xd0000 mem_end=0xd8000)
- (Probes ports: 0x300, 0x280, 0x380, 0x240)
-
-znet.c: *Not modularized*
- (Only one device on Zenith Z-Note (notebook?) systems,
- configuration information from (EE)PROM)
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff